Honda 2010 FOURTRAX RANCHER Owner's Manual

０９／０５／１１１４：４０：３３３１ＨＰ４８３００００１

This manual should be considered a permanent part of the ATV and should remain with the ATV when it is resold.

This Owner’s Manual covers the

TRX420FPE

TRX420TE , TRX420FE and models. You may find descriptions of equipment and features that are not on your particular model. All illustrations are based on the TRX420FPE model.

This publication includes the latest production information available before printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation.

No part of this publication may be reproduced without written permission.

The vehicle pictured on the front cover may not match your vehicle.

Honda Motor Co., Ltd. 2009

０９／０５／１１１４：４０：３８３１ＨＰ４８３００００２

2010

Honda

TRX420TE

TRX420FE ES 4

×

4

TRX420FPE ES 4

×

4 with Power Steering

FOURTRAX RANCHER

OWNER’S MANUAL

FOR OFF-ROAD USE ONLY

This vehicle is designed and manufactured for off-road use only.

It conforms to US EPA Noise Emission regulations, but does not conform to Federal Motor Vehicle Safety Standards or US EPA On

Highway Exhaust Emission regulations, and operation on public streets, roads, or highways is illegal. The vehicle is equipped with a USDA qualified spark arrester. Obey local laws and regulations.

It conforms to US EPA and California emission regulations for ATVs.

０９／０５／１１１４：４０：４６３１ＨＰ４８３００００３

Introduction

Congratulations on choosing your Honda ATV.

When you own a Honda, you’re part of a worldwide family of satisfied customers − people who appreciate Honda’s reputation for building quality into every product.

Your Honda was designed as a recreational ATV for off-road use by one rider only.

Before riding, take time to get acquainted with your ATV and how it works. To protect your investment, we urge you to take responsibility for keeping your ATV well maintained. Scheduled service is a must, of course. But it’s just as important to observe the break-in guidelines, and perform all pre-ride and other periodic checks detailed in this manual.

We also recommend that you read this owner’s manual before you ride.

It’s full of facts, instructions, safety information, and helpful tips. To make it easy to use, the manual contains a detailed list of topics at the beginning of each section, and both an in-depth table of contents and an index at the back of the book.

As you read this manual, you will find information that is preceded by a symbol. This information is intended to help you avoid damage to your Honda, other property, or the environment.

Read the Warranties Booklet (page 227 ) thoroughly so you understand the coverages that protect your new Honda and are aware of your rights and responsibilities.

Whenever you ride, tread lightly. By staying on established trails and riding only in approved areas, you help protect the environment and keep off-road riding areas open for the future.

Introduction

０９／０５／１１１４：４０：５３３１ＨＰ４８３００００４

Introduction

If you have any questions, or if you ever need special service or repairs, remember that your Honda dealer knows your ATV best and is dedicated to your complete satisfaction.

Please report any change of address or ownership to your Honda dealer so we will be able to contact you concerning important product information.

You may also want to visit our website at www.honda.com.

Happy riding!

California Proposition 65 Warning

WARNING:

This product contains or emits chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

Introduction

０９／０５／１１１４：４０：５９３１ＨＰ４８３００００５

A Few Words About Safety

Your safety, and the safety of others, is very important. And operating this ATV safely is an important responsibility.

To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.

This information alerts you to potential hazards that could hurt you or others.

Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining an ATV. You must use your own good judgment.

You will find important safety information in a variety of forms, including:

Safety Labels

–– on the ATV.

Safety Messages

–– preceded by a safety alert symbol and one of three signal words:

DANGER, WARNING,

or

CAUTION

.


０９／０５／１１１４：４１：０６３１ＨＰ４８３００００６


These signal words mean:

You WILL be KILLED or

SERIOUSLY HURT if you don’t follow instructions.

You CAN be KILLED or SERIOUSLY

HURT if you don’t follow instructions.

You CAN be HURT if you don’t follow instructions.

Safety Headings

–– such as Important Safety Reminders or Important

Safety Precautions.

Safety Section

–– such as ATV Safety.

Instructions

–– how to use this ATV correctly and safely.

This entire manual is filled with important safety information –– please read it carefully.


０９／０５／１１１４：４１：１６３１ＨＰ４８３００００７

Contents

These pages give an overview of the contents of your owner’s manual.

The first page of each section lists the topics covered in that section.

ATV Safety .......................................................................................

Important safety information you should know, plus a look at the

.

safety related labels on your ATV.

1

Instruments & Controls ...................................................................

.

The location and function of indicators and controls on your ATV and operating instructions for various controls and features.

9

Before Riding ....................................................................................

.

37

The importance of wearing a helmet and other protective gear, how to make sure you and your ATV are ready to ride, and important information about loading.

Basic Operation & Riding ...............................................................

.

How to start and stop the engine, shift gears, and brake. Also, riding

53

precautions.

Contents

０９／０５／１１１４：４１：２９３１ＨＰ４８３００００８

Contents

Servicing Your Honda .....................................................................

.

Why your ATV needs regular maintenance, what you need to know

85

before servicing your Honda, an owner maintenance schedule, and instructions for specific maintenance and adjustment items.

Tips ....................................................................................................

.

173

How to store and transport your ATV and how to be an environmentally responsible rider.

Taking Care of the Unexpected ......................................................

.

183

What to do if you have a flat tire, your engine won’t start, etc.

Technical Information .....................................................................

.

207

ID numbers, technical specifications, and other technical facts.

Consumer Information ....................................................................

.

223

Information on warranties, emission controls, how to get Honda service manuals.

Index ..................................................................................................

.

232

Quick Reference

Handy facts about fuel, engine oil, tire sizes, and air pressures.

Contents

０９／０５／１１１４：４１：３１３１ＨＰ４８３００００９

０９／０５／１１１４：４１：３７３１ＨＰ４８３０００１０

ATV Safety

This section presents some of the most important information and recommendations to help you ride your ATV safely. Please take a few moments to read these pages. This section also includes information about the location of safety labels on your ATV.

Important Safety Information ...............................................................

.

Safety Labels .........................................................................................

.

2

5

ATV Safety

1

０９／０５／１１１４：４１：４６３１ＨＰ４８３０００１１

Important Safety Information

Your ATV can provide many years of service and pleasure if you take responsibility for your own safety and understand the challenges you can meet while riding.

There is much that you can do to protect yourself when you ride. You’ll find many helpful recommendations throughout this manual. The following are a few that we consider to be most important.

Follow the Age Recommendation

The minimum recommended age for this ATV model is 16. Children under age 16 should never operate this vehicle. Refer to the age warnings provided in this manual and on the ATV.

Always Wear a Helmet

It’s a proven fact: helmets significantly reduce the number and severity of head injuries. So always wear an approved motorcycle helmet. We also recommend that you wear eye protection, sturdy boots, gloves, and other protective gear (page 38 ).

Never Carry a Passenger

Your ATV is designed for one person only. There are no handholds, footrests, or seat for a second person, so never carry a passenger. A passenger could interfere with your ability to move around to maintain your balance and control of the ATV.

2

ATV Safety

０９／０５／１１１４：４１：５３３１ＨＰ４８３０００１２


Ride Off-road Only

Your ATV is designed and manufactured for off-road use only. The tires are not made for pavement, and the ATV does not have turn signals and other features required for use on public roads. If you need to cross a paved or public road, get off and walk your ATV across.

Take Time to Learn & Practice

Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.

Because many crashes involve inexperienced or untrained riders, we urge all riders to take a ATV operator course approved by the ATV

Safety Institute (ASI). See page 40 .

Contact an authorized ATV dealer or call 1-800-887-2887 to find out about the training courses nearest you.

Be Alert for Off-road Hazards

The terrain can present a variety of challenges when you ride off-road.

Continually ‘‘read’’ the terrain for unexpected turns, drop-offs, rocks, ruts, and other hazards. Always keep your speed low enough to allow time to see and react to hazards.

ATV Safety

3

０９／０５／１１１４：４２：０１３１ＨＰ４８３０００１３


Ride within Your Limits

Pushing limits is another major cause of ATV crashes. Never ride beyond your personal abilities or faster than conditions warrant.

Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgments and ride safely.

Don’t Drink and Ride

Alcohol and riding don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and ride, and don’t let your friends drink and ride either.

Keep Your Honda in Safe Condition

It’s important to keep your ATV properly maintained and in safe riding condition. Having a breakdown can be difficult, especially if you are stranded off-road far from your base. To help avoid problems, inspect your ATV before every ride and perform all recommended maintenance.

4

ATV Safety

０９／０５／１１１４：４２：０５３１ＨＰ４８３０００１４

Safety Labels

Your ATV comes with a hang tag and several labels containing important safety information. Anyone who rides the vehicle should read and understand this information before riding.

The labels should be considered permanent parts of the vehicle. If a label comes off or becomes hard to read, contact your Honda dealer for replacements.

ATV Safety

5

０９／０５／１１１４：４２：１６３１ＨＰ４８３０００１５

Safety Labels

6

ATV Safety

０９／０５／１１１４：４２：３２３１ＨＰ４８３０００１６

Safety Labels

(TRX420TE, TRX420FE)

(TRX420FPE)

ATV Safety

7

０９／０５／１１１４：４２：４４３１ＨＰ４８３０００１７

Safety Labels

(Except TRX420TE)

8

ATV Safety

０９／０５／１１１４：４２：５５３１ＨＰ４８３０００１８

Instruments & Controls

This section shows the location of all indicators and controls you would normally use before or while riding your ATV.

The items listed on this page are described in this section. Instructions for other components are presented in other sections of this manual where they will be most useful.

Operation Component Locations ..........................................................

.

11

Indicators & Displays ............................................................................

.

14

Multi-function Display ......................................................................

.

18

Gear Position Indicator ......................................................................

.

19

Oil Change Indicator .........................................................................

.

20

Odometer ...........................................................................................

.

21

Tripmeter ...........................................................................................

.

21

Hourmeter .........................................................................................

.

22

Fuel Gauge ........................................................................................

.

23

(cont’d)


9

０９／０５／１１１４：４３：１１３１ＨＰ４８３０００１９


Controls & Features ..............................................................................

.

24

Fuel Valve .........................................................................................

.

24

Ignition Switch ..................................................................................

.

25

2WD/4WD Select Lever (Except TRX420TE ) .............................

.

26

Start Button .......................................................................................

.

27

Engine Stop Switch ...........................................................................

.

27

Headlight Switch ...............................................................................

.

28

Headlight Dimmer Switch .................................................................

.

28

Throttle Lever ...................................................................................

.

29

Gearshift Switch ................................................................................

.

30

Reverse Selector Knob ......................................................................

.

31

Front Brake Lever .............................................................................

.

32

Rear Brake Lever/Parking Brake Lever ............................................

.

32

Rear Brake Pedal ...............................................................................

.

32

Parking Brake ....................................................................................

.

33

Flag Pole Bracket ..............................................................................

.

34

Trailer Hitch ......................................................................................

.

35

PS (Electric Power Steering) ( TRX420FPE only) ...........................

.

36

10


０９／０５／１１１４：４３：１８３１ＨＰ４８３０００２０

Operation Component Locations

reverse selector knob parking brake lock lever headlight dimmer switch headlight switch rear brake lever/ parking brake lever front brake lever gearshift switches start button engine stop switch throttle lever ignition switch

2WD/4WD select lever

(Except TRX420TE)


11

０９／０５／１１１４：４３：２３３１ＨＰ４８３０００２１


rear cargo rack seat latch front cargo rack rear brake pedal fuel valve

12


０９／０５／１１１４：４３：２８３１ＨＰ４８３０００２２


flag pole bracket trailer hitch


13

０９／０５／１１１４：４３：３６３１ＨＰ４８３０００２３

Indicators & Displays

The indicators and displays on your ATV keep you informed, alert you to possible problems, and make your riding safer and more enjoyable.

Refer to the indicators frequently. Their functions are described on the following pages.

(1) (2)

(3) (4) (5) (6)

(7)

(8)

(1) reverse indicator

(2) neutral indicator

(3) PS (Electric Power Steering) indicator (TRX420FPE only)

(4) 4WD indicator

(Except TRX420TE)

(5) high coolant temperature indicator

(6) PGM-FI indicator

(7) multi-function display

(8) hourmeter/odometer/ tripmeter select button

Lamp Check

The high coolant temperature indicator and PGM-FI indicator come on for a few seconds and then go off when you turn the ignition switch ON

( ).

TRX420FPE only:

The PS (Electric Power Steering) indicator comes on when you turn the ignition switch ON ( ) so you can check that it is working.

The indicator remains on until the engine is started.

14


０９／０５／１１１４：４３：４６３１ＨＰ４８３０００２４


The indicators are identified in the table on page 16 with the words:

Lamp Check.

When applicable, the reverse or neutral indicators come on when you turn the ignition switch ON ( ) and remain on until you shift out of reverse or neutral.

Except TRX420TE:

When applicable, the 4WD indicator comes on when you turn the ignition switch ON ( ) and remains on until you shift out of 4WD mode.

If one of these indicators does not come on when it should, have your

Honda dealer check for problems.

Display Check

When the ignition switch is turned ON ( ), the multi-function display make sure the liquid crystal display is functioning properly.

The displays are identified in the table on page 17 with the words:

Display Check.

If any part of these displays does not come on when it should, have your

Honda dealer check for problems.

(1)



15

０９／０５／１１１４：４３：５８３１ＨＰ４８３０００２５

1

2

3


4

5

6

Reverse indicator

Neutral indicator

PS (Electric Power

Steering) indicator

(TRX420FPE only)

4WD indicator

(Except TRX420TE)

High coolant temperature indicator

PGM-FI indicator

Lights when the transmission is in reverse.

neutral.

Lamp Check

Lights when the transmission is in

Lamp Check

Lights when there is an abnormality in the PS (Electric Power Steering) system. See page 36 .

Lamp Check.

Lights when the 4WD drive mode engages.

Lamp Check

.

Lights when coolant temperature is high enough to adversely affect the service life of the engine.

If the high coolant temperature indicator comes on while you are riding, immediately bring the vehicle to a stop, turn the engine off and let it cool. See page 196 .

Lamp Check.

Lights when there is any abnormality in the PGM-FI (Programmed Fuel

Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned

ON ( ). If the indicator comes on at any other time, reduce speed and take your vehicle to a Honda dealer as soon as possible.

Lamp Check.

16


０９／０５／１１１４：４４：１３３１ＨＰ４８３０００２６

7

8

Multi-function display

Gear position indicator

Oil change indicator

Speedometer

Odometer

Tripmeter

Hourmeter

Hourmeter/ odometer/tripmeter select button


The display includes the following functions.

Display Check.

Shows the gear position (page 19 ).

Lights when specified maintenance interval for engine oil change is reached (page 20 ).

Shows riding speed.

Shows accumulated mileage

(page 21 ).

Shows mileage per trip (page 21 ).

Shows hours and tenths of hours of engine operation (page 22 ).

Selects display of the odometer or tripmeter or hourmeter. Resets the tripmeter to zero (0) (page 21 ). This button also used to reset the oil change indicator (page 20 ).


17

０９／０５／１１１４：４４：２０３１ＨＰ４８３０００２７


Multi-function Display

Gear position indicator

Oil change indicator

Speedometer

Odometer

Tripmeter

Hourmeter

(3)

(2)

(4)

(1)


(2) gear position indicator

(3) oil change indicator

(5)

(4) speedometer

(5) odometer/tripmeter/ hourmeter

18


０９／０５／１１１４：４４：２９３１ＨＰ４８３０００２８


Gear Position Indicator

ignition switch is in the ON ( ) position.

The indicator displays: N for neutral, R for reverse, and five forward gears.

1 − 5 for the

‘‘

−

’’ will be displayed on the gear position indicator when the transmission is not shifted into gear properly. Before riding, check that the gear position is properly displayed on the gear position indicator.

If the gear position indicator shows ‘‘

−

’’ or blinks, turn the ignition switch to the OFF ( ) position, and then turn it back to the ON ( ) position again.

If the gear position indicator shows ‘‘ − ’’, rock the vehicle back and forth and make sure the gear position indicator is displayed properly and then if the gear position indicator still shows ‘‘ − ’’ or blinks, see your

Honda dealer.

(1)

(1) gear position indicator


19

０９／０５／１１１４：４４：３８３１ＨＰ４８３０００２９


Oil Change Indicator

operating hours on your ATV approaches the oil change interval specified on the maintenance schedule.

Reset the indicator after each oil change.

To reset the indicator, press and hold the hourmeter/odometer/tripmeter than 5 seconds. The indicator message will disappear.

If the oil is changed before the oil change indicator appears, be sure to reset the oil change indicator after changing the oil, except after the initial oil change.

Press and hold the hourmeter/odometer/tripmeter select button and turn the ignition switch to ON ( ) for more than 5 seconds. When the indicator lights for 2 seconds and then turns off, the oil change indicator is reset.

(1) ON

20

(2)

(1) oil change indicator


(3) ignition switch


ON

(3)

０９／０５／１１１４：４４：４７３１ＨＰ４８３０００３０


Odometer

miles while the ignition is ON ( ). To change the display from tripmeter or hourmeter to odometer, press and release the hourmeter/odometer/

(1) odometer

(1) (2)

(2) hourmeter/odometer/tripmeter select button

Tripmeter

ignition is ON ( ). To change the display from odometer or hourmeter to tripmeter, press and release the hourmeter/odometer/tripmeter select tripmeter select button and hold it in for at least 2 seconds.

(1) (2)

(1) tripmeter (2) hourmeter/odometer/tripmeter select button


21

０９／０５／１１１４：４４：５４３１ＨＰ４８３０００３１


Hourmeter

ignition is ON ( ). The hourmeter provides accurate service period information for initial and regular maintenance. To change the display from odometer or tripmeter to hourmeter, press and release the

(3)

(1)

(1) hourmeter


(2)

(3) hourmeter mark

22


０９／０５／１１１４：４５：０２３１ＨＰ４８３０００３２


Fuel Gauge

(Full), the fuel tank capacity including reserve is:

3.51 US gal (13.3 ) you should refill the tank as soon as possible. The amount of fuel left in the tank when the needle enters the red band is approximately:

0.77 US gal (2.9 )

(1)

(3) (2)

(1) fuel gauge

(2) gauge needle

(3) red band


23

０９／０５／１１１４：４５：１３３１ＨＰ４８３０００３３

Controls & Features

Fuel Valve

RIGHT SIDE

ON

(1)

OFF RES

(1) fuel valve tank.

The three-way fuel valve is used to control the flow of fuel from the fuel tank to the fuel pump unit.

ON − normal position for riding.

OFF − for parking, storing, or transportation.

RES

− for extra fuel to get to a gas supply for refueling.

Reserve Fuel

Remember to check that the fuel valve is in the ON position each time you refuel. If the fuel valve is left in the RES position, you may run out of fuel with no reserve.

For complete information about fueling your ATV, see page 102 .

24


０９／０５／１１１４：４５：２５３１ＨＰ４８３０００３４


Ignition Switch

(page 60 ). Insert the key and turn it to the right for the ON ( ) position.

The ignition switch is also used to reset the oil change indicator

(page 20 ).

Key Position

ON ( )

OFF ( )

Function

Electrical circuits on.

No electrical circuits function.

CENTER OF HANDLEBAR

ON

OFF

(1) ignition switch

(1)

ON

OFF


25

０９／０５／１１１４：４５：３５３１ＨＰ４８３０００３５


2WD/4WD Select Lever (Except TRX420TE )

permits a choice between the ‘‘2WD’’ and ‘‘4WD’’ drive modes. Select a drive mode that’s suitable for your riding.

Keep both hands on the handlebar while machine is in motion and come to a complete stop before using the 2WD/4WD select lever.

The 2WD/4WD select lever is located on the left side of the fuel tank.

To select the drive mode, shift the 2WD/4WD select lever to the desired position.

After using the 2WD/4WD select lever, the mode may not mechanically engage until forward motion begins.

2WD mode : the 4WD indicator goes off when the 2WD mode engages.

4WD mode : the 4WD indicator goes on when the 4WD mode engages.

(1)

4WD MODE

26

2WD MODE

(1) 2WD/4WD select lever


2WD MODE

(2)

4WD MODE

(2) 4WD indicator

０９／０５／１１１４：４５：４５３１ＨＰ４８３０００３６


Start Button

LEFT HANDLEBAR

(2)

(1) start button

(2) engine stop switch

(1)

START

OFF

RUN starts the engine. See

Starting Procedure,

page 61 .

When the start button is pushed, the starter motor will crank the engine.

The starter motor will not operate if the engine stop switch is in the OFF

( ) position when the start button is pushed.

Engine Stop Switch

To operate, slide the switch to the OFF ( ) position. The switch must be in the RUN ( ) position to start the engine, and it should normally remain in the RUN ( ) position even when the engine is OFF.

If your ATV is stopped with the ignition switch ON ( ) and the engine stop switch OFF ( ), the battery will discharge. Turn the ignition switch OFF ( ) to prevent battery discharge.


27

０９／０５／１１１４：４５：５３３１ＨＰ４８３０００３７


Headlight Switch

LEFT HANDLEBAR

(2)

(1)

(1) headlight switch

(2) headlight dimmer switch

ON

OFF

HI

LO

The headlight switch ( ) is used to turn the headlight ON ( ) or OFF

( ). To operate, turn the switch to ON ( ) or OFF ( ).

Headlight Dimmer Switch

and low beams of the headlight. To operate, turn the switch to HI ( ) for high beam, LO ( ) for low beam.

28


０９／０５／１１１４：４５：５９３１ＨＰ４８３０００３８


Throttle Lever

RIGHT HANDLEBAR

(A)

(1)

(1) throttle lever (A) to open the throttle

The throttle controls engine rpm (speed). To increase engine rpm, press pressure on the throttle lever. The throttle will automatically return to the closed position (engine idle) when you remove your thumb.


29

０９／０５／１１１４：４６：０６３１ＨＰ４８３０００３９


Gearshift Switch

These switches are used to select the next higher or lower gear in the gear.

See

Shif ting Gears,

page 65 .

