advertisement
▼
Scroll to page 2
of
206
Appendix B
Cable Pinouts
Standard Cable Pinouts (Primary Interface Cables)
Pin # RS-232
IBM Port 5B/
9B/17
USB-OEM
USB,
USB
Keyboard,
USB COM
DTR
CTS
5
6
7
3
4
1
2
8
9
10
RTS
RxD
TxD
VCC in
GND
Line B
Line A
VCC in
GND
VBUS
D-
D+
+12V
GND
VBUS
D-
D+
VCC in
GND
Keyboard
Wedge
PCCLK
KBCLK
PC Data
VCC in
GND
KBD
Product Reference Guide 153
Cable Pinouts (Handheld Scanner Attached via the Aux Port)
PIN #
HANDHELD ATTACHED
TO AUX PORT
7
8
5
6
9
10
3
4
1
2 AUX_CTS
AUX_RTS
AUX_RxD
AUX_TxD
AUX_ERI
VCC
GND
154 Magellan™ 3200VSI
advertisement
Related manuals
advertisement
Table of contents
- 3 Table of Contents
- 9 Getting Started
- 9 About This Manual
- 9 Manual Conventions
- 10 Connecting the Scanner
- 12 Error Codes
- 12 LED Class
- 13 Mount Installation
- 14 Wall Mount
- 14 Countertop Mount
- 15 LED and Beeper Indicators
- 17 Programming
- 17 Introduction to Label Programming
- 17 Understanding the Basics
- 17 Using the Programming Bar Codes
- 18 Resetting the Standard Product Defaults
- 18 Data Matrix Programming Labels
- 19 Using a Bar Code Mask
- 19 Going Green
- 20 Bar Code Mask
- 21 General Features
- 21 Double Read Timeout for Linear Labels
- 23 Double Read Timeout for 2D Labels
- 24 Scanner Button Options
- 25 Camera Button Mode
- 26 Auto Cell Phone Mode
- 26 Auto Cell Phone Mode Enable
- 27 LED Level
- 28 Auxiliary Port Mode
- 29 Auxiliary Port Baud Rate
- 30 Productivity Index Reporting (PIR)
- 31 Sleep Mode
- 33 LED and Beeper Indicators
- 33 Power On Alert
- 33 External Read Indicator (ERI) Active State High
- 34 ERI Timeout
- 35 Good Read: When to Indicate
- 36 Good Read Beep Control
- 36 Good Read Beep Frequency
- 37 Good Read Beep Length
- 38 Good Read Beep Volume
- 39 Scanning Features
- 39 Wake Up Intensity
- 41 Image Capture
- 41 Image Capture
- 41 How to Capture an Image
- 41 Image Capture to a microSD Card by Scanning a Special Label
- 42 Image Capture to the Host by Host Command
- 43 Image Compression
- 43 Image Format
- 44 Image Size
- 45 Image Brightness
- 45 Image Contrast
- 47 Interface Related Features
- 49 Interface Selection
- 51 Interface Features
- 51 Obey/Ignore Host Commands
- 51 Host Transmission Buffers
- 52 RS-232 Interface Features
- 54 Hardware Flow Control
- 55 Intercharacter Delay
- 56 Software Flow Control
- 57 Host Echo
- 58 Host Echo Quiet Interval
- 59 Signal Voltage: Normal/TTL
- 60 RS-232 Invert
- 60 Beep on ASCII BEL
- 60 Beep on Not on File
- 61 ACK NAK Options
- 62 ACK Character
- 62 NAK Character
- 63 Retry on ACK NAK Timeout
- 63 ACK NAK Timeout Value
- 64 ACK NAK Retry Count
- 64 ACK NAK Error Handling
- 65 Transmission Failure Indication
- 66 Single Cable RS-232
- 66 Single Cable RS-232 Options
- 67 Single Cable RS-232 RTS CTS Selection
- 68 Single Cable RS-232 Use BCC
- 68 Single Cable RS-232 Use ACK/NAK
- 69 Single Cable RS-232 Use STX
- 69 Set Single Cable RS-232 STX Character
- 70 Single Cable RS-232 Use ETX
- 70 Set Single Cable RS-232 ETX Character
- 71 Single Cable Pacesetter Plus
- 71 Single Cable Datalogic Extensions
- 72 USB-OEM Interface Features
- 72 USB-OEM Device usage
- 72 IBM
- 72 IBM Transmit Labels in Code 39 Format
- 73 Keyboard Wedge
- 73 USB Keyboard
- 75 Caps Lock State
- 76 Power-On Simulation
- 77 Control Characters
- 78 Wedge Quiet Interval
- 79 Intercharacter Delay
- 79 USB-COM Interface Setup
- 81 Data Editing
- 81 Data Editing Overview
- 81 Please Keep In Mind...
