Electrolux Floor-mounted stoves Service manual

SERVICE MANUAL

COOKING

© Electrolux Distriparts

Muggenhofer Straße 135

D-90429 Nürnberg

Germany

Fax +49 (0)911 323 1022

DGS-TDS-N

Edition: 05.09

Publ.-Nr.:

599 527 691

685

EN

Built-in appliances and floor-mounted stoves with „Vision Cooking“ input electronics

Table of contents

3.

3.1

3.2

3.3

3.4

1.

ESD=electrostatic discharge ................................................................................................... 3

2.

2.1

Software specifications, Functions .......................................................................................... 4

Illustration of the input electronics (UI) Vision Cooking ............................................................. 4

2.3

Main features of operation ........................................................................................................ 6

2.3.1

Clock setting following network reset ....................................................................................... 6

2.3.2

Child-proof lock ........................................................................................................................ 7

Functions of appliance ............................................................................................................. 8

Oven functions, capacities and small consumer - appliance-specific .................................... 8

Pyrolitical cleaning - Explanation .............................................................................................. 9

High-speed heating (Boost) - Explanation .............................................................................. 10

Safety function safety cutoff of oven ....................................................................................... 11

4.

Functional parts - Component data, installation situation, dismantling ................................... 12

4.1

Functional parts - Oven control .............................................................................................. 12

4.1.1

Input electronic (UI) Vision Cooking ........................................................................................ 12

4.1.2

Power electronic OVC2000 .................................................................................................... 13

4.1.3

Temperatursensor PT500 ...................................................................................................... 14

4.1.4.2 Door locking system, motorics with door-switch light ............................................................ 15

4.1.5

Door switch for the light .......................................................................................................... 16

4.1.6

Luminous bar in the control panel .......................................................................................... 17

4.1.7

Odour filter (catalytic converter electrically) ........................................................................... 18

4.2

Functional parts - Cooking setting control .............................................................................. 20

4.2.1

Power controller ..................................................................................................................... 20

5.

5.1

5.2

5.4

Technical equipment .............................................................................................................. 22

Temperature safety device ..................................................................................................... 22

Fan after-running .................................................................................................................... 22

Oven rack protective circuit .................................................................................................... 23

6.

6.1

6.2

6.3

Fault diagnosis/ What to do if ...? ........................................................................................... 24

Alarmmanagement (Faultcodes) ............................................................................................ 24

Measuring the temperature sensor ........................................................................................ 25

Demo Mode Input electronic Vision Cooking .......................................................................... 26

6.3.1

Activating / deactivating Version a .......................................................................................... 26

6.3.2

Activating / deactivating Version b .......................................................................................... 27

6.4

Factory test for appliances with meat thermometer pin ......................................................... 28

7.

7.1

7.3

7.7

Wiring diagram / measuring points ........................................................................................ 31

Connection Point Overview .................................................................................................... 31

Example circuit diagram OVC 2000 ....................................................................................... 32

Operative Equipment Overview .............................................................................................. 33

Changes ............................................................................................................................................... 36

DGS-TDS-N 05.09 A. B. © Electrolux - 2 599 527 691 EN

1.

ESD=electrostatic discharge

As the single electronic interfaces are not protected internally against statical electricity and are partially open, you must pay attention to that, in case of a repair, there will be a potential compensation via the housing of the appliance (touch it) in order to neutralize a possible charging and to prevent a damaging of the affected electronic interface.

You also have to be careful with those electronics delivered as spare parts, which have to be put out of the ESD protective package only after a potential compensation (discharge of possible statical electricity).

If a potential compensation with an existing static electricity is not executed, it does not mean that the electronic is demaged directly. Consequential damages may result due to the damaging of internal structures which arise only in case of load through temperature and current.

Endangered are all assembly groups which are provided with control entries, wire paths lying open and free-accessible processors.


2.

Software specifications, Functions

2.1

Illustration of the input electronics (UI) Vision Cooking

Displays symbol menu point

(incl. levels of use) time of day heating indication

Time functions Temperature

Weight

Symbol

Timer time of day duration

End

Start

Temperature

Weight

Fleischsonde

Odour filter

Display

(examples)

Functions

Timer is active.

