Honda SPORTRAX 300EX, TRX300EX, TRX300EX 2007 Owner's Manual

06/04/27 10:28:01 31HM3740_001

This manual should be considered a permanent part of the ATV and should remain with the ATV when it is resold.

This publication includes the latest production information available before printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation.

No part of this publication may be reproduced without written permission.

The vehicle pictured on the front cover may not match your vehicle.

Honda Motor Co., Ltd. 2006

06/04/27 10:28:05 31HM3740_002

2007

Honda TRX300EX

SPORTRAX 300EX

OWNER’S MANUAL

FOR OFF-ROAD USE ONLY

This vehicle is designed and manufactured for off-road use only.

USA only:

It conforms to US EPA Noise Emission regulations, but does not conform to Federal Motor Vehicle Safety Standards or US EPA On

Highway Exhaust Emission regulations, and operation on public streets, roads, or highways is illegal. The vehicle is equipped with a USDA qualified spark arrester. Obey local laws and regulations.

It conforms to US EPA and California exhaust emission regulations for

ATVs.

06/04/27 10:28:14 31HM3740_003

Introduction

Congratulations on choosing your Honda ATV.

When you own a Honda, you’re part of a worldwide family of satisfied customers − people who appreciate Honda’s reputation for building quality into every product.

Your Honda was designed as a recreational ATV for off-road use by one rider only.

Before riding, take time to get acquainted with your ATV and how it works. To protect your investment, we urge you to take responsibility for keeping your ATV well maintained. Scheduled service is a must, of course. But it’s just as important to observe the break-in guidelines, and perform all pre-ride and other periodic checks detailed in this manual.

We also recommend that you read this owner’s manual before you ride.

It’s full of facts, instructions, safety information, and helpful tips. To make it easy to use, the manual contains a detailed list of topics at the beginning of each section, and both an in-depth table of contents and an index at the back of the book.

As you read this manual, you will find information that is preceded by a symbol. This information is intended to help you avoid damage to your Honda, other property, or the environment.

Read the Warranties Booklet (page 199 ) thoroughly so you understand the coverages that protect your new Honda and are aware of your rights and responsibilities.

Whenever you ride, tread lightly. By staying on established trails and riding only in approved areas, you help protect the environment and keep off-road riding areas open for the future.

Introduction

06/04/27 10:28:19 31HM3740_004

Introduction

If you have any questions, or if you ever need special service or repairs, remember that your Honda dealer knows your ATV best and is dedicated to your complete satisfaction.

Please report any change of address or ownership to your Honda dealer so we will be able to contact you concerning important production information.

You may also want to visit our website at www.honda.com.

Happy riding!

California Proposition 65 Warning

WARNING: This product contains or emits chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

Introduction

06/04/27 10:28:23 31HM3740_005

A Few Words About Safety

Your safety, and the safety of others, is very important. And operating this ATV safely is an important responsibility.

To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.

This information alerts you to potential hazards that could hurt you or others.

Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining an ATV. You must use your own good judgment.

You will find important safety information in a variety of forms, including:

Safety Labels –– on the ATV.

Safety Messages –– preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION .


06/04/27 10:28:29 31HM3740_006


These signal words mean:

You WILL be KILLED or

SERIOUSLY HURT if you don’t follow instructions.

You CAN be KILLED or SERIOUSLY

HURT if you don’t follow instructions.

You CAN be HURT if you don’t follow instructions.

Safety Headings –– such as Important Safety Reminders or Important

Safety Precautions.

Safety Section –– such as ATV Safety.

Instructions –– how to use this ATV correctly and safely.

This entire manual is filled with important safety information –– please read it carefully.


06/04/27 10:28:37 31HM3740_007

Contents

These pages give an overview of the contents of your owner’s manual.

The first page of each section lists the topics covered in that section.

ATV Safety .......................................................................................

.

Important safety information you should know, plus a look at the safety-related labels on your ATV.

1

Indicators & Controls ......................................................................

.

The location and function of indicators and controls on your ATV and operating instructions for various controls and features.

9

Before Riding ....................................................................................

.

25

The importance of wearing a helmet and other protective gear, how to make sure you and your ATV are ready to ride, and important information about loading.

Basic Operation & Riding ...............................................................

.

How to start and stop the engine, shift gears, and brake. Also, riding precautions.

39

Contents

06/04/27 10:28:48 31HM3740_008

Contents

Servicing Your Honda .....................................................................

. 71

Why your ATV needs regular maintenance, what you need to know before servicing your Honda, an owner maintenance schedule, and instructions for specific maintenance and adjustment items.

Tips ....................................................................................................

.

153

How to store and transport your ATV and how to be an environmentally-responsible rider.

Taking Care of the Unexpected ......................................................

.

163

What to do if you have a flat tire, your engine won’t start, etc.

Technical Information .....................................................................

.

179

ID numbers, technical specifications, and other technical facts.

Consumer Information ....................................................................

.

195

Information on warranties, emission controls, how to get Honda service manuals.

Table of Contents .............................................................................

.

204

Sequential listing of topics in this owner’s manual.

Index ..................................................................................................

.

210

Quick Reference

Handy facts about fuel, engine oil, tire sizes, and air pressures.

Contents

06/04/27 10:28:49 31HM3740_009

06/04/27 10:28:53 31HM3740_010

ATV Safety

This section presents some of the most important information and recommendations to help you ride your ATV safely. Please take a few moments to read these pages. This section also includes information about the location of safety labels on your ATV.

Important Safety Information ................................................................

. 2

Safety Labels ..........................................................................................

. 5

ATV Safety

1

06/04/27 10:29:00 31HM3740_011

Important Safety Information

Your ATV can provide many years of service and pleasure − if you take responsibility for your own safety and understand the challenges you can meet while riding.

There is much that you can do to protect yourself when you ride. You’ll find many helpful recommendations throughout this manual. The following are a few that we consider most important.

Follow the Age Recommendation

The minimum recommended age for this ATV model is 16. Children under age 16 should never operate this vehicle.

Always Wear a Helmet

It’s a proven fact: helmets significantly reduce the number and severity of head injuries. So always wear an approved motorcycle helmet. We also recommend that you wear eye protection, sturdy boots, gloves, and other protective gear (page 26 ).

Never Carry a Passenger

Your ATV is designed for one person only. There are no handholds, footrests, or seat for a second person − so never carry a passenger. A passenger could interfere with your ability to move around to maintain your balance and control of the ATV.

2

ATV Safety

06/04/27 10:29:06 31HM3740_012


Ride Off-Road Only

Your ATV is designed and manufactured for off-road use only. The tires are not made for pavement, and the ATV does not have turn signals and other features required for use on public roads. If you need to cross a paved or public road, get off and walk your ATV across.

Take Time to Learn & Practice

Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.

Because many accidents involve inexperienced or untrained riders, we urge all riders to take a training course approved by the ATV Safety

Institute (ASI). See page 28 .

Contact an authorized ATV dealer or call 1-800-887-2887 (USA only) to find out about the training courses nearest you.

Be Alert for Off-Road Hazards

The terrain can present a variety of challenges when you ride off-road.

Continually ‘‘read’’ the terrain for unexpected turns, drop-offs, rocks, ruts, and other hazards. Always keep your speed low enough to allow time to see and react to hazards.

ATV Safety

3

06/04/27 10:29:12 31HM3740_013


Ride within Your Limits

Pushing limits is another major cause of ATV accidents. Never ride beyond your personal abilities or faster than conditions warrant.

Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgments and ride safely.

Don’t Drink and Ride

Alcohol and riding don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and ride, and don’t let your friends drink and ride either.

Keep Your Honda in Safe Condition

It’s important to keep your ATV properly maintained and in safe riding condition. Having a breakdown can be difficult, especially if you are stranded off-road far from your base. To help avoid problems, inspect your ATV before every ride and perform all recommended maintenance.

4

ATV Safety

06/04/27 10:29:16 31HM3740_014

Safety Labels

Your ATV comes with a hang tag and several labels containing important safety information. Anyone who rides the vehicle should read and understand this information before riding.

The labels should be considered permanent parts of the vehicle. If a label comes off or becomes hard to read, contact your Honda dealer for replacements.

ATV Safety

5

06/04/27 10:29:27 31HM3740_015

Safety Labels

USA only

6

ATV Safety

06/04/27 10:29:32 31HM3740_016

Safety Labels

ATV Safety

7

06/04/27 10:29:42 31HM3740_017

Safety Labels

8

ATV Safety

06/04/27 10:29:46 31HM3740_018

Indicators & Controls

This section shows the location of all indicators and controls you would normally use before or while riding your ATV.

The items listed on this page are described in this section. Instructions for other components are presented in other sections of this manual where they will be most useful.

Operation Component Locations .........................................................

. 11

Indicators ..............................................................................................

. 14

Reverse and Neutral Indicators ........................................................

. 14


9

06/04/27 10:29:50 31HM3740_019


Controls & Features .............................................................................

. 15

Fuel Valve ........................................................................................

. 15

Choke Lever .....................................................................................

. 16

Ignition Switch .................................................................................

. 17

Start Button ......................................................................................

. 18

Engine Stop Switch ..........................................................................

. 18

Headlight Switch ..............................................................................

. 19

Headlight Dimmer Switch ................................................................

. 19

Throttle Lever ..................................................................................

. 20

Clutch Lever/Parking Brake Lever ..................................................

. 20

Reverse Assist Lever ........................................................................

. 21

Front Brake Lever ............................................................................

. 22

Rear Brake Pedal ..............................................................................

. 22

Parking Brake ...................................................................................

. 23

Flag Pole Bracket .............................................................................

. 24

10


06/04/27 10:29:55 31HM3740_020

Operation Component Locations clutch lever/ parking brake lever parking brake lock lever parking brake pin front brake lever headlight switch ignition switch throttle lever headlight dimmer switch start button fuel fill cap engine stop switch reverse assist lever


11

06/04/27 10:29:58 31HM3740_021

Operation Component Locations rear brake pedal

12


06/04/27 10:30:02 31HM3740_022

Operation Component Locations fuel valve choke lever flag pole bracket shift lever seat lock lever


13

06/04/27 10:30:09 31HM3740_023

Indicators

Reverse and Neutral Indicators

handle cover.

The reverse indicator will light when the transmission is in reverse and the ignition switch is ON ( ).

The neutral indicator will light when the transmission is in neutral and the ignition switch is ON ( ).

If one of these indicators does not come on when it should, have your

Honda dealer check for burned-out bulbs or other problems.

CENTER OF HANDLEBAR

(2)

(1)

(1) reverse indicator

(2) neutral indicator

14


06/04/27 10:30:18 31HM3740_024

Controls & Features

Fuel Valve

LEFT SIDE

(1)

ON OFF RES

(1) fuel valve

The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor.

ON − normal position for riding.

OFF − for parking, storing, or transportation.

RES − for extra fuel to get to a gas supply for refueling.

Reserve Fuel

Remember to check that the fuel valve is in the ON position each time you refuel. If the fuel valve is left in the RES position, you may run out of fuel with no reserve.

For complete information about fueling your ATV, see page 87 .


15

06/04/27 10:30:24 31HM3740_025


Choke Lever

LEFT SIDE

(1)

( C )

( B )

( A )

(1) choke lever (A) fully OFF

(B) halfway position

(C) fully ON

1 46 .

16


06/04/27 10:30:33 31HM3740_026


Ignition Switch

(page 46 ). Insert the key and turn it to the right for the ON ( ) position.

Key Position

ON ( )

OFF ( )

Function

Electrical circuits on.

No electrical circuits function.

CENTER OF HANDLEBAR

OFF ON

(1)

(1) ignition switch ON

OFF


17

06/04/27 10:30:40 31HM3740_027


Start Button

LEFT HANDLEBAR

(1)

(1) start button

(2) engine stop switch

(2)

START

RUN

OFF starts the engine. See Starting Procedure, page 48 .

When the start button is pushed, the starter motor will crank the engine.

The starter motor will not operate if the engine stop switch is in the OFF

( ) position when the start button is pushed.

Engine Stop Switch

To operate, slide the switch to either OFF ( ) position. The switch must be in the RUN ( ) position to start the engine, and it should normally remain in the RUN ( ) position even when the engine is

OFF.

If your ATV is stopped with the ignition switch ON ( ) and the engine stop switch OFF ( ), the battery will discharge. Turn the ignition switch OFF ( ) to prevent battery discharge.

18


06/04/27 10:30:46 31HM3740_028


Headlight Switch

LEFT HANDLEBAR

(1)

(2)

(1) headlight switch

(2) headlight dimmer switch

ON

OFF

HI

LO

The headlight switch ( ) is used to turn the headlight ON ( ) or OFF

( ). To operate, turn the switch to ON ( ) or OFF ( ).

Headlight Dimmer Switch

and low beams of the headlight. To operate, turn the switch to HI ( ) for high beam, LO ( ) for low beam.


19

06/04/27 10:30:53 31HM3740_029


Throttle Lever

RIGHT HANDLEBAR

(A)

(1)

(1) throttle lever

(A) to open the throttle

The throttle controls engine rpm (speed). To increase engine rpm, press pressure on the throttle lever. The throttle will automatically return to the closed position (engine idle) when you remove your thumb.

Clutch Lever/Parking Brake Lever

The clutch lever/parking brake lever is used to disengage the clutch whenever you shift gears. To operate, pull the clutch lever/parking brake lever in all the way before shifting, then slowly release it after shifting.

See Clutch System, page 105 .

20


06/04/27 10:30:59 31HM3740_030


Reverse Assist Lever

tank, is used to shift into reverse. To operate, pull in the clutch lever/ on the clutch lever/parking brake lever, remove your right hand from throttle and turn the reverse assist lever. While turning the reverse assist gear). See Riding in Reverse page 54 .

LEFT HANDLEBAR RIGHT SIDE

(2)

(1)

LEFT SIDE

1st

Reverse

(1) reverse assist lever

(2) clutch lever/parking brake lever

(3) shift lever

(3)


21

06/04/27 10:31:04 31HM3740_031


Front Brake Lever

The front brake lever is used to slow or stop your ATV. To operate, pull the lever. For information on braking techniques, see page 56 .

Rear Brake Pedal

The rear brake pedal is used to slow or stop your ATV. To operate, depress the pedal. For information on braking techniques, see page 56 .

22


06/04/27 10:31:10 31HM3740_032


Parking Brake

LEFT HANDLEBAR

(1)

(A)

(2)

(3)

(1) lock lever

(2) parking brake pin

(3) clutch lever/ parking brake lever

(A) to lock down and hold the parking brake pin, squeeze the clutch lever/parking brake lever and then lock it with the lock lever. See Parking page 70 .

To release the parking brake, squeeze the clutch lever/parking brake lever.


23

06/04/27 10:31:15 31HM3740_033


Flag Pole Bracket

RIGHT REAR

(1)

(1) flag pole bracket

Flag poles are optional equipment available from your Honda dealer. To the flag pole kit.

Flag poles are required in some riding areas. Check local regulations before riding.

24


06/04/27 10:31:20 31HM3740_034

Before Riding

Before each ride, you need to make sure you and your Honda are both ready to ride. To help get you prepared, this section discusses how to evaluate your riding readiness, what items you should check on your

ATV, and adjustments to make for your comfort, convenience, or safety.

This section also includes important information about loading.

Are You Ready to Ride ?

.....................................................................

. 26

Protective Apparel ............................................................................

. 26

Rider Training ..................................................................................

. 28

Age Recommendation ......................................................................

. 29

No Passengers ..................................................................................

. 29

No Alcohol or Drugs ........................................................................

. 30

Is Your ATV Ready to Ride ?

..............................................................

. 31

Pre-ride Inspection ...........................................................................

. 31

Load Limits & Guidelines ....................................................................

