advertisement
MGP D5
User Guide
B4100515 - 00
October 2004
www.barco.com
User Guide TABLE OF CONTENTS
TABLE OF CONTENTS
INTRODUCTION ..................................................................................... 4
SAFETY & WARNINGS ........................................................................... 5
REMOTE CONTROL............................................................................... 13
CONNECTOR PANEL ............................................................................. 16
SETUP COMPUTER ............................................................................... 19
IMAGE ADJUSTMENTS ......................................................................... 20
CEILING MOUNT (option) ................................................................... 21
USING THE PROJECTOR........................................................................ 23
MENU SYSTEM .................................................................................... 25
MOUSE CONTROL ................................................................................ 37
RS 232 AND LAN CONTROL ................................................................ 38
TROUBLESHOOTING............................................................................. 39
MAINTENANCE.................................................................................... 41
LAMP CHANGE.................................................................................... 43
SERVICE INFORMATION....................................................................... 46
TECHNICAL DATA................................................................................. 47
DECLARATIONS.................................................................................... 54
MGP D5 3
4
INTRODUCTION User Guide
INTRODUCTION
This digital projector is designed with the latest state-of-the-art technologies in illumination, imaging, optics, electronics, thermal and industrial design in order to serve traditional as well as novel imaging applications across a variety of markets, offering features such as:
• 1400x1050 pixel SXGA+ DLP™ technology
• Single chip DMD™ with DarkChip2™ technology by Texas
Instruments®
• HIGH CONTRAST for vibrant colors and deep blacks
• HIGH RESOLUTION for unprecedented detail
• HIGH BRIGHTNESS for larger screens
• DEEP BLACKS for maximum detail
• REDUCED IMAGE NOISE through high end signal processing
• FAROUDJA DCDi™ Video processing and de-interlacing
• ECO MODE for reduced power consumption and lower audible noise
• VARIABLE LAMP POWER for alignment of multi-screen configurations
• LONG LIFE LAMP (up to 4000 hours) in low power ECO mode
• STYLISH AND COMPACT DESIGN to fit most applications, installed or movable
• SIX VIDEO and GRAPHICS INPUTS for virtually any video and data source
• LAN, RS232 and USB ports for control and monitoring
The specifications and functionality of the product may change without prior notice.
MGP D5
User Guide SAFETY & WARNINGS
SAFETY & WARNINGS
This user guide contains important information about safety precautions and the set-up and use of the projector. Please read the manual carefully before you operate the projector.
SAFETY
This device complies with relevant safety regulations for data processing equipment for use in an office environment. Before using the projector for the first time, please read the safety instructions thoroughly.
WARNING
Use only the cables and cords supplied with the projector or original replacement cables. Using other cables or cords may lead to malfunction and permanent damage of the unit.
Always use 3-prong power cord to ensure proper grounding of the unit. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.
Never open the unit. The projector contains no user serviceable parts. Refer all repairs to qualified personnel only.
Make sure that no objects enter into the vents and openings of the set. Do not spill any liquids on the projector or into the vents or openings of the unit.
Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens.
Do not look into the projection lens when the projector is switched on. The strong light may permanently damage sight.
Do not look into the laser beam when activated on the remote control. Laser light may permanently damage sight. Do not point laser beam on people.
MGP D5 5
SAFETY & WARNINGS User Guide
Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
Do not drop the projector.
Always operate the projector horizontally, within the range of the adjustable rear feet. Operating the unit in other positions may reduce lamp life significantly, and may lead to overheating, resulting in malfunctioning.
Always allow ample airflow through the projector. Never block any of the air vents. Never cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating. Minimum safety distance to any side of the unit is 50 cm/20" in any direction.
CAUTION! Hot air is exhausted from the side vent. Do not place objects that are sensitive to heat nearer than 50 cm/20" to the exhaust vent.
The projector is designed for indoor use only. Never operate the unit outdoors.
Do not operate the projector outside its temperature and humidity specifications, as this may result in overheating and malfunctioning.
Only connect the projector to signal sources and voltages as described in the technical specification. Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit.
Allow the unit to cool down for 60 minutes before lamp change.
6 MGP D5
User Guide SAFETY & WARNINGS
INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES
RELATED TO MERCURY VAPOR
This projector is using an extremely bright UHP™ lamp for illumination to attain the desired high brightness image.
This technology is similar to other high-pressure discharge lamps that are extensively used in cars, street lights and other lighting appliances today. These lamps, like fluorescent lighting, contain small amounts of mercury. The amount of mercury present in a lamp is far below the limits of danger set by the authorities.
It is very important that lamps containing mercury are treated properly to minimize potential health hazards.
The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when operating. While the lamp and the projector are carefully designed to minimize the probability of lamp rupture, the lamp may break while operating and small amounts of mercury vapor may be emitted from the projector.
