STMicroelectronics SR2 Datasheet

SR2
6 pin Smart Reset™
Datasheet - production data
Applications
 Wearable
 Activity tracker
 Smartwatch
 Smartglasses
UDFN6 (1.6 x 1.3 mm)
Features
 Operating voltage 1.65 V to 5.5 V
 Low supply current 1.5 µA
 Integrated test mode
 Dual Smart Reset™ push-button inputs with
fixed extended reset setup delay (tSRC) from
0.5 s to 10 s in 0.5 s steps (typ.), option with
internal pull-up resistor
 Push-button controlled reset pulse duration
– Option 1: fully push-button controlled, no
fixed or minimum pulse width guaranteed
– Option 2: defined output reset pulse
duration (tREC), factory-programmed
 No power-on reset
 Single reset output
– Active low or active high
– Push-pull or open drain with optional pullup resistor
 Fixed Smart Reset™ input logic voltage levels
 Operating temperature: - 40 °C to +85 °C
 UDFN6 package: 1.6 mm x 1.3 mm
 ECOPACK®2 (RoHS compliant, HalogenFree)
May 2014
This is information on a product in full production.
DocID026047 Rev 2
1/22
www.st.com
Contents
SR2
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
2
Test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1
Power supply (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2
Ground (VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3
Smart Reset™ input (SR0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4
Smart Reset™ input (SR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5
Reset output (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Typical application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Timing waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5
Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10
Package marking information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2/22
DocID026047 Rev 2
SR2
1
Description
Description
The Smart Reset™ devices provide a useful feature that ensures inadvertent short reset
push-button closures do not cause system resets. This is done by implementing extended
Smart Reset™ input delay time (tSRC) and combined push-button inputs, which together
ensures a safe reset and eliminates the need for a specific dedicated reset button.
This reset configuration provides versatility and allows the application to distinguish
between a software generated interrupt and a hard system reset. When the input pushbutton are connected to microcontroller interrupt inputs, and are closed for a short time, the
processor can only be interrupted. If the system still does not respond properly, continuing
to keep the push-button closed for the extended setup time tSRC causes a hard reset of the
processor through the reset output.
The SR2 has two combined delayed Smart Reset™ inputs (SR0, SR1) with preset delayed
Smart Reset™ setup time (tSRC). The reset output is asserted after both of the Smart
Reset™ inputs were held active for the selected tSRC delay time. Depending on selected
option the RST output remains asserted either until at least one SR input goes to inactive
logic level (i.e. neither fixed nor minimum reset pulse width is set) or the output reset pulse
duration is fixed for tREC (i.e. factory-programmed). The reset output, RST, is active low or
active high, push-pull or open drain with optional pull-up resistor. The device fully operates
over a broad VCC range 1.65 V to 5.5 V. Below 1.575 V typ. the inputs are ignored and
outputs are deasserted; the deasserted reset output levels are then valid down to 1.0 V.
1.1
Test mode
After pull of SR0 up to VTEST or more (VCC + 1.4 V, max.) we start counting initial shorten
tSRC-INI (42 ms, typ.). After tSRC-INI expires, the RST output either goes down for tREC (if
tREC option is used) or stays low as long as overvoltage on SR0 in detected (if tREC option is
not used). This is a feedback and a user knows that the device is locked in the test mode.
Each time both SR inputs are connected to ground in test mode a shorten tSRC-SHORT (21
ms, typ.) is used instead of long tSRC (0.5 s -10 s). Return from to normal mode is possible
by a new startup of the device (i.e. VCC goes to 0 V and back to its original state). In this way
the device can be quickly tested without repeating test mode triggering. Advantage of this
solution is pretty high glitch immunity, feedback to user about entry to the test mode and
testability within full VCC range.
DocID026047 Rev 2
3/22
22
Description
SR2
Figure 1. Logic diagram
VCC
SR 0
SR2
RST
SR1
GND
GAMS2602141440SG
Figure 2. Pin connections (top view)
VSS
1
SR 1
2
RST
3
SR2
6
V CC
5
SR 0
4
NC
GAMS2602141445SG
4/22
DocID026047 Rev 2
SR2
Description
Table 1. Signal names
Pin Name
1
VSS
2
SR1
Type
Description
Supply ground Ground
Input
3
RST
Output
4
NC
-
5
SR0
Input
6
VCC
Secondary push-button Smart Reset™ input. Active low. Optional pull-up resistor
Reset output
(open drain with optional pull-up resistor, active low)
(push-pull – active low or active high)
Not connected (not bonded; should be connected to VSS)
Primary push-button Smart Reset™ input. Active low. Optional pull-up resistor
Positive supply voltage for the device. A 0.1 µF decoupling ceramic capacitor is
Supply voltage recommended to be connected between VCC and VSS pins, as close to the SR2
device as possible
Figure 3. Block diagram
2YHUYROWDJHGHWHFW
WHVWPRGHWULJJHU
65 65
$1'
W 65&
JHQHUDWRU
W5(&
JHQHUDWRU
RSWLRQDO
567
$09
DocID026047 Rev 2
5/22
22
Pin descriptions
SR2
2
Pin descriptions
2.1
Power supply (VCC)
This pin is used to provide power to the Smart Reset™ device. A 0.1 µF ceramic decoupling
capacitor is recommended to be connected between the VCC and VSS pins, as close to the
SR2 device as possible.
