Roland | User manual | XR-640 Metallic Silver & White Ink Guide

This document describes the characteristics of special color inks (white ink and metallic silver ink) used with SOLJET PRO

4 series printers, important notes, maintenance, and printing method using these inks. For other matters, refer to Setup

Guide and User's Manual of your printer.

When you use metallic silver ink and white ink, be sure to read this first

Thank you very much for purchasing this product.

 To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location.

 Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.

 The contents of this operation manual and the specifications of this product are subject to change without notice.

 The operation manual and the product have been prepared and tested as much as possible. If you find any misprint or error, please inform us.

 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product, regardless of any failure to perform on the part of this product.

 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any article made using this product.

Copyright and property of this Software and this manual belong to Roland DG Corp. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any from or by any means, electronic, mechanical, photocopy, recording or otherwise, without the prior written permission of the publisher.

VersaWorks is a registered trademark of Roland DG Corp.

Windows is a registered trademarks or trademarks of Microsoft® Corporation in the United States and/or other countries.

Pentium are registered trademarks of Intel Corporation in the United States.

Macintosh is a registered trademark of Apple Inc.

Adobe, the Adobe logo, PostScript, PostScript 3, and Illustrator are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. ©2007 Adobe Systems

Incorporated. All rights reserved.

PANTONE® Colors displayed in the software application or in the user documentation may not match

PANTONE-identified standards. Consult current PANTONE Color Publications for accurate color. PAN-

TONE® and other Pantone trademarks are the property of Pantone LLC. © Pantone LLC, 2012.

Pantone is the copyright owner of color data and/or software which are licensed to Roland DG Corp. to distribute for use only in combination with Roland VersaWorks. PANTONE Color Data and/or Software shall not be copied onto another disk or into memory unless as part of the execution of Roland VersaWorks.

Other company names and product names are trademarks or registered trademarks of their respective holders.

Contents

Contents ........................................................................................................1

Chapter 1 Getting Started ...................................................................................3

1-1 What This Document Assumes and Related Manuals ............................4

What This Document Assumes .................................................................................................... 4

Related Manuals ............................................................................................................................... 4

VersaWorks Online ........................................................................................................................... 4

1-2 Before Starting Operations .....................................................................5

Important: Characteristics of Inks and Important Notes.................................................... 5

Before Starting the Day's Work .................................................................................................... 5

1-3 Important Notes on Printing ....................................................................6

Using the Middle Pinch Rollers in Printing and Cutting ..................................................... 6

When Performing Pullback Printing .......................................................................................... 6

Important Notes on Using Media Take-up System .............................................................. 6

Important Notes in Using Transparent Media ........................................................................ 7

Precautions When Using an Optional Dryer ........................................................................... 7

Chapter 2 Getting Ready .....................................................................................9

2-1 Preparing VersaWorks ..........................................................................10

Starting VersaWorks .......................................................................................................................10

Creating a Folder for Saving PS Files .......................................................................................10

2-2 Printer Preparations ..............................................................................11

Making the Printer Settings and Loading Media ................................................................11

2-3 Creating Printing Data ...........................................................................12

Basic Approach for Creating Printing Data ...........................................................................12

Creating Data for Printing ...........................................................................................................12

Blend Print and Layered Print (Metallic Silver and CMYKLcLmLk) ................................18

Chapter 3 Printing ..............................................................................................21

3-1 Print Job Setting : Equipped with White & Silver ..................................22

Printing Only with Metallic Silver Ink ......................................................................................22

Blend Print (Metallic Silver + CMYKLcLm)..............................................................................24

Layered Print (Metallic Silver  CMYKLcLm) ........................................................................26

Layered Print (CMYKLcLm Metallic Silver) .........................................................................28

Printing Only with White Ink ......................................................................................................30

Printing with White and CMYKLcLm Ink ................................................................................32

Printing with While, Metallic Silver, and CMYKLcLm Ink ..................................................35

3-2 Print Job Setting : Equipped with Silver Only ........................................39

Printing Only with Metallic Silver Ink ......................................................................................39

Blend Print (Metallic Silver + CMYKLcLmLk) .........................................................................41

Layered Print (Metallic Silver  CMYKLcLmLk) ...................................................................43

Layered Print (CMYKLcLmLk Metallic Silver) ....................................................................45

3-3 Print Job Setting : Equipped with White Only .......................................48

Printing Only with White Ink ......................................................................................................48

Printing with White and CMYKLcLmLk Ink ............................................................................50

3-4 Starting the Print Operation ..................................................................53

Starting the Print Operation .......................................................................................................53

Printing a Metallic Color Chart...................................................................................................54

1

Contents

Chapter 4 Advanced ..........................................................................................57

4-1 Pullback printing: Equipped with White & Silver ...................................58

Pullback printing (White  Metallic silver/CMYKLcLm) ...................................................58

Pullback printing (Metallic silver/CMYKLcLm  White) ...................................................64

4-2 Performing Texture Printing: Equipped with Silver ................................70

What is Texture Printing? .............................................................................................................70

Create The Texture Printing Data ..............................................................................................70

Performing Texture Printing .......................................................................................................73

Printing a Texture Chart ...............................................................................................................73

4-3 Maintenance .........................................................................................75

When Dot Drop-out Etc. Cannot be Corrected ....................................................................75

2

Copyright © 2012 Roland DG Corporation http://www.rolanddg.com/

Chapter 1

Getting Started

1-1 What This Document Assumes and Related Manuals .............4

What This Document Assumes ...................................................4

Related Manuals ..........................................................................4

VersaWorks Online ......................................................................4

1-2 Before Starting Operations ......................................................5

Important: Characteristics of Inks and Important Notes ..............5

Before Starting the Day's Work ...................................................5

1-3 Important Notes on Printing .....................................................6

Using the Middle Pinch Rollers in Printing and Cutting ...............6

When Performing Pullback Printing .............................................6

Important Notes on Using Media Take-up System ......................6

Important Notes in Using Transparent Media ..............................7

Precautions When Using an Optional Dryer ................................7

3

1-1 What This Document Assumes and Related Manuals

What This Document Assumes

Before performing any operations described in this guide, make sure that all the following preparations have been complete.

 Hardware setup, such as the assembly and installation of SOL JET PRO4 series printer (hereinafter, the printer)

 Installing VersaWorks on your computer, and connecting the computer to the printer via a network.

