YARD MACHINES 614 E, E602 E, E642 E, F, E662 E, H, E644 E, E664 F, E6A4 E snow thrower Operator's Manual

PDF

Dokument

Oglas

PERATOR’S

ANUAL

Model Numbers

E602E,E642E,

E642F, E662E,

E662H, 614E,

E644E, E664F,

E6A4E

Model Style 4 Shown

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning:

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.

MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722

PRINTED IN U.S.A.

FORM NO. 770-10003B

6/99

SECTION 1: FINDING YOUR MODEL NUMBER

This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says.

Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in this Operator’s Manual. The information on the model plate is very important if you need help from your dealer or the MTD customer support department.

• Every snow thrower has a model plate. You can locate it by standing behind the unit in the operating position and looking down at the rear frame below the engine. See Figure 1.

This is where your model number will be.

XXX-X-XXX-X-XXX XXXXXXXXXXX

This is where your serial number will be.

Copy the model number here:

MTD PRODUCTS INC

CLEVELAND, OHIO 44136

Copy the serial number here:

Figure 1

SECTION 2: CALLING CUSTOMER SUPPORT

• LOCATE YOUR MODEL NUMBER AND SERIAL NUMBER — Record this information in the space provided. To find your unit’s specific model number and serial number, see SECTION 1: FINDING

YOUR MODEL NUMBER.

• If you are having difficulty assembling this product or if you have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department.

• Customer Support can be reached by dialing: 1- (330) 220-4MTD

(4683)

1- (800)-800-7310

• Please have your model number and serial number ready when you call.

• Although both numbers are important, you will be asked to enter only your

serial

number before your call can be processed.

SECTION 3: IMPORTANT SAFE OPERATION PRACTICES

WARNING:

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF

NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF

YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH

THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS

SYMBOL-HEED ITS WARNING.

WARNING

:

The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

DANGER:

Your snow thrower was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.

1. TRAINING

• Read this operator's manual carefully in its entirety before attempting to assemble or operate this machine. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

• Never allow children under 14 years old to operate a snow thrower. Children 14 years old and over should only operate snow thrower under close parental supervision. Only persons well acquainted with these rules of safe operation should be allowed to use your snow thrower.

• No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions.

• Keep the area of operation clear of all persons, especially small children and pets.

• Exercise caution to avoid slipping or falling, especially when operating in reverse.

2. PREPARATION

• Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects.

• Disengage all clutches and shift into neutral before starting engine.

• Do not operate equipment without wearing adequate winter outer garments. Do not wear jewelry, long scarfs or other loose clothing which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

• Before working with gasoline, extinguish all cigarettes and other sources of ignition. Check the fuel before starting the engine. Gasoline is an extremely flammable fuel. Do not fill the gasoline tank indoors, while the engine is running, or until engine has been allowed to cool at least two minutes. Replace gasoline cap securely and wipe off any spilled gasoline before starting the engine as it may cause a fire or explosion.

• Use a grounded three wire plug-in for all units with electric drive motors or electric starting motors.

• Adjust collector housing height to clear gravel or crushed rock surface.

• Never attempt to make any adjustments while engine is running (except where specifically recommended by manufacturer).

• Let engine and machine adjust to outdoor temperature before starting to clear snow.

• Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction.

3. OPERATION

• Do not put hands or feet near or under rotating parts. Keep clear of discharge opening and auger at all times.

• Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

• After striking a foreign object, stop the engine, remove wire from spark plug, and thoroughly inspect the snow thrower for any damage. Repair the damage before restarting and operating the snow thrower.

• If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble.

• Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections. Never place your hand in the discharge or collector openings.

Use a stick or wooden broom handle to unclog the discharge opening.

• Take all possible precautions when leaving the unit unattended. Disengage the collector/impeller, stop the engine, and remove the key.

• When cleaning, repairing, or inspecting, make certain collector/impeller and all moving parts have stopped. Disconnect spark plug wire and keep away from plug to prevent accidental starting.

• Do not run engine indoors, except when starting engine and transporting snow thrower in or out of building. Open doors. Exhaust fumes are dangerous.

• Do not clear snow across the face of slopes.

Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes.

• Never operate snow thrower without guards, plates, or other safety protection devices in place.

• Never operate snow thrower near glass enclosure, automobiles, window wells, drop off, etc., without proper adjustments of snow thrower discharge angle. Keep children and pets away.

• Do not overload machine capacity by attempting to clear snow at too fast a rate.

• Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

• Never direct discharge at bystanders or allow anyone in front of unit.

• Disengage power to collector/impeller when transporting or not in use.

• Use only attachments and accessories approved by the manufacturer of snow thrower (such as wheel weights, counter weights, cabs, etc.).

• Never operate the snow thrower without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

• Muffler and engine become hot and can cause a burn. Do not touch.

4. MAINTENANCE AND STORAGE

• Check shear bolts, engine mounting bolts, etc., at frequent intervals for proper tightness to be sure equipment is in safe working condition.

• Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow engine to cool before storing in any enclosure.

• Always refer to operator's manual instructions for important details if snow thrower is to be stored for an extended period.

• Run machine a few minutes after throwing snow to prevent freeze up of collector/impeller.

• Check clutch controls periodically to verify they engage and disengage properly and readjust if necessary. Refer to operator's manual for adjustment instructions.

WARNING - YOUR RESPONSIBILITY:

Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

EET

DANGER

AVOID INJURY FROM

KEEP HANDS, F

AND CLOTHING AWAY.

ATING AUGER ROT

WARNING

STOP ENGINE BEFORE REMOVING

DEBRIS AND SERVICING UNIT.

KEEP CLEAR OF IMPELLER WHILE

ENGINE IS RUNNING.

NEVER DIRECT DISCHARGE AT

BYSTANDERS OR WINDOWS OR

ALLOW ANYONE IN FRONT OF

UNIT.

THOROUGHLY INSPECT THE AREA

WHERE THE EQUIPMENT IS TO BE

USED AND REMOVE ALL DOOR

MATS, SLEDS, BOARDS, WIRES AND

OTHER FOREIGN OBJECTS.

REFER TO OWNERS MANUAL FOR

FULL INSTRUCTIONS.

Figure 2

SECTION 4: CONTENTS OF HARDWARE PACK

Lay out the hardware according to the illustration for identification purposes. Parts are illustrated approximately one-half size. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.)

ATTACHING THE HANDLE ASSEMBLY

ATTACHING THE CHUTE ASSEMBLY

Hex Bolts

5/16-18 x 1-3/4" Long

(710-3180)

Hex Bolts

1/4-20 x 3/4" Long

(710-3015)

Hex Bolts

5/16-18 x 3/4" Long

(710-3008)

Saddle

(784-5599)

Lock Washers

5/16" I.D.