Indicates the set time of day.

Indicates the required time for the boiling process.

Indicates the time when the boiling process will be finished.

End with plugged-in meat probe is being calculated.

Indicates the time since when the boiling process has been running.

Indicates the extent of oven heating.

Fast heating is active (reduced heating time).

Possibilities:

-Weight automatic system is active.

-Weight can be modified.

Possibilities:

-Meat probe is inserted.

-Meat probe automatic system is active.

-Core temperature can be modified.

Heat + Hold is active.

The odour filter has been activated.


Touch control sensor fields

On/Off Set values Selection

Options

Scroll

Main menu Confirm

Sensor field Function to the top/to the bottom above in the menu

Remark

With an active function:

- Press 1 x: Change to superior menu (function remains active), after 5 seconds again.

Change into active menu point.

- Press 2 x: In the superior menu downward and upward (function is deactivating).

Set functions are deactivating (besides timer).

Display main menu

Confirm

Switch on or off appliance

Time functions, Select additional functions and meat probe.

Set values (e.g. temperature, *Activate value: time, weight, boiling level) -press 1 x: symbol standing in front is flashing.

-2press 2 x: value can be set.

*Activate value:

-press 1 x: set value in single steps.

-Keep key pressed: set value in fast steps.

*When setting a period and time respectively you can reset the display to cero by pressing + and simultaneously.


2.3

Main features of operation

2.3.1 Clock setting following network reset

Information: The oven only functions with set time!

When connecting the appliance again, e.g. after a repair, you need not set the time anew, as the electronic remember the time even for a longer period of time because of its technology

(condenser).

If a new input electronic is installed, or if the appliance is disconnected from power supply for a longer time, you have to proceed as follows for setting the time:

Set language

1.

After electric connection the display indicates the following:

-

the company logo the software version and working time

the display "set language"

2.

Select the desired language by "-" and "+" respectively

3.

Confirm the selected language by "OK".

Immediately you can see the texts in the set language in the display .

Set contrast and brightness

After setting the language you can see the displays "set contrast" and "set brightness". Contrast and brightness are set according to the language (see section "Set language").

Set clock

After setting contrast and brightness, the display indicates "set time of day".

1.

Set the hour of the current time by "-" and "+" respectively.

2.

Confirm by "OK".

3.

Set the current time by "-" and "+" respectively.

4.

Confirm by "OK".


2.3.2 Child-proof lock

The key block does not protect against unintentional switching off. After switching off the appliance the key block is canceled again.

When the child-proof lock has been activated, the appliance can not be put into operation.

Activate child-proof lock

No function may be selected.

1.

Touch "selection options" and "-" simultaneously until you can see a message. Child safety function is active.

Child safety function switch off

1.

Touch "selection options" and "-" simultaneously until you can see a message. Deactivate the child lock. Now the child lock is deactivated and the oven is in operation again.


3.

Functions of appliance

3.1

Oven functions, capacities and small consumer - appliance-specific pos. oven function

0 off

1 ring+fan

2 top+bottom

3 ring+bottom+fan

4 grill+top+fan (alter)

5 grill

6 grill+top

7 bottom

8 ring+fan (LTC) def. temp.

Boost

180

200

200

180

300

300

150

120/80

-

-

-

-

-

A

A

A

MP x x x x x x x x

ResH.

KeepW.

grill element heating elements (Watt) top element bottom element

1900 1000 1000 rear element

2400 x

-

-

x x x x x

x x x x x x

-

-

X

X

-

-

-

X

-

-

-

X

-

X

-

X

X

-

-

-

-

X

X

-

-

X

-

-

X

-

X

cooking fan

40 small loads (Watt) cooling fan oven lamp back wall oven lamp side wall max power

(W) current (A)

25 40 25

-

X

-

-

X

-

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

2530

2090

3530

3030

1990

2990

1090

2530

11,0

9,1

15,3

13,2

8,7

13,0

4,7

11,0

A

Boost (AUTO) ring+fan X X X X X 2530 11,0 pos. oven function

0 off

1 ring+fan

2 top+bottom

3 ring+bottom+fan

4 grill+top+fan (alter)

5 grill+top+fan+tsp (alter)

6 grill

7 grill+tsp

8 grill+top

9 grill+top+tsp

10 bottom

11 ring+fan (LTC) def. temp.