Related Manuals

Read the following documentation for information about setting up this machine and VersaWorks.

Setup Guide

This manual describes details about how to make the printer ready for use and where it should be installed. Be sure to read this manual.

User's Manual

This manual describes operation methods in detail. After you've read the

Setup Guide, be sure to read this manual.

Roland VersaWorks

Quick Start Guide

Chapter 1 of this manual, “Setting for VersaWorks,” provides you with instructions necessary to perform printing with VersaWorks, including how to install the software. Be sure to read this chapter following the above

User's Manual.

You are also recommended to read Chapter 2, “Getting Started,” to become familiar with how to use this program.

VersaWorks Online

This document describes the important notes to use the metallic silver ink and the white ink as well as the basic printing method using these inks. You can get the latest information about Roland VersaWorks and the information on printing methods requiring more complex settings by viewing VersaWorks Online. If you want to learn more about the features of Roland VersaWorks, or if you want to use metallic silver ink and the white ink more effectively, be sure to visit VersaWorks Online.

URL : http://dg4.roland.co.jp/en/RVW2forWeb/index.html

VersaWorks Online can be displayed by clicking [Help] - [VersaWorks Online] from the main menu.

4

Chapter 1 Getting Started Chapter 1 Getting Started

Chapter 1 Getting Started

1-2 Before Starting Operations

*If equipped with both Metallic Silver ink and White ink, Lk (Light Black) ink is not used. Ignore

"Lk" in this manual.

Important: Characteristics of Inks and Important Notes

The usage and handling of white ink and metallic silver ink involve some important considerations that do not apply to ink of other colors. Be sure to familiarize yourself with the characteristics of the inks before you use them.

White ink and metallic silver ink precipitate.

If they are allowed to stand, the precipitates in them may solidify and cause clogging of the print heads or other malfunction. Be sure to observe the cautions in this manual.

Maintenance must be performed.

 Always keep the main power switched on. If the main power is switched off, the automatic maintenance function stops working, and it may result in malfunction.

 We recommend that you operate the printer at least once a week.

 If the printer is left unused for a long period of time, ink precipitation may occur, causing unstable ink discharge, which may result in dot drop-out, etc. In such cases, the precipitated and solidified ink needs to be cleared.

 P. 75, "When Dot Drop-out Etc. Cannot be Corrected"

Drying inks

 After output, allow the ink to dry sufficiently. Note that white ink and metallic silver ink in particular require printing at a high density, and so are more difficult to dry than CMYKLcLMLk inks.

 Use an auxiliary drying unit (DU series).

 P. 7, "Precautions When Using an Optional Dryer"

We strongly recommend lamination.

Depending on conditions, the weatherability of metallic silver ink and white ink may be inferior to that of

CMYKLcLmLk inks. Therefore, laminating is strongly recommended.

Before Starting the Day's Work

 Remove just the white and metallic silver ink cartridges, shake them gently, then reinsert them.

 You do not have to shake the cyan, magenta, yellow, black, light cyan, light magenta, light black ink cartridges every day, but be sure to shake them when you install new cartridges for these colors.

The ingredients in white and metallic silver inks tend to settle. Each day, before starting the day's operations, be sure to carry out the above steps. Allowing the ink to stand without carrying out these steps can cause the settled material to harden, resulting in malfunction or other problems.


5

1-3 Important Notes on Printing



Using the Middle Pinch Rollers in Printing and Cutting

Since metallic silver ink and white ink are difficult to dry, the middle pinch rollers will smudge the printed surface when printing and cutting are performed. Thus, when you perform printing and cutting using metallic silver ink and/or white ink, secure the media in place using only two pinch rollers on the right and the left.

However, some types of the media may partially float and it may cause bad effect on printing, feeding and/ or cutting. Use the media after confirmation of the nature of your media.

When Performing Pullback Printing

What is Pullback Printing?

Pullback printing refers to a printing method in which the white-ink (or metallic silver ink) undercoat is printed first, and then CMYKLcLmLk color is printed on top of white ink (or vice versa); in the process, the already printed media is pulled back to the original position once, and then overprinting is performed.

Allow the ink to dry thoroughly.

 Dry the ink sufficiently before you perform pullback printing with the next color. Performing pullback printing before the ink has dried enough may make attractive printing impossible or cause problems such as reduced weatherability.

 Drying time differs according to various conditions, but as a general guide you should use an auxiliary drying unit (DU sereies) and also allow the media to stand for an additional 15 minutes.

 In particular, when you're pullback printing a white or metallic silver undercoat with CMYKLcLmLk inks, allow the undercoat to dry thoroughly before you overprint it. If the undercoat is not dry enough, differences in dryness may cause variations in the overprinted CMYKLcLmLk colors.

Using the middle pinch rollers

The middle pinch rollers may smudge the printed surface when the media is pulled back. When you perform pullback printing, we recommend securing the media in place using only two pinch rollers (one on the left and one on the right).

Select "TU2" When Using the Media Take-up System

When the media take-up system is used for pullback print, select "TU2" in "SETUP SHEET." For more information, refer to "Using Media Take-up System" of the User's Manual.

Important Notes on Using Media Take-up System

Since metallic silver ink and white ink are difficult to dry, if you use the media take-up system (at your option), media and/or the printed surface may be smudged depending on the type of media you use. If you use the media take-up system leaving the middle pinch rollers removed, some types of the media may not be taken up normally and/or cause bad effect on printing, feeding and/or cutting quality as well as partial float of the media. Be sure to use the media take-up system on confirmation of the nature and compatibility of your media.

6

Chapter 1 Getting Started Chapter 1 Getting Started


1-3 Important Notes on Printing

Important Notes in Using Transparent Media

Loading Transparent Media

 Set the [EDGE DETECTION] menu item to "DISABLE". Transparent media cannot be loaded unless this setting is made.

 Ensure a margin of at least 75 mm from the leading edge of the media to the printing- or cutting-start location.

Important Notes On The Amount Of Media Remaining

 When you use transparent media, the presence of media cannot be detected. In such cases, printing operation does not stop when the media runs out, and there is a chance that the platen or the like may become soiled with ink or that ink may get inside and damage the machine.

 If media runs out while printing is in progress, immediately press to stop printing.