- 82 Global Prefix/Suffix
- 83 AIM ID
- 84 Label ID
- 90 Case Conversion
- 91 Character Conversion
- 93 Symbologies
- 94 UPC-A
- 94 Disable/Enable UPC-A
- 94 Check Digit Transmission
- 95 Number System Transmission
- 95 Expand UPC-A to EAN-13
- 96 UPC-E
- 96 Disable/Enable UPC-E
- 96 Check Digit Transmission
- 97 Number System Digit
- 97 Expand to UPC-E to UPC-A
- 98 Expand UPC-E to EAN13
- 98 UPC/EAN Quiet Zone
- 99 GTIN
- 99 Expand UPC/EAN to GTIN
- 100 EAN-13
- 100 Disable/Enable EAN-13
- 100 Check Digit Transmission
- 101 EAN-13 Flag 1 Character
- 101 ISBN
- 102 EAN-8
- 102 Disable/Enable EAN-8
- 102 Check Digit Transmission
- 102 Expand EAN-8 to EAN-13
- 103 EAN Two-Label
- 103 EAN Two-Label Combined Transmission
- 104 Price Weight Check Digit
- 105 Add-ons
- 107 GS1 DataBar Omnidirectional / Stacked Omnidirectional
- 107 Disable/Enable GS1 DataBar Omnidirectional
- 107 UCC/EAN 128 Emulation
- 108 GS1 DataBar Expanded / Expanded Stacked
- 108 Disable/Enable GS1 DataBar Expanded
- 108 GS1-128 Emulation
- 109 GS1 DataBar Expanded Length Control
- 109 GS1 DataBar Expanded Length 1, Length 2 Programming Instructions
- 110 Coupon Read Control
- 111 GS1 DataBar Limited
- 111 Disable/Enable GS1 DataBar Limited
- 111 GS1-128 Emulation
- 112 Code 39
- 112 Disable/Enable Code 39
- 112 Check Character Calculation
- 113 Check Character Transmit
- 113 Start/Stop Characters
- 114 Code 39 Full ASCII
- 115 Code 39 Length Control
- 115 Code 39 Length 1, Length 2 Programming Instructions
- 116 Code 32 Italian Pharmacode
- 116 Disable/Enable Code 32 Italian Pharmacode
- 116 Start/Stop Characters
- 116 Check Character Transmit
- 117 Code 128
- 117 Disable/Enable Code 128
- 117 Disable/Enable EAN 128
- 118 Transmit Function Characters
- 118 Length Control
- 119 Code 128 Length 1, Length 2 Programming Instructions
- 119 Code 128 Conversion to Code 39
- 120 Interleaved 2 of 5
- 120 Disable/Enable Interleaved 2 of 5
- 120 Check Digit Calculation
- 120 Check Digit Transmit
- 121 Interleaved 2 of 5 Length Control
- 121 Interleaved 2 of 5 Length 1, Length 2 Programming Instructions
- 122 Codabar
- 122 Disable/Enable Codabar
- 122 Check Character Verification
- 123 Check Character Transmit
- 123 Codabar Length Control
- 124 Codabar Length 1, Length 2 Programming Instructions
- 124 Start/Stop Character Type
- 125 Start/Stop Character Transmission
- 125 Start/Stop Character Match
- 126 Code 93
- 126 Disable/Enable Code 93
- 126 Length Control
- 127 Code 93 Length 1, Length 2 Programming Instructions
- 128 MSI
- 128 Disable/Enable MSI
- 128 MSI Check Character Transmit
- 129 MSI Check Character Calculation
- 129 MSI Number of Check Characters
- 130 MSI Length Control
- 130 MSI Length 1, Length 2 Programming Instructions
- 131 2D Symbologies
- 132 PDF 417
- 132 Disable/Enable PDF 417
- 132 Allow Zero Length PDF 417 Reading
- 133 PDF 417 Length Control
- 134 PDF 417 Length 1, Length 2 Programming Instructions
- 135 Micro PDF 417
- 135 Disable/Enable Micro PDF 417
- 136 Micro PDF 417 Length Control
- 137 Micro PDF 417 Length 1, Length 2 Programming Instructions
- 138 Datamatrix
- 138 Disable/Enable Datamatrix
- 139 Datamatrix Length Control
- 140 Datamatrix Length 1, Length 2 Programming Instructions
- 141 QR Code
- 141 Disable/Enable QR Code