LEFT HANDLEBAR

(1)

(2)

(1) upshift switch

(2) downshift switch

30


０９／０５／１１１４：４６：１３３１ＨＰ４８３０００４０


Reverse Selector Knob

stopped and the transmission in neutral (make sure the gear position indicator shows ‘‘N’’), push in the knob, squeeze the rear brake lever/

Riding in Reverse,

page 68 .

LEFT HANDLEBAR

(1)

(2)

(3)

(1) reverse selector knob

(2) rear brake lever/ parking brake lever



31

０９／０５／１１１４：４６：２１３１ＨＰ４８３０００４１


Front Brake Lever

The front brake lever is used to slow or stop your ATV. To operate, pull the lever. For information on braking techniques, see page 70 .

Rear Brake Lever/Parking Brake Lever

The rear brake lever/parking brake lever is used to slow or stop your

ATV. To operate, pull the lever. For information on braking techniques, see page 70 .

Rear Brake Pedal

The rear brake pedal is used to slow or stop your ATV. To operate, depress the pedal. For information on braking techniques, see page

70

.

32


０９／０５／１１１４：４６：２８３１ＨＰ４８３０００４２


Parking Brake

LEFT HANDLEBAR

(1)

(A)

(2)

(1) lock lever

(2) rear brake lever/parking brake lever

(A) to lock allows it to be used as a parking brake. To operate, first squeeze the rear brake lever/parking brake lever using your left hand and then lock it with the lock lever using your right hand. See

Parking

page 84 .

The brakelights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch OFF ( ) to avoid discharging the battery.


33

０９／０５／１１１４：４６：３４３１ＨＰ４８３０００４３


Flag Pole Bracket

RIGHT REAR

(1)

(1) flag pole bracket

Flag poles are optional equipment available from your Honda dealer. To the flag pole kit.

Flag poles are required in some riding areas. Check local regulations before riding.

34


０９／０５／１１１４：４６：４１３１ＨＰ４８３０００４４


Trailer Hitch

REAR

(2)

(1)

(1) trailer hitch (2) ball manufacturer.

To attach the ball and properly hook up a trailer, follow the trailer manufacturer’s instructions. For load limits and operational guidelines, see page 48 .


35

０９／０５／１１１４：４６：５１３１ＨＰ４８３０００４５


PS (Electric Power Steering) ( TRX420FPE only)

This ATV is equipped with an electronically controlled, electric-powerassisted steering system.

While the engine is running, the PS (Electric Power Steering) system provides power from the electric motor, which helps you to turn the

ATV’s handlebar more easily.

The PS system on this ATV utilizes an overheat protection feature to prevent damage to system components. In certain extended, repetitive high-load situations, the system will reduce or even disable power steering assist. The steering will perform as a normal non-PS system during this brief period. After cooling down, it will then return to normal PS operation.

The PS indicator should light when the ignition switch is turned ON

( ) and remain on until the engine is started.

The PS indicator also lights when there is any abnormality in the PS system. If this occurs, the electric power assist for turning will not be available, but the manual steering system will perform as usual.

If the PS indicator lights at any time while riding, reduce speed and take your ATV to a Honda dealer as soon as possible. Continuing to ride with a PS system problem can cause system damage.

Do not modify your Electric Power Steering system. In case of a malfunction, take your ATV to a Honda dealer.

36


０９／０５／１１１４：４７：０５３１ＨＰ４８３０００４６

Before Riding

Before each ride, you need to make sure you and your Honda are both ready to ride. To help get you prepared, this section discusses how to evaluate your riding readiness, what items you should check on your

ATV, and adjustments to make for your comfort, convenience, or safety.

This section also includes important information about loading.

Are You Ready to Ride?

.......................................................................

.

38

Protective Apparel .............................................................................

.

38

Rider Training ...................................................................................

.

40

Age Recommendation .......................................................................

.

41

No Passengers ...................................................................................

.

41

No Alcohol or Drugs .........................................................................

.

42

Is Your ATV Ready to Ride?

................................................................

.

43

Pre-ride Inspection ............................................................................

.

43

Load Limits & Guidelines .....................................................................

.

47

Loading .............................................................................................

.

47

Load Limits .......................................................................................

.

48

Loading Guidelines ...........................................................................

.

49

Accessories & Modifications ................................................................

.

50

Accessories ........................................................................................

.

50

Modifications ....................................................................................

.

51

Before Riding

37

０９／０５／１１１４：４７：１６３１ＨＰ４８３０００４７

Are You Ready to Ride?

Before you ride your ATV for the first time, we urge you to:

Read this owner’s manual and the labels on your ATV carefully.

Make sure you understand all the safety messages.

Know how to operate all the controls.

Before each ride, be sure:

You feel well and are in good physical and mental condition.

You are wearing an approved motorcycle helmet (with chin strap tightened securely), eye protection, and other protective clothing.

You don’t have any alcohol or drugs in your system.

Protective Apparel

For your safety, we strongly recommend that you always wear an approved motorcycle helmet, eye protection, boots, gloves, long pants, and a long-sleeved shirt or jacket whenever you ride.

Although complete protection is not possible, wearing proper gear can reduce the chance of injury when you ride.

Following are suggestions to help you choose the proper gear.

Helmet and Eye Protection

Your helmet is your most important piece of riding gear because it offers the best protection against head injuries. A helmet should fit your head comfortably and securely.

38

Before Riding

０９／０５／１１１４：４７：２５３１ＨＰ４８３０００４８


An open-face helmet offers some protection, but a full-face helmet offers more. Regardless of the style, look for a DOT (Department of

Transportation) sticker on any helmet you buy. Always wear a face shield or goggles to protect your eyes and help your vision.

Operating this ATV without wearing an approved motorcycle helmet, eye protection, and protective clothing could increase your chances of severe injury or death in the event of an accident.

Always wear an approved motorcycle helmet that fits properly and wear eye protection

(goggles or face shield), gloves, boots, long-sleeved shirt or jacket and long pants.

Additional Riding Gear

In addition to a helmet and eye protection, we also recommend:

Sturdy off-road motorcycle boots to help protect your feet, ankles, and lower legs.

Off-road motorcycle gloves to help protect your hands.

Riding pants with knee and hip pads, a riding jersey with padded elbows, and a chest/shoulder protector.

Before Riding

39

０９／０５／１１１４：４７：３１３１ＨＰ４８３０００４９


Rider Training

Developing your riding skills is an on-going process. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice riding the ATV in a safe area to build your skills. Do not ride in rough terrain until you get accustomed to the

ATV’s controls, and feel comfortable with its size and weight.

We urge all riders to take a ATV operator course approved by the ATV

Safety Institute (ASI). For information about the ASI training course nearest you, call the national toll-free number; (800) 887-2887.

Other riding tips can be found in the

Rider

Tips & Practice Guide f or the ATV

booklet that came with your ATV.

Operating this ATV without proper instruction could increase your risk of an accident which could lead to serious injury or death.

Beginning and inexperienced operators should complete the certified training course offered by

Honda. They should then regularly practice the skills learned in the course and the operating techniques described in the owner’s manual.

40

Before Riding

０９／０５／１１１４：４７：３９３１ＨＰ４８３０００５０


Age Recommendation

The minimum recommended age for this ATV model is 16. For safety, never let children under 16 years old operate this vehicle.

A child using an ATV that is not recommended for their age could lose vehicle control while riding, resulting in severe injury or death.

A child under 16 should never operate an ATV with engine size greater than 90cc.

No Passengers

This ATV is designed as an operator-only vehicle. The long seat is designed to allow the rider to change body position, not for carrying a passenger. Never let a passenger ride on the seat or on the front or rear cargo racks.

Carrying a passenger on this ATV greatly reduces your ability to balance and control this

ATV and could cause a crash and you or your passenger could be injured or killed.

Never carry a passenger on this ATV.

Before Riding

41

０９／０５／１１１４：４７：４４３１ＨＰ４８３０００５１


No Alcohol or Drugs

Alcohol, drugs and ATVs don’t mix. Even a small amount of alcohol can impair your ability to operate an ATV safely. Likewise, drugs − even if prescribed by a physician − can be dangerous while operating an

ATV. Consult your doctor to be sure it is safe to operate a vehicle after taking medication.

Operating this ATV after consuming alcohol or drugs can seriously affect your judgement, cause you to react more slowly, affect your balance and perception, and result in serious injury or death.

Never consume alcohol or drugs before or while operating this ATV.

42

Before Riding

０９／０５／１１１４：４７：５３３１ＨＰ４８３０００５２

Is Your ATV Ready to Ride?

Before each ride, it’s important to inspect your ATV and make sure any problem you find is corrected. A pre-ride inspection is a must, not only for safety, but because having a breakdown, or even a flat tire, can be a major inconvenience.

If your ATV has overturned or been involved in a collision, do not ride the vehicle until it has been inspected by your Honda dealer. There may be damage or other problems you cannot see.

Improperly maintaining this ATV or failing to correct a problem before riding can cause a crash in which you can be seriously hurt or killed.

Always perform a pre-ride inspection before every ride and correct any problems.

Pre-ride Inspection

Check the following items before you get on the ATV:

Engine Oil

Radiator

Coolant

Check the level and add oil if needed

(page 108 ).

Check for leaks.

Check the coolant level and add coolant if needed (page 119 ).

Check for leaks.

Before Riding

43

０９／０５／１１１４：４８：０８３１ＨＰ４８３０００５３


Fuel

Tires

Drivetrain Boots

Guards

Nuts & Bolts

Underbody &

Exhaust System

Air Cleaner Housing

Drain Tube

Leaks, Loose Parts

Check the level and add fuel (page 103 ) if needed. Also make sure the fuel fill cap is securely fastened.

Check for leaks.

Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damage or excessive wear (page 156 ).

Check for damage (pages ).

Check for damage or looseness

(pages ).

Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight.

Check for, and remove, any dirt, vegetation or other debris that could be a fire hazard or interfere with the proper operation of the vehicle.

Check for deposits in the drain tube. If necessary, clean the tube (page 129 ) and check the air cleaner housing.

Walk around your ATV and look for anything that appears unusual, such as a leak or loose cable.

44

Before Riding

０９／０５／１１１４：４８：２２３１ＨＰ４８３０００５４


Cable

Lights

Check the cable housings for wear. Check the fittings for looseness. Replace or tighten as needed.

Make sure the headlight, brakelight and taillight are working properly.

If you are carrying cargo, also check the following:

Loading Limits

Make sure you do not exceed the load limits

(page 48 ).

Cargo

Check that all cargo is secure.

Check these items after you get on the ATV:

Throttle

Check the freeplay and adjust if needed. Press the throttle to make sure it moves smoothly without sticking, and snaps shut automatically when it is released, in all steering positions

(page 130 ).

Brakes

Reverse Assist Lever

Squeeze the front and rear brake levers and step on the rear brake pedal to check that the controls operate normally. Check for proper freeplay (pages 146 , 148 ). Make sure there is no brake fluid leakage.

Check the freeplay and adjust if needed

(page 133 ). Make sure the lever operates smoothly without sticking.

Before Riding

45

０９／０５／１１１４：４８：３０３１ＨＰ４８３０００５５


Headlight and

Headlight Dimmer

Switch

Check for proper function (page 28 ).

Engine Stop Switch

Steering

Check for proper function (page 27 ).

Check that the wheels turn properly as you steer the handlebar. Move the handlebar right and left and check that there is no excessive backlash.

Remember, be sure to take care of any problem you find, or have your

Honda dealer correct it before you ride.

46

Before Riding

０９／０５／１１１４：４８：３８３１ＨＰ４８３０００５６

Load Limits & Guidelines

Your Honda was designed as a rider-only ATV. It was not designed to carry a passenger. It can carry cargo on the cargo racks, however, carrying cargo anywhere else or carrying a passenger could interfere with your balance and control of the ATV.

In addition, exceeding the weight limits or carrying an unbalanced load can seriously affect your ATV’s handling, braking and stability. Adding accessories or making modifications that change this ATV’s design and performance can also make it unsafe. Also, the weight of any accessories will reduce the maximum load the ATV can carry.

More specific information on load limits, accessories, and modifications follows.

Loading

How much weight you put on your ATV, and how you load it, are important to your safety. If you decide to carry cargo, you should be aware of the following information.

Overloading, improper loading, or carrying a passenger can cause a crash and you can be seriously hurt or killed.

Follow all load limits and other loading guidelines in this manual.

Before Riding

47

０９／０５／１１１４：４８：５２３１ＨＰ４８３０００５７


Load Limits

Following are the load limits for your ATV:

There are limits to how much weight can be carried on your ATV and be pulled in a trailer.

The following load limits apply to standard equipment only. Modifying your ATV, using non-standard equipment, or riding on terrain that is not flat and smooth could further reduce these limits.

maximum weight capacity

(includes the weight of the rider, all cargo, and accessories.)

485 lb (220 kg) front cargo rack weight limit rear cargo rack weight limit tow weight limit

(Combined weight of the trailer and all cargo in the trailer) tongue weight

(Weight on the trailer tongue) tongue and rear cargo weight

(Combined weight on the trailer tongue and on the rear cargo rack)

=

=

=

66 lb (30 kg)

133 lb (60 kg)

850 lb (385 kg)

=

=

30 lb (14 kg) recommended

133 lb (60 kg) maximum

Tongue weight can be measured with an ordinary bathroom scale. Place the scale under the tongue, using either a tongue jack or other support to keep the trailer level.

The weight of added accessories will reduce the maximum cargo weight you can carry.

48

Before Riding

０９／０５／１１１４：４９：０６３１ＨＰ４８３０００５８


Loading Guidelines

Carrying cargo or pulling a trailer will affect how your ATV handles and greatly reduce its ability in accelerating, braking and making turns and other maneuvers.

Be sure to observe the weight limits and follow these guidelines:

Check that the tires are properly inflated.

Do not place cargo anywhere on the ATV other than on the front and rear racks. Otherwise, operating stability may be adversely affected.

Never ride with a passenger on the front or rear cargo racks. The

ATV is not designed to carry a passenger.

Use the trailer hitch to tow another vehicle or trailer. Do not tow by tying a rope or cable to the rear rack.

Load cargo on the rear rack as far forward as possible. Make sure cargo on the front rack does not interfere with handlebar movement.

Do not allow cargo to extend beyond the edges of either the front or rear racks.

Make sure all cargo is secured before riding.

Balance cargo weight evenly on both sides.

Never exceed the maximum weight limit.

When towing a trailer, take care to maintain balance and stability.

Distribute cargo between the front and rear of the trailer to obtain the recommended tongue weight.

Allow extra room for starting, stopping and turning whenever you carry cargo or pull a trailer.

Avoid riding on steep slopes when carrying cargo or pulling a trailer.

Never cross a slope when towing a trailer.

Before Riding

49

０９／０５／１１１４：４９：１５３１ＨＰ４８３０００５９

Accessories & Modifications

Modifying your ATV or using non-Honda accessories can make your

ATV unsafe.

Before you consider making any modifications or adding an accessory, be sure to read the following information.

Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding accessories and modifications.

Accessories

We strongly recommend that you use only Honda Genuine Accessories that have been specifically designed and tested for your ATV. Because

Honda cannot test all other accessories, you must be personally responsible for proper selection, installation, and use of non-Honda accessories.

Check with your Honda dealer for assistance and always follow these guidelines:

50

Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls.

Make sure the accessory does not interfere with your ability to shift body position on the seat or operate hand and foot controls.

Do not add any electrical equipment that will exceed the vehicle’s electrical system capacity (page 213 ). A blown fuse can cause a loss of lights or engine power (page 198 ).

Before Riding

０９／０５／１１１４：４９：２１３１ＨＰ４８３０００６０

Accessories & Modifications

Modifications

We strongly advise you not to remove any original equipment or modify your ATV in any way that would change its design or operation. Such changes could seriously impair your ATV’s handling, stability, and braking, making it unsafe to ride.

We also advise you not to make any modifications or remove any equipment (such as the USDA qualified spark arrester or emission control system components) that would make your ATV illegal in your area.

Removing or modifying your lights, exhaust system, emission control system, or other equipment can also make your ATV illegal.

Before Riding

51

０９／０５／１１１４：４９：２４３１ＨＰ４８３０００６１

52

Before Riding

０９／０５／１１１４：４９：３９３１ＨＰ４８３０００６２

Basic Operation & Riding

This section gives basic riding instructions, including how to start and stop your engine, and how to use the throttle and brakes. It also provides important information on riding with cargo.

To protect your new engine and enjoy optimum performance and service life, refer to Break-in Guidelines (page 215 ).

Safe Riding Precautions ........................................................................

.

55

Off-road Use Only ............................................................................

.

55

Keep Hands and Feet on Controls .....................................................

.

56

Control Speed ....................................................................................

.

57

Use Care on Unfamiliar or Rough Terrain ........................................

.

58

Do Not Perform Stunts ......................................................................

.

59

Starting & Stopping the Engine

Preparation

............................................................

........................................................................................

.

.

60

60

Starting Procedure .............................................................................

.

61

Flooded Engine .................................................................................

.

62

Bank Angle Sensor Ignition Cut-off System ....................................

.

62

Stalled Engine ...................................................................................

.

63

How to Stop the Engine ....................................................................

.

64

Shifting Gears .......................................................................................

.

65

Riding in Reverse ..................................................................................

.

68

(cont’d)


53

０９／０５／１１１４：４９：４９３１ＨＰ４８３０００６３


Braking ..................................................................................................

.

70

Riding Your ATV .................................................................................

.

72

Making Turns ....................................................................................

.

72

Skidding or Sliding ...........................................................................

.

74

Riding Up Hills .................................................................................

.

75

Riding Down Hills ............................................................................

.

79

Crossing or Turning on Hills or Slopes .............................................

.

80

Riding Over Obstacles ......................................................................

.

82

Riding Through Water ......................................................................

.

83

Parking ..................................................................................................

.

84

54


０９／０５／１１１４：４９：５６３１ＨＰ４８３０００６４

Safe Riding Precautions

Before riding your ATV for the first time, please review the section beginning on page 1, and the

Bef ore Riding

ATV Saf ety

section beginning on page 37 .

Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.

Off-road Use Only

Your ATV and its tires are designed and manufactured for off-road use only, not for pavement. Riding on pavement can affect handling and control. You should not ride your ATV on pavement.

Operating this ATV on paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of control.

Never operate the ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets.

When riding off-road, also remember to always obey local off-road riding laws and regulations. Obtain permission to ride on private property. Avoid posted areas and obey ‘‘no trespassing’’ signs.


55

０９／０５／１１１４：５０：０３３１ＨＰ４８３０００６５


You should never ride your ATV on public streets, roads or highways, even if they are not paved. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. In many states it is illegal to operate ATVs on public streets, roads and highways.

Operating this ATV on public streets, roads or highways could cause you to collide with another vehicle.

Never operate this ATV on any public street, road or highway, even a dirt or gravel one.

Keep Hands and Feet on Controls

Always keep both hands on the handlebars and both feet on the footpegs when riding your ATV. This is important to maintain your balance and to control the vehicle. Removing even one hand from the handlebars or one foot from the footpegs can reduce your ability to control the ATV or could cause you to lose your balance and fall off the ATV.

Removing hands from handlebars or feet from footpegs during operation can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV.

Always keep both hands on the handlebars and both feet on the footpegs of your ATV during operation.

56


０９／０５／１１１４：５０：１０３１ＨＰ４８３０００６６


(1)

(1) footpeg

Control Speed

Riding at excessive speed increases the chance of an accident. In choosing a proper speed, you need to consider the capability of your vehicle, the terrain, visibility and other operating conditions, plus your own skills and experience.

Operating this ATV at excessive speeds increases your chances of losing control of the

ATV, which can result in an accident.

Always go at a speed that is proper for your vehicle, the terrain, visibility and other operating conditions, and your experience.


57

０９／０５／１１１４：５０：１５３１ＨＰ４８３０００６７


Use Care on Unfamiliar or Rough Terrain

Before riding in a new area, always check the terrain thoroughly. Don’t ride fast on unfamiliar terrain or when visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or holes in time to react.)

Failure to use extra care when operating this

ATV on unfamiliar terrain could result in the ATV overturning or going out of control.

Go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating the

ATV.

58


０９／０５／１１１４：５０：２３３１ＨＰ４８３０００６８


Never ride past the limit of visibility. Maintain a safe distance between your ATV and other off-road vehicles. Always exercise caution, and use extra care on rough, slippery and loose terrain.

Failure to use extra care when operating on excessively rough, slippery or loose terrain could cause loss of traction or vehicle control, which could result in an accident, including an overturn.

Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control the ATV on such terrain. Always be especially cautious on these kinds of terrain.

Do Not Perform Stunts

You should always operate your ATV in a safe and reasonable manner.

When riding, always keep all four wheels on the ground.

Attempting wheelies, jumps, and other stunts increases the chance of an accident, including an overturn.

Never attempt stunts, such as wheelies or jumps. Don’t try to show off.


59

０９／０５／１１１４：５０：３４３１ＨＰ４８３０００６９

Starting & Stopping the Engine

Always follow the proper starting procedure described below.

For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your ATV’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death.

Preparation

(1) (2)

(3)

(1) fuel valve

(2) ignition switch

(4)

(3) neutral indicator

(4) engine stop switch

1.

2.

Before starting, select a level surface and lock the parking brake

(page 33 ).

2 ).

Confirm the following:

60

The engine stop switch ( ) is set to RUN ( ).


０９／０５／１１１４：５０：４１３１ＨＰ４８３０００７０


Starting Procedure

This vehicle has a fuel-injected engine with an automatic choke.

Follow the procedure indicated below.

Any Air Temperature

Press the start button with the throttle completely closed.

The engine will not start if the throttle is fully open (because the electronic control module cuts off the fuel supply).


61

０９／０５／１１１４：５０：５２３１ＨＰ４８３０００７１


Flooded Engine

If the engine fails to start after repeated attempts, it may be flooded with excess fuel. To clear a flooded engine:

1.

2.

3.

4.

Leave the engine stop switch set to RUN ( ).

Open the throttle fully.

Press the start button for 5 seconds.

Follow the normal starting procedure.

5.

