advertisement
CHAPTER 8: TROUBLESHOOTING
8.13 TROUBLESHOOTING - KEYPAD ISSUES
ALL OR SOME OF THE FUNCTION KEYS DO NOT RESPOND
POSSIBLE CAUSES:
1) The keypad connection ribbon cable has not been plugged in correctly.
2) The keypad is damaged.
3) The UCB is damaged.
SOLUTION:
1) Perform a keypad test in Service Mode:
a. Press and hold both the UP and DOWN LEVEL keys until Manager Mode appears on the display.
b. Use the UP and DOWN LEVEL keys to scroll to Service Mode 2 and press ENTER.
c. Test the affected keypad. If the keypad works in the keypad test it may not be a functioning key in the program used for testing it.
2) Check the connections of the keypad at the UCB.
a. Remove the console from the console mast.
b. Remove the 6 screws holding the back of the console to the front (Figure A).
c. Inspect the keypad ribbon cable connection at the UCB (Figure B).
d. Even if the keypad ribbon cable appears to be connected correctly, unplug and re-seat the cable.
3) Replace the affected keypad.
4) Replace the console.
FIGURE A FIGURE B
29
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 CHAPTER 1: SERIAL NUMBER LOCATION
- 6 Read and Save These Instructions
- 7 Electrical Requirements
- 8 Recommended Cleaning Tips
- 8 Check for Damaged Parts
- 9 Care and Maintenance Instructions
- 10 Console Description
- 11 Workout Setup Steps - Manual
- 11 Workout Setup Steps - Fat Burn
- 11 Workout Setup Steps - Level Based
- 12 Workout Setup Steps - Fitness Test
- 13 Workout Setup Steps - Target Heart Rate
- 13 Workout Setup Steps - Constant Watts
- 14 Using Manager Mode
- 14 Manager Mode Overview
- 15 Using Engineering Mode
- 16 Using Service Mode
- 17 Electrical Diagram
- 22 LCB LED Indicators
- 23 Troubleshooting - Error 04A
- 24 Troubleshooting - Error 04B
- 25 Troubleshooting - Error
- 26 Troubleshooting - Error 02B4 / 03A8 / 02AB
- 27 Troubleshooting - Error 0149 / 01AF
- 28 Troubleshooting - Error 01B
- 29 Troubleshooting - No Resistance
- 30 Troubleshooting - Heart Rate Issues
- 31 Troubleshooting - No Power to the Console
- 32 Troubleshooting - Keypad Issues
- 33 Console Replacement
- 34 Handlebar Replacement
- 35 Cup Holder Replacement
- 36 Keypad / Overlay Replacement
- 38 Seat Pad Replacement
- 39 Back Pad Replacement
- 40 HR Grips Replacement
- 41 Seat Set Replacement
- 42 Seat Slide Replacement
- 44 Rear Covers Replacement
- 45 Guide Rail Set Replacement
- 46 Pedal Replacement
- 47 Crank Axle Set Replacement
- 48 Front Shrouds Replacement
- 49 Front Covers Replacement
- 50 Console Mast Removal
- 51 Lower Control Board Replacement
- 52 Battery Replacement
- 53 Drive Belt Replacement
- 54 Generator Replacement
- 55 Rear Stabilizer Replacement
- 56 Front Stabilizer Replacement
- 57 Drive Axle Set Replacement
- 61 Testing the Bike
- 62 R5x-05 Bike Specifications
- 63 Assembly Instructions
- 70 Adjusting the Pedal Straps and Seat
- 71 Leveling the Bike
- 77 Software Upgrade Procedure