Using The Middle Pinch Rollers

The middle pinch rollers scratch media slightly, and on transparent media such scratches can be very noticeable. Also, the middle pinch rollers will smudge the printed surface when transparent media is pulled back after printing. When you use transparent media, secure the media in place using only two pinch rollers on the right and the left.

Automatic crop-mark detection

Automatic crop-mark detection may not be possible for some media, such as transparent media. In such cases, perform alignment manually.

Precautions When Using an Optional Dryer

Use an optional dryer (DU series) we recommend.

Contact your authorized Roland DG Corp. dealer for recommended dryer models.

Select “ENABLE” in the [OPTION DRYER] menu.

This setting is required to operate the printer together with an optional dryer (DU series).


7

8

Chapter 2

Getting Ready

2-1 Preparing VersaWorks ...........................................................10

Starting VersaWorks ..................................................................10

Creating a Folder for Saving PS Files .......................................10

2-2 Printer Preparations ...............................................................11

Making the Printer Settings and Loading Media ........................11

2-3 Creating Printing Data ...........................................................12

Basic Approach for Creating Printing Data ................................12

Creating Data for Printing ..........................................................12

Blend Print and Layered Print (Metallic Silver and

CMYKLcLmLk) ..........................................................................18

9

2-1 Preparing VersaWorks

Starting VersaWorks

On the computer you are using, start VersaWorks. For information on how to start the program, see the Roland

VersaWorks Quick Start Guide. After starting the program, go to the upper left of the main screen and check to make sure that "Model (or Nickname) of Your Printer" is displayed, and that "Status" is set to "Ready to Print."

Creating a Folder for Saving PS Files

Before you actually print an image you draw using application software such as Adobe Illustrator, it is necessary to save the image as a PS file(s). And then, you can print the image by loading the PS file(s) on VersaWorks.

Because of this, you should create a folder for saving PS files in advance. It is recommended to locate the folder in the root directory on your computer's local disk.

Procedure

 Open [Computer] ( or [My Computer]), and then open [Local Disk (C:)].

 Create a new folder.

Click [File] , [Create New], and then [Folder], or click

"New Folder" from the menu.

 Name the created new folder.

Here you name the folder "MT_print", for example.

10

Chapter 2 Getting Ready Chapter 2 Getting Ready

Chapter 2 Getting Ready

2-2 Printer Preparations

Making the Printer Settings and Loading Media

When Using Transparent Media

When you're using transparent media, make the necessary printing settings on the printer and load the media accordingly.

Procedure

 In the menu of the printer, set [EDGE DETECTION] to "DISABLE."

 Load media (transparent media or transparent media with adhesive) into the printer.

 When the media warps or partially floats, ensure a margin of about 200 mm from the leading edge of the media to the printing- or cutting-start location.

 Be sure to use the media clamps when you load media.

When Using Media Other Than Transparent Media

Load the media using the method described in the User's Manual of your printer.


11

2-3 Creating Printing Data

Basic Approach for Creating Printing Data

When Using Metallic Silver Ink

You can create the printing data according to the two methods below.

 Specify the spot color so as to use only the metallic silver ink.

Apply the spot color named "RDG_MetallicSilver" to the areas you want to print using the metallic silver ink.

 Use the exclusive metallic color special colors library.

From the exclusive metallic color special colors library, select the metallic color to be used which is the combination color of CMYK LcLmLk ink and metallic silver ink.

When Using White Ink

Specify the spot color named "RDG_WHITE" to the areas you want to print using the white ink.

Creating Data for Printing

Create the data for printing using the metallic silver ink or the white ink.

The program used to create the printing data is Adobe Illustrator CS6, in this section. For detailed information on drawing methods and how to work with palettes, refer to the documentation or online help for Adobe

Illustrator CS6. If you are using another version of Adobe Illustrator, operations may be somewhat different from those explained here.

1.

Open the exclusive swatch library.

 At the swatch palette menu, select [Open Swatch Library], then [Other Libraries].

The "Open" window appears.

The swatch palette is displayed by going to the menu, selecting [Window], and then selecting [Swatch].

12




 Open folders in the order of [Computer] (or [My Computer]) → [OS (C:) ( or [Local

Disk (C:)]) ] → [Program Files] → [Roland VersaWorks] → [Swatch] → [Illustrator], then select "Roland VersaWorks.ai"

Depending on the settings of your computer, the extension ".ai" might not be shown.

Click [Open].

The swatch library containing "RDG_MetallicSilver" and "RDG_WHITE" is displayed.

 Open the same folders as in step



, and then select "Roland Metallic Color System

Library.ai."


Click [Open].

The swatch library is displayed which is containing the "metallic color" created by mixing the metallic silver ink and CMYKLcLmLk ink.

By saving the ".ai" file selected in steps

 and

 into the folder below, you can register each swatch library to the Adobe Illustrator's library. Once the registration is performed, you can open the library directly from the swatch palette menu, eliminating the need to search the file every time you start Adobe Illustrator.

C:\Program Files\Adobe\Adobe Illustrator CS6\Presets\(language abbreviation)\Swatches

* "C" is the name of your computer's local disk.

*The language abbreviation differs depending on the language used.

*Depending on the Illustrator used, "\Preset\Swatch" may be used instead of "\Presets\(language abbreviation)\Swatch" is "\Preset\Swatch."


13


2.

Create the illustration, and specify the spot color that matches the color you want to print.

 Create the illustration.

Be sure to draw the illustration in the CMYK mode.

 Specify each spot color that matches the color you want to print.

Desired ink or color

Metallic silver ink

White ink

Metallic color

(Metallic silver/CMYKLcLmLk combination color)

Spot color name

RDG_MetallicSilver

RDG_WHITE

RVW-MT-Silver, RVW-MT-Bronze, RVW-

MTTitanBlack,etc.

Specify " RDG_WHITE " for the areas where you want to use white ink.

Specify " RDG_MetallicSilver " for the areas where you want to use metallic silver ink.

From the metallic color special colors library (Roland

Metallic Color System Library), specify the color such as "RVW-MT-Bronze" for the areas where you want to use metallic color

Using the metallic silver ink, you can perform the blend print and the layered print by combining the ink with the CMYKLcLmLk ink.

 P. 18, “Blend Print and Layered Print (Metallic Silver and CMYKLcLmLk)”

14




3.

Create the PS (PostScript) file.

 Select [Print] from the [File] menu.

Select [Roland VW].