. 34

Loading ............................................................................................

. 34

Load Limits ......................................................................................

. 35

Loading Guidelines ..........................................................................

. 36

Accessories & Modifications ...............................................................

. 37

Accessories .......................................................................................

. 37

Modifications ...................................................................................

. 38

Before Riding

25

06/04/27 10:31:29 31HM3740_035

Are You Ready to Ride?

Before you ride your ATV for the first time, we urge you to:

Read this owner’s manual and the labels on your ATV carefully.

Make sure you understand all the safety messages.

Know how to operate all the controls.

Before each ride, be sure:

You feel well and are in good physical and mental condition.

You are wearing an approved motorcycle helmet (with chin strap tightened securely), eye protection, and other protective clothing.

You don’t have any alcohol or drugs in your system.

Protective Apparel

For your safety, we strongly recommend that you always wear an approved motorcycle helmet, eye protection, boots, gloves, long pants, and a long-sleeved shirt or jacket whenever you ride.

Although complete protection is not possible, wearing proper gear can reduce the chance of injury when you ride.

Following are suggestions to help you choose the proper gear.

Helmets and Eye Protection

Your helmet is your most important piece of riding gear because it offers the best protection against head injuries. A helmet should fit your head comfortably and securely.

26

Before Riding

06/04/27 10:31:36 31HM3740_036


An open-face helmet offers some protection, but a full-face helmet offers more. Regardless of the style, look for a DOT (Department of

Transportation) sticker in any helmet you buy (USA only). Always wear a face shield or goggles to protect your eyes and help your vision.

Operating this ATV without wearing an approved motorcycle helmet, eye protection, and protective clothing could increase your chances of severe injury or death in the event of an accident.

Always wear an approved motorcycle helmet that fits properly and wear eye protection

(goggles or face shield), gloves, boots, long-sleeved shirt or jacket and long pants.

Additional Riding Gear

In addition to a helmet and eye protection, we also recommend:

Sturdy off-road motorcycle boots to help protect your feet, ankles, and lower legs.

Off-road motorcycle gloves to help protect your hands.

Riding pants with knee and hip pads, a riding jersey with padded elbows, and a chest/shoulder protector.

Before Riding

27

06/04/27 10:31:42 31HM3740_037


Rider Training

Developing your riding skills is an on-going process. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice riding the ATV in a safe area to build your skills. Do not ride in rough terrain until you get accustomed to the

ATV’s controls, and feel comfortable with its size and weight.

We urge all riders to take a certified course approved by the ATV Safety

Institute (ASI). For information about the ASI training course nearest you, call the national toll-free number; (800) 887-2887 (USA only).

Other riding tips can be found in the Tips & Practice Guide f or the ATV

Rider booklet that came with your ATV (USA only).

Operating this ATV without proper instruction could increase your risk of an accident which could lead to serious injury or death.

Beginning and inexperienced operators should complete the certified training course offered by

Honda. They should then regularly practice the skills learned in the course and the operating techniques described in the owner’s manual.

28

Before Riding

06/04/27 10:31:48 31HM3740_038


Age Recommendation

The minimum recommended age for this ATV model is 16. For safety, never let children under 16 years old operate this vehicle.

A child using an ATV that is not recommended for their age could lose vehicle control while riding, resulting in severe injury or death.

A child under 16 should never operate an ATV with engine size greater than 90cc.

No Passengers

This ATV is designed as an operator-only vehicle. The long seat is designed to allow the rider to change body position, not for carrying a passenger. Never let a passenger ride on the seat or on the front or rear cargo racks.

Carrying a passenger on this ATV greatly reduces your ability to balance and control this

ATV and could cause a crash and you or your passenger could be injured or killed.

Never carry a passenger on this ATV.

Before Riding

29

06/04/27 10:31:52 31HM3740_039


No Alcohol or Drugs

Alcohol, drugs and ATVs don’t mix. Even a small amount of alcohol can impair your ability to operate an ATV safely. Likewise, drugs − even if prescribed by a physician − can be dangerous while operating an

ATV. Consult your doctor to be sure it is safe to operate a vehicle after taking medication.

Operating this ATV after consuming alcohol or drugs can seriously affect your judgement, cause you to react more slowly, affect your balance and perception, and result in serious injury or death.

Never consume alcohol or drugs before or while operating this ATV.

30

Before Riding

06/04/27 10:32:00 31HM3740_040

Is Your ATV Ready to Ride?

Before each ride, it’s important to inspect your ATV and make sure any problem you find is corrected. A pre-ride inspection is a must, not only for safety, but because having a breakdown, or even a flat tire, can be a major inconvenience.

If your ATV has overturned or been involved in a collision, do not ride the vehicle until it has been inspected by your Honda dealer. There may be damage or other problems you cannot see.

Improperly maintaining this ATV or failing to correct a problem before riding can cause a crash in which you can be seriously hurt or killed.

Always perform a pre-ride inspection before every ride and correct any problems.

Pre-ride Inspection

Check the following items before you get on the ATV:

Engine Oil Check the level and add oil if needed (page

95 ).

Check for leaks.

Fuel Check the level and add fuel (page 88 ) if needed. Also make sure the fuel fill cap is securely fastened.

Check for leaks.

(cont’d)

Before Riding

31

06/04/27 10:32:12 31HM3740_041


Tires

Drive Chain

Nuts & Bolts

Underbody &

Exhaust System

Air Cleaner Housing

Drain Tube

Leaks, Loose Parts

Cable

Lights

Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damage or excessive wear (page 128 ).

Check the condition and slack. Adjust and lubricate if needed. Also check the chain slider for wear and replace if needed (page 136 ).

Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight.

Check for, and remove, any dirt, vegetation or other debris that could be a fire hazard or interfere with the proper operation of the vehicle.

Check for deposits in the drain tube. If necessary, clean the tube (page 102 ) and check the air cleaner case.

Walk around your ATV and look for anything that appears unusual, such as a leak or loose cable.

Check the cable housings for wear. Check the fittings for looseness. Replace or tighten as needed.

Make sure the headlight, brakelight and taillight are working properly.

32

Before Riding

06/04/27 10:32:23 31HM3740_042


Check these items after you get on the ATV:

Throttle Check the freeplay and adjust if needed. Press the throttle to make sure it moves smoothly without sticking, and snaps shut automatically when it is released, in all steering positions

(page 103 ).

Brakes

Clutch Lever/Parking

Brake Lever

Check for smooth operation and adjust if needed (page 105 ).

Reverse Assist Lever

Squeeze the front brake lever and step on the rear brake pedal to check that the controls operate normally. Make sure there is no brake fluid leakeage (page 120 ).

Check the freeplay and adjust if needed (page

109 ). Make sure the lever operates smoothly without sticking.

Check for proper function (page 19 ).

Headlight and

Headlight Dimmer

Switch

Engine Stop Switch

Steering

Check for proper function (page 18 ).

Check that the wheels turn properly as you steer the handlebar. Move the handlebar right and left and check that there is no excessive backlash.

Remember, be sure to take care of any problem you find, or have your

Honda dealer correct it before you ride.

Before Riding

33

06/04/27 10:32:29 31HM3740_043

Load Limits & Guidelines

Your Honda was designed as a rider-only ATV. It was not designed to carry a passenger or cargo. A passenger or cargo could interfere with your ability to move around to maintain your balance and control of the

ATV.

In addition, exceeding the weight limits or carrying an unbalanced load can seriously affect your ATV’s handling, braking and stability. Adding accessories or making modifications that change this ATV’s design and performance can also make it unsafe. Also, the weight of any accessories will reduce the maximum load the ATV can carry.

More specific information on load limits, accessories, and modifications follows.

Loading

How much weight you put on your ATV, and how you load it, are important to your safety. If you decide to carry cargo, you should be aware of the following information.

Overloading, improper loading, or carrying a passenger can cause a crash and you can be seriously hurt or killed.

Follow all load limits and other loading guidelines in this manual.

34

Before Riding

06/04/27 10:32:35 31HM3740_044


Load Limits

Following are the load limits for your ATV:

There are limits to how much weight can be carried on your ATV.

The following load limits apply to standard equipment only. Modifying your ATV, using non-standard equipment, or riding on terrain that is not flat and smooth could further reduce these limits.

maximum weight capacity 270 lbs (120 kg)

(includes the weight of the rider, all cargo, and accessories.)

The weight of added accessories will reduce the maximum cargo weight you can carry.

Before Riding

35

06/04/27 10:32:44 31HM3740_045


Loading Guidelines

As discussed on page 34 , we recommend that you do not carry any cargo on this ATV. However, if you decide to carry cargo, ride at reduced speeds and follow these common-sense guidelines.

Carrying cargo or pulling a trailer will affect how your ATV handles and greatly reduce its ability in accelerating, braking and making turns and other maneuvers.

Be sure to observe the weight limits and follow these guidelines:

Check that the tires are properly inflated.

Never ride with a passenger. The ATV is not designed to carry a passenger.

Do not tow another vehicle.

Never exceed the maximum weight limit.

Make sure all cargo is secured before riding.

Allow extra room for starting, stopping and turning whenever you carry cargo or pull a trailer.

Avoid riding on steep slopes when carrying cargo or pulling a trailer.

Never cross a slope when towing a trailer.

36

Before Riding

06/04/27 10:32:51 31HM3740_046

Accessories & Modifications

Modifying your ATV or using non-Honda accessories can make your

ATV unsafe.

Before you consider making any modifications or adding an accessory, be sure to read the following information.

Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding accessories and modifications.

Accessories

We strongly recommend that you use only genuine Honda accessories that have been specifically designed and tested for your ATV. Because

Honda cannot test all other accessories, you must be personally responsible for proper selection, installation, and use of non-Honda accessories.

Check with your Honda dealer for assistance and always follow these guidelines:

Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls.

Make sure the accessory does not interfere with your ability to shift body position on the seat or operate hand and foot controls.

Do not add any electrical equipment that will exceed the vehicle’s electrical system capacity (page 184 ). A blown fuse can cause a loss of lights or engine power (page 172 ).

Before Riding

37

06/04/27 10:32:56 31HM3740_047

Accessories & Modifications

Modifications

We strongly advise you not to remove any original equipment or modify your ATV in any way that would change its design or operation. Such changes could seriously impair your ATV’s handling, stability, and braking, making it unsafe to ride.

We also advise you not to make any modifications or remove any equipment (such as the USDA qualified spark arrester or emission control system components) that would make your ATV illegal in your area.

Removing or modifying your lights, exhaust system, emission control system, or other equipment can also make your ATV illegal.

38

Before Riding

06/04/27 10:33:01 31HM3740_048

Basic Operation & Riding

This section gives basic riding instructions, including how to start and stop your engine, and how to use the throttle and brakes. and what to do when you’re through riding.

To protect your new engine and enjoy optimum performance and service life, refer to Break-in Guidelines (page 186 ).

For information about carburetor adjustment for riding at high altitude, see page 187 .

Safe Riding Precautions .......................................................................

. 41

Off-Road Use Only ..........................................................................

. 41

Keep Hands and Feet on Controls ....................................................

. 42

Control Speed ...................................................................................

. 43

Use Care on Unfamiliar or Rough Terrain .......................................

. 44

Do Not Perform Stunts .....................................................................

. 45

Starting & Stopping the Engine ...........................................................

. 46

Preparation .......................................................................................

. 47

Starting Procedure ............................................................................

. 48

Flooded Engine ................................................................................

. 51

How to Stop the Engine ...................................................................

. 51

Shifting Gears ......................................................................................

. 52

Riding in Reverse .................................................................................

. 54

(cont’d)


39

06/04/27 10:33:04 31HM3740_049


Braking .................................................................................................

. 56

Riding Your ATV ................................................................................

. 58

Making Turns ...................................................................................

. 58

Skidding or Sliding ..........................................................................

. 60

Riding Up Hills ................................................................................

. 61

Riding Down Hills ...........................................................................

. 65

Crossing or Turning on Hills or Slopes ............................................

. 66

Riding Over Obstacles .....................................................................

. 68

Riding Through Water .....................................................................

. 69

Parking .................................................................................................

. 70

40


06/04/27 10:33:11 31HM3740_050

Safe Riding Precautions

Before riding your ATV for the first time, please review the ATV Saf ety section beginning on page 1, and the Bef ore Riding on page 25 .

section beginning

Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight.

Off-Road Use Only

Your ATV and its tires are designed and manufactured for off-road use only, not for pavement. Riding on pavement can affect handling and control. You should not ride your ATV on pavement.

Operating this ATV on paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of control.

Never operate the ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets.

When riding off-road, also remember to always obey local off-road riding laws and regulations. Obtain permission to ride on private property. Avoid posted areas and obey ‘‘no trespassing’’ signs.

(cont’d)


41

06/04/27 10:33:16 31HM3740_051


You should never ride your ATV on public streets, roads or highways, even if they are not paved. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. In many states it is illegal to operate ATVs on public streets, roads and highways.

Operating this ATV on public streets, roads or highways could cause you to collide with another vehicle.

Never operate this ATV on any public street, road or highway, even a dirt or gravel one.

Keep Hands and Feet on Controls

Always keep both hands on the handlebars and both feet on the footpegs when riding your ATV. This is important to maintain your balance and to control the vehicle. Removing even one hand from the handlebars or one foot from the footpegs can reduce your ability to control the ATV or could cause you to lose your balance and fall off the ATV.

Removing hands from handlebars or feet from footpegs during operation can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV.

Always keep both hands on the handlebars and both feet on the footpegs of your ATV during operation.

42


06/04/27 10:33:21 31HM3740_052


Control Speed

Riding at excessive speed increases the chance of an accident. In choosing a proper speed, you need to consider the capability of your vehicle, the terrain, visibility and other operating conditions, plus your own skills and experience.

Operating this ATV at excessive speeds increases your chances of losing control of the

ATV, which can result in an accident.

Always go at a speed that is proper for your vehicle, the terrain, visibility and other operating conditions, and your experience.


43

06/04/27 10:33:26 31HM3740_053


Use Care on Unfamiliar or Rough Terrain

Before riding in a new area, always check the terrain thoroughly. Don’t ride fast on unfamiliar terrain or when visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or holes in time to react.)

Failure to use extra care when operating this

ATV on unfamiliar terrain could result in the ATV overturning or going out of control.

Go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating the

ATV.

44


06/04/27 10:33:31 31HM3740_054


Never ride past the limit of visibility. Maintain a safe distance between your ATV and other off-road vehicles. Always exercise caution, and use extra care on rough, slippery and loose terrain.

Failure to use extra care when operating on excessively rough, slippery or loose terrain could cause loss of traction or vehicle control, which could result in an accident, including an overturn.

Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control the ATV on such terrain. Always be especially cautious on these kinds of terrain.

Do Not Perform Stunts

You should always operate your ATV in a safe and reasonable manner.

When riding, always keep all four wheels on the ground.

Attempting wheelies, jumps, and other stunts increases the chance of an accident, including an overturn.

Never attempt stunts, such as wheelies or jumps. Don’t try to show off.


45

06/04/27 10:33:36 31HM3740_055

Starting & Stopping the Engine

Always follow the proper starting procedure described below.

For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your ATV’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death.

Your ATV is equipped with a gear position starter cut-off system. The engine cannot be started if the transmission is in a forward gear − unless the clutch lever/parking brake lever is pulled in. The engine cannot be started if the transmission is in reverse gear.

46


06/04/27 10:33:46 31HM3740_056


Preparation

ON

(1) (2)

(3)

(1) fuel valve

(2) ignition switch

(4)

(3) neutral indicator

(4) engine stop switch

1.

Before starting, select a level surface and lock the parking brake

(page 23 ).

2.

2 ).

Confirm the following:

The engine stop switch ( ) is set to RUN ( ).


