Acroprint TQ600 User manual

TQ600

User Manual

Proximity Badge

Terminal

Fingerprint

Terminal

FCC Warning:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme a la norme NMB-003 Du

Canada.

Lithium Battery Caution:

The circuit board on this terminal is populated with a lithium battery to protect data or programs stored in the Random Access Memory (RAM). Do not, under any circumstances, attempt to replace the lithium battery in the terminal. Failure to comply may invalidate your warranty. Battery replacement should be done by qualified personnel wearing the proper eye protection.

CAUTION: Danger of explosion if the battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instruction.

This product utilizes a battery that contains Perchlorate Material.

Perchlorate Material – special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate

- I -

Declaration Of Conformity According To EMC Directive 89/336/EEC

We declare under our sole responsibility that the U600 Finger Print reader and/or U600P Proximity reader and/or data recording equipment to which this declaration relates are in conformity with the following standards:

EN61000-6-1, EN55022-2006, EN55024-1998+A1:2001+A2:2003. I, the undersigned, hereby declare that the equipment specified above conforms to the above directive and standards.

September 15, 2008 W. Glenn Robbins

All Rights Reserved. © COPYRIGHT 2008

Acroprint Time Recorder Company

- II -

Contents

Getting Started ......................................................... 1

Terminal Configurations.....................................................................2

Operator Panel LEDs ..........................................................................3

Menu Tree.................................................................. 4

Basic Concepts ......................................................... 8

User Enrollment: Fingerprints.........................................................8

User Identification / Verification ........................................................9

Threshold.............................................................................................9

User ID (PIN number)........................................................................ 11

Privilege Levels................................................................................. 11

Start-up ..............................................................................................12

Enrolling – Fingerprint Terminals ........................... 13

Fingerprint Enrollment Tips .............................................................13

Enrolling Users – Fingerprint Terminals .........................................16

Fingerprint Enrollment ................................................................17

Testing a Fingerprint Enrollment .................................................19

Enrolling Auxillary Fingerprints ...................................................19

Password Enrollment..................................................................20

Fingerprint & Password ..............................................................22

User Verification Types.....................................................................24

Fingerprint Verification ................................................................24

- III -

Password Verification ................................................................. 27

Enrolling – Proximity Terminals ..............................29

Proximity Card Enrollment.......................................................... 29

Password Enrollment ................................................................. 30

Proxmity Card & Password Enrollment ...................................... 32

Prvilege Levels ........................................................34

Enroll w/ Privilege Level................................................................... 35

Delete User Data .....................................................37

Options.....................................................................38

System Options ................................................................................ 39

Set Date and Time...................................................................... 39

Changing the Time Format ......................................................... 40

Changing the Language ............................................................. 40

Changing the Date Format ......................................................... 41

Advanced Options ...................................................................... 42

Power Manager ................................................................................. 44

Communication Options .................................................................. 46

Log Options....................................................................................... 47

Auto Test ........................................................................................... 48

System Information .................................................49

View Time and Attendance Records ......................51

- IV -

Review All Attendance Records ......................................................51

Review Individual Attendance Records ..........................................52

Browsing Attendance Records ........................................................53

Cleaning the TQ600................................................. 55

Troubleshooting ...................................................... 56

Appendix.................................................................. 58

USB Flash Drive Management .........................................................58

Bell Schedule ....................................................................................58

Reserve Battery (Mini-UPS)..............................................................59

Daylight Saving Time (DST) .............................................................60

Work Codes .......................................................................................61

- V -

1

Getting Started

Important!

Do not attempt to service the TQ600 yourself. Opening the terminal will void the warranty. Always follow the instructions in the user guide.

• Do not place the terminal in direct sunlight. Bright light may significantly affect fingerprint reads or cause fingerprint verification to fail. The terminal is designed for indoor use in a temperature range of 32-104º F (0-40º C). Keep the terminal away from heat sources such as radiators.

• The terminal warranty does not cover defects or damages arising from improper installation, improper storage, abuse, ordinary wear or unauthorized service.

- 1 -

Terminal Configurations

The TQ600 is available with either a fingerprint sensor or a proximity badge sensor. The fingerprint sensor provides the most secure user verification as it uniquely identifies each user. The proximity (“Prox”) badge is a faster method of verifying a user since you only need place your badge near the front of the terminal for verification but security could be circumvented since a user other than the owner of the badge can use the badge.

This manual provides information for both terminal configurations.

Sections specifically about fingerprint verification or proximity badge verification will pertain only to the corresponding terminal.

- 2 -

Operator Panel LEDs

1) Normal Operation.

Green light blinks each second .

2) Error Condition (Fingerprint or Badge not Enrolled)

Red light shines for 2 seconds

3) Transaction (Fingerprint or Badge Read) successful

Green light shines for 2 seconds

Note: Contact Acroprint support if you receive any LED sequence other than those listed above.

