Mitel Superset 1000 Owner's Manual

Owner’s Manual

Table of Contents

1

Introduction............................................................................5

Conformance ........................................................................5

Important Safety instructions ................................................5

FCC Regulatory Information.................................................7

Industry Canada Regulatory Information .............................9

Radio Interference ..............................................................10

RF Radiation Exposure ......................................................10

Basic Requirements............................................................10

Using this Document...........................................................11

2

Getting to know your Mitel 1000.........................................12

Parts Check.........................................................................12

Front Panel..........................................................................13

3

Connecting your Mitel 1000................................................14

Digital Cordless phone range .............................................14

Connecting CO lines...........................................................14

Connecting your ADSL line ................................................14

Connecting the Power ........................................................15

Register your Cordless phones..........................................15

Connecting to the Internet ..................................................15

Cabling Featurephone ........................................................16

Cabling Standard telephones.............................................16

Wall Mounting the Mitel 1000 .............................................17

Featurephone connections (underside of phone)..............17

Featurephone connections (underside of phone)..............18

Attaching the Featurephone desk plinth ............................19

Wall-mounting a Featurephone..........................................19

Doorphone ..........................................................................20

Power Fail Telephone.........................................................21

2

4

Basic programming using the Management

Application .......................................................................22

Basic PABX Settings ..........................................................24

Date & Time Settings..........................................................30

5

Using Your Mitel 1000 Phone System ...............................31

System Description.............................................................31

Introduction to your Mitel 1000 Phones .............................31

System Featurephone ........................................................33

Using the Cordless Telephone...........................................38

Featurephone– Basic Call Features ..................................41

Using a Standard or cordless Telephone ..........................49

Additional Call Features......................................................53

Extension Set-Up options...................................................59

Incoming Call Handling.......................................................61

Using Voicemail ..................................................................62

Remote Notification of Voice Messages ............................65

Programming Additional System Options..........................69

6

Connecting to the Internet ..................................................70

ADSL Modem configuration ...............................................70

Types of Internet Access ....................................................70

Configuring a PPPoA ADSL connection............................70

Configuring a PPPoE ADSL connection............................73

Configuring a DHCP ADSL connection – RFC

1483 .................................................................................76

ADSL Operating Mode ......................................................80

Connecting to an External ADSL Modem, Cable

Modem, LAN, WAN or add a host to the DMZ...............81

Password.............................................................................86

DHCP Server ......................................................................88

Addressing ..........................................................................92

Changing the LAN IP address and subnet mask ..............92

Incoming Ringing ................................................................94

System Settings ..................................................................96

3

B

C

D

E

F

A

Extension Settings ............................................................100

Line Settings......................................................................107

Line Forwarding ................................................................108

Class of Service ................................................................109

Timers................................................................................111

LCR Programming............................................................112

CLI Routes ........................................................................113

Outgoing Restriction .........................................................114

VoIP Settings ....................................................................119

Wireless Setup / Security..................................................122

Firewall ..............................................................................135

Diagnostics........................................................................148

Firmware Update ..............................................................154

System Resets..................................................................157

Configuring Your Mitel 1000 via the Featurephone.........159

To enter system programming .........................................159

System Setup Options......................................................159

Using Voicemail ................................................................171

Programming Additional System Options........................176

Miscellaneous system configuration options ...................177

To configure CO lines .......................................................180

To set system timers.........................................................182

To reset your system ........................................................183

Cordless Phone Detailed Instructions..............................184

IP Addresses, Network Masks & Subnets .......................193

IP Addresses.....................................................................193

Subnet masks ...................................................................194

Glossary ............................................................................195

Configuring your PCs........................................................201

Configuring Ethernet PCs.................................................201

Troubleshooting ................................................................206

Cannot browse the Internet ..............................................206

Troubleshooting your Cordless Phone.............................210

Troubleshooting the PABX ...............................................211

4

1

Introduction

Congratulations on becoming the owner of the Mitel 1000 combined voice & data communications system. You will now be able to access the Internet using your high-speed DSL connection, share your phone connection between fixed & cordless handsets and access the latest in ‘Voice over IP’ services.

This User Guide will show you how to connect Mitel 1000 and how to customize its configuration to get the most out of your new product.

Conformance

This equipment is designed for use in the United States and

Canada.

This equipment complies with the following standards:

FCC Part 15, Subparts B, C, D

Industry Canada RSS-213, RSS-210, CS-03

FCC Part 68

UL60950-1/CSA C22.2 No. 60950-1

Analog extension ports: TNV3

CO port: TNV3

ADSL port: TNV3

Power fail port TNV3

LAN/WAN ports SELV

Doorstrike Port SELV

Important Safety instructions

The following safety information is reprinted from IEC60950.

• When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read and understand all instructions.

• Follow all warnings and instructions marked on the product.

• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

• Do not use this product near water (for example, in a wet basement).

• Do not place this product on an unstable cart, stand, or table.

The product can fall, causing serious damage to the product.

• Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from overheating; these openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.

5

• This product should be operated only from the type of power source indicated in the manual. If you are not sure of the type of power source to your building, consult your dealer or local

Power Company.

• The mains power socket outlet must be located near the product and must be easily accessible to allow plugging/unplugging.

• Do not allow anything to rest on the power cord. Do not locate this product where persons walking on it will abuse the cord.

• Do not use an extension cord with this product’s AC power cord. The AC outlet for this product should not be used for any other electrical equipment.

• Never push objects of any kind into this product through cabinet slots as they can touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

• To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified serviceman when some service or repair work is required. Opening or removing covers can expose you to dangerous voltages or other risks. Incorrect re-assembly can cause electric shock when the product is subsequently used.

• Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

- When the power supply cord or plug is damaged or frayed.

- If liquid has been spilled into the product.

- If the product has been exposed to rain or water.

- If the product does not operate normally by following the operating instructions.

- Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls can result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been damaged.

- If the product exhibits a distinct change in performance.

• Avoid using a telephone (other than a cordless type) during an electrical storm. There can be a remote risk of electric shock from lightning.

• Do not use the telephone to report a gas leak in the vicinity of the leak.

Save These Instructions.

CAUTION

Use only 26 AWG line cord or larger for

Central Office line connections.

6

FCC Regulatory Information

This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA.

On the exterior of the cabinet of this equipment is a label that contains, among other information, a product identifier in the format

US:LKCMF01BSIGMA

If requested, this number must be provided to the telephone company.

• FCC Registration Number: LKCMF01BSIGMA

• Ringer Equivalence Number (REN): 0.1B

• Facility Interface Code (FIC): 02LS2

• Service Order Code (SOC): 9.0Y

• USOC Jack Type: RJ11C

A FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant. See Installation Instructions for details.

The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. Typically, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line (as determined by the total RENs) contact the local Telephone

Company.

If this system causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the

Telephone Company will notify the customer as soon as possible.

Also, you will be advised of your right to file a complaint with the

FCC if you believe it is necessary.

The Telephone Company may make changes to it's facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice so you can make the necessary modifications to maintain uninterrupted service.

If the equipment is causing harm to the telephone network, the

Telephone Company may request that you disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.)

This equipment is hearing aid compatible.

Customer Owned Coin/Credit Card Phones

To comply with state tariffs, the Telephone Company must be given notification prior to connection. In some states, the state public utility commission, public service commission or corporation commission must give prior approval of connection.

Data Equipment

The table below shows which jacks are associated with which modes of operation:

7

Mode of Operation

Permissive

USOC Jack

RJ11C

Systems

Facility Interface Codes (FIC), Service Order Codes (SOC), USOC

Jack Codes and Ringer Equivalence Numbers (REN) are shown in the table below for each port where applicable:

Port FIC SOC

Line 1 02LS2 9.0Y

Line 2 02LS2 9.0Y

ADSL 02LS2 9.0Y

Automatic Dialers

USOC

RJ11C

RJ11C

RJ11C

REN

0.1B

0.1B

0.1B

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR)

MAKING TEST CALLS TO EMERGENCY NUMBERS:

1. Remain on the line and briefly explain to the dispatcher the reason for the call.

2. Perform such activities in the off-peak hours, such as early morning or late evenings.

Toll Restriction and Least Cost Routing Equipment

The software contained in Mitel 1000 to allow user access to the network must be upgraded to recognize newly established network area codes and exchange codes as they are placed into service.

Failure to upgrade the premises systems or peripheral equipment to recognize the new codes as they are established will restrict the customer and the customer's employees from gaining access to the network and to these codes.

Equipment with Direct Inward Dialing (DID)

ALLOWING THIS EQUIPMENT TO BE OPERATED IN SUCH A

MANNER AS TO NOT PROVIDE FOR PROPER ANSWER

SUPERVISION IS A VIOLATION OF PART 68 OF THE FCC'S

RULES

PROPER ANSWER SUPERVISION IS WHEN:

A. This equipment returns answer supervision to the PSTN when

DID calls are:

• Answered by the called station

• Answered by the attendant

• Routed to a recorded announcement that can be administered by the CPE user.

• Routed to a dial prompt

B. This equipment returns answer supervision on all DID calls forwarded to the PSTN.

Permissible exceptions are:

• A call is unanswered

• A busy tone is received

• A reorder tone is received

Equal Access Requirements

This equipment is capable of providing users access to interstate providers of operator services through the use of access codes.

Modification of this equipment by call aggregators to block access dialing codes is a violation of the Telephone Operator Consumers

Act of 1990.

8

Electrical Safety Advisory

It is strongly suggested that an AC surge arrestor be installed in the

AC outlet to which this equipment is connected.

Modifications

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. There are no user-serviceable parts or adjustments inside this equipment - please do not open the equipment case.

Industry Canada Regulatory Information

This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques applicables d’Industrie Canada.

NOTICE: This equipment meets the applicable Industry Canada

Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry

Canada technical specifications were met.It does not imply that

Industry Canada approved the equipment.

AVIS : Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal.

Cette conformité est confirmée par le numéro d'enregistrement. Le sigle IC, placé devant le numéro d'enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d'Industrie

Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the

Ringer Equivalence Numbers of all the devices does not exceed five.

AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L'IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d'une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas

5.

Privacy on DECT Handsets

Privacy of communications may not be ensured when using DECT telephones with this product.

9

Radio Interference

This device complies with Part 15 of the FCC Rules and RSS-213 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and RSS-213 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

RF Radiation Exposure

This equipment complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 8 inches (20 centimeters) between the radiator and your body.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Basic Requirements

In order to use all the features of the Mitel 1000 system, you must have the following:

DSL service up and running on your telephone line (or an equivalent broadband Internet access).

Instructions from your ISP on what type of Internet access you will be using, and the addresses needed to set up access.

Instructions from your ISP on the settings required to configure your

Voice over IP (VoIP) service.

One or more computers each containing an ethernet card (10Base-

T/100Base-T network interface card (NIC)).

For system configuration using the supplied web-based program: a web browser such as Internet Explorer v4 or later, or Netscape v4 or later. Note that version 4 of each browser is the minimum version requirement – for optimum display quality, use Internet Explorer v5, or Netscape v6.1.

10

Note

You do not need to use a hub or switch in order to connect more than one Ethernet PC to your Mitel 1000. Instead, you can connect up to four Ethernet PCs directly to your Mitel 1000 using the ports labeled on the rear panel.

Using this Document

Notational conventions

Acronyms are defined the first time they appear in the text and also in the glossary.

The term LAN refers to a group of Ethernet-connected computers at one site.

The term WLAN refers to a group of Wireless-connected computers at one site.

Typographical conventions

Italic text is used for items you select from menus and drop-down lists and the names of displayed web pages.

Bold text is used for text strings that you type when prompted by the program, and to emphasize important points.

Special messages

This document uses the following icons to draw your attention to specific instructions or explanations.

Provides clarifying or non-essential information on the current topic.

Note

Definition

Explains terms or acronyms that may be unfamiliar to many readers. These terms are also included in the Glossary.

WARNING

Provides messages of high importance, including messages relating to personal safety or system integrity.

11

2

Getting to know your Mitel 1000

Parts Check

In addition to this document on CD, your package should arrive containing the following:

1 Mitel 1000 Unit

1 Power Supply Mitel 1000

(PSU)

1 Blue (Ethernet WAN) cable

RJ-45

1 Documentation Pack 1 Cordless handset & charger

1 Yellow (Ethernet LAN) cable RJ-45

2 Grey line cables

1 Main distributor frame cover

(MDF)

1 Violet ADSL cable

(RJ-11 to RJ-11)

12

Front Panel

The front panel contains a ‘Page’ button and lights called Light

Emitting Diodes (LEDs) that indicate the status of the Mitel 1000.

Pressing the ‘Page’ button rings all the cordless handsets registered to the Mitel 1000.

Label Color

Power Off

Function

Power not connected to the Mitel 1000

Red

Flashing

Red/Green

Powering up or Mitel 1000 malfunction

Cordless phone registration mode

Green

Ethernet Off

No Mitel 1000 connected to the LAN

Powered Mitel 1000 connected to the

LAN

DSL Off

Green flashing

ADSL line not connected

ADSL line Connected and synchronizing

ADSL line connected and synchronized Green.

(Occasional flicker)

Internet Off

Red

ADSL line not connected

Mitel 1000 attempted to make an IP connection and failed. Usually indicates that the Internet User Name or

Password is incorrect.

Flashing

Green is detected

Mitel 1000 is IP connected and traffic is detected

Wireless Off

Flashing

Green

Wireless LAN is disabled

Green

Wireless LAN is enabled

Wireless LAN is active with traffic in either direction

13

3

Connecting your Mitel 1000

These instructions are a guide to the installation and basic configuration of the Mitel 1000.

When selecting the location for the system the range of the cordless handsets should be considered to ensure you have satisfactory coverage.

Digital Cordless phone range

The Digital Cordless phones have a range of 650ft outdoors when there is a clear line of sight between the Mitel 1000 and the handset. When there is no clear line of sight between the handset and the system, e.g. the system is indoors and the handsets is either indoors or outdoors, the range could be reduced to 160ft.

Thick stone walls will severely affect the range.

The symbol on your handset indicates when you are in range.

If you move too far away from the Mitel 1000 during a call your phone will sound an alert tone and will flash.

Connecting CO lines

If your system is supplied with a Featurephone, please connect this directly to extension 20 otherwise connect a standard analog phone. If you wish to relocate the phone this should be done later.

Plug line (s) cable (gray) into the line socket(s) on the back of the unit.

Connecting your ADSL line

If your Internet access is supplied over an ADSL line, plug the ADSL cable (purple) into the ADSL socket on the back of the unit. (Marked in purple)

14

Plug the CO line into the phone connector and the DSL cable into the DSL connector on the splitter and plug the splitter to the wall telephone outlet.

Connecting the Power

Connect the power supply between the unit and mains power outlet.

After approximately one minute, you will be able to make telephone calls.

Register your Cordless phones

• Press the ‘Page’ button for 4 seconds. This button is located on the front of the unit. This places the system in registration mode for 30 seconds.

• Select ‘REG’ on the Cordless phone.

• Press OK for ‘REGISTER’

• Enter 1234 as the PIN.

• The phone will register to the unit as Handset 1 (extension number 31).

• You can register more than one handset in the 30 seconds that the system is in registration mode. The sets are automatically allocated a handset number (1-6) and use extension numbers (31-34).

Connecting to the Internet

Connect the LAN Cable (yellow) from the LAN port of your PC to any of the ETHERNET sockets of your Mitel 1000 (yellow).

15

Program as an IP Gateway see page 83.

Cabling Featurephone

The Featurephone can be connected directly to the system using the telephone cord. If you wish to locate the phone further away from the Mitel 1000 you can do so by running telephone cable and using telephone sockets.

Four wires are needed to connect the Feature phones

Socket Pin Out Function RJ11 Pin Out

Cabling Standard telephones

Standard telephones can be connected directly to the system using the telephone cord. If you wish to locate the phone further away from the Mitel 1000 you can do so by running telephone cable and using telephone sockets. It is recommended that two pair cable is used with the same connections as for a Featurephone. You can however use a single pair.

Socket Pin Out Function RJ11 Pin Out

16

Wall Mounting the Mitel 1000

The Mitel 1000 can be wall mounted. You can print this page and use it as a template for locating the wall mounting screws supplied

1 to 1 Template (Letter size paper )

17

Featurephone connections (underside of phone)

Handset connector

Line cord connector

Data Port

Headset Port

18

Attaching the Featurephone desk plinth

The desk plinth allows you to mount the Featurephone at two angles.

Wall mount Plinth position

Plinth position 35

°

Plinth position 20

°

Wall-mounting a Featurephone

The phone plinth is inverted on the base to wall mount the phone.

Locate, drill and plug the 2 screw locations as shown below. The holes should be deep enough to accept a 1-inch screw. Insert the two screws leaving sufficient space to clip the base over them.

Locate the phone and base over the screws.

19

Line cord rails

6 inches

Wall hook when the

Featurephone is in a 20 degrees or 35 degrees position

Wall hook when the

Featurephone is wall mounted.

Doorphone

The doorphone is connected to extension 23.

20

Connect the single pair from the doorphone to the AB connections on extension 23.

The system must be programmed to recognize the doorphone See page 176 for programming via a Featurephone and page 97 for configuration via the Web Management application.

Power Fail Telephone

Connect a standard analogue telephone to the Power Fail connector.

When the Mitel 1000 is switched off the CO line (Line 1) is switched through to this phone and you can make and receive calls on it until the power is restored.

21

4

Basic programming using the Management

Application

Note

The Mitel 1000 includes a series of Web management pages that provide an interface to the software installed on the Mitel 1000. It enables you to configure the Mitel 1000. You can access it through your web browser from any PC connected to the Mitel 1000 via the wired or wireless LAN.

By default the Wireless network card in the Mitel 1000 is disabled.

This is as a security measure to prevent unauthorized access to the Mitel 1000. To turn the Wireless network on, see Page 122.

Open a Web Browser such as Internet Explorer or similar on the PC.

Go to the Management Application of your Mitel 1000 by entering the following address into the web browser, http://192.168.1.1

The following Log In screen is displayed

22

Note

Enter your user name and password.

The first time you log into the program, use these defaults:

User Name:

Password:

admin admin

You can change the password at any time or you can configure your Mitel 1000 so that you do not need to enter a password. See

Password on page 86

OK. The Welcome page is displayed:

Note

If you receive an error message or the Welcome page is not displayed, see Configuring your PCs on page 201.

This is the first page displayed each time you log in to the Web

It provides links to the programming pages that are most commonly used.

This page contains links to the following pages:

23

• Basic PABX Settings. (The most common settings for the telephone system).

• Router Configuration (This is only required if you are using a

Cable modem or private network).

• Wireless Security / Setup. (To set up a wireless connection to your PC(s).

• Time and Date Settings (To set the Time and Date on the phone system).

Basic PABX Settings

From this page you can configure the most commonly used telephone system functions, which are:

• Incoming Ringing. Selecting the phones that ring for incoming calls.

• Extension Names. Programming extension names so that the names rather than extension numbers used on the

Featurephone.

• Outgoing Restriction. You can restrict extensions from making calls on particular lines.

• Extension Class of Service. Restricting phones from making particular types of call e.g. International calls

• Cordless phone Registration. The cordless phones must be registered on the system before they can be used to make telephone calls

• Line Forwarding. On Power up incoming calls are forwarded to the Answering Machine if they are not answered within 18 seconds. The forwarding set for each line can be changed or cancelled

Incoming Ringing

You can determine which phones ring for incoming calls. Calls on each line can be set to ring different phones. You can also have different phones ringing when the system is in night mode.

For example, in DAY mode, all calls on Line1 might ring all phones, but in NIGHT mode all calls on Line 1 might be set to only ring extension 20.

Also, in both DAY & NIGHT modes, all calls on IP Trunk 1 might be set to ring on extension 23 only.

To change the settings, select ON or OFF from the relevant drop down box for the Line/Extension configuration you require.

The default is that ALL lines ring ALL extensions in both Day and

Night Modes.

24

WARNING

The Apply button must be clicked before the page is exited for the changes to take effect. The settings will be lost if this is not done.

Note

To set Night mode see page 61.

Extension Names

The settings on this page have an effect on an extension by extension basis. Individual features can be set or unset for particular extensions on the system.

You may assign names to extensions. When an extension receives an internal call, its 'display' will show the calling extension name in the place of the calling extension number.

To set the extension name, left mouse click on the field and enter the name associated with the extension.

25

WARNING

A maximum of 10 characters per name can be entered.

Voicemail

Use this setting to turn ON/OFF individual voicemail boxes for each extension.

The Apply button must be clicked when the names are entered and voice mail selected. Do not select any of the other options on the page until the Apply has been clicked or the settings for the names and voice mail will be lost.

Extension Class of Service

The Class of Service feature allows the user to define barring settings for each extension connected to the system restricting that extension from making certain types of calls from the system.

26

WARNING

The following restrictions can be defined on a per extension basis:

• No Restrictions

• Restrict International

• Local Only

• Emergency Calls Only

• By default ALL extensions can dial ALL destinations.

The Apply button, at the end of the page, must be clicked before the page is exited or any other link is selected for the changes to take effect. The settings will be lost if this is not done.

Day and Night Mode

There are different settings for Day Mode and Night Mode.

To configure Day/Night mode see page 61

The Allowed and Restricted Codes

The Allowed & Restricted codes can be used to add greater flexibility to the allowed and restricted codes.

For example, if you wanted to restrict all International calls, except those to the UK (international code 01144...). In this case place the extension in Restrict International in the Class of Service settings, and then set Allowed Codes to ON for the extension in question.

In the International table enter 011 in Index 1 and in the Allowed

Codes list enter the dialing code for the UK (01144). These settings allow the caller to dial 01144 but restrict all other 011 codes.

Similarly if you want restrict particular numbers enter them in the

Restricted Codes list and set the Restricted Codes ON for the extension.

If ‘Emergency Only’ is set, Allowed and Restricted codes must be

OFF.

Note

27

Programming Class of Service Codes

The definition of what constitutes Restricted, Allowed, National &

International calls, is determined by the leading digits of the dialed number.

Thus, for example, numbers beginning with ‘011xx’ are International calls. Numbers beginning one ‘1xx’ are National calls.

The definition of Allowed and Restricted codes is at the user’s discretion.

50 entries can be configured in the dialing codes for International,

National, Allowed & Restricted numbers.

These dialing rules can be configured manually. See ‘To change the

Allowed, Restricted, National and International codes, click here’ on the ‘Edit Class of Service Extensions’ page.

28

Cordless Phone Registration

The cordless extensions are shown as registered or not registered.

When Register a handset is selected a prompt is displayed indicating that the ‘REG’ key on the cordless phone should be selected and that the PIN is 1234. The system is set in registration mode for 30 seconds

To unregister an extension select Unregister.

29

Date & Time Settings

Use this screen to program Time and Date settings for your system.

Date

Use this field to enter the system Date - the time is in the MMDDYY format, MM is the month, DD is the day, & YY is the year.

For example, 3rd May 2006 =050306

Time

Use this field to enter the system time - the time is in the 24- hour clock format.

30

5

Using Your Mitel 1000 Phone System

Note

System Description

• The Mitel 1000 is an Integrated Communications System supporting all your voice & data needs.

• The Mitel 1000 can accommodate 2 CO lines and 2 IP Trunks.

• The Mitel 1000 system can accommodate 4 wired Featurephone /

Standard phones, as well as 4 cordless sets.

• The Mitel 1000 Featurephone has a simple-to-use menu-driven interface.

• A doorphone is available that can be programmed to ring any extension. It is connected to Extension 23. A doorstrike output is also provided for activating an automatic door opener.

• External Music-on-Hold can also be used. This is provided using the optional Music-on Hold module. If installed it is connected to an extension position.

Introduction to your Mitel 1000 Phones

There are four wired and four cordless extension positions available on the

Mitel 1000.

The wired positions can be equipped with a Featurephone or standard telephone sets.

The cordless positions are equipped with the proprietary cordless phone.

The proprietary Featurephone and cordless phone are designed to simplify the use of the system by providing integrated features on the phones.

If a doorphone is installed it uses a wired extension position (extension 23) thus reducing the wired telephones to three. See page 97 for instructions on programming the doorphone.

Installing the External Music-on-Hold module also uses an extension position.

If both are installed the number of available wired telephones is reduced to two. See page 98 for instructions on programming the external Music on Hold module.

31

Getting Started

This section of your Owner’s Manual is your guide to using the Mitel 1000 system and its features, with either a Featurephone or a standard telephone.

It also explains how to program system settings using your Featurephone.

Read the section ‘System Featurephone’ on Page 33 to understand how to operate the menus and use the other features of your Featurephone.

To get up and running with your Featurephone, read the section ‘Getting

Started – Basic Call Features

’ on page 41.

If you are using a standard telephone, read the section ‘Using a Standard

Telephone

’ on page 49.

If you are using a cordless telephone, read the section ‘Using a Cordless

Telephone’

on page 38.

When you are ready to use additional call features, refer to the section

‘Additional Call Features’ on page 53.

To control which numbers system users may dial, refer to ‘Class of Service’ on page 62.

For ‘Programming Additional System Options’, such as Doorphone &

Doorstrike, see page 69.

Your Mitel 1000 system comes with an integrated Voicemail functionality, as a result a number of powerful Voice Services are available. Details are given in

‘Using Voicemail

’ on page 62.

32

Handset

System Featurephone

Introduction to your system Featurephone

The system Featurephone are highly featured display telephones for use with your Mitel 1000 system.

It features a 4-line display that contains prompts and menus with selectable options. This unique menu-driven interface makes the system simple to use, and no codes are needed to program and activate features.

The Featurephone is also equipped with a data port, positioned on the lefthand side of the phone. This data port is used primarily for a modem from a

PC to directly connect to the extension.

System settings are also programmed via a Featurephone using the intuitive menu-driven interface, without the need for special codes.

The Featurephone has eight programmable keys, which are pre-programmed to access CO lines, and four function keys that group frequently used features.

The Featurephone is equipped with a speakerphone, so you can make calls, receive calls and use its features without lifting the handset.

Mute Key Speakerphone Volume

Keys

4 Function Keys:

Hold

Programming

Messages

Directory

Message waiting/ Ringing indicator

6 Display Keys

8 Programmable keys.

Numeric Keypad Clear Key Scroll / Edit keys

Using the Featurephone display

The Featurephone' display presents various prompts and information, and provides selectable options to the extension user.

Prompts and information

Prompts tell you what action to take, or warn of an incorrect action. For example, an attempt to access the system programming menus from the wrong extension will result in the prompt ‘Programming refused’.

When your Featurephone is not in use, its display shows the time and date on the top line. To set the time and date, see page 61.

When you dial an external number, the display shows the digits as they are dialed. The call duration is also displayed.

33

When you make an internal call, the extension number you dial is displayed. If the extension has been programmed with a name, the name is displayed. The call duration is also displayed.

You can display caller numbers (or names) on your Featurephone display.

The duration of external calls is displayed on the top line of the display.

Menus

When the Featurephone is idle, the Idle Menu is presented containing a large number of options displayed in groups of three. This menu, showing the first three options, is shown below. (Use Scroll Keys below display to scroll up and down).

If you are on a call or operating a feature, the menu changes to offer only those options relevant to what you are doing. Also, when features such as

Extension Lock are set, the first prompt on the display becomes the option to cancel the activated feature.

When activating certain features it is necessary to select the extensions on which you wish to activate the feature. In this case the Extension Menu lists all the extensions connected to the system. Similarly, a line Menu may be presented listing all the CO lines and IP trunks connected to the system.

Using the display Keys to select menu options

The six display Keys, located on each side of the display, are pressed to select the menu option shown alongside on the display. This will either activate a feature, cause another menu to be displayed, or select items from a list.

When selecting from a displayed list, (e.g. Extensions from the Extension

Menu), selected items will be denoted by a

♦ next to the item. Unselected items will be denoted by a

◊ next to it. Selecting an item with a ◊ alongside causes the item to be selected and the symbol to change to

♦, and vice versa.

Using the Scroll Keys

The Scroll Keys are located under the display and are used to scroll up and down through the display options as well as back and forward when text is being entered. When the Scroll Down Key (Ô) is pressed while scrolling through the display options the next three available choices are shown.

Conversely, pressing the Scroll Up Key (Ñ) will take you back up the display to the previous choice.

Using the Clear Key “C”

If you press the Clear key “C” for 2 seconds when on a call it will clear the call down.

When you are scrolling through menus pressing the C key steps back to the previous level menu.

34

Note

Note

If you are entering digits before lifting the handset, or entering text, pressing the C key deletes the last digit on the display.

Using the Keypad

The Keypad can be used to enter digits when dialing or text when programming names.

How to enter text when programming names.

Press 2 once for A, twice for B, and so on. (Pressing 2 continuously loops through ABCabc2). Press 3 once for D, twice for E, three times for F, and so on.

Selecting a different key moves the cursor on automatically to the next location. If the next letter is on the same key you can either wait for two seconds for the cursor to move on or press the right Scroll Key to move to the next location. Pressing 1 or 0 and waiting two seconds gives a blank space.

Pressing the Clear Key C deletes the last letter on the display.

You can use the scroll Keys to move back and forward through the text

A maximum of ten characters per name, including spaces, can be entered.