- 142 QR Code Length Control
- 142 Configuring Variable Length Decoding:
- 143 QR Code Length 1, Length 2 Programming Instructions
- 144 Maxicode
- 144 Disable/Enable Maxicode
- 145 Maxicode Length Control
- 145 Configuring Variable Length Decoding:
- 146 Maxicode Length 1, Length 2 Programming Instructions
- 147 Aztec
- 147 Disable/Enable Aztec
- 148 Aztec Length Control
- 148 Configuring Variable Length Decoding:
- 149 Aztec Length 1, Length 2 Programming Instructions
- 150 Composite Labels
- 150 Disable/Enable GS1 DataBar Omnidirectional 2D Component
- 150 Disable/Enable GS1 DataBar Expanded 2D Component
- 151 Disable/Enable GS1 DataBar Limited 2D Component
- 152 Advanced Decoding Features
- 152 Inverse Label Reading
- 153 References
- 153 Global Prefix/Suffix
- 154 Label ID
- 155 Length Control
- 155 Configuring Variable Length Decoding:
- 156 Length 1, Length 2 Programming Instructions
- 157 Product Specifications
- 157 Optical and Read Performance Parameters
- 157 Scanner Dimensions
- 158 Physical Properties
- 158 Electrical Parameters
- 158 Environmental Parameters
- 158 Other Parameters
- 159 LED and Beeper Indicators
- 161 Cable Pinouts
- 161 Standard Cable Pinouts (Primary Interface Cables)
- 162 Cable Pinouts (Handheld Scanner Attached via the Aux Port)
- 163 Alpha-Numeric Pad
- 165 Factory Default Settings
- 165 Factory Defaults by Interface
- 173 Keyboard Function Key Mappings
- 173 Keyboard Model Cross Reference
- 181 Host Commands
- 181 Accepting RS-232 Commands
- 183 Sample Symbols
- 183 1D Symbol Samples
- 185 2D Sample Symbols
- 186 Composite Sample Symbols
- 187 microSD Card
- 187 microSDHC Compatibility
- 187 microSD Card Insertion
- 188 microSD Card Removal
- 188 Autorun File Processing
- 189 microSD Function Summary
- 189 microSD Function Details
- 189 From Scanner to microSD Card
- 189 Capture and save an image to a microSD card by scanning a label.
- 190 Export a Configuration file from the Scanner to the microSD card
- 190 Export Scanner Status to microSD card
- 191 From microSD Card to Scanner
- 191 Application code load to scanner
- 191 Configuration load to scanner
- 193 Handheld Data Format Requirements
- 193 Handheld Data Format Requirements General
- 194 Datalogic Handheld Data Format Requirements
- 194 RSS-14
- 194 RSS Expanded
- 194 UPC-A
- 194 UPC-A with 2-Digit Supplemental
- 194 UPC-A with 5-Digit Supplemental
- 194 UPC-A with Code 128 Supplemental
- 195 UPC-E
- 195 UPC-E with 2-Digit Supplemental
- 195 UPC-E with 5-Digit Supplemental
- 195 UPC-E with Code 128 Supplemental
- 196 EAN-8
- 196 EAN-8 with 2-Digit Supplemental
- 196 EAN-8 with 5-Digit Supplemental
- 196 EAN-8 with Code 128 Supplemental
- 196 EAN-13
- 196 EAN-13 with 2-Digit Supplemental
- 196 EAN-13 with 5-Digit Supplemental
- 197 EAN-13 with Code 128 Supplemental
- 197 Code 39
- 197 Code 39-Pharmacode
- 197 I 2 of 5
- 198 Codabar
- 198 Code 128
- 199 MSI
- 199 Code 93
- 199 PDF417
- 200 AIM Formats
- 200 UPC-A
- 200 UPC-E
- 200 EAN-13
- 200 EAN-8
- 200 2-Digit Supplemental
- 200 5-Digit Supplemental
- 202 Code 128 Supplemental
- 202 Bookland
- 202 Code 39
- 202 Codabar
- 203 MSI
- 203 Code 93
- 203 RSS-14
- 203 RSS Expanded
- 203 I 2 of 5
- 203 Code 128 / EAN128
- 204 PDF417
- 204 “Unknown” AIM ID (an AIM ID which is not specified above)