If the engine starts, then open the throttle slightly if idling is unstable.

If the engine does not start, wait 10 seconds, then follow steps

1

−

4 again.

If the engine still won’t start, refer to

Start,

page 186 .

If Your Engine Quits or Won’t

Bank Angle Sensor Ignition Cut-off System

Your vehicle’s banking (lean angle) sensor system is designed to automatically stop the engine if the vehicle is overturned.

Before restarting the engine, you must turn the ignition switch to the

OFF ( ) position and then back to ON ( ). The engine will not restart until you perform this procedure.

62


０９／０５／１１１４：５０：５７３１ＨＰ４８３０００７２


Stalled Engine

You can restart the engine while the vehicle is stopped by squeezing the front brake lever and pressing the start button.

Do not press the throttle lever while starting in gear. Your ATV is equipped with a start inhibitor system that will cut off the ignition if the throttle is open while attempting to start in gear.

Once you have started the engine, release the front brake lever, then apply throttle gradually.


63

０９／０５／１１１４：５１：０５３１ＨＰ４８３０００７３


How to Stop the Engine

Normal Engine Stop

To stop the engine, make sure the transmission is in neutral by checking that the neutral indicator light is on, then turn the ignition switch OFF

( ).

The engine stop switch should normally remain in the RUN ( ) position even when the engine is OFF.

If your ATV is stopped with the engine stop switch OFF ( ) and the ignition switch ON ( ), the battery will discharge.

Emergency Engine Stop

To stop the engine in an emergency, use the engine stop switch. To operate, slide the switch to either OFF ( ) position.

64


０９／０５／１１１４：５１：１８３１ＨＰ４８３０００７４

UPSHIFTING SEQUENCE

Shifting Gears

(1)

(A)

DOWNSHIFTING SEQUENCE

(2)

(A)

(1) upshift switch


(A) press

Your ATV has five forward gears: 1, 2, 3, 4, and 5.

Two gearshift switches are located next to the left handlebar grip: upshift ( ) and downshift ( ).

To select reverse, use the reverse selector knob (page 68 ).

After starting the engine and letting it warm up, follow these procedures:

1.

With the transmission in neutral, release the parking brake, but continue squeezing the rear brake lever.

2.

With the throttle closed, press the upshift switch once to shift into 1st

(first) gear.

(cont’d)


65

０９／０５／１１１４：５１：２８３１ＨＰ４８３０００７５

Shifting Gears

3.

Release the rear brake lever and increase engine speed by gradually opening the throttle.

4.

When speed increases, release the throttle and shift to 2nd gear by pressing the upshift switch once.

5.

Repeat this sequence to progressively upshift to 3rd, 4th and 5th (top) gear.

6.

To downshift, press the downshift switch once. Remember to close the throttle each time you shift to the next lower gear.

The transmission cannot be upshifted from neutral to 1st gear when the engine speed is above 3,000 rpm or the ground speed is above 2 mph

(3 km/h).

The transmission cannot be downshifted from 1st gear to neutral when the ground speed is above 2 mph (3 km/h).

If the electric shift system malfunctions, the transmission cannot be shifted by pressing the gearshift switches. See your Honda dealer. (In an emergency, a gear may be selected manually so you may move the vehicle. See

Emergency Gear Selection & Operation,

page 188 ).

Learning when to shift gears comes with experience. Keep the following tips in mind:

As a general rule, shift while moving in a straight line.

Close the throttle completely before shifting. Improper shifting may damage the engine, transmission, and drivetrain.

Upshift to a higher gear or reduce throttle before engine rpm (speed) gets too high. Learn the relationship between engine sound and the normal shifting points.

66


０９／０５／１１１４：５１：３５３１ＨＰ４８３０００７６

Shifting Gears

Downshift to a lower gear before you feel the engine laboring

(lugging) at low rpm.

Avoid downshifting to help slow your ATV when engine rpm is high.

Downshifting when engine speed is near its allowable maximum may over-rev the engine and possibly cause damage.

To prevent transmission damage, do not coast or tow the ATV for long distances with the engine off.

Recommended Shift Points

Ride in the highest gear that lets the engine run and accelerate smoothly.

This will give you good fuel economy and effective emissions control.


67

０９／０５／１１１４：５１：４４３１ＨＰ４８３０００７７

Riding in Reverse

If you need to ride in reverse, make sure the area behind you is clear and only operate the ATV at low speed.

Improperly operating in reverse could cause you to hit an obstacle or person behind you, resulting in serious injury.

Make sure there are no obstacles or people behind you before selecting reverse gear. When it is safe to proceed, go slowly.

1.

Bring the vehicle to a complete stop, then make sure the transmission is in neutral.

2.

Be sure there are no obstacles or people in the way.

3.

once to shift into ‘‘R’’ (reverse) gear.

LEFT HANDLEBAR

(1)

(2)

(4)

(3)

68

(1) reverse selector knob

(2) rear brake lever/ parking brake lever



(4) upshift switch

０９／０５／１１１４：５１：５１３１ＨＰ４８３０００７８

Riding in Reverse

Your ATV may be equipped with a reverse speed limiter, which helps the vehicle to maintain a saf e speed while riding in reverse gear.

4.

5.

Release the rear brake lever/parking brake lever.

Open the throttle gradually and ride slowly. Do not open the throttle

6.

suddenly or make abrupt turns.

To stop, close the throttle and gradually apply both the front and rear brakes. Do not abruptly apply the rear brake by itself.

7.

once to shift into ‘‘N’’ (neutral) gear.

The transmission cannot be shifted from neutral back into reverse when the engine speed is above 3,000 rpm or speed of your ATV is above 2 mph (3 km/h).

Applying only the rear brake abruptly when operating in reverse gear could cause the front wheels to lift off the ground and the ATV could overturn backwards.

Carefully apply both the front and rear brakes when stopping in reverse gear.


69

０９／０５／１１１４：５２：００３１ＨＰ４８３０００７９

Braking

Your ATV is equipped with disc brakes on both front wheels which are hydraulically activated by operating the right brake lever. A single drum brake on the rear axle housing is mechanically activated by depressing the brake pedal or operating the left brake lever.

Except TRX420TE:

Although the front and rear brakes have separate controls, all four wheels are interconnected when your ATV is in the 4WD mode. So operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.

As a general rule, the front braking system provides about 70 percent of total stopping power.

For full braking effectiveness, use both the pedal and lever simultaneously. Using both braking systems will stop your ATV faster with greater stability.

To slow or stop, apply the brake lever and brake pedal smoothly, while downshifting to match your speed.

Gradually increase braking as you feel the brakes slowing your speed.

The increase in engine compression from downshifting will help slow your ATV.

Applying the brakes too hard may cause the wheels to lock and slide, reducing control of your ATV. If this happens, release the brake controls, steer straight ahead until you regain control, then reapply the brakes more gently.

When possible, reduce your speed or complete braking before entering a turn. Avoid braking or closing the throttle quickly while turning. Either action may cause one or more wheels to slip and reduce your control of your ATV.

70


０９／０５／１１１４：５２：０７３１ＨＰ４８３０００８０

Braking

Your ability to brake in a turn and to brake hard in an emergency situation are important riding skills.

When descending a long, steep grade, use engine compression braking by downshifting, with intermittent use of both brakes. Continuous brake application can overheat the brakes and reduce their effectiveness.

Riding with your foot resting on the brake pedal or your hands on the brake levers may overheat the brakes, reducing effectiveness.

For information on how to apply the brakes in various riding situations, see the following section,

Riding Your ATV

.


71

０９／０５／１１１４：５２：１２３１ＨＰ４８３０００８１

Riding Your ATV

Making Turns

Learn how to turn your ATV properly. Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns.

Turning improperly can make the ATV go out of control, causing a collision or overturn.

Always follow proper procedures for turning as described in this owner’s manual.

Practice turning at low speeds before attempting to turn at faster speeds.

Do not turn at excessive speeds.

72


０９／０５／１１１４：５２：１９３１ＨＰ４８３０００８２

Riding Your ATV

Lean your body to the inside of a turn and forward.

To make a turn on level ground: Steer the handlebar and lean your body toward the inside of the turn. Leaning helps balance the vehicle, and it feels more comfortable. Leaning into a turn is an important technique to master in riding an ATV.

To make a sharp turn at low speed: It helps to shift your body slightly forward on the seat, and lean inside, as you steer the handlebar. Shifting weight forward allows the rear wheels to turn easier, and it also improves front-wheel steering.

To make a turn from a full stop: Apply the throttle gradually when you turn and start up at the same time. Remember to shift your body forward to make sharp low-speed turns and whenever you turn while accelerating from a full stop.


73

０９／０５／１１１４：５２：２５３１ＨＰ４８３０００８３

Riding Your ATV

Skidding or Sliding

The terrain surface can be a major factor affecting turns. Skidding during a turn is more likely to occur on slippery surfaces, such as snow, ice, mud and loose gravel. If you skid on ice, you may lose all directional control. To avoid skidding on slippery terrain, keep your speed low and ride with caution.

Skidding or sliding improperly may cause you to lose control of this ATV. You may also regain traction unexpectedly, which may cause the

ATV to overturn.

Learn to safely control skidding by practicing at low speeds and on level, smooth terrain.

If your ATV skids sideways during a turn, steer in the direction of the skid. Avoid hard braking or accelerating until you have regained directional control.

74


０９／０５／１１１４：５２：３２３１ＨＰ４８３０００８４

Riding Your ATV

Riding Up Hills

The ATV’s ability to safely climb hills largely depends on the rider’s skill and judgment. Begin by practicing on smooth, gentle slopes. As you gain experience, you’ll learn the hazards and your own limitations.

You may then proceed to ride on more difficult terrain. However, you must be able to decide which hills or hazards might cause the ATV to overturn. Avoid excessively steep hills.

Operating on excessively steep hills can cause the vehicle to overturn more easily than operating on level surfaces or small hills.

Never operate the ATV on hills too steep for the

ATV or for your abilities.

When climbing hills, you must shift weight toward the front wheels to help keep them on the ground. To do this, shift your body slightly forward on the seat and lean forward. For greater weight shift, move your body farther forward and lean forward.

Climbing hills improperly could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for climbing hills as described in this owner’s manual.


75

０９／０５／１１１４：５２：４０３１ＨＰ４８３０００８５

Riding Your ATV

Shift weight forward when climbing hills.

Always check the terrain carefully before you start up any hill.

Never climb hills with excessively slippery or loose surfaces.

To climb a hill, take a running start in an appropriate gear and speed for the conditions. Maintain a steady speed as you ascend the hill.

Never open the throttle suddenly or make sudden gear changes. The

ATV could flip over backward.

Never go over the top of any hill at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill.

76


０９／０５／１１１４：５２：５２３１ＨＰ４８３０００８６

Riding Your ATV

Stalling the ATV and/or Rolling Backwards:

If you incorrectly estimate climbing capability or terrain conditions, the

ATV may not have enough power or traction to continue uphill. If this happens, the ATV can stall and/or roll backwards.

Stalling, rolling backwards or improperly dismounting while climbing a hill could result in the ATV overturning.

Always follow proper procedures for climbing a hill as described in this owner’s manual.

What to do if the ATV stalls or rolls backwards when climbing a hill:

If you are about to lose all forward speed:

1.

Using the front and rear brakes together, bring the ATV to a stop with the vehicle pointed straight uphill.

2.

3.

Get off the ATV while you continue holding the brakes.

Shift into neutral, set the parking brake and turn the engine off.

4.

Then assess the situation.

If the ATV starts rolling backwards before you begin braking:

1.

2.

Keep your weight uphill.

Carefully apply the front brakes first, then carefully apply the rear brake. Do not apply either brake abruptly if you are rolling backwards, or the vehicle may overturn.

If the ATV continues sliding backwards:

After you’ve applied the brakes, get off and away from the vehicle.

Except TRX420TE:

Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.


77

０９／０５／１１１４：５３：０２３１ＨＰ４８３０００８７

Riding Your ATV

What to do after the ATV has stalled or rolled backwards:

If the hill is too steep or too slippery, or if you have any doubt whether you can safely walk the ATV back down the hill, leave the vehicle where it is and get help. If possible, block the wheels so the vehicle doesn’t roll backwards.

If the hill is not too steep and you have good footing, you may be able to walk the ATV back down the hill. Make sure your intended path is clear in case you lose control of the ATV.

Be sure your legs are clear of the wheels.

Body position for backing down a hill.

1.

Stand with your body facing downhill, beside the vehicle so you can reach the rear brake lever with your right hand.

2.

Be sure your legs are clear of the wheels.

Check your footing.

3.

Slowly and carefully back the ATV down the hill using the rear brake lever to control speed.

4.

If you lose control of the ATV, for your safety, get away from the vehicle.

78


０９／０５／１１１４：５３：０９３１ＨＰ４８３０００８８

Riding Your ATV

Riding Down Hills

It’s usually advisable to descend hills with the ATV pointed straight downhill. Avoid angles that would cause the vehicle to lean sharply to one side.

Going down a hill improperly could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for going down hills as described in this owner’s manual.

On downhills, shift your weight back.

As you approach a downhill, stop and survey the terrain below. Never ride past the limit of your visibility. Never go down a hill at high speed.


79

０９／０５／１１１４：５３：１８３１ＨＰ４８３０００８９

Riding Your ATV

When you’ve selected a safe downhill path, shift into a lower gear, shift your weight back with your arms extended and braced against the handlebar, then go down slowly with the throttle closed.

Use mainly the rear brake to control speed. Avoid using either the front brake or rear brake hard or abruptly when riding down hills.

Except TRX420TE:

Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels.

Remember, braking effectiveness is reduced on any hill with a loose surface.

Crossing or Turning on Hills or Slopes

Riding on hills or slopes is different from riding on level terrain. Be careful when riding on any hill. Make sure that you practice on gentle, smooth slopes before attempting to ride on steeper or more difficult terrain.

Improperly crossing hills or turning on hills could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for crossing or turning on slopes as described in this owner’s manual. Avoid crossing steep hills if possible.

80


０９／０５／１１１４：５３：２６３１ＨＰ４８３０００９０

Riding Your ATV

Crossing Hills or Slopes

To maintain balance and stability when riding across a slope, you need to shift weight toward the uphill side of the vehicle. To do this, move your body off the center of the seat and lean toward the uphill side.

On a slippery or loose surface, you may also need to steer slightly uphill to maintain a straight course across the slope.

Avoid crossing hills that are excessively steep, slippery or rough.

Shift weight uphill when crossing slopes.

Making Turns on Slopes

Compared to riding on level ground, you may need to shift more weight and lean more when making turns on slopes.

Do not make turns on any slopes until you have first mastered the techniques for making turns on level terrain.


81

０９／０５／１１１４：５３：３２３１ＨＰ４８３０００９１

Riding Your ATV

Riding Over Obstacles

Before operating in a new area, check for obstacles. Watch out for bumps, rain ruts, potholes and other obstacles in the terrain. When you approach any obstacle, reduce your speed and be prepared to stop.

Never try to ride over large obstacles, such as large rocks or fallen logs.

Improperly operating over obstacles could cause loss of control or a collision and could cause the ATV to overturn.

When you go over obstacles, always follow proper procedures as described in this owner’s manual.

82


０９／０５／１１１４：５３：４２３１ＨＰ４８３０００９２

Riding Your ATV

Riding Through Water

Your ATV is designed to travel through water up to approximately

10 inches (254 mm) deep. Before crossing a stream, make sure the water is not too deep or flowing too fast.

The ATV tires have some ability to float.

Operating this ATV through deep or fast-flowing water may cause a loss of traction and loss of control, which could lead to an accident.

Never operate this ATV in fast-flowing water or in water deeper than that specified in this owner’s manual.

1.

Choose a path where both banks have gradual slopes.

2.

3.

Proceed through the water at a slow, steady speed.

Watch out for submerged obstacles and slippery rocks.

4.

5.

Avoid getting the spark plug or air cleaner wet, as this would cause the engine to stop.

After leaving the water, always test both the front and rear brakes.

Riding through water can make the brakes less effective than normal, and may reduce stopping ability.

If necessary, apply the brakes repeatedly until they dry out and operate normally.

If the brakes don’t regain effectiveness, stop your ATV and follow the procedures on page 152 .


83

０９／０５／１１１４：５３：５７３１ＨＰ４８３０００９３

Parking

1.

2.

Look for level parking area. Make sure the ground surface is firm.

After bringing your ATV to a stop, hold the brakes while you shift into neutral.

Set the parking brake.

3.

4.

5.

Turn the ignition switch OFF ( ).

If you’re finished riding for the day, turn the fuel valve OFF.

If it is necessary to start the engine when your ATV in gear and is stopped on a grade, rock the vehicle back and forth to allow shifting the transmission into neutral.

The brakelights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch OFF ( ) to avoid discharging the battery.

Parking on a Steep Incline or a Loose or Slippery Surface

If you must park your ATV on a steep incline or loose or slippery surface, use the following procedure:

1.

2.

While holding the brakes, set the parking brake.

Turn the ignition switch OFF ( ) and release the brakes.

3.

If the ATV begins to move, either while sitting on it or after you dismount, find a better parking location.

4.

If rocks or other objects are available, you can block the wheels as shown for additional security.

84


０９／０５／１１１４：５４：１２３１ＨＰ４８３０００９４

Servicing Your Honda

To help keep your ATV in good shape, this section includes a

Maintenance Schedule for required service and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on fuels and oils, and tips for keeping your

Honda looking good.

For information about replacing fuses, see page 198 .

For information about the exhaust emission and noise requirements of the U.S. Environmental Protection Agency (EPA) and the California Air

Resources Board (CARB), see page 216 .

Maintenance, replacement or repair of the emission control devices and systems may be performed by any ATV repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

Bef ore You Service Your Honda

The Importance of Maintenance ...........................................................

.

87

Maintenance Safety ...............................................................................

.

88

Important Safety Precautions ............................................................

.

89

Maintenance Schedule ..........................................................................

.

90

Maintenance Record ..............................................................................

.

94

Service Preparations

Maintenance Component Locations ......................................................

.

95

Tool Kit .................................................................................................

.

98

Owner’s Manual Storage .......................................................................

.

99

Seat Removal

Clip Removal

....................................................................................

.

....................................................................................

.

100

101

(cont’d)


85

０９／０５／１１１４：５４：３１３１ＨＰ４８３０００９５


Service Procedures

Fluids & Filters

Fuel ...................................................................................................

.

Engine Oil & Filter ............................................................................

.

Gear Case Oil ....................................................................................

.

Differential Oil (Except TRX420TE ) ............................................

.

Coolant ..............................................................................................

.

Air Cleaner ........................................................................................

.

102

105

114

116

118

124

Engine

Throttle ..............................................................................................

.

Clutch System ...................................................................................

.

Reverse Lock System ........................................................................

.

Spark Plug .........................................................................................

.

Valves ................................................................................................

.

Spark Arrester ...................................................................................

.

130

132

133

134

137

138

Chassis

Suspension ........................................................................................

.

Brakes ................................................................................................

.

Tires ..................................................................................................

.

Guards ...............................................................................................

.

Drivetrain Boots ................................................................................

.

139

142

153

160

162

Electrical

Battery ...............................................................................................

.

164

Appearance Care ...............................................................................

.

169

86


０９／０５／１１１４：５４：３９３１ＨＰ４８３０００９６

The Importance of Maintenance

A well-maintained ATV is essential for safe, economical, and troublefree riding. It will also help reduce air pollution. Careful pre-ride inspections and good maintenance are especially important because your

ATV is designed to be ridden over rough off-road terrain.

To help you properly care for your ATV, this section of the manual provides a Maintenance Schedule. The service intervals in this schedule are based on average riding conditions.

Improperly maintaining this ATV or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed.

Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

Frequent servicing of the air cleaner is especially important to help you avoid a possible costly engine repair.

If your ATV overturns or is involved in a crash, be sure your Honda dealer inspects all major parts, even if you are able to make some repairs.


87

０９／０５／１１１４：５４：４５３１ＨＰ４８３０００９７

Maintenance Safety

This section includes instructions on how to perform some important maintenance tasks. If you have basic mechanical skills, you can perform many of these tasks with the tools provided with your ATV.

Other tasks that are more difficult and require special tools are best performed by professionals. Removing the wheels should normally be handled only by a Honda technician or other qualified mechanic.

Instructions are included in this manual only to assist in emergency service.

Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner’s manual.

88


０９／０５／１１１４：５４：５１３１ＨＰ４８３０００９８

Maintenance Safety

Important Safety Precautions

Make sure the engine is off before you begin any maintenance or repairs. This will help eliminate several potential hazards:

Carbon monoxide poisoning from engine exhaust.

Be sure there is adequate ventilation whenever you operate the engine.

Burns from hot ATV parts.

Let the engine and exhaust system cool before touching.

Injury from moving parts.

Do not run the engine unless instructed to do so.

Read the instructions before you begin, and make sure you have the tools and skills required.

To reduce the possibility of a fire or explosion, be careful when working around gasoline. Use only non-flammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts.

Remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new Honda Genuine Parts or other equivalents for repair and replacement. If you have the tools and skills required for additional maintenance jobs, you can purchase an official Honda

Service Manual (page 224 ).


89

０９／０５／１１１４：５４：５８３１ＨＰ４８３０００９９

Maintenance Schedule

The required Maintenance Schedule that follows specifies how often you should have your ATV serviced, and what things need attention. It is essential to have your ATV serviced as scheduled to maintain safe, dependable performance and proper emission control.

The service intervals in this Maintenance Schedule are based on average riding conditions. Some items will need more frequent service if you ride in unusually wet or dusty areas or at full throttle. Consult your

Honda dealer for recommendations applicable to your individual needs and use.

Some items in the Maintenance Schedule can be performed with basic mechanical skills and hand tools. Procedures for these items are provided in this manual. Other items involve more extensive procedures and may require special training, tools, and equipment. We recommend that you have your Honda dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment.

Procedures for such items in this schedule are provided in an official

Honda Service Manual available for purchase (page 224 ).

If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. If you decide to do your own maintenance, use only Honda Genuine Parts or their equivalents for repair or replacement to ensure the best quality and reliability.