Using the Programmable Keys / Line Keys

There are eight Programmable Keys on the Featurephone. The first four keys are programmed as, Line 1 and Line 2, IP Trunk 1, IP trunk 2. The Line Keys incorporate a light, which is lit on all Featurephones when the associated line is selected.

The light is green on the Featurephone using the line and red on all other

Featurephones. When a call on a line is put on hold the associated Line Key light flashes on all Featurephones.

Should you wish to allocate alternative functions to these keys this can be facilitated using Key Programming. (See page 36).

Using the Speakerphone Key

You can use the Speakerphone Key to have a conversation without having to lift the handset. Press the Speakerphone Key to go off-hook, as if the handset were lifted with the Featurephone speaker and microphone replacing the handset. Pressing the key again goes back on-hook, as if the handset were replaced.

You may also use the Featurephone with a headset. (See: 'Using your

Featurephone with a headset

’ on Page 48).

The Speakerphone key has a red light, which is lit whenever the

Speakerphone Key has been pressed to go off-hook or to turn on the speaker.

Pressing the Speakerphone Key at any time during programming exits the programming menus and returns the display to the Idle

Menu.

Using the Volume Key

To adjust the speaker volume, press the Volume Key when in Speakerphone

Mode.

To adjust the handset receiver volume, press the Volume Key when in

Handset Mode.

To adjust the ringing volume, press the Volume Key when the Featurephone is ringing.

The Volume level increases/decreases by one step for every press of the Volume Key.

35

Using the Mute Key

The Mute Key can be pressed when you are using the handset or in

Speakerphone Mode. When pressed, the other person on the call cannot hear you. The Mute Key has a red light, which is lit when Mute is active.

The Ringing / Message Waiting Light:

There is a red light on the top right-hand corner of the Featurephone. This light flashes when there is an incoming call. It also lights up when a voice message has been left in your Voice Mailbox.

Using the Function Keys

There are four Function Keys located directly above the Featurephone display. Particular features are grouped under these keys, as follows:

HOLD: This key puts external calls on hold

PROGRAM: This key accesses the options available to customize your

Featurephone settings. It also accesses system programming from the

Programming Extension only.

MESSAGE: This key accesses Voicemail. (See page 62 for Voicemail).

DIRECTORY : This key allows you to program and dial numbers in the

System and Personal Speed Dial lists.

Customizing your Featurephone

This PROGRAM Key accesses the options available to customize your

Featurephone settings.

Setting the language

The text prompts on the phone are in English in default. The options to choose

French or Spanish are provided.

Press the PROGRAM Key

Select Language

Select English, French or Spanish.

To turn on Automatic answer mode

You may program your Featurephone to work in 'Auto-answer mode'. In this mode the Speakerphone Key light flashes red, and when you receive an internal call you hear a burst of tone and the call is connected automatically.

You can speak to the caller without touching the Featurephone.

From your Featurephone, press the PROGRAM Key

Select ‘Auto answer'.

Select the required option – ‘Set auto answer’ or ‘Cancel auto answer’, to set and cancel the Automatic answer mode respectively.

Press the Speakerphone Key to finish programming.

To program a feature onto a programmable key on your extension

You may re-program any or all of the 8 Programmable Keys located on the

Featurephone. You can program these keys to select lines, extensions, features or speed dial numbers.


Press the Scroll Down Key (Ô) until ‘Key Programming’ is displayed.

Select ‘Key programming’.

Press the Programmable Key to be programmed. A list of options appears on the display.

36

Note

Select the required feature to be programmed onto the key. Use the Scroll

Down Key (Ô) to scroll down to view the list of available features. For example, to program the key with a speed dial number, select the ‘MF Digits to

line’ option.


If you are programming the key to call an external number remember to precede the number with a

9 to select the CO line or 8 to select an IP Trunk.

To turn on Headset Mode

You turn Headset mode on and off via the PROGRAM Key


Press the Scroll Down Key (Ô) until ‘Headset Mode’ is displayed.

Select ‘Headset mode’.

Select the required option – ‘Headset on’ or ‘Headset off’. Once selected, the display will show ‘Headset On’ or ‘Headset Off’ and then revert to the Idle

Menu.

Press the Speakerphone Key to finish programming. The options to Turn headset On? And turn Headset Off are shown on the Idle display.

The handset does not operate in Headset Mode.

To set a ringing tone on your Featurephone

You can select one of six ringing tones.


Press the Scroll Down Key (Ô) until ‘Ringing Options’ is displayed.

Select ‘Ringing options’.

Select ‘Tone 1’, ‘Tone 2’, ‘Tone 3’, ‘Tone 4’, ‘Tone 5’ or ‘Tone 6' which will cause the selected tone to sound.

Select ‘Confirm’ to use the chosen tone. On the display ‘Ring type set’ will appear and then the display will revert to the Idle Menu.


To set the display contrast on your Featurephone

You may choose from four levels of display contrast.


Press the Scroll Down Key (Ô) until ‘Contrast Options’ is displayed.

Select ‘Contrast options’.

Select ‘Level 1’, ‘Level 2’, ‘Level 3’ or ‘Level 4’ to set a contrast option. The prompt ‘Contrast set’ appears on the display.


To enter system programming

If your extension is the Programming Extension you have access to the system programming options. If you select this option you will be prompted to enter the System Programming Password. If this option is selected from any other extension the display will show ‘Programming Refused’. Again, the default

Programming extension is extension 20.

From the Programming Extension, press the PROGRAM Key

Press the Scroll Down Key (Ô) until ‘System programming’ is displayed.

Select ‘System programming’.

Enter the System Programming Password to access system programming

(1111 in default).

37

Note

Background music

This feature allows an extension to have music played over the speaker of a

Featurephone while the extension is idle. This background music is supplied only if there is an external music source connected to the system. This background music is disconnected as soon as the user goes off hook or a call is presented to the extension.


Press the Scroll Down Key (Ô) until ‘Background Music’ is displayed.

Select the required option – ‘Background music on’ or ‘Background music off’.


The External Music on Hold Extension must be selected before you can turn background music on/off.

Using the Cordless Telephone

Rock Key

Talk Key

Star & Ringer Off Key

Recall Key

Internal Key

The cordless telephone is designed for use with the Mitel 1000. The keys are as shown. For a detailed description of the functionality see Appendix A on page184.

Soft keys

Services Key

On/Off and End Key

Hash, Lock & Pause Key

Calls Key

38

Note

Note

Note

Making a call

Press

Dial the number you want to call. The number appears on the display and is dialed.

Call timer:

The call timer shows the duration of your current call on display.

Out of range warning:

If you move too far away from the base

Mitel 1000 during a call, your phone will sound an alert tone, and will flash. You need to move closer to the base Mitel 1000 or your call will be disconnected.

Low battery warning:

If your phone is almost out of battery during a call, it will sound and alert tone. Place your phone on the base Mitel 1000 for charging as soon as possible or it would turn off when it is out of battery. Placing the phone on the base Mitel

1000 for charging will end the current call.

Preparatory Dialing (Pre-Dial)

With pre-dial, you can see and edit the number you are calling on the display before dialing it.

Enter the number you want to call. The number appears on the display.

Deleting digits: Press CLEAR to delete an incorrect digit. If you press CLEAR on the last digit, your phone will return to standby.

To Dial the number Press

Saving a number from pre-dial

1. Enter the number in standby. The number appears on the display

Note

3.

4.

5.

Memory Full:

If the phonebook is full, FULL is displayed, and then the phone returns to standby.

Enter the name for the record. You must enter a name.

Press .

Edit the number for the record if necessary. You must enter a number.

End a call

Press or place the phone on the base unit or charger.

39

Answer a call

When you receive a call, the phone will ring and will flash in the display.

1. Press to answer the call.

Redial a number

Your phone records the last 10 numbers you have dialed. The most recent call is stored at the top of the list. Only the first 20 digits of each number are stored.

To redial the last number dialed: -

Press .

Press REDIAL. The last dialed number appears on the display and is dialed.

To redial one of the last 10 dialed numbers:

Press during standby. The redial list appears on the display.

Press to select the number you wish to redial. Press .

Speakerphone calls

Speakerphone provides the convenience of talking to the caller without holding onto the phone. You can communicate by using the speaker/microphone of the phone. Speakerphone also allows others in the room to be involved in the conversation.

Press OPTIONS when on a call. Select SPEAKER. Press OK.

1. You can hear the caller over the loudspeaker and you can speak via the microphone.

2. Repeat step 1 to switch off the speaker.

Turning off the ringer

Press SILENT when the phone is ringing to turn off the ringer for the call.

You can also press and hold

*

when the phone is in standby to turn off the ringer for all the calls. (Press and hold again to turn on the ringer.)

Adjusting the volume on a call

You can increase or decrease the volume during a call. There are 3 volume levels for selection.

To adjust the volume, during a call:

1. Press The display shows the current volume level. Press to adjust the volume.

Using Mute on a call

During a call, if you wish to speak to someone privately without having the caller hear your conversation,

Press MUTE. The caller cannot hear you, but you can hear the caller.

Press UNMUTE to communicate with your caller again.

For more detailed instructions on the Digital Cordless phone see page 184.

Message Waiting Indication

A message indication symbol appears on your Digital Cordless phone and a broken dial tone is heard when going off hook, when a message has been left in the Answering Machine or the extension’s voicemail.

To access the message press and dial

*

.

To access the answering machine dial 0 as the extension number.

The default password is 1111 for all mailboxes.

40

Featurephone– Basic Call Features

Making and Answering Calls

Making an external call.

There are two basic modes of operation available for making CO Line calls. In the normal mode, which is the default, a line access digit (9 or 8) is dialed to select a Line.

If Automatic Line selection is programmed you do not enter the line access code.

Making an external call in normal mode

1. Press a Line Key to select a free line and when dial tone is returned dial the external number.

Or

2. Dial 9, (to select a CO Line) or Dial 8, (to select an IP Trunk). When dial tone is returned dial the external number.

Making an external call with Automatic Line selection programmed

1. Press a Line Key to select a free line and when dial tone is returned dial the external number.

Or

2. Lift the handset, or use a Speakerphone Key, and dial the number. The system automatically selects a free line and the number is dialed.

Making an external call in Pre-dial mode

If you do not lift the handset you may enter digits in Pre-dial mode by dialing 9 or 8 followed by the external number in normal mode or dial the external number when Automatic Line selection is programmed. Digits will not be sent to line until you lift the handset, press the Speakerphone key, or select 'Dial' from the display.

You can edit the number you have entered prior to sending to the line, by using the left-hand Keypad ‘Edit Key’, located below the keypad.

To make an internal call in normal mode

You can place an internal call in one of the following ways:

1. Select the ‘Internal Call’ option on the display and select the desired extension from the list

2. Dial the extension number (20 – 23 or 31-34) and select 'Dial'.

3. Lift the handset and dial the extension number.

The display will show the extension number, or, if programmed, the extension’s name.

To make an internal call with Automatic Line selection programmed

1. Select the ‘Internal Call’ option on the display and select the desired extension from the list.

The display will show the extension number, or, if programmed, the extension’s name.

41

Note

Speed Dial list

Each extension can program up to 30 Individual Speed Dial numbers. You can also program 99 system speed dial numbers and names. Users of the system can access the system speed dial numbers, provided they are not restricted from dialing the number because of their Class of Service.

An option is available where extensions can dial numbers in the system speed dial list even though they are normally restricted from dialing them. See system Speed dial override programming on page 103 and page 171.

If a number or an incoming call matches a number in the system speed dial list, the name in the list will be displayed.

To add or delete a Personal Speed Dial number

3.

4.

5.

Enter the Index 01-30

Enter the number and press Confirm

Enter the name and press Confirm.

To delete an entry select delete when the index is entered.

For configuration via the web interface, see page 105.

To dial a Personal Speed Dial number

Press the DIRECTORY Key.

Select ‘Personal Speed dial’.

Enter the first letter of the name or scroll through the entries to find the entry you want.

When you have selected the number or name you want a free line is automatically selected and the number is then dialed.

If some numbers are entered without names they are presented at the end of the list.

To add or delete a System Speed Dial number

1. Press the DIRECTORY Key.

3. Enter the Index 01-99

4. Enter the number and press Confirm

5. Enter the name and press Confirm.

To delete an entry select delete when the index is entered.


To dial a System Speed Dial number

Press the DIRECTORY Key.

Select ‘System speed dial’.

Enter the first letter of the name or scroll through the entries to find the entry you want.

42

When you have selected the number or name you want a free line is automatically selected and the number is then dialed.

If some numbers are entered without names they are presented at the end of the list.

To answer a call

When the Featurephone rings, you can do one of the following:

Note

3. Press the Speakerphone Key.

From a standard telephone, lift the handset.

Reseize

The Reseize option is displayed when dialing an external call and when an external call is answered. If Reseize is selected the current call is released and the line is re-seized presenting external dial tone.

Call Recording

If an extension is equipped with a voice mailbox they can be provided with the ability to record a call. The extension is programmed to allow call recording.

When allowed to record a call the option Record the call is provided on the

Featurephone menu. Recorded calls are saved as new messages in the extension’s voice mailbox. See page 104 for programming via the web interface and page 173 for the Featurephone interface.

Holding & Transfer Calls

To place an external call on hold

1. While on the cal press the Hold key or select ‘System hold’ on the display.

2. To retrieve the call, select ‘Return to line’ on the display or press its

Line Key.

If an extension has two calls on system hold, selecting ‘Return to line’ will return the extension to the first call that was put on hold.

To transfer a call to another extension

1. While on the call, select ‘Internal Transfer’ on the display.

2. Select the desired extension from the extension list presented on the display, or dial the extension number.

Note

You can transfer a call to an extension when the extension has answered, while ringing the extension, or while the busy tone is being received from the extension.

To transfer a call to an external number

1. While on the call, press the Scroll Down Key (Ô) until ‘External

transfer’ is displayed.

43

3.

4.

Select a free line and dial the number.

When the call is answered, press ‘Transfer’.

Transferring an external call to an external number ties up two exchange lines. Such calls are called trunk-to-trunk calls.

Note

Note

To make an external consultation call

While on an external call you can contact another external number to make an enquiry, as follows:

1. Press the Scroll Down Key (Ô) until ‘External Consultation’ is displayed.

2. Select the ‘External Consultation’ option on the display.

3. Select a free line and dial the number.

4. When the call is answered, you can go back and forth between both calls.

Select the ‘Return and hold’ option on the display each time you want to swap to the other call.

Re-Directing calls

This allows you to re-direct a call that is ringing at your Featurephone.

To re-direct a call ringing at your extension

1. When a call is ringing at your Featurephone, select ‘Re-Direct the call’ on the display.

2. Select a free extension from the extension list presented on the display. The call is presented to the selected extension and stops ringing at your Featurephone. If you attempt to deflect a call to an unavailable extension it will continue ringing.

To forward a call ringing at your extension to voicemail

1. When a call is ringing at your Featurephone select Forward to

Voicemail ' on the display.

2. Incoming calls are deflected to the Answering Machine and internal calls are deflected to the extension’s voice mailbox. If the voicemail is busy the call continues to ring at your Featurephone.

For information on setting up and using a Voice Mailbox refer to page 62.

Forwarding Calls

To forward all calls from your extension

Before you leave your extension, you can forward all your calls to ring at another extension. Alternatively, you can forward all external calls presented to your extension to an external number.

1. From the Idle Menu, press the Scroll Down Key (Ô) until ‘Extension

Forward’ is displayed.

44

a) Enter an internal number if you want to Forward all your calls to another extension. b) Enter 9 followed by an external number if you want to Forward external calls to an external number. c) Forward will be ignored for internal calls. For internal calls the phone will ring (only If External forwarding is set to the 'External

calls only' option). d) If your extension is allocated a voice box select 'Forward to Voice

Mail'

WARNING

It is possible that an extension may misuse the External Forward facility.

The default setting is that no extension is allowed to set the facility.

Note

Note

Once set the Idle Menu will show the option ‘Cancel Forward’. To cancel the forwarding, select ‘Cancel Forward’.

Broken tone will be heard at your extension until all call forwarding is cancelled.

You cannot Forward to an extension that has the ‘Do Not Disturb’ feature set.

Forwarding an external call to an external number ties up two exchange lines. Such calls are called trunk-to-trunk calls.

To forward your calls to you while you are at another extension

The ‘Follow Me’ feature allows you to set a call Forward to another extension after you have left your extension.

1. From the Featurephone answering the calls, press the Scroll Down

Key (Ô) until ‘ Extension Forward’ is displayed.

‘Follow me’. You will be prompted to enter your extension number and your Extension Lock Password. (Default Password is

321). Once these details are entered the forwarding is activated.

Once set the Idle Menu on your own extension will show the option ‘Cancel Forward’. To cancel the ‘Follow Me’ forwarding, select ‘Cancel Forward’.

Note

‘Follow Me’ will not forward a call from an extension, if the call has been previously forwarded by ‘Follow Me’ to that extension.

To Forward calls when your extension is busy

The ‘Forward When Busy’ feature allows you to forward all your calls to ring at another extension if your extension is busy (engaged). Alternatively, you can forward all external calls to an external number if your extension is busy. In this case, internal calls will not be forwarded but will be given the busy tone.


Forward’ is displayed.

45

a) Enter an internal number if you want to forward all your calls to another extension. b) Enter 9 followed by an external number if you want to Forward calls to an external number. A programming option is available to allow both internal and external calls (or external calls only) to be

Forwarded externally.

WARNING

To set a 'Forward when Busy' from a standard phone the code is '733' followed by the destination number.

It is possible that an extension may misuse the External Forward facility. The default setting is that no extension is allowed to set the facility.

Note

When ‘Forward when busy’ is enabled on an extension to

Forward to an external number, external incoming calls will

Forward but internal calls will not.

Forwarding an external call to an external number ties up two exchange lines. Such calls are called trunk-to-trunk calls.

To cancel a forward when busy

1. From the Idle Menu, select ‘Extension Forward’.

‘Forward when busy’. The forwarding is automatically cancelled and the display returns to the Idle Menu.

To forward calls when your extension does not answer

The ‘Forward On No Answer’ allows you to forward all your calls to ring at another extension if there is no answer at your extension after four rings.

Alternatively, you can forward all external calls to an external number if your extension has not answered after four rings. In this case, internal calls will not be forwarded but will continue to ring your extension.

1. From the Idle Menu, press the Scroll Down Key (Ô) until ‘ Extension

Forward’ is displayed. a) Enter an internal number if you want to forward all your calls to another extension. b) Enter 8 followed by an external number if you want to Forward external calls to an external number.

WARNING

It is possible that an extension may misuse the external forwarding facility. The default setting is that no extension is allowed to set the facility.

46

Note

If ‘Forward On No Answer’ is enabled on an extension to forward to an external number, external incoming calls will forward, but internal calls will not. Forwarding an external call to an external number ties up two exchange lines. Such calls are called trunkto-trunk calls

Forwarding an external call to an external number ties up two exchange lines. Such calls are called trunk-to-trunk calls..

To cancel a Forward on No Answer forwarding


Forward’ is displayed cancelled and the display returns to the Idle Menu.

Forwarding incoming calls

This feature allows any extension to set a forwarding for calls received on an exchange line or IP Trunk.

Setting Incoming call forwarding from a system phone

1. From the Idle Menu, press the Scroll Down Key (Ô) until ‘Incoming

Call forwards’ is displayed and select it.

2. Select the line or IP Trunk.

3. Select the Option required and enter the destination number.

‘Answering Machine’ to forward the calls to the answering machine.

WARNING

It is possible that an extension may misuse the external forward facility.

Cancel incoming call forwarding from system phone

If ‘All Call Forward’ is set incoming I/C Call Forward’ is shown on the display.

2.

3.

The display will show the lines. Select the required line

Select the forwarding type to be cancelled.

Conference Calls

This feature allows you to hold a three-way conversation between three extensions, or between two extensions and a CO line, or between two exchange lines and an extension.

To hold an Internal Conference

1. When on a call, press the Scroll Down Key (Ô) until ‘Internal

Conference’ is displayed.

3.

4.

Select the extension to be included in the conference.

When the extension answers, select ‘Conference’ on the display.

47

Note

To hold an External Conference

1. When on a call, press the Scroll Down Key (Ô) until ‘External

Conference’ is displayed.

3.

4.

Select a free line and dial the external number.

When the call is answered, select ‘Conference’ on the display.

An external conference call ties up two exchange lines.

At the start of a conference call a single tone is presented to all parties to indicate that the call is a conference call.

Using your Featurephone with a headset

Your Featurephone is equipped with a socket for a Headset.

Plug a headset into the socket.


Select ‘Headset Mode’ and select ‘Turn Headset On’. The phone is now programmed to operate with a headset.

'Turn Headset Off?' is now displayed to allow you to revert to handset mode.

If ‘Turn Headset Off?’ Is selected the menu updates to show ‘Turn Headset

On?’ You can turn the headset on and off as required.

To return the phone to normal operation, press the PROGRAM Key and select

‘Headset mode’. Select ‘Turn Headset Off’

To make an internal or external call when using a headset

Press the Speakerphone Key and dial your calls in the normal way.

To clear down (end) a call when using headset

Press the Speakerphone Key.

To answer a call when using a headset

Select the ‘Answer the call’ option on the display, or press the Speakerphone

Key.

48

Using a Standard or cordless Telephone

Feature Access Code List

You may access the range of Mitel 1000 features with a standard or cordless telephone. To use a feature, dial the appropriate code from the list below.

If your telephone is equipped with memory keys you may program feature codes onto the keys - refer to your telephone user guide for instructions. On the cordless phone you can program codes under the Services (SER) key.

See Page 188.

Answering machine on/off

Alarm Call

Alarm Call cancel

Barge –In

Call Pick-up

Call Recording

Call Waiting Tone Protection

737

718

Line Forward All Calls

Line Forward when busy

718*

709

727

Hookflash 795

Line Forward on No Answer

Internal Call Waiting

Night Service

Open the Door

725 (Hookflash 725) Page – Featurephone

792

793

794

Hookflash 8

738

731

716

Forward All

Forward when busy

Forward on No Answer

Do Not Disturb – set/cancel (Not available to extension 20)

Door Open

Extensions - Wired

Extensions - Cordless

Extension 20

Extension Lock – change code

Extension Lock - lock/unlock

External Call Hold

Follow Me

Forward Recall

Line Access – CO lines

Line Access – IP Trunks

732 xx

733 xx

734 xx

Pick up parked call

Redial

Redial IP call over standard line

712

77

Hookflash 77

739

731 (Hookflash 731) Return to call placed on systemhold

20-23 Return and hold in Two Call handling

31-34

0

714 xxx

Return and release in Two Call handling

Ring Back

Saved Number Redial

719

Hookflash 2

Hookflash 1

Hookflash 5

781-785

713 xxx

Hookflash

Speed Dial – accessing personal numbers 74(01 -30)

Speed Dial – accessing system numbers 400-499

735 (Password) xx Speed Dial – programming personal numbers

Hookflash 722 Voice call (to page an individual

Featurephone)

9 Voice Mail Access

75(01 -30)

715

8 Voice Mailbox number

*

710

49

3.

4.

5.

Making CO Line Calls

There are two modes of operation available for making CO Line calls. The normal mode, which is the default, a line access digit is dialed to select a CO

Line. If Automatic Line selection is programmed you do not enter the line access code.

To make an external call in normal mode

1. Lift the handset, or use a Speakerphone Key, if available on your telephone.

2. Obtain a free line in one of the following ways:

Dial 9, (to select a CO line).

Dial 8, (to select an IP Trunk).

Dial the number you require.

To make an external call in Automatic Line selection mode


4.

5.

Dial the number.

The system automatically selects a free line and the number is dialed.

To make an internal call in normal mode


2. Dial the desired extension

number (20 -23 or 31-34).

To make an Internal call in Automatic Line selection mode


2. Press hookflash and dial the desired extension number (20-23 or 31-

34)

To answer a call

When the telephone rings, lift the handset, or use a Speakerphone Key if available on your telephone.

Holding & Transfer Calls

To place a call on hold

1. Press the Recall Key or Hookflash.

If you replace the handset, you can continue to use your telephone. The held call will call back within ninety seconds provided your telephone is idle. If you are busy on the telephone after the ninety seconds the call will ring when the handset is replaced.

To transfer a call

1. Press the Recall Key or Hookflash. extension

number and replace the handset.

50

To make an external consultation call

While on an external call you can contact another extension to make an enquiry, as follows:

1. While on an external call, press the Recall Key or Hookflash on your telephone.

2.

3.

Dial the extension number.

To return to the external call and place the extension on hold, press

Recall or Hookflash and dial 2.

4. To return to the external call and release the extension, press Recall

(Hookflash) and wait or press Recall (Hookflash) and dial 1.

To transfer the external call to the extension

replace the handset when talking to the extension

with the external call on hold.

Extension Forwarding

Forward all calls

1. Lift handset or use Speakerphone if available.

3.

4.

Dial the extension number, or

Dial the external phone number (including line access code 9)

Cancel Forward all calls


Forward calls when your telephone is busy

1. Lift handset or use Speakerphone if available

3.

4.


Dial the external number, (including line access code 9)

Cancel Forward a call on busy


Forward calls when your telephone is not answered (after four rings)


3.

4.


Dial the external phone number (including line access code, e.g. 9)

51

Cancel a Forward a call on no answer


Line Forward / Incoming Call Forwards.

Forward all calls


2. Dial 792 followed by the line number (1-4)

3.

4.


Dial the external phone number (including line access code 9)

Cancel Line Forward all calls


2. Dial 792 followed by the line number (1-4).

Forward calls when line is busy


2.

3.

4.

Dial 793 followed by the line number (1-4)


Dial the external number, (including line access code 9)

Cancel Line Forward when busy



Forward calls when line is not answered (after four rings)


2.

3.

4.

Dial 794 followed by the line number (1-4)


Dial the external phone number (including the line access code, e.g.

9)

Cancel Line Forward on no answer



52

2.

3.

4.

Programming and dialing speed dial numbers

If you have a standard telephone, you can program up to 10 Personal Speed

Dial numbers.

To program a Personal Speed Dial number

1. Lift the handset, or press the Speakerphone Key, if available.

Dial the code 75.

Enter the location (01 - 30) where you want to store the number.

Dial the number you want to store.

Note

The line access codes 'e.g. 9' is not required

To dial a Personal Speed Dial number

1. Lift the handset, or press the Speakerphone Key, if available.

2. Dial the code 74.

3. Dial the location (01 - 30) of the number you wish to access. The number is automatically dialed.

To dial a System Speed Dial number

Dial the location code (401 – 499) of the number you wish to access. The number is automatically dialed.

Voicemail

Turn on your voicemail

When you are allocated a voice mailbox ‘Forward on no answer’ is automatically set to your Voice box

The Voice code is 710

To forward all your calls to your voicemail Dial 732 followed by 710

To forward on busy to your voicemail Dial 733 followed by 710

Additional Call Features

Redial

Use the Redial feature to redial the external number you most recently dialed.

A line is selected automatically.

To redial the last external number dialed

From the Idle Menu, select ‘Redial last number’.

From a standard telephone, the code is 77.

Saved Number Redial

In addition to the Last external number the previous 5 numbers dialed are also stored and may be redialed.

From the Idle Menu, select ‘Saved Numbers’.

Select the number to be dialed.

53

From a standard telephone the codes are 781 – 785 for saved numbers 2 - 6.

The first saved number is the Last Number Redial code 77.

Call Pick-up

This feature allows the user to pick up any call, ringing at another extension.

These calls include

Internal calls

External calls

CLI Routed calls

Incoming ringing calls routed to a single extension

To pick up a call ringing at another extension

From the Idle Menu, select the ‘Call Pick-Up’ option on the display.


Ring Back

If the extension you call is busy, use the Ring Back feature to have the extension call you back when it becomes free. If you dial for a CO line and no lines are free, use the Ring Back feature to receive a CO line as soon as one is available.

To have a busy extension call you back when it becomes free

When you have called a busy extension, select ‘Ring Back’ on the display.

When the extension becomes free, your extension will ring and your display will show ‘Ring Back from Extension’.

Select ‘Answer the Call’ or pick up the handset to ring the extension.

From a standard telephone, dial Hookflash 5 when you have called a busy extension.

To receive an exchange line as soon as one is available

When you have dialed for a line and none are free, select ‘Ring back’ on the display.

Select ‘Answer the Call’ or pick up the handset to select a line.

From a standard telephone dial Hookflash 5 when you have dialed for a line and no lines is free.

Camp on Busy

‘Camp on Busy’ allows you to have your extension call a busy extension as soon as it becomes free.

When you call an extension and get a busy (engaged) tone, stay off-hook and when the called extension becomes free it will start ringing.

Barge-In

The Barge-In feature allows extensions break in on other extension calls.

When an extension is programmed to have the barge-in feature, the prompt

“Barge-In” is added to the idle menu on the Featurephone. See Page 104 for programming from the management application and page 163 for programming from the programming Featurephone.

To barge-in on an extension select “Barge-In” on the idle menu. The extension list is displayed. Select the extension to barge-in on. The extension must be on a call and this is indicated by a “

♦”.

If the barge in is successful the text “Barged-In” is displayed.