The probability of rupture increases when the lamp reaches its nominal life. It is therefore highly recommended that the lamp is replaced when the rated lifetime is reached.
As a general precaution, secure good ventilation in the room when operating the projector. If lamp rupture occurs, evacuate the room and secure good ventilation. Children and pregnant women in particular should leave the room.
When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.
Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people under certain conditions.
According to the Public Health Statement for Mercury published by the Agency for Toxic Substances and Disease Registry
("ATSDR", part of the United States Public Health Service), the brain, central nervous system and kidneys are sensitive to the effects of mercury, and permanent damage can occur at sufficiently high levels of exposure. Acute exposure to high concentrations of mercury vapor can cause conditions such as lung and airway irritation, tightness in the chest, a burning
MGP D5 7
SAFETY & WARNINGS User Guide sensation in the lungs, coughing, nausea, vomiting and diarrhea.
Children and fetuses are particularly sensitive to the harmful effects of metallic mercury to the nervous system.
Seek medical attention if any of the above symptoms are experienced or if other unusual conditions are experienced following lamp rupture.
REMOTE CONTROL WARNING
Laser radiation class II product; wavelength 670nm; maximum output 1 mW.
Remote control complies with applicable requirements of 21 CFR
1040.10 and 1040.11.
Remote control complies with applicable requirements of EN 60
825-1: 1994 + A11
LASER RADIATION WARNING
CAUTION
: Laser radiation. Do not stare into the beam.
Laser diode: Wavelength 570 mm, max. output 1 mW.
Class II laser product.
8 MGP D5
User Guide
OVERVIEW
A
Focus ring
B
Zoom ring
C
IR sensor
D
Ventilation
E
Keypad
F
Connector panel
G
Power connector
H
Lamp house
I
Adjustable foot
J
Foot release
K
Security lock
L
Ceiling mount
OVERVIEW
MGP D5 9
KEYPAD
KEYPAD
AUTO
MENU
SOURCE
VOLUME +
User Guide
SOURCE
POWER
STATUS
VOLUME –
POWER
Switches the projector between on and standby modes. Press firmly (1 sec) to switch on. Press firmly (1 sec) twice to switch off.
AUTO
Adjusting the projector to display a correct image, including position, width, height, contrast, brightness and overall stability.
MENU
Activates the menu system. Use the four arrow keys to navigate and to activate.
/
Select menu option when menu system is activated. Activates the keystone correction when the menu system is not in use. Use the four arrow keys to adjust horizontally and vertically.
SOURCE
Use the two arrow keys to select source when keystone correction and menu system is not activated.
10 MGP D5
User Guide KEYPAD
VOLUME
Use the two arrow keys to adjust the sound volume.
STATUS
This is an indicator light, not a key. Do not push. It indicates the current projector status. See STATUS chapter for detail.
MGP D5 11
STATUS
STATUS
User Guide
POWER
STATUS
12
PERMANENT GREEN LIGHT
The projector is turned on and in normal operation.
PERMANENT YELLOW LIGHT
The unit is in standby mode; no source(s) connected, or the source(s) connected are inactive or switched off, thereby activating the power-save function (DPMS). You may enable or disable the power save function in the SET UP sub menu, DPMS on or off.
FLASHING YELLOW LIGHT
Please wait. The yellow light will flash a period after power cord is connected (10-15 sec.), and a period after going to standby mode while lamp is cooling down (approximately 45 sec.). The projector may not be turned on again until the light has turned to permanent yellow.
PERMANENT RED LIGHT
Lamp life has expired. Please change projection lamp immediately. Failing to change lamp may lead to lamp explosion.
FLASHING RED LIGHT
Projector is overheated. Turn off immediately! Check if air inlets are covered or if ambient temperature is outside specifications.
The projector can not be restarted unless the power cord is disconnected and reconnected again. If the projector continues to flash red, you will need to return the unit for service.
MGP D5
User Guide REMOTE CONTROL
REMOTE CONTROL
The remote control allows flexible access to the projector settings, either through direct keys, or through the menu system.
The remote control can be used to emulate the computer mouse through the USB interface.
POWER
Switches the projector between on and standby modes.
AUTO
Adjusting the projector to display a correct image, including position, width, height, contrast, brightness and overall stability.
OSD
Toggle On Screen Display (OSD) feedback of and off. When on, all user commands are echoed on screen. When off, user commands will not be echoed on screen.
INFO
Displays source and projector status on screen.
