iP UMP 6400 Q UICK S TART G UIDE
Figure 4. iPump Web Interface Status Page
6. Shut down your iPump from the front panel. Navigate from the home screen to the Shutdown screen as follows:
Step Press Display / Field Details Screen Type j. k. l.
UNIT SETUP
UNIT STATUS DETAIL
NAVIGATION HELP
Menu
Menu
Menu m. UNIT SHUTDOWN Menu n. ENTER Are You Sure? !!!
No-ESC, Yes-ENTER
(Press ESC to cancel or ENTER to shut down.)
User Input -
Selectable o. ENTER
Press ESC to cancel or ENTER to shut down.
Status Display
At shutdown, the LCD screen becomes blank and the LED indicators go out. The iPump
is now shut down. The power switch on the rear panel may be left in the on position for quick restart from the front panel. (See note in Step
4
).
8000009-03 Rev. A 12 Professional Video iP
UMP
6400
Professional Media Server
Quick Start Guide
Professional Video
iP UMP 6400 Q UICK S TART G UIDE
Data, drawings, and other material contained herein are proprietary to Wegener Communications, Inc., and may not be reproduced or duplicated in any form without the prior written permission of
Wegener Communications, Inc.
The information contained herein is subject to change without notice.
Revisions may be issued to advise of such changes and/or additions.
WEGENER
UNITY·IP
,
COMPEL CONTROL
, and iPUMP
,
MEDIAPLAN
,
ENVOY
,
UNITY
,
are trademarks of
Wegener Communications,
Inc.
All other trademarks are the property of their respective owners.
2004 Wegener Communications, Inc. All rights reserved.
Portions copyright 1992-2001 FairCom Corporation. "FairCom" and
"c-tree plus" are trademarks of FairCom Corporation and are registered in the United States and other countries. All Rights
Reserved.
Correspondence regarding this publication,
800009-03 Release A
First Edition: April 2005 should be forwarded to:
Wegener Communications, Inc.
Technology Park/Johns Creek
11350 Technology Circle
Duluth, GA 30097-1502
Phone: 770-814-4000
Fax: 770-623-0698
The Wegener iPump 6400 is approved under FCC Part 15B Class A,
UL1950, CSA, and CE.
800009-03 Rev. A 2 Professional Video iP UMP 6400 Q UICK S TART G UIDE
Step Press Display / Field Details Screen Type a. UNIT SETUP b. ENTER RECORD AND PLAY c. DECODER SETUP d. AUDIO SETUP e. IP SETUP f. ENTER IP Address
____________
Menu
Menu
Menu
Menu
Menu
Data Display g. h. i.
Record the
IP Addres s of the iPump
unit displayed on the LCD screen.
Using a computer on the Ethernet LAN attached to the iPump
, open your web browser.
Type the
IP Address
noted from the
IP Address
screen in the browser's address box.
Note: For IP addresses that include subfields with leading zeros, you must omit those zeros when entering the address in your browser. For example, IP address 128.092.056.004
would be entered as 128.92.56.4.
Note: In some cases, it may be necessary to set specific values for the IP and Subnet addresses. Consult your network administrator.
j. k.
Press <
Enter
> (on the computer keyboard) and the iPump
's
Status page will be displayed (
Figure 4
).
Click the appropriate tab to select Files, Schedule, Status,
Help, or Setup.
Professional Video 11 800009-03 Rev. A
iP UMP 6400 Q UICK S TART G UIDE
8 To configure your iPump's decoder output , navigate from the
Home
screen to the
Decoder Setup
screen as follows:
Step Press Display / Field Details Screen Type a. ENTER RECORD AND PLAY b. w DECODER SETUP e. ENTER
Menu
Menu c. ENTER DECODER NUMBER
1
(Available decoders are 1 and 2. If your iPump has only one decoder, this Decoder Number screen will not appear. Instead, the Decoder
Setting Select screen described in step e will appear.
d. w
DECODER SETTING SELECT:
FOLLOW TUNE
(FOLLOW TUNE accepts the program selection from the current RF setup and sends you back to the Decoder Setup screen. PROGRAM allows you to select a particular program from the stream. OFF turns off the decoder)
User Input -
Selectable
User Input -
Selectable
If PROGRAM is selected, go on to step f. Otherwise your decoder setup is complete.
ENTER PROGRAM NUMBER:
001
(Number of program to select from stream.
Available program numbers are dependent on transport stream.)
User Input -
Selectable
Your decoder setup is now complete. The selected program will begin playing from the selected decoder.
For web browser control and status checking, first navigate from the home screen to the
IP Setup
screen as follows:
800009-03 Rev. A 10 Professional Video iP UMP 6400 Q UICK S TART G UIDE
Welcome to your iPump Media Server/Store and Forward
Receiver !