54

Note

A programming option is available that disables the warning tone when bargein is activated. See page 98 for programming from the web application and

Page 164 for programming from the programming Featurephone.

A further option is provided to protect extensions from “Barge-In”. See page

104 for programming from the management application and Page 163 for programming from the programming Featurephone.

If an attempt is made to barge-in on a protected extension the display shows

“Barge-In Prohibited”.

If barge-in is unsuccessful for any other reason the display shows “Barge-In

Failed”.

Barge-in is not allowed if the extension selected is not on a call, is transferring a call, is listening to voice mail or is in a three way conference call.

Note

Note

A maximum of three simultaneous barge-in and conference calls are allowed in the system.

From a standard analog or cordless telephone, dialing the code 709 followed by the extension number, activates “Barge-In”.

Call Waiting from another extension

If you get a busy tone, when you call an extension, you can alert the busy extension that you wish to contact provided the extension is not protected against receiving Call Waiting tones. (See ‘Call Waiting Tone Protection’ on page 163). An audible tone will sound on the called extension, and the message ‘Call wait. – Ext xx’ will appear on its display. Options to accept the call are offered on the display.

To present a busy extension with a Call Waiting tone

Select ‘Waiting tone’ on the display when a busy tone is returned from an extension.

From a standard telephone, the code is Hookflash 8.

To accept a waiting call

If another extension presents you with Call Waiting, this will be indicated on your display and you will hear the Call Waiting tone, provided your extension is not protected against Call Waiting tones.

Select one of the options presented on the display.

If you ignore the Call Waiting tone for a short period the Call

Waiting offer is rejected and the calling telephone is presented with the message ‘Call Waiting Rejected’.

Call Waiting from external calls

If you are on a call and your extension is presented with an external call you will hear a call waiting tone provided your extension is not protected against call waiting tones.

55

Note

The line the call is on will be indicated on your display. If you select the second call, by pressing the line key associated with it, the first call will be automatically released.

Call Park

The Call Park feature allows you to put an external call on special hold by

‘parking’ it in the system. Any extension may then pick up the call.

To park and retrieve a call

On a Featurephone, select ‘Call Park’ on the display.

‘Pick up park’ is then displayed on the top line on the display on all

Featurephone. Select this option to retrieve the parked call.

Only one call may be parked in the system. A parked call will recall after three minutes

On a standard telephone, the code is Hookflash 712 to park a call and 712 to retrieve it.

Storing and redialing caller numbers

The Caller ID service is available on CO lines. If you subscribe to this service, your network sends the telephone number of callers to the Mitel 1000

(provided the caller has not elected to restrict the network from presenting their number). The telephone number (or associated name) is displayed on the ringing Featurephone.

The Caller ID information is also shown if the extension is equipped with a standard phone which supports the service.

Your telephone number will also be presented to persons you call, unless you restrict your number from being presented.

The Caller ID store automatically stores information relating to unanswered calls to the system (answered calls can also be stored). The information stored is the caller telephone number, and the date and time of the call.

Information is not stored for calls with withheld or unavailable numbers. When a new record is received and the memory is full the oldest record is discarded from memory.

The Caller ID list can be allocated as one central store of data on calls received. This store alerts extension 20 (default), by means of a display prompt, that new calls have been stored. You can also program all 4 wired extensions to store up to ten numbers each.

To examine and redial stored caller numbers

Select ‘Missed Calls - Personal’ to examine the numbers in the personal store of your Featurephone.

Select ‘Missed calls - System’ to examine the system store. This can be selected from any extension.

You will see the following information:

The number and time of the last three calls received are displayed.

If the call was answered the display will show an ‘A’ on the right-hand side of the record. If the call was not answered, the ‘A’ will not be displayed.

The date information for the displayed calls is shown for a few seconds instead of the time.

You may scroll through the stored numbers and names by using the Scroll Up

(Ñ) and Scroll Down Key (Ô) situated below the display.

If you press the display key beside a particular record the system automatically selects a free line and dials the displayed number. If the

56

extension is restricted from dialing, or if there is no line available, you will hear a busy tone.

If an ‘R’ is displayed on the right-hand side of a record, this indicates that the number has been redialed.

If an ‘A’ is displayed on the right-hand side of a record, this indicates that the number has been answered.

To set up your system to display caller numbers received on CO lines

(Caller ID service)


For configuration via the Featurephone interface, see page 160.

To associate a caller number with a name, and route its calls to an extension



Caller ID List – storing calls

To program the Caller ID lists to store all calls or unanswered calls only see page 97 for configuration via the web interface, and page 160 for configuration via the Featurephone interface.

To set up extensions with an individual Caller ID List



Paging

To make an announcement over the speakers of all Featurephone

The 'Page All Featurephones’ allows any extension to make an announcement over the speakers of all Featurephones. Only Featurephones that are page-protected will not be paged.

From the Idle Menu, press the Scroll Down Key (Ô) until ‘Page all

Featurephones’ is displayed.

Select ‘Page all Featurephones’.

Make your announcement.


To make a call over the speaker of another Featurephone

The Voice Call feature allows you to speak over the speaker of an individual

Featurephone. If the Featurephone is page-protected the voice call will fail.

From the Idle Menu, press the Scroll Down Key (Ô) until ‘Voice call’ is displayed.

Select ‘Voice call’.

Select the extension you wish to page.

Make your announcement.


To answer a Voice Call at your extension

Press the Mute Key and speak in Speakerphone Mode, or pick up the handset.

To protect Featurephone against Announcements and Voice Calls


57


Least Cost Routing

You may use this feature to have users’ calls routed over specific lines, or over a specific Network Provider. To set the feature up you associate input codes with the lines over which calls should be routed and with whatever network codes are necessary to route the call.

In addition you can choose to route the calls over different lines at various times of the day for optimum call rates. Once the facility is activated calls are automatically routed over the selected lines, and the network code is sent to the line before the telephone number.

To route a call using the Least Cost Routing feature

Select a Line Key, or dial a code for a line (9, 8) and select ‘Send digits’.

Dial a valid input code.

When a line is selected, dial the telephone number you wish to reach.

Your call will then be connected with the output code being dialed before the telephone number.

Any Line Key or line code (9, 8) can be selected above. However, the system will select the line for the call based on the input code.

To set up codes to allow calls to be routed on specific lines or networks



Least cost Routing activated automatically at set times



Sending a Forward Recall while on call

A Forward Recall signal may be required if you are using certain network services on standard CO lines, or if your Mitel 1000 is connected to another telephone system (PABX) via one of the line interfaces.

The Forward Recall feature allows you to send a hold signal forward on the line to the exchange or PABX. To send a hold signal, you must be on a call or have dialed at least one digit of the number you are calling.

To send a Forward Recall signal to an exchange or a PABX

From a Featurephone, select ‘Forward recall’ on the display.


58

Extension Set-Up options

Do Not Disturb

If your extension is set to ‘Do Not Disturb’, anyone trying to call you will receive a busy (engaged) tone. If the person trying to contact you has a

Featurephone, ‘Do Not Disturb Enabled’ will appear on its display. ‘Call Back’ and ‘Alarm call’ are the only incoming ringing that will be accepted when this feature is set.

To set Do Not Disturb on your extension

From the Idle Menu, press the Scroll Down Key (Ô) until ‘Do Not Disturb’ is displayed.

Select ‘Do Not Disturb’.

‘Do Not Disturb' is unavailable on extension 20.

To cancel Do Not Disturb on your extension

From the Idle Menu, Select ‘Cancel Do-Not-Disturb’. This option is displayed only when the feature is set.

When ‘Do Not Disturb’ is set, you will hear a broken dial tone when you lift the handset.

From a standard telephone, the code 736 is used to set and cancel this feature.

Extension Lock

This feature allows you to lock your extension to prevent unauthorized users from making external calls. You use a Lock Password to lock, unlock, or to make calls from a locked extension. The default Lock Password for all extensions is 321, but each extension may change its password. Extension

Lock Passwords can be examined from the Programming Extension.

To lock your extension

From the Idle Menu, Press the Scroll Down Key (Ô) until ‘Extension Lock’ is displayed.

Select ‘Extension Lock’.

Select ‘Lock the Extension’.

Dial your 3-digit Lock Password. (The default Lock Password is 321).



To unlock your extension

Select ‘Unlock the extension’. This display option only appears when the extension is locked.




To make a call from a locked extension

Press a Line Key, or dial the code for a line (9 or 8), as if to select a line.


Lift the handset and press either ‘Send digits’ or the Speakerphone Key.

A line will be selected.

59

Dial the number you require.

To change your extension Lock Password

From the Idle Menu, press the Scroll Down Key (Ô) until ‘Extension Lock’ is displayed.

Select ‘Extension Lock’.

Select ‘Change the lock code’.

Dial the existing 3-digit Lock Password. The default password is 321.

Dial your new 3-digit Lock Password. The new Lock Password will not be displayed when entered.



To examine Extension Lock Passwords



Alarm call

This feature enables you to set your extension to ring at a given time.

To set your extension to give you a Alarm call at a given time

From the Idle Menu, press the Scroll Down Key (Ô) until ‘Alarm call’ is displayed.

Select ‘Alarm call’.

Enter the time in the 24-hour clock format, for example, 0930 for 9.30 am.

At the programmed time the extension will give ten rings. If not answered, it will ring twice more at two-minute intervals and will then cancel.

Alarm calls must be set daily and therefore cannot be set more than 24hrs ahead.

To review and cancel a Alarm call

To review an Alarm call, select ‘Alarm call’ and the time set will be displayed.

Select ‘Confirm’ to retain the programmed time. If you wish to change the time, select ‘Change’ and enter a new time.

To cancel the alarm call, select ‘Change’ followed by ‘Confirm’.

From a standard telephone, the code 718 is used to set a Alarm call, and the code 718* is used to cancel it. A standard telephone cannot query the Alarm call time.

Extension Reset

You can reset your extension to cancel all the following features if they have been set:

Do Not Disturb

Call Forward

Call Back

Alarm call

To reset your Featurephone

From the Idle Menu, press the Scroll Down Key (Ô) to scroll downwards until

‘Reset the telephone’ is displayed.

60

Note

Select ‘Reset the telephone’. The display shows ‘Extension reset’ momentarily before returning to the Idle Menu.

If you are using a standard telephone, dial 739 and wait for the acknowledgement tone (internal dial tone).

Incoming Call Handling

General

Calls can be presented to the Mitel 1000 on CO lines and VoIP lines.

Calls can be programmed to ring any number of extensions. For configuration via the web interface, see page 94.


When calls are received on a line all free extensions, programmed to ring, are rung.

Any forwarding set on an extension are ignored for incoming calls unless the calls are routed to the extension by Caller ID programming or a caller has dialed through the Answering

Machine or a voice mail box. If a single phone is programmed to answer calls on a line the forwarding on the phone is acted on. If the phone has no forwarding set then the line forwarding is acted on. If more than one phone is programmed the forwarding options for the line are acted on.

Distinctive Ringing

This feature is primarily intended to support Fax. The Network Operator can provide a second number on a CO Line that rings with a different signal (teen line). See page 108 and 116 for distinctive ringing programming on the web application and page 164 for programming from the programming

Featurephone. The system is then programmed to ring an extension that can be equipped with a Fax machine when this ringing is detected. All calls with the normal cadence ring the extensions programmed in the Incoming ringing programming.

Restricting Outgoing Calls

This feature lets you decide which lines each extension can access for outgoing calls. By default, all extensions have access to all lines.



Day/Night Service

The ‘Day Service’ / ‘Night Service’ feature allows you to change the extensions which ring on incoming calls, change the Class of Service at each extension, and change the voice greeting heard by callers (if you have voicemail installed). These changes can take place automatically, at preprogrammed times daily, or can be invoked manually. Furthermore, the system can be programmed to remain in ‘Night Service’ over the weekend.



System Time/Date


61


Music on Hold Options

When an external call is placed on hold, you can choose between supplying music, a tone, or silence to the caller. The music source can be internal, in which case it is integrated into the system and cannot be changed, or external, in which case an external source must be connected to your system.



Hotline

Extensions can be programmed so that they automatically dial a number when they go off-hook. The number dialed can be an extension or an external number.



Assigning Extension Names

You may assign names to extensions. When an extension receives an internal call, its display will show the calling extension name in the place of the calling extension number.



Class of Service

Each extension may be programmed for a Class of Service. This determines the type of call the extension is allowed to dial. Four tables, which can be programmed with up to fifty codes, are used to implement six Classes of

Service:



Using Voicemail

Every extension can be allocated a voice mailbox. An Answering Machine facility is also available.

Voicemail

To allocate a Voice Mailbox to an extension



To turn on your Voice Mailbox



To access your Voice Mailbox

Press the MESSAGE Key.

Select ‘Voice Mail’.

Enter your extension number, (which is your voice mailbox number).

Enter your voicemail password, (1111 by default), followed by #.

62

Note

Note

You are presented with the voice mail menu. The options displayed are ‘Play’,

‘Erase all messages’, ‘Greeting’, ‘Change Password’, ‘Monitor’ and ‘Cancel’.

To retrieve messages left in your Voice Mailbox

If new voice messages have been left in your Voice Mailbox, the Message

Waiting Light, located on the top right-hand corner of your Featurephone, will be on. In addition, the top line on your Featurephone display will show ‘New voice messages’.

Select ‘New voice messages’.

Enter your extension number.

Enter your Voicemail Password, which is 1111 by default, followed by #.

Select ‘Play’. The new messages are played.

Each message is time stamped to tell you when the message was received. When all new messages are played, you are informed of the total number of messages in your box. You may skip the time stamp by dialing 8, which jumps forward ten seconds.

Forward a message from a Featurephone

A user can forward a message from their voice box to another voice box.

While you are listening to the message select the ‘Forward message’ option

Select the extension to forward to from the menu on the phone

In the forwarding voice box the forwarded message is considered as a message that has been heard by the user.

To automatically call the sender of a message

The ‘Return call’ feature allows a user to initiate a call to the sender of a message in their voice box.

When you have listened to a message in the Voicemail select the ‘Return Call’ option

The system initiates a call to that number

To return calls to external callers the Caller ID service must be available on the lines.

To record your own Voice Mailbox greeting:

Each extension, which has been allocated a Voice Mailbox, can record its own greeting. This will be relayed to callers who are answered by the Voice

Mailbox.

At your extension, press the MESSAGE Key.

Select ‘Voice Mail.

Enter your extension number when prompted.

Enter your Voicemail Password, (1111 by default), followed by #.

Select ‘Greeting’.

Select ‘Record greeting’

Speak to record a personalized greeting when prompted.

Press ‘Confirm’.

Press the Speakerphone Key to finish programming

63

To replay the Voice Mailbox greeting

At your extension, press the MESSAGE Key.




Select ‘Greeting’.

Select ‘Replay greeting’

The greeting will then be replayed for you.

Transferring calls to Voice Boxes

You can transfer calls to any Voice Box without calling the extension.

When you are on a call select 'Transfer to Voice Mail'

The menu is updated showing those extensions equipped with voice boxes.

Select the extension.

Select ‘Transfer’ or replace the handset.

For standard telephones the user should press the recall key and dial 710 followed by the extension number. Replace the handset.

To retrieve your Voice Mailbox messages remotely

In order to access your Voice Mailbox remotely you must have your calls

Forwarded to your Voice Mailbox, and have either a line programmed to ring directly at your extension.

You can also have your call transferred to your voice Mailbox.

If a line is programmed to ring directly at your extension and your Voice

Mailbox is turned on, dial the line number.

Call in on a line which you know will be answered and have the call transferred to your Mailbox.

When answered by your voicemail greeting, access your Voice Mailbox by dialing the code 711, followed by your extension number, Voicemail Password and #.

Then dial the following numbers to access your messages

While listening to the Greeting

Dial 1 Playback commences at the first message

Dial 2 For more information.

Dial 41 Turn remote notification on.

Dial 42 Turn remote notification off.

Dial 43 To program remote notification.

Dial 91 Change the outgoing greeting

Dial 92 Check the outgoing greeting

Dial 93 Delete the outgoing greeting

Dial 6 Erase all messages

Dial 0 Change Voicemail Password

When playback of messages has commenced

Dial # Playback is paused

Dial 2 Save this message and move to the next message

Dial 3 Erase this message and move to the next message

Dial 4 Go back to the start of the message

Dial 5 Go back to the previous message

64

Note

Dial 7 Go back ten seconds

Dial 8 Go forward ten seconds / Skip the time stamp

Dial 9 Forward the message to another extension

Dial 0 Return Call. Automatically make a call to the caller who left the message (this feature is not applicable when mailbox is accessed remotely).

To monitor/pick-up callers as they speak to your Voice Mailbox

You can operate your voicemail in Voicemail Monitor Mode. In this mode, when calls are forwarded to your Voice Mailbox and your extension is free, the call is relayed over the speaker of your Featurephone. If you lift your handset you can intercept the call in which case no message is left in the Voice

Mailbox.





Press the Scroll Down Key (Ô) until ‘Monitor’ is displayed.

Select ‘Monitor’.

Select ‘Monitor on’ or ‘Monitor off’.


To change your Voicemail Password

By default, each extension is allocated the same Voicemail Password, (1111).

You can enter your own password, which can be up to eight digits long, as follows:





Select ‘Change password’.

Enter your new Voicemail Password, which can be up to eight digits long.


Press the Hands-free Key to finish programming.

If you forget your Voicemail Password, you can check all extension Voicemail Passwords from the Programming

Extension.

To check all Voicemail Passwords



Remote Notification of Voice Messages

Extensions must be programmed to allow remote notification. See page 116 for programming from the Management Application and Page 172 for programming from the programming Featurephone.

When a user turns remote notification on, a call will be made to the personal or pager number programmed by the user to notify them that they have received a new voice mail message.

65

The user can set up remote notification to notify them of all new messages or only those marked as priority by callers to their voice mail.

Remote notification can be turned on and off as required.

If the call is to a personal number the user can access their voice mail when they answer the call by entering their voice mail password and pressing #.

Setting Up your Remote Notification to a Personal Number

You must first program the personal that the system is to call when a new message is received. Then select whether all messages or messages marked as priority are notified. Finally you turn remote notification on.

Programming a Personal Number

Press the MESSAGE key.

Enter your extension number (which is your voice mailbox number).

Enter your voice mail password (1111 by default) followed by #.

Select “Remote Notification”.

Select “Programming”.

Select “Personal Number”.

Select “Change”.

Enter the number.

From a standard or cordless telephone dial 4311 followed by the number to program a personal number.

Notification of All Messages or Priority messages






Select “Priority Messages Only” or “All Messages”.

From a standard or cordless phone dial 433 for priority messages and 434 for all messages.

Turning Remote Notification on and off





Turn remote notification on or off as required.

From a standard or cordless phone dial 41 to turn remote notification on and dial 42 to turn it off.

Setting up Remote Notification to a Pager

To program a pager to receive the remote notification call two numbers must be programmed, the number to contact the pager company and the digits that are sent to the pager company once they have answered the call (dial string).

Programming the pager number and the pager dial string






Select “Pager Number”.

Select “Change”.

Enter the number.

Press “Confirm”.

66

The menu updates to allow the dial string to be entered. Press “Change”.

Enter the digits required by the Pager Company.

Press “Confirm”.

From a standard or cordless phone dial 4321 to enter the pager number and dial string.

To operate voicemail from a standard telephone

Standard telephones can also be allocated Voice Mailboxes. When a Voice box is allocated the ‘Forward On No Answer’ is automatically set for the extension. You can set ‘Forward All Calls’ or ‘Forward when busy’ to the

Mailbox as well by setting the Forward to 710.

732 for ‘Forward all calls’

733 for ‘Forward when busy’

734 for ‘Forward on no answer’

Your telephone will be rung if any messages have been left in your own

Mailbox or the Answering Machine. If your extension is equipped with a phone that can detect Caller ID information an indication will be given on the phone that you have new voice messages. If your phone does not have Caller ID capability you should manually access your Voice Mailbox for messages.

To access the Voice Mailbox, dial the code 711, followed by your extension number, Voicemail Password and #. Then dial the following numbers to access your messages:

While listening to the Greeting

Dial 1 Playback commences at the first message

Dial 91 Change the outgoing greeting

Dial 92 Check the outgoing greeting

Dial 93 Delete the outgoing greeting

Dial 0 Change Voicemail Password

When playback of messages has commenced

Dial # Playback is paused

Dial 2 Save this message and move to the next message

Dial 3 Erase this message and move to the next message

Dial 4 Go back to the start of the message

Dial 5 Go back to the previous message

Dial 6 Erase all messages

Dial 7 Go back ten seconds

Dial 8 Go forward ten seconds / Skip the time stamp

Dial 9 Forward the message to another extension

Dial 0 Return Call. Automatically make a call to the caller who left the message.

Answering Machine

This feature allows you to set up the Answering Machine so that it can be turned on and off as required. You can also set the timer so that the answering machine answers calls immediately or after ringing for a period

You can select which lines are to be answered by the answering machine when it is turned on. It can be used on both CO lines and IP Trunks.

All messages received are stored in an answering machine, which is controlled by extension 20. Extension 20 can also customize the greeting.

67

You can turn the Answering Machine service on and off at any time at from any extension and its operation is independent of ’Night Service’.

You can use it if you are not answering calls at lunch or at night, or simply want to record messages from callers. If desired, you can have this feature on permanently, so that calls, which are not answered for a programmable period, are answered by the Answering machine. The greeting may ask callers to dial an extension number, in which case the call will be transferred through to that extension.

To program lines to be answered by the Answering machine



To turn the Answering Machine on and off

From a Featurephone select Answering Machine. At least one line must be programmed to be answered by the answering machine for the prompt to appear on the idle display.

From a standard or cordless phone dial 737.



To retrieve messages left on the Answering machine

Messages stored on the Answering machine can be retrieved from any extension. When messages have been left, the Message Waiting light on extension 20 will be lit and the ‘Ans/machine messages’ will appear on the top line of the display.

Select ‘Ans/machine messages’.

Enter 0 as the extension number.

Enter the Voicemail Password and select the option you require.

Extension 20 can have its own Voice Mailbox, accessed by using extension number 20. The Answering machine has its own Mailbox, accessed by using extension number 0. Both can have their own Voicemail Passwords.

To change the greeting on the Answering machine


Select ‘Voice messaging’.

Enter 0 as the extension number, (which is your Voice Mailbox number).


You are presented with the Voice Messaging Control Menu. The options displayed are ‘Play’, ‘Erase all messages’, ‘Greeting’, ‘Change Password’,

‘Monitor’ and ‘Cancel’.

Select ‘Greeting’.

Select ‘Record greeting’

Speak to record a personalized greeting when prompted.



To set the time a call will ring before the Answering machine answers


68

Note

Programming Additional System Options

Using a Doorphone

You can equip your Mitel 1000 with a Doorphone. The Doorphone has a button which, when pressed, rings at programmed extensions, and has a microphone/speaker for communication. With a Doorphone fitted in your reception area, anyone visiting your premises can call when they arrive and you can speak to them before you let them in.

Your Mitel 1000 also features a Doorstrike relay output, which can be used to operate a Doorstrike mechanism, to allow you open the door from your extension. You must purchase the Doorstrike mechanism yourself and arrange for a qualified electrician to install it.



Answering a Doorphone call

You can answer a Doorphone call if your extension is programmed to ring when someone calls at the Doorphone.

To answer a doorphone call, lift the handset and speak. There is no code to dial.

An extension cannot make a call to a doorphone

To open a door using the Doorstrike

When your extension is ringing with a Doorphone call, and you have a

Doorstrike mechanism installed, the option ‘Open the door’ will be displayed.

Select ‘Open the Door’. The Doorstrike relay will operate and the call to the

Doorphone will be disconnected.

From a standard telephone, the code is Hookflash731 if you are on a call and

731 if you are not.

External Forwarding Options

This allows you to decide if external callers or external and internal callers to your extension are forwarded externally. It also allows extensions to be prohibited from activating an external forwarding.


The Forward on no answer timer is set at 18 seconds in default.

This timer can be changed. See Page 111 for changing it via the

Management interface and Page 183 to change it via the programming systemphone


69

6

Connecting to the Internet

ADSL Modem configuration

The Mitel 1000 is configured with all the settings that will suit your ADSL

This section describes how to configure the way that your Mitel 1000 connects to the Internet. Your ISP determines what type of Internet access you should use and provides you with any information that you need in order to configure the Internet access to your Mitel 1000.

Your Mitel 1000 needs the following address information in order to access the Internet:

IP address and subnet mask:

Default gateway:

DNS servers:

The IP address and subnet mask assigned to your WAN interface.

The gateway address that identifies the

ISP server through which your Internet connection will be routed.

The Dynamic Name System (DNS) servers used by your ISP to dynamically assign addresses to each of the computers attached to your LAN.

In most cases, you will not need to configure your Mitel 1000 with these addresses because your ISP is likely to use an Internet access type, which automatically assigns addresses to your Mitel 1000.

Types of Internet Access

The other types of Internet access available are as follows:

PPP Internet access

– your Mitel 1000 uses a Point to Point Protocol (PPP) to carry data between your ISP and your computer. To use PPP Internet access, you must enter a PPP login username and password the first time to log on. The IP addresses required to access your ISP’s Internet service are automatically configured. Your Mitel 1000 supports two types of PPP –

PPPoE (over Ethernet) and PPPoA (over ATM).

DHCP Internet Access

– your ISP uses a protocol called Dynamic Host

Configuration Protocol (DHCP) to assign addresses and manage your Mitel

1000. The Mitel 1000 is automatically assigned the IP addresses that it needs to access the Internet.

Manual Internet Access

– you manually assign the addresses that your Mitel

1000 needs in order to access the Internet. Your ISP should provide you with the necessary addresses.

Configuring a PPPoA ADSL connection

If your ISP’s Internet service uses PPPoA you need to set up a PPP login account. The first time that you login to the Internet, your ISP will ask you to

70

enter a username and password so they can check that you are a legitimate registered Internet service user. Your Mitel 1000 stores these authentication details so you will not have to enter this username and password every time you login.

Your ISP may also tell you to set unique path and circuit numbers (called VPI and VCI) in order to connect your Mitel 1000 to the ISP’s Internet service. In most cases, your Mitel 1000 will use default settings, so you may not need to enter these values.

If your ISP wants you to connect to the Internet using PPPoA, follow the instructions below.

1.From the left-hand Setup menu, click on Router Configuration. The following page is displayed:

2. Click on ADSL Modem. The following page is displayed:

This page displays information about your current Internet access configuration.

Change the ADSL Modem settings here. The following page is displayed

71

Enter the PPP username and password provided by your ISP. Type them in the relevant boxes, and then click Next>.

5. The following page is displayed: The settings of VPI=0 and VCI=35 are the default settings. If your ISP has supplied you with different values enter them here.

Click Next>. The following page is displayed:

72

This page confirms your PPPoA settings.

6. If you are happy with your settings, click Confirm Changes. The Internet

Access page is displayed.

Configuring a PPPoE ADSL connection

If your ISP’s Internet service uses PPPoE you need to set up a PPP login account. The first time that you login to the Internet, your ISP will ask you to enter a username and password so they can check that you are a legitimate registered Internet service user. Your Mitel 1000 stores these authentication details so you will not have to enter this username and password every time you login.

Your ISP may also tell you to set unique path and circuit numbers (called VPI and VCI) in order to connect your Mitel 1000 to the ISP’s Internet service. In most cases, your Mitel 1000 will use default settings, so you may not need to enter these values.

If your ISP wants you to connect to the Internet using PPPoE, follow the instructions below.

1. From the left-hand Setup menu, click on Router Configuration. The following page is displayed:

2. Click on ADSL Modem. The following page is displayed:

73

This page displays information about your current Internet access configuration.

Change the ADSL Modem settings here. The following page is displayed

5. Enter the PPP username and password provided by your ISP. Type them in the relevant boxes, and then click Next>. The following page is displayed:

74

The settings of VPI=0 and VCI=35 are the default settings. If your ISP has supplied you with different values enter them here.

Note

Note

This page confirms your PPPoE settings.

7. If you are happy with your settings, click Confirm Changes. The Internet

Access page is displayed.

Enabling MAC spoofing

You should only enable MAC spoofing if your ISP has requested that you do so. In most cases, you will not need to do this.

Your ISP identifies your modem by its unique hardware number or Media

Access Control (MAC) address. If you are using PPPoE Internet access, your

ISP may want you to spoof the identity of a different device. You can spoof the

MAC address of another device by replacing your Mitel 1000’s existing MAC address with another device’s address. Your ISP will provide you with the replacement MAC address.

You can only configure MAC spoofing if you are using PPPoE

Internet access.

If your ISP instructs you to change your Mitel 1000’s default MAC address, follow the instructions below: the

here… The following page is displayed:

75

Enabled then click Next>. The following page is displayed:

Note

3. The MAC address is made up of six pairs of characters. Each character can be either a number between 0 and 9, or a letter between A and F. For example, 00:20:2b:80:2f:30. Click in each box and type each character pair of the MAC address provided by your ISP.

Click Next>. This page confirms your MAC spoofing settings. If you are happy with these settings, click Confirm Changes. The Internet Access page is displayed, and your MAC spoofing configuration is complete.