VIDEO
Selects the composite video input as signal source
S-VIDEO
Selects the super video input as signal source
MGP D5 13
REMOTE CONTROL
YPbPr
Selects component video input
DVI
Selects the DVI input
VGA 1
Selects the VGA 1 input
VGA 2
Selects the VGA 2 input
STILL
Toggles between live and still (frozen) image
AV MUTE
Toggles between live and no (muted) image
BRIGHT
Adjusts image brightness from dark to bright
CONTRAST
Adjusts the image contrast from soft to hard
COLOR
Adjusts the color of the image from pale to saturated
VOLUME
Adjusts the sound volume
ASPECT
Cycles through the aspect ratios available with the current source
MENU
Toggles the menu system on and off
User Guide
14 MGP D5
User Guide
TRACKBALL
When USB cable is connected between PC and projector, the trackball is used to move the mouse pointer when not in the menu. Use the trackball to navigate between options when in the menu.
LEFT/SELECT
Use as mouse LEFT key when not in the menu. Use as SELECT key when in the menu
RIGHT
Use as mouse RIGHT key
LASER
Activates the built-in laser pointer.
CAUTION! Do not point laser beam at people. Do not stare into laser beam.
ARROW KEYS
Use the four arrow keys as alternatives to the trackball for menu navigation
SELECT
Select option in menu. Same function as
LEFT/SELECT above.
REMOTE CONTROL
MGP D5 15
CONNECTOR PANEL
CONNECTOR PANEL
User Guide
16
A YPbPr:
Used for high quality video reproduction.
B S-VIDEO:
Used for improved quality video.
C C-VIDEO:
Used for standard video quality.
D DVI-D - Digital RGB:
For a low noise computer and video image.
E Monitor VGA out:
Allows for connection to local VGA monitor or daisy-chaining of several projectors using VGA. Works with
VGA inputs only.
F VGA - Analog RGB 1-2:
The standard analog computer graphics interface.
G RS 232 control in-out:
Allows for wired remote control and monitoring of many projector functions used in installation environments. The secondary output connector allows for daisy-chaining, enabling both individual and global control and monitoring of multiple projectors.
H Audio in 1-2:
Allows for connection of up to two audio sources simultaneously.
I Audio out:
Connection to external audio system.
J RC:
Allows connection of external IR receiver or wired remote control.
MGP D5
User Guide CONNECTOR PANEL
K USB - interface:
Allows for computer mouse control.
L LAN:
Provides access to control and monitoring over a Local
Area Network.
M Mains power connector:
Use only three-prong, grounded power cord.
MGP D5 17
SET UP VIDEO User Guide
SET UP VIDEO
Before setting-up, switch off all equipment.
Three video sources may be connected, using the YPbPr
(component), S-VIDEO (super video) and VIDEO (composite video) inputs.
Component video will display more detailed images. Composite video yields images with less detail.
In addition, the DVI-D input can be used with video sources (DVD player fitted with an HDCP
TM
compliant DVI or HDMI connector) for a pure digital connection.
Connect the power cord.
18 MGP D5
User Guide SETUP COMPUTER
SETUP COMPUTER
Before setting-up, switch off all equipment.
The projector may be connected to up to three computer sources simultaneously, using the VGA and DVI inputs.
The VGA interface is analog and may cause some noise in the projected image, depending on the signal quality from the VGA graphics card in the computer.
The DVI (Digital Visual Interface) interface is all-digital and will yield a projected image with very low noise.
Connect the USB cable to allow for remote mouse control.
Connect the power cord.
Connect the RS232 interface to allow for individual or global control of multiple units in a daisy chain configuration.
Connect the LAN connector for individual control and monitoring of multiple projectors over LAN.
MGP D5 19
IMAGE ADJUSTMENTS
IMAGE ADJUSTMENTS
Turn the FOCUS (A) and ZOOM (B) rings on the projection lens to get a correctly sized and focused image. If the desired image size is not achieved by zooming, relocate the unit nearer or farther away from the projection screen and refocus.
To adjust the projected image to the desired height on the screen, eject the front foot (C) by pressing the release button (D), and adjust the angle to the right position.
When the image is shifted up, the so-called 'keystone' effect appears as an optical distortion of the image. You may compensate this effect by the KEYSTONE correction control on the keypad or remote control.
To get an image level with the screen, turn the rear feet (E) to the right position.
User Guide
20 MGP D5
User Guide CEILING MOUNT (option)
CEILING MOUNT (option)
CEILING MOUNT KIT
Please refer to the “MSP-BAR034” installation instructions included in the ceiling mount kit package.
The projector is provided with 3 threaded inserts (L) to attach the
UPA interface bracket of the ceiling mount kit.
CEILING MOUNT COVER
The auxiliary cable cover can be mounted on the projector to conceal the interface cables and power cord when the unit is ceiling mounted.
Connect all cables and fix them in place before the cable cover is attached to the projector.
