advertisement
Chapter 1
Preparation
This chapter describes the necessary preparation for installation of the LT260.
This section describes the necessary information, and the devices and cables that should be prepared before you connect the LT260 to a Storage Area Network (SAN) and a LAN for operation management.
1.1
Host Connection
A SAN is a dedicated network for connecting a server (host) to an LT260. A Fibre Channel (FC)/Serial Attached
SCSI (SAS) interface can be used for the host interface. The connection destination may be the server or the switch depending on which connection configuration is used.
The host interface cables that are used for connecting the LT260 to a SAN must be obtained separately. When a switch is used to connect the LT260 to the server, the appropriate switch for the type of host interface that is to be connected must also be prepared separately.
1.2
Connection to LAN for Operation Management
The LT260 must be connected to the LAN for operation management during operation management and system maintenance.
Acquire an IP address for the LT260 beforehand so that a LAN environment can be set up during installation.
In addition, network devices and other items must be prepared so that the LT260 can be connected to a LAN for operation management.
15
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Installation & Operation-
Copyright 2015 FUJITSU LIMITED P3AM-8792-04ENZ0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Cover
- 3 Preface
- 4 About this Manual
- 7 Warning Labels and Manufacturer's Labels
- 8 Table of Contents
- 12 List of Figures
- 14 List of Tables
- 15 Chapter 1 Preparation
- 15 1.1 Host Connection
- 15 1.2 Connection to LAN for Operation Management
- 16 Chapter 2 Components
- 17 2.1 Module
- 19 2.2 Operator Panel
- 20 2.3 Magazine
- 21 2.4 Mailslot
- 22 2.5 Drive Module
- 22 2.5.1 Drive Module Back Panels
- 25 2.6 Robot Assembly
- 26 2.7 Library Controller
- 27 2.8 Tape Drive Unit
- 29 2.9 Power Supply Unit (PSU)
- 30 Chapter 3 Basic Operation
- 30 3.1 Powering On/Off
- 35 3.1.1 Points to Note when Turning On or Turning Off the LT260
- 35 3.1.2 Turning on the Server
- 36 3.2 Operator Panel Operation
- 36 3.2.1 Using the Library Main Screen
- 37 3.2.2 Logging into the Library
- 39 3.3 Loading and Ejecting Cartridges
- 39 3.3.1 Opening the Mailslot
- 41 3.3.2 Opening a Magazine
- 42 3.3.3 Inserting Tape Cartridges
- 44 3.4 Cleaning Drives
- 44 3.4.1 Cleaning Drives Automatically
- 45 3.4.2 Cleaning Drives Manually
- 46 Chapter 4 Default Setting
- 47 4.1 Network Settings
- 49 4.2 Configuring the Date and Time Format
- 49 4.2.1 Setting the Time Zone
- 50 4.2.2 Setting the Date and Time Format
- 51 4.2.3 Setting the Date and Time
- 52 4.2.4 Enabling Simple Network Time Protocol (SNTP) Synchronization
- 53 4.3 Configuring Passwords for User Accounts
- 54 Chapter 5 Monitoring the LT260 Status
- 54 5.1 Status LEDs
- 54 5.2 Operator Panel and Remote Panel
- 55 5.2.1 Top Banner Elements
- 56 5.2.2 Left Pane Elements
- 57 5.2.3 Center Pane Elements
- 58 5.3 Configuring Event Notification Parameters
- 60 5.4 Fault Monitoring (SNMP Report Function)
- 61 Chapter 6 Function Expansion Option
- 61 6.1 License Partitioning Option (Logical Library Function)
- 63 6.1.1 Function Overview
- 63 6.1.2 Hardware Configuration
- 66 6.1.3 Designing Logical Libraries
- 67 6.1.4 Configuring Logical Libraries
- 71 6.2 Key Management Function Option
- 71 6.2.1 Overview
- 72 6.2.2 Features of the Key Management Function Option
- 73 6.2.3 Types of Key
- 74 6.2.4 Operational Examples
- 77 6.2.5 Connectivity with Backup Software
- 78 Chapter 7 Troubleshooting
- 78 7.1 Fibre Channel Connection Problems
- 79 7.2 Detection Problems after Installing a SAS Drive
- 81 7.3 Operation Problems
- 81 7.3.1 Power Problems
- 82 7.3.2 Failure/Attention Indications Displayed on the Operator Panel
- 82 7.3.3 Tape Movement Problems
- 83 7.3.4 Media Problems
- 84 7.3.5 Attention LED is Lit
- 85 7.3.6 Inventory Problems
- 85 7.3.7 Remote Panel Network Connection Issues
- 85 7.3.8 Cleaning Problems
- 86 7.4 Performance Problems
- 86 7.4.1 Average File Size
- 86 7.4.2 File Storage System
- 87 7.4.3 Connection from the Backup/Archive Host Server to the Disk Storage System
- 87 7.4.4 Backup/Archive Server
- 87 7.4.5 Backup/Archive Software and Method
- 87 7.4.6 Connection from the Archive/Backup Host Server to the Library
- 88 7.4.7 Media
- 89 7.5 Finding Event Information
- 90 7.6 Unlocking the Magazine
- 90 7.6.1 Using the Operator Panel
- 91 7.6.2 Using the Remote Panel
- 93 7.6.3 Using the Manual Release
- 94 7.7 Unloading a Stuck Tape
- 95 7.8 Identifying a Failed Component
- 96 7.9 Returning the Robot Assembly to the Base Module
- 97 7.10 Running Library Tests
- 98 Appendix A Tape Cartridge and Barcode Label Specifications
- 98 A.1 Ultrium Tape Cartridge
- 98 A.1.1 Tape Cartridge Specifications
- 99 A.1.2 Tape Drive Compatibility with Tape Cartridges
- 99 A.1.3 Notes Regarding the Use of Tape Cartridges
- 100 A.1.4 Handling Tape Cartridges
- 105 A.2 Barcode Labels
- 105 A.2.1 Barcode Label Specifications
- 107 A.2.2 Notes on Affixing a Barcode Label
- 108 Colophon