Configuring a DHCP ADSL connection – RFC 1483

If your ISP uses a DHCP DSL connection, your ISP may tell you to set unique path and circuit numbers (called VPI and VCI) in order to connect your Mitel

1000 to the ISP’s Internet service. In most cases, your Mitel 1000 will use default settings, so you may not need to enter these values.

Your ISP will provide you with the VPI/VCI values necessary to setup a DHCP DSL connection.

76

From the ADSL Modem: Types of Access page select DHCP , then click

Next>. The following page is displayed

Select the option as indicated by your ISP. The following page is displayed

Enter the VPI and VCI settings supplied by your ISP and select Next. The following page is displayed:

77

Note

The settings are shown. If you are happy with them press Confirm Changes.

Configuring a Manual Internet Connection – RFC 1483

If your ISP tells you to configure your Internet access manually, they must provide you with the following information:

The WAN IP address and subnet mask for your Mitel 1000

The Internet Gateway address

The primary and secondary DNS addresses

You should only change the Internet Access details if your ISP asks you to, or if you are familiar with network configuration. In most cases, you will not need to make any changes to this configuration.

1. From the ADSL Modem: Types of Access page Select Manual then click

Next>.

2.The following page is displayed: Click in each box and type the relevant address information provided by your ISP. Click Next>.

78

3. The following page is displayed: Select the Option provided by your ISP.

The following page is displayed:

4.Enter the VPI and VCI values supplied by your ISP

5. Click Next>. The following page is displayed:

79

This page confirms the address settings that you have manually configured

(the values displayed above are for example purposes only). If you selected the Manual option at step 5, the VPI and VCI values that you entered are also displayed on this page.

If you are happy with your settings, click Confirm Changes. The Internet

Access page is displayed and your configuration is complete.

ADSL Operating Mode

The ADSL operating mode controls how your device communicates with your ISP to provide Internet access. The default mode is Multimode will be compatible with a broad range of ISPs.

Click on ADSL Modem. The following page is displayed:

If you have difficulty connecting or are experiencing poor performance on the ADSL line you may need to change the mode of operation to make it compatible with your ISP. Consult your ISP before making any changes to the ADSL mode.

To change, click on Change the ADSL Modem operating mode here


80

required

Next.

The following page is displayed

If you are happy with these settings, click Confirm Changes

The Internet access page is displayed and your configuration is complete.

Connecting to an External ADSL Modem, Cable Modem, LAN,

WAN or add a host to the DMZ

The WAN/DMZ port can be used to connect to an external ADSL modem, a LAN or a WAN, or to add a host to the DMZ. screen is displayed:

81

screen is displayed

Three options are presented.

PPPoE, IP Gateway, DMZ.

PPPoE to connect to an external ADSL modem

PPPoE is used when connecting to an external ADSL modem. As the Mitel 1000 is equipped with an ADSL modem we recommend that the internal modem be used rather than an external ADSL modem. In this case go to ASDL Modem configuration on page 70.

If you wish to use the external ADSL modem proceed as follows:

2. The following screen is displayed: Enter a Username and

Password. Retype the Password. Select Next.

82

3. The following screen is displayed: Select Confirm Changes.

4. The following screen is displayed:

IP Gateway to connect to Cable Modem, LAN or WAN

IP Gateway is typically used when connecting to a Cable Modem

LAN or WAN.

Select IP Gateway. Select Next. The following screen is displayed:

Two options are presented: -

DHCP - automatically assigns IP addresses

Static - allows the IP addresses to be entered manually

DHCP

1. Select DHCP. Select Next. The following screen is displayed:

83

2. Select Confirm Changes.

Static

1. Select Static. Click Next. The following screen is displayed:

Enter the IP addresses and Subnet mask. Click Next. The following screen is displayed:

2. Select

84

DMZ

A host can be connected to the WAN/DMZ Port. In default the

Wan/DMZ port is configured as a DMZ. On the Router configuration page select WAN/DMZ Port. The following page is displayed:

Select Change the DMZ IP address here. The following page is displayed:

Enter the host IP address and subnet mask. Click Next. The following screen is displayed

85

Select Confirm Changes. The following screen is displayed

Note

The DMZ setup is now complete.

Password

You can restrict access to your Mitel 1000’s web pages using password protection. With password protection enabled, users must enter a username and password before gaining access to the web pages.

By default, password protection is enabled on your Mitel 1000, and the username and password set are as follows:

Username: admin

Password: admin

For more information, see Accessing the Web pages on page 22.

Setting your username and password

Non-authorized users may try to access your system by guessing your username and password. We recommend that you change the default username and password to your own unique settings.

To set your own username and password:

1. From the left-hand Router Configuration main menu, click on

Password in the sub-menu. The following page is displayed:

This page displays the current status of password protection.

86

is displayed:

3. This page allows you to enable or disable password protection.

Protection is already enabled by default. Click Next>. The following page is displayed:

4. This page displays the current username and password settings. Type your own unique username and password in the relevant boxes. They can be any combination of letters or numbers with a maximum of 20 characters. The default setting uses admin for both the username and password. We recommend that you do not set the same character combination for both username and password.

This page confirms that password protection is enabled and displays the username that will be required in order to access the web pages. If you are happy with these settings, click Confirm

Changes. The Enter Network Password login box is displayed. You need to login to the web pages using your new username and password. For details of how to do this, see Accessing the Web

pages on page 22.

87

Disabling password protection

If you do not want to use password protection, follow the instructions in ‘Setting your username and password’ on page 86 and at Step 3, select Disable and then click Next>. The following page is displayed.

DHCP Server

A DHCP (Dynamic Host Configuration Protocol) Server is a system that assigns IP addresses to the multiple stations on the network.

Dynamic Host Configuration Protocol is a scheme where a client host "leases" an IP address. This can be great on a large-scale network because it assigns an IP address, and many other options, such as DNS servers, WINS Servers, and other options.

Router Configuration from the main menu.

DHCP Server from the sub-menu. The following page is presented.

88

Enable/Disable

The DHCP server is enabled by default. It can be disabled if required. Select ‘Disable’ to disable DHCP.

DHCP Server Interfaces

By default the DHCP server operates on the iplan interfaces.

There is an option to delete DHCP on each interface. The DHCP

Server must be disabled before an Interface can be deleted.

Add new interface

There is an option to tell the DHCP server to operate on the ipdmz interface as well as the iplan.

89

Existing DHCP Server Subnets

The settings for the existing subnets on the iplan and ipdmz are displayed.

All displayed parameters can be changed – change the setting to a new value and click “Apply”.

To delete a subnet, check the associated box and select “Apply”.

Advanced Options

Select “Advanced Options”

The following screen is displayed

Parameters for this subnet

The current subnet parameters are shown. These can be changed if required.

IP addresses to be available on this subnet

The range of IP addresses available on the subnet is shown. These can be changed if required.

90

DNS Server option information

The default setting is use local host as the DNS server - all DNS requests are sent to the default gateway 192.168.1.1 which then relays the request to the DNS addresses negotiated at start up.

Specific DNS servers can be defined if required.

Default gateway option information

Use local host as default gateway is checked by default.

Additional option information

Select Create new DHCP option …


Select the option required from the drop down menu.

Default gateway

Domain name

IRC server

HTTP server

SMTP server

POP3 server

NNTP server

WINS server

Time server

Enter the option value in the field below.

Select OK

To create a new subnet

Select Create new subnet …

The screen displayed is the same as Edit DHCP server subnet with the Additional option information option.

To always assign the same IP address to a host

The same IP address is always assigned to a specific host with the specified MAC address.

Select “Create new Fixed Host …”


91

Note

Enter the IP address to be assigned to the host

Enter the MAC address of the host

Enter the maximum lease time in seconds

Select “OK”.

Addressing

The Addressing page displays information about your LAN IP address and allows you to change the address and subnet mask assigned to your Mitel 1000.

You should only change the addressing details if your ISP asks you to, or if you are familiar with network configuration. In most cases, you will not need to make any changes to this configuration.

Changing the LAN IP address and subnet mask

Select Router Configuration from the main menu.

1. From the submenu, click on IP Addressing. The following page is displayed:

This page displays the current IP address and subnet mask assigned to your Mitel 1000. The default LAN IP configuration is IP address 192.168.1.1, subnet mask 255.255.255.0.

92

on following page is displayed:

Note

3. Click in the IP Address and Subnet Mask boxes and type the new address details.

Your LAN PCs must remain on the same subnet as your Mitel

1000 (that is, the subnet masks must be the same) For more information about IP addresses and subnets, see IP Addresses on page 193. If necessary, reconfigure the LAN PCs so that their

IP addresses place them in the same subnet as the new Mitel

1000 IP address. See Configuring Ethernet PCs on page 201.

Note

5. This page displays the new IP address and subnet mask and asks you to confirm whether these are correct. Click Confirm

Changes. The Addressing page is displayed, confirming your new LAN address settings.

If you change the LAN IP address of the Mitel 1000 while connected through your Web browser, you will be disconnected.

You must open a new connection by entering your new LAN IP address as the URL. See Accessing the Web pages on page 22.

93

7.

PABX Configuration using the web interface

Your PABX (Phone System) can be completely configured via the web management system.

The web management Welcome page contain a link to Basic PABX

Settings, which are the configuration options that the user will most likely wish to change.

The Basic PABX Settings are:

Incoming Ringing

Extension Names

Outgoing Restriction

Extension Class of Service

Cordless Registration

Line Forwarding

Instruction for setting these basic options are given below.

Additional instructions are also included for all other PABX configuration options. These may be accessed by selecting PABX

Configuration from the main menu and then using the sub-menu below to access individual functions.

Some programming changes require the system to be restarted. A prompt, shown below, will appear on the left-hand side of the screen. The Restart must be selected before you exit to ensure the settings take effect.

Incoming Ringing

By associating lines with individual extensions, you can have lines ringing different extensions in Day and Night modes.

For example, in DAY mode, all calls on line1 might ring all phones, but in NIGHT mode all calls on line 1 might be set to only ring extension 20.

Also, in both DAY & NIGHT modes, all calls on IP Trunk (VoIP) 1 might be set to ring on extension 23 only.

94

To change the settings, select ON or OFF from the relevant drop down box for the Line/Extension configuration you require.

The default is that ALL lines ring ALL wired extensions and the first four cordless phones in both Day and Night Modes.

95

System Settings

Use this screen to program system wide settings for your system.

Activate Night Service

This feature allows the user to activate night service (normally outof-hours working). Night service set-up is used to define which extension rings on incoming calls, what the Class of Service is for each extension and what type of voice greeting is played.

The system operates in DAY MODE unless the night service option is specifically programmed to operate.


This turns the Answering Machine on and off. In default all incoming calls are forwarded on no answer to the answering machine.

However if you want to be able to activate the answering machine and turn it on and off firstly associate the answering machine with a line or lines (see page 107) and then turn the answering machine on. This can be done from a Featurephone or from this setting.

96

System VM Capacity

This setting determines the number of messages that may be stored in the answering machine.

Music on Hold Source

This options determines what a caller will hear when a call in placed on Hold.

Select the required option below from the drop-down box.

Silence

Tone

External – selects an external music source connected via an extension. See Music on Hold Extension, below.

Internal (Default – Internal system recording)

Answering Machine Password

The password can be between 1 and 8 digits long and can be any number between 1 and 99999999

This is the password used to access the system answering machine from extension 20.

Programming Password

The password is 4 digits long and can be any number between

0000 and 9999

This is the password used to access the programming functions on the system when using a Featurephone programming position

Store All Calls in the Caller ID Lists

Use this setting to determine what received calls are recorded by the system in the Caller ID Lists.

If set to OFF, only missed calls will be listed. If set to ON, all calls, including answered calls will be listed in the Caller ID lists.

Doorphone Enable

Use this to enable the operation of a Doorphone connected via the system.

Button Hopping

When Button hopping is enabled if you press a second line key while on a call on another line the first call is disconnected. With button hopping off the first call is placed on hold when the second line key is pressed.

Line Key Light

This allows you to have the line key light flashing or steady when a call is placed on hold. The default is flashing.

Night Services Start 1 (HHMM)

The time in 24-hour clock formats (HH:MM ) at which night service 1 is activated on the system.

Night Service End 1 (HHMM)

The time in 24-hour clock formats (HH:MM ) at which night service 1 is deactivated on the system.

97

Night Service Start 2 (HHMM)

The time in 24-hour clock formats (HHMM ) at which night service 2 is activated on the system.

Night Service End 2 (HHMM)

The time in 24-hour clock formats (HHMM ) at which night service 2 is deactivated on the system.

Music On Hold Extension

Select an extension position to connect to an external music-onhold source. The drop down menu displays all available extension positions.

Weekend Service

Weekend service is selectable as being ON or OFF. This renders the system operable in accordance with night service settings. To enable the option, select the relevant option. As long as the option is selected, the system will operate in accordance with night service programming parameters.

Barge-In Tone

Barge-In can be provided with or without a warning tone. The default is that tone is provided.

Automatic Line selection

When Automatic Line selection is turned on when an extension goes off hook and dials a free line is selected and the digits are sent to line. Internal calls are made by selecting the internal call menu on

Featurephone or by pressing hookflash and dialing the extension number.

98

System Speed Dials

You can dial your System speed dials from the relevant option on your Featurephone menu or by dialing the appropriate short code access from any analog phone.

This option allows the user to enter up to 99 System speed dial numbers, which will be available to all extensions. The System speed dials are referred to as Index 1 – 99.

You may also associate a Name with each Speed Dial entry.

Name

Enter up to 10 characters in this field

Number

Enter up to 20 digits in this field

To access the entries for Index 11 – 99, use the Next button on the bottom right hand corner of the Edit System Speed Dials page.

Note

WARNING

Make sure you select the APPLY button before proceeding to additional pages to complete more entries (e.g. Index 11 – 20), otherwise your changes might be lost.

Uploading System Speed Dials list

Alternatively, you may upload the System Speed Dials from a .CSV

(spreadsheet) file.

To do this, click Upload on the Edit System Speed Dials page and follow the instructions.

The file must be in .CSV format, with names in the first column, and phone numbers in the second column.

99

You can export files in this format using typical spreadsheet software, e.g. Microsoft Excel

Extension Settings

The settings on this page have an effect on an extension-byextension basis. Individual features can be set or unset for particular extensions on the system.

Basic Settings

Extension Name

You may assign names to extensions. When an extension receives an internal call, its 'display' will show the calling extension name in the place of the calling extension number.

To set the extension name, left mouse click on the field and enter the name associated with the extension

A maximum of 10 characters per name can be entered.

Voicemail

Use this setting to turn ON/OFF individual voicemail boxes for each extension.

100

Note


Select this option to edit Advanced Options for individual extensions.

Advanced Options for the cordless extensions contain only a subset of the below features, as some of the features are not relevant for cordless extensions.

101

Disconnect

Use this option to functionally disconnect the extension from the system (this option does not physically disconnect the extension).

Page Protection

When selected the extension in question will not receive pages from

Featurephones ‘Page-all’ calls.

Individual CLI store

You can program each extension to store five numbers each. Each of these extensions will have a separate record of calls that ring on

CO lines programmed to ring their extensions only.

Ringing Frequency

This option allows the ringing frequency to be changed from the default 25Hz to 50 Hz on individual extensions.

Reverse Cadence

Certain equipment connected to an extension position (such as answering machines) may not ring correctly when an incoming call is received.

This option allows the user to alter the incoming ringing cadence

(tempo) to facilitate such equipment.

Keypad confirmation

When Keypad confirmation is On a confirmation tone is heard when dialing from the keypad on the Featurephone.

Language

Three language options are available for he text prompts on the

Featurephone. These are English, French and Spanish. The default is English.

Hot Line


Left mouse click on the field and enter the hotline number associated with the extension. This is a telephone number up to 24 digits in length.

The user can enter another extension number, or an external number as required (include 9 to seize the outside line).

Not Allowed to Open the Door

The selected extension cannot be used to open the door when a call is placed over the doorphone.

External Forwarding

This option allows the administrator to enable or disable each extension’s facility to Forward calls to outside lines.

Selection range: Left mouse click on the field and a pull down list of options is displayed:

• No Trunk to Trunk (This setting means incoming external calls cannot be Forwarded back out on another external line)

• All Calls (Default: All call types (Internal & External) can be

Forwarded)

102

WARNING

• External Forward Only (This setting means that ONLY incoming external calls can be Forwarded externally)

It is possible that an extension may misuse the External Forward facility. The Default setting is that no extension is allowed to set the facility.

Note

Do Not Disturb

If your extension is set to ‘Do Not Disturb’, anyone trying to call you will receive a busy (engaged) tone. If the person trying to contact you has a Featurephone, ‘Do Not Disturb Enabled’ will appear on its

'display'. ‘Call Back’ and ‘Alarm call’ are the only incoming ringing that will be accepted when this feature is set.

Extensions may be set not to ring.

This option cannot be set for extension 20.

Lock Code

You use a Lock Password to lock, unlock, or to make calls from a locked extension. The default Lock Password for all extensions is

321, but each extension may change its password. Extension Lock

Passwords can be examined from the Programming Extension.

The allowable range is a three-digit code in the range 000 to 999.

Lock

This feature allows you to lock your extension to prevent unauthorized users from making external calls. Turn extension lock

ON or OFF.

Sys Sped Dial override

When this option is On extensions can dial all the numbers in the system speed dial list even if they are normally restricted from dialing that number.

Forward All

Before you leave your extension, you can Forward all your calls to ring at another extension. Alternatively, you can Forward all external calls presented to your extension to an external number.

This function can be set for all extensions

Left mouse click on the data entry field for each extension. Enter up to 24 digits in this field (include the trunk access digit of Forwarding to outside lines).

Note: Extension forwarding only applies to calls specifically to that extension. So, or example, calls routed to the extension as part of a general Incoming Ringing group will not be subjected to individual extension level Forwards.

Forward when busy

The ‘Forward when busy’ feature allows you to Forward all your calls to ring at another extension if your extension is busy

(engaged). Alternatively, you can Forward all external calls to an external number if your extension is busy. In this case, internal calls will not be Forwarded but will be given the busy tone.


103

Note

Forward on No Answer

The ‘Forward On No Answer’ allows you to Forward all your calls to ring at another extension if there is no answer at your extension after four rings. Alternatively, you can Forward all external calls to an external number if your extension has not answered after four rings. In this case, internal calls will not be Forwarded but will continue to ring your extension.


Left mouse click on the data entry field for each extension. Enter up to 24 digits in this field (include the trunk access digit of Forwarding to outside lines).

Broken tone will be heard at your extension until all call

forwarding is cancelled.

You cannot Forward to an extension that has the ‘Do Not Disturb’ feature set.

Voicemail Password

This is the password used to access individual extension voicemail boxes. By default, each extension is allocated the same Voicemail

Password, (1111). You can enter your own password, which can be up to eight digits long, as follows:

The password can be up to 8 digits in length.

Tone Protection

When on a call, the call waiting tone of conference tone is audible to the user. Where these tones are not required, the feature should be disabled.

Call Recording

This option allows the extension to record calls. When set the option to record the call appears on the Featurephone display when they are on a call. The extension must be allocated a voice mailbox for the feature to operate.

Able to Barge-In

This allows the extension to Barge-In on other extensions on a call.

Protect from Barge-In

Extension can be protected from being barged-in on by other extensions.

104

Personal Speed Dials

You can dial your personal speed dials from the relevant option on your Featurephone menu or by dialing the appropriate short code access from your analog phone.

This page allows the user to enter up to 30 personal speed dial numbers for each extension. The personal speed dials are referred to as Index 1 – 30.

Note

WARNING

You may also associate a Name with each Speed Dial entry.

Name

Enter up to 10 characters in this field

Number

Enter up to 20 digits in this field.

To access the entries for Index 11 – 30, use the Next button on

the bottom right hand corner of the Edit Personal Speed Dials page. You cannot Forward to an extension that has the ‘Do Not

Disturb’ feature set.

Make sure you select the APPLY button before proceeding to additional pages to complete more entries (e.g. Index 11 – 20), otherwise your changes might be lost.

Program Keys

This option applies to Featurephone only.

There are 8 programmable Function Keys on your system

Featurephone.

105

In default mode, the Featurephone ‘Program Keys’ are programmed to select the external lines available on the system, the first key for Line 1 the second for Line 2 and so on.

Note

Using your mouse left click on the ‘Function’ menu option next to the Key you wish to program. From the drop down list available, select the required setting.

Some settings require additional data to be entered. e.g.

Selecting "Extension" as the program function will require you to enter the actual extension number (e.g. 21, 32 etc..) in the associated ‘Number’ field.

106

Line Settings

The settings on this page have an effect on a line-by-line basis.

Individual features can be Enabled or Disabled for particular lines that are connected to the system.

Equipped

The system assumes that available line interfaces have external lines connected to them. If a line interface does not have an exchange line connected, ensure correct system operation by unequipping the line interface in system programming

Select this option to enable/disable lines connected to the system.

Setting the option to Off, disables the specified line.

Outgoing Group

Lines can be grouped together in up to 2 Outgoing Groups.

Each Outgoing Group is associated with a code. These codes are

9 and 8, with Group 1 being associated with 9, and Group 2 with 8.

Dialing a code selects a line from the associated Outgoing Group.

This option allows you to select the required Group for the selected line.

Use Answering Machine

This feature allows you to set up an answering machine to answer incoming calls. You can select which lines are to be answered by the answering machine when it is turned on.

All messages received are stored in the answering machine.

You can use it if you are not answering calls at lunch or at night, or simply want to record messages from callers. If desired, you can have this feature on permanently, so that calls, which are not answered for a programmable period, are answered by the answering machine. The greeting may ask callers to dial an extension number, in which case the call will be transferred through to that extension.

Select this option to answer incoming calls on the line with the answering machine.

107


Dial Tone Detect

This option requires the system to detect dial tone before calls can be made.

If set to FALSE, this feature prevents the system from dropping the line when dial tone has not been detected.

In this case, the line is released if no digit is dialed until the expiration of a timer.

Caller ID Detection

This option enables the system to detect incoming Caller ID information received from the network and to display it on

Featurephone.

Long CO Line

In some situations if the transmission on the CO Line is poor it may be necessary to change this setting, which changes the impedance presented to the line.

Distinctive Ring

If the distinctive ringing facility is required it is turned on here. See page 61 for a detailed description of the facility.

Line Forwarding

You can use this feature to Forward (On Busy, No Reply or All

Calls) calls received on a particular line to an extension or an answering machine.

108

Because extension level forwarding only applies for calls dialed to specific extension, this feature allows you to control how to forward calls, which are received on particular lines and are not destined for a particular extension using Caller ID routing.

This feature also solves the issues of which extension’s forwarding setting would take precedence in the event of an incoming call ringing multiple extensions with different Forwarding options defined.

For each incoming line (Line 1 and 2, IP Trunk 1 & 2) you can define what number to forward the call to for the cases of No Reply,

Busy & All Calls.

(See also PABX Configuration -> Extension Settings -> Advanced

Options)


The Class of Service feature allows the user to define restriction settings for each extension connected to the system prohibiting the extension from making certain types of call.

The following restrictions can be defined per extension:

No Restrictions i.e. All calls are allowed

Restrict International i.e. Prevent the extension from dialing calls beginning with the codes you enter in the International table

Local Only i.e. Prevent the extension from dialing codes you enter in the International AND National tables

Emergency Calls Only i.e. (911, 060, 066, 080, 100, 101, 105, 106,

107, 110, 112, 115, 116, 118, 119, 123, 127, 128, 131, 132, 133,

156, 171, 190, 191, 192, 193, 194, 197, 198, 199, 211, 311, 511,

912, 913, 990, 999).

The extension can only dial Emergency Numbers. All other codes are restricted

By default ALL extensions can dial ALL destinations.

Select the required setting for each extension from the relevant drop-down box.

109

By default ALL extensions can dial ALL numbers.

The Allowed and Restricted Codes

The Allowed & Restricted codes can be used to add greater flexibility to how you can configure the settings.

For example, if you wanted to restrict all International calls, except those to the UK (international code 01144...). In this case place the extension in Restrict International in the Class of Service settings, and then set Allowed Codes to ON for the extension in question.

In the International table enter 011 in Index 1 and in the Allowed

Codes list enter the dialing code for the UK (01144). These settings allow the caller to dial 01144 but restricts all other 011 codes.

Similarly if you want restrict particular numbers enter them in the

Restricted Codes list and set the Restricted Codes to on for the extension.

Note

If 'Emergency Only' is set, Allowed and Restricted codes have no effect.

Day and Night Mode

There are different settings for Day Mode and Night Mode. To configure Day/Night mode see PABX Configuration -> System

Settings.

110

Timers

The timers listed below are under the control of the user and therefore can be changed from the default setting, provided the new settings is within the individual timers limits.

Recall On Hold

This is the time that elapses before a call, which has been placed on hold, rings back the extension that put the call on hold.

Recall On Transfer

This is the time that elapses before a call, which has been transferred and not answered, rings back the extension that attempted the transfer.

Forward On No Answer

This is the time that elapses before a call ringing at an extension, with ’Forward On No Answer’ set, is forwarded.

External Forward

This sets the time in minutes before an externally forwarded or transferred call is automatically cleared down.

Open Door

This is the time that the Doorstrike relay will remain open following activation.

Doorphone Ring Duration

This is the time that extensions will ring when the Doorphone is pressed.

Call Park

This is the time that elapses before a call placed on ‘Call Park’ rings back the parked call extension.

111

Ring Back Time

This is the time an extension will ring when Ringback has been invoked.


This is the time that elapses before an unanswered incoming call is presented with the System voice mailbox greeting.

Voice Mail Message Length

This is the maximum length of a message left in a Mailbox or a

Greeting for a Mailbox, Auto Attendant or Courtesy service.

Remote Notification Delay

This is the delay between receiving a message in a voice mailbox and setting up the remote notification call.

Remote notification Interval

This is the interval before setting up a second call if the first one was unsuccessful.

LCR Programming

This feature can be used to ensure that certain calls are routed over specific lines, or over a specific network provider, typically to take advantage of optimal call charges for specific call types.

Edit LCR Programming

To set up the feature you associate dialed digits (Input Codes) with the lines over which calls should be routed and with whatever network codes (Output codes) are necessary to route the call.

For example, if you wished all International (Input code = ‘011’) to be routed over IP Trunk 1, then you would associate Input Code

‘011’ with IP Trunk 1

In addition, you may choose to route the calls over different lines at various times of the day for optimum call rates.

The feature can be turned on permanently or activated at particular times.

Once the facility is activated, calls are automatically routed over the selected lines, and the network code (Output Code) is dialed automatically on the line before the telephone number.

Use this Edit LCR Programming Page to Enable/Disable LCR service and to set Start Times & Stop Times for service activation.

To configure additional LCR parameters, see ‘To enter the dialing codes and line selection, click here.’ on the Edit LCR Programming page.

112

Edit LCR Codes

Using this page you may define the Least Cost Routing criteria.

Up to 30 LCR rules may be defined (Index 1 – 30).

In the ‘Input Code’ field you insert the relevant dialed digits (e.g. ‘00’ for International calls or ‘001’ for International calls to the USA).

In the Output Code field, you insert whatever digits you want to be passed to the network. If no additional carrier access codes are required, then the Output Code is the same as the Input Code.

If you require to enter an network operator specific access code enter this before the relevant dialed digits in the ‘Output Code’ field.

The ‘Output Code’ entered will be dialed automatically by the system on front of the user dialed digits.

Preferred On/Off

In Preferred On is selected (Preferred Mode), then the system will, as a preference, route the call using the line(s) which have been enabled for each specific Input Code. However, if these line(s) are busy or not-available, then the system will attempt to route the call over any of the remaining system lines (i.e. those, which are not enabled for that specific Input code)

LCR Lines

For each specific LCR rule (Index), enable which lines are available for selection.

CLI Routes

Using this feature, incoming calls from particular numbers (Caller

Identities – CLI) can be associated with a particular name and routed to a pre-defined extension.

113

Note

In the number field, enter the callers number (CLI) as is delivered by the network. You may choose to associate a name with this number.

Select the extension to be rung when this number is detected..

Options for Day & Night routing exist. To set the system Day &

Night mode times see PABX Configuration -> System Settings.

Up to 30 individual entries can be made, referred to as Index 1- 30.

To access the entries for Index 11 – 30, use the Next button.

If no name is entered for the incoming CLI, the system will compare the incoming CLI against the speed dial list to match for a name.

Outgoing Restriction

Use can use this feature to restrict an extension from being able to make outgoing (external) calls on particular lines

Configure the restriction for each line separately, i.e.

Turn OFF for those extensions that are not allowed to select the particular line to make outgoing calls.

114

Local Codes

The Caller ID number presented from the network is the 10 digit national number. It does not include the 1 that is required for toll calls. The system must be able to distinguish between local and toll numbers so that they can be correctly dialed from the Caller ID stores.

This is achieved by entering the local codes in the Local Codes table.

When a number is received, the local area code is compared to the codes entered in the Local Codes table. If the digits do not match, the digit 1 is added as the toll access digit and the number, including the leading 1, is stored in the Caller ID store.

If there are two or more local codes programmed in the Local

Codes table then the 10 digit local number is stored and dialed for local calls.

