- Computers & electronics
- Data input devices
- KVM switches
- Rose electronics
- CrystalView Plus
- Operations manual
Connecting the cables. Rose electronics CrystalView Plus CRV-SL1, CrystalView Plus CRV-SL2, CRV-R2V, CrystalView Plus CRV-R4V, CRV-R4V, CRK-1P1V, Switch CrystalView Plus, CrystalView Plus, CrystalView Plus CRV-DL1, CRV-R1V
Add to My manuals48 Pages
advertisement
Connecting the cables
CATx CABLE
LOCAL REMOTE
CPU
CABLE
SERIAL/AUDIO
KVM STATION SERIAL MIC SPEAKERS
Figure 6. Single video cabling
Local unit to CPU cabling
(Refer to Figure 1 and Figure 6)
The keyboard, video, and mouse ports on the CPU are connected to the keyboard, video, and mouse ports on the CrystalView plus using an appropriate CPU adapter cable.
Serial/audio models
(Refer to page 10 for a description of serial and audio cabling)
For the serial/audio models, connect the serial DB9M port on the
CPU to the DB9F serial connector on the CrystalView Plus using a
DB9F to DB9M serial cable.
The line out of the CPU’s sound card connects to the Line in port on the CrystalView Plus. The line in connects to the CrystalView Plus line out port. No set-up is needed.
Local KVM access models
Using models with local KVM access, a second KVM station can be connected to the local unit. The KVM station’s keyboard, video monitor, and mouse cables can generally be connected directly to the local access keyboard, monitor, and mouse ports on the local unit.
12 CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL
Remote unit to KVM station cabling
(Refer to Figure 2 and Figure 6)
On the remote unit, the KVM station’s keyboard, monitor, and mouse cables are connected directly to the CrystalView Plus keyboard, monitor, and mouse connectors.
Serial/audio models
(Refer to page 10 for a description of serial and audio cabling)
Serial port
The serial port on all models is a DB9F on the local unit and DB9M on the remote unit. The serial port on the remote unit is the same as the DB9M serial connector on your computer. Serial devices such as Touchscreens can connect directly to the serial port on the remote unit
.
Audio ports
A set of powered computer speakers can connect directly to the
CrystalView Plus remote unit’s line level audio out connector. A powered or non-powered microphone can connect to the Line level audio in (MIC) connector.
If you are using a non-powered microphone on the Remote Unit, install the “MIC” jumper, if needed, to provide additional amplification.
DO NOT INSTALL THE “MIC” JUMPER IF USING A
POWERED MICROPHONE.
(See page 10 for alternative ways to connect and install a powered or non-powered microphone)
Local unit to Remote unit cabling
Connect up to 1,000 feet of CAT-x cable from the Local Units RJ45 front panel connector to the Remote Units RJ45 front panel connector. (See Figure 6)
CRYSTALVIEW PLUS INSTALLATION AND OPERATIONS MANUAL 13
advertisement
Related manuals
advertisement
Table of contents
- 7 Disclaimer
- 7 System introduction
- 8 Features
- 9 Compatibility
- 9 Package contents
- 10 Single video Local models
- 11 Single video Remote models
- 12 Dual video local models
- 13 Dual video remote models
- 14 Quad video remote models
- 15 Cables
- 16 Serial cable
- 16 Audio cable
- 17 Installation
- 18 Connecting the cables
- 20 Dual Video cabling
- 22 Quad Video Remote Unit cabling
- 24 Keyboard commands
- 25 Keyboard command descriptions
- 28 Local unit Keyboard commands (Dual local model only)
- 30 Adjusting the video
- 33 Operating instructions- All units
- 33 Operating instructions – Dual unit
- 33 KVM Switching
- 33 Private mode (Dual access models only)
- 34 Troubleshooting
- 36 Service Information
- 36 Maintenance and Repair
- 36 Technical Support
- 37 Safety