90


０９／０５／１１１４：５５：０８３１ＨＰ４８３００１００


Perform the pre-ride inspection (page 43 ) and owner maintenance on this section at each scheduled maintenance period.

Each item on the maintenance schedule requires some mechanical knowledge. Certain items (particularly those marked

＊ and

＊＊

) may require more technical information and tools. Consult your Honda dealer.

＊

＊＊

Should be serviced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Service Manual (page 224 ).

In the interest of safety, we recommend these items be serviced only by your Honda dealer.

Summary of Maintenance Schedule Notes & Procedures:

NOTES:

1.

2.

Service more frequently when riding in dusty areas, sand or snow.

Service more frequently after riding in very wet or muddy conditions.

3.

Replace every 2 years. Replacement requires mechanical skill.


91

０９／０５／１１１４：５５：１９３１ＨＰ４８３００１０１


Maintenance Procedures:

I: inspect and clean, adjust, lubricate, or replace, if necessary

C: clean

A: adjust

L: lubricate

R: replace

ITEMS

FUEL LINE

THROTTLE OPERATION

AIR CLEANER

AIR CLEANER HOUSING

DRAIN TUBE

SPARK PLUG

VALVE CLEARANCE

ENGINE OIL

FREQUENCY

ENGINE OIL FILTER

RADIATOR COOLANT

COOLING SYSTEM

WHICHEVER

COMES

FIRST mi km

NOTE

MONTH

HOURS

NOTE 1

NOTE 2

NOTE 3

NOTE 2

INITIAL

MAINT.

100

150

1

20

REGULAR

MAINT. INTERVAL

600

1000

6

100

C

I

1200

2000

12

200

C

I

I

I

I

INITIAL=

I

I

100 mi (150 km),

20 operating hours

I

I or 1 month: R

REGULAR=

Every 600 mi

(1,000 km),

100 operating hours or 12 months: R

I

I I

I

Refer to page

110

118

−


−

130

124

129

134

137

105

92


０９／０５／１１１４：５５：３０３１ＨＰ４８３００１０２


ITEMS

FREQUENCY

WHICHEVER

COMES

FIRST mi km

NOTE

MONTH

HOURS

DRIVETRAIN BOOTS

REAR FINAL GEAR CASE

OIL AND DIFFERENTIAL

OIL (Except TRX420TE)

REAR FINAL GEAR CASE

OIL (TRX420TE only)

2WD/4WD SELECT

SYSTEM

(Except TRX420TE)

BRAKE FLUID

BRAKE SHOES WEAR

BRAKE PADS WEAR

BRAKELIGHT SWITCH

BRAKE SYSTEM

REVERSE LOCK SYSTEM

GUARDS

CLUTCH SYSTEM

SUSPENSION

SPARK ARRESTER

NUTS, BOLTS,

FASTENERS

WHEELS/TIRES

TIE-ROD AND JOINT

BOOTS

STEERING SHAFT

HOLDER BEARINGS

STEERING SYSTEM

NOTE 3

NOTE 1,2

NOTE 1,2

INITIAL

MAINT.

100

150

1

20

REGULAR

MAINT. INTERVAL

600

1000

6

100

I

(R:EVERY

1200

2000

12

200

I

I

2 YEARS)

I

I

I

I

I

I

I

(R:EVERY

2 YEARS)

I

I

I

I

I

I

I

C

I

I

I

I

I

I

I

I

I

C

I

I

I

I

I

I

I

I

I

Refer to page

162

114,

116

114

−

−

−


In the interest of safety, we recommend these items be serviced only by your Honda dealer.

160

132

−

138

−

142

150

145

151

142

133

−

−


93

０９／０５／１１１４：５５：３７３１ＨＰ４８３００１０３

Maintenance Record

Keeping an accurate maintenance record will help ensure that your ATV is properly maintained. Retain detailed receipts to verify the maintenance was performed. If the ATV is sold, these receipts should be transferred with the ATV to the new owner. Make sure whoever performs the maintenance completes this record. All scheduled maintenance, including the 100 mile (150 km) or 1 month or 20 hours initial maintenance, is considered a normal owner operating cost and will be charged for by your dealer. Use the space under Notes to record anything you want to remind yourself about or mention to your dealer.

ODO or

HOUR

Date Performed

By:

Notes

Miles (km) or months or hours

100 (150) or

1 or 20

600 (1,000) or

6 or 100

1,200 (2,000) or

12 or 200

1,800 (3,000) or

18 or 300

2,400 (4,000) or

24 or 400

3,000 (5,000) or

30 or 500

3,600 (6,000) or

36 or 600

4,200 (7,000) or

42 or 700

4,800 (8,000) or

48 or 800

94


０９／０５／１１１４：５５：４２３１ＨＰ４８３００１０４

Maintenance Component Locations

rear brake lever/ parking brake lever front brake fluid reservoir front brake lever fuel fill cap throttle lever


95

０９／０５／１１１４：５５：４８３１ＨＰ４８３００１０５


coolant reserve tank air cleaner front suspension spring pre-load adjuster

(Except TRX420TE) air cleaner housing drain tube rear brakelight switch engine oil filter front brake caliper rear brake pedal differential oil filler cap (Except TRX420TE) differential oil drain bolt (Except TRX420TE)

96


０９／０５／１１１４：５５：５５３１ＨＰ４８３００１０６


clutch spark plug owner’s manual air pressure gauge gear change tool battery fuse box main fuse

PS fuse (TRX420FPE only) tool kit engine oil filler cap/dipstick spark arrester engine oil drain bolt gear case oil filler cap gear case oil drain bolt rear suspension spring pre-load adjuster

(Except TRX420TE)


97

０９／０５／１１１４：５６：０３３１ＨＰ４８３００１０７

Tool Kit

cargo rack.

An optional, larger tool kit may be available. Check with your Honda dealer’s parts department.

REAR SEAT UNDERSIDE

(2)

(1)

(3)

(1) tool kit

(2) storage compartment

(4)

(3) rubber strap

(4) gear change tool

98


０９／０５／１１１４：５６：１２３１ＨＰ４８３００１０８

Owner’s Manual Storage

Your ATV provides storage for the owner’s manual so you’ll have it

To remove the seat, see page 100 .

Be careful not to flood this area when washing your ATV.

SEAT UNDERSIDE

(1)

(4)

(1) owner’s manual

(2) seat

(2)

(3)

(3) air pressure gauge

(4) plastic document bag


99

０９／０５／１１１４：５６：２４３１ＨＰ４８３００１０９

Seat Removal

Refer to

Saf ety Precautions

on page 89 .

The seat must be removed for the air cleaner, engine oil, engine oil filter, clutch, spark plug, battery and fuse maintenance and to remove the side covers, rear fender cover and left tank side cover, to access the owner’s manual, air pressure gauge, gear change tool, coolant reserve tank cap and color label.

(3) (2) (5)

(4) (6)

Removal

1.

2.

(1) seat latch

(2) seat

(3) front prongs

Installation

1.

2.

Press down on the seat until locks.

100


(4) hooks

(5) studs

(6) grommets

(1)

０９／０５／１１１４：５６：３２３１ＨＰ４８３００１１０

Clip Removal

Removal

1.

Press down on the center pin to release the lock.

2.

Pull the clip out of the hole.

1.

2.

Installation

1.

Push the bottom of the pin.

2.

3.

Insert the clip into the hole.

Lightly press down on the center pin to lock the clip.

1.

2.

3.


101

０９／０５／１１１４：５６：４２３１ＨＰ４８３００１１１

Fuel

Refer to


on page 89 .

Fuel Recommendation

type pump octane number unleaded

86 (or higher)

Use only unleaded fuel in your Honda. If you ride your Honda in a country where leaded fuel might be available, take precautions to use only unleaded fuel.

Your engine is designed to use any unleaded gasoline that has a pump octane number of 86 or higher. Gasoline pumps at service stations normally display the pump octane number. For information on the use of oxygenated fuels, see page 220 .

Use of lower octane gasoline can cause persistent ‘‘pinging’’ or ‘‘spark knock’’ (a loud rapping noise) which, if severe, can lead to engine damage. Light pinging experienced while operating under a heavy load, such as climbing a hill, is no cause for concern.

If pinging or spark knock occurs at a steady engine speed under normal load, change brands of gasoline. If pinging or spark knock persists, consult your Honda dealer.

Never use stale or contaminated gasoline or an oil/gasoline mixture.

Avoid getting dirt, dust, or water in the fuel tank.

102


０９／０５／１１１４：５６：５４３１ＨＰ４８３００１１２

Fuel

Fuel Capacity

Fuel tank capacity, including reserve:

3.51 US gal (13.3 )

Reserve capacity:

0.69 US gal (2.6 )

The tank should be refilled as soon as possible after switching to reserve, and the fuel valve should be returned to the ON position after refueling to avoid running out of fuel with no reserve.

Refueling Procedure

Refer to


on page 89 .

(4)

(3) (2)

(1)

(1) fuel fill cap

(2) breather tube

(3) handlebar cover hole

(4) filler neck


103

０９／０５／１１１４：５７：０３３１ＨＰ４８３００１１３

Fuel

1.

2.

3.

Avoid over filling the tank. There should be no fuel in the filler neck.

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when handling fuel.

Stop the engine and keep heat, sparks and flame away.

Handle fuel only outdoors.

Wipe up spills immediately.

4.

5.

6.

After refueling, turn the fuel fill cap clockwise until it clicks.

Insert the breather tube into the handlebar cover hole.

If the fuel valve was set to RES, turn the fuel valve ON.

If you replace the fuel fill cap, use only a Honda Genuine replacement part.

104


０９／０５／１１１４：５７：０８３１ＨＰ４８３００１１４

Engine Oil & Filter

Engine oil quality is a major factor that affects both the performance and the service life of the engine.

Using the proper oil (page 106 ) and filter, and regularly checking, adding, and changing oil will help extend your engine’s life. Even the best oil wears out. Changing oil helps get rid of dirt and deposits in the engine. Operating the engine with old or dirty oil can damage your engine. Running the engine with insufficient oil can cause serious damage to the engine and transmission.

Change the engine oil as specified in the maintenance schedule on page 92 . When running in very dusty conditions, oil changes should be performed more frequently than specified in the maintenance schedule.


105

０９／０５／１１１４：５７：２３３１ＨＰ４８３００１１５


Oil Recommendation

API classification viscosity (weight)

JASO T 903 standard suggested oil

＊

SG or higher except oils labeled as energy conserving on the circular API service label

SAE 10W-30

MA

Pro Honda GN4 4-stroke oil or an equivalent motorcycle oil.

＊

Suggested oils are equal in performance to SJ oils that are not labeled as energy conserving on the circular API service label.

Your ATV does not need oil additives. Use the recommended oil.

Do not use oils with graphite or molybdenum additives. They may adversely affect clutch operation.

Do not use API SH or higher oils displaying a circular API ‘‘energy conserving’’ service label on the container. They may affect lubrication and clutch performance.

NOT RECOMMENDED OK

Do not use non-detergent, vegetable, or castor based racing oils.

106


０９／０５／１１１４：５７：３１３１ＨＰ４８３００１１６


Other viscosities shown in the following chart may be used when the average temperature in your riding area is within the indicated range.

JASO T 903 standard

The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines.

There are two classes: MA and MB.

Oil conforming to the standard is labeled on the oil container. For example, the following label shows the MA classification.

(1)

(2)

(1) code number of the sales company of the oil

(2) oil classification


107

０９／０５／１１１４：５７：４２３１ＨＰ４８３００１１７


Checking & Adding Oil

Refer to


on page 89 .

Check the engine oil level each day before operating your ATV and add if needed.

Bef ore riding your ATV, check the engine oil level.

1.

2.

3.

4.

Park your ATV on a firm, level surface.

Start the engine in a well-ventilated area and let it idle for 3 minutes. Stop the engine and wait 2

−

3 minutes.

Remove the seat (page 100 ).

−

5

LEFT SIDE

(1) left side cover

108


(1)

０９／０５／１１１４：５７：５３３１ＨＰ４８３００１１８


5.

6.

wipe it clean.

Insert the oil filler cap/dipstick without screwing it in, then remove the oil filler cap/dipstick and check the oil level. The oil level should

7.

the oil filler cap/dipstick.

If required, add the specified oil into the filler cap hole, up to the

8.

9.

upper level mark on the oil filler cap/dipstick. Do not overfill.

Reinstall the oil filler cap/dipstick.

Install the left side cover.

10.

Install the seat.

Running the engine with an improper oil level can cause serious engine damage.

LEFT SIDE

(2)

(2) oil filler cap/dipstick

(3)

(4)

(3) upper level mark

(4) lower level mark


109

０９／０５／１１１４：５８：０５３１ＨＰ４８３００１１９


Changing Engine Oil & Filter

Refer to


on page 89 .

Your ATV’s oil filter has very specific performance requirements. Use a new Honda Genuine oil filter specified for your model or a filter of equal quality.

Using the wrong oil f ilter may result in leaks or engine damage.

This procedure requires mechanical skill and professional tools such as a torque wrench as well as a means for disposing of the drained fluid

(page 182 ). If you do not have the skills or the tools, see your Honda dealer.

Drain the Engine Oil:

1.

With the ATV on the level ground, remove the seat (page side cover (page crankcase.

108

100 ), left

) and the oil filler cap/dipstick from the front

2.

Place an oil drain pan under the crankcase and remove the engine oil

UNDER ENGINE

(2)

(1)

(1) engine oil drain plug

110


(2) sealing washer

０９／０５／１１１４：５８：１３３１ＨＰ４８３００１２０

Install a New Engine Oil Filter:

1.


2.

RIGHT SIDE


(1) right side cover

(1)

(cont’d)


111

０９／０５／１１１４：５８：２４３１ＨＰ４８３００１２１


3.

manner (page 182 ).

4.

5.

then install a new oil filter. Use only the Honda Genuine oil filter or a filter of equivalent quality specified for your model. Using the wrong

Honda filter or a non-Honda filter which is not of equivalent quality may cause engine damage.

on the filter body, near the seal.

Improper installation of the oil f ilter can cause serious engine damage.

RIGHT SIDE

(4) (5)

(8)

(6)

(2)

(2) oil filter cover

(3) bolts

(4) oil filter

(5) O-rings

(3)

112


(7)

(2)

(3)

(6) spring

(7) rubber seal

(8) ‘‘OUTSIDE’’ mark

０９／０５／１１１４：５８：３９３１ＨＰ４８３００１２２


6.

Reinstall the oil filter cover, making sure the bolts are tightened to the specified torque:

7 lbf·ft (10 N·m , 1.0 kgf·m)

7.

Pour the drained oil into a suitable container and dispose of it in an approved manner (page 182 ).

Improper disposal of drained f luids is harmf ul to the environment.

8.

Install the right side cover.

Add Engine Oil:

1.

Reinstall the oil drain plug with a new sealing washer, and tighten it to the specified torque:

18 lbf·ft (25 N·m , 2.5 kgf·m)

2.

Fill the crankcase with the recommended grade oil approximately:

3.0 US qt (2.8 )

3.

Reinstall the oil filler cap/dipstick.

4.

5.

Start the engine and let it idle for 3

Stop the engine, wait 2 −

− 5 minutes.

3 minutes and check the oil level. Make sure

6.

7.

the oil is between the upper and lower level marks on the oil filler cap/dipstick. If necessary, add more oil but do not overfill.

Check that there are no oil leaks.


8.

Install the seat.

If a torque wrench is not used for installation, see your Honda dealer as soon as possible to verify proper assembly.


113

０９／０５／１１１４：５８：４９３１ＨＰ４８３００１２３

Gear Case Oil


type viscosity (weight) suggested oil

Changing Oil

hypoid gear oil

SAE 80

Honda shaft drive oil or equivalent

Refer to


on page 89 .

Change the oil with the gear case at normal operating temperature to assure complete and rapid draining.

114


０９／０５／１１１４：５９：０２３１ＨＰ４８３００１２４

Gear Case Oil

1.

Park the ATV on level ground.

2.

3.

Check that the drain plug sealing washer is in good condition. If necessary, replace the sealing washer.

4.

After the oil has completely drained, reinstall the drain plug and tighten it to the specified torque:

5.

9 lbf·ft (12 N·m , 1.2 kgf·m)



6.

Fill the gear case with the recommended oil.

2.5 US oz (75 cm )

7.

8.

Install the oil filler cap and oil level check bolt.

REAR (2)

(4)

(3)

(1) oil drain plug

(2) oil filler cap

(1)

(3) oil level check bolt

(4) oil level check hole


115

０９／０５／１１１４：５９：１３３１ＨＰ４８３００１２５

Differential Oil

(Except TRX420TE )


type viscosity (weight) suggested oil

Changing Oil

hypoid gear oil

SAE 80

Honda shaft drive oil or equivalent

Refer to


on page 89 .

Change the oil with the differential at normal operating temperature to assure complete and rapid draining.

116


０９／０５／１１１４：５９：２６３１ＨＰ４８３００１２６

Differential Oil


1.

Park the ATV on level ground.

2.

3.

Check that the drain plug sealing washer is in good condition. If necessary, replace the sealing washer.

4.

After the oil has completely drained, reinstall the drain plug and tighten it to the specified torque:

5.

9 lbf·ft (12 N·m , 1.2 kgf·m)



6.

Fill the differential with the recommended oil.

7.8 US oz (230 cm )

Make sure the oil level is at the lower edge of the oil filler inspection

7.

Install the oil filler cap.

FRONT

(3)

(1)

(1) oil drain plug

(2) oil filler cap

(2)

(3) oil filler inspection hole


117

０９／０５／１１１４：５９：３４３１ＨＰ４８３００１２７

Coolant

Your ATV’s liquid cooling system dissipates engine heat through the coolant jacket that surrounds the cylinder and cylinder head.

Maintaining the coolant will allow the cooling system to work properly and prevent freezing, overheating, and corrosion.

Coolant Recommendation

Use Pro Honda HP coolant or an equivalent high quality ethylene glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines. Check the antifreeze container label.

Use only distilled water as a part of the coolant solution. Water that is high in mineral content or salt may be harmful to the aluminum engine.

Using coolant with silicate inhibitors may cause premature wear of water pump seals or blockage of radiator passages. Using tap water may cause engine damage.

The factory provides a 50/50 solution of antifreeze and water in this

ATV. This coolant solution is recommended for most operating temperatures and provides good corrosion protection.

Decreasing the concentration of antifreeze to less than 40% will not provide proper corrosion protection.

118


０９／０５／１１１４：５９：４５３１ＨＰ４８３００１２８

Coolant

Increasing the concentration of antifreeze is not recommended because it decreases cooling system performance. Higher concentrations of antifreeze (up to 60%) should only be used to provide additional protection against freezing. Check the cooling system frequently during freezing weather.

Checking & Adding Coolant

Refer to


on page 89 .

Check the engine coolant level each day before operating your ATV and add if needed.

RIGHT REAR

(2)

(1)

(3)

(1) reserve tank

(2) UPPER level mark

(3) LOWER level mark

1.

2.

Make sure the vehicle is on level ground.

With the engine at normal operating temperature, check the coolant

2

If the reserve tank is empty, or if coolant loss is excessive, check for leaks and see your Honda dealer for repair.

(cont’d)


119

０９／０５／１１１４：５９：５６３１ＨＰ４８３００１２９

Coolant

3.

4.

5.


Always add coolant to the reserve tank. Do not attempt to add coolant by removing the radiator cap.

6.

Add coolant to the reserve tank as required to bring the coolant level to the UPPER level mark.

REAR

(5)

(4)

(6)

(4) rubber strap

(5) rear fender cover

(6) reserve tank cap

7.

After adding coolant, install the reserve tank cap and rear fender cover.

8.

9.

Fasten the rubber strap.

Install the seat.

120


０９／０５／１１１５：００：０４３１ＨＰ４８３００１３０

Coolant

Coolant Replacement

Refer to


on page 89 .

Coolant should be replaced by your Honda dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Service Manual (page 224 ).

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

To properly dispose of drained coolant, refer to

You & the Environment,

page 182 .



121

０９／０５／１１１５：００：１７３１ＨＰ４８３００１３１

Coolant

Radiator Core

Refer to


on page 89 .

Check the air passages for clogging or damage. Remove insects, mud, or any obstruction with low water pressure. Have the radiator checked by your Honda dealer if the air flow is restricted over more than 20% of the radiator surface.

Clean the radiator core after riding the ATV in mud.

To clean the radiator core and radiator grill plate:

1.

2.

3.

101

Do not apply pressured water directly to the radiator core. The pressured water can damage the radiator core.

FRONT (6)

(5)

(3)

(4)

(1)

(1) tabs A

(2) radiator grill under cover

(3) clips

(3)

122


(2)

(4) radiator grill covers

(5) tabs B

(6) couplers

０９／０５／１１１５：００：２５３１ＨＰ４８３００１３２

4.

5.

6.

Install the removed parts in reverse order of removal.

FRONT

Coolant

(7) radiator grill plate

(8)

(8) radiator core

(7)


123

０９／０５／１１１５：００：３３３１ＨＰ４８３００１３３

Air Cleaner

Refer to


on page 89 .

Proper air cleaner maintenance is very important for off-road vehicles.

A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt, dust, mud, and other impurities to pass into the engine.

Service the air cleaner more frequently if you ride in unusually wet or dusty areas. Your Honda dealer can help you determine the correct service interval for your riding conditions.

Your ATV’s air cleaner has very specific performance requirements.

Use a new Honda Genuine air cleaner specified for your model or an air cleaner of equal quality.

Using the wrong air cleaner may result in premature engine wear.

Proper air cleaner maintenance can prevent premature engine wear or damage, expensive repairs, low engine power, poor gas mileage, and spark plug fouling.

Improper or lack of proper air cleaner maintenance can cause poor perf ormance and premature engine wear.

124


０９／０５／１１１５：００：４２３１ＨＰ４８３００１３４

Air Cleaner

Cleaning

1.


UNDER SEAT

(1)

2.

3.

(1) retainer clips

(2)

(2) air cleaner housing cover

(cont’d)


125

０９／０５／１１１５：００：５４３１ＨＰ４８３００１３５

Air Cleaner

4.

the air cleaner housing.