If there is only one local code programmed in the Local Codes table then the area code is stripped and the 7 digit local number is stored and dialed.

Up to forty 6-digit codes can be programmed.

115


This feature is primarily intended to support Fax. The Network

Operator can provide a second number on a CO Line that rings with a different signal. The system is then programmed to ring an extension that is equipped with a Fax machine when this ringing is detected. All calls with the normal cadence ring the extensions programmed in the Incoming ringing programming.

Select those extensions to ring when the second ringing signal type is detected on the line. Different extensions can be selected when the system is in day or night mode.

Remote Notification

The various settings for remote notification of voice mail messages are set here.

Set ‘Allowed’ on for those extensions allowed to activate remote notification.

When ‘Activated‘ is set to On the remote notification is activated for the extension. The extension can activate and deactivate the feature from within their own voice mailbox.

116

The notification type can be set to all messages or priority messages only. The user can also set this from within their voice mailbox.

The notification method is whether the notification is to a normal telephone or a Pager Company. This can also be set by the extension.

Select ‘To enter additional Remote Notification settings click here’

Enter the personal number if remote notification is to a telephone number

Enter the Pager Company number and the Pager dial string if notification is to a pager company

Also three delays are provided between the call to the Pager

Company being answered and the pager string being dialed. This is set at a short delay.

There are a number of systemwide settings, which cannot be set by individual extensions. These are accessed by selecting ‘To enter

the systemwide settings click here’

The number of simultaneous calls determines the number of remote notification calls that will be set up at the same time.

117

The number of retry attempts sets the number of times the system will try to set up a call if it is not successful

The line group selects the lines that will be used for the calls.

118

8.

Advanced Router Settings

VoIP Settings

VoIP (or Voice over Internet Protocol) is a way to make and receive phone calls using your broadband Internet connection instead of your standard phone line. Mitel 1000 converts your phone calls into data that is sent over your high-speed Internet connection.

Basic VoIP Settings

In order to register with your VoIP service providers you will need to configure your system with your account details.

Your VoIP service providers should provide these to you.

2 VoIP channels (IP Trunk 1 & 2) can be configured simultaneously.

Select VoIP setup.

The current VoIP settings are displayed.

Note

No VoIP trunks are configured. Also the SIP User domain, SIP

Registrar proxy or Outbound server are not set. This information is supplied by your VoIP service provider

Select Change VoIP settings here

119

Username

Use this field to enter the SIP username as supplied by your VoIP service provider.

The endpoint name may be any alphanumeric string of up to 50 characters.

Password

Use this field to enter the SIP password as supplied by your VoIP service provider.

The endpoint password may be any alphanumeric string of up to 50 characters.

Register

Select/Deselect this Check Box to Enable/Disable the particular

VoIP account.

Advanced VoIP Settings

Your system uses Session Initiation Protocol (SIP), an internationally recognized standard for implementing Voice over

Internet Protocol (VoIP).

You should have registered with your VoIP service provider for a

SIP account.

Select Change Advanced VoIP settings here

120

Definition

Definition

User Domain

The User Domain of the VoIP Service Provider is the domain name is a SIP address. The SIP user domain may be a fully qualified domain name.

For example, if the SIP address is given as 123456789@voip-

provider.com, then voip-provider.com is the User Domain.

Registrar Server Proxy

The SIP registrar server proxy may be a fully qualified domain name or any valid IPv4 address. It specifies the address of the SIP registrar proxy server.

Registrar Server Port

The registrar server port may be any value between 1 and 65535. It is the port used by the SIP proxy server.

Registrar Server Expiry Time

The SIP registrar server expiry time interval can be any number between 1 and 86400. The timer is in seconds, and sets the frequency with which Mitel 1000 refreshes its registration with the

SIP proxy server.

Transport for Invite Requests

The transport for SIP invite requests may be either TCP or UDP

Preferred Codec

The following codecs are supported on the system:

• G.729

• G.711

• G.726.

A Codec (Coder/Decoder) converts analog voice signals into digital signals for transmission over the IP network.

Use this field to select the type of voice codec that you want the system to use. The choice of voice codec is a trade-off between transmission speed, sound quality and desired bandwidth usage.

The G.711 codec provides higher voice quality than G.729 but requires 82.8kbps of bandwidth as opposed to 26.8kbps for

G.729. The system can connect to other VoIP systems that use the same codec.

Backup Codec 1

This field specifies the first backup codec to use in the event that the far end does not support the Preferred Codec.

Backup Codec 2

This field specifies the second backup codec to use in the event that the far end does not support the Backup Codec 1.

About Quality of Service (QoS) Differentiated Services Code

Point (DSCP) is a field in an IP packet that enables different levels of service to be assigned to network traffic. This is achieved by marking each packet on the network with a DSCP code and appropriating to it the corresponding level of service or

121

priority.

If supported, the DSCP QoS can give you a better quality connection by using the DSCP QoS field to increase the priority for your traffic.

QoS: RTP DSCP

This field sets the DSCP code to be used for voice/payload (RTP) traffic in your VoIP call.

QoS: Signaling DSCP

This field sets the DSCP code to be used for signaling traffic in your

VoIP call.

Outbound Server

This field sets the name of the Outbound Server.

Outbound Server Port

This field sets the Outbound Server Port.

Outbound Server Transport

This field sets the type of the Outbound Server transport used.

Wireless Setup / Security

This chapter assumes PCs are already equipped with a wireless card.

The Wireless Network page allows you to configure the Wireless features of your Mitel 1000.

From the left-hand Setup menu, click on Wireless Setup / Security.


To enable the wireless network Select Enable or disable the wireless network here...

in the General Settings

122

Select Enable and Next.

The following page showing the Wireless Network name is displayed

Your Mitel 1000 and all of the wireless PCs in your wireless LAN share the same wireless network name. This name (commonly known as the Service Set Identifier (SSID)) distinguishes your

Wireless network from any other(s) that may be in use nearby. It also ensures that only those PCs configured with the same name as the one set on your Mitel 1000 can obtain access to it.

For security reasons, we recommend that you replace the default network name with a unique value of your own.

To do this:

1. Click in the Network Name (SSID) box and type a new name.

The name can be any combination of numbers and/or letters with a maximum length of 32 characters.

Click Next>.

The next page in the wizard sequence is displayed, which allows you to Select a Channel.

Your Mitel 1000 and all of the wireless PCs in your wireless LAN must share the same channel number. Each channel represents a regulatory channel frequency (MHz). Some countries may regulate the use of certain channel frequencies. Your ISP determines which channels are available and whether you should allow automatic or manual channel selection.

To configure channel selection, choose one of the following options:

123

If you want the Mitel 1000 to automatically select the best channel for your network, click on the Allow Mitel 1000 to select channel option and then click Next>.

If you want to manually select a channel, click on the Select a channel manually option and then click Next>. The following page is displayed:

Select a suitable channel (as advised by your ISP) from the

Channel drop-down list and then click Next>.

124

Configure Wireless Network Security

The following page allows you to configure wireless security:

You can protect your wireless data from potential eavesdroppers by encrypting wireless data transmissions. An eavesdropper might set up a compatible wireless adapter within range of your Mitel 1000 and attempt to access your network. Data encryption is the translation of data into a form that cannot be easily understood by unauthorized users.

There are two methods of wireless security to choose from:

Wired Equivalent Privacy (WEP); data is encrypted into blocks of either 64 bits length or 128 bits length. The encrypted data can only be sent and received by users with access to a private network key.

Each PC on your wireless network must be manually configured with the same key as your Mitel 1000 in order to allow wireless encrypted data transmissions. Eavesdroppers cannot access your network if they do not know your private key. WEP is considered to be a low security option.

Wi-Fi Protected Access (WPA); provides a stronger data encryption method (called Temporal Key Integrity Protocol (TKIP)). It runs in a special, easy-to-set-up home mode called Pre-Shared Key (PSK) that allows you to manually enter a pass phrase on all the Mitel

1000s in your wireless network. WPA data encryption is based on a

WPA master key. The master key is derived from the pass phrase and the network name (SSID) of the Mitel 1000.

To configure security, choose one of the following options:

If you do not want to use Wireless Network security, click the Off radio button and then click Next>. Off is the default setting, but you are strongly recommended to use wireless network security on your Mitel 1000.

If you are following the First Time Settings wizard, the next page in the wizard sequence is displayed, which allows you to Configure

Wireless Address Authentication.

If you have accessed this page from the General Settings section of the Wireless Network page, click on the Confirm Changes button to apply changes and return to the Wireless Network page.

If you want to use WEP 64bit data encryption, click on the 64bit encryption on the wireless network radio button and then click

Next>. Now follow the instructions in Configuring 64bit or 128bit encryption on page 126.

125

If you want to use WEP 128bit data encryption, click on the 128bit encryption on the wireless network radio button and then click

Next>. Now follow the instructions in Configuring 64bit or 128bit encryption on page 126.

If you want to use WPA, click on the Wi-Fi Protected Access (WPA) on the wireless network radio button and then click Next>. Now follow the instructions in Configuring WPA security on page 127.

Disabling the Broadcast of the SSID Network Identifier

For additional security you can disable the broadcast of the Network

Identifier, SSID. Unticking the Enable SSID Broadcast button on the

Wireless security page does this. To connect to a network that is not broadcasting the SSID it is necessary to enter the SSID manually in the network connection properties in the Control panel of your PC.

Configuring 64bit or 128bit encryption

The example set in this section is for 128bit encryption, however the outline also applies to 64bit encryption.

1. Once you have selected your WEP encryption method and then clicked Next>, the following page is displayed:

Note

2. Click in the Key box and type a unique 26-character hex network key, such as A6F34B2CE5D68BE90A6F34B2CE.

Hexadecimal or ‘hex’ numbers each have a value of 0 to 9 or A to

F. Each number represents four bits of binary data.

Note that if you selected 64bit, you will need to type a unique 10character hex network key.

If you are following the First Time Settings wizard, the next page in the wizard sequence is displayed, which allows you to Configure

Wireless Address Authentication.


126

Configuring WPA security

Once you have selected WPA and then clicked Next>, the following page is displayed:

WARNING

1. Type a unique pass phrase in the Pass phrase text box. Your pass phrase should be at least 20 characters long in order to deter potential intruders.

2. Once you have typed a pass phrase, click Next>.

If you are following the First Time Settings wizard, the next page in the wizard sequence is displayed, which allows you to

Configure Wireless Address Authentication.


It is strongly recommended that you enable Wireless Security to help protect your wireless network from unauthorized access.

Select a Channel

The following page allows you to select a network channel:

The next page in the wizard sequence is displayed, which allows you to

127

Configure Wireless Network Security.


Configure Wireless Address Authentication

The following page allows you to configure which wireless PCs can access the Mitel 1000:

By default, any wireless PC that is configured with your network’s

SSID and channel number can connect to your Mitel 1000. You may want to increase the security of your wireless network by creating one of the following lists of wireless PCs:

A wireless PC blacklist; PCs on this list cannot access the Mitel

1000, but all other wireless PCs can.

A wireless PC whitelist; PCs on this list can access the Mitel 1000, but all other wireless PCs cannot.

The Wireless PCs added to either list are identified by their unique

MAC address. This is made up of six pairs of characters, with each character either a number between 0 and 9, or a letter between A and F. For example, 00:20:2b:80:2f:30.

To configure which wireless PCs can access your Mitel 1000, choose one of the following options:

If you want any wireless PCs to have access to your Mitel 1000, click on the Allow any wireless PCs to connect radio button. Click

Next>.

If you are following the First Time Settings wizard, the final page in the wizard sequence is displayed, which allows you to Confirm

Wireless network changes.

If you have accessed this page from the General Settings section of the Wireless Network page, click on the Confirm changes button to apply changes and return to the Wireless Network page.

If you want to create a blacklist of PCs that cannot access your Mitel

1000, click on the Allow all wireless PCs to connect except those I specify radio button and then click Next>. Now follow the instructions in Configuring the wireless PC blacklist on page 129.

If you want to create a whitelist of PCs that can access your Mitel

1000, click on the Only allow the wireless PCs I specify to connect radio button and then click Next>. Now follow the instructions in

Configuring the wireless PC whitelist on page 130.

128

Configuring the wireless PC blacklist

1. Once you have selected Allow all wireless PCs to connect

except those I specify radio button and then clicked Next>, the following page is displayed:

2. To add a network PC to the blacklist, click Add an address


3. Click in each box and type each character pair of the MAC address for the PC you want to blacklist. Click Next>. The following page is displayed, containing details of the MAC address that you have just added:

4. This page allows you to configure the addresses on the blacklist:

If you want to add another MAC address to the blacklist, click Add an address here… and repeat the instructions described in step 3.

If you want to remove a MAC address from the blacklist, click

Remove an address here… At the displayed page, select the MAC address that you want to remove from the drop-down list.

129

If you are following the First Time Settings wizard, the final page in the wizard sequence is displayed, which allows you to Confirm

Wireless network changes.


Configuring the wireless PC whitelist

1. Once you have selected Only allow the wireless PCs I specify

to connect radio button and then clicked Next>, the following page is displayed:

2. To add a network PC to the whitelist, click Add an address


3. Click in each box and type each character pair of the MAC address for the PC you want to whitelist. Click Next>. The following page is displayed, containing details of the MAC address that you have just added:

4. This page allows you to configure the addresses on the whitelist:

If you want to add another MAC address to the whitelist, click

Add an address here… and repeat the instructions described in step 3.

If you want to remove a MAC address from the whitelist, click

Remove an address here… At the displayed page, select the

MAC address that you want to remove from the drop-down list.

If you are following the First Time Settings wizard, the final page in the wizard sequence is displayed, which allows you to

Confirm Wireless network changes.

130

If you have accessed this page from the General Settings section of the Wireless Network page, click on the Confirm

Changes button to apply changes and return to the Wireless

Network page.

Confirm Wireless network changes

Once you have configured Wireless Address Authentication and clicked on Next>, the following page is displayed:

Note

This page confirms the configuration changes made to each page in the wizard. If you are happy with these settings, click on the Confirm

Changes button. Configuration changes are applied to the Mitel

1000 and the Wireless Network page is displayed.

Once you have completed the First Time Settings wizard, you can edit specific wireless settings using the hyperlinks displayed in the

General Settings section of the Wireless Network page.

Wireless Network First Time Settings Wizard

This section describes how to follow the wireless network wizard in order to configure your wireless network settings for the first time.

The wizard sequence allows you to configure each of the following

Wireless settings in order:

The country that your network is operating in

The specification standard used by the wireless network

The wireless network name

The wireless network channel

Wireless network security

Wireless network address authentication

Each page of the wizard contains a Cancel button. Click on this if

you want to exit the wizard at any time.

Setting the Country

the page, click Change your wireless first time settings here… The first page of the wizard is displayed:

131

The number of valid wireless network frequencies varies from country to country and you need to identify which country you are operating the Mitel 1000 in to ensure that your network will transmit on the correct frequency. The setting for the USA is the default setting so you do not need to change it. the country. Click on the Confirm Changes> button to apply configuration changes and move on to the next page in the wizard sequence, which allows you to Select your Wireless

Network Type.

Select your Wireless Network Type

The following page allows you to select the Institute of Electrical and

Electronics Engineers (IEEE) specification supported by your network:

Each specification transmits at a certain speed (measured in Mbits per second) over a specific frequency. The frequency indicates the range at which wireless traffic can be transmitted or received between the Mitel 1000 and the wireless PC(s).

Supported specifications are:

802.11B only – provides slower rates at a longer range than

802.11G (11 Mbps in the 2.4 GHz band)

802.11G only – provides faster rates at a shorter range than

802.11B (20+ Mbps in the 2.4 GHz band)

802.11B/G – supports both of the above specifications, but 802.11G rates will be slower than they are in a G-only network

To select a network type, click on a single radio button.

Click on the Confirm Changes> button to apply the configuration changes.

132

Wireless Network General Settings

The General Settings section of the Wireless Network page displays details of the Mitel 1000’s current wireless configuration. For example:

The hyperlinks in this section allow you to:

Enable/disable wireless networking; see page 122.

Change the channel currently in use; click Change your wireless channel here… and follow the instructions in Select a Channel on page 127.

Change the network name (SSID); click Change your wireless

network name here and follow the instructions in on page 122.

Configure wireless security; click Change Wireless Security settings here… and follow the instruction in

133

Configure Wireless Network Security on page 125.

Configure address authentication; click Change which wireless PCs are allowed to connect here… and follow the instructions in

Configure Wireless Address Authentication on page 128. display information about the wireless PCs connected to the Mitel

1000; see Displaying details of Wireless PCs on page 134.

Displaying details of Wireless PCs

At the Wireless Network page, click on View details of connected

wireless PCs… The following page is displayed:

This page displays the MAC address of the PC currently connected to your Mitel 1000, together with the signal strength. The signal strength is the measure of radio frequency (RF) energy detected by the Mitel 1000 on a specific channel. Signal strength may vary depending on the position of the PC(s) in relation to the Mitel 1000.

To return to Wireless Network page, click on Return to the wireless

status page.

134

WAN

Firewall

The Mitel 1000 is equipped with a stateful inspection firewall.

The firewall resides on the interfaces between

- WAN and LAN (External and Internal)

- WAN and DMZ (External and DMZ)

- DMZ and LAN (DMZ and Internal)

F/W

LAN

F/W F/W

DMZ

From the left-hand Setup menu, click on Network security. The following page is displayed:

Select Firewall. The following screen is displayed


135

Security State

The Firewall is disabled by default

Intrusion Detection is disabled by default.

To enable the Firewall

To enable Intrusion Detection

“Enabled”

Security Level

There are three pre-defined security levels (high, medium, and low) that contain different security filters for each interface (WAN/LAN,

WAN/DMZ, DMZ/LAN). There is a fourth option called None, which is a blank firewall configuration that provides no security. Additional filters can be added to each security level. The default setting is

High

The pre-defined security configurations are:

High Security Level

WAN

<>

LAN

WAN

<>

DMZ

DMZ

<>

LAN

HTTP TCP 80 N Y Y Y N Y

DNS UDP 53 N Y Y Y N Y

Telnet TCP 23 N Y N Y N Y

SMTP TCP 25 N Y N Y N Y

POP3 TCP 110 N Y N Y N Y

FTP TCP 21 N Y N Y N Y

ICMP N/A N/A N Y N Y N Y

SSH TCP 22 N Y Y Y N Y

136

5060

6000

Y Y N Y N Y

Medium Security Level WAN

<>

LAN

WAN

<>

DMZ

DMZ

<>

LAN

HTTP TCP 80 N Y Y Y N Y

DNS UDP 53 N Y Y Y N Y

Telnet TCP 23 N Y N Y N Y

SMTP TCP 25 N Y Y Y N Y

POP3 TCP 110 N Y Y Y N Y

FTP TCP 21 N Y N Y N Y

ICMP N/A N/A N Y N Y Y Y

SSH TCP 22 N Y Y Y N Y

Low Security Level WAN

<>

LAN

WAN

<>

DMZ

DMZ

<>

LAN

TCP 65535 N Y N Y N Y

HTTP TCP 80 N Y Y Y Y Y

DNS UDP 53 N Y Y Y Y Y

Telnet TCP 23 N Y Y Y Y Y

SMTP TCP 25 N Y Y Y N Y

POP3 TCP 110 N Y Y Y N Y

FTP TCP 21 N Y Y Y Y Y

ICMP N/A N/A N Y Y Y Y Y

SSH TCP 22 N Y Y Y Y Y

Changing the security level deletes the previous security level and any filters set and replaces them with the new configuration.

To change the security level

1. Select the required level from the drop-down menu

NAT (Network Address Translation)

NAT is enabled by default on the three interfaces.

To disable NAT

From the main Firewall page select the option required

137

Select “Disable NAT to … (Interface)”

Restart the Mitel 1000 for the change to take effect

Global Address Pools

A range of external IP addresses can be assigned to a specific interface.

Select “Advanced NAT Configuration …”


Select “Add Global Address Pool …”

The following screen is displayed.

138

Select an interface from the drop down list

Enter an IP address and subnet mask, or enter the first and last IP addresses in the range

Select “Add Global Address Pool”

Reserved Mappings

Static routes can be defined between an external IP address and internal IP addresses.

Select “Advanced NAT Configuration …”

Select “Add Reserved Mapping … ”


Enter the following parameters:

Global IP address This is the public IP address assigned to the

WAN interface

Internal IP

Address

This is the internal IP address of the server on the LAN

Transport Type

External Port

Range

Select a protocol from the drop down list

A port or port range can be defined for the external IP address

Internal Port

Range

A port or port range can be defined for the internal IP address

Select “Add Reserved Mapping”

139

Policies, Triggers, Intrusion Detection, Logging

The security policy settings, stateful inspection triggers, intrusion policy detection and logging settings can be displayed and changed.

Security Policy

This is used to add or delete filters

Select “Security Policy Configuration …”

The following screen is displayed.

Select “Port Filters … ” for an interface (external/internal, external/dmz, dmz/internal)

The following screen is displayed for the interface selected

This screen lists the filters currently in effect for that interface.

140

Adding Port Filters

Select “Add TCP or UDP Filter”


Enter the following parameters

- IP Source address

- IP Destination address

- IP Protocol, TCP or UDP

- Source port or range of ports (associated with source IP address)

- Destination port or range of ports (associated with destination IP address)

- Direction, Inbound or Outbound

Select “Apply”

Save the new configuration

Restart the Mitel 1000

Adding Raw IP Filters

Filters based on IP address and protocol only can be added to the security level displayed.

Select “Add Raw Filter”



141

- IP Source address and Subnet Mask

- IP Destination address and Subnet Mask

- IP Protocol

- Direction, Inbound or Outbound

Select “Apply”



Host Validators

Traffic to or from specific hosts can be blocked by the firewall.

Select “Host Validators …” for a particular interface


Select “Add Host Validator … ” for the selected interface


Enter the host IP address and Subnet mask

Select the direction, “Inbound”, “Outbound” or “Both”

Select “Apply”


Restart the BROADBAND MODULE

142

Application Level Gateways

There are certain applications that NAT and Firewall configurations cannot manage. In many cases, ALGs (Application Level

Gateways) are needed to translate and transport packets correctly.

An ALG provides a service for a specific application such as FTP

(File Transfer Protocol). Incoming packets are checked against existing NAT rules or Firewall filters, IP addresses are evaluated and detailed packet analysis is performed. If necessary, the content of a packet is modified, and if a secondary port is required, the ALG will open one. The ALG for each application does not require any configuration.

ALG support is provided for the following applications. If support is required for additional applications, security triggers can be configured for these.

Application

AIM (AOL Instant Messenger)

FTP (File Transfer Protocol)

IKE (Internet Key Exchange)

ILS (Internet Locator Service)

MSN (Microsoft Networks)

PPTP (Point-to-Point Tunneling

Protocol)

RSVP (Resource Reservation

Protocol)

L2TP (Layer 2 Tunneling Protocol)

SIP (Session Initiation Protocol)

TCP Port

5190

21

N/A

UDP Port

N/A

N/A

500

389 (+1002)

1863

N/A

N/A

1723 N/A

N/A N/A

N/A

5060

1701

5060

Security Trigger

A security trigger can be defined for applications that are not supported by the ALGs listed above. A security trigger allows the firewall to dynamically open and close secondary ports associated with a particular application and to specify the maximum length of time the port remains open.

143

Select “Security Trigger Configuration …”

The following screen is displayed each entry.

Current security triggers are displayed. There is an option to delete

Select “New Trigger”



Transport Type

Port Number Start

Port Number End

Secondary Port Number

Start

Secondary Port Number

End

Adds a trigger for a TCP or UDP application

Sets the start of the trigger port range for the control session

Sets the end of the trigger port range for the control session

Sets the start port range that the trigger will open

Sets the end of the port range that the trigger will open

144

Allow Multiple Hosts

Max Activity Interval

Allow or Block sets whether or not a secondary session can be initiated to/from different remote hosts or the same remote host on an existing trigger

The max interval time in milliseconds between the use of the secondary port sessions. If a secondary port opened by a trigger has not been used for the specified time, it is closed

Enable Session Chaining If this is enabled, TCP dynamic sessions also become triggering sessions, which allows multi-level session triggering

UDP Session Chaining If this is enabled, UDP dynamic sessions also become triggering sessions, which allows multi-level session triggering

Binary Address

Replacement

Sets whether the destination IP address of the incoming packet is replaced with the associated internal IP address to allow NAT traversal

Address Translation Type Sets address replacement on a particular packet type.

Select “Apply”

Intrusion Detection

This is used to detect and block incoming attempts to attack or block traffic to the site.

Select “Configure Intrusion Detection … ”


145


Use Blacklist

Use Victim Protection

Victim Protection Block

Duration

DOS Attack Block

Duration

Scan Attack Block

Duration

Enables or disables blacklisting of an external host if the firewall has detected an intrusion from that host. Access is denied to that host for 10 minutes.

Enables or disables the blocking of incoming broadcast Ping commands for the period specified in Victim Protection Block duration.

The period for which incoming broadcast Pings are blocked.

The default setting is 600 seconds.

If a Denial of Service attack is detected, traffic from that host is blocked for the duration specified here. The default setting is 1800 seconds.

If scan activity from a host attempting to identify open ports is detected, traffic from that host is blocked for the duration specified here. The default setting is 86400 seconds (1 day).

Scan Detection

Threshold

If the number of scanning packets counted within the Scan

Detection Period exceeds the value set here, a port scan attack is detected. The default setting is 5 per second.

Scan Detection Period The duration that scanning type traffic is counted for. The default setting is 60 seconds.

Port Flood Detection

Threshold

This is the maximum number of SYN packets that can be received by a single port before a flood is detected. The default setting is 10 per second.

Host Flood Detection

Threshold

This is the maximum number of SYN packets that can be received from a host before a flood is detected. The default setting is 20 per second.

Flood Detection Period If the number of SYN floods counted within this duration exceeds either the Port Flood Detection Threshold or the

Host Flood Detection Threshold, traffic from the attacker is blocked for the DOS Attack Block Duration. The default setting is 10 seconds.

Maximum TCP Open

Handshaking Count

Maximum Ping Count

This is the maximum number (per second) of unfinished

TCP handshaking sessions that are allowed before a DOS attack is detected. The default setting is 5 per second.

This is the maximum number of Pings (per second) that are allowed before a DOS attack is detected.

Maximum ICMP Count This is the maximum number of ICMP ins (per second) that are allowed before a DOS attack is detected.

146

Select “Clear Blacklist” if you wish to clear all external hosts from the blacklist.

Select “Apply”

Save Configuration


Security Logging

Select “Configure Security Logging …”

The following page is displayed

Logging is enabled by default for Session Logging, Blocking

Logging and Intrusion Logging.

To disable all logging:

Select “Disable Security Logging”

Session Logging, Blocking Logging and Intrusion Logging.

To disable any of the above

Select “Disable”

One of eight logging levels for reporting can be selected from the drop down menu

Emergency

Alert

Critical

Error

Warning

Notice

Informational

Debug

The output can be directed to the Console or the Event Log.

147

Diagnostics

A range of tests is available which can help in diagnosing problems.

Select Diagnostics on the left-hand menu. The following screen is displayed: -

ADSL Test / ADSL Status

You can use the ADSL Test to identify any problems with your

Internet connection. The ADSL Test will run a set of tests on your

Internet connection and report back on anything preventing your connection from working.

The ADSL Test is only applicable when you are using the internal

ADSL Modem to connect Mitel 1000 to the Internet.

When should I run an ADSL Test?

Run an ADSL Test if you cannot access the Internet. If you are contacting your Internet Service Provider to report a connection problem, it may help to run an ADSL Test so you can give their support staff additional information.

Before running the ADSL Test it is advisable to check the status of the ADSL connection.

Select DSL status in the text ‘Before running an ADSL test, you may

want to monitor how your DSL connection is performing by looking at the DSL status page.’

The following page is displayed: -

148

Logging

If your system is having some problems, which are not, easily diagnosed you may be requested to enable logging. When enabled the system automatically sends detailed information to a server where specialist staff can analyze it. Select Logging on the left-hand side menu. The following screen is displayed: -

When requested to do so set Enabled to On. You may be requested to change the interval but in most cases this should be left at 240. When set at 240 the system automatically sends the information every four hours.

149

Status

You can examine the settings of the WAN, DMZ, LAN, VoIP,

Routing table and hardware and software.

Select Status on the left-hand side menu. The following screen is displayed: -

Note

If an IP Trunk is configured but not registered an X will be displayed after the Password. If the trunk is configured and registered a √ is displayed

150

Event Log

This primarily displays recent security events e.g. blocking incoming attempts to penetrate the firewall.

Ping

You can Ping to defined or user defined addresses

Remote Access

If requested to do so you can enable Remote access to allow maintenance personnel to access the system remotely.

Select Remote Access from the left-hand side menu. The following page is displayed: -

151

Your external IP address is shown. You provide this address to the maintenance engineer, as this is the address they use to access your system.

In order to make the access secure and prevent unwanted access you also define a Password that you supply to the maintenance engineer.

They will supply you with the IP address that they use to access your system. You enter this in the IP address field.

This ensures that access is allowed from that IP address only and is only allowed when the Password, which you define, is provided.

