Murphy PowerView PV-101-A Engine Display User's Guide

PowerView



Model PV-101-A, V2.3

User’s Guide

78

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.

Warranty

- A limited warranty on materials and workmanship is given with this FW Murphy product. A copy of the warranty may be viewed or printed by going to www.fwmurphy.com/support/warranty.htm

BEFORE BEGINNING INSTALLATION OF THIS

MURPHY PRODUCT:

 Disconnect all electrical power to the machine.

 Make sure the machine cannot operate during installation.

 Follow all safety warnings of the machine manufacturer.

 Read and follow all installation instructions.

Table of Contents

Table of Contents ................................................................... 3  

Introduction ............................................................................. 1  

Engine and Transmission Parameters

Faceplate Features

Navigation and Keypad Functions 4  

Operation ................................................................................. 9  

2  

3  

PowerView Menus (First Time Start Up)

Setting up the Display

Main Menu Options

Utilities Menu

9

12

18  

22  

OEM Menu ............................................................................. 26  

 

 

MODBUS  Setup

CANBUS Data Rate

Select Engine ECU

26  

27  

27  

Set Source Address

Restore All Defaults

Clear Machine Hours

Set Machine Hours

28  

29  

29  

29  

Faults and Warnings 31  

Troubleshooting 34  

Introduction

Congratulations on purchasing your PowerView display, a multifunction tool that provides a window into the many parameters and service codes of modern electronic engines and transmissions.

This guide is intended to help you set up your PowerView display and identify navigation basics and product features.

The display’s simple navigation and intuitive yet powerful features allow you to master the product in no time.

Additional information can be found on our website at www.fwmurphy.com/powerview.

00-02-0795 - 1 - 10-18-11

Engine and Transmission Parameters

The following are some of the engine and transmission parameters which may be displayed in standard or metric units as well as in English, Spanish, French, Italian, or

German languages (when applicable, consult engine or transmission manufacturer for SAE J1939 supported parameters):

RPM

 Engine voltage

 Percent engine load at the current RPM temperature pressure

 Fuel position

 Engine manifold air temperature

 Current fuel consumption pressure oil temperature gear position

 Engine parameters

 Active fault codes

 Stored fault codes

00-02-0795 - 2 - 10-18-11

Faceplate Features

00-02-0795 - 3 - 10-18-11

Navigation and Keypad Functions

The keypad on the PowerView display is a capacitive touch sensing system. There are no mechanical switches to wear or stick. The keys on the keypad perform the following functions:

Menu – Enter or exit menu screens.

Left Arrow – Scroll the screen or move the parameter selection to the left or upward.

Right Arrow – Scroll the screen and move the parameter selection to the right or downward.

Enter Key – Select a menu or parameter or hide/view an active fault code.

00-02-0795 - 4 - 10-18-11

Basic Navigation

Menu is pressed, the main menu items are displayed.

00-02-0795 - 5 - 10-18-11

the other menu items.

00-02-0795 - 6 - 10-18-11

3. Certain menus have multiple pages of items. Scrolling past the top item or bottom item on the current page will reveal other menu items on additional pages.

00-02-0795 - 7 - 10-18-11

4. When the desired item is highlighted by the cursor, pressing Enter will select that item and display the corresponding screen.

5. Anytime the word NEXT appears above the Arrow

Keys there are more screens that may be viewed. Use the Arrow Keys to scroll to the next screen of information.

00-02-0795 - 8 - 10-18-11

Operation

PowerView Menus (First Time Start Up)

1. When power is first applied to the display, the Murphy logo appears.

00-02-0795 - 9 - 10-18-11

2. If the Engine ECU is broadcasting a 'Wait to Start' message, this screen will be shown. Engine manufacturers typically recommend against starting the engine while this message is broadcast from the ECU.

Once the ECU stops broadcasting this message, this screen will no longer be displayed.