Your Wegener iPump is an advanced multimedia appliance that allows simple, efficient management of both live and recorded digital video, audio, and data content. With a single unit, you can receive, decode, and play out broadcast-quality transmissions while receiving and recording multiple programs or IP data files from a satellite or TCP/IP connection. Along with our
Compel MediaPlan ® software, you can insert content into real-time or recorded programs and can schedule playback of custom sequences of live and recorded content. This Quick Start Guide will help you quickly set up and start operating your iPump. For a full description of the iPump's abilities and detailed installation and operation instructions, please consult the iPump User's Reference Manual available on the worldwide web at wegener.com. For additional help, contact us by phone at (770) 814-4057, by fax at (678) 624-0294, or by email at [email protected].
1. Remove your iPump, ac power cord, and bagged accessories from the shipping carton. Call your shipping carrier immediately if any damage is discovered.
2. Place your iPump indoors on a well-supported, flat table or desktop or mount it in a standard equipment rack. If rackmounting your iPump, please consult the iPump User's
Reference Manual for detailed instructions and specific cautions.
f. g. h.
The L-band output from your antenna's LNB to the iPump's RF input port (a) [950 to 2150 MHz; female Type F connector with extender cable attached or BNC connector if your unit has the optional ASI input]
A suitable monitor to the iPump's audio port ( b). [A DB-15 HD cable assembly is included.]
A suitable video monitor to the iPump's video port ( c1) [c1 is a female BNC for SDI.] or ( c2) [c2 is a female BNC for composite video.]
Note: Repeat steps (b.) and (c.) for the second decoder if your iPump is equipped with two decoders.
Professional Video 3 800009-03 Rev. A
iP UMP 6400 Q UICK S TART G UIDE i.
Y our LAN line to the iPump's Ethernet port ( d female RJ-45 connector]
Figure 1. iPump Rear-Panel Connectors
The Alarm port ( e provide a contact closure during alarm conditions or on command from Compel. See the iPump User’s Manual for complete connector and signal details.
Figure 2. iPump Connections
Note: Do not connect devices to the mouse, keyboard and other connectors not described here. They are for factory use only.
8000009-03 Rev. A 4 Professional Video iP UMP 6400 Q UICK S TART G UIDE
LED Label Color and State Meaning
AUTH
WARNING*
ALARM*
GREEN constant Current transport stream is protected by conditional access (CA) and iPump is authorized and descrambling.
GREEN slow blink Current transport stream is protected by conditional access (CA) but iPump is unauthorized.
Off
AMBER constant
Tracked channel is not scrambled ("in the clear").
One or more warning conditions exist. Read warning information from front-panel LCD.
Off
RED constant
Off
No warning conditions exist.
One or more alarm conditions exist. Read alarm message from LCD.
No alarm condition exists
* Only one alarm or warning condition is displayed at a time on the LCD. When multiple alarm or warning conditions exist, those conditions are displayed in the order of importance. The most critical condition is displayed first and others may be viewed by pressing the right arrow button w .
7. Set up or adjust your iPump's RF settings at the front panel. (If your unit has the optional ASI input, this step is not necessary - go to step
7
). From the home screen, navigate to the
RF Setup
screen as follows:
Note: Use the arrow buttons to move left and right through the menu screens and the
ENTER
button to move down a level.
Use the
ESC
button to move upward through the menu screens. By pressing
ESC
repeatedly, you can always return to the iPump
home screen.
Step Press Display / Field Details a. ENTER b.
UNIT SETUP w
UNIT SETUP
Screen Type
Menu
Professional Video 9 800009-03 Rev. A
iP UMP 6400 Q UICK S TART G UIDE
The liquid crystal display (LCD) provides menu, data, and input screens to the user. Menu screens are entry points to further screens showing signal or unit status or to user-input screens that can be changed by the user. The "home" screen displays the iPump
Ratio
,
unit's
Serial Number
,
Eb/N0
, and alternately displays
FEC
Signal Frequency
, and
Transport Rate
. This screen may be reached at any time by repeatedly pressing the
ESC
button.
Six pushbuttons allow you to move through the various screens, select characters for input, and accept or reject changes. To move downward or upward through the menu screens, use the
ENTER and
ESC
buttons. To enter or change data in editable fields, press the
ENTER
button and use the up r and down s arrow buttons to increment the highlighted character or digit. Use the right w left v w and v arrow buttons to move to adjacent digits and press
ENTER again to accept your input. Pressing
ESC
before accepting your input will cancel any changes.
Eight light-emitting diodes (LEDs) illuminate to show unit status at a glance.
Table 1
gives the meaning of each LED indicator.