1. Loosen the rear adjustable feet by unscrewing them.
2. Align the vertical hooks on the cover with the guides on the rear of the projector.
3. Snap cover in place, with the lower guides clamping the rear feet.
4. Tighten rear feet to fix cable cover in place.
MGP D5 21
CEILING MOUNT (option) User Guide
22 MGP D5
User Guide USING THE PROJECTOR
USING THE PROJECTOR
After setting-up, switch on all equipment.
To switch the projector on, firmly press the POWER button on the keypad or the remote control. The STATUS indicator will turn from yellow to green when the unit is switched on.
If the STATUS indicator is flashing yellow, please wait until it turns permanent yellow.
When only one source is connected, the projector will autodetect that source. If more sources are connected, the projector will search for the next active source according to the following list, provided that SOURCE SCAN is set to ON in the SET UP sub menu (see description of menu system):
• VGA 1
• VGA 2
• DVI-D
• Component
• S-Video
• Composite Video
Select between the sources by pressing the SOURCE buttons on the keypad or the remote control. Only sources that are active will be displayed.
If no source is active, searching messages will appear on the screen.
If no source is active for a long time, the projector will go in standby mode if DPMS (power save) is set to ON in the SET UP sub menu. The STATUS indicator will turn from green to flashing yellow, then yellow. The projector will be switched back on if at least one source is (re)activated. The power-down function can be disabled in the menu. See DPMS in the SET UP sub menu.
To switch the projector off, firmly press the POWER button on the keypad or the remote control twice (to confirm that you really
MGP D5 23
USING THE PROJECTOR User Guide want to switch off the unit). The STATUS indicator will turn from green to flashing yellow, then yellow when switched off.
You may not switch the unit on while the STATUS indicator is flashing yellow. Please wait until the indicator is permanent yellow.
24 MGP D5
User Guide MENU SYSTEM
MENU SYSTEM
The menu system gives access to a multitude of image and system controls. The menu system is structured through a top menu and several sub menus. The sub menus may vary depending on the actual source selected. Also, some functions are not available when the DICOM display curve is selected.
When accessing the menu system, you will enter at the position you left last time you were using the menu system.
Press the MENU key and navigate using the arrow keys on the keypad or the trackball or the arrow keys on the remote control
TOP MENU
picture
Basic picture controls
dynamic
Allows additional control over the projected image.
advanced
Advanced picture controls
set up
General projector controls
utilities
System controls and information
control
RS232 and LAN configurations picture dynamic advanced setup utilities control
MGP D5 25
MENU SYSTEM User Guide
PICTURE SUB MENU
S-VIDEO/COMPOSITE VIDEO
brightness contrast color tint sharpness aspect
50
50
50
50
3 fill 16:9
YPbPr (progressive)
brightness contrast color hue space sharpness aspect
50
50
50
50
SMPT REC601 REC709
3 fill 16:9
YPbPr (interlaced)
brightness contrast color tint sharpness aspect
50
50
50
50
3 fill 16:9
VGA
brightness contrast sharpness aspect
40
70
3 fill aspect ratio
}
Not available in DICOM mode
26 MGP D5
User Guide MENU SYSTEM
DVI
brightness contrast sharpness aspect
50
50
3
}
Not available in DICOM mode fill aspect ratio
brightness
Adjusts the image brightness. A higher setting will increase the brightness, a lower setting will decrease the brightness of the image.
contrast
Controls the contrast of the image. A higher setting will yield a
'harder' image with larger difference between shades, while a low setting will produce a 'softer' image with less difference between shades.
color
Adjusts the color saturation. A higher setting will produce stronger coloring, while a lower setting will yield paler colors.
tint
Adjusts the NTSC color tint. Applicable to NTSC (American) video standard only. A higher setting will yield a more reddish color scheme, while a lower setting will turn colors more greenish.
hue
Controls the color hue
sharpness
Controls the image sharpness. A higher setting will yield a harder image, with less filtering. In video applications, this may produce more noise in the projected image. A lower setting will soften the image, looking more smeared out, and reducing the overall noise.
MGP D5 27
MENU SYSTEM User Guide
aspect
Selects image format. An image may be displayed in various aspect ratios. This function is used when displaying source formats that differ from the projectors native display format.
space
Defines the color standard used for component video so that the image is displayed with the proper characteristics.
DYNAMIC SUB MENU
FOR ALL INPUTS
white boost gamma eco mode lamp power lamp runtime:
DICOM
10 on computer 2 off
}
Not available in DICOM mode
10
27 hrs off
white boost
Increases the white level of the image for enhanced contrast
gamma
The source image is adapted to characteristics typical to certain applications. This enables an optimized display of images, depending on whether the source is video, computer etc.
eco mode
Reducing lamp power for maximum lamp life and reduced power consumption
lamp power
Allows for continuously adjustable lamp power for easier calibration of multiple-screen set-ups.