3. Once the engine has started, the single engine parameter appears with the engine RPM displayed.

00-02-0795 - 10 - 10-18-11

Pressing the Right Arrow Key will display the coolant temperature. The screen can be changed to other parameters by pressing Menu.

00-02-0795 - 11 - 10-18-11

Setting up the Display

The screen may be configured to display a single engine parameter (1-up display), or four parameters at once (4-up display). Default options are provided or you may customize the display by selecting the parameters you want.

1-Up Display

Three options are available for modification of the 1-Up display.

Use Defaults – This option contains a set of engine parameters: Engine Hours, Engine RPM, System Voltage,

Battery Voltage, % Engine Load at Current RPM, Coolant

Temperature, and Oil Pressure.

Custom Setup – This option allows for the modification of which parameter, the number of parameters, and the order in which the parameters are being displayed.

Automatic Scan – Selecting the scan function will cause the 1-Up Display to scroll through the selected set of parameters one at a time, momentarily pausing at each.

00-02-0795 - 12 - 10-18-11

1-Up Display Settings

Menu and use the Arrow Keys to highlight

SETUP 1-UP DISPLAY, then press Enter.

2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO

DEFAULTS” is displayed.

3. To select CUSTOM SETUP, highlight the option and press Enter. A list of engine parameters is displayed.

4. To select a parameter, use the Arrow Keys to scroll and highlight the parameter, then touch Enter.

Selected parameters are indicated by a # symbol to the right, and represent the order in which the parameter will be displayed.

5. To deselect a selected parameter and remove it from the list of displayed parameters, highlight the parameter and touch Enter.

00-02-0795 - 13 - 10-18-11

6. Continue to scroll and select additional parameters for the CUSTOM 1-UP DISPLAY. Touch Menu at any time to return to the CUSTOM SETUP menu. cause the 1-up display to scroll through the selected set of parameters one at a time.

8. Once the USE DEFAULTS, CUSTOM SETUP and

AUTOMATIC SCAN functions have been set, touch

Menu once to return to the main menu, or twice to display the 1-up display screen.

00-02-0795 - 14 - 10-18-11

4-Up Display

The 4-up display places the parameter data into four areas of the screen known as quadrants. Factory defaults for the

4-up display include coolant temperature, engine speed, oil pressure, and battery voltage. You may customize the 4-up display with parameters you define for each quadrant.

Menu and use the Arrow Keys to highlight

SETUP 4-UP DISPLAY, then press Enter.

2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO

DEFAULTS” is displayed.

3. To select CUSTOM SETUP, highlight the option and press Enter. The 4-up display appears.

4. The quadrant with the backlit parameter value is the currently selected parameter. Use the Arrow Keys to select which quadrant you wish to edit.

00-02-0795 - 15 - 10-18-11

Enter and a list of parameters will appear.

The parameter that is highlighted is the selected parameter for the screen. The number to the right of the parameter indicates the quadrant in which it is displayed.

1 = upper left quadrant

2 = lower left quadrant

3 = upper right quadrant

4 = lower right quadrant be placed in the quadrant that was selected in step 4 and touch Enter.

Menu to return to the 4-UP CUSTOM SETUP screen.

00-02-0795 - 16 - 10-18-11

8. The parameter in the selected quadrant has changed to the parameter selected in the previous screen.

9. Repeat the parameter selection process until all spaces are filled.

00-02-0795 - 17 - 10-18-11

Main Menu Options

This section describes the features listed on the main menu of the PowerView. These menu options are displayed whenever you touch Menu. The Arrow Keys allow you to scroll the items, and Enter selects the highlighted option.

Selecting a Language

From LANGUAGES, you may select ENGLISH, ESPANOL,

FRANCAIS, ITALIANO, or DEUTSCH. The currently selected language is indicated by an asterisk.

Stored Fault Codes

Select this and PowerView requests and displays stored fault codes from the engine ECU. If the engine does not support this function, a “Timeout ECU Not Responding” message displays.