Boost

180

200

200

180

180

300

300

300

300

150

120/80

-

-

B

-

A

A

-

A

-

-

-

MP x x x x x x x x x x x

ResH.

KeepW.

grill element heating elements (Watt) top element bottom element

1900 1000 1000 rear element

2400

-

x

x x x x

x

x x x x x x x x x x

-

X

X

X

X

-

X

-

-

X

-

-

-

X

X

-

-

X

-

X

X

-

-

-

-

-

-

X

-

-

X

-

X

-

-

-

-

-

X

-

X

-

-

-

X cooking fan

40 small loads (Watt) cooling fan oven lamp back wall lamp side wall

25 40 25 turnspit

5 max power

(W) current (A)

-

-

X

-

X

X

X

-

-

-

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

-

X

-

-

-

-

-

X

-

-

2530

2090

3530

3030

3035

1990

1995

2990

2995

1090

2530

11,0

9,1

15,3

13,2

13,2

8,7

8,7

13,0

13,0

4,7

11,0

A

B

Boost (AUTO) ring+fan ring+fan+tsp

-

-

-

-

-

-

X

X

X

X

X

X

X

X

X

X

-

X

2530

2535

11,0

11,0 heating element (Watt) small loads (Watt) pos.

oven function def. temp.

Boost grill element top element bottom element rear element cooking fan cooling fan oven lamp back wall oven lamp side wall turnspit max. power (W) current (A) off ring + fan top + bottom ring + bottom + fan grill + top + fan (alter) grill + top + fan + tsp (alter) grill grill + tsp grill + top grill + top + tsp bottom ring + fan (LTC)

Boost (auto) ring + fan ring + fan + tsp


3.2

Pyrolitical cleaning - Explanation

° C

500

400

end of heating phase cooling phase

300

door locked

200

door unlocked

100

room temperature

min

90 120

P3

150

P2

Fig. heating-up curve temperature (°C) / time (min

P1

With the Pyroluxe self-cleaning system the residues in the interior are carbonized to ashes at high temperatures. The centre of gravity temperature of the muffle is approx. 500°C.

A max. selection of three pyrolysis durations (P…) can be made per appliance class and equipment.

Pyrolysis duration (Heating period)

P1 (Heavy)

P2 (Normal)

P3 (Light)

Note:

>

>

>

Heating period

Heating period

Heating period

150min

120min

90min

In appliances which are equipped with two pyrolysis durations, P2 corresponds to the pyrolysis duration P3.


The oven door is locked at a centre of gravity temperature of the muffle of approx. 312°C, after a heating-up time of approx. 11 min.

The oven door is unlocked at a centre of gravity temperature of the muffle of approx. 204°C. The moment depends on the selected pyrolytic duration.

The cooling fan is running at an increased speed until the moment of unlocking. At a centre of gravity temperature of the muffle of approx. 130°C it switches off.

Attention écart pour les appareils stationnaires

3.3

High-speed heating (Boost) - Explanation

Explanation: Quick-Heating means reaching the selected oven temperature as quickly as possible.

After reaching the oven temperature, it switches back to the originally selected oven function (heating element configuration).

The Quick-Heating function is displayed depending on the appliance either by a symbol or by animated bar.

Note: Quick-Heating function - manual operation

Quick-Heating function „AUTO“ - Automatically active, not switchable

The type of Quick-Heating function (Boost) available is in Chapter 3.1.


3.4

Safety function safety cutoff of oven

If the oven is not switched off after a specific period of time or if the temperature is not changed, then it switches off automatically.

The oven switches off at an oven temperature of:

Putting into operation after a safety cutoff:

In the display you can see the indication „automatic safety disconnection system active“. Continue by OK.

Note: The safety cutoff is cancelled, when the clock function „duration“ or „end“ has been set.

Furthermore, it is not active with the functions, low-temperature cooking and Pyrolyse.


4.