2.2
Ground (VSS)
Ground pin for the device.
2.3
Smart Reset™ input (SR0)
Push-button Smart Reset™ input is active low with optional pull-up resistor. Both SR
inputs need to be asserted simultaneously for at least tSRC to assert the reset output (RST).
By connecting a voltage higher than VCC to the SR0 the device enters a test mode (see
Section 1: Description on page 3 for more information).
2.4
Smart Reset™ input (SR1)
Push-button Smart Reset™ input is active low with optional pull-up resistor. Both SR inputs
need to be asserted simultaneously for at least tSRC to assert the reset output (RST).
2.5
Reset output (RST)
RST is active low or active high, push-pull or open drain reset output with optional internal
pull-up resistor. Output reset pulse width is optional as follows:

Neither fixed nor minimum output reset pulse duration (releasing the push-button while
reset output is active, causes the output to deassert);

Fixed, factory-programmed output reset pulse duration for tREC independent on Smart
Reset™ input state.
If VCC drops below 1.575 V, the RST output is deasserted and its state is guaranteed down
to 1 V (see Figure 8).
6/22
DocID026047 Rev 2
SR2
3
Typical application diagram
Typical application diagram
Figure 4. Single-button Smart Reset™ typical hookup
VCC
(1)
(2)
VCC
VCC
RST
RESET
SR2
MCU
SR0
SR1
INT / NMI
VSS
VSS
PUSH - BUTTON
SWITCH (3)
GAMS2602141450SG
1. External pull-up resistor requested if the reset output (RST) is open drain type without internal pull-up.
2. External pull-up resistor requested if the Smart Reset™ inputs (SR0 and SR1) have no internal pull-up.
3. When only one Smart Reset™ input push-button is used, tie both the SR inputs together.
DocID026047 Rev 2
7/22
22
Typical application diagram
SR2
Figure 5. Dual-button Smart Reset™ typical hookup
VCC
(1)
(2)
VCC
(2)
VCC
RST
RESET
MCU
SR2
SR0
SR1
INT/ NMI
VSS
VSS
PUSH -BUTTON
SWITCH
PUSH - BUTTON
SWITCH
GAMS2602141500SG
1. External pull-up resistor requested if the reset output (RST) is open drain type without internal pull-up.
2. External pull-up resistor requested if the Smart Reset™ inputs (SR0 and SR1) have no internal pull-up.
8/22
DocID026047 Rev 2
SR2
Timing waveforms
4
Timing waveforms
Figure 6. Option without tREC
9
9&&
9
9
9
6WDUW
WLPHU
(QG
WLPHU
3XVKEXWWRQ
FRQWUROOHGRXWSXW
W65&
65
*OLWFK
LPPXQLW\
65
567
$09
Figure 7. Option with tREC
9
9
9
9
9&&
W5(&
W65&
65
*OLWFK
LPPXQLW\
65
567
$09
DocID026047 Rev 2
9/22
22
Timing waveforms
SR2
Figure 8. Undervoltage condition
9
9&&
9
9
9
65
9
9
65
9
9
567
9
W65&
7LPHV
1. If undervoltage occurs (VCC drops below 1.575 V typ.) while reset output is active, the reset output is
released and goes inactive.
10/22
DocID026047 Rev 2
$0
SR2
Typical operating characteristics
Figure 9. Supply current (ICC) vs. temperature (TA)
6XSSO\FXUUHQW,&& —$
9&& 9
9&& 9
9&& 9
7HPSHUDWXUHƒ&
$09
Figure 10. Smart Reset™ delay (tSRC) vs. temperature (TA), tSRC = 7.5 s (typ.)