5.

6.

Remove the air cleaner ( ) from the air cleaner body ( 7 ).

7.

Gently wash the air cleaner in clean, non-flammable (high flash point) solvent such as kerosene − not gasoline. After cleaning, gently squeeze out the remaining solvent. Avoid twisting or wringing the air cleaner. This can tear the foam.

8.

Inspect for tears or cracks in the foam or seams of the air cleaner.

Replace the air cleaner if it is damaged.

9.

Allow the air cleaner to dry thoroughly before applying oil. A wet air cleaner will not fully absorb the oil.

10.

Pour clean Pro Honda Foam Filter Oil or an equivalent over the entire surface of the air cleaner. Use both hands to evenly spread the oil into the air cleaner. Gently squeeze out any excess oil. (To keep your hands dry, place the air cleaner in a clean plastic bag before spreading the oil into the air cleaner.)

UNDER SEAT

(7) (3) (4)

(3)

(5)

(6)

(3) screw

(4) air cleaner assembly

(5) clamp

126


(6) air cleaner

(7) air cleaner body

０９／０５／１１１５：０１：０３３１ＨＰ４８３００１３６

Air Cleaner

11.

Install the air cleaner on the air cleaner body.

12.

Apply a thin coat of grease to the sealing surface of the air cleaner assembly.

13.

Install the clamp.

14.

Insert the air cleaner assembly into the air cleaner housing.

15.

Fasten the screw.

16.

Reassemble by reversing the disassembly sequence.

Install the air cleaner housing cover with the FRONT mark ( 8 ) facing forward and fit the cut out of the tab ( 9 ) at the end of the air cleaner.

UNDER SEAT

(8)

(9)

(8) FRONT mark (9) tab

(9)


127

０９／０５／１１１５：０１：１０３１ＨＰ４８３００１３７

Air Cleaner

Dust Cover

UNDER SEAT

(1) (2)

(1) dust cover

If the dust cover is dirty, clean it.

(2) breather joint

128


０９／０５／１１１５：０１：１８３１ＨＰ４８３００１３８

Air Cleaner

Air Cleaner Housing Drain Tube

The air cleaner housing drain tube should be serviced in accordance with the Maintenance Schedule. (Riding through water may require more frequent inspection.) If deposits can be seen in the drain tube, the tube must be cleaned before starting the vehicle.

REAR

(3) (2)

(1)

(3) air cleaner housing (1) drain tube

(2) clip

1.

2.

3.

Drain the deposits.

Reinstall the drain tube, securing it with the clip.


129

０９／０５／１１１５：０１：３１３１ＨＰ４８３００１３９

Throttle

Throttle Freeplay

Refer to


on page 89 .

RIGHT HANDLEBAR

( A )

(B)

1/8

−

5/16 in

(3

−

8 mm)

(2)

(3) (4)

(1) throttle lever

(2) rubber sleeve

(3) throttle cable adjuster

(1)

(4) lock nut

(A) decrease freeplay

(B) increase freeplay

Inspection

Freeplay:

1/8 − 5/16 in (3 − 8 mm)

Adjustment

1.

2.

3.

4.

5.

Turn the adjuster to obtain the correct freeplay.

Tighten the lock nut and reinstall the sleeve.

After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions.

130


０９／０５／１１１５：０１：４０３１ＨＰ４８３００１４０

Throttle

Throttle Inspection

Refer to


on page 89 .

1.

Check that the throttle assembly is positioned properly and the securing bolts are tight.

2.

Check for smooth operation of the throttle lever from fully open to fully closed in all steering positions. If there is a problem, see your

3.

Honda dealer.

Inspect the condition of the throttle cable from the throttle lever down

4.

5.

to the throttle body. If the cable is kinked or chafed, have it replaced.

Check the throttle cable for tension or stress in all steering positions.

Lubricate the throttle cable with a commercially available cable lubricant to prevent premature wear and corrosion.


131

０９／０５／１１１５：０１：５５３１ＨＰ４８３００１４１

Clutch System

Your ATV’s shift-activated, wet, multiplate clutch is part of the primary drive system. Proper adjustment allows a smooth, gradual engagement when shifting gears.

Clutch Adjustment

Refer to


on page 89 .

LEFT FRONT

(1)

(2)

(1) lock nut (2) clutch adjuster

1.

2.

3.

4.

5.

Make sure the engine is cool.

Make sure the ignition switch is OFF ( ).

Remove the seat (page 100 ) and left side cover (page 108 ).

6.

resistance.

Turn the adjuster 1/4 turn clockwise, then tighten the lock nut to hold

7.

the adjuster in this position.

After adjustment, start the engine and test ride your ATV to be sure the clutch is operating properly.

8.

Install the removed parts in reverse order of removal.

If you cannot get proper adjustment, or the clutch does not work properly, the clutch friction discs may be worn. See your Honda dealer or refer to official Honda Service Manual (page 224 ).

132


０９／０５／１１１５：０２：０８３１ＨＰ４８３００１４２

Reverse Lock System

Reverse Lock System Adjustment

Refer to


on page 89 .

LEFT HANDLEBAR

(1)

(6)

1/16

−

3/16 in

(2

−

4 mm)

(4) (5)

(1) dust cover

(2) reverse assist lever

(3) rear brake lever

(4) rubber sleeve

(5) lock nut

(6) adjusting nut

1.

2.

1/16 − 3/16 in (2 − 4 mm)

3.

4

4.

After adjustment, tighten the lock nut securely.

Return the dust cover and rubber sleeve.

(2) (3)

Other Checks

Check the reverse assist lever and cable for loose connections or other damage. If the cable is worn or kinked, have it replaced by your Honda dealer.


133

０９／０５／１１１５：０２：２０３１ＨＰ４８３００１４３

Spark Plug

Spark Plug Recommendation

standard spark plug BKR5E-11 (NGK) or

K16PR-U11 (DENSO)

Use only the recommended type of spark plug in the recommended heat range.

Using spark plugs with an improper heat range can cause engine damage.

Spark Plug Inspection & Replacement

Refer to


on page 89 .

1.

2.

Remove the seat (page 100 ) and left side cover (page 108 ).

LEFT SIDE

(1)

(2)

(1) left tank side cover

134


(2) bolts

０９／０５／１１１５：０２：３３３１ＨＰ４８３００１４４

Spark Plug

3.

4.

Clean any dirt from around the spark plug base.

5.

spark plug wire when disconnecting the cap.

Using a spark plug wrench provided in the tool kit, remove the spark

6.

plug.

Inspect the electrodes and center porcelain for deposits, corrosion, or carbon fouling. If the corrosion or deposits are heavy, replace the plug. Clean a carbon or wet-fouled plug with a plug cleaner, if available, or a wire brush. Inspect the spark plug electrodes for wear.

7.

Discard the spark plug if there is apparent wear or if the insulator is cracked or chipped.

8.

insulator tip appear unusually fouled or burned, we suggest that you contact your Honda dealer.

adjustment is necessary, bend the side electrode carefully.

The gap should be:

0.039

− 0.043 in (1.00

− 1.10 mm)

LEFT SIDE

(6)

0.039

−

0.043 in

(1.00

−

1.10 mm)

(5)

(4)

(3)

(3) spark plug cap

(4) center electrode

(5) side electrode

(6) spark plug gap

(cont’d)


135

０９／０５／１１１５：０２：４３３１ＨＰ４８３００１４５

Spark Plug

9.

With the plug washer attached, thread the spark plug in by hand to prevent cross-threading.

10.

Tighten the spark plug:

If the old plug is good:

1/8 turn after it seats.

If installing a new plug, tighten it twice to prevent loosening: a) First, tighten the plug:

NGK:

DENSO:

3/4


turn after it seats.

b) Then loosen the plug.

c) Next, tighten the plug again:


An improperly tightened spark plug can damage the engine. If a plug is too loose, a piston may be damaged. If a plug is too tight, the threads may be damaged.

11.

Connect the spark plug cap. Take care to avoid pinching any cables or wires.

12.

Install the remaining parts in the reverse order of removal.

136


０９／０５／１１１５：０２：５０３１ＨＰ４８３００１４６

Valves

Valve Inspection

Refer to


on page 89 .

Valve clearance should be: intake: exhaust:

0.006 in (0.15 mm)

0.009 in (0.23 mm)

Excessive clearance will cause noise. Insufficient clearance will cause loss of power and possibly damage the valves.

For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official

Honda Service Manual. Otherwise, the valves should be adjusted by your Honda dealer.


137

０９／０５／１１１５：０３：００３１ＨＰ４８３００１４７

Spark Arrester

Refer to


on page 89 .

The spark arrester must be serviced every 100 operating hours to maintain its efficiency.

Regular servicing prevents carbon build up (which can diminish engine performance) and also complies with USDA regulations for regular maintenance to assure proper function. The spark arrester prevents random sparks from the combustion process in your engine from reaching the environment.

The use of safety glasses is recommended for this procedure.

Because of the possible fire hazard, check that there are no combustible materials in the area before purging the spark arrester.

REAR

(1)

(1) bolt

1.

Select a well-ventilated area free of combustible materials and make sure the exhaust pipe is cool.

2.

3.

4.

5.

Start the engine and rev it up approximately twenty times while momentarily creating exhaust system back pressure by blocking the end of the muffler with a shop towel.

Stop the engine and allow the exhaust pipe to cool.

Reinstall the bolt securely.

138


０９／０５／１１１５：０３：１０３１ＨＰ４８３００１４８

Suspension

Your front and rear suspension systems use springs and hydraulic damping devices that suspend your weight and most of the weight of your ATV.

The oil damper systems hydraulically control the natural compression and rebound of the suspension springs so that traction and comfort are maintained as the wheels ride over rough terrain.

(Except TRX420TE)

The spring pre-loads for your front and rear suspension systems adjust the amount of force required to begin compression of the spring.

Consider adjusting your suspensions pre-load whenever you change your normal load, by adding or subtracting cargo accessories, or when riding conditions change.

The way you ride your ATV and the type of ride you want to experience can also influence your suspension needs.

Lower spring pre-load provides a softer ride and is usually preferred for light loads and smooth terrain. Higher spring pre-load provides a firmer ride and is recommended for heavy loads, rough terrain, and faster, more challenging riding.

Suspension Adjustment (Except TRX420TE )

Using a pin spanner, which is available from your Honda dealer, the suspension can be adjusted for rider weight and riding conditions by changing the spring pre-load.

Do not attempt to disassemble, service, or dispose of the damper; see your Honda dealer. The instructions found in this owner’s manual are limited to adjustments of the shock assembly only.


139

０９／０５／１１１５：０３：２１３１ＨＰ４８３００１４９

Suspension

Suspension Spring Pre-Load (Except TRX420TE )

Refer to


on page 89 .

FRONT REAR

(1) (1)

1 2 3 4 5

(2)

(1) spring pre-load adjuster

(2) pin spanner riding conditions.

(2) 1 2 3 4 5

140


０９／０５／１１１５：０３：２７３１ＨＰ４８３００１５０

Suspension

Position 1: for a light load and smooth terrain.

Position 2: standard position.

Positions 3 to 5: for when the ATV is more heavily loaded. (Also increase spring pre-load for stiffer suspension.)

Make sure that both shock absorbers are adjusted to the same position.

Always adjust the shock absorber position in sequence (1-2-3-4-5 or 5-

4-3-2-1). Attempting to adjust directly from 1 to 5 or 5 to 1 may damage the shock absorber.


141

０９／０５／１１１５：０３：３７３１ＨＰ４８３００１５１

Brakes

The hydraulic disc brakes (front) and single mechanical drum brake

(rear) on your ATV dissipate heat generated by the friction of the brake pads on the disc (front) and the brake shoes on the drums (rear) as the wheels are slowed.

Hydraulic Disc Front Brake

As the front brake pads wear, brake fluid level will drop. A leak in the system will also cause the level to drop.

There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks.

If the right brake lever freeplay does not feel within the normal range while riding, check the brake pads for wear (page 145 ).

Worn pads should be replaced. If the pads are not worn beyond the recommended limit, there is probably air in the brake system. See your

Honda dealer to have the air bled from the system.

Mechanical Drum Rear Brake

If the rear brake lever/parking brake lever or brake pedal freeplay does not feel within the normal range while riding, check the brake shoes for wear (page 150 ).

Brake Fluid Recommendation

brake fluid Honda DOT 4 Brake Fluid

The recommended brake fluid is Honda DOT 4 Brake Fluid, or any brake fluid of equal quality and performance. Use fresh brake fluid from a sealed container. Be sure to read the label before opening the sealed container. An opened container may be contaminated or may have absorbed moisture from the air.

142


０９／０５／１１１５：０３：４６３１ＨＰ４８３００１５２

Brakes

Fluid Level Inspection

Refer to


on page 89 .

If your inspection indicates a low fluid level, have your Honda dealer add the recommended fluid.

Do not add or replace brake fluid, except in an emergency. If you do add fluid, have your Honda dealer check the system as soon as possible.

Brake f luid can damage plastic and painted surf aces. Handle with care.

Wipe up spills immediately. Avoid brake fluid contact with skin or eyes.

If it comes in contact with your eyes, wash them out with clean water and immediately call a doctor. If it comes in contact with your skin, wash with clean water and, if necessary, call a doctor.

RIGHT HANDLEBAR

(1) LOWER level mark

(1)


143

０９／０５／１１１５：０３：５３３１ＨＰ４８３００１５３

Brakes

With the ATV in an upright position, check the fluid level.

below the LOWER level mark, check the brake pads for wear

(page 145 ).

Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.

Other Inspection

Make sure there are no fluid leaks.

Check for deterioration or cracks in the hoses and fittings. If the hoses are worn or cracked, have them replaced by your Honda dealer.

144


０９／０５／１１１５：０４：０２３１ＨＰ４８３００１５４

Brakes

Brake Pad Wear

Refer to


on page 89 .

Brake pad wear will depend upon the severity of usage and riding conditions. The pads will wear faster in wet or muddy conditions.

Inspect the pads visually during all regular service intervals to determine the pad wear.

RIGHT FRONT (Left side similar)

(2)

(1)

(1) wear indicator (2) edge of reference mark dealer for this replacement.

Always inspect both pads in both the right and left front brake calipers.


145

０９／０５／１１１５：０４：１０３１ＨＰ４８３００１５５

Brakes

Rear Brake Pedal Freeplay

RIGHT SIDE

(1)

9/16

−

13/16 in

(15

−

20 mm)

(1) rear brake pedal

Inspection starts to take hold. Freeplay, measurement at the tip of the end of the pedal, should be:

9/16 − 13/16 in (15 − 20 mm)

If necessary, adjust to the specified range.

146


０９／０５／１１１５：０４：１９３１ＨＰ４８３００１５６

Brakes

Adjustment

RIGHT REAR

(3) (2)

(2) brake pedal adjusting nut

(3) brake arm pin

1.

rod at the rear of the frame. Make sure the cutout on the adjusting nut

2.

then check the clearance between the brake arm and the brake arm pin.

(4) brake arm

(4)


147

０９／０５／１１１５：０４：２７３１ＨＰ４８３００１５７

Brakes

Rear Brake Lever Freeplay

LEFT HANDLEBAR

(1)

9/16

−

13/16 in

(15

−

20 mm)

(1) rear brake lever/parking brake lever

Inspection before the brake starts to take hold. Freeplay (measurement at the tip of the end of the brake lever) should be:

9/16 − 13/16 in (15 − 20 mm)

If necessary, adjust to the specified range.

148


０９／０５／１１１５：０４：３７３１ＨＰ４８３００１５８

Adjustment

RIGHT REAR

(3)

Brakes

(2)

(2) brake lever adjusting nut

(3) brake arm pin

Adjust the freeplay of the rear brake lever/parking brake lever with the front wheels pointed straight ahead.

1.

rod at the rear of the frame. Make sure the cutout on the adjusting nut

2.

Adjust the freeplay of the rear brake lever/parking brake lever. Push and the brake arm pin.

(4) brake arm

(4)


149

０９／０５／１１１５：０４：４９３１ＨＰ４８３００１５９

Brakes

Other Inspection

Check that the brake lever and brake pedal assemblies are positioned properly and the securing bolts are tight.

Make sure that the brake cables, brake arm, spring, parking, and fasteners are in good condition.

Brake Shoe Wear

Refer to


on page 89 .

The rear brake is equipped with an external brake wear indicator that lets you check brake wear without disassembly. Application of the brake control causes the arrow on the brake arm to move toward a reference mark on the brake panel.

RIGHT REAR

(2)

(1) arrow

(2) brake arm

(1) (3)

(3) reference mark

1.

2.

Replace the brake shoe if the arrow aligns with the reference mark replacement is necessary, see your Honda dealer.

150


０９／０５／１１１５：０４：５８３１ＨＰ４８３００１６０

Brakes

Brakelight Switch Adjustment

Refer to


on page 89 .

Rear Brake Only: behind the engine from time to time. The brakelight should turn on at

0.6 in (15 mm) of pedal stroke. See

Rear Brake Pedal Freeplay

, page 146 the switch operates too soon.

RIGHT REAR

(1)

( B )

( A )

(2)

(1) rear brakelight switch

(2) adjusting nut


151

０９／０５／１１１５：０５：０５３１ＨＰ４８３００１６１

Brakes

Draining Water from Brakes

Refer to


on page 89 .

RIGHT REAR

(1)

(1) rear brake drain bolt

1.

Make sure the engine is OFF and the parking brake is set.

2.

brake panel.

If any water drains, the brake seals must be replaced by your Honda dealer as soon as possible.

152


０９／０５／１１１５：０５：１１３１ＨＰ４８３００１６２

Tires

To safely operate your ATV, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

This ATV is equipped with low pressure tubeless tires. Although the tires are designed specifically for off-road use, they are not immune to punctures. Always select your riding area with care.

The following pages give detailed information on how and when to check your air pressure, how to inspect your tires for wear and damage, and our recommendations for tire repair and replacement.


153

０９／０５／１１１５：０５：１７３１ＨＰ４８３００１６３

Tires

Air Pressure

Refer to


on page 89 .

Properly inflated tires provide the best combination of handling, tread life, and riding comfort. Generally, underinflated tires wear unevenly, adversely affect handling, and are more likely to fail from being overheated. Overinflated tires make your ATV ride harshly, are more prone to damage from surface hazards, and wear unevenly.

Make sure the air valve caps are secure. If necessary, install new caps.

154


０９／０５／１１１５：０５：２７３１ＨＰ４８３００１６４

Tires

Always check air pressure when your tires are ‘‘cold.’’ If you check air pressure when your tires are ‘‘warm’’ − even if your ATV has only been ridden for a few miles − the readings will be higher. If you let air out of warm tires to match the recommended cold tire pressures, the tires will be underinflated. Be sure to check tire pressure at the riding site, since changes in altitude can affect air pressure.

The recommended ‘‘cold’’ tire pressures are:

(TRX420TE/FE)

FRONT

RECOMMENDED

PRESSURE

REAR

3.6 psi (25.0 kPa) 3.6 psi (25.0 kPa)

(TRX420FPE)

RECOMMENDED

PRESSURE

FRONT REAR

4.4 psi (30.0 kPa) 3.6 psi (25.0 kPa)


155

０９／０５／１１１５：０５：３６３１ＨＰ４８３００１６５

Tires

A manually operated tire pump should be used rather than the high pressure system found in service stations. This will minimize the possibility of tire damage from overinflation. If you use a high pressure system at a service station, add air in small amounts and check the pressure increase frequently to prevent possible tire damage from overinflation.

Operating this ATV with improper tires, or with uneven tire pressure may cause loss of control, and you could be seriously injured or killed.

Always use the size and type tires specified in this owner’s manual for this vehicle.

Always maintain proper tire pressure as described in this owner’s manual.

Inspection

Refer to


on page 89 .

Whenever you check the tire pressures, you should also look for:

Bumps or bulges in the side of the tire or the tread. Replace any tire that has a bump or bulge.

Cuts, slits, or cracks in the tires. Replace the tire if you can see fabric or cord.

Nails or other foreign objects embedded in the side of the tire or tread.

Excessive tread wear.

156


０９／０５／１１１５：０５：４８３１ＨＰ４８３００１６６

Tires

Also, if you hit a pothole or other hard object while riding, stop as soon as you safely can and carefully inspect the tires for damage.

Tread Wear

FRONT

NEW

REAR

(2)

Replace

3/16 in

(4 mm)

Replace

3/16 in

(4 mm)

(1)

(3)

NEW

(1) groove depth

(2) wear indicator

(3) wear indicator location mark

For best performance, you should replace a tire before the tread depth at the center reaches the following limits: front rear

3/16 in (4 mm)

3/16 in (4 mm)


157

０９／０５／１１１５：０５：５６３１ＨＰ４８３００１６７

Tires

Tire Repair

Refer to


on page 89 .

A tire that is repaired, either temporarily or permanently, will have lower speed and performance limits than a new or undamaged tire.

A temporary repair can sometimes be made in an emergency situation.

However, since a temporary repair may not hold, you must ride very slowly, preferably without any cargo, and have the tire replaced or permanently repaired as soon as possible. (For more information on temporary repairs, see

If You Have a Flat Tire,

page 192 .)

A permanent repair, such as an internal plug patch, can be made if a tire has only a small puncture in the tread area. However you may not be able to safely carry as much weight. If you choose to have a tire repaired, be sure the repair work is performed by a professional.

If you have a tire professionally repaired at a non-Honda facility, we recommend that you have the work checked by your Honda dealer.

158


０９／０５／１１１５：０６：０９３１ＨＰ４８３００１６８

Tires

Tire Replacement

Refer to


on page 89 .

The tires that came on your ATV were designed to match the performance capabilities of your ATV and provide the best combination of handling, braking, and comfort.

It is best to replace all four tires, however if that is not possible, you must replace the tires in pairs (front or rear) with tires of the same size and type as the originals. Never replace just one tire.

Installing improper tires on your ATV can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

The recommended tires for your ATV are: front rear

AT24

AT24

×

×

8-12 ★★

10-11 ★★

MAXXIS M977

MAXXIS M978

When you replace a tire, remember:

Have the tire replaced by your Honda dealer if possible.