(736-0119)

Hex Lock Nuts

1/4-20 Thread

(712-3027)

Chute Flange

Keepers

(731-0851A)

Carriage Bolts

5/16-18 x 1-1/2" Long

(710-0262)

Hex Nuts

5/16-18 Thread

(712-3010)

C ATTACHING THE CHUTE DIRECTIONAL

CONTROL

Flat Washers

3/8” I.D. x 5/8” O.D.

(736-0185)

Cupped Washer

5/16” I.D.

(736-0242)

ATTACHING THE SHIFT ROD

AND CLUTCH CABLES

Ferrule

(711-0677)

Hairpin Clips

(714-0104)

Flat Washers

5/16" I.D. x 5/8" O.D.

(736-0264)

Hex Nuts

#10-24 Thread

(712-0121)

Eyebolt Not Shown

(747-0697)

Hairpin Clip

(714-0104)

Hex Nuts

5/16-18 Thread

(712-3010)

AUGER SHEAR BOLTS

NOTE: The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or an ice jam, the snow thrower is designed so that the bolts may shear. Two replacement shear bolts and nuts are provided for your convenience. Store in a safe place until needed.

“Z”-Fitting (R)

(746-0778)

ATTACHING THE CLUTCH GRIPS

Hex Screw 5/16-18 x 2.0 (710-0116)

Shear Bolts

5/16-18 x

1-1/2" Long

(710-0890A)

Hex Lock Nuts

5/16-18 Thread

(712-0429)

Spacer

.325 I.D. x .50 O.D. x .25

(750-1032)

Hex Top L-Nut

5/16-18 (712-0429)

SECTION 5: ASSEMBLY INSTRUCTIONS

This operator’s manual covers various models of snow throwers. The units illustrated may vary slightly from your unit. Follow only those instructions which pertain to your model snow thrower.

Attaching the Handle Assembly.

(Hardware A and E)

Lay loose parts out on flat surface.

IMPORTANT:

After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit.

Handle Panel

Right Handle

Left Handle

Traction Control

Grip

Right Grip Bracket

Auger Control Grip

Left Grip Bracket

NOTE:

All references to right or left side of the snow thrower are determined from behind the unit in the operating position.

UNPACKING

Remove staples or break glue on the top flaps of the carton. Remove any loose parts like operator’s manual or hardware pack included with unit.

Cut corner’s and lay end of carton down flat.

Remove packing material.

Roll unit out of carton. Check carton thoroughly for loose parts.

Extend cables out behind unit and lay them on the floor.

Lay out the contents of the hardware pack according to the illustration in section 4 and identify each part.

Find the loose parts in the carton and lay these on the floor. See Figure 3. You should locate the following loose parts in the carton:

7 6

Figure 3

Attach left handle and left grip bracket to handle panel with two carriage bolts, lock washers and hex nuts. (Be sure the bend in the grip bracket is towards the center of the handle panel. (See

Figure 4.) Do not tighten at this time.

Handle Panel

Right Handle

Left Handle

Auger Control Grip

Traction Control Grip

Right Clutch Grip Bracket

Left Clutch Grip Bracket

Shift Rod (Not Illustrated)

Chute Directional Control Assembly

(Not Illustrated)

10.

Chute Assembly (Not Illustrated)

11.

Hardware Pack (Not Illustrated)

Outer

Edge of Handle

Panel

Carriage

Bolts

Left Handle

(curves in)

Left Grip Bracket

Handle Panel

Hex Nuts

TOOLS REQUIRED

The snow thrower comes partly assembled in the carton. You will have to complete the assembly.

Follow assembly instructions in this operator’s manual to make the job safe and easy. You will need the following tools to assemble the snow thrower.

Set of Wrenches (3/8", 9/16", 1/2" or adjustable)

Pair of pliers

Lock Washers

Figure 4

Locate auger control grip, part #4 in Figure 3.

The triangular metal tab on the auger control grip must face the center of the handle panel.

Insert curved end of the Z fitting into the top hole in the triangular metal tab on the auger control grip. See Figure 5.

Auger Control

Grip

Triangle

Metal Tab

Repeat process for the right side Traction

Control Grip.

Lay handle assembly behind snow thrower. See

Figure 7.

“Z” Fitting

Hex Bolt

Figure 5

Place the auger control grip on top of the left handle. The triangular metal tab must be between the handle and the grip bracket. See

Figure 6.

Triangle

Metal Tab

Lock Washer

Figure 7

Insert a hex bolt 3/4” long and lock washer through the lower hole on the bottom of the handle. See Figure 7.

Hold the handle assembly up to the bottom of the snow thrower frame and thread the hex bolt into the lower hole in snow thrower frame. Do not tighten at this time. See Figure 8.

Left

Handle

Spacer

Auger Control Grip

Left Grip Bracket

Hex Lock Nut

Hex

Screw

Handle

Panel

“Z” Fitting

Figure 6

Secure with hex bolt, spacer and lock nut. See

Figure 6. (Do not overtighten this bolt as it will prevent the grips from automatically returning to their upright position.)

Figure 8

10. Repeat process on the other side.

11. Raise the handle assembly into the upright position and align the top holes in the handles with the top holes in the snow thrower frame.

Attach using hex bolts 1 3/4” Long, lock washers and saddles. (Curve in saddle must match the curve in the handle.) See Figure 9.

12. Tighten all hardware used to attach the handle assembly to the snow thrower frame.

Flat

Washer

Lock

Washers

Cable

Roller

Guide

Handle

Tab

Hex

Bolt 1-3/4”

Long

Hex Bolt

3/4” Long

Figure 9

ATTACHING SHIFT ROD

(Hardware D)

Place the shift lever in the fastest forward speed position.

Models 602, 642, 662: Rotate the shift arm assembly counter clockwise, as far as it will go.

Insert the shift rod through the shift arm assembly. When installed the shift arm assembly should point to the right. Secure with flat washer and hairpin clip. See Figure 10.

Models 614, 644, 664 and 6A4: Rotate the shift arm assembly counter clockwise as far as it will go. Insert the shift rod through the shift arm assembly. When installed, the shift arm assembly should point left. Secure with flat washer and hairpin clip. See Figure 11.

Traction

Drive

Clutch

Flat

Washer

Shift

Lever

Ferrule

(Bottom

Hole)

Hairpin

Clip

Shift

Rod

Flat

Washer

Hairpin

Clip

Shift

Arm

Assembly

Models 602, 642 and 662

Figure 10

Hairpin

Clip

Shift

Lever

Ferrule

Shift

Rod

Flat

Washer

Hairpin

Clip

Shift

Arm

Assembly

Models 614, 644, 664, and 6A4

Figure 11

Models 602, 642, 662: Thread the ferrule up or down the shift rod and align with the lower hole on the shift lever assembly behind the handle panel.