When a nickname is set, or when more than one printer is connected, select “Roland VW_(the nickname of the printer used for output).”

Click [Setup].

Click [Continue].


15


 Turn on the [Print to file] option.

Click [Preferences].

Click [Advanced] in the [Layout] tab.

Click the down arrow to the right of the

[Paper Size] box, and then click [PostScript

Custom Page Size] from the list that appears.

For "Custom Page Size Dimensions," enter the values in the "Width" and "Height" fields.

Enter values for the same size as the illustration you created in step

2.

.

16




 Click [OK] three times to close the "PostScript Custom Page Size Definition," "Roland

VersaWorks Advanced Options," and "Printing Preferences" dialog boxes.

The "Print" dialog box returns.

 Click [Print].

Click [Print].



Select the folder you created in "Creating a

Folder for Saving PS Files" on page 10.

Specify the destination and file name for saving.

Example: " C:\MT_print " for the folder to save to, and

" mt.ps " as the file name

Click [Save].

The image is saved as a PS file.

Assign the name you want. It may be a good idea to assign a name that indicates that the file uses white and metallic silver ink.

 Open the folder you saved to and make sure the file has been created.


17


Blend Print and Layered Print (Metallic Silver and CMYKLcLmLk)



The blend print and the layer print are printing methods in which the metallic silver ink is combined with the

CMYKLcLmLk ink. Both methods enable metallic printing which cannot be available only with the CMYKLcLmLk ink. The blend print and the layer print are different from each other in terms of how to print. They are different also in the metallic impression of CMYKLcLmLk. You can select the blend print or layer print in [Mode] of the print setting. You can select either print mode according to your preference.

 P. 26, “Layered Print (Metallic Silver



CMYKLcLm),” p. 41, “Blend Print (Metallic Silver + CMYKLcLmLk),” p.

45, “Layered Print (CMYKLcLmLk



Metallic Silver)”

* When you perform “Printing with White, Metallic Silver, and CMYKLcLm Ink” (page 35), the printing method is limited to the blend print.

In performing the blend print or the layered print, you can specify the colors from the metallic color special colors library. However, if you specify the metallic colors with the same names for the blend print and the layered print, the tones of the colors are different between

them. We recommend that you check the tones of the colors by performing the test printing or printing out the Metallic Color Chart.

Seeing the metallic color chart for the layered print, you may feel a slight inconsistency between the names and the tones of the colors. This is because the colors listed in the Metallic Color

Chart are named based on those for the blend print.

 P. 54, “Printing a Metallic Color Chart ”

Blend Print

(Image of printing method)

The metallic silver ink and the CMYKLcLmLk ink are blended to be a single layer for printing.

Media

Metallic Silver and CMYKLcLmLk

18




Layered Print


The metallic silver ink and the CMYKLcLmLk ink are separated into the different layers and printed in that order. (Metallic silver ink  CMYKLcLmLk ink)

The printed image is to be seen from this side

(the printed surface of the finished results).

Media

CMYKLcLmLk

Metallic Silver

The metallic silver ink and the CMYKLcLmLk ink are separated into the different layers and printed in that order. (CMYKLcLmLk ink  Metallic silver ink)

Media

Metallic Silver

The printed image is to be seen from this side (the opposite side of the printed surface of the finished results).

CMYKLcLmLk


19

20

Chapter 3

Printing

3-1 Print Job Setting : Equipped with White & Silver ...................22

Printing Only with Metallic Silver Ink ..........................................22

Blend Print (Metallic Silver + CMYKLcLm) ................................24

Layered Print (Metallic Silver  CMYKLcLm) ...........................26

Layered Print (CMYKLcLm Metallic Silver) ............................28

Printing Only with White Ink .......................................................30

Printing with White and CMYKLcLm Ink ....................................32

Printing with While, Metallic Silver, and CMYKLcLm Ink ...........35

3-2 Print Job Setting : Equipped with Silver Only ........................39

Printing Only with Metallic Silver Ink ..........................................39

Blend Print (Metallic Silver + CMYKLcLmLk) ............................41

Layered Print (Metallic Silver  CMYKLcLmLk) .......................43

Layered Print (CMYKLcLmLk Metallic Silver) ........................45

3-3 Print Job Setting : Equipped with White Only ........................48

Printing Only with White Ink .......................................................48

Printing with White and CMYKLcLmLk Ink ................................50

3-4 Starting the Print Operation ...................................................53

Starting the Print Operation .......................................................53

Printing a Metallic Color Chart ...................................................54

21

3-1 Print Job Setting : Equipped with White & Silver

Printing Only with Metallic Silver Ink

This section describes how to perform printing only with the metallic silver ink. To use the metallic silver ink in printing, you need to use the printing data where the use of the metallic silver ink is designated. If the printing data have the portion designating the use of other colors, with the settings described in this section, you can print with the metallic silver ink only the area of the image which has been designated to print with the metallic silver ink.

 P. 12, “2-3 Creating Printing Data”

Procedure

 Make sure that you have finished making the preparations for VersaWorks, getting the

printer ready, and creating the printing data ( page 9, "Chapter 2 -- Getting Ready").

 Double-click .

"Queue A Properties" window appears.





Click .

For [Media Type], select names with [MT] attached such as "Generic Vinyl 1 [MT]".

Make the selection that matches the media to be used. Selecting an item attached with [MT] enables you to choose the print mode that can use the metallic silver ink.

For [Print Quality], select either [High

Quality] or [Standard].

For [Mode], select [MetallicSilver (v)].

22

Chapter 3 Printing Chapter 3 Printing

Chapter 3 Printing


Click .



Turn on the [Convert Spot Color] option.

Click .



In [Operation Mode], select the operation of the printer.

 Click [OK] to close the "Queue A Properties" window.

This is the end of the print job setting. To start printing, go on to page 53 “Starting the Print Operation.”

* Only the settings necessary for the use of the metallic silver ink are described in this section. For other settings, refer to the online help provided for VersaWorks.

* If you select [CMYKLcLm (v)] for [Mode] in the procedure



, only the area of the image where CMYKLcLm is specified in the printing data is to be printed.


23


Blend Print (Metallic Silver + CMYKLcLm)

This section describes how to perform the blend print with the metallic silver ink and CMYKLcLm ink.


To perform the blend print, you need to use the printing data where the use of the metallic silver ink and the

CMYKLcLm ink is designated.