6PDUW5HVHW70GHOD\W 65& V
5
Typical operating characteristics
9&& 9
9&& 9
9&& 9
7HPSHUDWXUHƒ&
$09
DocID026047 Rev 2
11/22
22
Typical operating characteristics
SR2
Figure 11. Test mode entry voltage (VTEST) vs. temperature (TA)
7HVWPRGHHQWU\YROWDJH97(67 9
9&& 9
9&& 9
9&& 9
7HPSHUDWXUH7$ƒ&
$0
Figure 12. Initial test mode time (tSRC-INI) vs. temperature (TA)
,QLWLDOWHVWPRGHWLPHW65&B,1, PV
9&& 9
9&& 9
9&& 9
7HPSHUDWXUH7$ƒ&
12/22
DocID026047 Rev 2
$0
SR2
6
Maximum ratings
Maximum ratings
Stressing the device above the rating listed in Table 2: Absolute maximum ratings may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in Table 3: Operating and
measurement conditions of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability. Refer also to the
STMicroelectronics™ SURE program and other relevant quality documents.
Table 2. Absolute maximum ratings
Symbol
TSTG
TSLD(1)
Parameter
Storage temperature (VCC off)
Lead solder temperature for 10 seconds
VIO
Input or output voltage
VCC
Supply voltage
Value
Unit
-55 to +150
°C
260
°C
-0.3 to
5.5(2)
V
-0.3 to 7
V
ESD
VHBM
Electrostatic discharge protection, human body model (JESD22A114-B level 2)
2
kV
VRCDM
Electrostatic discharge protection, charged device model, all pins
1
kV
200
V
EIA/JESD78
-
VMM
Electrostatic discharge protection, machine model, all pins
(JESD22-A115-A level A)
Latch-up (VCC pin, SR0 reset input pin)
1. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds.
2. For push-pull RST output type only from -0.3 V to VCC +0.3 V.
DocID026047 Rev 2
13/22
22
DC and AC parameters
7
SR2
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC
characteristics of the device. The parameters inTable 4: DC and AC characteristic that
follow, are derived from tests performed under the measurement conditions summarized in
Table 3: Operating and measurement conditions. Designers should check that the operating
conditions in their circuit match the operating conditions when relying on the quoted
parameters.
Table 3. Operating and measurement conditions
Symbol
VCC
TA
14/22
Parameter
Value
Unit
Supply voltage
1.65 to 5.5
V
Ambient operating temperature
-40 to +85
°C
DocID026047 Rev 2
SR2
DC and AC parameters
Table 4. DC and AC characteristic
Symbol
Parameter
VCC
Supply voltage(3)
ICC
Supply current (inputs in
their inactive state, tSRC
counter is not running)
VOL
VOH
Reset output voltage low
Reset output voltage high
(push-pull output only)
Test conditions(1)
Typ.(2)
1.65
Max.
Unit
5.5
V
VCC = 3.0 V
1.1
2.5
µA
VCC = 5.0 V
1.5
3.0
µA
VCC  4.5 V, sinking 3.2 mA
0.3
V
VCC  3.3 V, sinking 2.5 mA
0.3
V
VCC  1.65 V, sinking 1 mA
0.3
V
VCC  4.5 V, ISOURCE = 0.8 mA
0.8 VCC
V
VCC  2.7 V, ISOURCE = 0.5 mA
0.8 VCC
V
VCC  1.65 V, ISOURCE = 0.25 mA
0.8 VCC
V
Reset timeout delay,
factory-programmed
(device option)
RPUO
Internal output pull-up
resistor on RST
(device option)
ILO
Output leakage current
VRST = 5.5 V, open drain device
option without output pull-up
resistor
tREC
Min.
240
360
480
65
-0.1
ms
k
0.1
µA
Smart ResetTM
tSRC
Smart Reset™ delay
TA = -40 to +85 °C
0.8 x tSRC
TA = 25 °C
0.9 x tSRC
tSRC(4)
1.2 x tSRC
s
1.1 x tSRC
VIL
SR0, SR1 input voltage
low
VSS -0.3
0.3
V
VIH
SR0, SR1 input voltage
high
0.85
5.5
V
ILI
SR0, SR1 input leakage
current
-0.1
0.1
µA
Input glitch immunity(5)
SR0 and SR1 asserted
tSRC
s
Test mode
VTEST
Test mode entry voltage
tSRC-INI Initial test mode time
tSRCSHORT
Shorten Smart Reset™
delay
VCC +0.9
VCC +1.1
VCC +1.4
V
28
42
56
ms
16.8
21
25.2
ms
1. Valid for ambient operating temperature TA = -40 to +85 °C, VCC = 1.65 to 5.5 V.
2. Typical values are at 25 °C and VCC = 3.3 V unless otherwise noted.
3. Reset outputs are deasserted below 1.575 V typ. and remain deasserted down to VCC = 1 V.
4. Factory-programmable in the range of 0.5 s to 10 s typ. in 0.5 s steps (see Table 7 for available delays).
5.
