PowerView
™
Rev 09-10-08
Model PV-101
User’s Guide
00-02-0605
78
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.
Warranty
- A limited warranty on materials and workmanship is given with this FW Murphy product. A copy of the warranty may be viewed or printed by going to www.fwmurphy.com/support/warranty.htm
BEFORE BEGINNING INSTALLATION OF THIS
MURPHY PRODUCT:
• Disconnect all electrical power to the machine.
• Make sure the machine cannot operate during installation.
• Follow all safety warnings of the machine manufacturer.
• Read and follow all installation instructions.
Table of Contents
Introduction ............................................................................. 1
Engine and Transmission Parameters 2
Faceplate Features
Navigation and Keypad Functions
3
4
Operation ................................................................................. 9
PowerView Menus (First Time Start Up) 9
Setting Up the Display
Main Menu Options
12
18
Faults and Warnings
Utilities Menu
Modbus
® Setup
Selecting Engine ECU
20
23
25
26
Troubleshooting ................................................................... 27
(THIS PAGE INTENTIONALLY LEFT BLANK)
Introduction
Congratulations on purchasing your PowerView display, a multifunction tool that provides a window into the many parameters and service codes of modern electronic engines and transmissions.
This guide is intended to help you set up your PowerView display and identify navigation basics and product features.
The display’s simple navigation and intuitive yet powerful features allow you to master the product in no time.
Additional information can be found on our website at www.fwmurphy.com/powerview.
00-02-0605 - 1 - Rev 09-10-08
Engine and Transmission Parameters
The following are some of the engine and transmission parameters which may be displayed in standard or metric units as well as in English, Spanish, French, Italian, or
German languages (when applicable, consult engine or transmission manufacturer for SAE J1939 supported parameters):
RPM
• Engine voltage
• Percent engine load at the current RPM temperature pressure
• Fuel position
• Engine manifold air temperature
• Current fuel consumption pressure oil temperature gear position configuration parameters
• Active fault codes
• Stored fault codes
00-02-0605 - 2 - Rev 09-10-08
Faceplate Features
00-02-0605 - 3 - Rev 09-10-08
Navigation and Keypad Functions
The keypad on the PowerView display is a capacitive touch sensing system. There are no mechanical switches to wear or stick. When a key is touched, feedback is provided by the screen flashing. The keys on the keypad perform the following functions:
Menu – Enter or exit menu screens.
Left Arrow – Scroll the screen or move the parameter selection to the left or upward.
Right Arrow – Scroll the screen and move the parameter selection to the right or downward.
Enter Key – Select a menu or parameter or hide/view an active fault code.
00-02-0605 - 4 - Rev 09-10-08
Basic Navigation
displayed.
00-02-0605 - 5 - Rev 09-10-08
other menu items.
00-02-0605 - 6 - Rev 09-10-08
3. Certain menus have multiple pages of items. Scrolling past the top item or bottom item on the current page will reveal other menu items on additional pages.
00-02-0605 - 7 - Rev 09-10-08
4. When the desired item is highlighted by the cursor, pressing Enter will select that item and display the corresponding screen.
5. Anytime the word MORE appears above the Arrow
Keys there are more screens that may be viewed. Use the Arrow Keys to scroll to the next screen of information.
00-02-0605 - 8 - Rev 09-10-08
Operation
PowerView Menus (First Time Start Up)
1. When power is first applied to the display, the Murphy logo appears.
00-02-0605 - 9 - Rev 09-10-08
2. If the Engine ECU is broadcasting a 'Wait To Start' message, this screen will be shown. Engine manufacturers typically recommend against starting the engine while this message is broadcasted from the
ECU. Once the ECU stops broadcasting this message, this screen will no longer be displayed.
00-02-0605 - 10 - Rev 09-10-08
3. Once the engine has started, the single engine parameter appears with the engine RPM displayed.
Pressing the Right Arrow Key will display the coolant temperature. The screen can be changed to other parameters by pressing Menu.
00-02-0605 - 11 - Rev 09-10-08
Setting Up the Display
The screen may be configured to display a single engine parameter (1-up display), or four parameters at once (4-up display). Default options are provided or you may customize the display by selecting the parameters you want.
1-Up Display
Three options are available for modification of the 1-Up display.
Use Defaults – This option contains a set of engine parameters: Engine Hours, Engine RPM, System Voltage,
Battery Voltage, % Engine Load at Current RPM, Coolant
Temperature, and Oil Pressure.
Custom Setup – This option allows for the modification of which parameter, the number of parameters, and the order in which the parameters are being displayed.
Automatic Scan – Selecting the scan function will cause the 1-Up Display to scroll through the selected set of parameters one at a time, momentarily pausing at each.
00-02-0605 - 12 - Rev 09-10-08
1-Up Display Settings
SETUP 1-UP DISPLAY, then press Enter.