If you have a tire professionally replaced at a non-Honda facility, we recommended that you have the work checked by your Honda dealer.


159

０９／０５／１１１５：０６：１８３１ＨＰ４８３００１６９

Guards

Skid Plate & Engine Guard

Refer to


on page 89 .

(1) engine guard

(1) (2)

(2) skid plate plate for cracks, damage or looseness at intervals shown in the

Maintenance Schedule.

Have the engine guard and skid plate replaced if they are cracked or damaged. If the guard and plate bolts are loose, tighten them securely.

160


０９／０５／１１１５：０６：２５３１ＨＰ４８３００１７０

Front Boot Guards & Front Driveshaft Guards


Refer to


on page 89 .

Guards

(1) front boot guards

(2)

(1)

(2)

(2) front driveshaft guards cracks, damage or looseness.

Tighten any loose fasteners. Replace the front boot guards and front driveshaft guards as required.


161

０９／０５／１１１５：０６：３２３１ＨＰ４８３００１７１

Drivetrain Boots

Propeller Shaft Boots & Yoke Joint Boot

Refer to


on page 89 .

(1) (2)

(1) rubber propeller shaft boots (Except TRX420TE)

(2) rubber yoke joint boot replace them.

162


０９／０５／１１１５：０６：４０３１ＨＰ４８３００１７２

Drivetrain Boots

Front Driveshaft Boots (Except TRX420TE )

Refer to


on page 89 .

(1) rubber driveshaft boots

(1) grease. If necessary, have your Honda dealer replace them.


163

０９／０５／１１１５：０６：４８３１ＨＰ４８３００１７３

Battery

Your ATV has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water as you would with a conventional-type battery.

Your battery is a maintenance-f ree type and can be permanently damaged if the cap strip is removed.

Electrical accessories use current from the battery, even when the ignition is OFF. Limited operation also allows the battery to discharge.

If you have electrical accessories on your ATV or do not ride frequently, we recommend that you charge the battery frequently (see

Battery

Charging,

page 168 ).

If you do not expect to ride your ATV for at least two weeks, we recommend you remove the battery, or at least disconnect the battery cables (negative cable first).

If you plan to store your ATV, see

Battery Storage,

page 165 .

If your battery seems weak and/or is leaking electrolyte (causing slow starting or other electrical problems), see your Honda dealer.

WARNING:

Battery posts, terminals and related accessories contain lead and lead compounds.

Wash your hands after handling.

164


０９／０５／１１１５：０６：５６３１ＨＰ４８３００１７４

Battery

Battery Storage

Refer to


on page 89 .

If you plan to store your ATV, we recommend you remove the battery and store it where it can be charged at least every 30 days to maintain its service life.

If you do not remove the battery, we recommend disconnecting the battery cables (negative cable first).

You will get the best storage results from removing the battery and slow charging it every 30 days (see

Battery Charging,

page 168 ).

Before you remove the battery, be sure to read all the information that follows, as well as the information on the battery label.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.


165

０９／０５／１１１５：０７：０８３１ＨＰ４８３００１７５

Battery

The battery is located in a compartment under the rear fender cover.

UNDER REAR FENDER COVER

(4) (1)

(3)

(2)

(1) rubber band

(2) negative ( − ) terminal lead

(3) battery

(4) positive ( ＋ ) terminal lead

Removal

1.

Make sure the ignition switch is OFF ( ).

2.

3.


Remove the rear fender cover (page 120 ).

4.

5.

Disconnect the negative (

−

2 first, then disconnect the positive (

＋

4

3

166


０９／０５／１１１５：０７：２１３１ＨＰ４８３００１７６

Battery

6.

Remove the battery.

7.

Charge the battery (see following section), unless you have been riding regularly.

8.

Store your battery in an easy-to-reach location off the floor, in an area protected from freezing temperature and direct sunlight.

9.

Clean the compartment after removing the battery for storage. Dry the compartment and, if paint is missing, re-paint the area.

10.

Slow charge the battery (see following section) once every 30 days.

Installation

1.

2.

3.

battery band.

Make sure the battery band is properly position.

Reinstall in the reverse order of removal.

Be sure to connect the positive ( ＋ ) terminal first, then the negative

( − ) terminal.

4.

Make sure all bolts and other fasteners are secure.

(5)

1.6 in

(40 mm)

(5) battery band


167

０９／０５／１１１５：０７：２９３１ＨＰ４８３００１７７

Battery

Battery Charging

Refer to


on page 89 .

(1)

(1) charger

Be sure to read the information that came with your battery charger and follow the instructions on the battery. Improper charging may damage the battery.

Honda, which can be purchased from your Honda dealer. These units can be left connected for long periods without risking damage to the battery. However, do not intentionally leave the charger connected longer than the time period recommended in the charger’s instructions.

Avoid using an automotive-type battery charger. An automotive charger can overheat an ATV battery and cause premature damage.

168


０９／０５／１１１５：０７：４０３１ＨＰ４８３００１７８

Appearance Care

Frequent cleaning and polishing will keep your Honda looking newer longer.

Frequent cleaning also identifies you as an owner who values his ATV.

A clean ATV is also easier to inspect and service.

General Recommendations

Refer to


on page 89 .

To clean your ATV, you may use:

− water

− a mild, neutral detergent and water

− a mild spray and wipe cleaner/polisher

− a mild spray and rinse cleaner/degreaser and water

Avoid products that contain harsh detergents or chemical solvents that could damage the metal, paint, and plastic on your ATV.

If your ATV is still warm from recent operation, give the engine and exhaust system time to cool off.

Park in a shady area. Washing your ATV in bright sunlight may cause the finish to fade because water droplets intensify the sun’s brightness.

Spotting is also more likely because surface water can dry before you have time to wipe it off.

Clean your ATV regularly to protect surface finishes.

We recommend the use of a garden hose to wash your ATV. High pressure washers (like those at coin-operated car washers) can damage certain parts of your ATV.

High pressure water (or air) can damage certain parts of your ATV.

After cleaning, inspect for damage, wear, and leaks (fuel, oil, coolant and brake fluid).


169

０９／０５／１１１５：０７：５２３１ＨＰ４８３００１７９

Appearance Care

Washing Your ATV with a Mild Detergent

Refer to


on page 89 .

1.

2.

Rinse your ATV thoroughly with cool water to remove loose dirt.

Fill a bucket with cool water. Mix in a mild, neutral detergent, such as dish washing liquid or a product made especially for washing motorcycles or automobiles.

3.

Wash your ATV with a sponge or soft towel. As you wash, check for heavy grime. If necessary, use a mild cleaner/degreaser to remove the

4.

grime.

After washing, rinse your ATV thoroughly with plenty of clean water

5.

to remove any residue. Detergent residue can corrode alloy parts.

Dry your ATV with a chamois or a soft towel. Leaving water on the

6.

surface to air dry can cause dulling and water spots. As you dry, inspect for chips and scratches.

Start the engine and let it idle for several minutes. The engine heat will help dry moist areas.

7.

As a precaution, ride your ATV at a slow speed and apply the brakes several times. This will help dry the brakes and restore normal braking performance.

If the inside of the headlight lens appears clouded immediately after washing, it should clear after a few minutes of riding.

170


０９／０５／１１１５：０８：０５３１ＨＰ４８３００１８０

Appearance Care

Spray Cleaning Your ATV

Refer to


on page 89 .

Avoid using spray cleaner products on the tires or suspension components.

Suggestions for using spray cleaner(s) follow:

ATV condition

Dust and fingerprint smudges.

Light road grimes.

Heavy grime. Oil leaks.

Brake dust.

Dull, corroded chrome or aluminum.

Recommended Cleaning

Apply a spray cleaner/polish and wipe paint, chrome, glass, and clear plastic.

Spray any difficult-to-reach or very dirty areas with a spray cleaner/ degreaser.

Rinse and dry.

Apply a spray cleaner/polish and wipe with a non-abrasive cloth.

Use a spray cleaner/degreaser. If necessary, rub with a sponge.

Rinse and dry.

Apply a spray cleaner/polish and wipe with a non-abrasive cloth.

Apply a high quality chrome/ aluminum polish and wipe with a non-abrasive cloth.


171

０９／０５／１１１５：０８：１１３１ＨＰ４８３００１８１

Appearance Care

Finishing Touches

Refer to


on page 89 .

After washing your ATV, consider using a commercially available spray cleaner/polish or quality liquid or paste wax to finish the job. Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Apply the polish or wax according to the instructions on the container.

If a surface on your ATV is chipped or scratched, your Honda dealer has touch-up paint to match your ATV’s color. Be sure to use your

ATV’s color code (page 209 ) when you buy touch-up paint.

If the frame has a chip that exposes the metal, first apply primer (to prevent corrosion) and then apply the touch-up paint. Several thin layers of touch-up paint are better than one thick coat.

172


０９／０５／１１１５：０８：２１３１ＨＰ４８３００１８２

Tips

Here’s helpful advice on how to prepare for an off-road adventure, how to transport and store your Honda, and how to be an environmentally responsible ATV owner.

Preparing for a Ride ..........................................................................

.

What to Take to the Riding Area ..................................................

.

What to Take on the Trail .............................................................

.

Transporting Your Honda .................................................................

.

Storing Your Honda ..........................................................................

.

Preparation for Storage .................................................................

.

Removal from Storage ..................................................................

.

You & the Environment ....................................................................

.

174

174

175

176

178

179

181

182

Tips

173

０９／０５／１１１５：０８：３１３１ＨＰ４８３００１８３

Preparing for a Ride

A safe and enjoyable ride begins with good planning and preparation.

Always ride with at least one other person in case you have trouble, and let someone know where you’re going and when you expect to return.

Before riding in an unfamiliar area, find out in advance if you need special permits, get maps so you can study the terrain, and talk to other riders who know the area. The Forest Service and the Bureau of Land

Management riding clubs, and off-road magazines are good sources of information.

What to Take to the Riding Area

Along with your ATV and riding gear, you should take along some tools and supplies in case you have a problem. For some of the difficulties you might encounter, see

Taking Care of the Unexpected,

which begins on page 183 .

We recommend that you always take water, food, a first aid kit, and your owner’s manual. Other items you should consider loading on your truck or trailer include: a tool kit tire repair supplies and tools, and tires extra parts, control levers, cables, and spark plugs wire, duct tape, and rope extra gasoline

For safety, all refueling should be done at a gas station on the way to the riding area or at your base camp.

174

Tips

０９／０５／１１１５：０８：３７３１ＨＰ４８３００１８４

Preparing for a Ride

What to Take on the Trail

What you take with you during a ride depends on the kind of terrain, how long you expect to ride, how far you might go from your base camp or help, and how experienced you or your companions are in making repairs.

If you decide to take some tools, spare parts, or other supplies on the trail, be sure you can carry them safely and know how to use them. Also, be sure to follow the loading guidelines and weight limit (page 48 ).

Tips

175

０９／０５／１１１５：０８：４４３１ＨＰ４８３００１８５

Transporting Your Honda

Do not tow your ATV behind a car or other vehicle.

When you transport your ATV, we recommend that you carry the vehicle in its normal operating position (on all four wheels). Do not incline the vehicle upright on its rear end. This can damage the vehicle, and leaking gasoline could be a hazard.

Follow these procedures:

1.

2.

Set the parking brake.

Turn the fuel valve OFF.

176

Tips

０９／０５／１１１５：０８：５３３１ＨＰ４８３００１８６

Transporting Your Honda

3.

Secure the vehicle with tie-down straps in the areas shown.

Suitable tie-down straps are available from your Honda dealer.

4.

Ordinary rope is not recommended because it can stretch under load.

Using tie-down straps in any other areas can damage your ATV.

Rock the vehicle back and forth to make sure the tie-down straps are tight and the vehicle is secure.

(1)

(2)

(3)

(1) front cargo rack

(2) rear cargo rack

(3) trailer hitch

Tips

177

０９／０５／１１１５：０８：５９３１ＨＰ４８３００１８７

Storing Your Honda

If you won’t be riding for an extended period, such as during the winter, thoroughly inspect your ATV and correct any problem before storing it.

That way, needed repairs won’t be forgotten and it will be easier to get your ATV running again.

For more information about storage, refer to the

Guide,

available from your Honda dealer.

Honda Winter Storage

We suggest you perform the following procedures to keep your ATV in top condition. These storage procedures will reduce the deterioration that can occur during storage.

178

Tips

０９／０５／１１１５：０９：１１３１ＨＰ４８３００１８８


Preparation for Storage

Refer to


on page 89 .

1.

2.

Change the engine oil and filter (page 110 ).

Make sure the cooling system is filled with a 50/50% antifreeze solution (page 118 ).

3.

4.

5.

Fill the fuel tank. Make sure the fuel fill cap is properly installed.

Check that the fuel valve is OFF.

To prevent rusting in the cylinder, perform the following:

Remove the spark plug cap from the spark plug.

Remove the spark plug.

Do not connect the spark plug to the spark plug cap.

Pour a tablespoon (15 − 20 cc) of clean engine oil into the cylinder and cover the spark plug hole with a piece of cloth.

With the engine stop switch in the RUN ( ) position, press the start button several times to crank the engine and distribute the oil.

Reinstall the spark plug and spark plug cap.

(cont’d)

Tips

179

０９／０５／１１１５：０９：２０３１ＨＰ４８３００１８９


6.

Remove the battery and charge it fully. Store it in an area protected from freezing temperatures and direct sunlight. Slow charge the battery (page 168 ) once a month.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

7.

8.

Wash and dry your ATV. Wax all painted surfaces.

Inflate the tires to their recommended pressures (page 155 ).

9.

Store your ATV in an unheated area, free of dampness, away from sunlight, with a minimum of daily temperature variation.

10.

Place your ATV on blocks to lift all tires off the floor.

11.

Cover your ATV with a porous material. Avoid using plastic or similar non-breathing, coated materials that restrict air flow and allow heat and moisture to accumulate.

180

Tips

０９／０５／１１１５：０９：２９３１ＨＰ４８３００１９０


Removal from Storage

Refer to


on page 89 .

1.

Uncover and clean your ATV.

2.

If your ATV has been stored for more than four months − change

3.

the engine oil (page 110 ).

If your ATV has been stored for more than two months − ask your

Honda dealer to drain and replace the fuel.

4.

5.

Charge the battery (page 168 ) as required. Install the battery.

Perform a pre-ride inspection (page low speeds.

43 ), then test-ride your ATV at

Tips

181

０９／０５／１１１５：０９：３７３１ＨＰ４８３００１９１

You & the Environment

Owning and riding an ATV can be enjoyable, but you must do your part to protect nature. When you show respect for the land, wildlife, and other people, you also help preserve the sport of off-road riding.

Following are tips on how you can be an environmentally responsible

ATV owner.

Tread Lightly.

Stay on existing roads and trails, avoid surfaces that are easily damaged, and ride only in areas approved for off-road vehicles.

Keep the Noise Down.

Loud vehicles can be offensive. Ride as quietly as possible, don’t remove your spark arrester, and don’t modify the muffler or any other part of your air intake and exhaust systems. Such modifications not only increase noise, they also reduce engine performance and may be illegal.

Choose Sensible Cleaners.

Use a biodegradable detergent when you wash your ATV. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Don’t throw cleaning solvents away; see the following guidelines for proper disposal.

Recycle Wastes.

It’s illegal and thoughtless to put used engine oil in the trash, down a drain, or on the ground. Used oil, gasoline, and cleaning solvents contain poisons that can hurt refuse workers and contaminate our drinking water, lakes, rivers, and oceans. Before changing your oil, make sure you have the proper containers. Put oil and other toxic wastes in separate sealed containers and take them to a recycling center. Call your local or state office of public works or environmental services to find a recycling center in your area, and to get instructions on how to dispose of non-recyclable wastes.

182

Tips

０９／０５／１１１５：０９：４８３１ＨＰ４８３００１９２

Taking Care of the Unexpected

With all the challenges you can encounter off-road, there’s a chance that sometime something may go wrong. This section gives practical advice to help you deal with a wide range of problems. Take time to read this section before you ride. Also review the tips in

Preparing f or a Ride

(page 174 ).

General Guidelines ............................................................................

.

If Your Engine Quits or Won’t Start .................................................

.

If the Shift Switches Do Not Function ..............................................

.

Emergency Gear Selection & Operation ...........................................

.

If You Have a Flat Tire .....................................................................

.

If the High Coolant Temperature Indicator Lights ............................

.

If a Fuse Blows .................................................................................

.

If You Crash ......................................................................................

.

If You Lose Your Key ......................................................................

.

If the Battery Is Low (or Dead) .........................................................

.

If a Component Fails .........................................................................

.

184

186

189

190

192

196

198

203

204

205

206


183

０９／０５／１１１５：０９：５６３１ＨＰ４８３００１９３


General Guidelines

Keeping your ATV well-maintained is the best way to reduce the possibility of having a problem while riding. However, problems can arise even with well-maintained machines.

Remember to take along your owner’s manual, the tool kit that came with your ATV, and any other items (such as tire repair supplies and additional tools) that might help you solve a problem on your own.

If something goes wrong during a ride, the first thing to do is stop as soon as you safely can. Do not continue riding if you have a flat tire, or you hear an unusual noise, or your ATV just doesn’t feel right. If you continue riding, you could cause more damage and endanger your own safety.

After stopping, take time to assess the situation. Carefully inspect your

ATV to identify the problem, then consider your options before you decide what to do.

If a problem is relatively minor and you have the tools, supplies, and skills to make a permanent repair, you may be able to fix it on the trail and continue riding. Or, you may be able to make a temporary repair that allows you to slowly ride back to your base where you can make a permanent repair or get help.

When a problem is more serious

− or you don’t have the tools, supplies, experience, or time to deal with it − you need to choose the safest way to get yourself and your ATV back to base. For example, if you are close enough, you (or you and another person) might be able to push it back.

184


０９／０５／１１１５：１０：０４３１ＨＰ４８３００１９４


Should you ever have a problem while riding, please follow these guidelines:

Always put personal safety first.

Take time to assess the situation and your options before deciding what to do.

If the problem is relatively minor and you have the tools, supplies, and skills to make a temporary repair, be sure to have permanent repairs made as soon as possible.

Do not continue riding if you are hurt or your ATV is not in safe riding condition.

Additional recommendations for specific problems follow.


185

０９／０５／１１１５：１０：１０３１ＨＰ４８３００１９５

If Your Engine Quits or Won’t Start

Proper operation and maintenance can prevent starting and engine performance problems. In many cases, the cause of the problem may be a simple operational oversight.

If you have a problem starting the engine − or experience poor engine performance − the following information may help you. If you can’t correct the problem, see your Honda dealer.

If your ATV won’t start, listen as you press the start button. If you don’t hear the starter motor turning, refer to the

Starter motor doesn’t operate

symptom. If you can hear the starter motor working normally, refer to the

Starter motor works, but the engine won’t start

symptom.

186


０９／０５／１１１５：１０：３２３１ＨＰ４８３００１９６


SYMPTOM:

Starter motor doesn’t operate.

POSSIBLE CAUSE WHAT TO DO ignition switch OFF engine stop switch

Turn the ignition switch ON.

Slide the engine stop switch to RUN.

OFF transmission not in neutral blown fuse

Shift into neutral.

battery lead loose low (or dead) battery faulty starter motor

Replace with a new fuse of the same rating (page 198 ).

Tighten the battery lead.

Charge the battery (page 168 ).

If charging doesn’t help, see your

Honda dealer.

If all possible causes are negative, the starter motor may be faulty. See your Honda dealer.

SYMPTOM:

Starter motor works, but the engine won’t start.

POSSIBLE CAUSE out of fuel

WHAT TO DO flooded engine loose or unconnected spark plug cap loose battery cables weak battery

Fill the fuel tank.

See

F looded Engine

(page 62 ).

Install the spark plug cap securely. If the engine still won’t start, see your

Honda dealer.

Tighten the battery terminal bolts.

Charge the battery (page 168 ). If charging doesn’t help, see your

Honda dealer.


187

０９／０５／１１１５：１０：５１３１ＨＰ４８３００１９７


SYMPTOM:

Engine starts, but runs poorly.

POSSIBLE CAUSE WHAT TO DO high coolant temperature

Check the high coolant temperature indicator. Refer to

If the High

Coolant T emper atur e Indicator

Lights,

page 196 .

See your Honda dealer.

runs erratically, misfires blubbers (rich fuel mixture) sooty exhaust (rich fuel mixture) detonates or pings under load



afterfires (backfires) pre-ignition (runs on after ignition switched OFF)

If applicable, switch to the recommended octane gasoline

(page 102 ) or change your brand of gasoline. If the problem persists, see your Honda dealer.



SYMPTOM:

Engine starts, but runs poorly or dies when hot.

POSSIBLE CAUSE poor or inadequate fuel flow due to clogged fuel filter

WHAT TO DO


(ensure clean fuel supply)

188


０９／０５／１１１５：１１：０１３１ＨＰ４８３００１９８

If the Shift Switches Do Not Function

If one or both shift switches do not function, see the following instructions. If proper function cannot be restored, see your Honda dealer.

When the engine is running:

1.

Stop the ATV.

2.

3.

Turn the ignition switch to the ‘‘OFF’’ ( ) position.

After the engine stops, turn the ignition switch to the ‘‘ON’’ ( )

4.

5.

position.

Press both shift switches and check that they are functioning.

If both switches are functioning, shift into neutral and restart the engine.

If one or both switches are not functioning, see

Emergency Gear

Selection & Operation,

page 190 .

When the engine is stopped and the ignition switch is ‘‘ON’’:

1.

Turn the ignition switch to the ‘‘OFF’’ ( ) position.

2.

3.

Turn the ignition switch to the ‘‘ON’’ ( ) position.

Press both shift switches and check that they are functioning.

4.

If both switches are functioning, shift into neutral and restart the engine.

If one or both switches are not functioning, see

Emergency Gear

Selection & Operation,

page 190 .

When the battery is low (or dead):

See

If the Battery Is Low (or Dead),

page 205 .