- 3 -

Menu Tree

2

- 4 -

- 5 -

- 6 -

- 7 -

3

Basic Concepts

This section contains definitions and descriptions of fingerprint identification concepts: z User Enrollment: Fingerprints z User Identification/Verification z Threshold z User ID (PIN Number) z Privilege Levels z Start-up

The two most important functions of fingerprint identification are user enrollment and user verification.

User Enrollment: Fingerprints

Enrollment is the process of capturing a user’s fingerprint and storing it as a “template” in the TQ600 along with a unique five (5) digit user ID. The user’s fingerprint template is created by taking three sample fingerprints on the TQ600.

Each user should enroll at least two different fingers so that if an enrolled finger is injured an alternate finger can be used. The

TQ600 allows users to enroll 1-10 fingerprints.

- 8 -

User Identification / Verification

User identification is the process of comparing a user’s fingerprint against a fingerprint template stored in the terminal. When a user’s fingerprint matches a fingerprint template stored in the

TQ600 the terminal will show a successful match, thus verifying the user’s identity.

Threshold

The threshold is a predefined number (set by the terminal system administrator) which establishes the degree of correlation necessary for a fingerprint comparison to be deemed a match. It can be thought of as the minimum accuracy required to confirm a fingerprint match. Some biometric systems call this the

“sensitivity” level. If the score resulting from a fingerprint read compared to a fingerprint template stored in the terminal exceeds the threshold the templates are approved as a “match” (though the templates themselves are not identical).

The threshold establishes a balance between False Acceptance Rate

(FAR) and False Rejection Rate (FRR). FAR means the probability that a biometric system will incorrectly identify an individual or will fail to reject an impostor. FRR means the probability that a biometric system will fail to identify an enrolled individual.

- 9 -

The threshold value is a global setting, i.e., it is set for all users.

If a user has a problem with fingerprint verification due to worn fingerprints or dry skin you may need to have the user enter their

User ID in order to match their fingerprint to their stored template.

This is referred to as 1:1 (one to one) verification since they are specifically comparing their fingerprint to their stored template.

Raising the threshold increases security or the probability that a successful fingerprint read accurately corresponds to the correct stored fingerprint template. Lowering the threshold increases the possibility of a false acceptance. The correct balance is vital for maximum security as well as usability.

Notice: FAR and FRR are interrelated: For example, raising the threshold reduces FAR but increases FRR, while lowering the threshold increases FAR but reduces FRR. The threshold value can be set independently for “one to many” (1:N) matching and

“one to one” (1:1) matching. The default threshold for (1:N) is 35 and the default threshold for (1:1) matching is 15.

FRR

High

Middle

Low

Table 1—1 Suggested Threshold Settings

FAR

Low

Middle

High

One-to-Many

(1:N)

45

35

25

One-to-One

(1:1)

25

15

10

- 10 -

User ID (PIN number)

Before beginning fingerprint enrollment, a user is assigned a User

ID number (sometimes referred to as a PIN number). This User ID number is used to recall fingerprint templates or passwords each time verification is requested.

Privilege Levels

Privilege levels are the levels at which users are authorized to access terminal functions. These levels define the authority of a user to access specified administrative functions including the ability to view, edit, add, or renew specified information categories.

Privilege levels are built-in terminal functions that can be set as required. The TQ600 has four user privilege levels:

User, Enroller, Admin (administrator) and Supervisor. z Users are people whose identity must be verified to record time such as punching in/out or the time spent working on a job or working in specific departments. z Enrollers can enroll supervisors, administrators, enrollers and users. Enrollers can delete users. Enrollers can access “User Manage” and “System Information” menus. z Administrators (Admin) can enroll supervisors, administrators, enroller and users. Administrators can delete enrollers and users. Administrators can access all operations, except “Advanced Options”.

- 11 -

z Supervisor is the highest authorization level.

Supervisors can enroll supervisors, administrators, enrollers and users. Supervisors can delete administrators, enrollers and users. Supervisors can access all functions and change all setups.

Note: If no user has administrative privileges (enroller, administrator or supervisor) in the terminal, ALL users will be enrolled with

“Supervisor” privileges.

To change a user that is currently enrolled as an administrator or enroller, delete the user and then re-enroll the user with the new privilege level.

Start-up

Press the power button () to turn the TQ600 on. The Start-up” window will appear:

Welcome

10:12

06-18-08

Press and hold the power button () for 2 seconds to turn off the

TQ600.

- 12 -

Enrolling – Fingerprint

Terminals

This chapter describes how to enroll and verify users on the TQ600.

The following topics are included: z Fingerprint Enrollment Tips z Enrolling User z Testing an Enrollment z Enrolling an Auxiliary Fingerprint of User z Verifying Your Identity

4

Fingerprint Enrollment Tips

It is recommended that you use your index or middle finger for enrollment. If the fingerprints on your preferred hand are worn or damaged try using your other hand.

The TQ600 will require three (3) sample fingerprints to enroll a user.

Place your finger in the middle of the sensor. To ensure better fingerprint reads take each fingerprint sample with slightly different positioning; one centered, one rolled slightly to the left and the last rolled slightly to the right. The different angles will help account for different finger positioning during actual use.