See Figure 10 .

Models 614, 644, 664, and 6A4: Thread the ferrule onto the shift rod, up or down the shift rod and align with the far hole on the narrow side of the shift lever assembly behind the handle panel. See

Figure 11.

Secure the ferrule to the shift arm assembly with flat washer and hairpin clip.

NOTE:

Make certain to check for correct adjustment of the shift rod as instructed in the FINAL

ADJUSTMENTS section before operating the snow thrower.

ATTACHING CLUTCH CABLES

(Hardware D)

Thread the hex jam nuts all the way up the threaded portion of the “Z” ends.

Make certain all cables are in the grooves of the cable roller guides. The roller guides are located in the lower rear of the unit. Lift the clutch grip in the raised (up) position.

Thread the cable onto the threaded portion of the “Z” end until there is no slack in the cable, but the cable is NOT tight. Do not overtighten cable. See Figure 12.

WARNING:

If cable is tightened so there is tension on the cable with the clutch grip released, the safety features

of the snow thrower may be overridden.

Carriage Bolts

Hex Lock Nuts

“Z”

Hex

Nut

Cable is

Straight

Figure 12

When correct adjustment is reached, tighten the hex nut against the cable to lock it in position.

ATTACHING THE CHUTE ASSEMBLY

(Hardware B)

Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit.

Place chute flange keepers beneath lip of chute assembly, flat side down.

Insert hex bolt up through chute flange keeper and chute assembly as shown in Figure 13.

Secure with hex lock nut.

After assembling all three chute flange keepers, tighten all nuts and bolts securely, then back off

1/4 turn to allow easier movement.

Chute

Directional

Control

Bracket

Figure 14

Place one flat washer over the end of the chute directional control, then insert the end of the chute directional control into the hole in the plastic bushing in the chute bracket. See Figure

15. Place the second flat washer on the chute directional control, and secure with hairpin clip.

Flat Washer

Chute Directional

Control

Hairpin Clip

Chute Directional

Control Bracket

Figure 15

Thread one hex nut onto the eyebolt on the chute directional control assembly until there is at least two inches of threads showing between the nut and the head of the eyebolt. See Figure 16.

Chute

Assembly

Hex Bolt

Cup

Side

Crown

Side

Left

Handle

Hex Nut

Cupped

Washer

Eyebolt

Hex Lock Nut

Chute Flange

Keeper

Figure 13

ATTACHING THE CHUTE DIRECTIONAL

CONTROL (Hardware C)

Loosen the two hex nuts which secure the lower chute directional control support bracket to the snow thrower housing. See Figure 14.

2” of

Threads

Figure 16

Hex Nut

Place the eyebolt into the hole located half way up the left handle. Secure with cupped washer

(cupped side against the handle, see inset) See

Figure 16.

Adjust the chute directional control support bracket (see figure 15) so that the spiral on the chute directional control fully engages the teeth on the chute assembly. Tighten the hex nuts on the lower chute directional control bracket securely. Tighten the hex nuts on the eyebolt.

Check to make sure all nuts and bolts on the control panel and all four bolts which secure the handles to the frame are tight.

LAMP WIRING (If Equipped)

Lamp Wire

Alternator

Lead

Right Handle

Now release the traction control clutch grip, and push the unit again. Move the shift lever back to the fast reverse position, then all the way forward again. There should be no resistance in the shift lever, and the wheels should keep turning.

If you have resistance when moving the shift lever or the wheels stop when they should not, loosen the jam nut on the traction control cable and unthread the cable one turn. If the wheels do not stop when you engage the traction control clutch grip, loosen the jam nut on the traction control cable and thread the cable in one turn. Recheck the adjustment and repeat as necessary.

Tighten the jam nut to secure the cable when correct adjustment is reached.

Figure 17

Wrap the wire from the lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank. See

Figure 17. Be sure lamp wire does not interfere with the movement of any controls or cables.

NOTE:

If you are uncertain that you have reached the correct adjustment, refer to SECTION 8:

ADJUSTMENTS.

IMPORTANT:

After attaching the shift rod and clutch cables, check the adjustments as instructed, and make any final adjustments necessary before operating your snow thrower. Failure to follow the instructions may cause damage to the snow thrower.

FINAL ADJUSTMENTS

Auger Control Clutch

To check the adjustment of the auger control clutch, push forward on the left hand clutch grip depressing the rubber bumper under the clutch grip. There should be slack in the cable.

Release the clutch grip. The cable should be straight. Make certain you can depress the auger control clutch grip against the left handle completely.

If necessary, loosen the hex jam nut and thread the cable in (for less slack) or out (for more slack) as necessary. Refer to Figure 12. Recheck the adjustment. Tighten the jam nut against the cable when correct adjustment is reached.

Adjusting The Skid Shoes

The space between the shave plate and the ground can be adjusted by adjusting the skid shoes.

Place skid shoes in the low position to remove snow close to the ground. Place skid shoes in a higher position to remove snow from uneven ground. See Figure 18.

Adjust skid shoes by loosening the four hex nuts and carriage bolts and moving skid shoes to desired position. Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. Retighten nuts and bolts securely.

Traction Control Clutch and Shift Lever

Adjustment

To check the adjustment of the traction control clutch and shift lever:

Move the shift lever all the way to the highest speed. With the traction control lever released, push the snow thrower forward. The unit should roll forward.

Then engage the traction control clutch grip. The wheels should stop turning.

Skid

Shoe

Hex Nuts

Carriage

Bolts

Figure 18

Low Position

High Position

WARNING:

It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury and/or damage to the snow thrower.

SECTION 6: CONTROLS

THROTTLE CONTROL

The throttle control is located on the engine. It regulates the speed of the engine. See Figure 20.

SAFETY IGNITION SWITCH

The ignition key must be inserted in the switch before the unit will start. Remove the ignition key when snow thrower is not in use.

FUEL SHUT-OFF

VALVE

The fuel shut-off valve, located under fuel tank, controls fuel flow from tank. (If equipped)

See Figure 19.

Closed

Open

Figure 19

Starter

Handle

TRACTION CONTROL CLUTCH

(See Figure 21 for Model 602, 642 and 662. See

Figure 22 for Models 614, 644, 664, and 6A4)

The traction control clutch is located on the right handle. Squeeze the traction control clutch to engage the wheel drive. Release to stop.