2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO
DEFAULTS” is displayed.
3. To select CUSTOM SETUP, highlight the option and press Enter. A list of engine parameters is displayed.
4. To select a parameter, use the Arrow Keys to scroll and highlight the parameter, then touch Enter.
Selected parameters are indicated by a # symbol to the right of it and represent the order in which the parameter will be displayed.
5. To deselect a selected parameter and remove it from the list of displayed parameters, highlight the parameter and touch Enter.
00-02-0605 - 13 - Rev 09-10-08
6. Continue to scroll and select additional parameters for the CUSTOM 1-UP DISPLAY. Touch Menu at any time to return to the CUSTOM SETUP menu. cause the 1-up display to scroll through the selected set of parameters one at a time.
8. Once the USE DEFAULTS, CUSTOM SETUP and
AUTOMATIC SCAN functions have been set, touch
Menu once to return to the main menu, or twice to display the 1-up display screen.
00-02-0605 - 14 - Rev 09-10-08
4-Up Display
The 4-up display places the parameter data into four areas of the screen known as quadrants. Factory defaults for the
4-up display include coolant temperature, engine speed, oil pressure, and battery voltage. You may customize the 4-up display with parameters you define for each quadrant.
SETUP 4-UP DISPLAY, then press Enter.
2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO
DEFAULTS” is displayed.
3. To select CUSTOM SETUP, highlight the option and press Enter. The 4-up display appears.
4. The quadrant with the backlit parameter value is the currently selected parameter. Use the Arrow Keys to select which quadrant you wish to edit.
00-02-0605 - 15 - Rev 09-10-08
The parameter that is highlighted is the selected parameter for the screen. The number to the right of the parameter indicates the quadrant in which it is displayed.
1 = upper left quadrant
2 = lower left quadrant
3 = upper right quadrant
4 = lower right quadrant be placed in the quadrant that was selected in step 4 and touch Enter. screen.
00-02-0605 - 16 - Rev 09-10-08
8. The parameter in the selected quadrant has changed to the parameter selected in the previous screen.
9. Repeat the parameter selection process until all spaces are filled.
00-02-0605 - 17 - Rev 09-10-08
Main Menu Options
This section describes the features listed on the main menu of the PowerView. These menu options are displayed whenever you touch Menu. The Arrow Keys allow you to scroll the items, and Enter selects the highlighted option.
Selecting a Language
From LANGUAGES, you may select ENGLISH, ESPANOL,
FRANCAIS, ITALIANO, or DEUTSCH. The currently selected language is indicated by an asterisk.
Stored Fault Codes*
Request stored fault code information.
Engine Configuration Data*
ENGINE CONFG allows you to scroll through engine configuration data.
* This function may not be supported by all manufacturers.
00-02-0605 - 18 - Rev 09-10-08
Backlight Adjustment
ADJUST BACKLIGHT allows you to select the desired backlight intensity.
Contrast Adjustment
From ADJUST CONTRAST, you may select the desired contrast intensity.
Select Units
From SELECT UNITS, you may select how information is displayed. ENGLISH for Imperial units, i.e., PSI,
°F or
METRIC KPA, METRIC BAR for IS units, i.e., kPa, Bar,
°C.
Utilities
UTILITIES provide troubleshooting features and displays information about the PowerView configuration. (See
“Utilities Menu”)
00-02-0605 - 19 - Rev 09-10-08
Faults and Warnings
The PowerView provides two means for detecting faults and warnings: visual LEDs on the casing (See “Faceplate
Features”) and fault indicators on the display.
Visual Indication
• Amber LED (Warning)
• Red LED (Derate / Shutdown)
Fault Indicators
00-02-0605 - 20 - Rev 09-10-08
Auxiliary Gage Fault
Murphy’s PVA Gages can be attached to the PowerView. If an auxiliary gage should fail, the 1-up or 4-up display will be replaced with the fault message “GAGE NOT
RESPONDING”.
NOTE: The fault can only be cleared by correcting the cause of the fault condition.
Active Fault Codes
When the PowerView receives a fault code from an engine, the 1-up or 4-up display will be replaced with the active fault codes message.
Derate / Shutdown Codes
When the PowerView receives a severe fault code from an engine control unit the 1-up or 4-up display will be replaced with the SHUTDOWN message.
00-02-0605 - 21 - Rev 09-10-08
Acknowledging Fault Codes
1. To acknowledge and hide the fault and return to the
1-up or 4-up display, touch Enter. The display will return to the 1-up or 4-up display, but the display will contain the shutdown icon. once again will hide the fault and return the screen to the 1-up or 4-up display.
00-02-0605 - 22 - Rev 09-10-08
Utilities Menu
The following steps take place starting at the UTILITIES menu option.
1. GAGE DATA - View information for optional connected
PVA gages.
