advertisement
▼
Scroll to page 2
of
224
About this Manual
The SDM-E2 Docking Station PC Controlled Configuration Operator’s Manual uses the following conventions for notes, cautions, and warnings.
NOTE:
Describes additional or critical information.
CAUTION:
Describes potential damage to equipment.
WARNING: Describes potential danger that can result in injury or death.
Cautions & Safety Information
• Use only polyurethane sample tubing with the SDM-E2. Consult RKI
Instruments, Inc. for other materials.
• Do not subject the SDM-E2 to infrared or intense light. This may cause communication errors.
• Do not expose the SDM-E2 to water.
• Do not subject the SDM-E2 to any hard impact.
About this Manual • 4
advertisement
Related manuals
advertisement
Table of contents
- 6 Introduction
- 7 System Requirements
- 8 Specifications
- 9 About This Manual
- 9 Cautions & Safety Information
- 10 Description
- 10 AC Adapter
- 10 Single-Port AC Adapter
- 10 3-Port AC Adapter
- 11 USB Cable
- 11 Air Filter, Sample Tubing, and Check Valve
- 12 Instrument Panel
- 13 Back Panel
- 13 Power Jack
- 13 Sample Fittings
- 13 PC Connection
- 14 Control Panel
- 15 Front Panel
- 16 Hardware Setup
- 16 Hardware Assembly
- 17 Assembling a Manifold for Multiple SDM-E2 Units
- 18 Exhaust Tubing
- 20 GAS 1 Tubing
- 20 GAS 2 Tubing
- 24 Connecting Calibration Gas
- 26 EAGLE 2 and GX Type Instrument Connection
- 26 Installing the SDM-E2 Docking Station PC Controller Program
- 32 Launching the SDM-E2 Docking Station PC Controller Program
- 33 Overview of the SDM-E2 Docking Station PC Controller Program
- 33 PC Controller Program Functions
- 34 Main Program Window
- 34 Control Buttons
- 34 SDM-E2/EAGLE 2 Display Area
- 35 Program Status
- 35 Fitting Indicators
- 35 Setting Up the PC Controller Program
- 35 Setting Up the Configuration
- 40 Setting Up the SDM-E2 Display Order
- 42 Cylinders Window
- 43 Selecting a Cylinder from the Pre-Defined List
- 44 Defining New Cylinders
- 45 Connecting Instruments to the PC Controller Program
- 49 Icon View vs. Details View
- 51 Exporting an Instrument List from the Main Program Window
- 52 Instrument Placement for Bump Testing and Calibration
- 54 Automatic Bump Testing and Calibration
- 55 Bump Testing a Standard 4-Gas Instrument
- 66 Calibrating a Standard 4-Gas Instrument
- 76 Bump Testing an Instrument with Special Sensors
- 92 Calibrating and Instrument with Special Sensors
- 107 Troubleshooting
- 108 Charging an Instrument in an SDM-E
- 108 Recharging a Battery Pack After Performing a Bump Test or Calibration
- 109 Recharging a Battery Pack Without Performing any Operations
- 110 Batteries Too Drained for PC Controller Operation
- 111 Logs Button
- 115 Alarm Trend Data
- 123 Calibration Data
- 125 Event Data
- 127 Interval Trend Data
- 137 Memo Data
- 139 Bump Test Data
- 143 Deleting Data in the Logs Window
- 144 Instrument Function Menu
- 144 Open Function
- 145 Edit Function
- 145 Parameter Tab
- 152 Sensor Tab
- 153 Station & User Tab
- 159 Conversion Table Tab
- 163 PID Sensor Tab
- 169 Channel Gas Tab
- 170 Gas Name Tab
- 170 Download Function
- 170 Clear Logs Function
- 171 Power Off Function
- 171 Obtaining a Relative Response Factor
- 182 Config Window
- 182 Parameter Tab
- 183 Database Tab
- 185 Password Tab
- 186 Spare Parts List
- 190 Appendix A: Multiple Instrument Configurations
- 190 Bump Testing Multiple EAGLE 2s with Different Sensor Configurations
- 207 Calibrating Multiple EAGLE 2s with Different Sensor Configurations
- 223 Appendix B: Bump Testing and Calibrating EAGLE 2s with IR Sensors