47

06/04/27 10:33:55 31HM3740_057


Starting Procedure

The carburetor is equipped with an accelerator pump. Do not open the throttle when starting the engine. This will flood the engine with excess fuel, resulting in hard starting.

To restart a warm engine, follow the procedure for

Temperature.’’

‘‘High Air

The starter motor will operate only when the transmission is in neutral.

Normal Air Temperature 10° − 35°C (50° − 95°F)

LEFT SIDE

(1)

( C )

( B )

( A )

(1) choke lever (A) fully OFF

(B) halfway position

(C) fully ON

1.

2.

is cold.

With the throttle slightly open, press the start button.

Pressing the electric start button for more than 5 seconds at a time may cause the starter to overheat and damage the starter. Release the start button for approximately 10 seconds before pressing it again.

48


06/04/27 10:34:03 31HM3740_058


3.

Immediately after the engine starts, push the choke lever down to the

4.

5.

Warm up the engine by opening and closing the throttle slightly.

After the engine has warmed up, push the choke lever down all the

6.

High Air Temperature 35°C (95°F) or above

LEFT HANDLEBAR

(1)

(1) start button

1.

Do not use the choke.

2.

3.

4.


If idling is unstable, open the throttle slightly.


49

06/04/27 10:34:11 31HM3740_059


Low Air Temperature 10°C (50°F) or below

For temperature below − 15 °C (5 °F), operate the starter button after opening and closing the throttle lever several times.

1.

2.

Follow steps 1 − 2 under ‘‘Normal Air Temperature.’’


3.

About a half minute after the engine starts, push the choke lever down

4.

After the engine has warmed up, push the choke lever down all the

5.

If idling is unstable, open the throttle slightly.

Extended use of the choke may impair piston and cylinder wall lubrication and shorten the lif e of the engine.

Do not race the engine during the warm-up period.

Racing a cold engine wastes fuel and increases engine wear.

50


06/04/27 10:34:22 31HM3740_060


Flooded Engine

If the engine fails to start after repeated attempts, it may be flooded with excess fuel. To clear a flooded engine:

1.

2.

Leave the engine stop switch set to RUN ( ).

Move the choke lever to the fully OFF position.

3.

Open the throttle fully.

4.

5.

Press the start button for 5 seconds.

If the engine starts, quickly close the throttle, then, if idling is unstable, open it slightly.

If the engine does not start, wait 10 seconds, then follow the High Air

Temperature procedure (page 49 ).

If the engine still won’t start, refer to If Your Engine Quits or Won’t

Start, page 166 .

How to Stop the Engine

Normal Engine Stop

To stop the engine, make sure the transmission is in neutral by checking that the neutral indicator lights, and turn the ignition switch OFF ( ).

The engine stop switch should normally remain in the RUN ( ) position even when the engine is OFF.

If your ATV is stopped with the engine stop switch OFF ( ) and the ignition switch ON ( ), the battery will discharge.

Emergency Engine Stop

To stop the engine in an emergency, use the engine stop switch. To operate, move the switch to either OFF ( ) position.


51

06/04/27 10:34:30 31HM3740_061

Shifting Gears

GEAR SHIFTING SEQUENCE

The shift lever is located near the left footpeg. One full stroke of the shift lever shifts the transmission to the next higher or lower gear in the shifting sequence. The shift lever automatically returns to the horizontal position when released.

Your ATV has five forward gears (1, 2, 3, 4 and 5). To shift the transmission, pull in the clutch lever, then operate the shift lever as follows.

To upshift to a higher gear, put the toe of your boot under the shift lever and raise it one full stroke. To downshift, step on the shift lever and depress it one full stroke.

To select reverse, use the reverse assist lever (page 54 ).

After starting the engine and letting it warm up, follow these procedures:

1.

With the transmission in neutral, depress and hold down the rear brake pedal. Release the clutch lever/parking brake lever (page 23 ).

52


06/04/27 10:34:39 31HM3740_062

Shifting Gears

2.

While the engine is idling, pull in the clutch lever/parking brake lever and depress the shift lever to shift into 1st gear.

3.

Release the brake pedal, gradually release the clutch lever/parking brake lever, and increase engine speed by gradually opening the

4.

throttle.

When the speed increases, close the throttle, pull in the clutch lever/

5.

parking brake lever, shift to 2nd gear by raising the shift lever, and gradually release the clutch lever/parking brake lever while gradually opening the throttle.

Repeat this sequence to progressively upshift to 3rd, 4th and 5th (top) gear.

6.

To downshift, reverse this sequence. Remember to close the throttle each time you shift to the next lower gear.

Learning when to shift gears comes with experience. Keep the following tips in mind:

As a general rule, shift while moving in a straight line.

Close the throttle and pull the clutch lever/parking brake lever in completely before shifting. Improper shifting may damage the engine, transmission, and drive train.

Upshift to a higher gear or reduce throttle before engine rpm (speed) gets too high. Learn the relationship between engine sound and the normal shifting points.

Downshift to a lower gear before you feel the engine laboring

(lugging) at low rpm.

Avoid downshifting to help slow your ATV when engine rpm is high.

Downshifting when engine speed is near its allowable maximum may over-rev the engine and cause possible damage.

To prevent transmission damage, do not coast or tow the ATV for long distances with the engine off.

Recommended Shift Points

Ride in the highest gear that lets the engine run and accelerate smoothly.

This will give you good fuel economy and effective emissions control.


53

06/04/27 10:34:48 31HM3740_063

Riding in Reverse

If you need to ride in reverse, make sure the area behind you is clear and only operate the ATV at low speed.

Improperly operating in reverse could cause you to hit an obstacle or person behind you, resulting in serious injury.

Make sure there are no obstacles or people behind you before selecting reverse gear. When it is safe to proceed, go slowly.

1.

Bring the vehicle to a complete stop, pull in the clutch lever/parking

2.

Be sure there are no obstacles or people in the way.

3.

4.

Depress and hold down the rear brake pedal.

Leaving your left hand on the clutch lever/parking brake lever, remove your right hand from the throttle and place it on the reverse

LEFT HANDLEBAR

(1)

LEFT SIDE

1st


Reverse

(2) shift lever

(2)

54


06/04/27 10:34:58 31HM3740_064

Riding in Reverse

5.

While turning the reverse assist lever, depress the shift lever to reach the reverse gear (below 1st gear). Make sure that the reverse indicator

6.

7.

8.

Remove your right hand from the reverse assist lever.

Release the rear brake pedal.

Slowly release the clutch lever/parking brake lever and open the throttle gradually to begin reverse operation.

RIGHT SIDE CENTER OF HANDLEBAR

(4)

(3)

(3) reverse assist lever (4) reverse indicator

9.

10.

Ride slowly. Do not open the throttle suddenly or make abrupt turns.

To stop, pull in the clutch lever/parking brake lever, close the throttle and gradually apply both the front and rear brakes. Do not abruptly apply the rear brake by itself.

11.

To shift out of reverse into 1st gear, pull in the clutch lever/parking brake lever and raise the shift lever one click to 1st gear. Make sure that the reverse indicator goes off.

Applying only the rear brake abruptly when operating in reverse gear could cause the front wheels to lift off the ground and the ATV could overturn backwards.

Carefully apply both the front and rear brakes when stopping in reverse gear.


55

06/04/27 10:35:05 31HM3740_065

Braking

Your ATV is equipped with disc braking systems which are hydraulically activated. Depressing the brake pedal applies the rear disc brake. Operating the brake lever applies the two front disc brakes.

As a general rule, the front braking system provides about 70 percent of total stopping power.

For full braking effectiveness, use both the pedal and lever simultaneously. Using both braking systems will stop your ATV faster with greater stability.

To slow or stop, apply the brake lever and brake pedal smoothly, while downshifting to match your speed.

Gradually increase braking as you feel the brakes slowing your speed.

The increase in engine compression from downshifting will help slow your ATV.

For maximum braking, close the throttle and firmly apply the brake lever and pedal controls.

Applying the brakes too hard may cause the wheels to lock and slide, reducing control of your ATV. If this happens, release the brake controls, steer straight ahead until you regain control, then reapply the brakes more gently.

When possible, reduce your speed or complete braking before entering a turn. Avoid braking or closing the throttle quickly while turning. Either action may cause one or more wheels to slip and reduce your control of your ATV.

56


06/04/27 10:35:11 31HM3740_066

Braking

Your ability to brake in a turn and to brake hard in an emergency situation are important riding skills.

When descending a long, steep grade, use engine compression braking by downshifting, with intermittent use of both brakes. Continuous brake application can overheat the brakes and reduce their effectiveness.

To prevent stalling the engine, pull the clutch lever/parking brake lever in before coming to a complete stop.

Riding with your foot resting on the brake pedal or your hand on the brake lever may overheat the brakes, reducing effectiveness.

For information on how to apply the brakes in various riding situations, see the following section, Riding Your ATV .


57

06/04/27 10:35:16 31HM3740_067

Riding Your ATV

Making Turns

Learn how to turn your ATV properly. Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns.

Turning improperly can make the ATV go out of control, causing a collision or overturn.

Always follow proper procedures for turning as described in this owner’s manual.

Practice turning at low speeds before attempting to turn at faster speeds.

Do not turn at excessive speeds.

58


06/04/27 10:35:21 31HM3740_068

Riding Your ATV

Lean your body to the inside of a turn and forward.

To make a turn on level ground: Steer the handlebar and lean your body toward the inside of the turn. Leaning helps balance the vehicle, and it feels more comfortable. Leaning into a turn is an important technique to master in riding an ATV.

To make a sharp turn at low speed: It helps to shift your body slightly forward on the seat, and lean inside, as you steer the handlebar. Shifting weight forward allows the rear wheels to turn easier, and it also improves front-wheel steering.

To make a turn from a full stop: Apply the throttle gradually when you turn and start up at the same time. Remember to shift your body forward to make sharp low-speed turns and whenever you turn while accelerating from a full stop.


59

06/04/27 10:35:26 31HM3740_069

Riding Your ATV

Skidding or Sliding

The terrain surface can be a major factor affecting turns. Skidding during a turn is more likely to occur on slippery surfaces, such as snow, ice, mud and loose gravel. If you skid on ice, you may lose all directional control. To avoid skidding on slippery terrain, keep your speed low and ride with caution.

Skidding or sliding improperly may cause you to lose control of this ATV. You may also regain traction unexpectedly, which may cause the

ATV to overturn.

Learn to safely control skidding by practicing at low speeds and on level, smooth terrain.

If your ATV skids sideways during a turn, steer in the direction of the skid. Avoid hard braking or accelerating until you have regained directional control.

60


06/04/27 10:35:32 31HM3740_070

Riding Your ATV

Riding Up Hills

The ATV’s ability to safely climb hills largely depends on the rider’s skill and judgment. Begin by practicing on smooth, gentle slopes. As you gain experience, you’ll learn the hazards and your own limitations.

You may then proceed to ride on more difficult terrain. However, you must be able to decide which hills or hazards might cause the ATV to overturn. Avoid excessively steep hills.

Operating on excessively steep hills can cause the vehicle to overturn more easily than operating on level surfaces or small hills.

Never operate the ATV on hills too steep for the

ATV or for your abilities.

When climbing hills, you must shift weight toward the front wheels to help keep them on the ground. To do this, shift your body slightly forward on the seat and lean forward. For greater weight shift, move your body farther forward and lean forward.

Climbing hills improperly could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for climbing hills as described in this owner’s manual.


61

06/04/27 10:35:38 31HM3740_071

Riding Your ATV

Shift weight forward when climbing hills.

Always check the terrain carefully before you start up any hill.

Never climb hills with excessively slippery or loose surfaces.

To climb a hill, take a running start in an appropriate gear and speed for the conditions. Maintain a steady speed as you ascend the hill.

Never open the throttle suddenly or make sudden gear changes. The

ATV could flip over backward.

Never go over the top of any hill at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill.

62


06/04/27 10:35:47 31HM3740_072

Riding Your ATV

Stalling the ATV and/or Rolling Backwards:

If you incorrectly estimate climbing capability or terrain conditions, the

ATV may not have enough power or traction to continue uphill. If this happen, the ATV can stall and/or roll backwards.

Stalling, rolling backwards or improperly dismounting while climbing a hill could result in the ATV overturning.

Always follow proper procedures for climbing a hill as described in this owner’s manual.

What to do if the ATV stalls or rolls backwards when climbing a hill:

If you are about to lose all forward speed:

1.

Using the front and rear brakes together, bring the ATV to a stop with the vehicle pointed straight uphill.

2.

3.

Get off the ATV while you continue holding the brakes.

Shift into neutral, set the parking brake and turn the engine off.

4.

Then assess the situation.

If the ATV starts rolling backwards before you begin braking:

1.

Keep your weight uphill.

2.

Carefully apply the front brakes first, then carefully apply the rear brake. Do not apply the rear brake only or abruptly if you are rolling backwards, or the vehicle may overturn.

If the ATV continues sliding backwards:

After you’ve applied the brakes, get off and away from the vehicle.


63

06/04/27 10:35:55 31HM3740_073

Riding Your ATV

What to do after the ATV has stalled or rolled backwards:

If the hill is too steep or too slippery, or if you have any doubt whether you can safely walk the ATV back down the hill, leave the vehicle where it is and get help. If possible, block the wheels so the vehicle doesn’t roll backwards.

If the hill is not too steep and you have good footing, you may be able to walk the ATV back down the hill. Make sure your intended path is clear in case you lose control of the ATV.

Be sure your legs are clear of the wheels.

Body position for backing down a hill.

1.

Stand with your body facing downhill, beside the vehicle so you can

2.

reach the front brake lever with your left hand.

Be sure your legs are clear of the wheels.

3.

Check your footing.

Slowly and carefully back the ATV down the hill using the front

4.

brake lever to control speed.

If you lose control of the ATV, for your safety, get away from the vehicle.

64


06/04/27 10:36:01 31HM3740_074

Riding Your ATV

Riding Down Hills

It’s usually advisable to descend hills with the ATV pointed straight downhill. Avoid angles that would cause the vehicle to lean sharply to one side.

Going down a hill improperly could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for going down hills as described in this owner’s manual.

On downhills, shift your weight back.

As you approach a downhill, stop and survey the terrain below. Never ride past the limit of your visibility. Never go down a hill at high speed.


65

06/04/27 10:36:08 31HM3740_075

Riding Your ATV

When you’ve selected a safe downhill path, shift into a lower gear, shift your weight back with your arms extended and braced against the handlebar, then go down slowly with the throttle closed.

Use mainly the rear brake to control speed. Avoid using either the front brake or rear brake hard or abruptly when riding down hills.

Remember, braking effectiveness is reduced on any hill with a loose surface.

Crossing or Turning on Hills or Slopes

Riding on hills or slopes is different from riding on level terrain. Be careful when riding on any hill. Make sure that you practice on gentle, smooth slopes before attempting to ride on steeper or more difficult terrain.

Improperly crossing hills or turning on hills could cause loss of control or cause the ATV to overturn.

Always follow proper procedures for crossing or turning on slopes as described in this Owner’s

Manual. Avoid crossing steep hills if possible.

66


06/04/27 10:36:16 31HM3740_076

Riding Your ATV

Crossing Hills or Slopes

To maintain balance and stability when riding across a slope, you need to shift weight toward the uphill side of the vehicle. To do this, move your body off the center of the seat and lean toward the uphill side.

On a slippery or loose surface, you may also need to steer slightly uphill to maintain a straight course across the slope.

Avoid crossing hills that are excessively steep, slippery or rough.

Shift weight uphill when crossing slopes.

Making Turns on Slopes

Compared to riding on level ground, you may need to shift more weight and lean more when making turns on slopes.

Do not make turns on any slopes until you have first mastered the techniques for making turns on level terrain.