CHUTE DIRECTIONAL CONTROL

(See Figure 21 for Model 602, 642 and 662. See

Figure 22 for Models 614, 644, 664, and 6A4)

The chute directional control is located on left hand side of the snow thrower.

To change the direction in which snow is thrown, turn chute directional control as follows:

Crank clockwise to discharge to the left.

Crank counterclockwise to discharge to the right.

Auger

Control

Clutch

Traction

Control

Clutch

Ignition

Key

Choke

Throttle

Figure 20

Primer

SHIFT LEVER

(See Figure 21 for Model 602, 642 and 662. See

Figure 22 for Models 614, 644, 664, and 6A4)

The shift lever is located in the center of the handle panel. The shift lever may be moved into one of six positions. Run engine with throttle in the fast position. Use the shift lever to determine ground speed.

Forward—Five forward speeds: position one (1) is the slowest; position five (5) is the fastest.

Reverse—One reverse (R) speed.

NOTE:

Model 614, 644, 664, and 6A4 has five forward positions and two reverse.

AUGER CONTROL CLUTCH

(See Figure 21 for Model 602, 642 and 662. See

Figure 22 for Models 614, 644, 664, and 6A4)

The auger control clutch is located on the left handle. Squeeze the auger control clutch against the handle to engage the augers. Release to stop the snow throwing action.

Shift

Lever

Chute

Directional Control

Models 602, 642 and 662

Figure 21

Auger

Control

Clutch

Traction

Control

Clutch

Chute

Directional Control

Shift

Lever

Models 614, 644, 664, and 6A4

Figure 22

SECTION 7: OPERATION

BEFORE STARTING

WARNING:

Observe all Warning Labels on the snow thrower prior to use. See

Figure 2.

Your snow thrower is shipped with oil; however, you must check the oil level before operating. Be careful not to overfill.

The spark plug wire was disconnected for safety.

Attach spark plug wire to spark plug before starting

GAS AND OIL FILL-UP

Check oil level and add oil if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your snow thrower.

Read instructions carefully.

WARNING:

Never fill fuel tank indoors, with engine running or while engine is hot. Do not smoke when filling fuel tank.

TO START ENGINE

NOTE:

If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the

Final Adjustments section of SECTION 5:

ASSEMBLY INSTRUCTIONS.

Attach spark plug wire to spark plug. Make certain the metal loop on end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug. See Figure 23.

Make certain the fuel cutoff valve is in the OPEN

(vertical) position. See Figure 19.

Metal Loop on Spark

Plug Wire

Rubber Boot

Figure 23

Make certain the auger and drive clutch levers are in the disengaged (released) position.

Move throttle control up to FAST position. Insert ignition key into slot. See Figure 20. Be certain it snaps into place. Do not turn key.

ENGINE WILL NOT START

UNLESS IGNITION KEY IS IN-

SERTED INTO IGNITION

SLOT IN CARBURETOR

COVER. DO NOT TURN IGNI-

TION KEY.

Electric Starter: (If Equipped)

WARNING:

The electric starter is

equipped with a three-wire power cord and plug, and is designed to operate on

120 volt AC household current. It must be properly grounded at all times to avoid the possibility of electric shock which may be injurious to the operator.

Follow all instructions carefully. If the house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

Follow all instructions carefully. Determine that your house wiring is a three wire grounded system. Ask a licensed electrician if you are not certain. If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions. If your system is grounded and a threehole receptacle is not available at the point your starter will normally be used, one should be installed by a licensed electrician.

When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded receptacle.

When disconnecting the power cord, always unplug the end from the three-hole grounded receptacle first.

Make certain the auger control and traction control clutch grips are in the disengaged

(released) position.

Move throttle control up to FAST position. Insert ignition key into slot. Refer to Figure 20. Be certain it snaps into place. Do not turn key.

Rotate choke knob to OFF position.

NOTE: Do not prime engine.

Connect power cord to switch box on engine.

Plug the other end of power cord into a threehole, grounded 120 volt AC receptacle.

Push starter button on top of the engine to crank engine. As you crank the engine, move choke knob to FULL choke position.

When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF.

Repeat steps 6 and 7 until engine starts. If engine fails to start, repeat steps 5, 6, and 7 until engine starts.

As engine warms up and begins to operate evenly, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position.

Recoil Starter.

Make certain the auger control and traction control clutch grips are in the disengaged

(released) position.

Move throttle control up to FAST position. Insert ignition key into slot. Refer to Figure 20. Be certain it snaps into place. Do not turn key.

Rotate choke knob to FULL choke position (cold engine start).

If engine is warm, place choke in OFF position instead of FULL.

Push primer button two or three times. Refer to

Figure 20. If engine is warm, push primer button once only.

NOTE:

Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15

Grasp starter handle (refer to Figure 20) and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.

Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

Repeat steps 6 and 7 until engine starts. If engine fails to start, repeat steps 5, 6 and 7 until engine starts.

TO STOP ENGINE

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

To help prevent possible freeze-up of starter, proceed as follows.

Electric Starter:

Connect power cord to switch box on engine, then to

120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.

Recoil Starter:

With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.

To stop engine, remove the ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

NOTE:

Do not lose ignition key. Keep it in a safe place. Engine will not start without the ignition key.

Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times. Leave throttle control lever in the STOP or

OFF position. Leave choke control in the FULL choke position.

TO ENGAGE DRIVE/AUGER

With the engine running near top speed, move shift lever into one of the FORWARD or

REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use the slower speeds until you are familiar with the operation of the snow thrower.

Squeeze the left hand auger control clutch to engage auger.

While the left hand auger control clutch is engaged, engage the right hand traction control clutch.

NOTE:

NEVER move shift lever without first releasing the drive clutch.

TIRE CHAINS

(OPTIONAL)

Use tire chains when extra traction is necessary.

OPERATING TIPS

NOTE:

Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

WARNING: Temperature of muffler and surrounding areas may exceed 150 o

Avoid these areas.

• For most efficient snow removal, remove snow immediately after it falls.

• Discharge snow downwind whenever possible. Slightly overlap each previous swath.

• Set the skid shoes 1/4" below the scraper bar for normal usage. The skid shoes may be adjusted upward for hard-packed snow. Adjust downward when using on gravel or crushed rock.

• Be certain to follow the precautions listed under ‘‘To Stop Engine’’ in previous column to prevent possible freeze-up.

• Clean the snow thrower thoroughly after each use.

SECTION 8: ADJUSTMENTS

WARNING:

Never attempt to clean chute or make any adjustments while engine is running.

ADJUSTING CHUTE

You can control the distance that snow is thrown by adjusting the angle of the chute assembly. The sharper the angle, the shorter the distance snow is thrown.