Functional parts - Component data, installation situation, dismantling

4.1

Functional parts - Oven control

4.1.1 Input electronic (UI) Vision Cooking

In addition to diverse semi-conductor modules, the Vision Cooking input electronics mainly includes a LCD display and a microprocessor. This controls the electronic control unit via a personalised program. The desired oven functions are set by a so-called touch board which is a common spare part with the control panel.

Fig.: user interface in built-in condition

Fig. 1 Fig. 2 Fig. 3

The user interface is positioned firmly in a plastic housing (E-box). The whole unit is locked in the panel support. When opening the appliance please pay attention to that the control board for the luminous bar is fixed in the control panel from below to the front housing lid (figure 1). After drawing off the lines you can disassemble the front cover lid. After pressing in the four hooking noses at the bottom side of the plastic housing (figure 2) you can remove the user interface to the back, in direction of the interior of the appliance (figure 3). With upright stoves, there may be different scenarios of fitting positions.


4.1.2 Power electronic OVC2000

Connections for

-

meat thermometer

- Temperature sensor

- door lock

- telescopic bars

- data link

Power supply

50....60Hz

230V AC

R

elay for

-

door lock

- lighting

- fan, moto

R

elay for

-

all-pole cutoff

Fig.: Powerboard OVC2000 wired in the appliance

Fig.: assembly situation Fig.: Spare part OVC2000

The power electronics are located on the rear side of the appliance and are accessible after removing the housing rear panel. The power board is installed in a so-called „functions box“ made of plastic. These two components, power electronics and plastic box, are also a replacement part unit (see Ill.)

Please refer to Chapter 7 for connection designations and possible measuring points.


4.1.3 Temperatursensor PT500

-

-

The temperature in the baking oven is measured by a temperature sensor (type PT 500) for appliances with control board. The sensor is provided at the rear of the appliance. It is used to

transmit to the electronic systems the values for: cyclic heating the radiators until the selected temperature is reached; switch off the radiators in case of overheating of defective sensor; switching ON/OFF the cooling fan.

Fig. Temperature sensor

Fig. Electrical resistance of sensor depending on the ambient temperature


4.1.4.2

Door locking system, motorics with door-switch light

Drive motor

Fig.: Door locking system as complete component

Curve pane

Double micro switch

Above: Lock

Below: Oven lighting switch

Sliding micro switch - Lighting

Sliding door locking system


4.1.5 Door switch for the light

Switch axis

Electrical terminals

When opening the door of the oven, the lighting of the oven is activated over this component after the device has been switched on. The mounting position is at the top and right-hand corner of the front frame of the oven


4.1.6 Luminous bar in the control panel

Figures show the luminous bar as a separate component and the electric terminals from the sight of the interior of the appliance, each at the left and at the right. The assembly situation is in the switch panel support. For disassembling the luminous bar you have to remove the switch panel.

The luminous bar is selected by a selection electronic system which is mounted at the bottom side to the front cover of the appliance. It supplies the luminous bar with the supply voltage of 7 V / 18 mA.


4.1.7 Odour filter (catalytic converter electrically)


-

-

-

In order to disassemble the odour filter in case of a defect, you must proceed as follows:

Disassemble the appliance, open the housing lid

Disassembly of the air channel upper part (figure 1 + 2).

Loosen the six connecting screws air channel lower part / adapter odour filter (figure 3)


-

-

-


Remove the air channel lower part (figure 4).

Loosen the four connecting screws adapter odour filter / odour filter (figure 5).

Remove the adapter odour filter (figure 6).


Loosen the four connecting screws odour filter / oven muffle (figure 7). It is also necessary to cut the oven insulating in order to remove the odour filter (figures 8 + 9).

When assembling the odour filter please proceed in the reversed order and pay attention to the careful combination of the oven insulating.


4.2

Functional parts - Cooking setting control

4.2.1 Power controller

Fig. Power controller Fig. Switch in „OFF“ position

Input voltage 230 V

Fig. Performance characteristic

K1 – Knob position

% ED – Switching on period in percent

100 % corresponds to a switching on period of 41 seconds

The hot plates are controlled via the bimetallic contact P 1-2. The input voltage of 230 V is applied here.