- 13 -

CORRECT finger positioning:

Place finger flat on the sensor surface

Place finger in the center of the sensor surface

INCORRECT finger positioning:

- 14 -

Tips for improving the quality of finger print reads:

Correction

Dirty or Dry Clean finger with moisturizing soap or wipe with a

Finger pre-moisturized tissue (alcohol-free wipes preferably, enriched to hydrate the skin) pressure

How to select finger?

How to position the finger?

Fingerprint pattern change

Others sensor surface.

Use the index or middle finger to enroll; try the left hand fingers if the right hand fingerprints are worn, damaged or missing.

If the user’s fingers are small, select the thumb.

Place finger in the middle of the sensor; keep finger flat on the sensor and apply pressure while covering as much of the sensor window as possible; DO

NOT touch the sensor in an angled or tilted position, DO NOT slide finger.

For a user with a worn or injured finger, the identification can be affected.

Use an alternate finger or select password verification.

A few people’s fingerprint quality is too poor to verify. Use the User ID & Fingerprint verification, and lower the 1:1 Threshold. Otherwise use

Password verification.

- 15 -

Enrolling Users – Fingerprint Terminals

After configuring the TQ600 you are ready to enroll users. If there are no users on the system all users will have a privilege level of supervisor, if an administrator (Admin) is enrolled on the system they will be the only one allowed to enroll a new user.

The TQ600 provides three ways to enroll, Fingerprint Enrollment,

Password Enrollment, or Fingerprint with Password Enrollment.

Fingerprint Enrollment is preferable for personnel with good fingerprint definition; Fingerprint with Password is preferable for users that have difficulty verifying their finger print. Password

Enrollment is necessary for users whose fingerprints are too worn or damaged for the terminal to read their fingerprint.

To start the enrollment process, identify yourself. Press [MENU], enter your ID number or fingerprint, and verify your identity.

Note: If this is the first enrollment in a new or empty system, you will not be prompted for verification.

- 16 -

Fingerprint Enrollment

Notes on Buttons:

F1 = ESC, use to back up in the menu or quit

F2 = ▲, use to scroll up in the menu

F3 = ▼, use to scroll down in the menu

F4= OK, use to select a menu item

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. Three enrollment methods are displayed, select “Enroll FP”, press [OK]. The following screen is displayed:

Enroll FP

New Enroll?

ESC OK

2) Press [OK]. The following screen is displayed:

New Enroll

UserID 00001

ESC OK

- 17 -

Note: The User ID (PIN number) is a 5 digit number. If you input less than 5 digits the terminal pads the User ID with 0’s in front of the User ID, i.e., if you enter 11 the User ID 00011 is displayed on the terminal.

3) Input the User ID (range is 1 to 65534), press [OK].

The following appears:

New Enroll

00011-0

Place Finger…

ESC/Exit

Note: 00011-0

The dash number (-0) indicates the first fingerprint.

4) You will be prompted to take (3) samples of your fingerprint.

If the test is successful three times in a row, the following appears:

New Enroll

00011-0

ESC OK (Save)

5) Press [OK], the previous message continues to be displayed while the template is created. If your identity cannot be verified, you are prompted to try again and you must restart the verification procedure (Refer to Step 2).

- 18 -

Testing a Fingerprint Enrollment

Ask the user to place their finger on the fingerprint sensor. If the test was successful the enrollment is complete. If the terminal cannot read the fingerprint or if several attempts are required for the terminal to verify the fingerprint, the user should try 1:1 verification (refer to page 25).

Enrolling Auxiliary Fingerprints

It is a good practice to enroll at least two fingers for each user.

Press [MENU], select “User Manage”, press [OK], select “Enroll

User”, press [OK], select “Enroll FP”, press [OK], the following appears:

Enroll FP

New Enroll?

ESC OK

Press [ESC] to cancel the new enrollment, enter the User ID (PIN number) of the user you wish to enroll an additional fingerprint for:

Backup Enroll

User ID 00001

ESC OK

- 19 -

Password Enrollment

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. Three enrollment methods are displayed, select “Enroll Pwd”, press [OK]. The following screen is displayed:

Enroll Pwd

New Enroll?

ESC OK

2) Press [OK] to enroll new user, the following screen is displayed:

New Enroll

User ID 00006

ESC OK

3) Note: The next available User ID is displayed. Press [OK] to choose this ID or enter a User ID (range is 1 to 65534) & press

[OK]. The following screen is displayed:

New Enroll

Input Pwd_

ESC OK

- 20 -

4) Input the password and affirm:

New Enroll

Input Pwd *****

Pwd Affirm *****

5) Press [OK], the following screen is displayed:

New Enroll

00006-P

ESC OK (Save)

Note: 00006-P

“-P” means password enrollment

6) Press [OK]. Press [ESC] to exit user enrollment or press [OK] to continue Password enrollment.