Table 1. LED Indicator Descriptions
LED Label Color and State Meaning
CARRIER
RECORD
DOWNLOAD
LAN
COMPEL
GREEN constant Receiver is tracking carrier.
GREEN slow blink Receiver is not tracking carrier.
GREEN constant iPump
is recording a program.
Off
GREEN constant
Off
GREEN constant iPump iPump
is not recording.
is downloading a file via Compel.
iPump
is not downloading.
Light network activity over the iPump's LAN interface.
GREEN slow blink Heavy network activity over the iPump's LAN interface.
Off iPump
observed no packet transfers during the last 20 secs.
GREEN constant iPump
has received a Compel command within the last two minutes.
GREEN fast blink iPump has been addressed by Compel within the last five seconds.
GREEN slow blink iPump is in tracking mode and Compel is required but no Compel command received within the last two minutes.
800009-03 Rev. A 8 Professional Video iP UMP 6400 Q UICK S TART G UIDE
4. Next, start your iPump as follows: a.
Connect the ac power cord to the iPump
's IEC receptacle ( ff ,
Figure 1
) and to a 100-to-120-Vac or 200-to-240-
Vac source.
b.
Set the power switch to the On position ( I ) and press and hold the
ENTER
button on the front panel for two seconds. The iPump
will power up and begin the boot process.
Outputs are muted during the short initialization time. All eight
LED indicators flash on and off as the unit begins initialization.
Until you configure your iPump
's RF settings (see Step 6 ), a loss-of-carrier alarm may be displayed (red
ALARM
LED indicator is lit and LCD screen indicates the alarm state). RF settings are not necessary for units with the optional ASI input.
Note: To easily restart the iPump
any time after a normal shutdown
(see Step 9 ), simply press the
ENTER
button on the iPump
’s front panel (refer to the
User's Manua l for details). If the receiver is tracking a carrier signal, the green
CARRIER
LED will light.
5. Get to know the iPump's front panel
Figure 3. iPump Front-Panel Controls and Indicators
Liquid Crystal Display (LCD)
LED Indicators
Pushbuttons
Professional Video 5 800009-03 Rev. A
iP UMP 6400 Q UICK S TART G UIDE
Step Press Display / Field Details Screen Type a. ENTER b. c. ENTER d. e.
UNIT SETUP
UNIT SETUP
RECORD AND PLAY
DECODER SETUP
AUDIO SETUP
Menu
Menu
Menu
Menu
Menu
Menu f. IP SETUP g. RF SETUP Menu
Note: To enter data in editable fields, press
ENTER
and use the up r and down s arrow buttons to increment the highlighted character or digit. Use the right w input or
ESC to cancel changes.
and left v arrow buttons to move to adjacent digits. Press
ENTER
again to accept your
From RF Setup, adjust RF settings as follows: iP UMP 6400 Q UICK S TART G UIDE
Step Press Display / Field Details Screen Type k. CURRENT CHANNEL l. ENTER DOWNLINK FREQUENCY:
XXXXX.XX MHz
(Enter downlink frequency from the LNB local oscillator in megahertz.) m. TRANSP. DATA RATE:
XXX.XX Mbps
(Enter transport stream data rate in megabits per second.) n. o. p.
RF-MOD/FEC RATIO:
QPSK 3/4
(RF Modulation is QPSK. Available Forward
E rror Correction Ratios are 1/2, 2/3, 3/4, 5/6, and 7/8.)
PROGRAM NUMBER:
00001
(Number of program to select from stream).
TAG SITE: q. SAVE ALL CHANGES?
YES<ENT> NO<ESC>
(Press ENTER to save or ESC to cancel all
RF Setup changes.)
Menu
User Input -
Editable
User Input -
Editable
User Input -
Selectable
User Input -
Editable
<Unused>
User Input -
Selectable
If you are satisfied with all data entered, press
ENTER
to save your changes. Pressing either
ENTER or ESC
(which cancels all changes) completes your RF setup and returns you to the
Current Channel screen. If all settings are correct and the red
ALARM LED remains lit, there may be a problem with the antenna, its position, or cable connections. Consult the iPump
User’s Manual
for more troubleshooting help.
6. To configure your iPump's decoder output , navigate from the
Home
screen to the
Decoder Setup
screen as follows:
Step Press h. i. j.
Display / Field Details Screen Type
ENTER RF STATUS:
TRACKING: Eb/No = XX.X
(RF status is shown. If tracking, then E b also displayed.)
/N
0
is
Data Display
CURRENT CHANNEL Menu
ENTER RF STATUS:
TRACKING: Eb/No = XX.X
(RF status is shown. If tracking, then E b also displayed.)
/N
0
is
Data Display
8000009-03 Rev. A 6 Professional Video Professional Video 7 800009-03 Rev. A