Depending on the position of the knob, this contact determines how often the hot plate is switched on or off during a certain unit of time by cycling the maximum heating power (230 V or 0 V between contact 2 and 4) (refer to performance characteristic).

Continuous operation at max. heating power is hot plate 9.

The power characteristic shows the power controller in cycling mode.

The average switching on period for each knob position can be read off in % of the cycled and/or max. power.


Dual circuit heating element

Dual circuit regulator


5.

Technical equipment

5.1

Temperature safety device

With built-in appliances, there is a temperature fuse on the side of the air channel that switches off the appliance in the event of overheating. The measured temperature value during a cutoff is 90°C.

Fig.: Built-in position - Temperature fuse

Notes:

-

for wiring diagram see chapter 7

Deviations possible with floor-mounted stoves

5.2

Fan after-running

The cooling fan switches on automatically when putting the appliance into operation. First it is in operation to keep cool the appliance surfaces. After the oven was switched off, the fan continues running to cool the appliance and then switches off automatically at a centre of gravity temperature of the muffle of approx. 120°C-130°C. The post-operative ventilation is controlled via the electronics.

Note:

-

for wiring diagram see chapter 7

Deviations possible with floor-mounted stoves


5.4

Oven rack protective circuit

Appliances with Pyroluxe self-cleaning system are provided with a microswitch. Dieser Mikroschalter befindet sich an der linken äußeren Seite der Komponentenplatte. Only with attached oven racks, not with slide-in grids, the microswitch interrupts a switch contact which prevents an activating of the pyrolytic function.

Note: for wiring diagram see chapter 7


F91

F12

F13

F14

F15

F16

6.

Fault diagnosis/ What to do if ...?

6.1

Alarmmanagement (Faultcodes)

Alarmmanagement Powerboards Prisma, OVC1000 und OVC2000

F6

F7

F8

F9

F10

F94

F4

F5

F95

F96

Display

F0

F1

F2

F3

F11

Description of fault Fault repair

Internal error door cannot be locked door cannot be unlocked replace power electronics

Test door locking system

Test door locking system and unlocking thermostat f11 software error Execute network reset by disconnecting the appliance from the electricity supply and restarting

Temperature sensor alarm - resulting in F4 Test temperature sensor, replace if necessary

Temperature sensor without contact or short circuit Test temperature sensor, replace if necessary

Clotted heating element relay contacts on the power electronics

Temperature alarm at power electronics - resulting in F6

Temperature alarm at power electronics - resulting in F6

Power electronics temperature too high

Replace power electronics

Test built-in situation of the ventilation channel and the function of the cooling fan



Correctly connect the appliance and re-start Faulty electrical connection (only in appliances with Prisma power electronics)

No connection between power electronics and input electronics

Micro processor resets itself independently (=

Reset)

Triac on power electronics defect

Check connection line - replace electronic systems if necessary

Execute network reset by disconnecting the

Meat skewer sensor without contact or shortcircuited appliance from the electricity supply and restarting

Activate Main Button, select an operation modus with hot air, wait for cooling ventilation start, replace power electronics again in the event of an error report following approximately 20 seconds

Check meat thermometer, also check bushing and wiring if necessary; if all this OK replace power

Temperature sensor alarm for steam generator - resulting in F12

Temperature sensor of steam generator without contact or short-circuited

Internal electronics error electronics

Test temperature sensor, replace if necessary

Test temperature sensor, replace if necessary

Replace power electronics software error

Internal electronics error

Replace input electronics

Replace input electronics

Combined alarm Pyrolytic cleaning/cooking zone Replace input electronics


6.2

Measuring the temperature sensor

If a failure at the temperature sensor is assumed, the resistance can be checked by means of an ohmmeter.

The resistance of the temperature sensor should be 500 – 600 ohms at room temperature.

Make sure to measure the insulation resistance between the metallic housing and each connection terminal.

The resistance should be higher than 2 MOhms.

Abb. Measuring the temperature sensor


6.3

Demo Mode Input electronic Vision Cooking

Both demo mode versions possible.

6.3.1 Activating / deactivating Version a

The following steps (1-3) should be done within 10 sec.

1.

Oven in OFF state

2.

Keep pressed Mainswitch for 5 seconds until oven switches OFF again.