To adjust the chute, loosen the hand knob. See

Figure 24.

Pivot the top of the chute assembly to the position desired.

Remove the frame cover underneath the snow thrower by removing the six self-tapping screws.

With the traction control clutch released, check if there is clearance between the friction wheel and the drive plate in all positions of the shift lever. For correct adjustment there has to be enough clearance.

With the traction control clutch engaged, check if the friction wheel is contacting the drive plate.

See Figure 25.

If adjustment is necessary, loosen the jam nut on the traction control cable, and thread cable in or out as necessary.

Tighten the jam nut to secure the cable when correct adjustment is reached. Reassemble the frame cover with six self-tapping screws.

Friction

Wheel

Hand

Knob

Gear

Shaft

Figure 24

ADJUSTING SKID SHOE

The space between the shave plate and the ground can be adjusted by adjusting the skid shoe. Slide the skid shoe upwards and lower the housing to remove snow close to the ground. Slide skid shoe downwards and raise the housing to remove snow from uneven ground like gravel. For more details, refer to Adjusting the Skid Shoes in section 5.

Drive

Plate

Figure 25

ADJUSTING TRACTION CONTROL

CLUTCH

Note:

If you had earlier placed plastic film under the gas cap, be sure to remove it once the adjustment to the traction control clutch is done and the snow thrower frame is re-installed.

Refer to the Final Adjustments section on page 10 for instructions to adjust the traction control clutch. If you are not sure whether you have been able to adjust the traction control clutch properly, check as follows.

ADJUSTING AUGER CLUTCH

Drain the gasoline from the snow thrower or put a plastic film under the gas cap if the snow thrower has already been operated. Tip the snow thrower forward onto the auger housing.

To adjust the auger clutch, refer to the Final

Adjustments in section 5.

ADJUSTING SHIFT ROD

Remove the hairpin clip and flat washer from the ferrule and remove the ferrule from the shift lever. Place the shift lever in the fastest forward speed position.

Models 602, 642, 662:

Push up on the shift arm assembly as far as it will go. Thread the ferrule up or down the shift rod and align with the lower hole on the wider side of the shift lever assembly behind the handle panel. Secure the ferrule to the shift arm assembly again with the hardware earlier removed.

Models 614, 644, 664, and 6A4:

Push down on the shift arm assembly as far as it will go. Thread the ferrule up or down the shift rod and align it with the hole closest to the shift knob on the narrow side of the shift lever assembly behind the handle panel.

NOTE:

Make certain to check for correct adjustment of the shift rod as instructed in the Final

Adjustments section before operating the snow thrower.

CARBURETOR ADJUSTMENT

WARNING:

If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler.

Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude and load.

Refer to the separate engine manual packed with your unit for carburetor adjustment information.

DRIVE WHEELS

The wheels may be adjusted for two different methods of operation. The adjustment is made by placing the klick pins in one of two different holes on the right side of the unit. See Figure 26.

One Wheel Driving—Place klick pin in the outside axle hole on the right side. This position gives power drive to the left wheel only, making the unit easier to maneuver.

Both Wheels Driving—Place klick pin in the hole in the hub next to the rim on the right side.

This position is good for heavy snow as there is power drive in both wheels.

Klick Pin in Hole in Hub Next to Rim

Outside Hole in Axle

Figure 26

SECTION 9: LUBRICATION

WARNING:

Disconnect the spark plug wire and ground against the engine before performing any lubrication or maintenance.

ENGINE

Refer to engine manual for all engine lubrication instructions.

WARNING:

When following instructions in separate engine manual for draining oil, be sure to protect frame to avoid oil dripping onto transmission parts.

CHUTE DIRECTIONAL CONTROL

The gear on the end of the chute directional control should be greased with multi-purpose automotive grease once a season.

AUGER SHAFT

At least once a season, remove shear bolts on auger shaft. Oil or spray lubricant inside shaft. See Figure

27. Also lubricate the auger bearings at least once a season.

Shear

Bolts

Bearings

Figure 27

SPROCKET SHAFT

Lubricate the sprocket shaft with a light oil at least once a season or after every 25 hours of operation.

IMPORTANT:

Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

DRIVE AND SHIFTING MECHANISM

At least once a season or after every 25 hours of operation, remove the bottom frame cover. Lubricate any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. Use engine oil or a spray lubricant. Avoid getting oil on

rubber friction wheel and aluminum drive plate.

GEAR CASE

The gear case is lubricated with grease at the factory and does not require checking. If disassembled for any reason, lubricate with 2 ounces of shell grease, part number 737-0168.

IMPORTANT:

Do not overfill the gear case.

Damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

To remove skid shoes, remove the four carriage bolts, belleville washers and hex nuts which attach them to the snow thrower. Reassemble new skid shoes with the four carriage bolts, belleville washers

(cupped side goes against skid shoes) and hex nuts.

Make certain the skid shoes are adjusted to the same level on both sides.

To remove shave plate, remove the carriage bolts, belleville washers and hex nuts which attach it to the snow thrower housing. Reassemble new shave

to the inside of the housing. Tighten securely.

ENGINE

Refer to separate engine manual for all engine maintenance procedures.

BELT REMOVAL AND REPLACEMENT

WARNING:

Disconnect the spark plug wire from the spark plug and ground.

AUGER BELTS

NOTE:

It is necessary to remove both belts in order to change either one. If changing just one belt, be certain to check the condition of the other belt.

Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.

See Figure 28.

Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

Tip the snow thrower up and forward so that it rests on the auger housing.

SECTION 10: MAINTENANCE

AUGERS

The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. Refer to Figure 27. If you hit a hard foreign object or ice jam, the snow thrower is designed so that the hex bolts will shear.

If the augers will not turn, check to see if the bolts have sheared. Two replacement shear bolts and hex lock nuts have been provided with the snow thrower.

For future use, order part number 710-0890A (shear bolt 5/16-18 x 1.5" long) and 712-0429 (hex insert lock nut 5/16-18 thread).

Belt

Cover

Self-Tapping

Screws

SHAVE PLATE AND SKID SHOES

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary.

Figure 28

Remove six self-tapping screws from the frame cover underneath the snow thrower.

Rear

Auger

Belt

Drive

Belt

Engine

Pulley

Front

Auger

Belt

Friction

Wheel

Idler

Pulley

Engine

Pulley

Idler

Pulley

Figure 29

NOTE:

It may be necessary to loosen the six hex nuts that fasten the frame to the auger housing to aid in belt removal.

Roll the front and rear auger belts off the engine pulley. See Figure 29.

Unhook the idler spring from the hex bolt on the auger housing. See Figure 30.