- 21 -

Fingerprint & Password

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. Three enrollment methods will be displayed, select “FP & Pwd”, press [OK]. The following screen is displayed:

FP & Pwd

New Enroll?

ESC OK

2) Press [OK], the following appears:

New Enroll

User ID 00008

ESC OK

3) Press [OK], the following appears:

New Enroll

00008-0

Place Finger…

ESC/Exit

- 22 -

4) If the test is successful three times in a row, the following appears:

New Enroll

00008-0

Input Pwd *****

ESC OK

5) Input your password, the following appears:

New Enroll

00008-0

Input Pwd *****

Pwd Affirm *****

6) Input the password again, press [OK], the following appears:

New Enroll

00008-0P

ESC OK (Save)

Note: 0000-0P; “-0P” indicates first fingerprint and password.

7) Press [OK], the previous message continues to be displayed while the template is created.

- 23 -

User Verification Types

Fingerprint Verification

There are (3) fingerprint verification (“authentication”) types:

1:1 Verification (“One to One” Verification)

In this mode, a user enters their 5-digit User ID and takes a fingerprint reading. The TQ600 compares their fingerprint to the fingerprint template of the User ID that was entered, thus a 1:1 comparison. The 1:1 verification method is the fastest verification method since it only has to compare the user’s fingerprint to one template stored in the terminal.

1) In the initial interface, enter your ID number and the following appears:

1:1 FP Match

User ID 00011

ESC OK

Note: The User ID is 5 digits. If you enter a number with less than 5 digits the TQ600 adds 0’s in order to create a 5 digit

User ID, i.e., if you enter “11” the TQ600 will Enroll “00011”.

- 24 -

2) Press [OK] and the following appears:

FP Verify

User ID 00011

Place Finger…

3) It continues for about 0.5 seconds.

If the test is successful, the following appears:

Verify

User ID 00011

Verified.

4) If your identity cannot be verified, you are prompted to try again, the following appears:

1:1 FP Match

Please Try Agn.

It continues for about 0.5 seconds then returns to the start-up window.

- 25 -

1:N Verification (“One to Many” Verification)

In this mode, a user simply takes a fingerprint reading. The TQ600 compares their fingerprint to all of the fingerprint templates stored in the terminal. 1:N verification takes more time than 1:1 verification. The verification time is dependent on the number of fingerprint templates stored in the terminal.

1) Place finger on the sensor surface, the following appears:

FP Verify

Remove Finger

2) It continues for about 0.5 seconds. If the test is successful, the following appears:

Verify

User ID 00001

Verified.

3) If your identity cannot be verified, you are prompted to try again, the following appears:

FP Verify

Please Try Agn.

It continues for about 0.5 seconds, return to the start-up window.

- 26 -

Password Verification

A password 1 to 5 digits long is used to validate authentication.

Password verification can be used in special cases, i.e., when all of a user’s fingerprints are damaged. This method of verification does not provide the security of biometric identification and should only be used when absolutely necessary. Note: when a user with an enrolled password attempts (1:1) verification the TQ600 will ask for the User’s password and the user will not have the option of taking a fingerprint reading.

1) To verify a password, enter your ID number, the following appears:

PWD Affirm

User ID 00008

ESC OK

2) Press [OK], the following appears:

Pwd Affirm

User ID 00008

Input Pwd *****

3) Input correct password, press [OK], the following appears:

Verify

User ID 00008

Verified.

- 27 -

4) If the password cannot be verified, the following appears:

Pwd Affirm

Error Pwd.

- 28 -

Enrolling – Proximity

Terminals

This chapter describes how to enroll users on the TQ600P.

5

Proximity Card Enrollment

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. The following screen is displayed:

Enroll User

►Reg RFID

Enroll Pwd

Reg Card&Pwd

2) Select “Reg RFID”, press [OK]. The following screen is displayed:

New Enroll

User ID 00001

ESC OK

3) Enter a User ID (PIN number) and scan a proximity badge that hasn’t been assigned to any users. The following screen is displayed:

New Enroll

CARD: 0001234567

User ID 00010

ESC OK

- 29 -

4) Press [OK] to complete the enrollment. The following screen

appears:

New Enroll

00010-C

ESC OK (Save)

5) Press [OK] to save enrollment. Press [ESC] to cancel the new enrollment.

Password Enrollment

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. Three enrollment methods are displayed, choose “Enroll Pwd”, press [OK]. The following screen is displayed:

New Enroll

User ID 00006

ESC OK

- 30 -

2) The next available User ID is displayed. Press [OK] to choose this ID or enter a User ID (range is 1 to 65534) & press

[OK]. The following screen is displayed:

New Enroll

Input Pwd_

ESC OK

3) Input the password and affirm:

New Enroll

Input Pwd *****

Pwd Affirm *****

4) Press [OK], the following screen is displayed:

New Enroll

00006-P

ESC OK (Save)

Note: 00006-P

“-P” means password enrollment.

5) Press [OK]. Press [ESC] to exit user enrollment or press [OK] to continue Password enrollment.