The metallic silver ink and the CMYKLcLm ink are blended to be a single layer for printing.

Media

Metallic Silver and CMYKLcLm

Procedure





24








Click .





For [Mode], select [CMYKLcLmMt(v)].

 Click .






Click .


Click [OK] to close the "Queue A Properties" window.




25


Layered Print (Metallic Silver  CMYKLcLm)

This section describes how to perform the layered print with the metallic silver ink and CMYKLcLm ink using the metallic silver ink as background.

 P. 18, “ Blend Print and Layered Print (Metallic Silver and CMYKLcLmLk )”

To perform the layered print, you need to use the printing data where the use of the metallic silver ink and the CMYKLcLm ink is designated.



The metallic silver ink and the CMYKLcLm ink are separated into the differ-

ent layers and printed in that order. (Metallic silver ink  CMYKLcLm ink)

The printed image is to be seen from this side (the printed surface of the finished results).

Media

Metallic Silver

CMYKLcLm

Procedure





26










Click .




Quality (Layered)] or [Standard (Layered)].

If [Mode] is selectable, select [Mt ->

CMYKLcLm (v)].

Click .


 Click .








27


Layered Print (CMYKLcLm Metallic Silver)

This section describes how to perform the layered print with the metallic silver ink and CMYKLcLm ink using the CMYKLcLm ink as background.


To perform the layered print, you need to use the printing data where the use of the metallic silver ink and the CMYKLcLm ink is designated.



The metallic silver ink and the CMYKLcLm ink are separated into the differ-

ent layers and printed in that order. (CMYKLcLm ink  Metallic silver ink)

Media


Metallic Silver

CMYKLcLm

Procedure





28












Click .

For [Media Type], select either "Generic

Clear Film [MT]" or "xxx [MT] : PET Clear

Film, Adhesive".

* “xxx” indicates “SP-CLT” and others.



For [Mode], select [CMYKLcLm (v)-> Mt].

Click .


Click .



29


When You Want to Display the Side Opposite the Printed Surface by Using Clear Film.

Click .

Turn on the [Mirror] option.

When the printing data with mirror image is prepared beforehand, you do not need to turn on this option.




Printing Only with White Ink

This section describes how to perform printing only with the white ink. To use the while ink in printing, you need to use the printing data where the use of the white ink is designated. If the printing data have the portion designating the use of other colors, with the setting described in this section, you can print with the white ink only the area of the image which has been designated to print with the white ink.


Procedure



30












Double-click .


Click .

In [Media Type], select one from "Generic

Clear Film," "Generic Clear Film [MT]," "xxx

: PET Clear Film, Adhesive," and "xxx [MT]:

PET Clean Film, Adhesive."




For [Mode], select [White (v)].

Click .



31


 Click .






* Only the settings necessary for the use of the white ink are described in this section. For other settings, refer to the online help provided for VersaWorks.

Printing with White and CMYKLcLm Ink

This section describes how to perform printing with the white ink and the CMYKLcLm ink. Deciding which ink between the white and the CMYKLcLm you want to use for the base is an important point in determining the print job setting here. To use the white ink for printing, you need to use the printing data where the use of the white ink is designated.


Procedure

 Make sure that you have finished making the preparations for VersaWorks, getting the printer ready, and creating the printing data (



page 9, "Chapter 2 -- Getting Ready").



32






Click .


Clear Film" or "xxx :PET Clear Film, Adhesive."


 For [Print Quality], select either [High


With [Mode], select the print mode.

W -> CMYKLcLm (v)

Inks are overprinted in the sequence of white and then CMYKLcLm Color.

CMYKLcLm -> W (v)

Inks are overprinted in the sequence of CMYKLcLm and then white Color.

Image of overprinting in the sequence of white and then CMYKLcLm Color

(Print Mode "W -> CMYKLcLm (v) ")

Transparent film


White

CMYKLcLm

* The white data and the CMYKLcLm color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.


33


Image of overprinting in the sequence of CMYKLcLm Color and then white

(Print Mode "CMYKLcLm -> W (v) ")

Transparent film

White

CMYKLcLm




* The white data and the CMYKLcLm color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.

Click .


 Click .


When You Want to Display the Side Opposite the Printed Surface by Using Clear

Film.  P. 30

34




 Click [OK] to close the “Queue A Properties” window.



Printing with While, Metallic Silver, and CMYKLcLm Ink

This section describes how to perform printing with the metallic silver ink, the white ink, and the CMYKLcLm ink. Deciding which ink between the white and the others (the metallic silver and CMYKLcLm) you want to use for the base is an important point in determining the print job setting here.

To use the metallic silver ink and the white ink, you need to use the printing data where the use of the respective inks is designated. For the area of the image to be printed with the metallic silver ink and the CMYKLcLm ink combined, the setting is fixed to the blend print.


Procedure





 Click .


Clear Film [MT]" or "xxx [MT] :PET Clear

Film, Adhesive".



35


 For [Print Quality], select either [High



W -> CMYKLcLmMt(v)

Inks are overprinted in the sequence of white and then metallic silver/CMYKLcLm Color.

CMYKLcLmMt -> W(v)

Inks are overprinted in the sequence of metallic silver/CMYKLcLm Color and then white.

Image of overprinting in the sequence of white and then metallic silver/CMYKLcLm Color

(Print Mode "W -> CMYKLcLmMt (v) ")

Transparent film


White

Metallic silver/CMYKLcLm

* The white data and the metallic silver/CMYKLcLm color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.

36




Image of overprinting in the sequence of metallic silver/CMYKLcLm Color and then whit

(Print Mode "CMYKLcLmMt -> W (v) ")

Transparent film

White


Metallic silver/CMYKLcLm



* The white data and the metallic silver/CMYKLcLm color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.

Click .




Click .



Film.



P. 30


37




* Only the settings necessary for the use of the metallic silver ink and white ink are described in this section.

For other settings, refer to the online help provided for VersaWorks.

38


3-2 Print Job Setting : Equipped with Silver Only

Printing Only with Metallic Silver Ink

This section describes how to perform printing only with the metallic silver ink. To use the metallic silver ink in printing, you need to use the printing data where the use of the metallic silver ink is designated. If the printing data have the portion designating the use of other colors, with the settings described in this section, you can print with the metallic silver ink only the area of the image which has been designated to print with the metallic silver ink.