A signal is audible

3.

Keep pressed “Timer-” and “Minus-” key simultaneously for 1 second.

Sound: beep, beep, beep…confirms

4.

Once oven is switched ON “DEMO” is displayed.

Deactivation vice versa

After 10 sec. or once another key has been pushed Demo Mode can’t be activated anymore, but procedure can be started from the beginning.


6.3.2 Activating / deactivating Version b

Fig. 1

Start position:

Display:

The appliance must be switched off.

"Time" (fig. 1).

Operating step 1: Press the main switch for 5 seconds (fig. 1), the appliance switches itself "ON" and then "OFF" again.

Display: "Standby" (fig. 2) ---> "Time" (fig. 3).

Acoustic signal: 1x "Beep" as confirmation.

Fig. 2

Fig. 3

Operating step 2:

Acoustic signal:

Simultaneous pressing of the two buttons "Timer" and "Minus" for 2 seconds (fig. 4).

3 x "Beep" as confirmation.

Fig. 4

Operating step 3:

Display:

Switching the appliance on with the main switch active Demo Mode deactivated Demo Mode

---> "DEMO" (fig. 5).

---> none (fig. 6)

Fig. 5

DGS-TDS-N 05.09 A. B. © Electrolux

Fig. 6

- 27 599 527 691 EN

6.4

Factory test for appliances with meat thermometer pin

The factory test can only be activated during the display of the brand logo, after the appliance has been connected anew!

Actuate the touch pads simultaneously until you can hear a signal (beep). The factory test starts with the

---> consumer test

Depending on the appliance group (see tables) you can switch through various consumers in five steps and check them for function by using the touch pad. This cycle can be repeated as often as desired.

symbol is indicated in the display

1

2*

3

4

5

1

2*

3

4

5

1

2*

3

4

5

1

2*

3

4

5 x x x x x x x x x x x x x x x x x x x x x x x x x x x x slowly slowly slowly slowly slowly slowly fast slowly slowly slowly slowly fast slowly slowly fast slowly fast slowly slowly fast x x x x x x x x x x x x x x x x x


Continue by using the touch pad

---> temperature sensor test

The current oven temperature is measured and indicated in the display.

---> meat thermometer test

-

Insert the meat spit into the respective plug socket, the currently measured temperature of the meat thermometer is indicated.


-

-

-

---> information on the input electronic version

Following information is indicated one after the other: firmware version of input electronic configuration version of input electronic working time of oven

Example

EBAIB205

V02IB012

0


-

-

-

-

---> display Test complete indication of display display completely dark complete display in checker pattern indication of single pixels


---> display brightness

By the touch pads "+" and "-" you can set the brightness of the display.



---> door locking test

is automatically started with appliances with pyrolisis.

In order to operate the appliance normal again and to leave the factory test respectively you must disconnect it from the mains and connect it again!


7.

Wiring diagram / measuring points

7.1

Connection Point Overview


7.3

Example circuit diagram OVC 2000


7.7

Operative Equipment Overview

E

F f1 f1.1 f2 f2.1 f5 f6 f7 f8

A1

A2 b3

BOF

BOT c4

D

DS e1 e11 a31 a32 a33 a34 a61 a62 a73 a84

Kennzeichen a1 a2 a3 a4 a7 a7.1 a8 a15 f33 f34

G5 h1 h1.1 h1.4 h1.5 h1.6 h1.7 f11 f12 f15 f16 f19 f21 f22 f31 f32

EN

Description

Switch 7-step front left

Switch 7-step rear left

Switch 7-step rear right switch 7-step front right

Heating mode selector main oven

Heating mode selector top oven

LTC(Low Temp. Cooking) switch

Touch electronic switch warming zone energy regulator front left energy regulator rear left energy regulator rear right energy regulator front right touch electronic switch front left touch electronic switch rear left touch electronic switch rear right touch electronic switch front right actuator exhaust

Actuator desteam

Socket meatprobe mode selector function mode selector temperature interference filter hob connector 12-pol. door switch