- 31 -

Proximity Card & Password Enrollment

1) Press [MENU], select “User Manage”, press [OK], select

“Enroll User”, press [OK]. Three enrollment methods are displayed, select “Reg Card&Pwd”, press [OK]. The following screen is displayed:

New Enroll

User ID 00008

ESC OK

2) Enter a User ID (PIN number) and scan a proximity badge that hasn’t been assigned to any users. The following screen is displayed:

New Enroll

CARD: 0015416415

User ID 00008

ESC OK

3) Press [OK], the following appears:

New Enroll

CARD: 0015416415

Input Pwd _

ESC OK

- 32 -

4) Input your password, press [OK], the following appears:

New Enroll

CARD: 0015416415

Input Pwd *****

Pwd Affirm _

5) Affirm your password, press [OK], the following appears:

New Enroll

00008-P

ESC OK (Save)

Note: 00006-P

“-P” means password enrollment.

6) Press [OK] to save. Press [ESC] to cancel the enrollment.

- 33 -

6

Prvilege Levels

The TQ600 has four user privilege levels: User, Enroller, Admin

(administrator) and Supervisor. z Users are people whose identity must be verified to record time such as punching in/out or the time spent working on a job or working in specific departments. z Enrollers can enroll supervisors, administrators, enrollers and users. Enrollers can delete users. Enrollers can access “User Manage” and “System Information” menus. z Administrators (Admin) can enroll supervisors, administrators, enroller and users. Administrators can delete enrollers and users. Administrators can access all operations, except “Advanced Options”. z Supervisor is the highest authorization level.

Supervisors can enroll supervisors, administrators, enrollers and users. Supervisors can delete administrators, enrollers and users. Supervisors can access all functions and change all setups.

Note: If no user has administrative privileges (enroller, administrator or supervisor) in the terminal, ALL users will be enrolled with

“Supervisor” privileges.

To change a user that is currently enrolled as an administrator or enroller, delete the user and then re-enroll the user with the new privilege level.

- 34 -

Enroll w/ Privilege Level

Important! Until you enroll a user with at least Administrator privileges, all users will automatically be entered with Supervisor privileges even if they were entered as users. In order to prevent unauthorized personnel from making changes to the TQ600 you should enroll a user with Administrator password security.

1) Press [MENU]. Select “User Manage”, press [OK].

Menu ▼

►User Manage

Options

PenDrive Mng

2) The User Manage screen appears:

User Manage ▼

User Enroll

►Enroll Admin

Delete

- 35 -

3) Select “Enroll Admin”, press [OK], the following appears:

Enroll Admin

►Enroll FP

Enroll Pwd

FP & Pwd

4) You can enroll an employee with (3) possible levels of terminal privileges: (1) “Supervisor”, (2) “Admin” or (3) “Enroller”.

- 36 -

7

Delete User Data

1) Press [MENU], the following appears:

Menu ▼

►User Manage

Options

PenDrive Mng

2) Select “User Manage”, press [OK], the following appears:

User Manage ▼

Enroll User

Enroll Admin

►Delete

3) Select “Delete”, press [OK], input the User ID, press [OK] to confirm, follow the prompts to delete user.

Delete

User ID 00008

ESC OK

Note: You cannot delete a user with multiple enrolled fingerprints without deleting each fingerprint first. If the user has a password you will also need to delete it before you can remove the user from the terminal.

- 37 -

8

Options

Press [MENU] and verify your identity. The following appears:

Menu

User Manage

►Options

PenDrive Mng

Select “Options”, press [OK], the following appears:

Options

►System Opt

Power Mng

Comm Opt

----------------------------

Log Opt

Auto Test

The following topics are reviewed in this section: System Options,

Power Management, Communication Options, Log Options and

Auto Test.

- 38 -

System Options

Select “System Opt”, press [OK], the following appears:

System Opt ▼

►Date Time

Time Fmt 12H

Language ENG

----------------------------

Fmt MM/DD/YY

Adv Option

The System Options are: Date & Time, Time Format, Language,

Display Format and Advanced Options.

Set Date & Time

Select “Date Time”, press [OK] the following appears:

YYYY-MM-DD 24H

2008-01-02

08:24:35

ESC OK

To change the date & time, input the correct date, press [▲/▼], enter the time and press [OK].

Note: The time and date will update automatically when the terminal is connected to the network.

- 39 -

Changing the Time Format

Select “Time Fmt”, press [OK], press [▲/▼] to change between

12 Hour and 24 Hour Format.

Changing the Language

Select “Language”, press [OK], press [▲/▼] to select the language (the default language is English), press [OK].

System Opt ▼

Date Time

Time Fmt 12H

►Language ENG

Press [ESC] to exit system options. The system will prompt you to save the setup, press [OK]. Restart the terminal for the language change to take effect.

System Opt ▼

Date Time

Time Fmt 12H

►Language ENG

Opc. Sistema ▼

Fecha y Hora

Time Fmt 12H

►Idioma ESP

English Spanish

- 40 -

Changing the Date Format

Select “Fmt YY-MM-DD”, press [OK], press [▲/▼] to select the date and time format, press [OK].