67

06/04/27 10:36:20 31HM3740_077

Riding Your ATV

Riding Over Obstacles

Before operating in a new area, check for obstacles. Watch out for bumps, rain ruts, potholes and other obstacles in the terrain. When you approach any obstacle, reduce your speed and be prepared to stop.

Never try to ride over large obstacles, such as large rocks or fallen logs.

Improperly operating over obstacles could cause loss of control or a collision and could cause the ATV to overturn.

When you go over obstacles, always follow proper procedures as described in this owner’s manual.

68


06/04/27 10:36:28 31HM3740_078

Riding Your ATV

Riding Through Water

Your ATV is designed to travel through water up to approximately

10 inches (254 mm) deep. Before crossing a stream, make sure the water is not too deep or flowing too fast.

The ATV tires have some ability to float.

Operating this ATV through deep or fast-flowing water may cause a loss of traction and loss of control, which could lead to an accident.

Never operate this ATV in fast-flowing water or in water deeper than that specified in this

Owner’s Manual.

1.

Choose a path where both banks have gradual slopes.

2.

3.

Proceed through the water at a slow, steady speed.

Watch out for submerged obstacles and slippery rocks.

4.

5.

Avoid getting the spark plug or air cleaner wet, as this would cause the engine to stop.

After leaving the water, always test both the front and rear brakes.

Riding through water can make the brakes less effective than normal, and may reduce stopping ability.

If necessary, apply the brakes repeatedly until they dry out and operate normally.


69

06/04/27 10:36:38 31HM3740_079

Parking

1.

2.

Look for level parking area. Make sure the ground surface is firm.

After bringing your ATV to a stop, hold the brakes while you shift into neutral.

Set the parking brake.

3.

4.

5.

Turn the ignition switch OFF ( ).

If you’re through riding for the day, turn the fuel valve OFF.

If it is necessary to start the engine when your ATV is stopped on a grade in gear, rock the vehicle back and forth to allow shifting the transmission into neutral.

Parking on a Steep Incline or a Loose or Slippery Surface

If you must park your ATV on a steep incline or loose or slippery surface, use the following procedure:

1.

2.

3.

While holding the brakes, set the parking brake.

Turn the ignition switch OFF ( ) and release the brakes.

If the ATV begins to move, either while sitting on it or after you dismount, find a better parking location.

4.

If rocks or other objects are available, you can block the wheels as shown for additional security.

70


06/04/27 10:36:46 31HM3740_080

Servicing Your Honda

To help keep your ATV in good shape, this section includes a

Maintenance Schedule for required service and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on fuels and oils, and tips for keeping your

Honda looking good.

For information about replacing a fuse, see page 172 .

For information about the exhaust emission and noise requirements of the U.S. Environmental Protection Agency (EPA) and the California Air

Resources Board (CARB), see page 188 .

USA Only

Maintenance, replacement or repair of the emission control devices and systems may be performed by any ATV repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

Bef ore You Service Your Honda

The Importance of Maintenance ..........................................................

. 73

Maintenance Safety ..............................................................................

. 74

Important Safety Precautions ...........................................................

. 75

Maintenance Schedule .........................................................................

. 76

Maintenance Record .............................................................................

. 80

Service Preparations

Maintenance Component Locations .....................................................

. 81

Tool Kit ................................................................................................

. 84

Owner’s Manual Storage ......................................................................

. 85

Seat Removal .......................................................................................

. 86

(cont’d)


71

06/04/27 10:36:53 31HM3740_081


Service Procedures

Fluids & Filters

Fuel ......................................................................................................

. 87

Engine Oil & Filter ...............................................................................

. 92

Air Cleaner ...........................................................................................

. 99

Engine

Throttle ...............................................................................................

. 103

Clutch System ....................................................................................

. 105

Reverse Lock System .........................................................................

. 109

Engine Idle Speed ..............................................................................

. 110

Spark Plug ..........................................................................................

. 111

Valves .................................................................................................

. 114

Spark Arrester ....................................................................................

. 115

Chassis

Suspension .........................................................................................

. 116

Brakes .................................................................................................

. 119

Tires ...................................................................................................

. 128

Engine Guard & Skid Plates ...............................................................

. 135

Drive Chain ........................................................................................

. 136

Electrical

Battery ................................................................................................

. 143

Appearance Care ................................................................................

. 148

72


06/04/27 10:36:59 31HM3740_082

The Importance of Maintenance

A well-maintained ATV is essential for safe, economical, and troublefree riding. It will also help reduce air pollution. Careful pre-ride inspections and good maintenance are especially important because your

ATV is designed to be ridden over rough off-road terrain.

To help your properly care for your ATV, this section of the manual provides a Maintenance Schedule. The service intervals in this schedule are based on average riding conditions.

More frequent service is needed if you subject your ATV to severe use or ride in unusually wet or dusty areas.

Improperly maintaining this ATV or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed.

Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

Frequent servicing of the air cleaner is especially important to help you avoid a possible costly engine repair.

If your ATV overturns or is involved in a crash, be sure your Honda dealer inspects all major parts, even if you are able to make some repairs.


73

06/04/27 10:37:04 31HM3740_083

Maintenance Safety

This section includes instructions on how to perform some important maintenance tasks. If you have basic mechanical skills, you can perform many of these tasks with the tools provided with your ATV.

Other tasks that are more difficult and require special tools are best performed by professionals. Removing the wheels should normally be handled only by a Honda technician or other qualified mechanic.

Instructions are included in this manual only to assist in emergency service.

Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner’s manual.

74


06/04/27 10:37:10 31HM3740_084

Maintenance Safety

Important Safety Precautions

Make sure the engine is off before you begin any maintenance or repairs. This will help eliminate several potential hazards:

Carbon monoxide poisoning from engine exhaust.

Be sure there is adequate ventilation whenever you operate the engine.

Burns from hot ATV parts.

Let the engine and exhaust system cool before touching.

Injury from moving parts.

Do not run the engine unless instructed to do so.

Read the instructions before you begin, and make sure you have the tools and skills required.

To reduce the possibility of a fire or explosion, be careful when working around gasoline. Use only non-flammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts.

Remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new genuine Honda parts or other equivalents for repair and replacement. If you have the tools and skills required for additional maintenance jobs, you can purchase an official Honda

Service Manual (page 196 ).


75

06/04/27 10:37:15 31HM3740_085

Maintenance Schedule

The required Maintenance Schedule that follows specifies how often you should have your ATV serviced, and what things need attention. It is essential to have your ATV serviced as scheduled to maintain safe, dependable performance and proper emission control.

The service intervals in this Maintenance Schedule are based on average riding conditions. Some items will need more frequent service if you ride in unusually wet or dusty areas or at full throttle. Consult your

Honda dealer for recommendations applicable to your individual needs and use.

Some items in the Maintenance Schedule can be performed with basic mechanical skills and hand tools. Procedures for these items are provided in this manual. Other items involve more extensive procedures and may require special training, tools, and equipment. We recommend that you have your Honda dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment.

Procedures for such items in this schedule are provided in an official

Honda Service Manual available for purchase (page 196 ).

If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. If you decide to do your own maintenance, use only genuine Honda parts or their equivalents for repair or replacement to ensure the best quality and reliability.

76


06/04/27 10:37:23 31HM3740_086


Perform the pre-ride inspection (page 31 ) and owner maintenance on this section at each scheduled maintenance period.

Each item on the maintenance schedule requires some mechanical knowledge. Certain items (particularly those marked ＊ and ＊＊ ) may require more technical information and tools. Consult your Honda dealer.

＊

＊＊

Should be serviced by your Honda dealer, unless you have the proper tools and service data and are mechanically qualified. Refer to the official Honda Service Manual (page 196 ).

In the interest of safety, we recommend these items be serviced only by your Honda dealer.

Summary of Maintenance Schedule Notes & Procedures:

NOTES:

1.

2.

Service more frequently when riding in dusty areas, sand or snow.

Service more frequently after riding in very wet or muddy conditions.

3.

Replace every 2 years. Replacement requires mechanical skill. Refer to the official Honda service manual.


77

06/04/27 10:37:30 31HM3740_087


Maintenance Procedures:

I: inspect and clean, adjust, lubricate, or replace, if necessary

C: clean

A: adjust

L: lubricate

R: replace

FREQUENCY

ITEMS

FUEL LINE

FUEL STRAINER

SCREEN

THROTTLE OPERATION

AIR CLEANER

AIR CLEANER HOUSING

DRAIN TUBE

SPARK PLUG

VALVE CLEARANCE

ENGINE OIL

WHICHEVER

COMES

FIRST

NOTE

NOTE 1

NOTE 2 mi km

HOURS

INITIAL

MAINT.

100

150

20

REGULAR

MAINT. INTERVAL

600

1000

100

C

I

1200

2000

200

I

C

I

C

I

Refer to

99 page

103

−

90

−

−

104

101

102

ENGINE OIL FILTER

ENGINE IDLE SPEED

I I

I

I

I

INITIAL=100mi (150km),

20 operating hours or 1 month : R

REGULAR=Every 600mi (1000km),

100 operating hours or 12 months : R

R

I

R

I

R

I

111 − 113

114

92 − 98

96 − 98

110


78


06/04/27 10:37:38 31HM3740_088


ITEMS

DRIVE CHAIN

FREQUENCY

WHICHEVER

COMES

FIRST

NOTE

NOTE 1,2 mi km

HOURS

DRIVE CHAIN SLIDER

BRAKE FLUID

BRAKE PAD WEAR

BRAKELIGHT SWITCH

BRAKE SYSTEM

REVERSE LOCK

SYSTEM

SKID PLATES, ENGINE

GUARD

CLUTCH SYSTEM

SUSPENSION

SPARK ARRESTER

NUTS, BOLTS,

FASTENERS

WHEELS/TIRES

STEERING SHAFT

HOLDER BEARINGS

STEERING SYSTEM

NOTE 3

NOTE 1,2

INITIAL

MAINT.

100

150

20

I,L

I

I

I

REGULAR

MAINT. INTERVAL

600

1000

100

1200

2000

200

I,L EVERY 300mi (500km)

I

I

I or 50 operating hours

I

I

I

I

I

I

I

I

Refer to page

136 − 142

138

119 − 122

123

125

119 − 127

109

I

I

I

I

I

I

C

I

I

C

I

I

I

I

I

I

105

116

135

−

−

108

118

115

−

−

−

−


In the interest of safety, we recommend these items be serviced only by your Honda dealer.


79

06/04/27 10:37:44 31HM3740_089

Maintenance Record

Keeping an accurate maintenance record will help ensure that your ATV is properly maintained. Retain detailed receipts to verify the maintenance was performed. If the ATV is sold, these receipts should be transferred with the ATV to the new owner. Make sure whoever performs the maintenance completes this record. All scheduled maintenance, including the 100 mile (150 km) or 20 hours initial maintenance, is considered a normal owner operating cost and will be charged for by your dealer. Use the space under Notes to record anything you want to remind yourself about or mention to your dealer.

Date Performed By: Notes Miles (km) or hours

100 (150) or

20

600 (1,000) or

100

1,200 (2,000) or

200

1,800 (3,000) or

300

2,400 (4,000) or

400

3,000 (5,000) or

500

3,600 (6,000) or

600

4,200 (7,000) or

700

4,800 (8,000) or

800

80


06/04/27 10:37:48 31HM3740_090

Maintenance Component Locations clutch lever/parking brake lever front brake fluid reservoir front brake lever fuel fill cap throttle lever


81

06/04/27 10:37:53 31HM3740_091

Maintenance Component Locations spark arrester air cleaner engine oil filter front suspension spring pre-load adjuster rear brake fluid reservoir front brake caliper rear brakelight switch rear brake pedal engine oil filler cap/ dipstick engine oil drain bolt

82


06/04/27 10:37:58 31HM3740_092

Maintenance Component Locations choke lever engine idle speed main fuse spark plug air pressure gauge tool kit owner’s manual rear brake caliper rear suspension spring pre-load adjuster drive chain battery air cleaner housing drain tube


83

06/04/27 10:38:03 31HM3740_093

Tool Kit

1 86 ),

An optional, larger tool kit may be available. Check with your Honda dealer’s parts department.

(3)

(1) tool kit

(2) seat

(3) rubber band

(2)

(1)

84


06/04/27 10:38:09 31HM3740_094

Owner’s Manual Storage

Your ATV provides storage for the owner’s manual so you’ll have it

Be careful not to flood this area when washing your ATV or through water.

(2)

(3)

(1)

(4)

(1) owner’s manual

(2) plastic document bag

(3) seat

(4) rubber band


85

06/04/27 10:38:18 31HM3740_095

Seat Removal

Refer to Saf ety Precautions on page 75 .

The seat must be removed for air cleaner and fuse maintenance and access to the tool kit and owner’s manual.

(2) (5)

(3)

(1)

(3)

(4)

(1) seat lock lever

(2) seat

(3) front prongs

Removal

1.

2.

Installation

1.

2.

Press down on the seat until it locks.

(4) hooks

(5) studs

86


06/04/27 10:38:26 31HM3740_096

Fuel


Fuel Recommendation

type pump octane number unleaded

86 (or higher)

We recommend that you use unleaded fuel because it produces fewer engine deposits and extends the life of exhaust system components.

Your engine is designed to use any gasoline that has a pump octane number of 91 or higher. Gasoline pumps at service stations normally display the pump octane number. For information on the use of oxygenated fuels, see page 192 .

Use of lower octane gasoline can cause persistent ‘‘pinging’’ or ‘‘spark knock’’ (a loud rapping noise) which, if severe, can lead to engine damage. Light pinging experienced while operating under a heavy load, such as climbing a hill, is no cause for concern.

If pinging or spark knock occurs at a steady engine speed under normal load, change brands of gasoline. If pinging or spark knock persists, consult your Honda dealer.

Never use stale or contaminated gasoline or an oil/gasoline mixture.

Avoid getting dirt, dust, or water in the fuel tank.


87

06/04/27 10:38:35 31HM3740_097

Fuel

Fuel Capacity

Fuel tank capacity, including reserve:

2.25 US gal (8.5 )

Reserve capacity:

0.48 US gal (1.8 )

The tank should be refilled as soon as possible after switching to reserve, and the fuel valve should be returned to the ON position after refueling to avoid running out of fuel with no reserve.

Refueling Procedure


(2)

(3)

(4)

(6)

(5)

(1)

(1) fuel fill cap

(2) breather tube

(3) handlebar cover hole

88


(4) filler neck

(5) arrow

(6) reference mark

06/04/27 10:38:43 31HM3740_098

Fuel

1.

2.

3.

Avoid over filling the tank. There should be no fuel in the filler neck.

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when handling fuel.

Stop the engine and keep heat, sparks and flame away.

Handle fuel only outdoors.

Wipe up spills immediately.

4.

5.

6.

cover.

Insert the breather tube into the handlebar cover hole.

If the fuel valve was set to RES, turn the fuel valve ON.

If you replace the fuel fill cap, use only a genuine Honda replacement part.


89

06/04/27 10:38:50 31HM3740_099

Fuel

Fuel Strainer Screen


The fuel strainer is in the fuel valve. The strainer has a fine mesh screen which accumulates in the screen must be removed periodically, or the fuel flow will eventually be restricted.

1.

Turn the fuel valve OFF.

2.

3.

4.

Wash the screen in non-flammable (high flash point) solvent such as kerosene − not gasoline.

90


06/04/27 10:38:55 31HM3740_100

Fuel

5.

6.

Reassemble by reversing the disassembly sequence.

Check to be sure the O-ring is in place.

7.

Turn the fuel valve ON, and check for leaks. Correct if necessary.