28 MGP D5
User Guide MENU SYSTEM
lamp runtime
The total time the lamp has been operating since the projector was produced or the lamp was replaced, if the lamp counter was reset after replacement.
DICOM
Allows to select a DICOM display function, which optimizes the projector to the DICOM standard.
You can select from 4 DICOM display functions:
• Clearbase:
DICOM clearbase color temperature
• Clearbase boost:
DICOM clearbase color temperature with increased white level
• Full white:
DICOM native projector white color temperature
• Full white boost:
DICOM native projector white color temperature with increased white level
ADVANCED SUB MENU
S-VIDEO/COMPOSITE VIDEO
H position
V position
50
50 color temp custom color
6500 7300 9300 custom video format auto video type
NTSC
DVD
PAL SECAM
VCR
MGP D5 29
MENU SYSTEM User Guide
YPbPr (progressive)
H position
V position
50
50
Phase frequency
4
864 color temp custom color
6500 7300 9300 custom
YPbPr (interlaced)
H position
V position
50
50 color temp custom color
6500 7300 9300 custom video format auto video type
NTSC PAL SECAM
DVD VCR
VGA
H position 50
V position phase
50
4 frequency 1688 color temp custom color
6500 7300 9300 custom
-> Always “custom” in DICOM mode
-> Not available in DICOM mode full auto image press
DVI
color temp custom color
6500 7300 9300 custom
-> Always “custom” in DICOM mode
-> Not available in DICOM mode
h position
Shifts the image sideways.
v position
Shifts the image up and down.
30 MGP D5
User Guide MENU SYSTEM
phase
Adjust for stable image. A jittery image may appear with certain
VGA sources. You may also press the AUTO button on the keypad or remote control to optimize.
frequency
Adjust image width. An incorrect setting may produce vertical, unstable bands in the image, and parts of the image may not be displayed on screen. Push the AUTO button to find a correct setting, or manually adjust the frequency until the vertical bands disappear.
color temp
Changes the color temperature. A video signal demands a different color temperature than a computer image. A higher setting yields a colder (bluer) image, while a lower setting produces a warmer (more yellow) image.
custom color
Defines custom color temperature. Lets you define your own customized color temperature for your specific application.
video format
Select between manual or auto detection of TV standard.
video type
Select between video types; DVD and VCR. The DVD setting is normally used and will yield well defined video images.
custom brightness
Allows for individual user control of red, green and blue brightness.
custom contrast
Allows for individual user control of red, green and blue contrast.
MGP D5 31
MENU SYSTEM User Guide
full auto image
Adjusts h and v position, phase and frequency automatically.
Important:
you must perform the full auto image function on a good test pattern. Otherwise, the image may not be correctly adjusted. Therefore, to perform the full auto image function correctly, run the
calibration
wizard in the
TheaterWatch
software application.
32 MGP D5
User Guide MENU SYSTEM
SET UP SUB MENU
FOR ALL
keystone V keystone H
DPMS source scan orientation
OSD language
RGB Video
0
0 on on off off off
keystone V
Adjust vertical keystone correction. Compensates for the geometrical distortion of the projected image resulting from tilting the projector to shoot higher up on the wall.
keystone H
Adjust horizontal keystone correction. Compensates for the geometrical distortion of the projected image resulting from shooting the image at an angle sideways on the screen.
DPMS
Activate/deactivate DPMS (Display Power Management
Signalling). When DPMS is on, the projector will switch off following the powering off or disconnection of the signal source.
The projector will switch back on when the signal source is reactivated.
source scan
Switches source scan on and off. With source scan on, the projector will search for another source if the current source is disconnected or switched off. With source scan off, the projector will remain at the selected source input even if the source is switched off or disconnected.
MGP D5 33
MENU SYSTEM User Guide
orientation
Select between desktop front, desktop rear, ceiling front and ceiling rear mode. The image will be flipped and reversed accordingly.
OSD
Select where to have the On Screen Display
language
Select between languages
RGB video
Selects RGB video on the component video input (YPbPr).
Requires composite sync connected to the composite video input.
UTILITIES SUB MENU
FOR ALL
system information
OSD
OSD timeout on
50 press off seconds
OSD background opaque translucent reset lamp reset press press service menu test image hide press show
34 MGP D5
User Guide MENU SYSTEM
SYSTEM INFORMATION system information
source: format: mode: software: s-video
576p PAL
69
0034-01.06
lamp remaining: 1999:44 black level: 0
White boost:
MAC:
IP address: subnet: gateway:
TCP port:
UDP port:
0.0.0.0
0
0 brightness: contrast: color: sharpness: gamma: color temp:
0
00-00-00-00-00-00
0.0.0.0
0.0.0.0
50
47
40
3 film 1
6500K
information
Displays information about the source and projector status
OSD
Turn the On Screen Display on (display) or off (hide) during source scan.
