advertisement
28
CHAPTER 8: TROUBLESHOOTING
8.12 TROUBLESHOOTING - NO POWER TO THE CONSOLE
POWER SWITCH IS ON, BUT THE CONSOLE HAS NO DISPLAY
POSSIBLE CAUSES:
1) The unit is not getting power from the outlet.
2) The LCB is not getting power from the power receptacle.
3 & 4) The LCB LEDs are lit, but there is no power to the console.
SOLUTION:
1) Verify power at the outlet. If the outlet is not outputting 120VAC, check the fitness room power.
2) Remove the front disk and check to see if LED1 is lit on the LCB (Figure A).
a. If it is not lit, verify power at the outlet. if the outlet is not outputting 120V power, check the fitness room power.
b. If LED9 is still not lit, check the incoming AC power to the LCB. If the incoming power is not correct, replace the power cord.
c. Replace the LCB if all power components are OK and there are AC volts to the LCB.
3 & 4) Remove the front disk and check to see if LED1 is lit on the LCB.
a. If LED9 is lit, check the connection of the console cable.
b. If the console cable is connected properly, LED2 on the control board should be lit (Figure B). If it is not lit, check voltage on the console cable. Measure voltage across pins 1 and 3 of the cable, it should show around 12V. Replace the console cable if this reading is off.
c. If LED2 on the control board is lit, but there is still no power to the console, replace the console.
FIGURE A FIGURE B
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 CHAPTER 1: SERIAL NUMBER LOCATION
- 6 Read and Save These Instructions
- 7 Electrical Requirements
- 8 Recommended Cleaning Tips
- 8 Check for Damaged Parts
- 9 Care and Maintenance Instructions
- 10 Console Description
- 11 Workout Setup Steps - Manual
- 11 Workout Setup Steps - Fat Burn
- 11 Workout Setup Steps - Level Based
- 12 Workout Setup Steps - Fitness Test
- 13 Workout Setup Steps - Target Heart Rate
- 13 Workout Setup Steps - Constant Watts
- 14 Using Manager Mode
- 14 Manager Mode Overview
- 15 Using Engineering Mode
- 16 Using Service Mode
- 17 Electrical Diagram
- 22 LCB LED Indicators
- 23 Troubleshooting - Error 04A
- 24 Troubleshooting - Error 04B
- 25 Troubleshooting - Error
- 26 Troubleshooting - Error 02B4 / 03A8 / 02AB
- 27 Troubleshooting - Error 0149 / 01AF
- 28 Troubleshooting - Error 01B
- 29 Troubleshooting - No Resistance
- 30 Troubleshooting - Heart Rate Issues
- 31 Troubleshooting - No Power to the Console
- 32 Troubleshooting - Keypad Issues
- 33 Console Replacement
- 34 Handlebar Replacement
- 35 Cup Holder Replacement
- 36 Keypad / Overlay Replacement
- 38 Seat Pad Replacement
- 39 Back Pad Replacement
- 40 HR Grips Replacement
- 41 Seat Set Replacement
- 42 Seat Slide Replacement
- 44 Rear Covers Replacement
- 45 Guide Rail Set Replacement
- 46 Pedal Replacement
- 47 Crank Axle Set Replacement
- 48 Front Shrouds Replacement
- 49 Front Covers Replacement
- 50 Console Mast Removal
- 51 Lower Control Board Replacement
- 52 Battery Replacement
- 53 Drive Belt Replacement
- 54 Generator Replacement
- 55 Rear Stabilizer Replacement
- 56 Front Stabilizer Replacement
- 57 Drive Axle Set Replacement
- 61 Testing the Bike
- 62 R5x-05 Bike Specifications
- 63 Assembly Instructions
- 70 Adjusting the Pedal Straps and Seat
- 71 Leveling the Bike
- 77 Software Upgrade Procedure