System Opt ▼

Time Fmt 12H

Language ENG

►Fmt YY-MM-DD

There are ten formats: YY-MM-DD, YY/MM/DD, YY.MM.DD,

MM-DD-YY, MM/DD/YY, MM.DD.YY, DD-MM-YY,

DD/MM/YY, DD.MM.YY, YYYYMMDD.

E.g.: YY/MM/DD format (left) change to YY-MM-DD format (right)

Welcome

17:37

08/06/18

WED

Welcome

17:37

08-06-18

WED

- 41 -

Advanced Options

Select “Adv Option”, press [OK], the following appears:

Adv Option ▼

►Reset Opts.

Del AttLogs

Clear All Data

----------------------------

Clr Admin Pri

Show Score N

Match Thr 35

Mst Input ID N

1:1 Thr 15

Voice Y

Upd Firmware

Work Code NO

Adj VOL(%) 67

Press [▲/▼] to scroll up or down to select the option.

„ Reset Opts.: Restore all setup values to factory defaults.

„ Delete AttLogs: Delete all transaction logs.

„ Clear All Data: Delete all users and logs. (Note: You will lose all information stored on the terminal.)

„ Clr Admin Pri: Change all privilege levels to User.

„ Show Score: Show the degree to which a fingerprint reading matches the stored template. 0 is the lowest score (no match) and 50 is the highest score (perfect match).

- 42 -

„ Match Thr: Set the fingerprint match threshold level. The threshold value can be set 0 – 75 (default is 35). See Table

1-1.

„ Mst Input ID: Turns 1:1 (one to one) fingerprint verification on or off.

„ 1:1 Thr: The minimum fingerprint read correlation needed to achieve a positive match for 1:1 verification.

„ Voice: Set the voice prompts on or off.

„ Upd Firmware: The user cannot update the firmware unless this feature has been enabled by an authorized

dealer.

„ Work Code: Not available at this time.

„ Adj VOL(%): Adjust the volume level (0-99); “0” turns off the speaker.

- 43 -

Power Manager

Select “Power Mng”, press [OK], the following appears:

Power Mng ▼

►Shutdown N

PowerOn N

Sleep N

----------------------------

Idle SLP

Idle Min 0

Bell Delay 10

Scheduled Bell

Lock Power N

„ Shutdown: Set a time the terminal will automatically turn off.

The terminal can be turned on again with the power button.

Select Shutdown, press [OK], the following appears:

Shutdown

Set Sch. Fun?

ESC OK

After setting the shutdown time, press [ESC] and then [OK] to save the settings.

„ PowerOn: Set a time the terminal will automatically turn on.

- 44 -

„ Sleep: Set a time the terminal will go into sleep mode.

Pressing any button will awaken the terminal.

„ Idle: Select “SLP” or “OFF” for the Idle mode. “SLP” –

Sleep mode allows the terminal to be awakened by pressing any key. “OFF” - Turns the unit off and the power button must be pressed to turn the unit on.

„ Idle Min: Set how many minutes of no use before the terminal goes into the selected “Idle” mode. Setting “Idle

Min” to “0” turns off this feature.

„ Bell Delay: Set the length of time the bell sounds. A setting of 5 sets the bell to ring for 10 seconds. A setting of 10 sets the bell to ring for 20 seconds.

„ Scheduled Bell: There are 20 bell schedules. Enter the times you would like the bell to sound. The bell will sound at the scheduled times for the duration set in the “Bell Delay”.

„ Lock Power: If set to “Y” the terminal cannot be turned off using the power button. To turn the unit off with the power button locked, enter the “Power Mng” menu and scroll down to “Power Off”.

- 45 -

Communication Options

Select “Comm Opt”, press [OK], the following appears:

Comm. Opt ▼

►Baud Rate 115200

Dev Num 1

IP Addr

----------------------------

Net Speed AUTO

NetMask

Gateway

Ethernet Y

RS232 N

RS485 N

USB Y

COMM Key 0

The TQ600 fully supports Ethernet, RS232 & USB communications.

„ Baud Rate: The baud rate may be set to 9600, 19200 38400,

57600 & 115200.

„ Dev Num: The terminal’s unique Device Number, the range is

1 to 255.

„ IP Addr: Defaults to IP address 192.168.1.201

„ Net Speed: The default Net Speed is “AUTO”, the other options are 10M-F, 10M-H, 100M-F and 100M-H.

- 46 -

„ NetMask: The default Net Mask is 255.255.255.0

„ Gateway: The default gateway is 0.0.0.0

„ Ethernet: Turn Ethernet connectivity on or off.

„ RS232: Turn RS232 connectivity on or off.

„ RS485: Not Supported

„ USB: Turn USB connectivity on or off. Note: This is a serial connection established via USB cable.

„ COMM Key: Not utilized

Note: After setting, restart the terminal for the new configurations to take effect.