Engine Configuration Data

This allows you to scroll through and view the engine’s configuration data. If the engine does not support this

00-02-0795 - 18 - 10-18-11

function, a “No Engine Configuration Data” message displays

Service Reminders

SERVICE REMINDERS permit you to RESET REMINDERS or MODIFY REMINDERS for changing engine oil, air filters, and hydraulic oil or for servicing the engine and/or machine.

NOTE: Service Reminders are internal reminders within

PowerView. Once a Service Reminder is active, warnings will show SPN 916 and FMI 17. Check PowerView Service

Reminders prior to calling Technical Support. the and touch Enter.

Service Reminders options display. Use the

Arrow Keys to select either Reset Reminders or

Modify Reminders, and then touch Enter.

3. If you select Reset Reminders, use the Arrow Keys to highlight the Reminder you wish to edit. Touch Enter.

00-02-0795 - 19 - 10-18-11

Reminder name appears at the top of the screen.

The action (ON or OFF) displays mid-screen, and two choices display at screen bottom. Touch Menu to

Cancel the action. Touch Enter to choose Reset.

5. If you select Modify Reminders, use the Arrow Keys to highlight the Reminder to modify and touch Enter.

Reminder name appears at top screen. The hour value displays mid-screen and allows you to set the number of hours to elapse before a Reminder prompts.

Bottom screen shows Cancel and Save. Touch Cancel to discard changes and return to Reminders list.

7. Use the right Arrow Key to increment the highlighted number. Use the left Arrow Key to move to the next number space.

Save. The Modify Service Reminder screen displays. Touch YES to save or NO to return to the

Reminders list.

00-02-0795 - 20 - 10-18-11

modified Reminder displays a (+) at right of

Reminder name when successfully completed. Follow the above steps to modify other Reminders.

When finished, touch Menu to return to the Main Menu.

Select Units

From SELECT UNITS, you may select how information is displayed:

▪ ENGLISH for Imperial units (PSI, F)

▪ METRIC KPA

▪ METRIC BAR for IS units (kPa, Bar, C).

Backlight Adjustment

ADJUST BACKLIGHT allows you to select the desired backlight intensity.

Contrast Adjustment

From ADJUST CONTRAST, you may select the desired contrast intensity.

00-02-0795 - 21 - 10-18-11

Utilities Menu

UTILITIES provide troubleshooting features and displays information about the PowerView configuration.

Gage Data

View information for optional connected PVA gages.

Remove All Gages

Reset the gage memory on the PowerView.

Software Version

This screen lists Configuration, Firmware, Languages, and

Bootloader versions for this PowerView unit. You may need this information if requesting assistance from Technical

Support.

00-02-0795 - 22 - 10-18-11

Modbus

 Setup

1. From the UTILITIES menu, select MODBUS

SETUP.

2. Select either the SLAVE ACTIVE (SCADA or remote Modbus master) or MASTER ACTIVE

(auxiliary gages) modes. Touch Enter to toggle between master and slave.

3. Select SERIAL PORT SETUP (slave mode only), then touch Enter.

4. Continue to scroll each selection (BAUD RATE,

PARITY, DATA BITS, and STOP BITS) to configure the serial port parameters for your Modbus slave application.

Fault Conversion

View and/or edit the J1939 fault code conversion method.

NOTE: There are four (4) different methods for converting

00-02-0795 - 23 - 10-18-11

fault codes. The PowerView always looks for J1939 Version

4 and can be set to read the code as one of three (3) other

J1939 versions if Version 4 is not being used. Most engine

ECU’s use Version 4, therefore in most cases adjustment of this menu option will not be required.

Upon receiving an unrecognizable fault, change to a different J1939 Version. If the fault SPN does not change when the version is changed, the ECU generating the fault is using Fault Conversion method 4. If the SPN number does change but is still unrecognizable, try changing to another J1939 Version not yet used and continue to check the SPN number.

