advertisement
http://www.xiaoyu163.com
1.1
Safety Precautions
!
SECTION 1
8 9 2 4 9 8 2 9 9
Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
!
Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
TEL 13942296513 Q Q 3 7 6 3 1 5 1 5 0 8 9 2 4 9 8 2 9 9 www. xiaoyu163. com
1-4 (No.MA121) http://www.xiaoyu163.com
http://www.xiaoyu163.com
1.2
Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser QQ 376315150 8 9 2 4 9
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
8 2 9 9
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily destroy the laser diode.
1.3
Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4
Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Short-circuit point
(Soldering)
Flexible wire
Pickup www. xiaoyu163. com http://www.xiaoyu163.com
(No.MA121)1-5
advertisement
Related manuals
advertisement
Table of contents
- 4 SECTION 1 PRECAUTIONS
- 4 1.1 Safety Precautions
- 5 1.2 Preventing static electricity
- 5 1.3 Handling the traverse unit (optical pickup)
- 5 1.4 Attention when traverse unit is decomposed
- 6 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS
- 6 2.1 HOW TO IDENTIFY MODELS
- 7 SECTION 3 DISASSEMBLY
- 7 3.1 Main body section
- 10 3.2 CD Mechanism Assembly
- 25 SECTION 4 ADJUSTMENT
- 25 4.1 Adjustment method
- 26 SECTION 5 TROUBLESHOOTING
- 26 5.1 KD-G110 J and KD-S11 J version model
- 28 5.2 KD-G110 J2 and KD-S11 J2 version model
- 30 5.3 Maintenance of laser pickup
- 30 5.4 Replacement of laser pickup
- 31 5.5 16 PIN CORD DIAGRAM
- 33 Topcover
- 36 Block diagram (For J version)
- 38 Standard schematic diagrams (For J version)
- 44 Printed circuit boards (For J version)
- 46 Block diagram (For J2 version)
- 48 Standard schematic diagrams (For J2 version)
- 54 Printed circuit boards (For J2 version)
- 56 Backcover
- 57 Cover
- 58 Exploded view of general assembly and parts list(Block No.M1)
- 60 General Assembly
- 61 CD mechanism assembly and parts list(Block No.MB)
- 62 CD mechanism
- 63 Electrical parts list(Block No.01~04)
- 63 Main board(KD-G110,KD-S11_J)
- 65 Switch board(KD-G110,D-S11_J)
- 66 Main board(KD-G110,KD-S11_J2)
- 69 Switch board(KD-G110,KD-S11_J2)
- 70 Packing materials and accessories parts list(Block No.M3)
- 71 Packing and Accessories