Back out the stop bolt to allow the belts to slip between the bolt and auger pulley.

See Figure 31.

Lift the rear auger belt from the auger pulley, and slip belt between the support bracket and the auger pulley. See Figure 31. Repeat this step for front auger belt.

Replace both auger control belts by following instructions in reverse order.

DRIVE BELT

Follow steps 1 through 4 of previous instructions.

Pull idler pulley up, and lift belt off engine pulley, idler pulley, and friction wheel disc.

See Figure 29.

Back out the stop bolt until the support bracket rests on the auger pulley. See Figure 31.

Slip belt between friction wheel and friction wheel disc. See Figure 31. Remove and replace belt. Reassemble following the instructions in reverse order.

NOTE:

The support bracket must rest on the stop bolt after the new belt has been assembled. See

Figure 31.

Support

Bracket

Rear

Auger

Belt

Front

Auger

Pulley

Auger

Pulley

Idler

Spring

Auger

Housing

Support

Bracket

Spring

Figure 30

Friction

Wheel

Disc

Friction Wheel

Drive Belt

Stop

Bolt

Frame

Support Bracket

Figure 31

CHANGING THE FRICTION WHEEL

RUBBER

The rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and periodically thereafter. Replace the friction wheel rubber if any signs of wear or cracking are found.

Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

Tip the snow thrower up and forward, so that it rests on the auger housing.

Remove six self-tapping screws from the frame cover underneath the snow thrower.

Remove the klick pins which secure the wheels, and remove the wheels from the axle.

Using a 7/8" wrench to hold the shaft, loosen, but do not completely remove, the hex nut and bell washer on the left end of gear shaft. See Figure

32.

Lightly tap the hex nut to dislodge the ball bearing from the right side of frame. Remove the hex nut and bell washer from left end of shaft.

Slide the gear shaft to the right and slide the friction wheel assembly from the shaft.

Remove the six screws from the friction wheel assembly (three from each side). Remove the friction wheel rubber from between the friction wheel plates.

Reassemble new friction wheel rubber to the friction wheel assembly, tightening the six screws in rotation and with equal force.

10. Position the friction wheel assembly up onto the pin of the shift rod assembly, and slide the shaft through the assembly. Reassemble in reverse order.

Figure 32

Hex Nut

Bell

Washer

SECTION 11: OFF-SEASON STORAGE

WARNING:

Never store engine with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or other gas appliance.

If unit is to be stored over 30 days, prepare the engine for storage as instructed in the separate engine operator’s manual included with your unit.

Remove all dirt from exterior of engine and equipment.

Follow lubrication recommendations in section 9.

NOTE:

When storing any type of power equipment in a poorly ventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

SECTION 12: TROUBLE SHOOTING GUIDE

Trouble Possible Cause(s)

Engine fails to start Fuel tank empty, or stale fuel.

Engine runs erratic**

Blocked fuel line.

Choke not in ON position

Faulty spark plug.

Key not in switch on engine.

Spark plug wire disconnected.

Primer button not depressed.

Fuel shut-off valve closed

(if so equipped).

Improper gasoline and oil mixture.

Unit running on CHOKE.

Blocked fuel line or stale fuel.

Corrective Action

Fill tank with clean, fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used.

Clean fuel line.

Move switch to ON position

Clean, adjust gap or replace.

Insert key.

Connect spark plug wire.

Refer to the engine manual packed with your unit.

Open fuel shut-off valve.

Refer to the engine manual packed with your unit.

Water or dirt in fuel system.

Carburetor out of adjustment.

Loss of power Spark plug wire loose.

Gas cap vent hole plugged.

Exhaust port plugged.

Engine overheats Carburetor not adjusted properly.

Excessive vibration Loose parts or damaged auger.

Unit fails to propel itself

Unit fails to discharge snow

Incorrect adjustment of drive cable.

Drive belt loose or damaged.

Discharge chute clogged.

Foreign object lodged in auger.

Incorrect adjustment of drive cable.

Drive belt loose or damaged.

Move choke lever to OFF position.

Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last over thirty days unless a fuel stabilizer is used.

Drain fuel tank. Refill with fresh fuel.

Refer to the engine manual packed with your unit or have carburetor adjusted by an authorized service dealer.

Connect and tighten spark plug wire.

Remove ice and snow from cap. Be certain vent hole is clear.

Clean-see Maintenance section of engine manual.

Refer to the engine manual packed with your unit or have carburetor adjusted by an authorized service dealer.

Stop engine immediately and disconnect spark plug wire. Tighten all bolts and nuts. Make all necessary repairs. If vibration continues, have unit serviced by an authorized service dealer.

Adjust drive cable. Refer to Adjustment section of this manual.

Replace drive belt. Refer to Belt Replacement in Maintenance section of this manual.

Stop engine immediately and disconnect spark plug wire. Clean discharge chute and inside of auger housing.

Stop engine immediately and disconnect spark plug wire.

Remove object from auger.

Adjust drive cable. Refer to Adjustment section of this manual.

Replace drive belt. Refer to Belt Replacement in Maintenance section of this manual.

Note:

For repairs beyond the minor adjustments above, contact your local authorized service dealer.

Blower Housing

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

31 30

Blower Housing

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

REF.

PART

NO.

1 712-0116

2 756-0178

3 784-5632A

4 710-0459A

5 741-0475

6 736-0242

7 712-3010

8 712-0324

9 736-0463

10 705-5226

11 731-1379A

12 710-0703

13 710-0451

14 738-0281

15 736-0174

16 712-3068

17 732-0611

18 736-0119

19 05931

20 741-0309

21 684-0039C

684-0040C

684-0041C

684-0055B

22 736-0169

23 712-0798

24 784-5580

DESCRIPTION

Lock Jam Nut 3/8-24

Flat Idler

Auger Idler Arm

Hex Cap Screw 3/8-24 x 1.50

Bushing

Bell Washer

Hex Nut 5/16-18

Hex Lock Nut 1/4-20

Flat Washer

Reinforcement Chute

Chute Adapter

Carriage Screw 1/4-20 x .62

Carriage Bolt 5/16-18

Shoulder Screw

Wave Washer

Hex Nut 5/16-18

Extension Spring

Lock Washer 5/16

Bearing Housing

Ball Bearing

24” Housing Assembly

26” Housing Assembly

28” Housing Assembly

30” Housing Assembly

Lock Washer 3/8

Hex Nut 3/8-16

Slide Shoe

REF.

PART

NO.