Analog Input

With Analog Input highlighted, press Enter. You can select between two settings:

 BACKLIGHT DIMMER, this is in factory default upon first use. The unit accepts an optional backlighting dimmer (0-1k Ω potentiometer).

00-02-0795 - 24 - 10-18-11

 FUEL LEVEL, touch Enter to reach SET LOW

FUEL LEVEL screen. Then, touch Enter to reach

LOW FUEL % screen. Use the right Arrow Key to increase, and left Arrow Key to decrease the percentage of remaining fuel at which to send a warning. The default is 20%.

NOTE: The PowerView accepts optional Murphy fuel sender (recommend Model ES2F) for fuel level information. A custom setup for a non-Murphy fuel sender is available. For more information, see

FUEL SETPOINTS, page 30 (OEM Menu).This parameter provides two setting options.

00-02-0795 - 25 - 10-18-11

OEM Menu

The OEM menu is the last item on the Utilities menu. You must have a password to access the OEM menu. Once in the OEM Menu, select an item by highlighting it and touch

Enter to reach additional screens.

ENTER PASSWORD screen – Enter 3482 in the numeric spaces provided. Start at the furthest left numeric value and use the Left Arrow Key to increment the number and the

Right Arrow Key to move to the next numeric position.

The following items are in the OEM Menu.

MODBUS

 Setup

To set the MODBUS, highlight MODBUS SETUP and touch

Enter.

1) There are four selections: Use Factory Defaults,

Serial Port Setup, Slave Address Setup, and Master

Active/Slave Active. You can toggle between Slave

Active (which is SCADA/remote Modbus master)

00-02-0795 - 26 - 10-18-11

and Master Active (which is Auxiliary gages).

Highlight your selection and touch Enter.

2) If in Slave Active, select SERIAL PORT SETUP and touch Enter.

3) Scroll through the Serial Port Setup list and make selections for BAUD RATE, PARITY, DATA BITS, and STOP BITS to configure the serial port parameters for your Modbus slave application.

CANBUS Data Rate

Touch Enter to reach the six CANBUS data rates. Use the

Arrow Keys to highlight your choice and touch Enter to make the selection.

Select Engine ECU

Highlight Select Engine ECU and touch Enter.

00-02-0795 - 27 - 10-18-11

1) The message “LISTEN TO ECU: ALL” displays as the default setting. This message indicates the

PV101 is listening to all devices on the network.

2) To change the setting to a specific address, touch the Arrow Keys to scroll through the selections (0-

253, and ALL).

3) Once the target address displays, touch Enter.

4) A confirmation screen displays; selecting NO

(Menu) returns to the SELECT ENGINE ECU screen. Selecting YES (Enter) stores the selected address and returns to the OEM menu.

Set Source Address

Allows setting the source claim address for the PowerView on the CAN Network. Options are Auto Claim or 0 to 253.

00-02-0795 - 28 - 10-18-11

Restore All Defaults

PowerView automatically resets after the restore defaults is complete. RESTORING ALL FACTORY DEFAULTS displays when this is selected.

Clear Machine Hours

Use this to clear machine hours internal to PowerView outside of ECU hours.

Set Machine Hours

Machine hours calculate internally when the RPM is greater than 50 and the engine is not broadcasting hours. Use this if you want to track hours for just the machine.

00-02-0795 - 29 - 10-18-11

Fuel Setpoints

Highlight and touch Enter to select Fuel Setpoints.

Enter to turn Fuel Setpoints ON or OFF.

 Once in the Fuel Setpoint screen you can choose to set the Empty Setpoint, Set Fuel Setpoint, Show

Fuel Setpoints, Clear Fuel Setpoints, or choose to set the fuel setpoints for ¼, ½, and ¾ fuel tank levels.

Fuel Setpoints must be ON to work with a non-Murphy fuel sender. Modifying fuel setpoints is a complex process. To assist you in configuring for a Murphy Fuel Sender or programing for a non-Murphy Sender, go to the FW

Murphy Web site (www.fwmurphy.com/pv101), locate

PV101 Display and under the Literature tab, locate the document Fuel Sender Calibration.