LEFT SIDE

(3)

(1) fuel strainer cap

(2) O-ring

(3) strainer screen

(2)

(1)


91

06/04/27 10:38:59 31HM3740_101

Engine Oil & Filter

Engine oil quality is a major factor that affects both the performance and the service life of the engine.

Using the proper oil (page 93 ) and filter, and regularly checking, adding, and changing oil will help extend your engine’s life. Even the best oil wears out. Changing oil helps get rid of dirt and deposits in the engine. Operating the engine with old or dirty oil can damage your engine. Running the engine with insufficient oil can cause serious damage to the engine and transmission.

Change the engine oil as specified in the maintenance schedule on page

76 . When running in very dusty conditions, oil changes should be performed more frequently than specified in the maintenance schedule.

92


06/04/27 10:39:09 31HM3740_102


Oil Recommendation

API classification viscosity (weight)

JASO T 903 standard suggested oil ＊

SG or higher except oils labeled as energy conserving on the circular API service label

SAE 10W-30

MA

Pro Honda GN4 4-stroke oil (USA &

Canada), or Honda 4-stroke oil (Canada only), or an equivalent motorcycle oil.

＊

Suggested oils are equal in performance to SJ oils that are not labeled as energy conserving on the circular API service label.

Your ATV does not need oil additives. Use the recommended oil.

Do not use oils with graphite or molybdenum additives. They may adversely affect clutch operation.

Do not use API SH or higher oils displaying a circular API ‘‘energy conserving’’ service label on the container. They may affect lubrication and clutch performance.

NOT RECOMMENDED OK

Do not use non-detergent, vegetable, or castor based racing oils.


93

06/04/27 10:39:16 31HM3740_103


Other viscosities shown in the following chart may be used when the average temperature in your riding area is within the indicated range.

JASO T 903 standard

The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines.

There are two classes: MA and MB.

Oil conforming to the standard is labeled on the oil container. For example, the following label shows the MA classification.

(1)

(2)

(1) code number of the sales company of the oil

(2) oil classification

94


06/04/27 10:39:25 31HM3740_104


Checking & Adding Oil


Check the engine oil level each day before operating your ATV and add if needed.

1.

Park your ATV on a firm, level surface.

2.

Start the engine in a well-ventilated area and let it idle for 3 − 5 minutes. Stop the engine and wait 2 − 3 minutes.

3.

4.

and wipe it clean.

Insert the oil filler cap/dipstick without screwing it in, then remove the oil filler cap/dipstick and check the oil level. The oil level should

5.

the oil filler cap/dipstick.

If required, add the specified oil into the filler cap hole, up to the

6.

upper level mark on the oil filler cap/dipstick. Do not overfill.

Reinstall the oil filler cap/dipstick.

Running the engine with an improper oil level can cause serious engine damage.

RIGHT SIDE

(2)

(3)

(1) oil filler cap/dipstick

(1)

(2) upper level mark

(3) lower level mark


95

06/04/27 10:39:33 31HM3740_105


Changing Engine Oil & Filter


Your ATV’s oil filter has very specific performance requirements. Use a new genuine Honda oil filter specified for your model or a filter of equal quality.

Using the wrong oil f ilter may result in leaks or premature engine damage.

This procedure requires mechanical skill and professional tools such as a torque wrench as well as a means for disposing of the drained fluid

(page 162 ). If you do not have the skills or the tools, see your Honda dealer.

Drain the Engine Oil:

1.

With the ATV on the level ground, remove the oil filler cap/dipstick from the right crankcase cover.

2.

Place an oil drain pan under the crankcase and remove the oil drain

UNDER ENGINE

(1) oil drain plug

96


(1)

06/04/27 10:39:41 31HM3740_106


Install a New Engine Oil Filter:

1.

2.

3.

then install a new oil filter. Use only the Honda genuine oil filter or a filter of equivalent quality specified for your model. Using the wrong

Honda filter or a non-Honda filter which is not of equivalent quality may cause engine damage.

on the filter body, near the seal.

Improper installation of the oil f ilter can cause serious engine damage.

RIGHT SIDE

(5)

(7)

(3)

(4)

(1)

(1) oil filter cover

(2) bolts

(3) oil filter

(4) O-rings

(6)

(2)

(5) spring

(6) rubber seal

(7) OUTSIDE mark

(cont’d)


97

06/04/27 10:39:53 31HM3740_107


4.

Reinstall the oil filter cover, making sure the bolts are tightened to the specified torque:

7 lbf·ft (10 N·m , 1.0 kgf·m)

5.

Pour the drained oil into a suitable container and dispose of it in an approved manner (page 162 ).

Improper disposal of drained f luids is harmf ul to the environment.

Add Engine Oil:

1.

Check that the drain plug sealing washer is in good condition. If

2.

necessary, replace the sealing washer.

Reinstall the oil drain plug and tighten it to the specified torque:

18 lbf·ft (24 N·m , 2.4 kgf·m)

3.

Fill the crankcase with the recommended grade oil approximately:

1.69 US qt (1.60 )

4.

5.

6.

Reinstall the oil filler cap/dipstick.

Start the engine and let it idle for 3 − 5 minutes.

Stop the engine, wait 2 − 3 minutes and check the oil level. Make sure the oil is between the upper and lower level marks on the oil filler

7.

cap/dipstick. If necessary, add more oil but do not overfill.

Check that there are no oil leaks.

If a torque wrench is not used for installation, see your Honda dealer as soon as possible to verify proper assembly.

98


06/04/27 10:40:00 31HM3740_108

Air Cleaner


Proper air cleaner maintenance is very important for off-road vehicles.

A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt, dust, mud, and other impurities to pass into the engine.

Service the air cleaner more frequently if you ride in unusually wet or dusty areas. Your Honda dealer can help you determine the correct service interval for your riding conditions.

Your ATV’s air cleaner has very specific performance requirements.

Use a new genuine Honda air cleaner specified for your model or an air cleaner of equal quality.

Using the wrong air cleaner may result in premature engine damage.

Proper air cleaner maintenance can prevent premature engine wear or damage, expensive repairs, low engine power, poor gas mileage, and spark plug fouling.

Improper or lack of proper air cleaner maintenance can cause poor perf ormance and premature engine wear.


99

06/04/27 10:40:09 31HM3740_109

Air Cleaner

Cleaning

1.

Remove the seat (page 86 ).

UNDER SEAT

(1)

(2)

(1)

(1) retainer clips (2) air cleaner housing cover

2.

3.

4.

the air cleaner housing.

5.

6.

7.

Remove the air cleaner ( ) from the air cleaner body ( 7 ).

Gently wash the air cleaner in clean, non-flammable (high flash point) solvent such as kerosene − not gasoline. After cleaning, gently

8.

squeeze out the remaining solvent. Avoid twisting or wringing the air cleaner. This can tear the foam.

Inspect for tears or cracks in the foam or seams of the air cleaner.

Replace the air cleaner if it is damaged.

100


06/04/27 10:40:19 31HM3740_110

Air Cleaner

9.

10.

Allow the air cleaner to dry thoroughly before applying oil. A wet air cleaner will not fully absorb the oil.

Pour clean Pro Honda Foam Filter Oil or an equivalent (Canada:

Honda Foam Filter Oil or an equivalent) over the entire surface of the air cleaner. Use both hands to evenly spread the oil into the air cleaner.

Gently squeeze out any excess oil. (To keep your hands dry, place the air cleaner in a clean plastic bag before spreading the oil into the air cleaner.)

UNDER SEAT

(8)

(5)

(6)

(4)

(3)

(7)

(3) screw

(4) air cleaner assembly

(5) clamp

(6) air cleaner

(7) air cleaner body

(8) FRONT mark

11.

12.

Install the air cleaner on the air cleaner body.

Apply a thin coat of grease to the sealing surface of the air cleaner assembly.

Install the clamp.

13.

14.

15.

16.

Insert the air cleaner assembly into the air cleaner housing.

Fasten the screw.

Install the remaining parts in the reverse order of removal.

Install the air cleaner housing cover with the FRONT mark ( 8 ) facing forward.


101

06/04/27 10:40:25 31HM3740_111

Air Cleaner

Air Cleaner Housing Drain Tube

The air cleaner housing drain tube should be serviced in accordance with the Maintenance Schedule. (Riding through water may require more frequent inspection.) If deposits can be seen in the drain tube, the tube must be cleaned before starting the vehicle.

LEFT SIDE

(3)

(1) drain tube

(2) clip

(3) air cleaner housing

1.

2.

3.

Drain the deposits.

Reinstall the drain tube, securing it with the clip.

(2)

(1)

102


06/04/27 10:40:36 31HM3740_112

Throttle

Throttle Freeplay


RIGHT HANDLEBAR

( ( ) )

( ( ) )

1/8 − 5/16 in

(3 − 8 mm)

(2)

(3) (4) (1)

(1) throttle lever

(2) rubber sleeve

(3) throttle cable adjuster

(4) lock nut

Inspection

Freeplay:

1/8 − 5/16 in (3 − 8 mm)

Adjustment

1.

( ＋ ) increase freeplay

( − ) decrease freeplay

2.

3.

4.

5.

Turn the adjuster to obtain the correct freeplay.

Tighten the lock nut and reinstall the sleeve.

After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions.


103

06/04/27 10:40:43 31HM3740_113

Throttle

Throttle Inspection


1.

Check that the throttle assembly is positioned properly and the securing bolts are tight.

2.

Check for smooth operation of the throttle lever from fully open to fully closed in all steering positions. If there is a problem, see your

3.

Honda dealer.

Inspect the condition of the throttle cables from the throttle lever

4.

5.

down to the carburetor. If the cable is kinked or chafed, have it replaced.

Check the cables for tension or stress in all steering positions.

Lubricate the cables with a commercially-available cable lubricant to prevent premature wear and corrosion.

104


06/04/27 10:40:50 31HM3740_114

Clutch Adjustment


LEFT HANDLEBAR

(1)

3/8 − 3/4 in

(10 − 20 mm)

Clutch System


Clutch adjustment may be required if the ATV tends to creep or if the clutch slips when shifting into gear, causing acceleration to lag behind engine speed.

Inspection

Check freeplay.

Freeplay:

3/8 − 3/4 in (10 − 20 mm)

If necessary, adjust to the specified range.

Improper freeplay adjustment can cause premature clutch wear.


105

06/04/27 10:40:59 31HM3740_115

Clutch System

Upper Adjustment

Minor adjustments are generally made with the upper clutch cable adjuster.

LEFT HANDLEBAR

(3)

(2)

( ( ) )

( ( ) )

(4)

(2) dust cover

(3) upper lock nut

(4) upper clutch cable adjuster

(

( ＋

−

) increase freeplay

) decrease freeplay

1.

2.

3.

freeplay.

4.

5.

Tighten the lock nut and check the freeplay again.

Pull on the dust cover.

If proper adjustment cannot be obtained or the clutch does not work correctly, the cable or clutch friction discs may be worn. See your

Honda dealer.

106


06/04/27 10:41:08 31HM3740_116

Clutch System

Lower Adjustment

The lower clutch cable adjuster is used if the upper clutch cable adjuster is threaded out near its limit − or the correct freeplay cannot be obtained.

LEFT SIDE

(6)

( ( ) )

( ( ) )

(5)

(5) lower adjusting nut

(6) lower lock nut



1.

2.

normal position.

3.

4.

5.

the lower end of the cable.

Turn the lower adjusting nut to obtain the specified freeplay.

Hold the lower adjusting nut and tighten the lower lock nut. Check the adjustment.

(cont’d)


107

06/04/27 10:41:14 31HM3740_117

Clutch System

6.

Start the engine, pull the clutch lever/parking brake lever in, and shift into gear. Make sure the engine does not stall and the ATV does not creep. Gradually release the clutch lever/parking brake lever and open the throttle. Your ATV should move smoothly and accelerate gradually.

Check the clutch lever/parking brake lever and clutch cable for loose connections or other damage. If the clutch cable is worn or kinked, have it replaced by your Honda dealer.

Other Inspections & Lubrication

Check that the clutch lever/parking brake lever assembly is positioned properly and the securing bolts are tight.

Check the clutch cable for kinks or signs of wear. If necessary, have it replaced.

Lubricate the clutch cable with a commercially-available cable lubricant to prevent premature wear and corrosion.

108


06/04/27 10:41:23 31HM3740_118

Reverse Lock System

Reverse Lock System Adjustment


RIGHT SIDE RIGHT CRANKCASE

(1)

(2)

( ( ) )

( ( ) )

3/8 − 3/4in

(10 − 20mm)

(1) reverse assist lever

(2) lock nut

(3) adjusting nut

1.

3/8 − 3/4 in (10 − 20 mm)

2.

After adjustment, tighten the lock nut securely.

(3)



Other Inspection

Check the reverse assist lever and cable for loose connections or other damage. If the cable is worn or kinked, have it replaced by your Honda dealer.


109

06/04/27 10:41:33 31HM3740_119

Engine Idle Speed

The best way to assure proper carburetion is to see your Honda dealer for regularly scheduled servicing, including carburetor adjustment.

Remember, idle speed adjustment is not a ‘‘cure-all’’ for other problems in your engine’s fuel-delivery system. Adjusting the idle will not compensate for a fault elsewhere.

The engine must be at normal operating temperature for accurate idle speed adjustment.

For information about high altitude carburetor adjustment, see page 187 .

Idle Speed Adjustment


LEFT SIDE

( ( ) )

(1)

( ( ) )

(1) throttle stop screw ( ＋ ) increase

( − ) decrease

1.

2.

3.

If the engine is cold, start it and warm it up with ten minutes of stopand-go riding. Stop the engine.


Connect a tachometer to the engine.

4.

Shift into neutral. Start the engine.

5.

Idle speed (in neutral):

1,400 ± 100 rpm

110


06/04/27 10:41:44 31HM3740_120

Spark Plug

Spark Plug Recommendation

standard spark plug for cold climate

(below 5°C, 41°F) for extended high speed riding

DR8ES-L (NGK)

X24ESR-U (DENSO)

DR7ES (NGK)

X22ESR-U (DENSO)

DR8ES (NGK)

X27ESR-U (DENSO) or or or

Use only the recommended type of spark plug in the recommended heat range.

Using spark plugs with an improper heat range can cause engine damage.

Spark Plug Replacement & Inspection


1.

2.

Clean any dirt from around the spark plug base.

Disconnect the spark plug cap. Take care to avoid damaging the spark plug wire when disconnecting the cap.

3.

Using a spark plug wrench provided in the tool kit, remove the spark plug.

(1)

(1) spark plug cap (cont’d)


111

06/04/27 10:41:51 31HM3740_121

Spark Plug

4.

Inspect the electrode and center porcelain for deposits, corrosion, or carbon fouling. If the corrosion or deposits are heavy, replace the plug. Clean a carbon or wet-fouled plug with a plug cleaner, if available, or a wire brush. Inspect the spark plug electrodes for wear.

5.

Discard the spark plug if there is apparent wear or if the insulator is cracked or chipped.

6.

insulator tip appear unusually fouled or burned, we suggest that you contact your Honda dealer.

adjustment is necessary, bend the side electrode carefully.

The gap should be:

0.024

− 0.028 in (0.60

− 0.70 mm)

(3)

(4)

(2)

0.024

− 0.028 in

(0.60

− 0.70 mm)

(2) center electrode

(3) side electrode

112


(4) spark plug gap

06/04/27 10:41:57 31HM3740_122

Spark Plug

7.

With the plug washer attached, thread the spark plug in by hand to prevent cross-threading.

8.

Tighten the spark plug:

If the old plug is good:

1/8 turn after it seats.

If installing a new plug, tighten it twice to prevent loosening: a) First, tighten the plug:

NGK: 3/4 turn after it seats.