There is also a time out on the access that is set at 30 minutes. This can be increased or decreased as required.

Call Log

The system stores records of the last 250 calls made and received.

This log can be retrieved. The log is presented in a spreadsheet format.

Call Log in the Diagnostics drop down menu. The following menu is displayed: -

2. Select Download. You may be prompted to click on ‘here’ if the web browser blocks the download.

3. The records are presented in a spreadsheet format.

I/G or O/C : Incoming or Outgoing Call

152

Date : The Date the call was made

Start Time : The time the call started

Duration: The call duration

Line : The line the call was made on

Start phone : The phone that started the call

Finish phone : The phone that finished the call

Telephone number: The number dialed or received.

153

Firmware Update

WARNING

The Firmware Update page allows you to:

• Backup and Restore configuration files for your system.

• Download an updated software version and install it on your

Mitel 1000

It is recommended that the current programming of your system be saved, using Save and Restore, prior to uploading the new software. This allows you to restore the system configuration after you have uploaded the new system software

Note

About firmware versions

Firmware is a software program. It is stored as read-only memory on your Mitel 1000. Your product manufacturer s continually improving this firmware by adding new features to it and these features are saved in later versions of the firmware.

If there is a firmware update available you are strongly advised to install it on your Mitel 1000 to ensure that you take full advantage of any new feature developments.

Backup/Restore Configuration

This page allows you to backup the configuration settings to your computer, or restore configuration from your computer. You should backup the system configuration before you upload a new firmware version. This will ensure all programming including speed dial lists etc are saved and can be restored when the new version of software is uploaded.

To save the configuration to your PC select Backup. Allow a few minutes for the file to be downloaded from the system. Depending on the browser you are using you may be prompted to allow the file to be downloaded. If so the following screen will be displayed: -

154

Note

Select here. You will be prompted to save the file on your PC.

To restore the configuration select Browse in the restore configuration window.

Select the saved file and press Restore.

You will be prompted to Restart the Mitel 1000 once the file is uploaded.

Firmware update

Before proceeding to update the system firmware, you must have downloaded the required firmware file from the appropriate

Firmware update website.

1. From the left-hand menu, click on Firmware Update. The following page is displayed:

Browse>. Use the Browse file box to navigate to the relevant directory where the firmware version is saved.

155

4. Once you have selected the file to be installed, click Open. The file’s directory path is displayed in the Update file: text box.

6. The page tells you that the firmware update is currently being downloaded and installed on your Mitel 1000.

Once installation is complete, the following page is displayed:

7. You must restart your Mitel 1000 in order to make the Mitel

1000 aware that a new firmware version has been installed. To do this, click Restart.

Once the system has been restarted you should restore the database if you have saved it as shown above.

156

System Resets

This page allows you to reset your Mitel 1000 to its default factory settings.

The configuration settings of your Mitel 1000 are stored in a configuration file. When you set up your Mitel 1000 and access the web pages for the very first time, the configuration file contains a default factory configuration. This configuration has been set by your provider for you, and contains the basic settings that you can use without having to make extensive changes to the configuration.

If you do make changes to the default configuration but then wish to revert back to the original factory configuration, you can do so by resetting the Mitel 1000 to factory defaults.

You may need to reset to defaults if you have made changes to

Mitel 1000's settings causing it not to function properly.

If you are having problems connecting to your Internet Service

Provider, their support staff may request that you reset to defaults to help in the connection process.

Remember that all your previous settings will be replaced.

Resetting the system

1. From the left-hand menu, click on Reset Options The following page is displayed:

Note

Two options are presented, Reset and Reset to Defaults. Selecting

Reset invokes a reset but all the programming is retained.

Resetting to defaults deletes most of the system programming.

If you reset your Mitel 1000 to factory defaults, all previous configuration changes that you have made are overwritten by the factory default configuration.

157

This page reminds you that resetting to factory defaults cannot be undone – any changes that you have made to the basic settings will be replaced. If you are happy with this, click in the Confirm box to tick it, then click Reset to Defaults. The following page is displayed:

This page confirms that the Mitel 1000 is currently resetting to factory defaults. Once the reset is complete, Restart page is displayed.

Click Restart. The following page is displayed.

Resetting to defaults also resets the username and password to their default settings. When presented with the Log in page enter the default username, ‘admin’ and the default password ‘admin’.

158

A

Configuring Your Mitel 1000 via the

Featurephone

To enter system programming

If your extension is the Programming Extension you have access to the system programming options. If you select this option you will be prompted to enter the System Programming Password. If this option is selected from any other extension the display will show

‘Programming Refused’. Again, the default Programming Extension is extension 20.




Enter the System Programming Password to access system programming.

System Setup Options

Displaying caller numbers and routing calls

The Caller ID service is available on CO lines. If you subscribe to this service, your network sends the telephone number of callers to the Mitel 1000 (provided the caller has not elected to restrict the network from presenting their number). The telephone number (or associated name) is displayed on the ringing Featurephone.

The Caller ID information is also shown if the extension is equipped with a standard phone which supports the service.

Your telephone number will also be presented to persons you call, unless you restrict your number from being presented.

How a caller number is displayed at your extension

The caller’s number will appear on the display of all Featurephones programmed to ring for incoming calls.

If a name is associated with the number in either the system speed dial store or the Caller ID store the name will be displayed.

A caller may choose to withhold their identity. In this case, the display will show ‘Number Withheld’ instead of the caller’s number or name.

If the number information is not available the display will show

‘Number Unavailable’ instead of the caller’s number or name.

If more than one caller is calling at any one time, the number displayed will be that of the first call in the queue. When this call is answered by one of the ringing Featurephone the number of the next call in the queue will appear on the displays of the other ringing

Featurephones.

If your Featurephone is not ringing for the call you may examine the incoming call ID by selecting ‘Examine I/C Call’. The same information shown on the ringing Featurephone is then displayed.

159

To set up your system to display caller numbers received on CO lines (Caller ID service)

If you subscribe to the Caller Number display service from your

Network Provider then you can program the system to display the callers number.



Select ‘System programming’.

Enter the System Programming Password and select ‘Lines’.

Press the Scroll Down Key (Ô) until ‘PSTN Programming’ is displayed.

Press the Scroll Down Key (Ô) until ‘Caller ID Detection’ is displayed.

Select ‘Caller ID detection’.

Select the lines that have the Caller ID service enabled. The lines you select will have a ♦ displayed beside them.


To associate a caller number with a name, and route its calls to an extension

Up to a hundred names, each a maximum of ten characters,

(including spaces), may be associated with caller telephone numbers. When a number with an associated name is received, the name rather than the number is displayed.

Furthermore an extension number may also be associated with a telephone number. In this case an incoming call from that number will ring at only that extension..


Press the Scroll Down Key (Ô) until ‘System Programming’ is displayed.

Select ‘System Programming’.


Press the Scroll Down Key (Ô) until ‘CID Programming ’ is displayed.

Select ‘CID Programming .’.

Select an Index Number (01 - 30).

Enter the caller telephone number.


Enter the name to be associated with the number. Refer to page 35 for help on how to enter names.

Select the destination you wish to route calls from that number to.

Caller ID Lists – storing all calls or unanswered calls only

The system Caller ID lists can store either all calls or unanswered calls only.




160

Enter the System Programming Password and select ‘System’.

Press the Scroll Down Key (Ô) until ‘Caller ID List’ is displayed.

Select ‘Caller ID List’.

Select ‘Store All Calls’ or ‘Store Unanswered Calls’.


To set up extensions with an individual Caller ID List

You can program up to twelve extensions to store five numbers each. Each of these extensions will have a separate record of calls that ring on exchange lines programmed to ring their extensions only.




Enter the System Programming Password and select ‘Extensions’.

Press the Scroll Down Key (Ô) until ‘Personal Caller ID List’ is displayed.

Select ‘Personal Caller ID List’.

Select the extensions that you wish to have an individual Caller ID list. The extensions with a Personal Caller ID list have a ♦ displayed beside them.


Automatic line selection

This facility allows users to make external calls without having to enter the line access codes (9,8). Internal calls are made by pressing hookflash and dialing the number when using standard or cordless phones or selecting the number from the internal call menu on a Featurephone.



Enter the System Programming Password and select ‘System’

Select Automatic Line selection and select ‘Automatic Line selection

On’.

Paging

To protect Featurephone against Announcements and Voice Calls

By default, all Featurephone may be paged. You can page-protect each Featurephone to prevent it from being paged from either

Announcements or Voice Calls.





Select ‘Page protection’

Select the extensions you wish to protect. A

♦ is displayed beside protected extensions.


161

Least Cost Routing

To set up codes to allow calls to be routed on specific lines or networks





Scroll Down and select ‘LCR Codes' .

Select LCR On to activate the facility

Enter in a code index (01-50).

Enter an input code (Up to 5 digits). Press Confirm. This is the code dialed by the user.

Enter an Output Code (Up to 9 digits). This is the code that will be inserted before the telephone number that the user dials. This code can be used to select a specific Network Provider.

Select the preferred or exclusive option.

If ‘Exclusive’ is selected the calls can only be sent on the lines selected below.

If ‘Preferred’ is selected the calls will be routed on any available line, if none of the selected lines are available. In this case the output code is not dialed.

When Enabling or Disabling the LCR feature the new setting does not take immediate affect. There can be a delay a of up to 1 minute for the setting to take affect.

Least cost Routing activated automatically at set times

You can program the Least Cost Routing facility, to be automatically turned on and off twice during a 24-hour period enabling you to tailor your call charges through different service providers.





Scroll Down until ‘LCR Timebands' is displayed.

Select LCR on times

You can enter two 'On' times.

Select LCR off Times

You can enter two times at which the LCR facility is deactivated

A Third option 'LCR weekend' is offered. When this is selected the

LCR service remains active from Friday night to Monday morning, all off times over the weekend are ignored.


To examine Extension Lock Passwords




162


Select ‘Examine passwords’

Select ‘Ext. lock password’.

Select the extension. The Lock Password is briefly displayed on the top line of the display.


Call Waiting Tone Protection

Extensions may present a busy extension with a Call Waiting tone, provided the busy extension is not protected against receiving Call

Waiting tones. By default, all extensions are protected against receiving Call Waiting tones. However, you may program extensions to receive Call Waiting tones.

To program an extension to receive Call Waiting tones

From the Programming Extension, select the PROGRAM Key




Press the Scroll Down Key (Ô) until ‘Tone protection’ is displayed.

Select the extensions you wish to allow receive Call Waiting tones.

A ◊ is displayed beside those extensions allowed to receive Call

Waiting tones, and a

♦ is displayed beside those extensions protected against receiving Call Waiting tones. (By default, all extensions will have a

♦ displayed).


To protect an individual call from Call Waiting tones

If your extension can receive Call Waiting tones, you may protect each call on an individual basis from interruption.

When you are on a call, select ‘Tone protect’ on the display.


Barge-In

To Program extensions allowed to barge-in

In default no extensions are programmed to activate “Barge-In”.

From the Programming extension, press the PROGRAM key.

Press the Scroll Down key (Ô) until “System Programming” is displayed.

Select “System Programming”.

Enter the System Programming Password and select “Extensions”.

Press the Scroll Down key (Ô) until “Barge-In” is displayed.

Select “Barge-In Extensions”.

Select the extensions that are to be allowed to barge-in. The extensions you select will have a “

♦” displayed beside them.

The default is that no extensions are allowed to barge-in.

To Program extensions protected from “Barge-In”



163




Select “Barge-In Protection”.

Select the extensions that are to be protected from barge-in. The extensions you select will have a “

♦” displayed beside them.

The default is that no extensions are protected.

To Program “Barge-In” with or without tone






Select “Barge-In Tone”.

Select Barge-In tone on or off. The selection is indicated with a “

♦”.

In default tone is provided when barge in is activated. This is a single burst, which lasts for about a half a second.

Incoming Call Handling

This option is used to allocate extensions to answer incoming calls on the lines.

Associating lines with extensions for Incoming Ringing

By associating lines with extensions you can have lines ringing different extensions in Day and Night modes.




Enter the System Programming Password and select 'Lines'

Select ‘Incoming Ringing’.

Select the line or IP Trunk.

Select ‘Day’ or Night’.

The extension menu is presented. Select the extensions that are to ring for calls on the line. A solid diamond,

♦, indicates these extensions.


This feature allows you to have calls ringing with a different ringing signal routed to different extensions than calls ringing with the normal ringing signal. The facility of having a second number on a

CO Line, which rings with a different signal, must be provided by the

Network Operator. The recommended use for this facility is to have a separate number for Fax calls and route these calls to an extension equipped with a fax machine.



Enter the System Programming Password and select 'Lines'

Select ‘Distinctive Ringing’.

164

Select the Line

Select Day or Night Mode

Select those extensions that are not to ring. In default all extensions are programmed to ring. A solid diamond,

♦, indicates the extensions that will ring.

Restricting Outgoing Calls

This feature lets you decide which lines each extension can access for outgoing calls. By default, all extensions have access to all lines.

To restrict an extension from accessing a particular CO line





Press the Scroll Down Key (Ô) until ‘Outgoing restriction’ is displayed.

Select ‘Outgoing restriction’.

Select the line.

Select the extensions to be prevented from accessing that line. A

♦ is displayed alongside those extensions that are restricted from accessing the line, and a ◊ is displayed alongside those extensions that have access to the line.


.

Outgoing Groups

To program lines into groups for access using the codes 9 or 8.

‘Exchange Lines and IP Trunks’ can be grouped together in two

Outgoing Groups. Each Outgoing Group is associated with a code.

These codes are 9 or 8, with Group 1 being associated with 9, etc.

Dialing a code selects a line from the associated Outgoing Group.





Press the Scroll Down Key (Ô) until ‘Outgoing groups’ is displayed.

Select ‘Outgoing groups’.

Select the Group you wish to set up. Two Groups can be set up, each with a corresponding access code – 9 or 8.

Select the lines to be in the Group. The lines in the Group are indicated by a

♦.


Lines can be in one Outgoing Group only. Selecting a line to be a member of a Group automatically removes it from all other Groups.

165

Local Codes

The Caller ID number presented from the network is the 10 digit national number. It does not include the 1 that is required for toll calls. The system must be able to distinguish between local and toll numbers so that they can be correctly dialed from the Caller ID stores.

This is achieved by entering the local codes in the Local Codes table.

When a number is received, the local area code is compared to the codes entered in the Local Codes table. If the digits do not match, the digit 1 is added as the toll access digit and the number, including the leading 1, is stored in the Caller ID store.

If there are two or more local codes programmed in the Local

Codes table then the 10 digit local number is stored and dialed for local calls.

If there is only one local code programmed in the Local Codes table then the area code is stripped and the 7 digit local number is stored and dialed.





Scroll down to Local Codes

Select the index 01-40

Enter the code.

Enter all Local codes.

Day/Night Service

The ‘Day Service’ / ‘Night Service’ feature allows you to change the extensions which ring on incoming calls, change the Class of

Service at each extension, and change the voice greeting heard by callers (if you have voicemail installed). These changes can take place automatically, at pre-programmed times daily, or can be invoked manually. Furthermore, the system can be programmed to remain in ‘Night Service’ over the weekend.

To set the automatic start and end times for Night Service

The Automatic ‘Night Service’ feature allows you to set two time bands in each twenty-four hour intervals; the system then automatically enters ‘Night Service’.





Press the Scroll Down Key (Ô) until ‘Night Service’ is displayed.

Select ‘Night Service’.

Select ‘Automatic on times'

Select 'On Time 1' to set the first time the ‘Night Service’ turns on automatically

166

Select 'On time 2' to set the second time the ‘Night Service’ turns on automatically.

Select the Automatic Off times and set the two times that ‘Night

Service’ is to turn off

To manually turn on Night Service

The Manual ‘Night Service’ feature enables you to turn ‘Night

Service’ on or off manually. When you turn '‘Night Service’' on, the

'‘Night Service’' ringing and 'Class of Service' come into operation.

At extension 20, select ‘‘Night Service’’.

To have Night Service remain on over weekends

The Weekend Service feature ensures that if ‘Night Service’ is invoked on a Friday evening, the switch remains in ‘Night Service’ until Monday morning.





Press the Scroll Down Key (Ô) until ‘Night Service’ is displayed.

Select ‘Night Service’.

Select ‘Weekend service’. A

♦ symbol indicates the service is on and a

◊ symbol indicates it is turned off.

Press the Speakerphone Key to finish programming

To cancel Weekend service, repeat as above, selecting ‘Weekend service off’ as the last step.

System Time/Date

To set the time and date on the system


Press the Scroll Down Key (Ô) until ‘System programming’ is displayed



Select ‘Time and date’.

Enter the correct time in 24-hour format, (e.g. 2pm as 1400). The display will prompt for a date.

If you only wish to set the time select ‘Confirm’ and the display will revert to the Idle Menu.

Enter the date in mm/dd/yy format, (e.g. 10 December 1999 as

121099). When the date has been entered the display will revert to the Idle Menu.


In the event of a power failure, you will need to reset the time and date.

Changes to the system Time will only take place when any external calls in progress at that time have cleared.

If Caller ID is supplied on a CO line the system time will be updated by the first incoming external call after 0200 hours.

167

Note

Note

Hold Options

When an external call is placed on hold, you can choose between supplying music, a tone, or silence to the caller. The music source can be internal, in which case it is integrated into the system and cannot be changed, or external, in which case an external source must be connected to your system.

To supply music, tone or silence to callers on hold





Press the Scroll Down Key (Ô) until ‘Music on Hold’ is displayed.

Select ‘Music on hold’.

Select the option (‘Internal Source’, ‘External Source’, ‘Tone on

Hold’ or ‘Silence’) that you want. The default is ‘Internal Source’ and the

♦ indicates the current program setting. Internal callers are always returned ‘Tone on Hold’.


Hotline


To have an extension dial a number automatically, when the handset is lifted





Press the Scroll Down Key (Ô) until ‘Hot line’ is displayed.

Select ‘Hot line’.

Select the extension from the Extension Menu.

Enter the number to be dialed. If you wish to dial an external number, enter 9, or another line access code, before the external telephone number, to select a line.


When a Featurephone is programmed as a Hot Line, no other facilities can be invoked after it is programmed. As soon as you go off-hook on the Featurephone, the number is dialed..

A common application for the Hot Line feature is for a fax or modem. The extension can be set to automatically select a CO line so the fax or modem does not have to dial 8.

168

Assigning Extension Names

You may assign names to extensions. When an extension receives an internal call, its display will show the calling extension name in the place of the calling extension number.

To assign a name to an extension





Select ‘Name programming’.

From the Extension Menu, select the extension you want to name and enter the name as described on page 35. Up to ten characters

(including spaces) can be entered for each name.

When the name is entered, select ‘Confirm’. You will be presented with the Extension Menu and can continue programming other names.



Each extension may be programmed for a Class of Service. This determines the type of call the extension is allowed to dial. Four tables, which can be programmed with up to fifty codes, are used to implement six Classes of Service:

By default, all extensions are in Class 1, that is, they have no restriction placed on them.

An extension placed in Class 2 is restricted from dialing the codes programmed in Table 2. (Table 2 would typically be programmed with the international access code 00).

An extension placed in Class 3 is restricted from dialing the codes programmed in Tables 2 and 3. (Table 3 would typically be programmed with non-local national access codes).

An extension placed in Class 4 is restricted to internal and emergency, calls only.

An extension can be placed in Class 5 in addition to being in Class

2 or 3. In this case the codes programmed in Table 5 are allowed.

An extension can be placed in Class 6 in addition to being in Class

1, 2 or 3. In this case the codes programmed in Table 6 are restricted.

The following table shows the types of restriction for the different

Classes of Service available:

Type of restriction Table Class

No restriction

Restrict codes in Table 2

Restrict codes in Table 2 and 3

Internal and emergency calls only

Allowed codes that can be combined with Class 2 or 3

Restricted codes that can be combined Class 1, 2 or 3

-

Table 2

Table 3

-

Table 5

Table 6

3

4

5

6

1

2

169

The emergency codes are ( 911, 060, 066, 080, 100, 101, 105, 106,

107, 110, 112, 115, 116, 118, 119, 123, 127, 128, 131, 132, 133,

156, 171, 190, 191, 192, 193, 194, 197, 198, 199, 211, 311, 511,

912, 913, 990, 999). They cannot be barred.

Both Classes 5 and 6 can be associated with the same extension.

Class 5 cannot be associated with Class 4 extensions.

To set up Class of Service access tables





Press the Scroll Down Key (Ô) until ‘Class codes’ is displayed.

Select ‘Class codes’.

Select the ‘Table’ to which you want to assign codes. (Table 2, 3,

Allowed Table, or Restricted Table).

Select an ‘Index number’ and enter the code.

When entering a code an additional option is given on the display of your Featurephone. This option is the “Any” key, which when selected inserts the symbol “X” into the next character of the code

(number) you are entering. The symbol “X” will represent any number (1 to 0).

Select ‘Confirm’ when the code is entered.


To restrict extensions during the day

With this feature, you can assign the extensions to a Class of

Service that will operate when the system is in ‘Day Service’. On power-up, all extensions are in Class 1.





Select ‘Restriction classes’.

Select ‘Day Class of Service’.

Select the Class you want to assign to the extensions, (Class 1 –

Class 6).

Select the extensions to be entered in this Class.


To restrict extension during the night

With this feature, you can assign the extensions to a Class of

Service that will operate when the system is in ‘Night Service’. On power-up all extensions are in Class 1.





170

Note

Select ‘Restriction classes’.

Select ‘Night Class of Service’.

Select the Class you want to assign to the extensions, (Class 1 –

Class 6).

Enter the extensions to be entered in this Class.


To allow extensions use System Speed Dials overriding call restrictions

You may wish to allow extensions to dial numbers entered in the

System Speed Dial list, which they are restricted from dialing directly. For example, these could be numbers that extensions in

Classes 2, 3 or 4 cannot dial directly. Entering these numbers into the System Speed Dial list and activating this feature on the extensions allows the restricted extensions to access these numbers.

By default, this feature is not activated on any extension.





Press the Scroll Down Key (Ô) until ‘Sys. Speed no. override’ is displayed.

Select ‘Sys. speed no. override’

Select the extensions on which you wish to activate the feature.

Those extensions allowed to dial System Speed Dial numbers not normally appropriate to their Class of Service are indicated by a

♦.


Numbers in an extension’s Personal Speed Dial list cannot override the Class of Service restriction of the extension

Using Voicemail

Voicemail

Voicemail common parameters

Up to 8 extensions can be allocated voice boxes.

The maximum number of messages that can be stored in a Mailbox is 20 at power up. This number is programmable from 10 to 50 messages.

The maximum message and Greeting length is programmable between 60-180 seconds. The time allocated at Power Up is 120 seconds.

Unretrieved messages are deleted in 15 days and retrieved messages are deleted in 3 days.

An extension must be allocated a Voice Mailbox before it can use voicemail. In default, extensions are not allocated a Voice Mailbox.

To allocate a Voice Mailbox to an extension

From the Programming extension, press the PROGRAM Key

171




Press the Scroll Down Key (Ô) until ‘Voice Mail Boxes’ is displayed.

Select ‘Voice Mail Boxes’

Enter the extensions to be allocated a Voice Mailbox. Those allocated a box will be indicated by a

♦.


Remote Notification

Selecting the Extensions that can activate remote notification

In default no extension can set remote notification. Those extensions that can set remote notification are programmed in system programming.






Select the extensions that are to be allowed to use remote notification .

Selecting the Number of Simultaneous Calls

The number of simultaneous remote notification calls can be set at

1 or 2.




Enter the System Programming Password and select “System”.


Select “Simultaneous Calls”.

Enter the value 1 or 2 and press “Confirm”.

The default value is set at 1.

Selecting the Number of Retry Attempts

The number of simultaneous remote notification calls can be set at

1 or 2.






Select “Retry attempts”.

Enter the value from 2 to 15 and press “Confirm”.

The default value is set at 2.

Selecting the Line Group that the Remote Notification calls are to use

The outgoing line group to be used for remote notification calls can be changed.

172






Select “Outgoing group”.

Select the group.

Notification delay timer

The time interval between receiving a message and making the first remote notification attempt is programmable. This is set at 15 minutes (900 seconds) in default and can be set between 1 and 30 minutes (60 - 1800 seconds).





Select “Timers”.

Select “Notification Delay”.

Enter the value between 60 and 1800 seconds and press “Confirm”.

Notification interval timer

If a remote notification fails this is the time the system waits before retrying the call. This is set at 5 minutes (900 seconds) in default.

The range is 1-15 minutes (60 - 900 seconds).





Select “Timers”.

Select “Notification Interval”.

Enter the value between 60 and 900 seconds and press “Confirm”.

Call Recording

Those extensions allowed to record calls are set via system programming.




Enter the System Programming Password and select ‘Extension’.

Scroll down and select ‘Call Recording’.

Select those extensions that are to be allowed record calls.

Voicemail Capacity

You change the message capacity of Mailboxes from the default of

20 messages per Mailbox to a higher or lower amount from 10 to 50 depending on demand.





173

Press the Scroll Down Key (Ô) until ‘Mail box capacity’ is displayed.

Select ‘VM capacity’

Enter the maximum number of messages to be stored per Mailbox.


Voice Mail capacity % used

This feature tells the Administrator when the Voice Module capacity is approaching it's limit. When the voice module storage reached

88% of it's total capacity the system will display on the top line of extension 20 the message 'ALARM MAIL ALMOST FULL'. This text will remain on the display until the capacity falls below the 88% mark again. This allows the administrator to remind user to delete old or unwanted voice mails to free up some storage time.

The Administrator can also view the % capacity used by individual voice boxes or the system box. To view this

Enter system programming and select "Extensions".

Scroll through the menu and select the "VM Capacity % Used" option.

Select the "System VM box" to view the % used by the system box.

To view the % used by an extension voice box select "Extensions".

A list of extensions is shown with a solid diamond indicating an extension with a voice box enabled.

Select the required extension to view, the top line of the display will show the % of the extension's voice box that is used.

To turn on your Voice Mailbox

When an extension is allocated a Mailbox ‘Forward’ on no answer is automatically set to the Voice Box. All calls not answered by the extension are automatically answered by the Mailbox.

If you wish to have all calls go immediately to the Voice Mailbox you can activate ‘Forward All Calls’ to the Voicemail. You turn on your

Voice Mailbox by Forwarding calls to the number 710.

Select ‘Forward’ on the idle menu and choose ‘Forward all calls’.

Select ‘Forward to VM’ or enter 710 as the extension number

If ‘Forward on no answer’ is activated to 710, calls unanswered after four rings will be answered by the Voice Mailbox.

If ‘Forward when busy’ is activated to 710 calls you cannot receive will be answered by the Voice Mailbox.

To check all Voicemail Passwords

All extension Voicemail Passwords can be examined from the

Programming Extension.





Select ‘Examine passwords’.

Select ‘Voicemail password’.

Select the extension whose password you wish to examine. The

Voicemail Password of that extension is briefly displayed on the top line of the display.

174

WARNING



This feature allows you to set up an Answering Machine to answer incoming calls. You can select which lines are to be answered by the Answering Machine when it is turned on. It can be used on both

CO lines and IP Trunks. You can select how long a call rings before the Answering Machine answers.

All messages received are stored in a system Answering machine, which is controlled by extension 20. Extension 20 can also customize the greeting. You can turn the Answering Machine service on and off at any time at extension 20 and its operation is independent of ’Night Service’.

You can use this service if you are not answering calls at lunch or at night, or simply want to record messages from callers. If desired, you can have this feature on permanently, so that calls, which are not answered for a programmable period, are answered by the

Answering Machine.

If a call is received when the Voice Module storage is full, it will not be possible to store any further messages. To manage the voice mail and free up storage space see the section "Using

Voicemail and other Voice Services" on page 62.

To turn the Answering Machine on and off

At extension 20, press the Scroll Down Key (Ô) until Answering

Machine’ is displayed.

Select ‘Answering Machine’’

The top line of the display will display the ‘Answering Machine’ prompt. To turn the answering machine off press ’Answering

Machine’ again.

To program lines to be answered by the Answering machine


Press the Scroll Down Key (Ôv) until ‘System programming’ is displayed.



Press the Scroll Down Key (Ô) until ‘Answering Machine’ is displayed.

Select ‘Answering Machine’

Select the lines to be answered by the Answering machine. The lines that will be answered are indicated by a

♦.


To set the time a call will ring before the Answering Machine answers





175

Press the Scroll Down Key (Ô) until ‘Timers’ is displayed.

Select ‘Timers’.

Select ‘Answering Machine Delay ’

Enter the time. The default is 010 seconds.


Programming Additional System Options

Doorphone

To set up a Doorphone on your System





Select ‘Doorphone'.

Select ‘Doorphone equipped’.


To program which extensions can operate the Doorstrike





Press the Scroll Down Key (Ô) until ‘Open door restriction’ is displayed.

Select ‘Open door restriction’.

Select which extensions are restricted from opening the door. The extensions restricted from operating the Doorstrike will be indicated with a

♦.


External Forwarding Options

This allows you to decide if External callers or External and internal

Callers to your extension are Forwarded externally if you have set an external Forward. It also allows extensions to be prohibited from activating an external forwarding.