OSD timeout
Defines how long OSD is displayed after last key action before it disappears from the screen.
OSD background
Select background mode, whether transparent or opaque.
reset
Resets the projector to its basic settings. All parameters available in the various menus are reset to their factory values.
lamp reset
Reset lamp after lamp change. Do not reset lamp counter unless the lamp has been replaced with an original new lamp.
MGP D5 35
MENU SYSTEM User Guide
service menu
For service personnel only. A special service code is needed to access internal calibration controls and status information. Not accessible to the user.
test image
Applies a fixed test image for set-up purposes
CONTROL SUB MENU
FOR ALL
mode
232
RS232 Address
232
RS232 Fixed
232
baudrate auto
RS232 fixed
1
19200
Mode
Selects between RS232, RIMI (internal) and LAN control modes.
The projector can be controlled by only one of the modes at a time.
RS232 address
For use when daisy-chaining several units. Select auto or fixed address. Only one address scheme is allowed per daisy-chain.
The auto address is allocated following the relative position in the daisy-chain. The fixed address is an absolute address. Only unique fixed addresses are allowed.
RS232 fixed
Select a unique fixed address in the range available.
baudrate
Selects between baudrates 4800, 9600 and 19200. A lower baudrate may be required in installations with long cable runs.
36 MGP D5
User Guide MOUSE CONTROL
MOUSE CONTROL
You may control the computer mouse functions using the remote control.
In order to enable this function, connect a USB cable between the computer and the projector. Ensure that the PC has an operating system that supports USB (Windows™ 98 2nd edition or newer).
As long as the menu system on the projector is not activated, the tracker ball on the remote control will now emulate the mouse movements. When the menu system is activated, the tracker ball is used for menu navigation. (See menu system chapter).
Point the remote control directly at the IR receiver in the front or in the rear. Move the mouse pointer by rolling the tracker ball in the direction required. The LEFT key emulates the left mouse key, while the RIGHT key emulates the right mouse key.
The pointer movement may not be as smooth as you are used to with you ordinary mouse, due to the reduced bandwidth of the infrared remote control connection.
MGP D5 37
RS 232 AND LAN CONTROL User Guide
RS 232 AND LAN CONTROL
RS 232
You may control and monitor the projector remotely through the serial RS232 control interface.
The RS232 protocol is a binary protocol where each command is a series of 32 bytes in one packet. The protocol allows for both SET and GET operations. To utilize GET operations the host needs a routine for receiving and interpreting incoming packets. SEToperations are used to force the projector into different modes, like setting brightness and contrast, switching between sources, etc.
A separate document “RS-232 and LAN communication protocol and command set” is available that describes the communications parameters and operational codes in detail.
LAN
The projector can be controlled and monitored using through the
LAN connector as an alternative to RS232.
LAN control is based on the same command set as RS232.
NOTE! THE PROJECTOR IS CONFIGURED WITH A DEFAULT IP ADDRESS.
SEE THE SYSTEM INFORMATION AVAILABLE THROUGH THE MENU
SYSTEM OR REMOTE CONTROL FOR THE ACTUAL IP-ADDRESS.
Detailed descriptions of configuration, use and command set is described in a separate document “RS-232 and LAN communication protocol and command set”.
You may consider using the LAN interface as a means of theftdetection. When the projector is removed, the LAN will be disconnected; this may be detected over the local area network and could be used to trigger an alarm.
38 MGP D5
User Guide TROUBLESHOOTING
TROUBLESHOOTING
NO IMAGE
No connection:
Check if all connections are properly made.
Source off:
Check if the equipment is powered on.
Lamp dead:
The lamp may need replacement. Check the
LAMP TIME in the UTILITIES sub menu.
Source hibernated:
Engage the source to display and active image.
Notebook external screen:
Different notebook PC's use different combinations of keystrokes to enable the external graphics port.
Source scan off:
Check SOURCE SCAN in the SET UP sub menu. If setting is OFF, the projector will not search for the next active source, but will remain with the current source selected.
DARK IMAGE
Old, worn lamp:
The lamp may need replacement. Check the LAMP TIME in the UTILITIES sub menu.
Low BRIGHTNESS and CONTRAST settings:
Press AUTO or use the menu system, PICTURE sub menu for CONTRAST and
BRIGHTNESS adjustment.
FLICKERING IMAGE
Bad lamp:
Replace the lamp. Check the LAMP TIME in the
UTILITIES sub menu.
MGP D5 39
TROUBLESHOOTING User Guide
UNSHARP IMAGE
Keystone correction may have been activated inadvertently: compressing parts of the image that affect the display of fine-line graphics, text and other images of high resolution.
Source resolution is different from projectors native resolution:
The projector will automatically scale and resize the input format to its native resolution. Use a different scaling factor in the PICTURE sub menu, ASPECT. You may also adjust the SHARPNESS.