25 784-5581A

784-5579A

784-5582A

784-5575

26 684-0065

27 715-0114

28 618-0120

618-0121

618-0122

618-0160

29 710-0604

30 784-5618

31 741-0245

32 736-0188

33 741-0493A

34 605-5188A

605-5192A

605-5196A

605-5248A

35 605-5189A

605-5193A

605-5197A

605-5249A

36 710-0890A

37 712-0429

38 784-5647

DESCRIPTION

24” Shave Plate

26” Shave Plate

28” Shave Plate

30” Shave Plate

Impeller Assembly

24” Gear Assembly

26” Gear Assembly

28” Gear Assembly

30” Gear Assembly

Hex Washer Screw 5/16-18

Bearing Housing

Hex Flange Bearing

Flat Washer

Flange Bushing

Spiral 24” RH

Spiral 26” RH

Spiral 28” RH

Spiral 30” RH

Spiral 24” LH

Spiral 26” LH

Spiral 28” LH

Spiral 30” LH

Shear Bolt 5/16-18 x 1.5

Lock Nut 5/16-18

Chute Directional Control Bracket

Handle Assembly

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

Handle Assembly

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

REF.

NO.

PART

NO.

1 712-0116

2 732-0193

3 736-0105

DESCRIPTION

Jam Lock Nut 3/8-24

Compression Spring

Bell Washer

4 784-5619A Shift Handle

5 710-0459A Hex Cap Screw 3/8-24

6 736-0275 Flat Washer

7 714-0104

8 720-0232

9 711-0677

Cotter Pin

Shift Knob

Ferrule

10 726-0100

11 747-0921

Push Cap

Shift Rod

12 720-0201A Chute Knob

13 705-5204A Chute Directional Control

14 747-0697 Eyebolt

735-0234 Grommet only

15 684-0008A Shift Arm Assy

16 720-0274 Grip

17 705-5233 Clutch Lever Assy LH

705-5234

18 750-1032

Clutch Lever Assy RH

Spacer

19 735-0199A Rubber Bumper

20 746-0778

21 705-5275

22 712-0429

23 736-0119

24 712-3010

25 705-5274

Cable

Lever Bracket LH

Lock Hex Nut 5/16-18

Lock Washer 5/16

Hex Nut 5/16-18

Lever Bracket RH

REF.

NO.

PART

NO.

26 749-0910B

27 710-3103

28 710-0262

29 684-0104

684-0145

684-0106

30 749-0911B

34 784-5599

35 710-3180

DESCRIPTION

Handle RH

Hex Cap Screw 5/16-18 x 1.75

Carriage Bolt 5/16-18 x 1.50

Control Panel Assy - 2 Style

Control Panel Assy- 2 Style w/light

Control Panel Assy - 4 Style

Handle LH

Handle Tab

Hex Cap Screw 5/16-18 x 2.0

36 710-3008

37 736-0185

38 731-0921

39 736-0159

40 710-0451

41 710-0276

Hex Cap Screw 5/16-18 x .75

Flat Washer

Upper Chute

5/16 Washer

Carriage Bolt 5/16-18 x .75

Carriage Screw 5/16-18 x 1.0

42 720-0284 Knob

43 731-1300A Lower Chute

44 712-3027 Hex Lock Nut 1/4-20

45 731-0851A Flange Keeper

46 710-3015 Hex Cap Screw 1/4-20 x .75

47 629-0058 Round Light Harness

48 710-1652

49 710-1003

50 712-0415

51 725-1300

52 731-1317

53 736-0242

Hex Tap Screw 1/4-20 x .625

Hex Screw

Hex Nut

Headlight 18 Watts

Headlight Cover

Bell Washer

REF.

NO.

PART

NO.

618-0123

618-0124

710-0642

711-0908

711-0909

711-0910

711-1024

714-0161

715-0143

717-0526

717-0528

718-0186

DESCRIPTION

Housing—R.H.

Housing—L.H.

Hex Screw 1/4-20 x .75

Spiral Axle 24"

Spiral Axle 26"

Spiral Axle 28"

Spiral Axle 30”

Key

Pin-Spiral

Shaft-Worm

Gear-Worm

Collar-Thrust

REF.

NO.

PART

NO.

9 721-0325

10 721-0327

11 736-0351

12 736-0369

13 736-0445

14 737-0168

15 741-0662

16 741-0663

17 618-0120

618-0121

618-0122

618-0160

Plug

Seal-Oil

Washer-Flat

DESCRIPTION

Washer-Flat

Grease

Bearing-Flange

Ass’y. Complete 24"

Ass’y. Complete 26"

Ass’y. Complete 28"

Ass’y Complete 30”

Frame Assembly

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

Drive Clutch

Cable

Auger Clutch

Cable

16” Wheels

13” or 15” Wheels

Auger Clutch

Cable

Blower

Housing

Frame Assembly

E602E, E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

REF.

NO.

PART

NO.

1 710-1652

2 784-5688

3 784-5687A

4 756-0625

5 738-0924

6 684-0030

7 741-0563

8 736-0105

9 712-0116

10 741-0598

11 736-0188

12 784-5689A

13 710-0538

14 736-0242

15 714-0474

16 736-0160

17 710-0788

18 784-5590

19 784-5638

20 710-0599

21 736-0351

DESCRIPTION

Hex Screw

Drive Cable Guide Bracket

Auger Clutch Cable Bracket

Roller Cable

Hex Screw 1/4-28

Frame Assembly

Ball Bearing

Bell Washer

Lock Jam Nut

Hex Flange Bearing

Flat Washer

Front Support Guide Bracket

Lock Hex Screw

Bell Washer .340 ID x .872 OD

Cotter Pin

Flat Washer .536 ID x .930 OD

Hex Washer Screw 1/4-20

Frame Shift Bracket

Frame Cover

Hex Washer Screw 1/4-20

Flat Washer .760 ID x .50 OD

REF.

PART

NO.

22 717-1445

23 714-0126

24 717-1444

25 715-0249

26 714-0143

27 684-0042B

28 656-0012A

29 684-0013B

30 746-0897

31 748-0190

32 684-0021

33 732-0264

34 712-0711

35 746-0898

36 738-0869

738-0830

37 784-5617A

38 735-0243

39 718-0301A

40 618-0063

Gear

Key

7-Tooth Shaft

DESCRIPTION

Roll Pin

Klik Pin

Friction Wheel Assembly

Friction Disc Wheel

Wheel Shift Rod Assembly

Drive Cable

Spacer

Friction Wheel Bracket Assembly

Extension Spring

Jam Nut 3/8-24

Drive Cable

Axle 13” Wheels

Axle 16” Wheels

Friction Plate

Friction Wheel Rubber

Friction Wheel Hub

Friction Wheel Bearing

SIZE

13 x 4

13 x 5

16 x 6.5

16.5 x 4.8

REF. NO. 1

WHEEL ASS’Y

COMPLETE

634-0114

734-1714

734-1712

734-1709

Wheel Assembly

REF. NO. 2

TIRE

REF. NO. 3

AIR

ONLY

734-1732

734-1527

734-1525

734-1530

VALVE

734-0255

REF. NO. 4

RIM

ONLY

734-1713

734-1711

734-1708

REF. NO. 5

SLEEVE

BEARING (2)

741-0401

REF. NO 6

Klik Pin

714-0143

Engine and V-Belts

E602E, 614E

IMPORTANT: For a proper working machine, use Factory

Approved Parts.