Press the Scroll Down Key (Ô) until ‘External Forwarding' is displayed.

Select 'External forwarding'.

Select ‘No trunk to trunk calls’.

176

Note

Select the extensions that are not allowed to activate an external forwarding or set up trunk to trunk calls.

If both internal and external calls are to be Forwarded select 'All calls'.

If external calls only are to be Forwarded select 'External calls only'

Miscellaneous system configuration options

To change the system Language

The text prompts can be presented in English, French or Spanish.





Select ‘Language’.

Choose English, French or Spanish.

Each extension can choose their own language if they wish it to be different from the language selected here.

To change the Programming Extension

System programming can only be carried out at one Featurephone, that is, the Featurephone connected to the Programming Extension.

By default, extension 20 is the Programming Extension. The

Programming Extension can be changed to any other extension if required.





Select ‘Programming position’.

Select the extension you wish to have as the Programming

Extension. The selected Programming Extension is denoted by a

♦.


To change the System Programming Password

The default System Programming Password (1111) can be changed to any 4-digit number.





Select ‘Change password’.

Select ‘Change’ and enter the 4-digit number you require.

Select ‘Confirm’.


177

Note

To configure unequipped line interfaces

The system assumes that available line interfaces have exchange lines connected to them. If a line interface does not have an exchange line connected ensure correct system operation by unequipping the line interface in system programming, as follows:





Press the Scroll Down Key (Ô) until ‘Equipped Lines’ is displayed.

Select ‘Equipped lines’.

Select the lines you wish to equip or unequip. Equipped lines are denoted by a

♦. Unequipped lines are denoted by a ◊.


To configure disconnected extensions

The system assumes that all available extension interfaces have

Mitel 1000s connected to them. If an extension interface does not have a Mitel 1000 connected, ensure correct system operation by disconnecting the extension interface in system programming, as follows





Press the Scroll Down Key (Ô) until ‘Extension disconnect’ is displayed.

Select ‘Extension disconnect’.

Select the extensions you wish to connect or disconnect.

Disconnected extensions are denoted by a

♦.


When a Featurephone is connected to an extension interface that is programmed as disconnected, the Featurephone display may appear as if the Featurephone is connected. However, when the handset is lifted a busy tone is heard and no options will be displayed.

To examine system passwords





Press the Scroll Down Key (Ô) until ‘Examine passwords’ is displayed.

Select ‘Examine passwords’.

Select either ‘Extension lock password’, or ‘Voicemail password’, or

‘System VM box’.

178

1. If you selected ‘Extension lock password’, the extension menu will appear. Select an extension and its Extension Lock

Password will appear on the display.

2. If you selected ‘Voicemail password’, the extension menu will appear. Select an extension and its Voicemail Password will appear on the display.

3. If you selected ‘Answering machine’, the Answering machine

Password appears on the display.


To configure Line Key Lights

When a call is placed on System Hold, you can decide if the associated Line Key Light is to flash or remain steady on all other

Featurephone. The default setting is that the light flashes.





Press the Scroll Down Key (Ô) until ‘Line key light’ is displayed.

Select ‘Line key light’

Choose either ‘Light flashing on hold’ or ‘Light steady on hold’.


To prohibit trunk-to-trunk calls on an extension

You may prohibit individual extensions from activating External

Forward, External Transfer and External Conference. (These features set up so-called trunk-to-trunk calls).





Press the Scroll Down Key (Ô) until ‘External Forwarding’ is displayed and select.

Select ‘No trunk-to-trunk calls’.

Select the extensions to be denied this feature. Those extensions denied the feature are indicated by a

♦.


To Change ringing from 20 to 50 Hz

This option allows the ringing frequency to be changed from the default 20Hz to 50 Hz on individual extensions.



Enter the System Programming Password and select 'Extensions'.

Press the Scroll Down Key (Ô) until ‘20/50 Hz ringing' is displayed.

Select '20/50 Hz ringing'.

Select the extensions to ring at 50 Hz

The default is that all extensions are set for 25 Hz ringing.

179

Inverting ringing cadences

The external and Internal ringing cadences can be interchanged on an extension by extension basis.




Press the Scroll Down Key (Ô) until ‘Reverse Cadence ' is displayed.

Select 'Reverse Cadence'.

Select the extensions that require the cadences changed

Keypad Feedback

When off hook on an extension fitted with a Featurephone, a confirmation tone is played when a digit is pressed. This is so that the user knows that a digit was dialed.




Press the Scroll Down Key (Ô) until ‘Keypad Feedback' is displayed.

Select 'Keypad Feedback'.

Select the extensions that require the confirmation tone to be played.

To configure CO lines

There are various options to configure the CO line interfaces on your system. It is recommended that these settings should only be altered from the original settings if there has been a change in the network connection.





Press the Scroll Down Key (Ô) until ‘CO Programming’ is displayed.

Select ‘CO' programming’.

Select the desired option as detailed in the table below. The options are either explained in the following pages or in the referenced pages


CO Programming Option Default setting Alternate setting

Caller ID Detection

Dialtone detection

Long CO Line

Caller ID not set

Off

Off

Caller ID set

On

On

180

Programming Caller ID Detection

On standard CO lines on the Mitel 1000 the 'Caller ID Detection' option is programmed. The system can then detect when Caller ID information is being sent from the network and display the number.





Press the Scroll Down Key (Ô) until ‘PSTN programming’ is displayed.

Select ‘PSTN programming’.

Press the Scroll Down Key (Ô) until 'Caller ID Detection' is displayed.

Select 'Caller ID Detection' The lines with 'Caller ID Detection' programmed are indicated with a

♦.

Programming Dialtone Detection

This feature is provided as a programmable option under CO programming and is enabled to prevent the system from dropping the line when dial tone has not been detected. When enabled dial tone is not detected and the line is released if no digit is dialed until the expiration of the "Dialing time-out timer"







Press the Scroll Down Key (Ô) until ' Dialtone detection' is displayed.

Select ' Dialtone detect' The lines with ' Dialtone detection' enabled are indicated with a

♦.

Long CO Line

In some situations if the transmission on the CO Line is poor it may be necessary to change this setting which changes the impedance presented to the line.







Press the Scroll Down Key (Ô) until ' Long CO Line’ is displayed.

Select ' Long CO Line’. The lines with ' Long CO Line’ enabled are indicated with a

♦.

181

Button Hopping

When Button hopping is enabled if you press a second line key while on a call on another line the first call is disconnected. With button hopping off the first call is placed on hold when the second line key is pressed.





Press the Scroll Down Key (Ô) until ‘Button Hopping’ is displayed.

Select Button hopping On or Off as required.

To set system timers

You can set various timers from the Programming Extension to suit your requirements.





Press the Scroll Down Key (Ô) until ‘Timers’ is displayed.

Select ‘Timers’

Select the required timer to be changed and enter the duration.

(See table below).

Confirm the new time.


Recall on hold

Recall on transfer

Forward on no answer

Open the door

Doorphone ring duration

Call park

Ringback time duration

Answer machine delay

Programmable message length

Notification delay

Notification interval

001 – 1800

001 – 180

01 – 30

01 – 30

01 – 30

001 – 600

01 – 30

01 – 30

30 - 180

60-1800

60-900

90 seconds

90 seconds

11 seconds

5 seconds

30 seconds

180 seconds

30 seconds

10 seconds

120 seconds

900 seconds

300 seconds

Recall on Hold

This is the time that elapses before a call, which has been placed on hold, rings back the extension that put the call on hold.

Recall on transfer

This is the time that elapses before a call, which has been transferred and not answered, rings back the extension that attempted the transfer.

182

Forward on no answer

This is the time that elapses before a call ringing at an extension, with ’Forward On No Answer’ set, is Forwarded.

Open the door

This is the time that the Doorstrike relay will remain open following activation.

Doorphone ring duration

This is the time that extensions will ring when the Doorphone is pressed.

Call Park

This is the time that elapses before a call placed on ‘Call Park’ rings back the parked call extension

Ringback time duration

This is the time an extension will ring when Ringback has been invoked.

Ans. Machine delay

This is the time that elapses before an unanswered incoming call is presented with the Answering Machine greeting.

Programmable message length

This is the maximum length of a message left in a Mailbox or a

Greeting for a Mailbox.

Notification delay

This is the delay between receiving a voice mail message and attempting a remote notification call.

Notification Interval

This is the delay after making an unsuccessful remote notification call before attempting another call.

To reset your system

WARNING

There are two system reset options available – a warm and a cold reset.





Press the Scroll Down Key (Ô) until ‘Reset options’ is displayed.

Select ‘Reset!’ or ‘Reset to default!’

These are complete system resets, not individual extension resets. Selecting ‘Reset!’ (warm reset) will reset the system and cut off all established calls. Selecting ‘Reset to default!’ (cold reset) will reset the system, cut off all established calls and remove all programming from the system.

183

B

Cordless Phone Detailed Instructions

Battery requirements: The handset requires power source of two rechargeable NiMH batteries, size AAA 1.2V 750mAh (HR10/44).

WARNING

Safety precautions:

• Do not allow the handset to come into contact with liquids or moisture.

• Do not allow the charging contacts or the battery to come into contact with conductive materials.

• There is a slight chance that the telephone could be damaged by an electrical storm. It is recommended that users unplug the phone from the mains supply and telephone socket during a storm.

• Do not use the handset in an explosive hazard area such as where there is gas leaking.

• Because the phone works by sending radio signals between the base unit and the handset, wearers of hearing aids may experience interference in the form of a humming noise.

• We advise that this phone should not be used near intensive care medical equipment or by persons with pacemakers.

• Your phone can interfere with electrical equipment such as answering machines, TV and radio sets, clock radios and computers if placed too close. It is recommended that you position the Mitel 1000 at least one meter from such appliance

Use only the mains adapter supplied with this telephone.

Incorrect adapter polarity or voltage can seriously damage the telephone. Input: 110 VAC 50 Hz Output: 9 VDC 300 mA

WARNING

THERE IS A RISK OF EXPLOSION IF THE BATTERY IS

REPLACED BY AN INCORRECT TYPE. Never use nonrechargeable batteries. Use two rechargeable NiMH batteries, size AAA 1.2V 750mAh (HR10/44) only. NiMH batteries must be disposed of in accordance with the applicable waste disposal regulations.

Setting up your phone

1. Connect the output plug of the mains adapter to the socket on the back of the charger unit and the mains adapter to the wall mains supply.

2. Place the 2 rechargeable NiMH AAA batteries (included), observing their polarities, into the battery compartment on the handset. Slide the battery door firmly into place.

3. Place the handset on the base unit and let the batteries charge for a full 14 hours before using it for the first time.

184

Note

The handset may get warm during the initial charge.

Switch on/off your phone

To switch off the power of your phone press and hold during standby.

To switch on the power of your phone press . The battery icon will display in 10 seconds. If the battery level is too low, the handset may not power up.

To set your handset’s clock

Your clock resets to 12:00AM or 00:00, depending on time format you are using, each time you replace the batteries or switch off the phone.

To set your clock:

Press MENU during standby.

Press to select DISPLAY, and then press OK.

Press to select CLOCK, and then press OK.

Press to change the HOUR, and then press

Press to change the MINUTE.

If you set the time format of your clock to 12 hours, go to step 6. If you set it to 24 hours, go to step 7.

Press. Press to select AM/PM.

Press OK to confirm.

SET THE CLOCK TO 12 HOURS/24 HOURS

To change your phone’s time format:

1. Press MENU.

2. Press to select DISPLAY. Press OK.

3. Press to select TIME FORMAT. Press OK.

4. Press to select 12 HOURS or 24 HOURS.

5. Press OK to confirm.

Using your phonebook

You can use your phonebook to manage your contacts. Your phone has a private phonebook and a shared phonebook. The information in your private phonebook is stored in your handset. If you have more than one handset, each handset has its own phonebook.

The information in your shared phonebook is stored in System

Speed dial list in the Mitel 1000. The information is shared by all the handsets cordless and wired. See system speed dial on page 42 on the programming of the list from a Featurephone.

Your phone must have a link with the base unit in order to use the shared phonebook.

Your private phonebook can store 100 records and the system phonebook also has 99 records.

185

Note

To store a name and number in the private phonebook

Press NAMES.

Select the private phonebook and press OK.

Select ADD ENTRY, and then press OK.


Enter the number. In the Private phone book the line access code 9 or 8 must be entered.

Press SAVE to confirm the information you have entered.

To store a name and number in the shared phonebook

Press NAMES.

Select the shared phonebook and press OK.

Press to select ADD ENTRY, and then press OK.


Enter the number. In the Shared phone book enter the external number only. The line Access code must NOT be entered.

Press SAVE to confirm the information you have entered.

The shared phonebook is the system speed dial list. Numbers can be entered from a Featurephone or the web management interface as well as the Digital Cordless phones

Managing your contacts

1.Press NAMES and select PRIVATE. Press OK.

3. Press OK to select VIEW

4. Scroll to the contacts you wish to view or search by letter.

To view the details of your contacts press OPTIONS.

Select DETAILS. Press OK. The details of the contact you selected are displayed.

Programming Quick Dial Keys

This feature allows you to dial to the contacts in your private phonebook by pressing and holding a quick dial key that you have assigned. You can assign 9 quick dial keys (keys 1-9).

Assign a quick dial key

PRIVATE, and then press OK.

3. Select displayed.

4. Scroll to the quick dial key you wish to use. If no number is assigned to the quick dial key, the display shows EMPTY. To assign a number, press SELECT, If there is already a number assigned to the quick dial key, the display shows the name and number of the contact.

5. To assign a new number press OPTIONS. Select CHANGE.

Press OK. The display shows the list of contacts in your private phonebook. the

7. Press that you selected. Press OK to confirm.

186

Delete a quick dial key

Press NAMES.

Select PRIVATE, and then press OK.

Select QUICK DIAL, and then press OK. The first quick dial key is displayed.

Scroll to the quick dial key you wish to delete.

Press OPTIONS. and select DELETE. Press OK.

CONFIRM? is displayed. Press OK to confirm.

Delete a contact from your private phonebook

Press NAMES and select, PRIVATE Press OK.

Select VIEW. Press OK.

Scroll to the contact you wish to delete or search by letter.

Press OPTIONS. Select DETAILS. Press OK. The details of the contact you selected are displayed.

Press OPTIONS.

Select DELETE. Press OK.

CONFIRM? is displayed. Press OK to confirm.

Delete all contacts in your private phonebook

Press NAMES

Select PRIVATE and press OK.

Select DELETE ALL. Press OK. CONFIRM? is displayed. Press OK to confirm.

Status of the private phonebook

Your phone keeps track of how much memory you have used and how much is still available in your phonebook.

Press NAMESS

Select PRIVATE and press OK

Select STATUS. Press OK to view the status. The number of used and free locations are displayed. Press OK when finished.

Call a number in your phonebook

VIEW. Press OK. Scroll to the contact you wish to call or search by letter.

OPTIONS.

DETAILS. Press OK. The details of the contact you selected are displayed.

5. Press

Find out who has called you and whom you have called

Your phone keeps a record each time you make, receive or miss a call. You can access a list of the last 20 calls that you have missed and a list of the last 10 calls you have dialed and the last 10 calls you have received. You can keep track of whom you’ve talked to and for how long.

Check your call records

1. Press the CALLS Key

MISSED, DIALED or RECEIVED.

187

list.

OPTIONS. Select DETAILS. Press OK.

Transfer the call records to your private phonebook

You can transfer the call records to your private phonebook the

2. Select records is displayed. Scroll to the entry you want. To view the details of the call records entry, go to step 3. If not, go to step 4.

OPTIONS. Press to select DETAILS. Press OK.

OPTIONS. Select TO PRIVATE to copy to the private phonebook. Press OK.

5. You must enter a name. Add or edit the name using the keypad. Press CLEAR to erase a character or digit.

6. Press . Add or edit the number using the keypad. Press

CLEAR to erase a digit. There must be a number.

7. Press

View the call timer

the

CALL TIMERS. Press OK.

3. Select

OK. The time you spent on the calls is displayed.

OK when finished.

Reset the call timer

the

CALL TIMERS. Press OK.

3. Select

OK to confirm. The call timer is reset and will start counting from 0 seconds.

Call a number in your call records

While you are reviewing the call records, you can make a call or return a call to the person. the

2. Select

OK. A list of call records is displayed. Scroll to the entry you want.

OPTIONS.

5. Press .

Using your services key

Your handset can store 10 feature codes in the services directory.

Each code can have up to 10 characters for the name and 20 digits for the code. See page 49 for the feature codes.

To store a feature code name and number

1. Press the SER key.

2. Select ADD ENTRY. Press OK. Enter the name for the feature.

You must enter a name.

3. Enter the number for the record. You must enter a number.

188

Press SAVE.

Duplicate name

You cannot enter an identical name for different records in your services directory. If so, DUPLICATE NAME is displayed. Press OK to replace the existing record with the new entry or press CANCEL to return to the previous display and make changes to the name.

Delete all of the services directory

the

2. Select

Press OK.

Call a number in your services directory

the

VIEW. Press OK. The list of services is displayed.

3. Scroll to the service you wish to call or search by letter.

4. Press service you selected are displayed.

5. Press .

Additional features

Keypad lock

Locking the keypad prevents accidental key presses when you put your phone in the pocket.

1. Press and hold LOCK during standby. The keypad is locked.

To unlock the keypad:

UNLOCK. UNLOCK? is displayed. Press OK. The keypad is unlocked.

Screen saver

The screen saver comes on when your phone is inactive for 30 seconds in standby. The screen saver is a clock that shows the current time of your phone.

During screen saver mode, Press any soft key and the phone will go to standby.

Personalizing your phone

Your phone comes with a color display and a selection of ringing melodies.

Personalize your phone’s display

To name your phone:

MENU.

2. Press

HANDSET NAME. Press OK.

4. Enter or edit the name.

5. Press

Change your wallpaper

Change the wallpaper to give your phone a refresh look with your style.

MENU.

189

WALLPAPER. Press OK.

4. Select the wallpaper. Press OK to confirm.

Change the display color

Change the color of the menus, highlight, and background of your phone to your color.

MENU.

2. Select

3. Select

4. Select the color. The color of the menus will change as you select the different colors.

5. Press

Personalize your sounds

You can assign different ringing melodies for each handset at different volume levels.

Your phone also provides key press tones, confirmation tones and

Parking tones.

Key tones are tones that your phone makes each time you press a key on the phone.

Confirmation tones are tones that your phone makes when an operation is successful.

Parking tones are sounded when you place your phone on the base unit for charging.

To set your handset’s ringing melodies and volume:

MENU.

SOUNDS. Press OK.

3. Select HANDSET. Press OK.

4. Press to change the volume level. Press

5. Press to select the melody.

To set your handset’s key tones

MENU.

2. Select Press

3. Select HS KEY TONES. Press OK.

4. Select ON or OFF. Press OK to confirm.

To set your handset’s confirmation/parking tones

MENU.

2. Select

3. Select HS TONES. Press OK.

To set the alarm clock

MENU.

2. Select EXTRAS. Press OK.

3. Select ALARM CLOCK. Press OK.

4. Select ON or OFF.

190

To set the alarm clock on, press OK and continue to step 5.

To set the alarm clock off, press OK to confirm.

5. Press to set the hour. Press .

6. Press to set the minute. If your phone’s time format is set to 12 hours, go to step 7. If it is 24 hours, go to step 8.

7. Press . Press to set AM/PM.

8. Press

When the Alarm Clock rings: -

1. Press STOP to turn off and deactivate the alarm clock

2. Press SNOOZE. The alarm clock will ring again in 10 minutes.

Baby Monitor

When Baby Monitor is set other extensions can call the phone.

The extension automatically answers the call and the caller can listen.

MENU.


3. Select BABY MONITOR. Press OK.

ON.

The display shows BABY MONITOR and the option CANCEL.

To turn Baby Monitor off select CANCEL

CONFIRM? is shown. Select OK.

Timer

The handset will ring after the time you set has elapsed.

1. Press


4. Press to set the HOUR. Press

5. Press to set the MINUTE. Press .

6. Press to set the SECOND.

OK to confirm. The timer starts counting and your can see the timer on display.

The countdown timer will ring once it finishes counting the time you set.

Press STOP. The countdown timer will stop ringing.

.

Stopwatch

EXTRAS. Press OK.

3. Select STOPWATCH. Press OK.

START. The stopwatch starts counting.

Press STOP. The stopwatch stops. You can choose to reset the stopwatch or cancel the stopwatch.

191

Press PAUSE. The stopwatch pauses counting. Press RESUME to start the stopwatch again from the paused time.

Press CANCEL. The stopwatch is deactivated.

Using touch & dial

Touch & dial allows you to call a number by pressing any key

(except CANCEL) on your handset.

MENU.


3. Select TOUCH & DIAL. Press OK.

4. Select ON. Press . Enter the phone number.

If activated, TOUCH & DIAL is displayed.

To deactivate Touch and Dial

Auto answer

Auto answer gives you the convenience of answering a call by just picking up the phone from the base unit or charger.

You do not need to press any key to answer the call.

To activate or deactivate auto answer:

MENU.

2. Select SYSTEM. Press OK

3. Select AUTO ANSWER. Press OK.

4. Select ON or OFF. Press OK.

Language

The handset language can be changed to French or Spanish

1. Press

2. Select SYSTEM. Press OK

3. Select LANGUAGE. Press OK

4. Select the language.

Icons on your handset’s display.

Call in progress

Battery Level

Loudspeaker

Name

Number

Volume level; I block = lowest volume; 3 blocks = highest volume

Mode

Prefix

Volume

192

C

IP Addresses, Network Masks & Subnets

IP Addresses

Note

This section refers only to IP addresses for IPv4 (version 4 of the

Internet Protocol). IPv6 addresses are not covered.

This section assumes basic knowledge of binary numbers, bits, and bytes.

IP addresses, the Internet's version of telephone numbers, are used to identify individual nodes (computers or systems) on the Internet.

Every IP address contains four numbers, each from 0 to 255 and separated by dots (periods), e.g. 20.56.0.211. These numbers are called, from left to right, field1, field2, field3, and field4.

This style of writing IP addresses as decimal numbers separated by dots is called dotted decimal notation. The IP address 20.56.0.211 is read "twenty dot fifty-six dot zero dot two-eleven."

Structure of an IP address

IP addresses have a hierarchical design similar to that of telephone numbers. For example, a 7-digit telephone number starts with a 3digit prefix that identifies a group of thousands of telephone lines, and ends with four digits that identify one specific line in that group.

Similarly, IP addresses contain two kinds of information:

• Network ID

Identifies a particular network within the Internet or intranet

• Host ID

Identifies a particular computer or system on the network

The first part of every IP address contains the network ID, and the rest of the address contains the host ID. The length of the network

ID depends on the network's class (see following section). The table below shows the structure of an IP address.

Field1 Field2 Field3 Field4

Class A Network ID

Class B Network ID

Host ID

Host ID

Class C Network ID Host ID

Here are some examples of valid IP addresses:

Class A: 10.30.6.125 (network = 10, host = 30.6.125)

Class B: 129.88.16.49 (network = 129.88, host = 16.49)

Class C: 192.60.201.11 (network = 192.60.201, host = 11)

Network classes

The three commonly used network classes are A, B, and C. (There is also a class D but it has a special use beyond the scope of this discussion.) These classes have different uses and characteristics.

Class A networks are the Internet's largest networks, each with room for over 16 million hosts. Up to 126 of these huge networks can exist, for a total of over 2 billion hosts. Because of their huge size, these networks are used for WANs and by organizations at the infrastructure level of the Internet, such as your ISP.

193

Definition

mask

Note

Class B networks are smaller but still quite large, each able to hold over 65,000 hosts. There can be up to 16,384 class B networks in existence. A class B network might be appropriate for a large organization such as a business or government agency.

Class C networks are the smallest, only able to hold 254 hosts at most, but the total possible number of class C networks exceeds 2 million (2,097,152 to be exact). LANs connected to the Internet are usually class C networks.

Some important notes regarding IP addresses:

The class can be determined easily from field1: field1 = 1-126: Class A field1 = 128-191: Class B field1 = 192-223: Class C

(field1 values not shown are reserved for special uses)

A host ID can have any value except all fields set to 0 or all fields set to 255, as those values are reserved for special uses.

Subnet masks

A mask looks like a regular IP address, but contains a pattern of bits that tells what parts of an IP address are the network ID and what parts are the host ID: bits set to 1 mean "this bit is part of the network ID" and bits set to 0 mean "this bit is part of the host ID."

Subnet masks are used to define subnets (what you get after dividing a network into smaller pieces). A subnet's network ID is created by "borrowing" one or more bits from the host ID portion of the address. The subnet mask identifies these host ID bits.

For example, consider a class C network 192.168.1. To split this into two subnets, you would use the subnet mask:

255.255.255.128

It's easier to see what's happening if we write this in binary:

11111111. 11111111. 11111111.10000000

As with any class C address, all of the bits in field1 through field3 are part of the network ID, but note how the mask specifies that the first bit in field4 is also included. Since this extra bit has only two values (0 and 1), this means there are two subnets. Each subnet uses the remaining 7 bits in field4 for its host IDs, which range from

1 to 126 hosts (instead of the usual 0 to 255 for a class C address).

Similarly, to split a class C network into four subnets, the mask is:

255.255.255.192 or 11111111. 11111111. 11111111.11000000

The two extra bits in field4 can have four values (00, 01, 10, 11), so there are four subnets. Each subnet uses the remaining six bits in field4 for its host IDs, ranging from 1 to 62.

Sometimes a subnet mask does not specify any additional network ID bits, and thus no subnets. Such a mask is called a

default subnet mask. These masks are:

Class A:

Class B:

Class C:

255.0.0.0

255.255.0.0

255.255.255.0

These are called default because they are used when a network is

initially configured, at which time it has no subnets.

194

D

Glossary

802.11

10BASE-T

100BASE-T

ADSL analog

ATM authenticate binary

DHCP

DHCP relay

DHCP server digital

DNS

A family of specifications for wireless LANs developed by a working group of the IEEE. This in an Ethernet protocol, often called Wi-Fi.

A designation for the type of wiring used by Ethernet networks with a data rate of 10 Mbps. Also known as Category 3 (CAT 3) wiring. See data rate, Ethernet.

A designation for the type of wiring used by Ethernet networks with a data rate of 100 Mbps. Also known as Category 5 (CAT 5) wiring. See data rate, Ethernet.

Asymmetric Digital Subscriber Line

The most commonly deployed "flavor" of DSL for home users is asymmetrical DSL. The term asymmetrical refers to its unequal data rates for downloading and uploading (the download rate is higher than the upload rate). The asymmetrical rates benefit home users because they typically download much more data from the Internet than they upload.

An analog signal is a signal that has had its frequency modified in some way, such as by amplifying its strength or varying its frequency, in order to add information to the signal. The voice component in DSL is an analog signal. See digital.

Asynchronous Transfer Mode

A standard for high-speed transmission of data, text, voice, and video, widely used within the Internet. ATM data rates range from 45 Mbps to 2.5 Gbps. See data rate.

To verify a user’s identity, such as by prompting for a password.

The "base two" system of numbers, that uses only two digits, 0 and 1, to represent all numbers. In binary, the number 1 is written as 1, 2 as 10, 3 as 11, 4 as 100, etc. Although expressed as decimal numbers for convenience, IP addresses in actual use are binary numbers; e.g., the IP address 209.191.4.240 is

11010001.10111111.00000100.11110000 in binary. See bit, IP

address, network mask.

Dynamic Host Configuration Protocol

DHCP automates address assignment and management. When a computer connects to the LAN, DHCP assigns it an IP address from a shared pool of IP addresses; after a specified time limit,

DHCP returns the address to the pool.

Dynamic Host Configuration Protocol relay

A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the Mitel 1000’s interfaces can be configured as a DHCP relay. See DHCP.

Dynamic Host Configuration Protocol server

A DHCP server is a computer that is responsible for assigning IP addresses to the computers on a LAN. See DHCP.

Of data, having a form based on discrete values expressed as binary numbers (0's and 1's). The data component in DSL is a digital signal. See analog.

Domain Name System

The DNS maps domain names into IP addresses. DNS information is distributed hierarchically throughout the Internet among computers called DNS servers. For example,

www.yahoo.com is the domain name associated with IP address

216.115.108.243. When you start to access a web site, a DNS

195

domain name

FTP

Gbps host

HTTP

Hub

ICMP

IEEE

Internet intranet

IP

IP address download

DSL encryption keys

Ethernet

server looks up the requested domain name to find its corresponding IP address. If the DNS server cannot find the IP address, it communicates with higher-level DNS servers to determine the IP address. See domain name.

A domain name is a user-friendly name used in place of its associated IP address. Domain names must be unique; their assignment is controlled by the Internet Corporation for Assigned

Names and Numbers (ICANN). Domain names are a key element of URLs, which identify a specific file at a web site. See

DNS.

To transfer data in the downstream direction, i.e., from the

Internet to the user.

Digital Subscriber Line

A technology that allows both digital data and analog voice signals to travel over existing copper telephone lines.

See network keys

The most commonly installed computer network technology, usually using twisted pair wiring. Ethernet data rates are 10

Mbps and 100 Mbps. See also 10BASE-T, 100BASE-T, twisted

pair.