Door look pyro

Distributor plate pot detection hob connector 8-pol. hob connector 21pol

Main oven thermostat

Top oven thermostat safety temp. limiter main oven safety temp. limiter top oven

Thermostat cooling fan delay

Thermostat fast run cooling fan pyro sensor to magnetron

LTC(Low Temp. Cooking) termostat

Thermostat unlock pyro

Thermostat cooling fan delay

2. safety temp. limiter oven thermostat overheating warning rack thermostat saftey temp. limiter grill saftey temp. limiter fryer residual contact front left residual contact rear left residual contact rear right residual contact front right magnetron

Lamp working lamp working top oven lamp working hot plate front left lamp working hot plate rear left lamp working hot plate rear right lamp working hot plate front right


Q1 r6 r7 r7.1 r8 r8.1 r11 r12

N1

N2

N3

N4

N5

PE3

PE4

PE/1b m1 m2 m3 m4 m5 m6 m8 m12 m13 m20

M2

M3

M4

M5

KS2

KS3

KS4

M1 h10 h11 h12 h20 h30 h40 h52

K k1

KS

KS1

Kennzeichen h3 h3.1 h4 h4.1 h4.6 h5 h5.1 h7 h9

EN

Description lamp heating main oven lamp heating top oven oven lamp main oven oven lamp side main oven lamp halogen oven lamp top oven oven lamp side top oven meatprobe display lamp overheating analog timer electronic timer

6-push electronic timer timer primary code hob residual lamp display board display oven clutch

LTC(Low Temp. Cooking) relay switch child safety rotary hot plate front left rotary hot plate rear left rotary hot plate rear right rotary hot plate front right

Hob connector 14-pol. 1+2

Hob connector 14-pol. 3+4

Connector 11-pol.

Connector 7-pol.

Connector 3-pol.

fan hot air fan cooling transformer halogen lamp transformer timer transformer electronic motor stirrer transformer high voltage turnspit motor

Ignition coil gas cooling fan, L3 electronic powerboard modul of induction electronic board Rhea connector board

Power supply unit lightbar ground point front frame left ground point front frame right ground point component plate quick start module top oven top heating/grill combination main oven top heating element top oven top heating element main oven bottom heating element top oven bottom heating element fat and smell thermal switch


s14 s19 s21 s22 s23 s31 s32 s33 s34

TR

X1

X10

X11

X12 x20 r33 r34 r35 s1 s2 s3 s4 s11 s12 s13

Kennzeichen r14 r14.1 r15 r16 r19 r20 r21 r22 r27 r27.1 r31 r32

EN

Description main oven grill heating element top oven grill heating element warming zone rear rack heating preresistor cooling fan heater grill heater fryer preresistor oven lamp preresistor oven lamp side cooking plate front left cooking plate rear left cooking plate rear right cooking plate front right cooking plate middle sensor pot detection front left sensor pot detection rear left sensor pot detection rear right sensor pot detection front right micro switch gas to electro micro switch grill to fryer micro switch grill socket micro switch sensor rack switch sensor grill sensor fryer

Sensor wok (middle)

Ignition switch front left

Ignition switch rear left

Ignition switch rear right

Ignition switch front right telescopic runner switch main terminal tandem pin shells 6-pol. tandem pin shells 8-pol. connector hob frame connector, L3


Changes

Pages 24, Chapter 6.1

changed


Electrolux Floor-mounted stoves Service manual

SERVICE MANUAL

COOKING

1.

ESD=electrostatic discharge

2.

Software specifications, Functions

Symbol

(examples)

Functions

Touch control sensor fields

3.

Functions of appliance

° C

500

400

300

200

100

min

4.

Functional parts - Component data, installation situation, dismantling

-

50....60Hz

230V AC

R

-

R

-

When assembling the odour filter please proceed in the reversed order and pay attention to the careful combination of the oven insulating.

5.

Technical equipment

6.

Fault diagnosis/ What to do if ...?

Alarmmanagement Powerboards Prisma, OVC1000 und OVC2000

Both demo mode versions possible.

7.

Wiring diagram / measuring points

Changes

Related manuals

HQ

W7-54910-HQN

Electrolux

Floor-mounted stoves

Trotec

TDS 20 R

Trotec

TDS 10 P, TDS 20 P Electric Heater

Trotec

TDS 20 C

Table of contents