DENSO: 1/2 turn after it seats.

b) Then loosen the plug.

c) Next, tighten the plug again:

1/8 turn after it seats.

An improperly tightened spark plug can damage the engine. If a plug is too loose, a piston may be damaged. If a plug is too tight, the threads may be damaged.

9.

Reinstall the spark plug cap. Take care to avoid pinching any cables or wires.


113

06/04/27 10:42:03 31HM3740_123

Valves

Valve Inspection


Valve clearance should be:

0.004 in (0.10 mm)

Excessive clearance will cause noise. Insufficient clearance will cause loss of power and possibly damage the valves.

For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official

Honda Service Manual. All others should have valves adjusted by your

Honda dealer.

114


06/04/27 10:42:13 31HM3740_124

Spark Arrester


The exhaust system must be periodically purged of accumulated carbon.

Regular servicing prevents carbon build up (which can diminish engine performance) and also complies with USDA regulations for regular maintenance to assure proper function. The spark arrester prevents random sparks from the combustion process in your engine from reaching the environment.

The use of safety glasses is recommended for this procedure.

Because of the possible fire hazard, check that there are no combustible materials in the area before purging the spark arrester.

REAR (2)

(3)

(4)

(1)

(1) bolts

(2) gasket

(3) spark arrester lid

(4) spark arrester screws

1.

Select a well-ventilated area free of combustible materials and make sure the exhaust pipe is cool.

2.

3.

Start the engine and rev it up approximately twenty times while momentarily creating exhaust system back pressure by blocking the

4.

5.

end of the muffler with a shop towel.

Stop the engine and allow the exhaust pipe to cool.

Reinstall the removed parts and tighten the bolts securely.

arrester body at all times for the spark arrester to be effective.


115

06/04/27 10:42:20 31HM3740_125

Suspension

Your front and rear suspension systems use springs and hydraulic damping devices that suspend your weight and most of the weight of your ATV.

The spring pre-loads for your front and rear suspension systems adjust the amount of force required to begin compression of the spring.

The oil damper systems hydraulically control the natural compression and rebound of the suspension springs so that traction and comfort are maintained as the wheels ride over road surfaces.

Consider adjusting your suspensions pre-load whenever you change your normal load, by adding or subtracting accessories, or when the road or riding conditions change.

The way you ride your ATV and the type of ride you want to experience can also influence your suspension needs.

Lower spring pre-load provides a softer ride and is usually preferred for light loads and smooth roads. Higher spring pre-load provides a firmer ride and is recommended for heavy loads, rough road conditions, and faster, more challenging riding.

Suspension Adjustment

The suspensions can be adjusted for rider weight and riding conditions by changing the spring pre-load.

Do not attempt to disassemble, service, or dispose of the damper; see your Honda dealer. The instructions found in this owner’s manual are limited to adjustments of the shock assembly only.

116


06/04/27 10:42:28 31HM3740_126

Suspension

Suspension Spring Pre-Load


FRONT REAR

5

4 3

2

1

(2)

(1)

1 2 3 4 5

(1) spring pre-load adjuster

(2) pin spanner riding conditions.

(1)

(cont’d)


117

06/04/27 10:42:33 31HM3740_127

Suspension

Front

Position 1: standard position.

Positions 2 to 5: for when the ATV is more heavily loaded. (Also increase spring pre-load for stiffer suspension.)

Rear

Position 1: for a light load and smooth road conditions.

Position 2: standard position.

Positions 3 to 5: for when the ATV is more heavily loaded. (Also increase spring pre-load for stiffer suspension.)

Make sure that both shock absorbers are adjusted to the same position.

Always adjust the shock absorber position in sequence (1-2-3-4-5 or 5-

4-3-2-1). Attempting to adjust directly from 1 to 5 or 5 to 1 may damage the shock absorber.

118


06/04/27 10:42:41 31HM3740_128

Brakes

The hydraulic braking systems on your ATV dissipate the heat generated by the friction of the brake pads on the brake discs as the wheels are slowed.

As the brake pads wear, the brake fluid level will drop. A leak in the system will also cause the level to drop.

There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks.

If the brake lever or brake pedal freeplay does not feel within the normal range while riding, check the brake pads for wear (page 123 ).

Worn pads should be replaced. If the pads are not worn beyond the recommended limit, there is probably air in the brake system. See your

Honda dealer to have the air bled from the system.

Brake Fluid Recommendation

brake fluid Honda DOT 4 Brake Fluid

The recommended brake fluid is Honda DOT 4 Brake Fluid, or any brake fluid of equal quality and performance. Use fresh brake fluid from a sealed container. Be sure to read the label before opening the sealed container. An opened container may be contaminated or may have absorbed moisture from the air.


119

06/04/27 10:42:48 31HM3740_129

Brakes

Fluid Level Inspection


If your inspection indicates a low fluid level, have your Honda dealer add the recommended fluid.

Do not add or replace brake fluid, except in an emergency. If you do add fluid, have your Honda dealer check the system as soon as possible.

Brake f luid can damage plastic and painted surf aces. Handle with care.

Wipe up spills immediately. Avoid contact with skin or eyes. In case of contact, wash thoroughly and call a doctor immediately if it contacts your eyes.

Front Brake Fluid Level

RIGHT HANDLEBAR

(1) LOWER level mark

120


(1)

06/04/27 10:42:55 31HM3740_130

Brakes

With the ATV in an upright position, check the fluid level.

below the LOWER level mark, check the brake pads for wear

(page 123 ).

Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.

Rear Brake Fluid Level

RIGHT SIDE

(2)

(3)

(2) UPPER level mark

(3) LOWER level mark

With the ATV in an upright position, check the fluid level.

level is at or below the LOWER level mark, check the brake pads for wear (page 123 ).

Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks.


121

06/04/27 10:42:59 31HM3740_131

Brakes

Other Inspections

Make sure there are no fluid leaks.

Check for deterioration or cracks in the hoses and fittings. If the hoses are worn or cracked, have them replaced by your Honda dealer.

122


06/04/27 10:43:06 31HM3740_132

Brakes

Brake Pad Wear


Brake pad wear will depend upon the severity of usage and riding conditions. The pads will wear faster in wet or muddy conditions.

Inspect the pads visually during all regular service intervals to determine the pad wear.

RIGHT FRONT (Left side similar) REAR

(2) (1)

(2)

(1)

(1) wear indicator (2) edge of reference mark

Front brake pads/Rear brake pads − 1 your Honda dealer for this replacement.

Always inspect both pads in both the right and left front brake calipers.


123

06/04/27 10:43:11 31HM3740_133

Brakes

Other Inspections

Make sure there are no fluid leaks.

Check for deterioration or cracks in the hoses and fittings.

The rear brake pedal pivot must be inspected according to the

Maintenance Schedule.

See your Honda dealer for this service.

124


06/04/27 10:43:18 31HM3740_134

Brakes

Brakelight Switch Adjustment


Rear Brake Only: near the crankcase from time to time. The brakelight should turn on at

0.6 in (15 mm) of pedal stroke. Adjustment is done by turning the

RIGHT SIDE

(2)

( B )

( A )

(1) brakelight switch

(2) adjusting nut

(1)


125

06/04/27 10:43:26 31HM3740_135

Brakes

Parking Brake Adjustment


Parking brake adjustment may be required if the parking brake does not hold properly.

LEFT HANDLEBAR REAR

(2)

(1)

(5)

(1) dust cover

(2) lock nut

(3) adjuster

(3)

(6)

(4)

(4) lock nut

(5) parking brake arm

(6) adjusting bolt

1.

Temporarily adjust the clutch lever/parking brake lever freeplay to more than 1 3/16 in (30 mm) (page 105 ).

2.

3.

4.

5.

Then turn the adjusting bolt 1/8 counterclockwise, and tighten the lock nut.

126


06/04/27 10:43:33 31HM3740_136

Brakes

6.

Measure the distance the clutch lever/parking brake lever has moved; the distance should be:

1 − 1 3/16 in (25 − 30 mm)

LEFT HANDLEBAR

(8) (7)

1 −

(25

1 3/16 in

− 30 mm)

(7) parking brake pin


Check the clutch lever/parking brake lever and parking brake cable for loose connections or other damages. If the parking brake cable is worn or kinked, have it replaced by your Honda dealer.

Other Inspections & Lubrication

Check that the clutch lever/parking brake lever assembly is positioned properly and the securing bolts are tight.

Check the parking brake cable for kinks or signs of wear. If necessary, have it replaced.

Lubricate the parking brake cable with a commercially-available cable lubricant to prevent premature wear and corrosion.


127

06/04/27 10:43:38 31HM3740_137

Tires

To safely operate your ATV, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

This ATV is equipped with low pressure tubeless tires. Although the tires are designed specifically for off-road use, they are not immune to punctures. Always select your riding area with care.

The following pages give detailed information on how and when to check your air pressure, how to inspect your tires for wear and damage, and our recommendations for tire repair and replacement.

128


06/04/27 10:43:43 31HM3740_138

Tires

Air Pressure


Properly inflated tires provide the best combination of handling, tread life, and riding comfort. Generally, underinflated tires wear unevenly, adversely affect handling, and are more likely to fail from being overheated. Overinflated tires make your ATV ride harshly, are more prone to damage from surface hazards, and wear unevenly.

Make sure the valve stem caps are secure. If necessary, install a new cap.


129

06/04/27 10:43:52 31HM3740_139

Tires

Always check air pressure when your tires are ‘‘cold.’’ If you check air pressure when your tires are ‘‘warm’’ − even if your ATV has only been ridden for a few miles − the readings will be higher. If you let air out of warm tires to match the recommended cold tire pressures, the tires will be underinflated. Be sure to check tire pressure at the riding site, since changes in altitude can affect air pressure.

The recommended ‘‘cold’’ tire pressures are:

RECOMMENDED

PRESSURE

MAXIMUM

PRESSURE

MINIMUM

PRESSURE

FRONT

4.4 psi (30 kPa ,

0.30 kgf/cm )

4.8 psi (33 kPa ,

0.33 kgf/cm )

4.0 psi (27 kPa ,

0.27 kgf/cm )

REAR

2.9 psi (20 kPa ,

0.20 kgf/cm )

3.3 psi (23 kPa ,

0.23 kgf/cm )

2.5 psi (17 kPa ,

0.17 kgf/cm )

130


06/04/27 10:43:59 31HM3740_140

Tires

A manually operated tire pump should be used rather than the high pressure system found in service stations. This will minimize the possibility of tire damage from overinflation. If you use a high pressure system at a service station, add air in small amounts and check the pressure increase frequently to prevent possible tire damage from overinflation.

Operating this ATV with improper tires, or with uneven tire pressure may cause loss of control, and you could be seriously injured or killed.

Always use the size and type tires specified in this owner’s manual for this vehicle.

Always maintain proper tire pressure as described in this owner’s manual.

Inspection


Whenever you check the tire pressures, you should also look for:

Bumps or bulges in the side of the tire or the tread. Replace any tire that has a bump or bulge.

Cuts, slits, or cracks in the tires. Replace the tire if you can see fabric or cord.

Nails or other foreign objects embedded in the side of the tire or tread.

Excessive tread wear.


131

06/04/27 10:44:08 31HM3740_141

Tires

Also, if you hit a pothole or other hard object while riding, stop as soon as you safely can and carefully inspect the tires for damage.

Tread Wear

Front

Rear

(1)

3/16 in

(4 mm)

(2)

NEW

Replace

(3)

(1) groove depth

(2) wear indicator

(3) wear indicator location mark

For best performance, you should replace a tire before the tread depth at the center reaches the following limits: front rear

3/16 in (4 mm)

3/16 in (4 mm)

132


06/04/27 10:44:15 31HM3740_142

Tires

Tire Repair


A tire that is repaired, either temporarily or permanently, will have lower speed and performance limits than a new or undamaged tire.

A temporary repair can sometimes be made in an emergency situation.

However, since a temporary repair may not hold, you must ride very slowly and have the tire replaced or permanently repaired as soon as possible. (For more information on temporary repairs, see

Flat Tire, page 169 .)

If You Have a

A permanent repair, such as an internal plug patch, can be made if a tire has only a small puncture in the tread area. However you may not be able to safely carry as much weight. If you choose to have a tire repaired, be sure the repair work is performed by a professional.

If you have a tire professionally repaired at a non-Honda facility, we recommend that you have the work checked by your Honda dealer.


133

06/04/27 10:44:26 31HM3740_143

Tires

Tire Replacement


The tires that came on your ATV were designed to match the performance capabilities of your ATV and provide the best combination of handling, braking, and comfort.

It is best to replace all four tires, however if that is not possible, you must replace the tires in pairs (front or rear) with tires of the same size and type as the originals. Never replace just one tire.

Installing improper tires on your ATV can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

The recommended tires for your ATV are: front rear

AT 22 × 7-10

AT 22 × 10-9

★★

★

OHTSU P/V 102

OHTSU P/V 702

When you replace a tire, remember:

Have the tire replaced by your Honda dealer if possible.

If you have a tire professionally replaced at a non-Honda facility, we recommended that you have the work checked by your Honda dealer.

134


06/04/27 10:44:32 31HM3740_144

Engine Guard & Skid Plates


(1)

(1) engine guard

(2)

(2) skid plates and the rear brake. Check the guard and plates for cracks, damage or looseness at intervals shown in the Maintenance Schedule.

Have the engine guard and skid plates replaced if they are cracked or damaged. If the guard and plate bolts are loose, tighten them securely.


135

06/04/27 10:44:40 31HM3740_145

Drive Chain

An endless (riveted master link) chain connects the countershaft and rear wheel sprockets. The O-ring chain uses rubber rings between the side plates of the pin and roller links to seal in the manufacturer-installed lubricating grease and keep out moisture and dirt.

The service life of the chain depends on proper lubrication and adjustment. Poor maintenance can cause premature wear or damage to the drive chain or sprockets.

The drive chain should be checked, adjusted, and lubricated as part of the pre-ride inspection (page 31 ).

Under severe usage, or when the ATV is ridden in unusually dusty or muddy areas, more frequent maintenance will be necessary.

Before servicing your drive chain, turn the engine OFF and check that your transmission is in neutral.

It is not necessary to remove or replace the drive chain to perform the recommended service in the Maintenance Schedule.

Inspection


1.

Chain slack should be checked by measuring the amount of chain slack midway between the sprockets. The amount of slack should be:

1 3/8 − 1 3/4 in (35 − 45 mm)

136


06/04/27 10:44:48 31HM3740_146

Drive Chain

LEFT SIDE

1 3/8 − 1 3/4 in

(35 − 45 mm)

(1)

(1) drive chain

2.

Check drive chain slack at several points along the chain. The slack should remain constant. If it isn’t, some links may be kinked and binding. Lubricating the chain will often eliminate binding and kinking.

Excessive chain slack may allow the drive chain to damage the engine cases.

3.

Inspect the drive chain for: damaged rollers loose pins dry or rusted links kinked or binding links excessive wear damaged or missing O-rings

Replace the drive chain (page 142 ) if it has damaged rollers, loose pins, or kinks that cannot be freed. Lubricate the drive chain (page 141 ) if it appears dry or shows signs of rust. Lubricate any kinked or binding links and work them free. Adjust chain slack if needed.

(cont’d)


137

06/04/27 10:44:55 31HM3740_147

Drive Chain

4.

When the depth of the grooves in the slider reaches 0.08

in ( 2.0

mm), the grooves to less than 0.08

in ( 2.0

mm).

Replace the slider when the depth of the grooves reaches the limit.

Service limit:

0.24 in (6.0 mm)

LEFT SIDE

(2) (3)

(2) drive chain slider (3) center ridges

5.

With the upper or lower section of drive chain tight between the sprockets measure the distance between a span of 21 pins from pin center to pin center. If the distance exceeds the service limit, the chain is worn out and should be replaced.