File Transfer Protocol

A program used to transfer files between computers connected to the Internet. Common uses include uploading new or updated files to a web server, and downloading files from a web server.

Abbreviation of Gigabits per second, or one billion bits per second. Internet data rates are often expressed in Gbps.

A system (usually a computer) connected to a network.

Hyper-Text Transfer Protocol

HTTP is the main protocol used to transfer data from web sites so that it can be displayed by web browsers. See web browser,

web site.

A hub is a place of convergence where data arrives from one or more directions and is forwarded out in one or more directions. It connects an Ethernet bridge/router to a group of PCs on a LAN and allows communication to pass between the networked devices.

Internet Control Message Protocol

An Internet protocol used to report errors and other networkrelated information. The ping command makes use of ICMP.

The Institute of Electrical and Electronics Engineers is a technical professional society that fosters the development of standards that often become national and international standards.

The global collection of interconnected networks used for both private and business communications.

A private, company-internal network that looks like part of the

Internet (users access information using web browsers), but is accessible only by employees.

See TCP/IP.

Internet Protocol address

The address of a host (computer) on the Internet, consisting of four numbers, each from 0 to 255, separated by periods, e.g.,

209.191.4.240. An IP address consists of a network ID that identifies the particular network the host belongs to, and a host

ID uniquely identifying the host itself on that network. A network mask is used to define the network ID and the host ID. Because

IP addresses are difficult to remember, they usually have an

196

ISP

associated domain name that can be specified instead. See

domain name, network mask.

Internet Service Provider

A company that provides Internet access to its customers, usually for a fee.

LAN

Local

A network limited to a small geographic area, such as a home or

LED

small office.

Light Emitting Diode

MAC address

An electronic light-emitting device. The indicator lights on the front of the Mitel 1000 unit are LEDs.

Media Access Control address

The permanent hardware address of a device, assigned by its manufacturer. MAC addresses are expressed as six pairs of hex characters, with each pair separated by colons. For example;

NN:NN:NN:NN:NN:NN.

See network mask.

mask

Mbps

Abbreviation for Megabits per second, or one million bits per second. Network data rates are often expressed in Mbps.

NAT

Network

A service performed by many routers that translates your

network network keys network mask

NIC packet ping pass phrase

network’s publicly known IP address into a private IP address for each computer on your LAN. Only your router and your LAN know these addresses; the outside world sees only the public IP address when talking to a computer on your LAN.

A group of computers that are connected together, allowing them to communicate with each other and share resources, such as software, files, etc. A network can be small, such as a LAN, or very large, such as the Internet.

(Also known as encryption keys.) 64-bit and 128-bit encryption keys used in WEP wireless security schemes. The keys encrypt data over the WLAN, and only wireless PCs configured with WEP keys that correspond to the keys configured on the device can send/receive encrypted data.

A network mask is a sequence of bits applied to an IP address to select the network ID while ignoring the host ID. Bits set to 1 mean "select this bit" while bits set to 0 mean "ignore this bit."

For example, if the network mask 255.255.255.0 is applied to the

IP address 100.10.50.1, the network ID is 100.10.50, and the host ID is 1. See binary, IP address, subnet.

Network Interface Card

An adapter card that plugs into your computer and provides the physical interface to your network cabling. For Ethernet NICs this is typically an RJ-45 connector. See Ethernet, RJ-45.

Data transmitted on a network consists of packets. Each packet contains a payload (the data), plus overhead information such as where it came from (source address) and where it should go

(destination address).

A secret password used in WPA wireless data encryption.

Encryption is based on a WPA master key that is derived from the pass phrase and the network name (SSID) of the device. The pass phrase should be at least 20 characters long in order to deter a hacker attempting to crack the pass phrase by recording a series of frames then trying commonly used passwords offline until one works (known as offline PSK dictionary attacks).

Packet Internet (or Inter-Network) Groper

A program used to verify whether the host associated with an IP

197

address is online. It can also be used to reveal the IP address for

port

PPP

a given domain name.

A physical access point to a device such as a computer or router, through which data flows into and out of the device.

Protocol

PPPoA

PPPoE remote protocol

A protocol for serial data transmission that is used to carry IP

(and other protocol) data between your ISP and your computer.

The WAN interface on the Mitel 1000 uses two forms of PPP called PPPoA and PPPoE. See PPPoA, PPPoE.

Point-to-Point Protocol over ATM

One of the two types of PPP interfaces you can define for a

Virtual Circuit (VC), the other type being PPPoE. You can define only one PPPoA interface per VC.

Point-to-Point Protocol over Ethernet

One of the two types of PPP interfaces you can define for a

Virtual Circuit (VC), the other type being PPPoA. You can define one or more PPPoE interfaces per VC.

A set of rules governing the transmission of data. In order for a data transmission to work, both ends of the connection have to follow the rules of the protocol.

In a physically separate location. For example, an employee

RIP

RJ-11

RJ-45 routing

SDNS

SSID subnet subnet mask

away on travel who logs in to the company’s intranet is a remote user.

Routing Information Protocol

The original TCP/IP routing protocol. There are two versions of

RIP: version I and version II.

Registered Jack Standard-11

The standard plug used to connect telephones, fax machines, modems, etc. to a telephone port. It is a 6-pin connector usually containing four wires.

Registered Jack Standard-45

The 8-pin plug used in transmitting data over phone lines.

Ethernet cabling usually uses this type of connector.

Forwarding data between your network and the Internet on the most efficient route, based on the data’s destination IP address and current network conditions. A device that performs routing is called a router.

Secondary Domain Name System (server)

A DNS server that can be used if the primary DSN server is not available. See DNS.

Service Set Identifier (also known as the Extended Service Set

Identifier (ESSID)) is a unique identifier that differentiates one wireless device from another. Wireless PCs configured with the same SSID can access that device.

A subnet is a portion of a network. The subnet is distinguished from the larger network by a subnet mask that selects some of the computers of the network and excludes all others. The subnet's computers remain physically connected to the rest of the parent network, but they are treated as though they were on a separate network. See network mask.

A mask that defines a subnet. See network mask.

TCP/IP

Transmission Control Protocol/Internet Protocol

The basic protocols used on the Internet. TCP is responsible for dividing data up into packets for delivery and reassembling them at the destination, while IP is responsible for delivering the packets from source to destination. When TCP and IP are

198

Telnet

TFTP

TKIP triggers twisted pair

bundled with higher-level applications such as HTTP, FTP,

Telnet, etc., TCP/IP refers to this whole suite of protocols.

An interactive, character-based program used to access a remote computer. While HTTP (the web protocol) and FTP only allow you to download files from a remote computer, Telnet allows you to log into and use a computer from a remote location.

Trivial File Transfer Protocol

A protocol for file transfers, TFTP is easier to use than File

Transfer Protocol (FTP) but not as capable or secure.

Temporal Key Integrity Protocol (TKIP) provides WPA with a data encryption function. It ensures that a unique master key is generated for each packet, supports message integrity and sequencing rules and supports re-keying mechanisms.

Triggers are used to deal with application protocols that create separate sessions. Some applications, such as NetMeeting, open secondary connections during normal operations, for example, a connection to a server is established using one port, but data transfers are performed on a separate connection. A trigger tells the device to expect these secondary sessions and how to handle them.

Once you set a trigger, the embedded IP address of each incoming packet is replaced by the correct host address so that NAT can translate packets to the correct destination. You can specify whether you want to carry out address replacement, and if so, whether to replace addresses on TCP packets only, UDP packets only, or both.

The ordinary copper telephone wiring used by telephone companies. It contains one or more wire pairs twisted together to reduce inductance and noise. Each telephone line uses one pair.

In homes, it is most often installed with two pairs. For Ethernet

LANs, a higher grade called Category 3 (CAT 3) is used for

10BASE-T networks, and an even higher grade called Category

5 (CAT 5) is used for 100BASE-T networks. See 10BASE-T,

100BASE-T, Ethernet.

unnumbered interfaces

An unnumbered interface is an IP interface that does not have a local subnet associated with it. Instead, it uses a router-id that serves as the source and destination address of packets sent to and from the router. Unlike the IP address of a normal interface, the router-id of an unnumbered interface is allowed to be the

upstream

USB

same as the IP address of another interface. For example, the

WAN unnumbered interface of your Mitel 1000 uses the same IP address of the LAN interface (192.168.1.1).

The unnumbered interface is temporary – PPP or DHCP will assign a ‘real’ IP address automatically.

The direction of data transmission from the user to the Internet.

Universal Serial Bus

A serial interface that lets you connect units such as printers, scanners, etc. to your computer by simply plugging them in.

VC

Virtual

VCI

A connection from your DSL router to your ISP.

Virtual Circuit Identifier

Together with the Virtual Path Identifier (VPI), the VCI uniquely identifies a VC. Your ISP will tell you the VCI for each VC they provide. See VC.

199

VPI

WAN

WEP

Web browser

Web page

Web site

WWW

Wireless

Wireless LAN

WPA

Virtual Path Identifier

Together with the Virtual Circuit Identifier (VCI), the VPI uniquely identifies a VC. Your ISP will tell you the VPI for each VC they provide. See VC.

Wide Area Network

Any network spread over a large geographical area, such as a country or continent. With respect to the Mitel 1000, WAN refers to the Internet.

A software program that uses Hyper-Text Transfer Protocol

(HTTP) to download information from (and upload to) web sites, and displays the information, which may consist of text, graphic images, audio, or video, to the user. Web browsers use Hyper-

Text Transfer Protocol (HTTP). Popular web browsers include

Netscape Navigator and Microsoft Internet Explorer. See HTTP,

web site, WWW.

A web site file typically containing text, graphics and hyperlinks

(cross-references) to the other pages on that web site, as well as to pages on other web sites. When a user accesses a web site, the first page that is displayed is called the home page. See

hyperlink, web site.

A computer on the Internet that distributes information to (and gets information from) remote users through web browsers. A web site typically consists of web pages that contain text, graphics, and hyperlinks. See hyperlink, web page.

Wired Equivalent Privacy (WEP) encrypts data over WLANs. Data is encrypted into blocks of either 64 bits length or 128 bits length.

The encrypted data can only be sent and received by users with access to a private network key. Each PC on your wireless network must be manually configured with the same key as your Mitel 1000 in order to allow wireless encrypted data transmissions.

Eavesdroppers cannot access your network if they do not know your private key. WEP is considered to be a low security option.

Wireless is a term used to describe telecommunications in which electromagnetic waves (rather than some form of wire) carry the signal over part or all of the communication path. See wireless

LAN.

A wireless LAN (WLAN) is one in which a mobile user can connect to a local area network (LAN) through a wireless (radio) connection. A standard, IEEE 802.11, specifies the technologies for wireless LANs.

Wi-Fi Protected Access

WPA is an initiative by the IEEE and Wi-Fi Alliance to address the security limitations of WEP. WPA provides a stronger data encryption method (called Temporal Key Integrity Protocol (TKIP)).

It runs in a special, easy-to-set-up home mode called Pre-Shared

Key (PSK) that allows you to manually enter a pass phrase on all the devices in your wireless network. WPA data encryption is based on a WPA master key. The master key is derived from the pass phrase and the network name (SSID) of the device.

It provides improved data encryption and stronger user authentication. The mode of WPA supported on your Mitel 1000 is called Pre-Shared Key (PSK), which allows you to manually enter a type of key called a pass phrase.

World Wide Web

Also called (the) Web. Collective term for all web sites anywhere in the world that can be accessed via the Internet.

200

E

Configuring your PCs

This appendix provides instructions for configuring the Internet settings on your computers to work with Mitel 1000.

Configuring Ethernet PCs

To configure your PC to automatically obtain an IP address

By default, Mitel 1000 automatically assigns the required Internet settings to your PCs. You need to configure the PCs to accept this information when it is assigned.

If you have connected your LAN PCs via Ethernet to Mitel 1000, follow the instructions that correspond to the operating system installed on your PC:

If you want to allow Wireless PCs to access your Mitel 1000, see section on Wireless Setup / Security on page 122.

Windows® XP PCs

1. In the Windows task bar, click the Start button, and then click

Control Panel.

2. Double-click the Network Connections icon. the icon corresponding to your network interface card (NIC) and select Properties. (Often, this icon is labeled Local Area

Connection).

The Local Area Connection dialog box is displayed with a list of currently installed network items.

4. Ensure that the check box to the left of the item labeled Internet

Protocol TCP/IP is checked and click Properties.

5. In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labeled Obtain an IP address automatically. Also click the radio button labeled Obtain DNS server address automatically.

6. Click OK twice to confirm your changes, and then close the

Control Panel.

Windows 2000 PCs

First, check for the IP protocol and, if necessary, install it:

1. In the Windows task bar, click the Start button, point to

Settings, and then click Control Panel.

2. Double-click the Network and Dial-up Connections icon.

Local Area Connection icon, and then select Properties.

The Local Area Connection Properties dialog box is displayed with a list of currently installed network components. If the list includes

Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step 10.

4. If Internet Protocol (TCP/IP) does not display as an installed component, click Install…

201

Protocol, and then click Add… and then click OK. installation CD or other media. Follow the instructions to install the files. prompted, settings.

Next, configure the PCs to accept IP information assigned by Mitel

1000: the

Connections icon.

10. In the Network and Dial-up Connections window, right-click the

Local Area Connection icon, and then select Properties.

11. In the Local Area Connection Properties dialog box, select

Internet Protocol (TCP/IP), and then click Properties.

12. In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labeled Obtain an IP address automatically. Also click the radio button labeled Obtain DNS server address

automatically.

13. Click OK twice to confirm and save your changes, and then close the Control Panel.

Windows Me PCs



2. Double-click the Network and Dial-up Connections icon.

Network icon, and then select Properties.

The Network Properties dialog box displays with a list of currently installed network components. If the list includes Internet Protocol

(TCP/IP), then the protocol has already been enabled. Skip to step

11.

4. If Internet Protocol (TCP/IP) does not display as an installed component, click Add… the

Protocol, and then click Add…

Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK.

You may be prompted to install files from your Windows Me installation CD or other media. Follow the instructions to install the files. prompted, settings.

9. Next, configure the PCs to accept IP information assigned by

Mitel 1000:

10. In the Control Panel, double-click the Network and Dial-up

Connections icon.

202

11. In Network and Dial-up Connections window, right-click the

Network icon, and then select Properties.

12. In the Network Properties dialog box, select TCP/IP, and then click Properties.

13. In the TCP/IP Settings dialog box, click the radio button labeled

Server

assigned IP address. Also click the radio button labeled

Server assigned name server address.

14. Click OK twice to confirm and save your changes, and then close the Control Panel.

Windows 95, 98 PCs




2. Double-click the Network icon.

The Network dialog box displays with a list of currently installed network components. If the list includes TCP/IP, and then the protocol has already been enabled. Skip to step 8.

3. If TCP/IP does not display as an installed component, click

Add…

on

TCP/IP in the Network Protocols list box.

OK to return to the Network dialog box, and then click OK again.

8. You may be prompted to install files from your Windows 95/98 installation CD. Follow the instructions to install the files.

Next, configure the PCs to accept IP information assigned by Mitel

1000:

10. Open the Control Panel window, and then click the Network icon.

11. Select the network component labeled TCP/IP, and then click

Properties.

If you have multiple TCP/IP listings, select the listing associated with your network card or adapter.

12. In the TCP/IP Properties dialog box, click the IP Address tab.

13. Click the radio button labeled Obtain an IP address

automatically.

14. Click the DNS Configuration tab, and then click the radio button labeled Enable DNS.

15. Click OK twice to confirm and save your changes.

You will be prompted to restart Windows.

16. Click Yes.

Windows NT 4.0 workstations


1. In the Windows NT task bar, click the Start button, point to


2. In the Control Panel window, double click the Network icon.

203

The Protocols tab displays a list of currently installed network protocols. If the list includes TCP/IP, then the protocol has already been enabled. Skip to step 9.

4. If TCP/IP does not display as an installed component, click

Add… the then click OK.

You may be prompted to install files from your Windows NT installation CD or other media. Follow the instructions to install the files.

After all files are installed, a window displays to inform you that a

TCP/IP service called DHCP can be set up to dynamically assign IP information.

Yes to continue, and then click OK if prompted to restart your computer.

7. Next, configure the PCs to accept IP information assigned by

Mitel 1000:

8. Open the Control Panel window, and then double-click the

Network icon.

10. In the Protocols tab, select TCP/IP, and then click Properties.

11. In the Microsoft TCP/IP Properties dialog box, click the radio button labeled Obtain an IP address from a DHCP server.

12. Click OK twice to confirm and save your changes, and then close the Control Panel.

Assigning static Internet information to your PCs

If you are a typical user, you will not need to assign static Internet information to your LAN PCs because your ISP automatically assigns this information for you.

In some cases however, you may want to assign Internet information to some or all of your PCs directly (often called

“statically”), rather than allowing Mitel 1000 to assign it. This option may be desirable (but not required) if:

You have obtained one or more public IP addresses that you want to always associate with specific computers (for example, if you are using a computer as a public web server).

You maintain different subnets on your LAN (subnets are described in Appendix C).

Before you begin, you must have the following information available:

The IP address and subnet mask of each PC

The IP address of the default gateway for your LAN. In most cases, this is the address assigned to the LAN port on Mitel 1000.

By default, the LAN port is assigned the IP address 192.168.1.1.

(You can change this number or another number can be assigned by your ISP.)

The IP address of your ISP’s Domain Name System (DNS) server.

On each PC to which you want to assign static information, follow the instructions relating only to checking for and/or installing the IP protocol. Once it is installed, continue to follow the instructions for displaying each of the Internet Protocol (TCP/IP) properties. Instead of enabling dynamic assignment of the IP addresses for the

204

Note

computer, DNS server and default gateway, click the radio buttons that enable you to enter the information manually.

Your PCs must have IP addresses that place them in the same subnet as the LAN port.

Setting up your browser not to use a proxy server

1. Launch Internet Explorer.

2. Select Tools, Internet Options.

3. Select Connections

If you have been using a dial up connection ensure the button Never

dial a connection is selected

4. Select LAN Settings.

5. Under Proxy Server, ensure that Use a proxy server for your

LAN is unchecked.

205

F

Troubleshooting

This appendix takes you through a step-by-step procedure to help you resolve problems that you may encounter when installing or using Mitel 1000.

Cannot browse the Internet

(1) Check the LEDs on the Mitel 1000 front panel

(a)

Is the Power

LED on?

(b)

For a wired PC

Is the Ethernet

LED on?

Yes

No

Yes

No

Go to (b)

Verify that you are using the power cable provided and that it is securely connected to Mitel 1000 and a wall socket/power strip.

Go to (d)

Verify that your PC is connected to LAN port 1, 2, 3 or 4 on the Mitel 1000 using a

Cat 5 patch cord or cable.

(c)

For a Wireless

PC

Is the Wireless

LED Green?

(d)

Is the DSL

LED on steady?

Yes

No

Go to (d)

Go to (4) Check your WLAN settings

(e)

Is the Internet

LED Green?

Yes

No

Go to (e)

The LED is flashing

Verify that the ADSL port on the Mitel 1000 is connected to the computer port on the splitter, and that the line port on the splitter is connected to the telephone line.

If the above connections are correct, report the problem to your ADSL service provider.

Yes

Go to (3) Check your PC settings

No

The LED is Red.

Go to (2) Check your ADSL settings.

206

(2) Check your ADSL settings

(a)

Enter the Mitel 1000 Main menu

•

Select Router Configuration

•

Select ADSL Modem click Change the ADSL Modem settings here …

•

Select PPPoA click Next

•

Enter PPP Username, PPP Password, retype password click Next

•

Select Manual enter VPI = 0, VCI = 35 click Next

•

Click Confirm Changes

(b)

Is the Internet

LED on the Mitel

1000 front panel

Green?

Yes

No

Go to (c)

The LED is Red

Contact your ADSL service provider and confirm that your PPP Username and

Password are correct.

(c)

Can you browse?

No

Go to (3) Check your PC settings.

(3) Check your PC settings

Configuring the PC settings for Windows XP are described below. For other operating systems, refer to Appendix D, Configuring your PCs.

•

Click start

•

Click Control Panel

•

Double click Network Connections icon

•

Double click Local Area Connection

•

Under General tab click Properties

•

Under General tab scroll down and highlight Internet Protocol (TCP/IP) click Properties

•

Under General tab select Obtain an IP address automatically select Obtain DNS server address automatically click OK

207

(4) Check your WLAN settings

The following procedure assumes that the WLAN has been set up with

WPA security.

If a different security configuration has been set up, refer back to

Section 10 Wireless Setup/Security

(a)

Enter the Mitel 1000 Main menu

•

Select Wireless Settings/Security

In General Settings

(b)

Is Wireless network enabled ?

Yes

No

Go to (c)

•

Click Enable or disable the wireless network here …

•

Select Enable

•

Click Next

•

Go to (c)

(c)

Make a note of the Network Name

(d)

Select

Allow Mitel 1000 to select a channel

(e)

Select

Wi-Fi Protected Access (WPA) on the wireless network

Enable SSID Broadcast

(f)

Re-enter the Pass Phrase and make a note of it

(g)

Select

Allow any Wireless PCs to connect

Confirm changes


(h)

Is the Wireless

LED on the Micro

Green ?

Yes

Go to (1d)

settings

208

(5) Check your Wireless PC settings

The following procedure is for a PC with an Intel (PRO) Wireless

Network adapter that has been set up for WPA security.

For other Wireless Network adapters, consult the manufacturer’s user manual. Note that some older wireless adapters do not support WPA.

•

Click start

•

Click Control Panel

•

Double click Network Connections icon

•

Double click Wireless Network Connection

•

Under General tab click Properties

•

Select Wireless Network tab highlight the network name noted in (4c) click Properties

•

Under Association tab set Network Association to WPA-PSK set Data Encryption to TKIP re-enter the Network Key (this is the Pass Phrase noted in (4f)) confirm the Network Key click OK

209

Troubleshooting your Cordless Phone

Problem(s) Possible Causes

No dialing tone when pressing .

icon is flashing.

When the handset is placed on the charger, no beep is heard.

Battery icon remains empty although the handset has charged for 24 hours.

You are too far from the base unit.

- Battery is low (low battery icon is displayed).

- The handset is not registered.

If the handset is unregistered, it displays UNREGISTERED.

- The handset is out of range.

- The handset is not placed properly on the base unit or charger.

- The charging contacts are dirty.

- The handset tone is turned off.

- The handset’s power is turned off before placing it on the charger.

- Handset battery is defective.

- Handset is not placed properly on the base unit or charger.

No symbol on the display.

Bad audio quality

(crackles, echo, etc.)

The phone does not ring when a call comes in.

- Battery is uncharged.

- Interference from nearby electrical appliance.

- Mitel 1000 unit is installed in a room with thick walls.

- The handset is too far from the base unit.

- The ringer is turned off.

- The phone is not programmed to ring

Solutions

Move closer to the base unit.

Charge the battery.

- Register the handset.

See page 14

- Move closer to the base unit.

- Take the handset off the base unit and put it back again.

- Clean the charging contacts with a clean and dry cloth.

- Turn on the handset tone from the Sounds

Menu.

- Please contact your supplier to purchase a new rechargeable battery.

- Check to make sure the battery icon is scrolling.

- Charge battery.

- Try plugging the base unit to a different location.

- Install the base unit in a different room.

- Move closer to the base unit.

- Turn on the ringer.

- Program the phone to ring for Incoming Calls.

See Page 94 or 164.

210

Troubleshooting the PABX

No incoming calls

Check that all phones programmed to ring are not programmed for

DND or Forward.

External calls blocked

If you cannot get outgoing access on a 2-wire telephone, move a

Featurephone to the extension. If it shows EXTN LOCK, the extension has been locked and you will need the unlock code to unlock it. See extension lock on Page 59.

No extension dial tone

Check that the extension has not been disconnected through programming. See page 102 for programming from the management application and page 178 for programming from the programming Featurephone.

Not seizing a line for outgoing calls

Check if the line is equipped in programming. See page 107 for programming from the management application and Page 178 for programming from the programming Featurephone.

Check that the key is programmed for line access, see

Featurephone key programming on page 36.

Doorphone not operating

Check the programming for the doorphone see Page 97 for programming from the web management application and Page 176 for programming from the programming Featurephone.

Phone reset

Remember the simple phone reset code 739, which can be dialed from any extension phone.

Caller ID Store is showing answered calls only. I want all calls to be shown

With Caller ID activated in both the telephone exchange and on the

Mitel 1000 you can choose to have all incoming callers telephone numbers added to a ‘Caller ID Store' or just the unanswered calls.

These can be viewed on the Mitel 1000 Featurephone.

In default the system is set to only store unanswered calls.

This can be changed in System Programming see page 160.

Power Fail problems

If there is no electrical mains power connected to your Mitel 1000 and you wish to make or receive external calls, you will need to connect a standard telephone in to the Power Fail socket found on the back of the Mitel 1000. There will be no internal service, no

Broadband connection, Wireless LAN access or Cordless telephone service until the power is restored.

Caller ID is not working

For Caller ID service to work on standard CO lines it has to be enabled in both the telephone exchange and on the Mitel 1000 system. If the service is provided on the CO line it must be programmed in the Mitel 1000. See page 108 for programming from

211

the Management Application and Page 181 for programming from the programming Featurephone.

When setting the system time it does not update immediately

The time and date will not change until all external calls in progress when the programming change is made have finished.

Is there any way of retrieving deleted messages?

Unfortunately there is no facility to retrieve DELETED Voicemail messages.

Noise from the Featurephone speaker

.

There is an option on the Mitel 1000 to play the music you provide for music on hold through the Featurephone speakers when the

Featurephone is not being used. This feature can only be used when you provide an external music source. If the feature is turned on and an external music source is not provided the

Featurephone speakers may make a low-level noise. To stop this, program the feature off. Do this by selecting the Program key on the Featurephone, scroll down and select 'Background music' and select the 'OFF' option.

Featurephone not working in another extension

If the Mitel 1000 system wiring has been extended a Featurephone can only be connected to any of the other hard-wired extensions if the correct wires have been extended through to the telephone socket. The Featurephone requires more wires to work than an ordinary telephone. See page 16 for wiring instructions.

Featurephone ‘Speakerphone’ does not appear to work

The Featurephone has probably been programmed for headset use. Select the Program key and scroll to Headset mode. Select

Headset mode and select Headset off. Headset mode should only be set on when a headset is connected to the headset connection on the Featurephone and this is to be used instead of the handset.

212

www.mitel.com

Global Headquarters

Tel: +1(613) 592-2122

Fax: +1(613) 592-4784

U.S.

Tel: +1(480) 961-9000

Fax: +1(480) 961-1370

EMEA

Tel: +44(0)1291-430000

Fax: +44(0)1291-430400

CALA

Tel: +1(613) 592-2122

Fax: +1(613) 592-7825

Asia Pacific

Tel: +852 2508 9780

Fax: +852 2508 9232

For more information on our worldwide office locations, visit our website at www.mitel.com/offices

THIS DOCUMENT IS PROVIDED TO YOU FOR INFORMATIONAL PURPOSES ONLY. The information furnished in this document, believed by Mitel to be accurate as of the date of its publication, is subject to change without notice. Mitel assumes no responsibility for any errors or omissions in this document and shall have no obligation to you as a result of having made this document available to you or based upon the information it contains.

M MITEL (design) is a registered trademark of Mitel Networks Corporation. All other products and services are the registered trademarks of their respective holders.

© Copyright 2008, Mitel Networks Corporation. All Rights Reserved.

Mitel Superset 1000 Owner's Manual

Owner’s Manual

Table of Contents

Introduction

Save These Instructions.

Use only 26 AWG line cord or larger for

Central Office line connections.

Mode of Operation

USOC Jack

Port FIC SOC

USOC

REN

Getting to know your Mitel 1000

Connecting your Mitel 1000

Basic programming using the Management

Application

Using Your Mitel 1000 Phone System

Connecting to the Internet

PABX Configuration using the web interface

Advanced Router Settings

WAN

F/W

LAN

F/W F/W

DMZ

Configuring Your Mitel 1000 via the

Featurephone

Cordless Phone Detailed Instructions

IP Addresses, Network Masks & Subnets

Glossary

Configuring your PCs

Troubleshooting

www.mitel.com

Related manuals

Table of contents

Mitel Superset 1000 Owner's Manual

Owner’s Manual

Table of Contents

Introduction

Save These Instructions.

Use only 26 AWG line cord or larger for

Central Office line connections.

Mode of Operation

USOC Jack

Port FIC SOC

USOC

REN

Getting to know your Mitel 1000

Connecting your Mitel 1000

Basic programming using the Management

Application

Using Your Mitel 1000 Phone System

Connecting to the Internet

PABX Configuration using the web interface

Advanced Router Settings

WAN

F/W

LAN

F/W F/W

DMZ

Configuring Your Mitel 1000 via the

Featurephone

Cordless Phone Detailed Instructions

IP Addresses, Network Masks & Subnets

Glossary

Configuring your PCs

Troubleshooting

www.mitel.com

Related manuals

Mitel

5201

Mitel

1000 guide

D-Link

KA2PH-540

Mitel

5606

Mitel

6800 Series

Table of contents