Procedure









Click .





For [Mode], select [MetallicSilver (v)].


39


 Click .


 Click .





* If you select [CMYKLcLmLk (v)] for [Mode] in the procedure



, only the area of the image where CMYKLcLmLk is specified in the printing data is to be printed.

40




Blend Print (Metallic Silver + CMYKLcLmLk)

This section describes how to perform the blend print with the metallic silver ink and CMYKLcLmLk ink.


To perform the blend print, you need to use the printing data where the use of the metallic silver ink and the

CMYKLcLmLk ink is designated.



The metallic silver ink and the CMYKLcLmLk ink are blended to be a single layer for printing.

Media

Metallic Silver and CMYKLcLmLk

Procedure






41






Click .





For [Mode], select [CMYKLcLmLkMt(v)].

 Click .


 Click .







42




Layered Print (Metallic Silver  CMYKLcLmLk)

This section describes how to perform the layered print with the metallic silver ink and CMYKLcLmLk ink using the metallic silver ink as background.

 P. 18, “ Blend Print and Layered Print (Metallic Silver and CMYKLcLmLk ”

To perform the layered print, you need to use the printing data where the use of the metallic silver ink and the CMYKLcLmLk ink is designated.



The metallic silver ink and the CMYKLcLmLk ink are separated into the differ-

ent layers and printed in that order. (Metallic silver ink  CMYKLcLmLk ink)


Media

Metallic Silver

CMYKLcLmLk

Procedure






43








Click .


Make the selection that matches the media to be used.

Selecting an item attached with [MT] enables you to choose the print mode that can use the metallic silver ink.



If [Mode] is selectable, select [Mt ->

CMYKLcLmLk (v)].

Click .


Click .







44




Layered Print (CMYKLcLmLk Metallic Silver)

This section describes how to perform the layered print with the metallic silver ink and CMYKLcLmLk ink using the CMYKLcLmLk ink as background.


To perform the layered print, you need to use the printing data where the use of the metallic silver ink and the CMYKLcLmLk ink is designated.



The metallic silver ink and the CMYKLcLmLk ink are separated into the different layers

and printed in that order. (CMYKLcLmLk ink  Metallic silver ink)

Media


Metallic Silver

CMYKLcLmLk

Procedure






45


 Click .

For [Media Type], select "xxx :PET Clear

Film, Adhesive [MT]".










For [Mode], select [CMYKLcLmLk (v)->

Mt].

Click .


Click .


46




When You Want to Display the Side Opposite the Printed Surface by Using Clear Film.

Click .

Turn on the [Mirror] option.

When the printing data with mirror image is prepared beforehand, you do not need to turn on this option.





47

3-3 Print Job Setting : Equipped with White Only

Printing Only with White Ink

This section describes how to perform printing only with the white ink. To use the while ink in printing, you need to use the printing data where the use of the white ink is designated. If the printing data have the portion designating the use of other colors, with the setting described in this section, you can print with the white ink only the area of the image which has been designated to print with the white ink.


Procedure









Click .


Clear Film" or "xxx :PET Clear Film, Adhesive".




For [Mode], select [White (v)].

48






Click .


 Click .






49


Printing with White and CMYKLcLmLk Ink

This section describes how to perform printing with the white ink and the CMYKLcLmLk ink. Deciding which ink between the white and the CMYKLcLmLk you want to use for the base is an important point in determining the print job setting here. To use the white ink for printing, you need to use the printing data where the use of the white ink is designated.


Procedure

 Make sure that you have finished making the preparations for VersaWorks, getting the printer ready, and creating the printing data (










Click .


Clear Film" or "xxx :PET Clear Film, Adhesive."





W -> CMYKLcLmLk (v)

Inks are overprinted in the sequence of white and then CMYKLcLmLk Color.

CMYKLcLmLk -> W (v)

Inks are overprinted in the sequence of CMYKLcLmLk and then white Color.

50




Image of overprinting in the sequence of white and then CMYKLcLmLk Color

(Print Mode "W -> CMYKLcLmLk (v) ")

Transparent film


White

CMYKLcLmLk

* The white data and the CMYKLcLmLk color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.

Image of overprinting in the sequence of CMYKLcLmLk Color and then white

(Print Mode "CMYKLcLmLk -> W (v) ")

Transparent film

White

CMYKLcLmLk


* The white data and the CMYKLcLmLk color data are actually printed simultaneously, but they are shown here as separate layers in order to indicate the printing sequence.


51


 Click .




Click .



Film.  P. 30




52



3-4 Starting the Print Operation

Starting the Print Operation

Following the print job setting, you can start the print operation.

Procedure

 Make settings for the print job.

 P. 22, “3-1 Print Job Setting : Equipped with White & Silver,” p. 39, “3-2 Print Job Setting : Equipped with Silver Only,” p. 48, “3-3 Print Job Setting : Equipped with White Only”

 Go to “Job List,” click the “Queue A” tab, and drag the printing data to the queue A job list (If the print job setting has been made in

[Queue B], drag and drop the printing data on the job list of [Queue B].).

The contents of the data are displayed in the preview window, and the layout on the media is displayed in the layout window.

Areas using “RDG_MetallicSilver” or special metallic color (RVW-MTBronze, etc.) are displayed with shading in transparent gray.

Areas using “RDG_WHITE” is displayed with shading in transparent magenta.


53


 Select the print job in the job list, and then click .

Printing will be started.

After printing, allow the ink to dry sufficiently.

We strongly recommend performing lamination.

To continue printing similar data, repeat steps

 and



. Also, if you want to modify detailed settings for each job, it will be convenient to perform modifications in the “Job Setting” window

(which you can display by double-clicking the print job in the job list).

Printing a Metallic Color Chart

The Metallic Color Chart is the printing sample of the special metallic color. By printing the Metallic Color Chart, you can confirm the “complete metallic color chart” representing the special metallic color itself that can be printed with “Your Printer” and “Your Media” (slight pattern differences is possible to occur depending on the conditions of the printer and media.) By selecting colors from this color chart and creating illustrations with these colors, you can accurately reproduce the desired colors.

Procedure

 Make sure that you have finished making the preparations for VersaWorks, and getting the printer ready (






54






Click , configure the settings in [Quality Settings] and [Color Management].