Service limit:

12.56 in (319.1 mm)

Measure a span of 21 pins

138


06/04/27 10:45:01 31HM3740_148

Drive Chain

6.

RIGHT SIDE

(4)

(4) chain roller

7.

Inspect the front and rear sprocket teeth for excessive wear or damage.

If necessary, have your Honda dealer replace a worn sprocket.

Damaged Sprocket

Teeth

REPLACE

Worn Sprocket

Teeth

REPLACE

Normal Sprocket Teeth

GOOD

Use of a new chain with worn sprockets will cause rapid chain wear.


139

06/04/27 10:45:09 31HM3740_149

Drive Chain

Adjustment


1.

2.

3.

Retighten the rear axle holder fixing bolts.

Rear axle holder fixing bolts torque:

16 lbf·ft (22 N·m , 2.2 kgf·m)

If a torque wrench is not used for installation, see your Honda dealer as soon as possible to verify proper assembly.

REAR

(3)

( B )

(1)

( A )

(1) Allen wrench

(2) fixing bolts

140


(2)

(3) adjuster

06/04/27 10:45:15 31HM3740_150

Lubrication


Drive Chain

Lubricate every 30 days of riding or sooner if chain appears dry.

Lubricate only with SAE 80 or 90 gear oil. Commercial chain lubricants may contain solvents which could damage the rubber O-rings.


141

06/04/27 10:45:22 31HM3740_151

Drive Chain

Removal, Cleaning & Replacement


Your ATV has an endless (riveted master link) type chain. It should only be removed or replaced by your Honda dealer.

The O-rings can be damaged by steam cleaning, high pressure washers, and certain solvents.

1.

Clean the side surfaces of the chain with a dry cloth. Use a high flashpoint solvent such as kerosene − not gasoline.

2.

Do not brush the rubber O-rings.

Brushing will damage them. Use of a solvent may also damage the

O-rings.

Inspect the drive chain for possible wear or damage.

Replace the drive chain if it has damaged rollers, loose fitting links, damaged O-rings, or otherwise appears unserviceable.

Replacement Chain:

DID520V or RK520 MOZ9

142


06/04/27 10:45:29 31HM3740_152

Battery

Your ATV has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water as you would with a conventional-type battery.

Your battery is a maintenance-f ree type and can be permanently damaged if the cap strip is removed.

Electrical accessories use current from the battery –– even when the ignition is OFF. Limited operation also allows the battery to discharge.

If you have electrical accessories on your ATV –– or do not ride frequently, we recommend that you charge the battery frequently (see

Battery Charging, page 147 ).

If you do not expect to ride your ATV for at least two weeks, we recommend you remove the battery –– or at least disconnect the battery cables (negative cable first).

If you plan to store your ATV, see Battery Storage, page 144 .

If your battery seems weak and/or is leaking electrolyte (causing slow starting or other electrical problems), see your Honda dealer.

WARNING: Battery posts, terminals and related accessories contain lead and lead compounds.

Wash your hands after handling.


143

06/04/27 10:45:36 31HM3740_153

Battery

Battery Storage


If you plan to store your ATV, we recommend you remove the battery and store it where it can be charged at least every 30 days to maintain its service life.

If you do not remove the battery, we recommend disconnecting the battery cables (negative cable first).

You will get the best storage results from removing the battery and slow

(trickle) charging it every 30 days (see Battery Charging, page 147 ).

Before you remove the battery, be sure to read all the information that follows, as well as the information on the battery label.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

144


06/04/27 10:45:46 31HM3740_154

Battery

The battery is located in a compartment under the left side rear fender.

LEFT SIDE

(3)

(1) (2)

(5)

(4)

(1) battery holder

(2) mount bolt

(3) negative ( − ) terminal lead

(4) battery

(5) positive ( ＋ ) terminal lead

Removal

1.

Make sure the ignition switch is OFF ( ).

2.

3.

4.

Remove the seat (page 86 ).

2

Disconnect the negative ( − 3 4 first, then disconnect the positive ( ＋ 5

5.

Remove the battery.

(cont’d)


145

06/04/27 10:45:53 31HM3740_155

Battery

6.

Charge the battery (see following section), unless you have been riding regularly.

7.

Store your battery in an easy-to-reach location off the floor, in an area protected from freezing temperature and direct sunlight.

8.

Clean the battery box after removing the battery for storage. Dry the battery box and, if paint is missing, re-paint the area.

9.

Slow charge the battery (see following section) once every 30 days.

Installation

1.

Reinstall in the reverse order of removal.

Be sure to connect the positive ( ＋ ) terminal first, then the negative

( − ) terminal.

2.

Check all bolts and other fasteners are secure.

146


06/04/27 10:45:59 31HM3740_156

Battery Charging


(1)

Battery

(1) ‘‘trickle’’ charger

Be sure to read the information that came with your battery charger and follow the instructions on the battery. Improper charging may damage the battery.

units can be left connected for long periods without risking damage to the battery. However, do not intentionally leave the charger connected longer than the time period recommended in the charger’s instructions.

Avoid using an automotive-type battery charger. An automotive charger can overheat an ATV battery and cause premature damage.


147

06/04/27 10:46:09 31HM3740_157

Appearance Care

Frequent cleaning and polishing will keep your Honda looking newer longer.

Frequent cleaning also identifies you as an owner who values his ATV.

A clean ATV is also easier to inspect and service.

General Recommendations


To clean your ATV, you may use:

− water

− a mild, neutral detergent and water

− a mild spray and wipe cleaner/polisher

− a mild spray and rinse cleaner/degreaser and water

Avoid products that contain harsh detergents or chemical solvents that could damage the metal, paint, and plastic on your ATV.

If your ATV is still warm from recent operation, give the engine and exhaust system time to cool off.

Park in a shady area. Washing your ATV in bright sunlight may cause the finish to fade because water droplets intensify the sun’s brightness.

Spotting is also more likely because surface water can dry before you have time to wipe it off.

Clean your ATV regularly to protect surface finishes.

We recommend the use of a garden hose to wash your ATV. High pressure washers (like those at coin-operated car washers) can damage certain parts of your ATV.

High pressure water (or air) can damage certain parts of your ATV.

After cleaning, inspect for damage, wear, and leaks (fuel, oil and brake fluid).

148


06/04/27 10:46:18 31HM3740_158

Appearance Care

Washing Your ATV with a Mild Detergent


1.

2.

Rinse your ATV thoroughly with cool water to remove loose dirt.

Fill a bucket with cool water. Mix in a mild, neutral detergent, such as dish washing liquid or a product made especially for washing motorcycles or automobiles.

3.

Wash your ATV with a sponge or soft towel. As you wash, check for heavy grime. If necessary, use a mild cleaner/degreaser to remove the

4.

grime.

After washing, rinse your ATV thoroughly with plenty of clean water

5.

to remove any residue. Detergent residue can corrode alloy parts.

Dry your ATV with a chamois or a soft towel. Leaving water on the

6.

surface to air dry can cause dulling and water spots. As you dry, inspect for chips and scratches.

Start the engine and let it idle for several minutes. The engine heat will help dry moist areas.

7.

As a precaution, ride your ATV at a slow speed and apply the brakes several times. This will help dry the brakes and restore normal braking performance.

If the inside of the headlight lens appears clouded immediately after washing, it should clear after a few minutes of riding.


149

06/04/27 10:46:28 31HM3740_159

Appearance Care

Spray Cleaning Your ATV


Avoid using spray cleaner products on the tires or suspension components.

Suggestions for using spray cleaner(s) follow:

ATV condition

Dust and fingerprint smudges.

Light road grimes.

Heavy grime. Oil leaks.

Brake dust.

Dull, corroded chrome or aluminum.

Recommended Cleaning

Apply a spray cleaner/polish and wipe paint, chrome, glass, and clear plastic.

Spray any difficult-to-reach or very dirty areas with a spray cleaner/ degreaser.

Rinse and dry.

Apply a spray cleaner/polish and wipe with a non-abrasive cloth.

Use a spray cleaner/degreaser. If necessary, rub with a sponge.

Rinse and dry.

Apply a spray cleaner/polish and wipe with a non-abrasive cloth.

Apply a high quality chrome/ aluminum polish and wipe with a non-abrasive cloth.

150


06/04/27 10:46:32 31HM3740_160

Appearance Care

Aluminum Wheel Maintenance


Aluminum may corrode from contact with dirt, mud, or road salt. Clean the wheels after riding through any of these substances. Use a wet sponge and mild detergent. Avoid stiff brushes, steel wool, or cleaners containing abrasives or chemical compounds.

After washing, rinse with plenty of water and dry with a clean cloth.

Then apply a mild, commercially-available spray cleaner/polish or wax.

For stained or dull-looking wheels, use a quality chrome/aluminum polish to restore the finish.


151

06/04/27 10:46:38 31HM3740_161

Appearance Care

Finishing Touches


After washing your ATV, consider using a commercially-available spray cleaner/polish or quality liquid or paste wax to finish the job. Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Apply the polish or wax according to the instructions on the container.

If a surface on your ATV is chipped or scratched, your Honda dealer has touch-up paint to match your ATV’s color. Be sure to use your

ATV’s color code (page 181 ) when you buy touch-up paint.

If the frame has a chip that exposes the metal, first apply primer (to prevent corrosion) and then apply the touch-up paint. Several thin layers of touch-up paint are better than one thick coat.

152


06/04/27 10:46:41 31HM3740_162

Tips

Here’s helpful advice on how to prepare for an off-road adventure, how to transport and store your Honda, and how to be an environmentally responsible ATV owner.

Preparing for a Ride ...........................................................................

. 154

What to Take to the Riding Area ...................................................

. 154

What to Take on the Trail ..............................................................

. 155

Transporting Your Honda ..................................................................

. 156

Storing Your Honda ...........................................................................

. 158

Preparation for Storage ..................................................................

. 159

Removal from Storage ...................................................................

. 161

You & the Environment .....................................................................

. 162

Tips

153

06/04/27 10:46:50 31HM3740_163

Preparing for a Ride

A safe and enjoyable ride begins with good planning and preparation.

Always ride with at least one other person in case you have trouble, and let someone know where you’re going and when you expect to return.

Before riding in an unfamiliar area, find out in advance if you need special permits, get maps so you can study the terrain, and talk to other riders who know the area. The Forest Service and the Bureau of Land

Management (USA only), the Ministry of Natural Resources (Canada only), riding clubs, and off-road magazines are good sources of information.

What to Take to the Riding Area

Along with your ATV and riding gear, you should take along some tools and supplies in case you have a problem. For some of the difficulties you might encounter, see Taking Care of the Unexpected, on page 163 .

which begins

We recommend that you always take water, food, a first aid kit, and your owner’s manual. Other items you should consider loading on your truck or trailer include: a tool kit tire repair supplies and tools, and tires extra parts, control levers, cables, and spark plugs wire, duct tape, and rope extra gasoline

For safety, all refueling should be done at a gas station on the way to the riding area or at your base camp.

154

Tips

06/04/27 10:46:54 31HM3740_164

Preparing for a Ride

What to Take on the Trail

What you take with you during a ride depends on the kind of terrain, how long you expect to ride, how far you might go from your base camp or help, and how experienced you or your companions are in making repairs.

If you decide to take some tools, spare parts, or other supplies on the trail, be sure you can carry them safely and know how to use them. Also, be sure to follow the loading guidelines and weight limit (page 35 ).

Tips

155

06/04/27 10:46:59 31HM3740_165

Transporting Your Honda

Do not tow your ATV behind a car or other vehicle.

When you transport your ATV, we recommend that you carry the vehicle in its normal operating position (on all four wheels). Do not incline the vehicle upright on its rear end. This can damage the vehicle, and leaking gasoline could be a hazard.

Follow these procedures:

1.

Set the parking brake and place the transmission in gear.

2.

Turn the fuel valve OFF.

156

Tips

06/04/27 10:47:07 31HM3740_166

Transporting Your Honda

3.

Secure the vehicle with ‘‘tie-down straps’’ in the areas shown.

Suitable ‘‘tie-down straps’’ are available from your Honda dealer.

4.

Ordinary rope is not recommended because it can stretch under load.

Using ‘‘tie-down straps’’ in any other areas can damage your ATV.

Rock the vehicle back and forth to make sure the ‘‘tie-down straps’’ are tight and the vehicle is secure.

(1)

(4)

(2)

(3)

(1) front carry pipe

(2) right footpeg

(3) left footpeg

(4) rear carry pipe or rear axle shaft

Tips

157

06/04/27 10:47:11 31HM3740_167

Storing Your Honda

If you won’t be riding for an extended period, such as during the winter, thoroughly inspect your ATV and correct any problem before storing it.

That way, needed repairs won’t be forgotten and it will be easier to get your ATV running again.

For more information about storage, refer to the Honda Motorcycle

Winter Storage Guide, available from your Honda dealer (USA only).

We suggest you perform the following procedures to keep your ATV in top condition. These storage procedures will reduce the deterioration that can occur during storage.

158

Tips

06/04/27 10:47:19 31HM3740_168


Preparation for Storage


This procedure requires a means for draining and disposing of drained fuel (page 162 ).

1.

2.

Change the engine oil and filter (page 96 ).

3.

4.

Fill the fuel tank. Make sure the fuel fill cap is properly installed.

Make sure the fuel valve is OFF.

Drain the carburetor into an approved gasoline container and dispose of it in an approved manner (page 162 ).

If storage will last longer than one month, carburetor draining is important, to assure proper performance after storage.

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when handling fuel.

Stop the engine and keep heat, sparks and flame away.

Handle fuel only outdoors.

Wipe up spills immediately.

(cont’d)

Tips

159

06/04/27 10:47:28 31HM3740_169


5.

To prevent rusting in the cylinders, perform the following:

Remove the spark plug cap from the spark plug.

Remove the spark plug.

Do not connect the spark plug to the spark plug cap.

Pour a tablespoon (15 − 20 cc) of clean engine oil into cylinder and cover the spark plug hole with a piece of cloth.

With the engine stop switch in the RUN ( ) position, press the

6.

start button several times to crank the engine and distribute the oil.

Reinstall the spark plug and spark plug cap.

Remove the battery and charge it fully. Store it in an area protected from freezing temperatures and direct sunlight. Slow charge the battery (page 147 ) once a month.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

7.

Wash and dry your ATV. Wax all painted surfaces.

8.

Lubricate the drive chain (page 141 ).

160

Tips

06/04/27 10:47:38 31HM3740_170


9.

10.

Inflate the tires to their recommended pressures (page 129 ).

Store your ATV in an unheated area, free of dampness, away from sunlight, with a minimum of daily temperature variation.

11.

Place your ATV on blocks to lift all tires off the floor.

12.

Cover your ATV with a porous material. Avoid using plastic or similar non-breathing, coated materials that restrict air flow and allow heat and moisture to accumulate.

Removal from Storage


1.

2.

3.

Uncover and clean your ATV.

If your ATV has been stored for more than four months − change the engine oil (page 96 ).

If your ATV has been stored for more than two months − ask your

4.

5.

6.

Honda dealer to drain and replace the fuel.

Charge the battery (page 147 ) as required. Install the battery.

Lubricate the drive chain (page 141 ).

Perform a pre-ride inspection (page 32 ), then test-ride your ATV at low speeds.

Tips

161

06/04/27 10:47:44 31HM3740_171

You & the Environment

Owning and riding an ATV can be enjoyable, but you must do your part to protect nature. When you show respect for the land, wildlife, and other people, you also help preserve the sport of off-road riding.

Following are tips on how you can be an environmentally-responsible

ATV owner.

Tread Lightly.

Stay on existing roads and trails, avoid surfaces that are easily damaged, and ride only in areas approved for off-road vehicles.

