Installation. American Dynamics VM16 Plus, RCTT16BE, View Manager 16 Plus

T

OUCH

T

RACKER

Installation

RVEIMKITE T

OUCH

T

RACKER

Installation Kit

Part Number

6003-0047-01

5899-0004-102

2880-0083-01

2816-7634-44

2109-0254-04

2141-0002

6002-0024-01

0649-0006-02

0649-0006-04

2450-0008-01

3600-0032-01

0300-1000-01

6003-0107-01

2125-0007-02

2130-0021-01

2103-0092-01

8000-2672-01

0649-0006-06

8000-2653-01

8000-2654-01

8000-1370-02

6003-0108-01

RPNR00

Description

CBL/A, MDR, 14',8 C,CROSS-P'D

SCR, TCUT, M2.9X9.5, PHP, ST,Z,T1

ANCH, PL, W/O SCR, 3/4L,#4-#6-#8

SCR, TYP AB, PHP, ST, Z, 8X1

CON, P, EUR,.2C,28-12G,1X5P

LUG, SPADE, INSUL, 22-168

CBL, 3C, 18G, CM

BAG PLASTIC 4 X 6 1/2 4MIL

BAG PLASTIC 8 X 10 4 MIL THK

LBL, BLNK, PAP, THERM, 89X76M, RL

PRINTING SPEC, LABEL

INTERCONNECT BOX, TOUCH TRACK

CBL/A, QUAD, SW, INTFCE

HOOD, D, 9P, EMI/RFI, 1/4 D CBL

CON, D,P, HSG, 9P, SSI

CONT, P, D, 26-22,AU

INSTL INSTRS, TT ENHANCED

BAG, PLASTIC 12-1/2 X 14X4MIL

SYS OPERATOR'S MANUAL, VM16

SYS QUICK GUIDE, VM16

TTRACKER STRAIN RELIEF INSTR

CBL/A, VM16+/TNG, MUX/INTFCE

CBL/A, RS-232, 10', DB9F-DB9M

For Quad Splitter (RVQX7X) with DB9 Connector

1

1

1

1

1

3

1

1

1

1

1

1

1

1

1

1

0

Quantity

1

1

2

2

1

3

16.5

These additional parts are required.

PN Description

2103-0092-02 DB9 Female contact pins

2103-0092-01 DB9 Male contact pins

2130-0021-01 DB9 Male Connector

2130-0022-01 DB9 Female Connector

Quantity

2

5

5

1

1

!

WARNING: RISK OF ELECTRIC

SHOCK! Disconnect AC Power to the switch.

!

CAUTION-Electrostatic Sensitive

Device: Follow proper handling procedures to prevent component failure.

Note: Prior to installing the Enhanced T OUCH

T RACKERS , identify the type of external unit that will connect to the Enhanced T OUCH T RACKER , if applicable. Build any cables that are required.

Refer to the Installation Diagrams starting on page 3 for specific instructions.

1. Terminate the External Interconnect Module

(EIM) at the end of the SensorNet network. If more than one Enhanced T OUCH T RACKER controller will be installed, one T OUCH

T RACKER 's EIM will be terminated; the other EIM will be unterminated. Refer to the appropriate wiring diagram for your configuration.

2. Mount each EIM on a wall or other surface within 3m (10 feet) of the Touch Tracker controller.

3. Connect the power transformer and SensorNet cable to J3 on each EIM. If two Touch Trackers will be installed, connect the SensorNet cable from the first EIM to the second EIM.

4. Depending on the external unit that will be attached to your system, connect the appropriate cable to the DB9 connector on the

EIM. Refer to the appropriate wiring diagram for additional details.

5. Connect the data cable from J1 on the Primary

T OUCH T RACKER 's EIM to the remote port on the external unit. Refer to the appropriate wiring diagram for additional details.

6. Connect the modular cable from J2 on each

EIM to the T OUCH T RACKER controller.

7. Connect the SensorNet cable from the dome to the first EIM. Refer to the appropriate wiring diagram for additional details.

8. Plug in the power transformer into a grounded,

3-wire receptacle.

Note: If the keypad and backlighting do not illuminate when power is applied, unplug each power transformer and repeat steps 3 through 8.

Depending on system configuration, it may take up to 2 minutes for the Enhanced T OUCH T RACKER to come completely online.

Continue with Configuring the External Device.

8000-2672-01, REV. D1 RCTT16BE VM16 PLUS ENHANCED TOUCH TRACKER

INSTALLATION GUIDE

2 of 15