00-02-0795 - 30 - 10-18-11

Faults and Warnings

The PowerView provides two means for detecting faults and warnings: visual LEDs on the casing (See “Faceplate

Features”) and fault indicators on the display.

Visual Indication

 Amber LED (Warning)

 Red LED (Derate / Shutdown)

Fault Indicators

00-02-0795 - 31 - 10-18-11

Auxiliary Gage Fault

Murphy’s PVA Gages can be attached to the PowerView. If an auxiliary gage should fail, the 1-up or 4-up display will be replaced with the fault message “GAGE NOT

RESPONDING”.

NOTE: The fault can only be cleared by correcting the cause of the fault condition.

Active Fault Codes

When the PowerView receives a fault code from an engine, the 1-up or 4-up display will be replaced with the active fault codes message.

Derate / Shutdown Codes

When the PowerView receives a severe fault code from an engine control unit the 1-up or 4-up display will be replaced with the SHUTDOWN message.

00-02-0795 - 32 - 10-18-11

Acknowledging Fault Codes

1. To acknowledge and hide the fault and return to the

1-up or 4-up display, touch Enter. The display will return to the 1-up or 4-up display, but the display will contain the shutdown icon.

Enter to redisplay the hidden fault. Touch Enter once again will hide the fault and return the screen to the 1-up or 4-up display.

00-02-0795 - 33 - 10-18-11

Troubleshooting

You may see the following messages displayed. Each gives you specific information about the engine, ECU, or

PowerView.

WAIT TO START PREHEATING - The ECU is broadcasting a 'Wait to Start' message. Engine manufacturers typically recommend against starting the engine while the ECU is broadcasting this message. Once the ECU stops broadcasting this message, this screen will no longer be displayed on the PowerView.

CANBUS FAILURE - The PowerView has not received any valid J1939 CAN messages for at least 30 seconds.

TIMEOUT ECU NOT RESPONDING - The PowerView sent a request to the ECU for Stored Fault Code (DM2) information, and the ECU did not respond to the request.

This message on the PowerView indicates the ECU may not support Stored Fault Code (DM2) functionality over

J1939.

00-02-0795 - 34 - 10-18-11

NO STORED CODES - The PowerView sent a request to the ECU for Stored Fault Code (DM2) information, and the

ECU responded. There are zero stored codes.

NO GAGE DATA - The PowerView has no record of gages connected to the RS485 bus.

The following messages are displayed in place of a parameter value

NO DATA - The PowerView has not received data for the selected parameter for at least 5 seconds.

NOT SUPPORTED - The ECU is sending a message that it does not support this parameter.

DATA ERROR - The ECU is sending a message that there is a data error with this parameter. If not, then specifically on the PV101, FUEL LEVEL has been selected for display, and the ANALOG INPUT has been set to FUEL LEVEL, but no Murphy Fuel Sender has been connected to the analog input.

00-02-0795 - 35 - 10-18-11

The following messages concern information about the

PV101.

One of the 4-UP quadrants is empty - No parameter has been selected for display in this quadrant.

Display is not readable, either very dim or very dark - The

LCD contrast may have been over or under adjusted. Press and hold the MENU key for approximately 5 seconds. This will reset the LCD contrast setting to factory default.

00-02-0795 - 36 - 10-18-11

NOTES

00-02-0795 - 37 - 10-18-11

Murphy, the Murphy logo, and PowerView are registered and/or common law trademarks of Murphy Industries, LLC. This document, including textual matter and illustrations, is copyright protected by Murphy Industries, Inc., with all rights reserved.

© 2011 Murphy Industries, LLC. Other third party product or trade names referenced herein are the property of their respective owners and are used for identification purposes only.

00-02-0795 www.fwmurphy.com/PV101

- 38 - 10-18-11