 P. 22, “3-1 Print Job Setting : Equipped with White & Silver,” p. 39, “3-2 Print Job Setting : Equipped with Silver Only”

Click [OK].



When printing a Metallic Color Chart, the [Quality] settings from the [Queue Properties] window are always applied. Since you cannot change the quality settings for the job using the

[Job Settings] window after it has been added, be sure to configure the settings in the [Queue

Properties] window before performing the following operations.

Click [Media] and then [Metallic Color

Chart].



Check the page size.

If the size of the media loaded on the printer is not adequate for the page size, change it to another media of sufficient size.

Click [OK].

The print job of the Metallic Color Chart is added to the job list.

Click .



55

56

Chapter 4

Advanced

4-1 Pullback printing: Equipped with White & Silver ....................58

Pullback printing (White  Metallic silver/CMYKLclm) ..............58

Pullback printing (Metallic silver/CMYKLcLm  White) .............64

4-2 Performing Texture Printing: Equipped with Silver .................70

What is Texture Printing? ...........................................................70

Create The Texture Printing Data ..............................................70

Performing Texture Printing .......................................................73

Printing a Texture Chart .............................................................73

4-3 Maintenance ..........................................................................75

When Dot Drop-out Etc. Cannot be Corrected ..........................75

57

4-1 Pullback printing: Equipped with White & Silver

Pullback printing (White  Metallic silver/CMYKLcLm)

This section describes how to perform printing in the sequence of white and then metallic silver/CMYKLcLmcolor. After performing printing using white ink and allowing the ink to dry for a predetermined period, the media is pulled back once, and then the fill overprinting is performed using metallic silver and CMYKLcLm ink.

The printing data containing metallic colors such as "RDG_MetallicSilver" and "RVW-MT-Bronze" must be used in order to use the metallic silver ink, and the printing data containing "RDG_WHITE" must be used in order to use the white ink.

 P. 12, "2-3 Creating Printing Data"

This printing method involves some important notes for avoiding contamination on the printed surface. Be sure to refer to page 6, “When Performing Pullback Printing”.

Image of overprinting in the sequence of white and then metallic silver/CMYKLcLm

Transparent media

You will have the printed image from this side (the printed surface of the finished results).

White

Metallic silver / CMYKLcLm

1.

Printing With White Ink Only

 Make sure that you have finished making the preparations for VersaWorks, creating

the printing data, and getting the printer ready ( p. 9, "Chapter 2 Getting Ready").



58

Chapter 4 Advanced Chapter 4 Advanced

Chapter 4 Advanced










Click .


Clear Film [MT]" or "xxx :PET Clear Film,

Adhesive [MT]".




With [Mode], select the print mode "White

(v) ."

This prints with RDG_WHITE only.

Click .


Click .

With [Other Controls], select “User Custom Settings.”

For [Dry Time], select “15 minutes.”

This is a suggested setting for when using an auxiliary drying unit (DU series).


59


 Click .


Turn on the [Return to Origin After Print] option.




Film.  P. 30

NOTE: This section only described the settings that are necessary for the use of the white ink. For other settings, refer to the online help provided for VersaWorks.


 Go to “Job List” and click the “Queue A” tab, and drag the printing data to the queue

A job list.

60







Areas using “RDG_WHITE” are displayed with shading in transparent magenta.

Select the print job in the job list, then click .


After printing and dry time, the media is pulled back.

Continue printing of areas using metallic silver and

CMYKLcLm colors.


61


2.

Printing With Metallic Silver/CMYKLcLm Color

 Double-click the print job that was used in the step

1.

The “Job Setting” window appears.

62

 < When performing blend print with metallic silver / CMYKLcLm >

Click .



With [Mode], select the print mode "

CMYKLcLmMt (v) onWhite ."

This prints the areas where metallic color, such as RDG_MetallicSilver and RVW-MT-Bronze, and

CMYKLcLm colors are specified.

< When performing layered print with metallic silver / CMYKLcLm >

Click .



With [Mode], select the print mode "Mt

-> CMYKLcLm (v)."














Click .

With [Other Controls], select "Use Default Media Settings."

Click .

Turn off the [Return to Origin After Print] option.

Click [OK] to close the “Job Setting” window.

Select the print job in the job list, then click

.


After printing, allow the ink to dry sufficiently. We strongly recommend performing lamination.

When continuing printing using another data that uses metallic silver, white, and CMYKLcLm colors, repeat steps on and after

1.

. Also, if you want to modify detailed settings for each job, it will be convenient to perform modifications in the “Job Setting” window (displayed by doubleclicking the print job in the job).


63


Pullback printing (Metallic silver/CMYKLcLm  White)

This section describes how to perform printing in the sequence of metallic silver/CMYKLcLm Color and then white. After performing printing using metallic silver and CMYKLcLm ink and allowing the ink to dry for predetermined period, the media is pulled back once, and then the fill overprinting is performed using white ink.

The printing data containing metallic colors such as “RDG_MetallicSilver” and “RVW-MT-Bronze” must be used in order to use the metallic silver ink, and the printing data containing RDG_WHITE” must be used in order to use the white ink.

 P. 12, “Creating Printing Data”

This printing method involves some important notes for avoiding contamination on the printed surface. Be sure to refer to page 6, “When Performing Pullback Printing”.

Image of overprinting in the sequence of metallic silver/CMYKLcLm and then white.

Transparent media

You will have the printed image from this side (the opposite side of the printed surface of the finished results).

White

Metallic silver / CMYKLcLm

1.

Printing With Metallic Silver/CMYKLcLm Color

 Make sure that you have finished making the preparations for VersaWorks, creating

the printing data, and getting the printer ready ( p. 9, "Chapter 2 Getting Ready").


Queue A Properties window appears.

64




 < When performing blend print with metallic silver / CMYKLcLm >

Click .



Adhesive [MT]".




With [Mode], select the print mode

"CMYKLcLmMt (v) underWhite."



< When performing layered print with metallic silver / CMYK LcLm>

Click .



Adhesive [MT]".





"CMYKLcLm (v) -> Mt (v)."

This prints the areas where metallic color, such as

RDG_MetallicSilver and RVW-MT-Bronze, and CMYK

LcLm colors are specified.


65


 Click .






Click .

With [Other Controls], select “User Custom Settings.”

For [Dry Time], select “15 minutes.”

