advertisement
CHDBT-1H7CE
1×8 HDMI over HDMI and CAT5e/6/7 Splitter with PoE and LAN Serving
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document.
Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 September 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 26/06/13 Preliminary Release
VS1 23/12/13 Updated Text & Diagrams
CONTENTS
1. Introduction ............................................ 1
2. Applications ........................................... 1
3. Package Contents ................................ 1
4. System Requirements ............................ 2
5. Features .................................................. 2
6. Operation Controls and Functions ....... 3
6.1 Front Panel .........................................3
6.2 Rear Panel .........................................3
6.3 IR Cable Pin Assignment ..................5
7. Connection Diagram ........................... 6
8. Specifications ........................................ 7
8.1 Technical Specifications ..................7
8.2 CAT5e/6/7 Cable Specification ......8
9. Acronyms ............................................... 8
1. INTRODUCTION
The HDMI over HDMI CAT5e/6/7 Splitter can split and distribute a single HDMI input, 2-way IR control and LAN serving to up to seven
CAT5e/6/7 outputs and includes a simultaneous HDMI bypass output.
It supports resolutions up to 1080p Full HD, 4K×2K timing, 3D and multichannel digital audio formats (such as LPCM 7.1CH, Dolby TrueHD,
Dolby Digital Plus and DTS-HD). The HDMI bypass output can be connected to an HDMI display or cascaded to another splitter. The
CAT5e/6/7 outputs can be connected to CAT5e/6/7 to HDMI receivers to extend the operating distance up to 100 meters.
Additionally, the LAN connectivity will allow a 100BaseT network to be served to smart TVs or games consoles. The Power over Ethernet (PoE) function can power compatible receivers, providing greater flexibility in installations.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×1 by 8 HDMI over HDMI and CAT5e/6/7 Splitter
• 1×IR Receiver
• 1×IR Blaster
• 24V DC Power Adaptor
• Power Cord
• Operation Manual
1
4. SYSTEM REQUIREMENTS
• HDMI equipped source devices, connect with HDMI cables
• HDMI equipped displays (TVs or monitors) or HDMI equipped AV receivers, connect with HDMI cables
• Certified CAT5e/6/7 cables
• HDBaseT™ Receivers (e.g. CH-507RX or CH-1109RX)
5. FEATURES
• HDMI with 4K×2K resolution and 3D support, HDCP and DVI compliant
• Simultaneous HDMI and CAT5e/6/7 outputs
• Supports one HDTV and seven CAT5e/6/7 outputs
• Supports data rate from 300 Mbps up to 3 Gbps
• Supports a wide range of PC resolutions from VGA to WUXGA
(RB) and HDTV resolutions up to 4K×2K (3840×2160@30 Hz and
4096×2160@24 Hz)
• Supports transmission of High Definition audio: LPCM 7.1CH, Dolby
TrueHD, Dolby Digital Plus and DTS-HD Master Audio (32 kHz~192 kHz sample rate)
• Supports distances up to 100 meters over CAT5e/6/7 cables
• Supports Ethernet network rates up to 100Mbps
• Supports PoE with compatible Receiver units
• Supports selection of Standard or TV EDID settings
• Supports control of devices via 2-way IR
• 3D signal display is dependent on the TV/Display’s EDID settings
Note:
1. This system was tested with CAT6/23AWG cables, results may vary with cables of a different specification.
2. The PoE function is designed for powering compatible Receiver units only, non-PoE Receivers will need their own power supply.
Receivers of another brand may not be compatible.
3. For playback of 4k×2k HDMI source signals, a 4K×2K capable
display and High Speed HDMI cables are required.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER SYNC
HDMI
LINK LINK 1 LINK 2 LINK 3
CAT5e/ 6 / 7 OUT
LINK 4 LINK 5 LINK 6 LINK 7
1 2 3 4
1 POWER LED: The LED will illuminate when connected to an active power supply.
2 SYNC LED: This LED will illuminate when the HDMI input is connected to a HDMI source and receiving a signal.
3 HDMI OUT LINK LED: This LED will illuminate when HDMI output is connected to TV or display monitor and receiving a signal.
4 CAT5e/6/7 OUT LINK 1~7 LEDs: The link LEDs will illuminate when the receivers are connected to the CAT 5e/6/7 outputs are connected to TVs or displays and displaying a signal.
6.2 Rear Panel
HDMI IN HDMI OUT 1 2 3
CAT5e/ 6 / 7 OUT
4 5 6 7 LAN IR IN IR OUT
4 5 6
DC 24V
EDID SERVICE
STD TV
7 8 9 1 2 3
1 HDMI IN: Connect to HDMI equipped source equipment such as a
DVD/Blu-ray player or games console.
2 HDMI OUT: Connect to a HDMI display for local monitoring of the
HDMI signal or cascade to another Splitter.