Input glitch immunity is equal to tSRC, when both inputs (SR0 and SR1) are low. Otherwise infinite.
DocID026047 Rev 2
15/22
22
Package information
8
SR2
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 13. Package outline for UDFN6 1.6 x 1.3 x 0.55 mm, 0.40 mm pitch
'
$
%
3,1,1'(;$5($
'[(
(
& [
& [
7239,(:
&
&
$
[
6($7,1*
3/$1(
6,'(9,(:
&
$
H
E[
3,1,1'(;$5($
'[(
& $ %
&
/[
%277209,(:
$0
16/22
DocID026047 Rev 2
SR2
Package information
Table 5. Mechanical data for UDFN6 1.6 x 1.3 x 0.55 mm, 0.40 mm pitch
Dimensions
Symbol
Drawing (millimeters)
Drawing (inches)
Note
Min.
Typ.
Max.
Min.
Typ.
Max.
A
0.50
0.55
0.60
0.020
0.022
0.024
A1
0.00
0.02
0.05
0.0000
0.0008
0.0020
b
0.15
0.20
0.25
0.006
0.008
0.010
D
1.30 BSC
0.051 BSC
E
1.60 BSC
0.063 BSC
e
0.40 BSC
0.016 BSC
L
0.250
N
0.325
0.400
0.0098
6
0.0128
0.0157
6
Figure 14. Footprint recommendation for UDFN6 1.6 x 1.3 x 0.55 mm, 0.40 mm pitch
$0
DocID026047 Rev 2
17/22
22
Package information
SR2
Figure 15. Carrier tape for UDFN6 1.6 x 1.3 x 0.55 mm
3
“
7
“
3R
“
(
“
<
'
‘“
&/
)
:
5()
ƒ
%R
<
3
$R
.R
6(&7,21<<
$R
%R
.R
)
3
:
“
“
“
“
“
“
$0
1. Measured from centreline of sprocket hole to centreline of pocket.
2. Cumulative tolerance of 10 sprocket holes is ± 0.20.
3. Measured from centreline of sprocket hole to centreline of pocket.
4. Other material available.
5. Typical SR of formed tape max. 109 SQ.
6. All dimensions in millimeters unless otherwise stated.
Figure 16. Pin 1 orientation
8VHUGLUHFWLRQRIIHHG
$0
18/22
DocID026047 Rev 2
SR2
9
Part numbering
Part numbering
Table 6. Ordering information scheme
Example:
SR2
H
A
R
U
Device type
SR2
Smart Reset™ set up delay (tSRC)(1)
H = factory programmable tSRC = 4.0 s, no pull-up
L = factory programmable tSRC = 6.0 s, no pull-up
P = factory programmable tSRC = 7.5 s, no pull-up
U = factory programmable tSRC = 10.0 s, no pull-up
Outputs type
A = open drain, no pull-up, active low
Reset timeout period (tREC)
B = factory programmable tREC = 360 ms (typ.)
R = push-button controlled
Package
DL = UDFN6
1. Smart ResetTM delay (tSRC) is available from 0.5 s to 10 s in 0.5 s steps (typ.). Minimum order quantities
may apply. Contact local sales office for availability.
DocID026047 Rev 2
19/22
22
Package marking information
10
SR2
Package marking information
Table 7. Package marking
tSRC (s)
Smart Reset™
inputs(1)
Output
type(2)
tREC option
(ms)(3)
SR2HARU
4.0
AL
OD, AL
No tREC
UDFN6
HA
SR2LABU
6.0
AL
OD, AL
360
UDFN6
LC
SR2LARU
6.0
AL
OD, AL
No tREC
UDFN6
LA
SR2PARU
7.5
AL
OD, AL
No tREC
UDFN6
PA
SR2UABU
10.0
AL
OD, AL
360
UDFN6
UC
SR2UARU
10.0
AL
OD, AL
No tREC
UDFN6
UA
Part number
Package Topmark
1. AL = active low.
2. OD = open drain, AL = active low.
3. No tREC = push-button controlled reset pulse width.
Figure 17. Package marking (top view)
$
%
$ GRWSLQUHIHUHQFH
% PDUNLQJDUHDWRSPDUN
$0
20/22
DocID026047 Rev 2
SR2
11
Revision history
Revision history
Table 8. Document revision history
Date
Revision
Changes
10-Mar-2014
1
Initial release
13-May-2014
2
Modified: tREC values Table 4 on page 15
Updated: Table 6 on page 19
DocID026047 Rev 2
21/22
22
SR2
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
22/22
DocID026047 Rev 2
">