Log Options

Select “Log Opt”, press [OK], the following message appears:

Log Opt

►Alm SuperLog 99

Alm AttLog 99

ReCheck Min 0

„ Alm SuperLog: An alarm will sound to alert the supervisor that the logs are full. The set number is the remaining log capacity before the logs are full, set from 0-99.

- 47 -

„ Alm AttLog: An alarm will sound when the logs are full.

The set number is the remaining log capacity before the logs are full, set from 0-99.

„ ReCheck Min: Set the number of minutes before another punch is accepted by the terminal. If a punch occurs within the ReCheck Minutes, the punch will not be logged. This reduces duplicate (accidental) punches.

Auto Test

Select “Auto Test”, press [OK], the following appears:

Auto Test ▼

►Run All Test

FLASH Test

LCD Test

----------------------------

Voice Test

FP Test

Key Test

RTC Test

These options allow the testing of each portion of the terminal in order to pinpoint failures.

WARNING: Do not disconnect or interrupt power while performing any of the tests (loss of power during testing may damage the hardware.

- 48 -

9

System Information

System Information allows review of the terminal information. Press

[Menu], select “Sys Info”, press [OK], the following appears:

Sys Info ▼

►User Cnt 206

FP Cnt 173

Att Log 8046

----------------------------

Admin Cnt 2

Pwd User 30

S Logs 263

Free Space Info

Dev Info

„ User Cnt: The number of enrolled users.

„ FP Cnt: The number of enrolled fingerprints.

„ Att log: The number of punches stored in the system.

„ Admin Cnt: The number of users enrolled with Supervisor,

Admin and Enroller privledges.

„ Pwd User: The number of users using a password for authentication.

„ S Logs: The number of supervisor logs.

„ Free Space Info: The remaining log capacity before reaching the set alarm point.

- 49 -

„ Dev Info: Terminal information (see below)

‹ Users (100): 100: Proximity Terminal: Maximum number of users (100 X 100 = 10,000).

‹ FPCnt (100): 15: Biometric Terminal: Maximum number of fingerprints (15 X 100 = 1,500).

‹ AttLog (10k): 5: Maximum number of transaction (5 X

10,000 = 50,000).

‹ S Logs: 4096: Maximum number of supervisor logs

(tracks menu access).

‹ Manu Time: Terminal’s date/time of manufacture.

‹ Serial Num: Terminal serial number.

‹ Vendor: Dealer name

‹ Device Name: U600 (Biometric), U600-P (Proximity).

‹ Alg Version: The version of the fingerprint identification algorithm.

‹ Firmware Ver: The version of the terminal firmware.

- 50 -

10

View Time and Attendance

Records

Time & attendance records stored inside the terminal can be reviewed.

Review All Attendance Records

1) Press [MENU], select “User Manage”, press [OK], select

“Browse AttLogs”, press [OK] and the following appears:

Browse AttLogs

User ID 00000

ESC OK

2) Press [OK] with User ID as “00000” and all terminal attendance records will be displayed. Scroll through the records using [▲▼].

1/380

00001 05-27 18:46:21I

00012 05-27 18:32:09I

00217 05-27 18:30:52I

00031 05-27 18:29:01I

00016 05-27 18:27:55I

00029 05-27 18:22:08I

3) Press [ESC] to return to normal operation

- 51 -

Review Individual Attendance Records

1) Press [MENU], select “User Manage”, press [OK], select

“Browse AttLogs”, press [OK] and the following appears:

Browse AttLogs

User ID 00000

ESC OK

2) Enter User ID (“00014 for example), press [OK] and the individual attendance records will be displayed. Scroll through the records using [▲▼].

00014 2006-5 1/23

27 08:30 12:10 13:20

18:08

26 08:46 12:15 13:25

18:23 18:55 22:20

25 08:53 12:07 13:19

18:23

3) Press [ESC] to return to normal operation

- 52 -

Browsing Attendance Records

The table below details additional commands for browsing attendance records:

Key Description

▲ Scrolls display content up

▼ Scrolls display content down

4

OK Restores right and left scrolling to initial position

2 Move up a line

5 Move down a line down

Toggles between compact display and complete display.

Compact

1/380

00001 27 18:46IF

00012 27 18:32IF

00217 27 18:30IF

00031 27 18:29IF

00016 27 18:27IF

00029 27 18:22IF

Complete

1/380

00001 05-27 18:46:21I

00012 05-27 18:32:09I

00217 05-27 18:30:52I

00031 05-27 18:29:01I

00016 05-27 18:27:55I

00029 05-27 18:22:08I

- 53 -

9

0

6 Toggle between Small and Large fonts.

00014 2006-5 1/23

27 08:30 12:10 13:20

18:08

26 08:46 12:15 13:25

18:23 18:55 22:20

25 08:53 12:07 13:19

18:23

Small Font

12:10

13:20 18:08

26 08:46 12:15

13:25 18:23

18:55 22:20

Large Font

Scrolls to the newest record

Scrolls to the oldest record

- 54 -

11

Cleaning the TQ600

1. Cleaning the Keypad and Display

Use a soft damp cloth to remove dirt. Wipe dry.