3 CAT5e/6/7 OUT 1~7: Connect to CAT5e/6/7 to HDMI Receivers (with or without PoE) with a single CAT5e/6/7 cable each to extend the
HDMI signal up to 100 m.
4 LAN: Connect to an active network for LAN serving. When any compatible LAN equipped receivers are connected, this allows the network access (including internet access if available) to be shared. Connect any Ethernet equipped device e.g. a Smart TV
3
or games console to the LAN port of a receiver for that device to share the network/internet access.
Warning: DO NOT connect the LAN connection with any of the
CAT5e/6/7 outputs, doing so may trigger a power shut down and may damage the device.
5 IR IN: Connect the supplied IR Receiver cable for IR signal reception. Ensure that remote being used is within the direct lineof-sight of the IR Extender.
6 IR OUT: Connect the supplied IR Blaster cable for IR signal transmission. Place the IR Blaster in direct line-of-sight of the equipment to be controlled.
7 EDID STD/TV: The default setting is TV, when in this mode, the unit will detect the EDID settings of the display device connected to the CAT 5e/6/7 Output 1. If it detects a 4K×2K capable EDID setting it will transmit the signal in that format to the output port. If no 4K×2K capable EDID is detected then the unit will detect the EDID settings and send out the signal that all outputs can accept.
This device has a last memory function and will retain the EDID settings of the last device connected via the CAT5e/6/7 output port when it is not connected to a display after power cycling.
Switch to the STD setting to use the unit's built-in EDID if there are display problems. In this mode, the video output will be set to
1080p@60Hz and the audio at LPCM 2CH Stereo.
8 SERVICE: Reserved for manufacturer use only.
9 DC 24V: Connect the 24V DC power supply to the unit and plug the adaptor into an AC outlet.
4
6.3 IR Cable Pin Assignment
IR Blaster
1
2
3
Power 3.3 V
IR Blaster Signal
NC
IR Extender
1
2
3
IR Signal
Power 3.3 V
Ground
5
7. CONNECTION DIAGRAM
Local Display
Blu-ray Player
Router
(with Internet Connection)
HDMI
Input
HDMI IN HDMI OUT 1 2 3
CAT5e/ 6 / 7 OUT
4 5 6 7 LAN IR IN IR OUT
EDID SERVICE
STD TV
DC 24V
Power
Supply
HDMI
Output
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
CAT 5e/6/7
Outputs
(PoE for
Compatible
Receivers)
Power
IR2 Blaster
IR1 Extender
Link
CAT5e/6 In
RX
HDMI Outputs
IR Out/In
LAN Serving
Smart
TVs
3m
60°
3m
1.5m
60°
IR RECEIVER IR BLASTER
6
8. SPECIFICATIONS
8.1 Technical Specifications
Video Bandwidth
Input Ports
340 Mbps/10.2 Gbps
1×HDMI, 1×LAN, 1×IR IN, 1×USB (Service only)
1×HDMI, 7×CAT5e/6/7, 1×IR OUT Output Ports
HDMI Supported
Resolutions
480i~1080p@50/60 Hz, 1080p@24 Hz, 4K×2K
(3840×2160@30 Hz/4096×2160@24/25Hz) &
VGA~WUXGA (RB)
10m (1080p@8/12-bit), 10m (4K×2K) HDMI Input
Cable Distance
HDMI Output
Cable Distance
IR Frequency
Power Supply
Dimensions
Weight
Chassis Material
15m (1080p@8-bit), 10m (1080p@12-bit),
10m (4K×2K)
30~50 kHz
24 V/6.25 A DC (US/EU standards, CE/FCC/
UL certified)
432 mm(W)×178 mm(D)×49 mm(H)
2140 g
Metal
Color
ESD Protection
Black
Human body model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Operating Temperature 0 °C ~ 40 °C
Storage Temperature
Relative Humidity
Power Consumption
−20 °C ~ 60 °C / −4 °F ~ 140 °F
20 ~ 90 % RH (non-condensing)
85 W
7
8.2 CAT5e/6/7 Cable Specification
CABLE
TYPE
RANGE PIXEL
CLOCK
VIDEO
DATA
RATE RATE
CAT5e/6/7 100 m ≤225 MHz ≤5.3 Gbps
(HD Video)
70 m >225 MHz > 5.3 Gbps
(Ultra HD
Video)
SUPPORTED
VIDEO
Up to 1080p, 60 Hz, 36 bits, 3D (data rates lower than 5.3 Gbps or below 225MHz
TMDS clock)
4Kx2K, 30Hz video formats
9. ACRONYMS
ACRONYM
4Kx2K
DTS
EDID
HDCP
HDMI
HDTV
COMPLETE TERM
Ultra High-Definition (3840×2160/4096×2160)
Digital Theater System
Extended Display Identification Data
High-bandwidth Digital Content Protection
High-Definition Multimedia Interface
High-Definition Television
8
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20130531MPM-CHDBT-1H7CE
advertisement
Related manuals
advertisement