189

０９／０５／１１１５：１１：０８３１ＨＰ４８３００１９９

Emergency Gear Selection & Operation

If the shift switches do not operate, use the following procedure to manually select a gear so you may drive the vehicle to a location where it can be loaded and transported to a Honda dealer.

1.

Turn the ignition switch to the ‘‘ON’’ ( ) position.

2.

3.

4.


Remove the gear change tool from underside of the seat (page

Check the neutral indicator.

98 ).

If the transmission is in neutral, go to step 5.

If the transmission is not in neutral, remove the left side cover

(page 108 ), use the gear change tool to shift to neutral so you will be able to start the engine, Refer to

How to Shif t Gears Manually

5.

6.

7.

(page 191 ).

Apply the parking brake.

Press the start button to start the engine.

Select the gear you want. For running on level ground: use 3rd or 4th gear. For mountainous roads: use 2nd or 3rd gear. Refer to

How to

Shif t Gears Manually

(page

8.

9.


191 ).

Return the gear change tool to underside of the seat.

10.

Install the seat.

11.

Get on the ATV. Drive it at a safe speed to a place where it can be repaired or serviced.

190


０９／０５／１１１５：１１：１７３１ＨＰ４８３００２００

Emergency Gear Selection & Operation

How to Shift Gears Manually:

( A )

( B )

(A) downshift (counterclockwise) (B) upshift (clockwise)

With the ATV unoccupied, align the hexagonal hole of the gear change tool with the hexagonal end of the secondary spindle which is located on the front crankcase.

If the transmission does not shift, rock the vehicle back and forth and try again.

Return the gear change tool to underside of the seat.

Do not attempt to shift gears manually using the gear change tool while riding.

If the transmission is shifted manually when the electric shift system is functioning, the system will shutdown automatically and the shift switches will not operate. To reactivate the system, turn the ignition switch to the ‘‘OFF’’ ( ) position, then turn it back to the ‘‘ON’’

( ) position.


191

０９／０５／１１１５：１１：２６３１ＨＰ４８３００２０１

If You Have a Flat Tire

How you handle a flat tire on the trail depends on how serious the tire damage is, and what tools and supplies you have with you.

If you have a slow leak or a minor puncture, use the plug method to make a temporary repair. (The plug method is applied from the outside of the tire and is the same as that for conventional tubeless tires.)

A plug-type repair kit, available at most auto parts stores or service stations, provides a plug, an installation tool, tire cement, and an instruction sheet. Follow the instructions provided with the repair kit to make a temporary repair.

As soon as possible, have the tire permanently repaired by your Honda dealer. Any tire that cannot be repaired should be replaced.

Whenever the ATV is to be operated far from service facilities or available transportation, we recommend that you carry a tire pump and a repair kit with the vehicle.

If the leak is more serious, or a temporary repair doesn’t hold, the tire must be replaced. The tire will also need to be replaced if it is damaged

(page 159 ). Replacing a tire involves removing and re-installing the wheel (page 194 ).

If you are unable to repair a flat tire on the trail, you will need to send for help. We strongly recommend that you do not try to ride with a flat tire. The ATV will be hard to handle, and if the tire comes off the rim, it may lock up the wheel and cause you to crash.

192


０９／０５／１１１５：１１：３０３１ＨＰ４８３００２０２


Riding your ATV with a temporary tire repair can be risky.

If the temporary repair fails, you can crash and be seriously injured or killed. If you must ride with a temporary tire repair, ride slowly and carefully until the tire is permanently repaired or replaced.


193

０９／０５／１１１５：１１：４２３１ＨＰ４８３００２０３


Emergency Wheel Removal/Installation

Refer to


on page 89 .

(1)

(1) wheel nuts

(1) (2)

(2) wheel rim

Removal

1.

Park your ATV on a firm, level surface.

2.

3.

Loosen − but do not remove − 1

4.

5.

Raise the front (or rear) wheels off the ground and place a support block under the vehicle.

Remove the wheel nuts.

Remove the wheel.

Avoid getting grease, oil, or dirt on the front brake disc or pad surfaces when removing and installing each wheel. Any contamination can cause poor brake performance or rapid pad wear after reassembly.

194


０９／０５／１１１５：１１：４９３１ＨＰ４８３００２０４


Installation

1.

Position the wheel.

2.

Position the wheel nuts so that the tapered sides face the wheel

3.

Hand-tighten the wheel nuts on the wheel, then lower the ATV to the ground before tightening the nuts in a crisscross (rather than circular) pattern to the specified torque:

47 lbf·ft (64 N·m , 6.5 kgf·m)

If a torque wrench was not used for installation, see your Honda dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capability.


195

０９／０５／１１１５：１１：５８３１ＨＰ４８３００２０５

If the High Coolant Temperature

Indicator Lights

Normally, the high coolant temperature indicator will only light momentarily when you turn the ignition ON ( ). Occasionally, it may flicker at or near idling speed.

High coolant temperature may be caused by restriction of air flow to the radiator (such as mud caked on the radiator), extended idling, an oil leak, a coolant leak, a low oil level, a low coolant level, or extended operation under adverse conditions.

If the indicator comes on while you’re riding, don’t ignore it. Pull safely to a stop. Stop the engine as soon as it’s safe to do so, and let it cool.

Continuing to ride with high coolant temperature or an overheated engine can cause serious engine damage.

A steaming engine indicates a coolant leak. Shut the engine off and wait until the steaming stops. Look for a leak, but don’t touch the engine or radiator system. Let everything cool off first.

Check for any restriction of air flow to the radiator.

If there’s no obvious problem, leave the engine on so the fan and coolant circulating system can continue working. Monitor the high coolant temperature indicator. The indicator may turn off after a brief stop with no load on the engine.

Check the radiator fan.

If the fan is not working, turn the engine off. Open the fuse box

(page 199 ) and check the radiator fan fuse. If the fuse is blown, replace it with the proper (same rating) spare fuse. Start the engine. If the high coolant temperature indicator comes on and stays on, turn the engine off.

If the radiator fan is working, visually check the coolant level in the reserve tank, located under the rear fender. It isn’t necessary to touch the radiator system.

196


０９／０５／１１１５：１２：０６３１ＨＰ４８３００２０６

If the High Coolant Temperature

Indicator Lights

If the reserve tank is low or empty, don’t ride without adding coolant

(page 119 ). After adding coolant, turn the engine on and check the high coolant temperature indicator.

If the indicator doesn’t turn off, do not ride. The engine needs repair.

Transport your ATV to a Honda dealer (page 176 ).

If the temperature drops to normal, check the coolant level. If it has gone down, add more coolant.

Check for an oil leak.

Check the oil level. If necessary, add the recommended oil (page 108 ) to the upper level mark. If you must leave your ATV to get oil, secure it as much as possible.

Start the engine, and check that the high coolant temperature indicator goes off.

If you are able to resume riding, continue to monitor the high coolant temperature indicator frequently.

If there is an oil leak − do not ride the ATV until the leak is repaired by

Honda dealer (page 176 ).

If there’s a mild coolant leak, you can ride for awhile, carefully watching the indicator. Be prepared to stop and add more coolant or water. If the leak is bad, transport your ATV to a Honda dealer

(page 176 ).


197

０９／０５／１１１５：１２：１９３１ＨＰ４８３００２０７

If a Fuse Blows

All of the electrical circuits on your ATV have fuses to protect them from damage caused by excess current flow (short circuit or overload).

If something electrical on your ATV stops working, the first thing you

Check all the fuses before looking elsewhere for another possible cause of the problem. Replace any blown fuses and check component operation.

(1)

(1) blown fuse

The main fuse and the circuit fuses are located under the rear fender cover.

TRX420FPE only:

The PS (Electric Power Steering) fuse is located under the rear fender cover.

Recommended Fuses main fuse shift motor fuse other fuse

PS (Electric Power

Steering) fuse

(TRX420FPE only)

30 A

30 A

15 A, 10 A

40 A

× 3

198


０９／０５／１１１５：１２：３０３１ＨＰ４８３００２０８

If a Fuse Blows

Main Fuse Access

1.

To prevent an accidental short circuit, turn the ignition switch OFF

2.

3.

( ) before checking or replacing the fuses.



4.


(4)

(3)

(2) (5)

(2) main fuse

(3) shift motor fuse

5.

Pull the main fuse out.

(4) fuse box cover

(5) spare main fuse

(cont’d)


199

０９／０５／１１１５：１２：４０３１ＨＰ４８３００２０９

If a Fuse Blows

Circuit Fuse Access

(7)

(6) circuit fuses

6.

retaining clips.

(6)

(7) spare fuses

If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating.

Replacing a f use with one that has a higher rating greatly increases the chance of damage to the electrical system.

7.

8.

9.

Install the fuse box cover.

Install the rear fender cover.

Install the seat.

200


０９／０５／１１１５：１２：５０３１ＨＰ４８３００２１０

If a Fuse Blows

PS (Electric Power Steering) Fuse Access

1.

(TRX420FPE only)

Turn the ignition switch OFF ( ) before checking the fuse.

2.

3.

4.



5.

6.

If the PS fuse is blown, see your Honda dealer for this service.

Install the PS fuse box cover.

Install the seat.


(2)

(1)

(1) PS fuse (2) PS fuse box cover


201

０９／０５／１１１５：１２：５６３１ＨＰ４８３００２１１

If a Fuse Blows

If you do not have a spare fuse and you cannot ride the ATV without fixing the problem, take a fuse of the same rating or a lower rating from one of the other circuits that you can do without temporarily.

If you replace a blown fuse with a spare fuse that has a lower rating, replace the fuse with the correct rating as soon as you can. Also remember to replace any spare fuses that were installed.

If the replacement fuse of the same rating burns out in a short time, there is probably a serious electrical problem on your ATV. Leave the blown fuse in that circuit and have your ATV checked by your Honda dealer.

202


０９／０５／１１１５：１３：０２３１ＨＰ４８３００２１２

If You Crash

Personal safety is your first priority after a crash. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. If you cannot ride safely, send someone for help. Do not ride if you will risk further injury.

If you decide you are capable of riding safely, carefully inspect your

ATV for damage and determine if it is safe to ride. Check the tightness of critical nuts and bolts securing such parts as the handlebar, control levers, brakes, and wheels.

If there is minor damage, or you are unsure about possible damage but decide to try riding the ATV back to your base, ride slowly and cautiously.

Sometimes, crash damage is hidden or not immediately apparent. When you get home, thoroughly check your ATV and correct any problems you find. Also, be sure to have your Honda dealer check the frame and suspension after any serious crash.


203

０９／０５／１１１５：１３：０９３１ＨＰ４８３００２１３

If You Lose Your Key

at the rear of the manual. You’ll need this number to have a duplicate key made.

If you lose your key and aren’t carrying a duplicate, either get your spare or have one made. If you don’t know your key number, call the dealer where you purchased your Honda ATV. They may have it listed in their records. If they don’t, transport your ATV to them or the nearest

Honda dealer. The dealer will probably have to remove the ignition switch assembly to find the key number so they can make a key for you.

(1)

(1) key number

204


０９／０５／１１１５：１３：１４３１ＨＰ４８３００２１４

If the Battery Is Low (or Dead)

Jump starting is not recommended, especially if you use an automobile battery. The greater amperage of an automobile battery when the car engine is running can damage your ATV’s electrical system.

Bump starting is also not recommended.

If you can’t charge the battery or it appears unable to hold a charge, contact your Honda dealer.


205

０９／０５／１１１５：１３：２０３１ＨＰ４８３００２１５

If a Component Fails

The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Making a trailside repair depends on how serious the damage is and what tools and supplies you have with you.

If any component of the brake system is damaged, you may be able to ride carefully back to your base using the other brake components for slowing or stopping.

If you damage a throttle cable or other critical component, your ATV may be unsafe to ride. Carefully assess the damage and make any repairs that you can. But if there is any doubt, it’s best to be conservative and safe.

206


０９／０５／１１１５：１３：２７３１ＨＰ４８３００２１６

Technical Information

This section contains dimensions, capacities, and other technical data, plus information on government requirements and how to break-in your

ATV.

Vehicle Identification ........................................................................

.

Specifications ....................................................................................

.

Break-in Guidelines ..........................................................................

.

Emission Control Systems .................................................................

.

Oxygenated Fuels ..............................................................................

.

208

210

215

216

220


207

０９／０５／１１１５：１３：３５３１ＨＰ４８３００２１７

Vehicle Identification

Serial Numbers

The VIN, engine serial number, and key number may be required when ordering replacement parts. You may record these numbers in the Quick

Reference section at the rear of this manual.

FRONT

(1) crankcase.

LEFT SIDE

(1) VIN

(2)

(2) engine number

208


０９／０５／１１１５：１３：４３３１ＨＰ４８３００２１８

Vehicle Identification

Color Label & Code

seat (page 100 ) to check the label.

The color code is helpful when ordering replacement parts. You may record the color and code in the Quick Reference section at the rear of this manual.

UNDER SEAT

(1)

(1) color label


209

０９／０５／１１１５：１４：０１３１ＨＰ４８３００２１９

Specifications

Dimensions

overall length overall width overall height wheelbase

80.9 in (2,055 mm)

46.1 in (1,172 mm)

45.2 in (1,148 mm) ......TRX420TE

45.1 in (1,146 mm) ......TRX420FE

TRX420FPE

49.4 in (1,256 mm) ......TRX420TE

49.2 in (1,249 mm) ......TRX420FE

TRX420FPE

6.5 in (165 mm) ground clearance

Fuel & Lubricants

fuel recommendation fuel tank capacity fuel tank reserve engine oil capacity engine oil recommendation unleaded gasoline, pump octane number of 86 or higher

3.51 US gal (13.3 ) including reserve

0.69 US gal (2.6 ) after disassembly:

3.3 US qt (3.1 ) after draining:

2.9 US qt (2.7 ) after draining & oil filter change:

3.0 US qt (2.8 )

API Service Classification SG or higher except oils labeled as energy conserving on the circular API service label, SAE 10W-30, JASO T

903 standard MA,

Pro Honda GN4 4-stroke oil or an equivalent motorcycle oil

210


０９／０５／１１１５：１４：２１３１ＨＰ４８３００２２０

Specifications

Fuel & Lubricants (cont’d)

cooling system recommendation

Pro Honda HP Coolant or an equivalent high quality ethylene cooling system capacity glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines

1.6 US qt (1.5 )

Capacities

passenger capacity maximum weight capacity operator only

485 lb (220 kg) rider, all cargo and accessories

Engine Specifications

displacement bore & stroke compression ratio spark plug

(standard) spark plug gap valve clearance

(cold) idle speed

25.6 cu-in (420 cm )

3.41

× 2.81 in (86.5

× 71.5 mm)

9.9 : 1

BKR5E-11 (NGK) or

K16PR-U11 (DENSO)

0.039

− 0.043 in (1.00

− 1.10 mm) intake:

0.006 in (0.15 mm) exhaust:

0.009 in (0.23 mm)

1,400 ± 100 rpm

(NO ADJUSTMENT)


211

０９／０５／１１１５：１４：４５３１ＨＰ４８３００２２１

Specifications

Power Transmission

primary reduction secondary reduction final reduction transmission ratio front rear

(Except TRX420TE)

1st

2nd

3rd

4th

5th reverse final drive

2.103

1.818

3.231

3.154

3.857

2.235

1.571

1.178

0.848

4.831

shaft

Chassis & Suspension

caster trail tire size, front tire size, rear tire pressure, front & rear (cold)

6.34

…TRX420TE

3.0

° …TRX420FE

TRX420FPE

0.99 in (25.1 mm) …TRX420TE

0.35 in (9.0 mm) …TRX420FE

TRX420FPE

AT24 × 8-12

AT24 × 10-11 front:

★★

★★

MAXXIS M977

MAXXIS M978

3.6 psi (25.0 kPa) …TRX420TE

TRX420FE

4.4 psi (30.0 kPa) …TRX420FPE rear:

3.6 psi (25.0 kPa)

212


０９／０５／１１１５：１５：０６３１ＨＰ４８３００２２２

Specifications

Electrical

battery generator

Lights

headlight brake/tail light neutral indicator reverse indicator high coolant temperature indicator

PGM-FI indicator

4WD indicator

(Except TRX420TE)

PS (Electric Power

Steering) indicator

(TRX420FPE only)

Fuses

main shift motor other

PS (Electric Power

Steering)

(TRX420FPE only)

12 V − 12 Ah

0.359 kW/5,000 rpm

12 V 30/30 W

LED

LED

LED

LED

LED

LED

LED

×

30 A

30 A

15 A, 10 A × 3

40 A

2


213

０９／０５／１１１５：１５：１６３１ＨＰ４８３００２２３

Specifications

Torque Specification

engine oil drain bolt engine oil filter cover bolts rear final gear case oil drain bolt differential oil drain bolt

(Except TRX420TE) wheel nuts

18 lbf·ft (25 N·m , 2.5 kgf·m)

7 lbf·ft (10 N·m , 1.0 kgf·m)

9 lbf·ft (12 N·m , 1.2 kgf·m)

9 lbf·ft (12 N·m , 1.2 kgf·m)

47 lbf·ft (64 N·m , 6.5 kgf·m)

214


０９／０５／１１１５：１５：２０３１ＨＰ４８３００２２４

Break-in Guidelines

Help assure your ATV’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles

(25 km).

During this period, avoid full-throttle starts, rapid acceleration, and constant rpm operation.


215

０９／０５／１１１５：１５：２７３１ＨＰ４８３００２２５

Emission Control Systems

Exhaust Emission Requirements

The U.S. Environmental Protection Agency (EPA) and the California

Air Resources Board (CARB) require that your ATV comply with applicable exhaust emissions standards during its useful life, when operated and maintained according to the instructions provided.

left side of the frame.

LEFT FRONT

(1)

(1) vehicle emission control information label

216


０９／０５／１１１５：１５：３５３１ＨＰ４８３００２２６


Source of Exhaust Emissions

The combustion process produces carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight.

Carbon monoxide does not react in the same way, but it is toxic.

Honda Motor Co., Ltd. utilizes various systems to reduce carbon monoxide, oxides of nitrogen and hydrocarbons.

Exhaust Emission Control System

The exhaust emission control system includes a PGM-FI system.

No adjustment to this system should be made although periodic inspection of the components is recommended.

The exhaust emission control system is separate from the crankcase emission control system.

Crankcase Emission Control System

The engine is equipped with a closed crankcase system to prevent discharging crankcase emissions into the atmosphere. Blow-by gas is returned to the combustion chamber through the air cleaner.


217

０９／０５／１１１５：１５：４２３１ＨＰ４８３００２２７


Problems That May Affect ATV Exhaust Emissions

If you are aware of any of the following symptoms, have the vehicle inspected and repaired by your Honda ATV dealer.

Symptoms:

1.

Hard starting or stalling after starting

2.

3.

Rough idle

Misfiring or backfiring during acceleration

4.

5.

After-burning (backfiring)

Poor performance (driveability) and poor fuel economy

Federal regulations prohibit removing or disabling a device or element of design that may affect your engine’s emission performance unless your ATV will be used exclusively in competition. If you modify your engine for use in sanctioned competition events, you must deface or destroy the emission control information label.

218


０９／０５／１１１５：１５：５０３１ＨＰ４８３００２２８


Noise Emission Control System

TAMPERING WITH THE NOISE CONTROL SYSTEM IS

PROHIBITED: removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is design has been removed or rendered inoperative by any person.

AMONG THOSE ACTS PRESUMED TO CONSTITUTE

TAMPERING ARE THE FOLLOWING ACTS:

1.

Removal of, or puncturing the muffler, baffles, header pipes or any other component which conducts exhaust gases.

2.

3.

4.

Removal of, or puncturing of any part of the intake system.

Lack of proper maintenance.

Replacing any moving parts of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the manufacturer.

Fuel Permeation Emission Control System

This vehicle complies with the Fuel Permeation Emission Control regulations of the U.S. Environmental Protection Agency (EPA) and the

California Air Resources Board (CARB).

The fuel tank, fuel hoses, and fuel vapor charge hoses used on this vehicle incorporate fuel permeation control technologies.

Tampering with the fuel tank, fuel hoses, or fuel vapor charge hoses to reduce or defeat the effectiveness of the fuel permeation technologies is prohibited by federal regulations.


219

０９／０５／１１１５：１５：５７３１ＨＰ４８３００２２９

Oxygenated Fuels

Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States use oxygenated fuels to help reduce emissions.

If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.

Before using an oxygenated fuel, try to confirm the fuel’s contents.

Some states/provinces require this information to be posted on the pump.

The following are the EPA-approved percentages of oxygenates:

ETHANOL (ethyl or grain alcohol) 10% by volume

You may use gasoline containing up to 10% ethanol by volume.

Gasoline containing ethanol may be marketed under the name

‘‘Gasohol’’.

MTBE (Methyl Tertiary Butyl Ether) 15% by Volume

You may use gasoline containing up to 15% MTBE by volume.

METHANOL (methyl or wood alcohol) 5% by Volume

You may use gasoline containing methanol containing up to 5% methanol by volume as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also damage metal, rubber, and plastic parts of your fuel system.

220


０９／０５／１１１５：１６：０３３１ＨＰ４８３００２３０

Oxygenated Fuels

If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.

Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates mentioned above are not covered under warranty.

Oxygenated fuels can damage paint and plastic. Be careful not to spill fuel when filling the fuel tank. Wipe up any spills immediately.

Oxygenated f uels can damage paint and plastic. Damage caused by spilled f uel is not covered by warranty.


221

０９／０５／１１１５：１６：０６３１ＨＰ４８３００２３１

222


０９／０５／１１１５：１６：１４３１ＨＰ４８３００２３２

Consumer Information

This section contains information on your warranty and how to get an official Honda service manual.

Authorized Manuals ..........................................................................

.

Warranty Coverage ...........................................................................

.

Warranty Service ...............................................................................

.

Contacting Honda .............................................................................

.

Your Honda Dealer ...........................................................................

.

The Honda Rider’s Club ...................................................................

.