40 MGP D5
User Guide MAINTENANCE
MAINTENANCE
The projector may from time to time need cleaning. Never open the unit, as this will void any warranties. Refer service and repair to qualified personnel only.
The projector is using a lamp that has a limited life time. Please refer to the LAMP CHANGE section below for further details.
Only the exterior of the unit may be cleaned. Use a damp cloth.
Make sure no liquids enter the inside of the projector
Vacuum clean all the air vents (A) regularly to maintain sufficient air flow.
The projection lens (B) is sensitive to scratches. Use lens cleaning tissue, available at all photographic stores when cleaning the projection lens. Use lens cap when not in use.
MGP D5 41
MAINTENANCE User Guide
HEAVY DUTY AND CONTINOUS USE
The projector contains moving parts (such as cooling fans) that have limited life-expectancies. When the projector has been used for 7 500 hours, and when the unit is applied to mission-critical use, it is recommended that the projector is given preventive maintenance by a qualified service person. This will help ensure long term stable operation.
42 MGP D5
User Guide LAMP CHANGE
LAMP CHANGE
The STATUS lamp on the keypad will turn red when the lamp life expires. In addition, a message will appear on the screen:
“LAMP LIFE TIME HAS EXPIRED! Please change lamp!”
POWER
STATUS
Change the lamp when lifetime expires.
Always replace lamp with the same type and rating.
Always disconnect the power cord and wait until the projector has cooled down (60 minutes) before opening the lamp cover
(B).
Release the screw (A).
Remove the lamp cover (B).
Release the screws on the lamp house (C).
Pull the handle (D).
MGP D5 43
LAMP CHANGE
Remove the lamp house (E).
Replace with a new lamp in reverse order.
Replace the lamp house (E) and tighten the screws (C).
User Guide
44
Fold the handle (D) in place.
MGP D5
User Guide
Replace the lamp cover (B) and tighten the screw (A).
LAMP CHANGE
In the “utilities” sub menu, reset the lamp timer.
system information
OSD
OSD timeout on
50 press off seconds
OSD background opaque translucent reset lamp reset service menu test image hide press press press show
WARNING
Be careful not to touch the protective glass when replacing the lamp house, this may cause the protective glass to overheat and break while in use.
MGP D5 45
SERVICE INFORMATION User Guide
SERVICE INFORMATION
This product contains no user serviceable parts.
If the product fails to function as expected, please first check that all connections are properly made, and that the power cord is properly connected.
Please check that the projector as well as the video and computer sources are all switched on.
Cables and cords may break over time. Try to change cables and cords, in case there is a bad or intermittent connection.
Check if the circuit breaker or fuse of your mains is intact.
In the event of product failure, please contact your reseller. You should prepare a description of the symptoms of failure you experience.
Please also state product number and serial number as printed on the label on the bottom of the projector.
46 MGP D5
User Guide
TECHNICAL DATA
Resolution
Display technology
Display device
Computer Compatibility
Video Compatibility
Aspect Ratio
Bandwidth
Brightness
Contrast
Zoom lens
Lamp
TECHNICAL DATA
1400 x 1050 (native) SXGA+
Single chip DLP™ technology by Texas
Instruments
LVDS DMD™ with DarkChip2™ technology
UXGA, SXGA+, SXGA, XGA, SVGA, VGA
PC, MAC, SGI and other workstations
RGBHV, RGBS, RGsB
HDTV (1080i, 720p, 576i/p, 480i/p)
NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, SECAM.
Faroudja™ de-interlacing with automatic film mode detection (3 : 2 and 2 : 2 pulldown)
4 : 3 (native), 16 : 9 / 5 : 4 (compatible)
Up to 205 MHz on analog RGB
Up to 160 MHz on DVI
Up to 75 MHz on component input
2500 ANSI lumen (typ), 2200 ANSI lumen
(min) @ 250W lamp power*)
2000 ANSI lumen (typ), 1750 ANSI lumen
(min) @ ECO-mode 200W lamp power*)
*) Initial brightness.