V-BELTS are specially designed to engage and disengage safely. A substitute (non OEM) V-Belt can be dangerous by not disengaging completely.

REF.

NO.

PART

NO.

1 710-1652

2 731-1324

3 732-0339

4 710-0627

5 710-3005

6 05896A

7 748-0234

8 756-0985

9 754-0343

10 756-0984

11 736-0270

12 710-0230

13 756-0313

14 710-1245

DESCRIPTION

Hex Washer Screw 1/4-20 x.5

Belt Cover

Extension Spring

Hex Screw 5/16-24 x .75

Hex Cap Screw 3/8-16 x 1.25

Drive Clutch Bracket

Shoulder Spacer

Pulley Half

V-Belt

Pulley Half

Bell Washer

Hex Cap Screw 1/4-28 x .50

Flat Idler

Lock Cap Screw 5/16-24

REF.

NO.

PART

NO.

712-0181

16 756-0569

17 736-0242

18 736-0505

19 736-0507

20 754-0430A

21 756-0967

22 736-0247

23 736-0331

DESCRIPTION

Lock Jam Nut 3/8-16

Pulley Half

Bell Washer

Flat Washer

Washer

Belt

Auger Pulley

Flat Washer

Bell Washer

24 710-0696

25 748-0360

26 710-0654A

Hex Cap Screw 3/8-24

Pulley

Hex Washer Screw 3/8-16 x 1.0

27 629-0071 Extension Cord

OEM-390-986 Electric Start Kit

Engine and V-Belts

E642E, E642F, E662E, E662H, 614E, E644E, E664F AND E6A4E

IMPORTANT: For a proper working machine, use Factory

Approved Parts.

V-BELTS are specially designed to engage and disengage safely. A substitute (non OEM) V-Belt can be dangerous by not disengaging completely.

REF.

PART

NO.

1 710-1652

2 731-1324

3 710-3005

4 732-0710

5 710-0627

6 05896A

7 748-0234

8 756-0987

9 754-0346

10 756-0986

11 736-0270

12 710-0230

13 756-0313

DESCRIPTION

Hex Washer Screw 1/4-20 x .50

Belt Cover

Hex Cap Screw 3/8-16 x 1.25

Spring Extension

Hex Screw 5/16-24 x .75

Drive Clutch Idler Bracket

Shoulder Spacer

Pulley Half

Belt

Pulley Half

Bell Washer

Hex Cap Screw

Flat Idler

REF.

NO.

PART

NO.

712-0181

15 710-0654A

16 710-1245

17 736-0242

18 736-0505

19 756-0967

20 756-0569

21 754-0430A

22 736-0247

DESCRIPTION

Lock Jam Nut 3/8-16

Hex Washer Screw 3/8-16 x 1.0

Hex Lock Screw 5/16-24 x .875

Bell Washer .340 ID x .872 OD

Flat Washer .341 ID x .50 OD

Pulley Auger

Pulley Half

V-Belt

Flat Washer

23 736-0331

24 710-0696

25 748-0360

Bell Washer .39 ID x 1.13 OD

Hex Cap Screw 3/8-24 x .875

Pulley Adapter

26 OEM-390-987 Electric Start

MANUFACTURER’S LIMITED WARRANTY FOR:

The limited warranty set forth below is given by MTD

PRODUCTS INC (“MTD”) with respect to new merchandise purchased and used in the United States, its possessions and territories.

MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment not approved by MTD Products Inc. for use with the product(s) covered by this manual will void your warranty as to any resulting damages.

Normal wear parts or components thereof are subject to separate terms as follows: All normal wear part or component failures will be covered on the product for a period of

90 days regardless of cause. After 90 days, but within the two year period, normal wear part failures will be covered

ONLY IF caused by defects in material or workmanship of

OTHER component parts. Normal wear parts and components include, but are not limited to, belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow thrower skid shoes, shave plates and tires. Batteries are covered by a 90-day limited replacement warranty.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH YOUR

LOCAL AUTHORIZED SERVICE DEALER. To locate the dealer in your area, please check for a listing in the Yellow

Pages or contact the Customer Service Department of

MTD PRODUCTS INC by calling 1-800-800-7310 or writing to P.O. Box 368022, Cleveland, Ohio 44136-9722. No product returned directly to the factory will be accepted unless prior written permission has been extended by the

Customer Service Department of MTD PRODUCTS INC.

This limited warranty does not provide coverage in the following cases:

a. The engine or component parts thereof. These items carry a separate manufacturer’s warranty. Please refer to the applicable manufacturer’s warranty on these items.

b. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake adjustments, clutch adjustments or deck adjustments; and normal deterioration of the exterior finish due to use or exposure.

c. Log splitter pumps, valves and cylinders have a separate one year warranty.

d. MTD does not extend any warranty for products sold or exported outside of the United States of America, its possessions and territories, except those sold through MTD’s authorized channels of export distribution.

No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product shall bind MTD. During the period of the Warranty, the exclusive remedy is repair or replacement of

the product as set forth above. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted

product. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased as a gift.

How State Law Relates to this Warranty: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Živjo! Sem AI chatbot, posebej usposobljen za pomoč pri YARD MACHINES 614 E. Temeljito sem pregledal dokument in vam lahko pomagam najti točne informacije, ki jih potrebujete, ali razložim vsebino na jasen in preprost način. Ne glede na to, ali iščete navodila o določenih funkcijah, korake za odpravljanje težav ali splošno uporabo, lahko zastavite svoja vprašanja. Več podrobnosti kot navedete o svojih pomislekih ali potrebah, natančneje in učinkoviteje vam lahko pomagam!

Pomočnik tipka

Pomočnik je prekinil povezavo. Poskusite znova pozneje.

Izgleda, da ste prišli do dokumenta, ki je napisan v več jezikih, vključno z jezikom, ki ni vaš materni jezik. Uporabite lahko naslednje povezave, da začasno skrijete strani brez jezika, ki ga želite.

Oglas