using your freezer. Whirlpool EH18EF, EH23EF, EHl5EF
Add to my manuals
12 Pages
Whirlpool EH18EF is a chest freezer which allows you to store frozen food, make ice, and features a 18 cubic feet capacity. It comes with a key eject lock to prevent unauthorized access, adjustable temperature control, and a signal light to warn of any unexpected failure. Additionally, the sliding baskets and defrost drain cover make it easy to organize and defrost your freezer.
advertisement
Setting the temperature control...
I. Insert a coin in the slot of the Temperature Control to turn it.
2. Turn control to Number 3. This setting is designed to maintain the temperature at or near 0°F ( ~ 17.8”C) under normal operating conditions.
Adjusting the temperature control...
1 Turn control to higher number for colder temper- atures.
2. Turn to lower number for less cold temperatures.
Cooling freezer first...
1 Allow freezer to cool 6 to 8 hours before filling with frozen food.
2. Let it cool overnight before adding large amount of unfrozen food.
Note: When freezer is first started, the compressor will run constantly until the cabrnet is cooled It may take up to 6 to 8 hours or longer, depending on room temperature and the number of times the freezer door is opened.
After the cabinet is cooled, the compressor WIII turn ON and OFF as needed to keep the freezer at the proper temperature
The sliding baskets...
Can be moved from side to side or removed when loading or unloading food below it.
To remove:
Lift basket out
To replace: l.ower basket into place
The key eject lock...
can help reduce the hazard of child entrapment
To lock or unlock the freezer you must hold the key rn the lock while turning The lock IS sprrng loaded so the key cannot be left in the lock.
If the key is lost, contact your WHIRLPOOL dealer for a replacement. Always grve the com- plete model and serial number of your freezer when requesting a replacement key.
The signal light...
automatically failure. warns of any unexpected power l l l
If the signal light is not glowing, immediately check: for power interruption, for an unplugged power cord, for a burned out signal light.
To replace:
1. Unplug power cord from outlet.
2. Carefully snap out light cover and assembly with a screwdriver by inserting it under the end of metal edge of the light. Be careful not to chip finish on freezer.
3. Unplug burned out signal light and replace with a new one. Signal light can be ordered from your
WHIRLPOOL dealer
4. Then, snap light assembly into place.
5. Plug power cord into outlet.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 front cover
- 2 parts and features
- 3 toc
- 3 safety first
- 3 before you plug it in
- 4 install properly
- 4 level chest freezer
- 4 remove sales labels
- 4 install defrost drain cover
- 4 clean it
- 4 plug it in
- 5 using your freezer
- 5 setting the temperature control
- 5 adjusting the temperature control
- 5 cooling freezer first
- 5 the sliding baskets
- 5 the key eject lock
- 5 the signal light
- 6 energy saving tips
- 6 cleaning your freezer
- 6 cleaning chart
- 7 freezing food in your freezer
- 7 packaging and sealing food
- 7 to wrap foods
- 8 loading
- 8 storing frozen food
- 9 vacation and moving care
- 9 vacations
- 9 shutting off and moving
- 10 if you need service or assistance
- 10 1. before calling for assistance
- 10 2. if you need assistance
- 11 3. if you need service
- 11 4. if you have a problem
- 12 back cover