2000 : 1 B/W (typ), 1500 : 1 B/W (min) f = 33 - 42
F = 2.75 - 3.1
Zoom factor = x 1.25
throw ratio = 1.70 - 2.2 : 1 (distance : width) throw distance = 1.5 m - 10 m / 5 - 33 ft.
image width = 0.7 m - 5.7 m / 2.3 - 18.8 ft.
offset = 108%
250W UHP™ dimmable to 200W
MGP D5 47
TECHNICAL DATA User Guide
Lamp Life
Noise level
Dimensions
Weight
Inputs
Outputs
Power
Conformance
Temperature operating
Temperature storage
Humidity operating
2000 hrs (typ) to 50% brightness @ 250W
4000 hrs (typ) to 50% brightness @ 200W
28 dB (typ), 32 dB (max) @ 20°C/68°F, sea level
244 x 278 x 88 mm / 9.6" x 10.9" x 3.5", excluding lens
3.4 kg/7.5 lbs
2 VGA 15 pin female HD-DSUB analog
RGBHV
1 DVI-D female digital RGB
1 Component video female 3 x RCA/phono
1 S-video female 4 pin mini-DIN
1 C-video female RCA/phono
2 Audio 3.5 mm female stereo jack
1 RS 232 9 pin female DSUB (control, firmware update)
1 USB-B female (control, firmware update)
1 LAN RJ-45 female (control, firmware update)
1 Remote Control 3.5 mm female stereo jack
1 VGA Monitor 15 pin female HD-DSUB analog RGBHV
1 Audio 3.5 mm female stereo jack
1 RS 232 9 pin male DSUB
90-260 VAC, 50-60 Hz, 350W
CE, FCC A, CSA(C,US)
0-40°C / 32-104°F, 0-1500 m / 0-4950 ft
0-35°C / 32-95°F, 1500-3000 m / 4950-
9900 ft
-20 - 60°C / -4 - 140°F
20-90% RH, non-condensing
48 MGP D5
User Guide TECHNICAL DATA
Humidity storage 10-95% RH, non-condensing
Specifications subject to change without prior notice. All values may vary up to +/- 20%.
MGP D5 49
TECHNICAL DATA User Guide
1
:
1 ed
Fix
1
0 ns om
Zo ns om
Zo
50 MGP D5
User Guide TECHNICAL DATA
G/Y
PHONO/RCA FEMALE
STEM GREEN: G/Y
SHIELD: GND
B/Pb
PHONO/RCA FEMALE
STEM BLUE: B/Pb
SHIELD: GND
R/Pr
PHONO/RCA FEMALE
STEM RED: R/Pr
SHIELD: GND
S-Video
4 PIN MINI DIN
FEMALE
1 GND
2 GND
3 Luma
4 Chroma
Composite Video
PHONO/RCA FEMALE
STEM YELLOW: Composite
SHIELD: GND
MGP D5 51
TECHNICAL DATA User Guide
Computer DVI
DVI-D
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2/4 Shield
4 Not used
5 Not used
6 DDC Clock
7 DDC Data
8 NC
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1/3 Shield
12 Not used
13 Not used
14 +5V Power
Monitor VGA
15 HIGH DENSITY DSUB FEMALE
1 Analog R in
2 Analog G in
3 Analog B in
4 NC
5 AGND
6 Analog R GND in
7 Analog G GND in
8 Analog B GND in
9 Reserved
10 Sync GND in
11 NC
12 NC
13 H Sync in
14 V Sync in
15 NC
Computer VGA 1
15 HIGH DENSITY DSUB FEMALE
1 Analog R in
2 Analog G in
3 Analog B in
4 AGND
5 AGND
6 Analog R GND in
7 Analog G GND in
8 Analog B GND in
9 Reserved
10 Sync GND in
11 AGND
12 DDC/SDA
13 H Sync in
14 V Sync in
15 DDC/SCL
Computer VGA 2
15 HIGH DENSITY DSUB FEMALE
1 Analog R in
2 Analog G in
3 Analog B in
4 AGND
5 AGND
6 Analog R GND in
7 Analog G GND in
8 Analog B GND in
9 Reserved
10 Sync GND in
11 AGND
12 DDC/SDA
13 H Sync in
14 V Sync in
15 DDC/SCL
52 MGP D5
User Guide
RS-232 in
9 PIN DSUB FEMALE
1 NC
2 RXD
3 TXD
4 NC
5 GND
6 NC
7 NC
8 NC
Audio out
Black
3.5 mm mini jack
TIP: R
STIM: L
RING: GND
Audio in 1
Black
3.5 mm mini jack
TIP: R
STIM: L
RING: GND
USB
DIGITAL USB
1 VCC
2 -Data
3 +Data
4 GND
TECHNICAL DATA
RS-232 out
9 PIN DSUB MALE
1 NC
2 TXD
3 RXD
4 NC
5 GND
6 NC
7 NC
8 NC
RC in
3.5 mm stereo mini jack
TIP: 5V DC
RING: SIGNAL
STEM: GND
Audio in 1
Black
3.5 mm mini jack
TIP: R
STIM: L
RING: GND
LAN
1 TX+
2 TX-
3 RX+
4 GND
5 GND
6 RX-
7 GND
8 GND
MGP D5 53
DECLARATIONS User Guide
DECLARATIONS
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
EN 55022 WARNING
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
CANADA
This Class A digital apparatus complies with Canadian ICES-003.
CCet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
54 MGP D5
advertisement