2. REMOVE ALL GAGES - Reset the PowerView's gage memory.
3. SOFTWARE VERSION - View the PowerView's software version.
4. MODBUS SETUP – refer to ‘Modbus Setup’ section.
5. FAULT CODE CONVERSION - View/edit the J1939 fault code conversion method.
NOTE: There are four (4) different methods for converting fault codes. The PowerView always looks for
J1939 Version 4 and can be set to read the code as one of three (3) other J1939 versions if Version 4 is not
00-02-0605 - 23 - Rev 09-10-08
being used. Most engine ECU’s use Version 4, therefore in most cases adjustment of this menu option will not be required.
Upon receiving an unrecognizable fault, change to a different J1939 Version. If the fault SPN does not change when the version is changed, the ECU generating the fault is using Fault Conversion method 4.
If the SPN number does change but is still unrecognizable, try changing to another J1939 Version not yet used and continue to check the SPN number.
6. ANALOG INPUT – provides two setting options:
• BACKLIGHT DIMMER, the default setting, will accept an optional backlighting dimmer.
• FUEL LEVEL accepts an optional Murphy fuel sender (model ES2F recommended) for fuel level information.
7. SELECT ENGINE ECU – listens to all ECUs or scrolls to a specific engine ECU.
00-02-0605 - 24 - Rev 09-10-08
Modbus
® Setup
1. From the UTILITIES menu, select MODBUS SETUP.
2. Select either the SLAVE ACTIVE (SCADA or remote
Modbus master) or MASTER ACTIVE (auxiliary gages) modes. Touch Enter to toggle between master and slave.
3. Select SERIAL PORT SETUP (slave mode only), then touch Enter.
4. Continue to scroll each selection (BAUD RATE,
PARITY, DATA BITS, STOP BITS) to configure the serial port parameters for your Modbus slave application.
00-02-0605 - 25 - Rev 09-10-08
Selecting Engine ECU
1. From the UTILITIES menu, choose SELECT ENGINE
ECU.
2. The message “LISTEN TO ECU: ALL” is displayed as the default setting, and indicates the PV101 is listening to all devices on the network.
3. To change the setting to a specific address, press the
Arrow Keys to scroll through the numbers (0-253).
4. Once the target address is displayed, press Enter.
5. A confirmation screen displays. Selecting “NO” (shown above Menu key) returns to the SELECT ENGINE ECU screen. Selecting “YES” (shown above Enter key) stores the selected address and returns to the
UTILITIES menu.
00-02-0605 - 26 - Rev 09-10-08
Troubleshooting
“WAIT TO START PREHEATING” is displayed
The ECU is broadcasting a 'Wait To Start' message. Engine manufacturers typically recommend against starting the engine while the ECU is broadcasting this message. Once the ECU stops broadcasting this message, this screen will no longer be displayed on the PowerView.
“CANBUS FAILURE” is displayed
The PowerView has not received any valid J1939 CAN messages for at least 30 seconds.
“TIMEOUT ECU NOT RESPONDING” is displayed
The PowerView sent a request to the ECU for Stored Fault
Code (DM2) information, and the ECU did not respond to the request. This message on the PowerView indicates the
ECU may not support Stored Fault Code (DM2) functionality over J1939.
00-02-0605 - 27 - Rev 09-10-08
“NO STORED CODES” is displayed
The PowerView sent a request to the ECU for Stored Fault
Code (DM2) information, and the ECU responded. There are zero stored codes.
“NO GAGE DATA” is displayed
The PowerView has no record of gages connected to the
RS485 bus.
“NO DATA” is displayed in place of a parameter value
The PowerView has not received data for the selected parameter for at least 5 seconds.
“NOT SUPPORTED” is displayed in place of a parameter value
The ECU is sending a message that it does not support this parameter.
00-02-0605 - 28 - Rev 09-10-08
“DATA ERROR” is displayed in place of a parameter value
The ECU is sending a message that there is a data error with this parameter. Or (PV101 only) FUEL LEVEL has been selected for display, ANALOG INPUT has been set to
FUEL LEVEL, but no Murphy Fuel Sender has been connected to the analog input.
One of the 4-UP quadrants is empty
No parameter has been selected for display in this quadrant.
Display is not readable, either very dim or very dark
The LCD contrast may have been over or under adjusted.
Press and hold the MENU key for approximately 5 seconds. This will reset the LCD contrast setting to factory default.
00-02-0605 - 29 - Rev 09-10-08
NOTES
00-02-0605 - 30 - Rev 09-10-08
Murphy, the Murphy logo, and PowerView are registered and/or common law trademarks of Murphy Industries, Inc. This document, including textual matter and illustrations, is copyright protected by
Murphy Industries, Inc., with all rights reserved. (c) 2008 Murphy
Industries, Inc. Other third party product or trade names referenced herein are the property of their respective owners and are used for identification purposes only.
www.fwmurphy.com/PV101
