- Computers & electronics
- Computer components
- System components
- Motherboards
- ASROCK
- H61M/U3S3
- User manual
advertisement
2.3 CPU Installation
For the installation of Intel 1155-Pin CPU, please follow the steps below.
Load Plate
Load Lever
Socket Body
Contact Array
1155-Pin Socket Overview
Before you insert the 1155-Pin CPU into the socket, please check if the
CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.
Step 2. Remove PnP Cap (Pick and Place Cap).
1. It is recommended to use the cap tab to handle and avoid kicking
off the PnP cap.
2. This cap must be placed if returning the motherboard for after
service.
15
Step 3. Insert the 1155-Pin CPU:
Step 3-1. Hold the CPU by the edge where is marked with black line.
Step 3-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two orientation key notches.
orientation key notch alignment key
Pin1 alignment key
1155-Pin Socket orientation key notch
1155-Pin CPU
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
Step 3-3. Carefully place the CPU into the socket by using a purely vertical motion.
Step 3-4. Verify that the CPU is within the socket and properly mated to the orient keys.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load plate, engage the load lever.
Pin1
16
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 1 Introduction
- 5 1.1 Package Contents
- 6 1.2 Specifi cations
- 12 1.3 Motherboard Layout
- 14 2 Installation
- 14 2.1 Screw Holes
- 14 2.2 Pre-installation Precautions
- 15 2.3 CPU Installation
- 17 2.4 Installation of Heatsink and CPU fan
- 20 2.7 Dual Monitor and Surround Display Features
- 23 2.8 ASRock Smart Remote Installation Guide
- 24 2.9 Jumpers Setup
- 25 2.10 Onboard Headers and Connectors
- 29 Installation
- 29 2.12 Serial ATA3 (SATA3) Hard Disks Installation
- 30 2.13 Hot Plug Function for SATA / SATAII HDDs
- 30 2.14 Hot Plug Function for SATA3 HDDs
- 31 Operation Guide
- 33 2.16 Driver Installation Guide
- 33 / XP / XP 64-bit Without RAID Functions
- 33 Functions
- 34 64-bit Without RAID Functions
- 35 3 UEFI SETUP UTILITY
- 35 3.1 Introduction
- 35 3.1.1 UEFI Menu Bar
- 36 3.1.2 Navigation Keys
- 36 3.2 Main Screen
- 37 3.3 OC Tweaker Screen
- 40 3.4 Advanced Screen
- 41 3.4.1 CPU Con guration
- 43 3.4.2 North Bridge Con guration
- 45 3.4.3 South Bridge Con guration
- 46 3.4.4 Storage Con guration
- 47 3.4.5 Super IO Con guration
- 48 3.4.6 ACPI Con guration
- 49 3.4.7 USB Con guration
- 50 3.5 Hardware Health Event Monitoring Screen
- 51 3.6 Boot Screen
- 52 3.7 Security Screen
- 53 3.8 Exit Screen
- 54 4 Software Support
- 54 4.1 Install Operating System
- 54 4.2 Support CD Information
- 54 4.2.1 Running Support CD
- 54 4.2.2 Drivers Menu
- 54 4.2.3 Utilities Menu
- 54 4.2.4 Contact Information