2. Cleaning the Optical Sensor

Clean the optical sensor as follows:

(1) Use a can of compressed air to blow off any loose dust or dirt particles on the sensor.

(2) Lightly press a small strip of adhesive tape to the sensor surface and slowly peel if off to remove dust & dirt particles.

(3) Use a soft, non-abrasive dry cloth to wipe the sensor surface. Be careful not to scratch the surface of the sensor. If there are lint particles on the sensor surface, use clear adhesive tape to remove particles.

Caution

:

Do not use any cleaners on the sensor or it could be damaged.

Cleaning products that contain alcohol or other strong chemicals may discolor or crack the terminal housing.

- 55 -

12

Troubleshooting

1.

Q: Fingerprint cannot be verified.

A: Possible Causes: The following conditions could result in a failed read.

1) Fingerprint is damaged or smooth

2) Finger is dry

Correction: Use 1:1 matching (see page 21). Moisturize finger.

Enroll a different fingerprint.

2.

Q: Terminal fails to communicate.

A: Possible Causes:

1) The communication port configuration is not correct; insure proper ports are connected.

2) Baud rate of the computer port and the terminal port are different.

3) The terminal has failed to connect with the power source or the computer;

4) The terminal is connected but failed to start.

5) The serial number of the linked terminal is not correct.

6) Data line or converter fails to communicate.

7) Failed computer COM port.

3.

Q: The display does not work or parts of it do not work.

A: Possible Causes:

1) Motherboard is defective

- 56 -

2) The LCD display is defective.

Correction: Contact your dealer or Acroprint for repair.

4.

Q: How do I remove a Supervisor?

A: Call Acroprint Technical Support.

5.

Q: The terminal beeps when the communication connection is made.

A: When using the RS-232 connection insure that the baud rate of the PC and terminal are matched.

6.

Q: Fingerprints have a high rejection rate.

A: Possible Causes:

1) Dirty sensor

2) Damaged sensor prism

3) Loose fingerprint reader connection

4) Damaged chip on PCB

Correction:

1) Clean sensor (see Cleaning instructions, Chapter 10)

2) Contact dealer or Acroprint for replacement of the prism.

3) Contact dealer or Acroprint.

4) Contact dealer or Acroprint.

7.

Q: The terminal is communicating, but the attendance records are not correct in the system.

A: Lower the baud to 19200 or 9600 and confirm if the records are correct.

- 57 -

Appendix

USB Flash Drive Management

Not available at this time.

Bell Schedule

The TQ600 has a bell signal that can be programmed for different times during the day. The bell schedule and bell duration can be set based on user requirements. A total of 20 bell schedules can be set.

The TQ600 has an internal electronic bell, see Chapter 5, “Power

Manage”.

- 58 -

Reserve Battery

(Mini-UPS)

In order for the TQ600 to function during power interruptions an optional 12V Mini-UPS (p/n 74-0169-000) is available. Contact your dealer or Acroprint to purchase.

UPS Operational State:

The UPS remains idle as long as AC Power is available but will automatically supply power to the TQ600 the instant AC Power is interrupted. When AC Power is restored the UPS will automatically charge until fully charged.

Connection

Note: Connect the Mini-UPS to the TQ600 first, then plug the UPS in and turn the power on.

Battery Storage:

Store batteries in a cool/dry place 50-86º F (10-30 º C). DO NOT store batteries for over 3 months and do not store them in direct sunlight, high temperature or high humidity. Charge the

- 59 -

batteries at least once every three months in order to maintain

50% of the rated capacity of the battery. Keep the batteries away from chemicals and heat sources.

Warning:

Batteries may leak, overheat, catch fire or explode if you don’t follow proper safety & handling: z DO NOT get batteries wet z DO NOT place batteries near heat sources z DO NOT use any charger other than the original charger z DO NOT inverse polarity connection z NEVER throw batteries into fire. Properly dispose of batteries according to local rules and regulations. z DO NOT allow anything to short circuit the batteries (connect the positive and negative terminals of the battery) z Dropping a battery may damage the battery. Replace the battery if you suspect that it is damaged.

Daylight Saving Time (DST)

The TQ600 ‘s time and date is set from the Server PC’s time and date.

If DST is enabled on the PC it will automatically update the time of all terminals that are connected to it. The TQ600 has no internal provision for DST.

- 60 -

Work Codes

Not available at this time.

- 61 -

Fingerprint Privacy:

1. The TQ600 merely captures points of the fingerprint but not the actual fingerprint image.

2. The fingerprint points cannot be used to create a fingerprint image.

3. Acroprint will not be liable for any direct or the indirect damages resulting from the use or inability to use our equipment.

4. If you have a question about privacy concerning the use of our equipment you should have your employer contact Acroprint.

- 62 -

06-0386-000

Revision A