This is a suggested setting for when using an auxiliary drying unit (DU series).

Click .


Turn on the [Return to Origin After Print] option.


Film.  P. 30

NOTE: This section only described the settings that are necessary for the use of the metallic silver ink. For other settings, refer to the online help provided for VersaWorks.

66











Go to “Job List” and click the “Queue A” tab, and drag the printing data to the queue

A job list.


Select the print job in the job list, then click .


After printing and dry time, the media is pulled back.

Then, print the white areas.


67


2.

Printing With White Ink Only

 Double-click the print job that was used in the step

1.

The “Job Setting” window appears.





68


Click .




“White (v) .”

This prints with RDG_WHITE only.

Click .

With [Other Controls], select "Use Default Media Settings."








Click .

Turn off the [Return to Origin After Print] option.

Click [OK] to close the "Job Settings" window.

 Select the print job in the job list, then click

.


After printing, allow the ink to dry sufficiently. We strongly recommend performing lamination.

When continuing printing using another data that uses metallic silver, white, and CMYKLcLm colors, repeat steps on and after

1.

. Also, if you want to modify detailed settings for each job, it will be convenient to perform modifications in the “Job Setting” window (displayed by doubleclicking the print job in the job list).


69

4-2 Performing Texture Printing: Equipped with Silver

What is Texture Printing?

Texture printing is a printing method to produce texture patterns. This uses the texture patterns of the exclusive library to create and output the printing data. This document describes the texture printing using metallic silver ink.

* Create the printing data using the Adobe Illustrator version of CS or later if using Adobe Illustrator. If you use the earlier version before Adobe Illustrator 10 to create the printing data, the texture patterns may result in poor condition.

Create The Texture Printing Data

To create the data for the texture printing, please follow the instructions below.

The program used to create the printing data is Adobe Illustrator CS6. For detailed information on drawing methods and how to work with palettes, refer to the documentation or online help for Adobe Illustrator

CS6. If you're using another version of Adobe Illustrator, operations may be somewhat different from those explained here.

1.

Open the exclusive library.

 At the swatch palette menu, select [Open Swatch Library], then [Other Libraries].

The "Select Library" window appears.

* The swatch palette is displayed by going to the menu and selecting [Window], then [Swatch].

70




 Open folder in the order of [Computer] (or [My Computer]) → [Local Disk (C:)] →[Program Files] → [Roland VersaWorks] → [Swatch] → [Illustrator], and then select Roland

Metallic Texture System Library.ai.


Click [Open].

The exclusive swatch libraries “Roland Metallic Texture System Library.ai“ is displayed.

When this screen is displayed, click "OK."

By saving the ".ai" file selected in step



into the folder below, you can register each swatch library to the Adobe Illustrator's library. Once the registration is performed, you can open the library directly from the swatch palette menu, eliminating the need to search the file every time you start Adobe Illustrator.

C:\Program Files\Adobe\Adobe Illustrator CS6\Presets\(language abbreviation)\Swatches

* "C" is the name of your computer's local disk.

*The language abbreviation differs depending on the language used.

*Depending on the Illustrator used, "\Preset\Swatch" may be used instead of "\Presets\(language abbreviation)\Swatch" is "\Preset\Swatch."


71


2.

Create Illustrations and Specify Texture Patterns You Wish to Use

 Create the illustration.

Be sure to draw the illustration in the CMYK mode.

 Assign the desired texture patterns to the areas for the texture printing.

The areas where the texture patterns are assigned shall be printed with metallic silver ink. When the metallic silver ink is to be used for the printings other than the texture printing, other special spot colors shall be used. For the detailed usage, please refer to “Chapter 2 Getting Ready”.

The area to be printed with the texture pattern

 From " Roland Metallic Texture System Library," specify the texture pattern such as RTSL-MT-Standard-020.

* The name of the texture pattern is displayed on the data of Illustrator. The texture of the displayed image appears rougher than that of the actual print.

3.

Create the PS (PostScript) file.

Create a PS file as referring to the steps of the procedure

3.

in "Creating Data for Printing" in pages 15 to 17.

72




Performing Texture Printing

Procedure

 'Prepare the printing data having been created in the previous process which is described in “Create The Texture Printing Data” on page 70.

 Make the setting to output metallic silver ink with the VersaWorks, and execute the printing.

To use the metallic silver ink, you need to select "CMYKLcLmMt", etc. in the print mode of VersaWorks. For the detailed method of setting, please refer to “Chapter 3 Printing”.

Printing a Texture Chart

The texture chart is the printing sample of the texture pattern. By printing the texture chart, you can confirm the “complete texture chart” representing the texture itself that can be printed with “Your Printer” and “Your

Media” (slight pattern differences is possible to occur depending on the conditions of the printer and media.)

By selecting a pattern from this texture chart and creating the printing data using that selected pattern, you can print your intended pattern almost perfectly.

Procedure

 Double-click .

The [Queue A Properties] window appears.

 Click , configure the settings in [Quality Settings] and [Color Management].

Click [OK].

Note: When printing a texture chart, the [Quality] settings from the [Queue Properties] window are always applied. Since you cannot change the quality settings for the job using the [Job Settings] window after it has been added, be sure to configure the settings in the [Queue Properties] window before performing the following operations.


73


 Click [Chart] under [Print Roland Texture

System Library] form the [Media] menu.



This message appears: The following job will be printed. Do you want to continue? Check that the media in the printer is large enough for the displayed page size.

Click [OK].

The texture chart is added to the job list.

Click .

Rip'ing and printing the texture chart are performed.

* In the texture chart, color is added to part of the background of the texture. This makes the design of the texture clear.

74



4-3 Maintenance

When Dot Drop-out Etc. Cannot be Corrected

When using metallic silver ink and white ink, ink discharge may become unstable (resulting in dot drop-out, etc.) if the machine is left unattended for a long period. This is due to the properties of metallic silver ink and white ink containing ingredients which tend to settle and separate, which will cause the precipitated ingredients to solidify when the machine is left unattended for a long period. In such cases, perform "ink renewal" menu. For information on how to operate the "ink renewal" menu, refer to the User's Manual.

 “User’s Manual” ("When Problems Such As Dot Drop-out are not cleared up")

If the problems, such as dot drop-out, cannot be corrected even after performing cleaning above, then contact your authorized Roland DG Corp. dealer.


75

76

R2-121116

No results