224

227

228

229

230

231


223

０９／０５／１１１５：１６：２２３１ＨＰ４８３００２３３

Authorized Manuals

The Service Manual used by your authorized Honda dealer is available from Helm, Inc.

Also available but not necessary to service your model is the Honda

Common Service Manual which explains theory of operation and basic service information for various systems common to all Honda motorcycles, motor scooters and ATVs.

These Honda manuals are written for the professional technician, but most mechanically capable owners should find them easy to use if they have the proper tools and observe proper safety standards.

Special Honda tools are necessary for some procedures.

Publication Item No.

61HP403

61CM002

31HP4830

Description

2010 TRX420 TE/TM/FE/FM/FPE/FPM

Service Manual

Common Service Manual

2010 TRX420 TE/FE/FPE

Owner’s Manual

＊

Prices are subject to change without notice and without incurring obligation.

Price Each

＊

$48.00

$48.00

$16.00

224


０９／０５／１１１５：１６：３４３１ＨＰ４８３００２３４

Order On-Line: www.helminc.com

Order Toll Free: 1-888-CYCLE93

(1-888-292-5393)

(NOTE: For Credit Card Orders Only)

Monday − Friday 8:00 AM − 6:00 PM EST

OR

By completing this form you can order the materials desired. You can pay by check or money order, or charge to your credit card. Mail to

Helm, Inc. at the address shown on the back of this order form.

Publication

Item No.

Item Description Qty.

Price

Each

＊

Total

Price

＊

Prices are subject to change without notice and without incurring obligation.

Orders are mailed within 10 days. Please allow adequate time for delivery.

Sub Total

Purchaser’s Sales Tax

Mich. add 6 %

Calif. add 8.25 %

Handling Charge

Grand Total

$3.75


225

０９／０５／１１１５：１６：５１３１ＨＰ４８３００２３５

NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent.

S

H

I

P

T

O

Customer Name

Attention

Street address/P. O. BOX

City

Daytime Telephone Number

( )

State

Apartment Number

Zip Code

Check or money order enclosed payable to Helm Inc. U. S. funds only. Do not send cash.

P

A

Y

M

E

N

T

Check here if your billing address is different from the shipping address shown above.

VISA MasterCard Discover

Account Number

Security Code

Expiration: Mo. Yr.

−

Customer Signature Date

These Publications cannot be returned for credit without receiving advance authorization within 14 days of delivery. For returns, a restocking fee may be applied against the original order.

HELM

P. O. BOX 07280, DETROIT, MICHIGAN 48207

226


０９／０５／１１１５：１６：５９３１ＨＰ４８３００２３６

Warranty Coverage

Your new Honda is covered by these warranties:

TRX Limited Warranty

Emission Control System Warranty

There are responsibilities, restrictions, and exclusions which apply to these warranties. Please read the Warranties Booklet given to you by your Honda dealer at the time of purchase. Be sure to keep your Honda owner’s card with your Warranties Booklet.

It is important to realize that your warranty applies to defects in material or workmanship of your Honda. Your warranty coverage does not apply to normal wear or deterioration associated with using the ATV.

Your warranty coverage will not be voided if you choose to perform your own maintenance. However, you should have the proper tools and service information, and be mechanically qualified. Failures that occur due directly to improper maintenance are not covered.

Almost all of your warranty coverage can be extended through the

Honda Protection Plan. For more information, see your Honda dealer.


227

０９／０５／１１１５：１７：０５３１ＨＰ４８３００２３７

Warranty Service

Please remember that recommended maintenance interval servicing is not included in your warranty coverage. Additionally, your warranty does not apply to the normal wear of items (such as brakes, tires, etc.).

If you believe you have a problem with your ATV, call the service department of your Honda dealer. Make an appointment for an inspection and diagnosis. Remember, as the owner of the ATV, you will be asked to authorize that inspection. Your dealer will give you the results of the inspection. If the problem is covered under warranty, your dealer will perform the warranty repairs for you.

If you have questions about warranty coverage or the nature of the repair, it is best to talk to the Service Manager of your Honda dealer.

Sometimes, in spite of the best intentions of all concerned, a misunderstanding may occur. If you aren’t satisfied with your dealer’s handling of the situation, we suggest you discuss your problem with the appropriate member of the dealership’s management team. If the problem has already been reviewed with the Service Manager, Parts

Manager, Sales Manager, etc., contact the Owner of the dealership or their designated representative.

228


０９／０５／１１１５：１７：１４３１ＨＰ４８３００２３８

Contacting Honda

Your owner’s manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner’s manual can be answered by your Honda dealer. If your dealer doesn’t have the answer right away, they will get it for you.

If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That’s why it’s important to work to resolve any differences at the dealership level.

If you wish to comment on your experiences with your Honda or with your dealer, please send your comments to the following address:

Motorcycle Division, American Honda Motor Co., Inc., P.O. Box 2200,

Torrance, CA 90509-2200, mailstop: 100-4C-7B, telephone: (866) 784-

1870.

Please include the following information in your letter: name, address, and telephone number product model, year, and VIN date of purchase dealer name and address

We will likely ask your Honda dealer to respond, or possibly acknowledge your comments directly.


229

０９／０５／１１１５：１７：２１３１ＨＰ４８３００２３９

Your Honda Dealer

Once you purchase your new Honda, get familiar with the organization of your Honda dealer so you can utilize the full range of services available.

The service department is there to perform regular maintenance and unexpected repairs. It has the latest available service information from

Honda. The service department will also handle warranty inspections and repairs.

The parts department offers Honda Genuine Parts, Pro Honda products, and Honda Genuine Accessories. The same quality that went into your

Honda can be found in Honda Genuine replacement parts. You’ll also find comparable quality in the accessories and products available from the parts department.

The sales department offers the Honda Protection Plan to extend almost all of your warranty coverage.

Your Honda dealer can inform you about competition and other riding events in your area. You’ll also find that your dealer is a source of information about the Honda Rider’s Club of America.

We’re sure you’ll be as pleased with the service your Honda dealer continues to provide after the sale as you are with the quality and dependability of your Honda.

230


０９／０５／１１１５：１７：２５３１ＨＰ４８３００２４０

The Honda Rider’s Club

You may be eligible for a Honda Rider’s Club of America (HRCA) membership with the purchase of your new Honda. You can log on to the HRCA Clubhouse website for details at

www.hrca.honda.com.


231

０９／０５／１１１５：１７：３１３１ＨＰ４８３００２４１

Index

A

accessories ............................................................................................

. 50 age recommendation ............................................................................

. 41 air cleaner, dust cover .......................................................................................

. 128 filter ................................................................................................

. 124 housing drain tube ..........................................................................

. 129 air pressure, gauge ................................................................................................

. 99 tire ..................................................................................................

. 154

American Honda, contacting ..............................................................

. 229 apparel, protective ................................................................................

. 38 appearance care ..................................................................................

. 169 authorized manuals .............................................................................

. 224

B

bank angle sensor ignition cut-off system ............................................

. 62 battery .................................................................................................

. 164 brakelight switch adjustment ..............................................................

. 151 brakes, cables ..............................................................................................

. 150 draining water from ........................................................................

. 152 fluid ................................................................................................

. 142 front brake lever ...............................................................................

. 32 pad wear .........................................................................................

. 145 parking .............................................................................................

. 33

232

Index

０９／０５／１１１５：１７：３６３１ＨＰ４８３００２４２

Index

rear brake lever .................................................................................

. 32 rear brake lever freeplay ................................................................

. 148 rear brake pedal ................................................................................

. 32 rear brake pedal freeplay ................................................................

. 146 shoe wear ........................................................................................

. 150 braking .................................................................................................

. 70 break-in guidelines .............................................................................

. 215 button, hourmeter/odometer/tripmeter select ...............

. 14, 17, 20, 21, 22

C

capacity, fuel ......................................................................................

. 103 care, appearance .................................................................................

. 169 cargo, loading and operational guidelines ...................................................

. 49 weight limit ......................................................................................

. 48 cleaning, appearance care ...................................................................

. 169 climbing hills ........................................................................................

. 75 clip ......................................................................................................

. 101 clutch system ......................................................................................

. 132 color label ...........................................................................................

. 209 compartment, owner’s manual ................................................................................

. 99 tool kit ..............................................................................................

. 98 component fails ..................................................................................

. 206 consumer information ........................................................................

. 223 controls & features ...............................................................................

. 24 crash, if you ........................................................................................

. 203 crossing or turning on hills or slopes ....................................................

. 80 customer service .................................................................................

. 229

Index

233

０９／０５／１１１５：１７：４２３１ＨＰ４８３００２４３

Index

D

differential oil (Except TRX420TE) ..................................................

. 116 dimmer switch, headlight .....................................................................

. 28 dipstick ...............................................................................................

. 109 display check ........................................................................................

. 15 display, multi-function .........................................................................

. 18 drivetrain boots ...................................................................................

. 162

E

electric power steering (PS) .................................................................

. 36 emission control systems ....................................................................

. 216 engine, flooded .............................................................................................

. 62 guard ..............................................................................................

number ...........................................................................................

. 160

. 208 oil ...................................................................................................

. 105 pinging ...........................................................................................

. 102 starting ..............................................................................................

. 60 stop switch ........................................................................................

. 27 stopping ............................................................................................

. 64 won’t start ......................................................................................

. 186 environment .......................................................................................

exhaust system,

. 182 cleaning purging

............................................................................................

. 44

...........................................................................................

. 138

234

Index

０９／０５／１１１５：１７：４７３１ＨＰ４８３００２４４

Index

F

final gear case oil ...............................................................................

. 114 flag pole bracket ...................................................................................

. 34 flat tire ................................................................................................

. 192 flooded engine ......................................................................................

. 62 front boot guards (Except TRX420TE) .............................................

front driveshaft boots (Except TRX420TE) ......................................

. 161

. 163 front driveshaft guards (Except TRX420TE) ....................................

. 161 fuel, fill cap ............................................................................................

. 103 gauge ................................................................................................

. 23 oxygenated .....................................................................................

. 220 recommendation .............................................................................

. 102 refueling .........................................................................................

. 103 reserve fuel supply .........................................................................

. 103 tank capacity ..................................................................................

. 103 valve .................................................................................................

. 24 fuses ...................................................................................................

. 198

G

gap, spark plug ...................................................................................

. 135 gasohol ...............................................................................................

. 220 gasoline ..............................................................................................

. 102 gear case oil ........................................................................................

. 114 gear shifting .........................................................................................

. 65 gearshift switch ....................................................................................

. 65 guards .................................................................................................

. 160

Index

235

０９／０５／１１１５：１７：５２３１ＨＰ４８３００２４５

Index

H

headlight dimmer switch ......................................................................

. 28 headlight switch hills,

...................................................................................

. 28 crossing or turning on slopes ............................................................

. 80 riding down hills ..............................................................................

. 79 riding up hills ...................................................................................

. 75 stopping on hills ...............................................................................

. 77

Honda, contacting .......................................................................................

. 229 dealer ..............................................................................................

. 230

Rider’s Club hourmeter

...................................................................................

.................................................................................

. 231

. 17, 18, 22 hourmeter/odometer/tripmeter select button ................

. 14, 17, 20, 21, 22

Honda service manual ........................................................................

. 224

236

Index

０９／０５／１１１５：１７：５７３１ＨＰ４８３００２４６

Index

I

identification, vehicle .........................................................................

. 208 ignition switch ......................................................................................

. 25 indicators, gear position indicator ..........................................................

. 17, 18, 19 high coolant temperature indicator .....................................

. 14, 16, 196 neutral indicator .........................................................................

. 14, 16 oil change indicator ..............................................................

. 17, 18, 20

PGM-FI indicator .......................................................................

. 14, 16

PS (Electric Power Steering) indicator (TRX420FPE only) ...

. 14, 16, 36 reverse indicator .........................................................................

. 14, 16

4WD indicator (Except TRX420TE) ...................................

. 14, 16, 26 inspection, pre-ride ...............................................................................

. 43

Index

237

０９／０５／１１１５：１８：０２３１ＨＰ４８３００２４７

Index

K

key, lost ..................................................................................................

. 204 number ...........................................................................................

. 204 kit, tool .................................................................................................

. 98

L

labels, safety ...........................................................................................

. 5 lamp check ...........................................................................................

. 14 lever, 2WD/4WD select (Except TRX420TE) .....................................

. 26 limit, weight .........................................................................................

. 48 load limits .............................................................................................

. 48 loading guidelines ................................................................................

. 49 lubrication, differential oil (Except TRX420TE) ..............................................

. 116 engine oil ........................................................................................

. 105 gear case oil ....................................................................................

. 114

238

Index

０９／０５／１１１５：１８：０７３１ＨＰ４８３００２４８

Index

M

maintenance, component locations .........................................................................

. 95 importance ........................................................................................

. 87 precautions .......................................................................................

. 89 record ...............................................................................................

. 94 safety ................................................................................................

. 88 schedule ............................................................................................

. 90 manual, service ...................................................................................

. 224 maximum weight limit .........................................................................

. 48 modifications ........................................................................................

. 51 multi-function display ..........................................................................

. 18

Index

239

０９／０５／１１１５：１８：１２３１ＨＰ４８３００２４９

Index

N

neutral indicator .............................................................................

. 14, 16 noise emission control system ............................................................

. 219 numbers, serial ...................................................................................

. 208

O

obstacles, riding over ...........................................................................

. 82 odometer ...................................................................................

. 17, 18, 21 oil, differential (Except TRX420TE) ...................................................

. 116 engine .............................................................................................

. 105 gear case .........................................................................................

. 114 operation component locations .............................................................

. 11 owner’s manual storage ........................................................................

. 99 oxygenated fuels ................................................................................

. 220

240

Index

０９／０５／１１１５：１８：１９３１ＨＰ４８３００２５０

Index

P

parking .................................................................................................

. 84 passenger, no carrying ..........................................................................

. 41 pavement, no riding on .........................................................................

. 55 pinging, engine ...................................................................................

. 102 plug, spark ..........................................................................................

. 134 pre-ride inspection ................................................................................

. 43 problems, unexpected .........................................................................

. 183 propeller shaft boots & yoke joint boot ..............................................

. 162 protective apparel .................................................................................

. 38

PS (Electric Power Steering) (TRX420FPE only) ...............................

. 36

R

rear final gear case oil ........................................................................

. 114 removal, seat ......................................................................................

. 100 reverse, assist cable ......................................................................................

. 133 assist lever ......................................................................................

. 133 gear, shifting into .............................................................................

. 68 indicator .....................................................................................

. 14, 16 riding in ............................................................................................

. 68 selector knob ....................................................................................

. 31 rider training .........................................................................................

. 40

Rider’s Club, Honda ...........................................................................

. 231

(cont’d)

Index

241

０９／０５／１１１５：１８：２５３１ＨＰ４８３００２５１

Index

riding, basic operations ................................................................................

. 53 clothing .............................................................................................

. 38 precautions .......................................................................................

. 55 preparing for ..................................................................................

. 174 over obstacles ...................................................................................

. 82 safety ..................................................................................................

. 2 safety precautions .............................................................................

. 55 through water ...................................................................................

. 83

S

safety, important precautions .......................................................................

. 89 labels ..................................................................................................

. 5 riding precautions .............................................................................

. 55 schedule, maintenance ..........................................................................

. 90 seat removal .......................................................................................

. 100 select lever, 2WD/4WD (Except TRX420TE) .....................................

. 26 serial numbers ....................................................................................

. 208 service, customer .........................................................................................

. 229 manuals ..........................................................................................

. 224 warranty .........................................................................................

. 228

242

Index

０９／０５／１１１５：１８：２９３１ＨＰ４８３００２５２

Index

shifting gears ........................................................................................

. 65 skid plate ............................................................................................

. 160 skidding or sliding ................................................................................

. 74 spark arrester ......................................................................................

. 138 spark knock ........................................................................................

. 102 spark plug ...........................................................................................

. 134 specifications ......................................................................................

. 210 speedometer ...................................................................................

. 17, 18 stalling on a hill ....................................................................................

. 77 start button ............................................................................................

. 27 starting, engine ...............................................................................................

. 60 troubleshooting ...............................................................................

. 186 stop switch, engine ...............................................................................

. 27 stopping engine ....................................................................................

. 64 storage,

ATV ...............................................................................................

. 178 owner’s manual ................................................................................

. 99 suspension, adjustment (Except TRX420TE) ....................................................

. 139 spring pre-load (Except TRX420TE) .............................................

. 140 switch, downshift ...................................................................................

. 30, 65 engine stop .......................................................................................

. 27 headlight ...........................................................................................

. 28 headlight dimmer .............................................................................

. 28 ignition .............................................................................................

. 25 upshift ........................................................................................

. 30, 65

Index

243

０９／０５／１１１５：１８：３４３１ＨＰ４８３００２５３

Index

T

throttle, cable ...............................................................................................

. 131 lever ..................................................................................

. 29, 130, 131 tires, air pressure .....................................................................................

. 154 flat ..................................................................................................

. 192 replacing .........................................................................................

. 159 repairing .........................................................................................

. 158 thread conditions ....................................................................

. 156, 157 tool kit ..................................................................................................

. 98 trailer hitch ...........................................................................................

trailer towing,

. 35 operational guidelines ......................................................................

. 49 weight limits .....................................................................................

. 48 training, rider ........................................................................................

. 40 transporting your ATV .......................................................................

. 176 tripmeter ...................................................................................

. 17, 18, 21 trouble, unexpected ............................................................................

. 183 troubleshooting, starting .....................................................................

. 186 turning, on hills or slopes ...............................................................................

. 80 on level ground .................................................................................

. 72

244

Index

０９／０５／１１１５：１８：４０３１ＨＰ４８３００２５４

Index

V

valve, fuel .............................................................................................

. 24 valve clearance ...................................................................................

. 137 vehicle identification no. (VIN) .........................................................

. 208

W

warning labels ........................................................................................

. 5 warranty, coverage .........................................................................................

. 227 extended .........................................................................................

. 227 service ............................................................................................

. 228 washing your ATV .............................................................................

. 170 water, draining from brakes ......................................................................

. 152 riding through ...................................................................................

. 83 weight limit ..........................................................................................

. 48 wheel removal ....................................................................................

. 194

Index

245

０９／０５／１１１５：１８：４３３１ＨＰ４８３００２５５

246

Memo

０９／０５／１１１５：１８：４６３１ＨＰ４８３００２５６

Memo

247

０９／０５／１１１５：１８：４８３１ＨＰ４８３００２５７

248

Memo

０９／０５／１１１５：１８：５１３１ＨＰ４８３００２５８

Memo

249

０９／０５／１１１５：１８：５４３１ＨＰ４８３００２５９

250

Memo

０９／０５／１１１５：１９：０２３１ＨＰ４８３００２６０

Quick Reference

The following is a brief, but important collection of information you need to know about your Honda. You’ll also find space to record important notes.

How To Avoid Costly Repairs

The engine of your Honda can be the most expensive component to repair. Proper maintenance, especially the use of the recommended fluids and filters, prevents premature wear and damage.

Frequent causes of costly repairs are:

Engine oil –– insufficient quantity, improper oil.

Air cleaner –– dirty, leaking because of improper installation (poor seal).

Record important information on the following page:

Quick Reference

０９／０５／１１１５：１９：０７３１ＨＰ４８３００２６１

Quick Reference

Engine No.

VIN

Ignition Key No.

Color Label

Owner’s Name

Address

City/State

Phone

Dealer’s Name

Address

City/State

Phone

Service Mgr.

Quick Reference

０９／０５／１１１５：１９：１８３１ＨＰ４８３００２６２

Quick Reference

Scheduled

Maintenance

Pre-ride Inspection

Fuel/Capacity

Engine Oil

Maximum Weight

Capacity

Initial: 100 miles (150 km)

Regular: every 600 miles (1,000 km)

Check the following items each time before you ride (page 43 ): engine oil, radiator coolant, fuel, tires, drivetrain boots, guards, nuts & bolts, underbody & exhaust system, air cleaner housing drain tube, leaks, loose parts, cables, lights, throttle, brakes, reverse assist lever, switches, steering.

unleaded gasoline, pump octane number

86 or higher

3.51 US gal (13.3 ) reserve:

0.69 US gal (2.6 )

API Service Classification SG or higher except oils labeled as energy conserving on the circular API service label,

SAE 10W-30, JASO T 903 standard MA,

Pro Honda GN4 4-stroke oil or equivalent

485 lb (220 kg) rider, all cargo and accessories

Quick Reference

０９／０５／１１１５：１９：３３３１ＨＰ４８３００２６３

Tires

Tire Pressure (cold)

Spark Plugs

Coolant

Fuses

Quick Reference

Front: AT24 × 8-12

MAXXIS M977

★★

Rear: AT24 × 10-11

MAXXIS M978

★★

Front: 3.6 psi (25.0 kPa) …TRX420TE

4.4 psi (30.0 kPa) …TRX420FPE

3.6 psi (25.0 kPa)

TRX420FE

Rear: standard:

BKR5E-11 (NGK) or

K16PR-U11 (DENSO) ethylene glycol antifreeze (silicate-free) for aluminum engines in 50/50 solution with Pro Honda HP Coolant or an equivalent distilled water main: 30 A shift motor : 30 A other: 15 A, 10 A × 3

PS (Electric Power Steering)

(TRX420FPE only): 40 A

Quick Reference

０９／０５／１１１５：１９：５２３１ＨＰ４８３００２６４

Quick Reference

These symbols are used in Controls & Features section:

SYMBOL COMPONENT

ON − ignition switch

OFF − ignition switch

2WD/4WD select lever

4WD indicator − lights when the

4WD drive mode engages

START button

RUN − engine stop switch

OFF

− engine stop switch

ON

− headlight switch

OFF

− headlight switch

HI

− headlight dimmer switch

LO

− headlight dimmer switch upshift switch − gearshift switch downshift switch − gearshift switch reverse selector knob lock lever − parking brake

SEE PAGE

25

25

26

26

28

28

28

30

27

27

27

28

30

31

33

Quick Reference

０９／０５／１１１５：１９：５５３１ＨＰ４８３００２６５

０９／０５／１１１５：１９：５７３１ＨＰ４８３００２６６

No results