Keep the Noise Down.

Loud vehicles can be offensive. Ride as quietly as possible, don’t remove your spark arrester, and don’t modify the muffler or any other part of your air intake and exhaust systems. Such modifications not only increase noise, they also reduce engine performance and may be illegal.

Choose Sensible Cleaners.

Use a biodegradable detergent when you wash your ATV. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Don’t throw cleaning solvents away; see the following guidelines for proper disposal.

Recycle Wastes.

It’s illegal and thoughtless to put used engine oil in the trash, down a drain, or on the ground. Used oil, gasoline, and cleaning solvents contain poisons that can hurt refuse workers and contaminate our drinking water, lakes, rivers, and oceans. Before changing your oil, make sure you have the proper containers. Put oil and other toxic wastes in separate sealed containers and take them to a recycling center. Call your local or state office of public works or environmental services to find a recycling center in your area, and to get instructions on how to dispose of non-recyclable wastes.

162

Tips

06/04/27 10:47:48 31HM3740_172

Taking Care of the Unexpected

With all the challenges you can encounter off-road, there’s a chance that sometime something may go wrong. This section gives practical advice to help you deal with a wide range of problems. Take time to read this section before you ride. Also review the tips in Preparing f or a Ride

(page 154 ).

General Guidelines .............................................................................

. 164

If Your Engine Quits or Won’t Start ..................................................

. 166

If You Have a Flat Tire .....................................................................

. 169

If a Fuse Blows ..................................................................................

. 172

If You Crash ........................................................................................

.174

If You Lose Your Key .......................................................................

. 175

If the Battery Is Low (or Dead) ..........................................................

. 176

If a Component Fails ..........................................................................

. 177


163

06/04/27 10:47:55 31HM3740_173


General Guidelines

Keeping your ATV well-maintained is the best way to reduce the possibility of having a problem while riding. However, problems can arise even with well-maintained machines.

Remember to take along your owner’s manual, the tool kit that came with your ATV, and any other items (such as tire repair supplies and additional tools) that might help you solve a problem on your own.

If something goes wrong during a ride, the first thing to do is stop as soon as you safely can. Do not continue riding if you have a flat tire, or you hear an unusual noise, or your ATV just doesn’t feel right. If you continue riding, you could cause more damage and endanger your own safety.

After a stop, take time to assess the situation. Carefully inspect your

ATV to identify the problem, then consider your options before you decide what to do.

If a problem is relatively minor and you have the tools, supplies, and skills to make a permanent repair, you may be able to fix it on the trail and continue riding. Or, you may be able to make a temporary repair that allows you to slowly ride back to your base where you can make a permanent repair or get help.

When a problem is more serious − or you don’t have the tools, supplies, experience, or time to deal with it − you need to choose the safest way to get yourself and your ATV back to base. For example, if you are close enough, you (or you and another person) might be able to push it back.

164


06/04/27 10:48:01 31HM3740_174


Should you ever have a problem while riding, please follow these guidelines:

Always put personal safety first.

Take time to assess the situation and your options before deciding what to do.

If the problem is relatively minor and you have the tools, supplies, and skills to make a temporary repair, be sure to have permanent repairs made as soon as possible.

Do not continue riding if you are hurt or your ATV is not in safe riding condition.

Additional recommendations for specific problems follow.


165

06/04/27 10:48:05 31HM3740_175

If Your Engine Quits or Won’t Start

Proper operation and maintenance can prevent starting and engine performance problems. In many cases, the cause of the problem may be a simple operational oversight.

If you have a problem starting the engine − or experience poor engine performance − the following information may help you. If you can’t correct the problem, see your Honda dealer.

If your ATV won’t start, listen as you press the start button. If you don’t hear the starter motor turning, refer to the Starter motor doesn’t operate symptom. If you can hear the starter motor working normally, refer to the Starter motor works, but the engine won’t start symptom.

166


06/04/27 10:48:24 31HM3740_176


SYMPTOM: Starter motor doesn’t operate.

POSSIBLE CAUSE ignition switch OFF

WHAT TO DO

Turn the ignition switch ON.

Turn the engine stop switch to RUN.

engine stop switch

OFF transmission not in neutral blown fuse

Shift into neutral.

battery lead loose low (or dead) battery faulty starter motor

Replace with a new fuse of the same rating (page 172 ).

Tighten the battery lead.

Charge the battery (page 147 ).

If charging doesn’t help, see your

Honda dealer.

If all possible causes are negative, the starter motor may be faulty. See your Honda dealer.

SYMPTOM: Starter motor works, but the engine won’t start.

WHAT TO DO POSSIBLE CAUSE out of fuel flooded engine loose or unconnected spark plug cap loose battery cables weak battery

Fill the fuel tank.

See

F looded Engine

(page 51 ).

Install the spark plug cap securely. If the engine still won’t start, see your

Honda dealer.

Tighten the battery terminal bolts.

Charge the battery (page 147 ). If charging doesn’t help, see your

Honda dealer.


167

06/04/27 10:48:37 31HM3740_177


SYMPTOM: Engine starts, but runs poorly.

POSSIBLE CAUSE idles roughly, too

WHAT TO DO

Check engine idle adjustment (page fast, stalls poor engine performance at altitudes above

3,000 feet.

runs erratically, misfires blubbers

(rich fuel mixture) sooty exhaust

(rich fuel mixture) detonates or pings under load

110 ). If the problem persists, see your Honda dealer.

Ask your Honda dealer to modify the carburetion with a high altitude jet.

Refer to

High Altitude Car bur etor

Adjustment,

page 187 .

See your Honda dealer.



If applicable, switch to the recommended octane gasoline

(page 87 ) or change your brand of gasoline. If the problem persists, see your Honda dealer.


afterfires

(backfires) pre-ignition

(runs on after ignition switched OFF)


168


06/04/27 10:48:44 31HM3740_178

If You Have a Flat Tire

How you handle a flat tire on the trail depends on how serious the tire damage is, and what tools and supplies you have with you.

If you have a slow leak or a minor puncture, use the plug method to make a temporary repair. (The plug method is applied from the outside of the tire and is the same as that for conventional tubeless tires.)

A plug-type repair kit, available at most auto parts stores or service stations, provides a plug, an installation tool, tire cement, and an instruction sheet. Follow the instructions provided with the repair kit to make a temporary repair.

As soon as possible, have the tire permanently repaired by your Honda dealer. Any tire that cannot be repaired should be replaced.

Whenever the ATV is to be operated far from service facilities or available transportation, we recommend that you carry a tire pump and a repair kit with the vehicle.

If the leak is more serious, or a temporary repair doesn’t hold, the tire must be replaced. The tire will also need to be replaced if it is damaged

(page 133 ). Replacing a tire involves removing and re-installing the wheel (page 170 ).

If you are unable to repair a flat tire on the trail, you will need to send for help. We strongly recommend that you do not try to ride with a flat tire. The ATV will be hard to handle, and if the tire comes off the rim, it may lock up the wheel and cause you to crash.


169

06/04/27 10:48:53 31HM3740_179


Emergency Wheel Removal/Installation


(1)

(1)

(1) wheel nuts

(2)

(2) wheel rim

Removal

1.


2.

Raise the front (or rear) wheels off the ground and place a support block under the vehicle.

3.

4.

Remove the wheel.

Avoid getting grease, oil, or dirt on the disc or pad surfaces when removing and installing each wheel. Any contamination can cause poor brake performance or rapid pad wear after reassembly.

170


06/04/27 10:48:59 31HM3740_180


Installation

1.

Position the wheel.

2.

Position the wheel nuts so that the tapered sides face the wheel rim

3.

Tighten the wheel nuts in a crisscross (rather than a circular) pattern to the specified torque:

47 lbf·ft (64 N·m , 6.5 kgf·m)

If a torque wrench was not used for installation, see your Honda dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capability.


171

06/04/27 10:49:06 31HM3740_181

If a Fuse Blows

All of the electrical circuits on your ATV have fuses to protect them from damage caused by excess current flow (short circuit or overload).

If something electrical on your ATV stops working, the first thing you

Check the fuse before looking elsewhere for another possible cause of the problem. Replace a blown fuse and check component operation.

(1)

(1) blown fuse

The fuse is located near the air cleaner case cover behind the seat.

Recommended Fuses main fuse 15A

172


06/04/27 10:49:14 31HM3740_182

To replace the fuse

UNDER SEAT

If a Fuse Blows

(3)

(1)

(2)

(1) fuse

(2) spare fuse

(3) fuse case cover

1.

2.

3.

To prevent an accidental short circuit, turn the ignition switch OFF

( ) before checking or replacing the fuse.

To access the fuse ( ), remove the seat (page 86 ).

4.

5.

6.

Replace the old fuse.

Reinstall the fuse case cover.

Install the seat.


173

06/04/27 10:49:19 31HM3740_183

If You Crash

Personal safety is your first priority after an accident. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. If you cannot ride safely, send someone for help. Do not ride if you will risk further injury.

If you decide you are capable of riding safely, carefully inspect your

ATV for damage and determine if it is safe to ride. Check the tightness of critical nuts and bolts securing such parts as the handlebar, control levers, brakes, and wheels.

If there is minor damage, or you are unsure about possible damage but decide to try riding the ATV back to your base, ride slowly and cautiously.

Sometimes, crash damage is hidden or not immediately apparent. When you get home, thoroughly check your ATV and correct any problems you find. Also, be sure to have your Honda dealer check the frame and suspension after any serious crash.

174


06/04/27 10:49:23 31HM3740_184

If You Lose Your Key at the rear of the manual. You’ll need this number to have a duplicate key made.

If you lose your key and aren’t carrying a duplicate, either get your spare or have one made. If you don’t know your key number, call the dealer you purchased your Honda from. They may have it listed in their records. If they don’t, transport your ATV to them or the nearest Honda dealer. The dealer will probably have to remove the ignition switch assembly to find the key number so they can make a key for you.

(1) key number

(1)


175

06/04/27 10:49:28 31HM3740_185

If the Battery Is Low (or Dead)

Jump starting is not recommended, especially if you use an automobile battery. The greater amperage of an automobile battery when the car engine is running can damage your ATV’s electrical system.

Bump starting is also not recommended.

If you can’t charge the battery or it appears unable to hold a charge, contact your Honda dealer.

176


06/04/27 10:49:33 31HM3740_186

If a Component Fails

The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Making a trailside repair depends on how serious the damage is and what tools and supplies you have with you.

If any component of the brake system is damaged, you may be able to ride carefully back to your base using the other brake components for slowing or stopping.

If you damage a throttle cable or other critical component, your ATV may be unsafe to ride. Carefully assess the damage and make any repairs that you can. But if there is any doubt, it’s best to be conservative and safe.


177

06/04/27 10:49:35 31HM3740_187

178


06/04/27 10:49:39 31HM3740_188

Technical Information

This section contains dimensions, capacities, and other technical data, plus information on government requirements and how to break-in your

ATV.

Vehicle Identification .........................................................................

. 180

Specifications .....................................................................................

. 182

Break-in Guidelines ...........................................................................

. 186

High Altitude Carburetor Adjustment ................................................

. 187

Emission Control Systems ..................................................................

. 188

Oxygenated Fuels ...............................................................................

. 192


179

06/04/27 10:49:45 31HM3740_189

Vehicle Identification

Serial Numbers

The VIN and engine serial numbers and key number may be required when ordering replacement parts. You may record these numbers in the

Quick Reference section at the rear of this manual.

FRONT

(1)

(1) VIN

RIGHT SIDE

(2)

(2) engine number

180


06/04/27 10:49:51 31HM3740_190

Vehicle Identification

Color Label & Code

seat (page 86 ) to check the label.

The color code is helpful when ordering replacement parts. You may record the color and code in the Quick Reference section at the rear of this manual.

UNDER SEAT

(1)

(1) color label


181

06/04/27 10:50:04 31HM3740_191

Specifications

Dimensions overall length overall width overall height wheelbase ground clearance

Fuel & Lubricants fuel recommendation fuel tank capacity fuel tank reserve engine oil capacity engine oil recommendation

67.7 in (1,720 mm)

43.5 in (1,105 mm)

41.9 in (1,063 mm)

45.1 in (1,145 mm)

4.6 in (117 mm) unleaded gasoline, pump octane number of 86 or higher

2.25 US gal (8.5 ) including reserve

0.48 US gal (1.8 ) after disassembly:

2.1 US qt (2.0 ) after draining:

1.69 US qt (1.60 )

API Service Classification SG or higher except oils labeled as energy conserving on the circular API service label, SAE 10W-30, JASO T

903 standard MA,

Pro Honda GN4 4-stroke oil (USA &

Canada) or Honda 4-stroke oil

(Canada only), or an equivalent motorcycle oil

182


06/04/27 10:50:29 31HM3740_192

Specifications

Capacities passenger capacity maximum weight capacity operator only

270 lbs (120 kg) rider, all cargo and accessories

Engine Specifications displacement bore & stroke compression ratio spark plug

(standard) spark plug

(cold climate) spark plug

(high speed riding) spark plug gap valve clearance

(cold) idle speed

17.18 cu-in (281.7 cm )

2.91

× 2.58 in (74.0

× 65.5 mm)

8.9 : 1

DR8ES-L (NGK)

DR7ES (NGK) or

X24ESR-U (DENSO) or

X22ESR-U (DENSO)

DR8ES (NGK) or

X27ESR-U (DENSO)

0.024

− 0.028 in (0.60

− 0.70 mm)

0.004 in (0.10 mm)

1,400 ± 100 rpm

Power Transmission primary reduction final reduction

1st gear ratio

2nd

3rd

4th

5th reverse final drive

2.833

2.923

3.692

2.529

1.857

1.458

1.178

5.415

chain

DID520V

RK520 MOZ9 or


183

06/04/27 10:50:47 31HM3740_193

Specifications

Chassis & Suspension caster trail tire size, front tire size, rear tire pressure, front & rear (cold) maximum tire pressure, front & rear (cold) minimum tire pressure, front & rear (cold)

7°

1.2 in (30 mm)

AT 22 × 7-10 ★★

OHTSU P/V 102

AT 22 × 10-9 ★

OHTSU P/V 702

Front:

4.4 psi (30 kPa , 0.30 kgf/cm )

Rear:

2.9 psi (20 kPa , 0.20 kgf/cm )

Front:

4.8 psi (33 kPa , 0.33 kgf/cm )

Rear:

3.3 psi (23 kPa , 0.23 kgf/cm )

Front:

4.0 psi (27 kPa , 0.27 kgf/cm )

Rear:

2.5 psi (17 kPa , 0.17 kgf/cm )

Electrical battery generator

Lights headlight brake/tail light neutral indicator reverse indicator

12V − 8Ah

0.24 kW/5,000 rpm

12V 30/30W

LED

12V 3W

12V 3.4W

× 2

184


06/04/27 10:50:55 31HM3740_194

Specifications

Fuse main 15A

Torque Specification engine oil drain bolt engine oil filter bolt wheel nuts

18 lbf·ft (24 N·m , 2.4 kgf·m)

7 lbf·ft (10 N·m , 1.0 kgf·m)

47 lbf·ft (64 N·m , 6.5 kgf·m)


185

06/04/27 10:50:59 31HM3740_195

Break-in Guidelines

Help assure your ATV’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles

(25 km).

During this period, avoid full-throttle starts and rapid acceleration.

186


06/04/27 10:51:04 31HM3740_196

High Altitude Carburetor Adjustment

At high altitude, the standard carburetor air-fuel mixture will be too rich.

Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting.

Operation at an altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.

High altitude performance can be improved by specific modifications to the carburetor. If you always operate your engine at altitudes above

6,500 feet (2,000 meters), have your servicing dealer perform this carburetor modification. This engine, when operated at high altitude with the carburetor modifications for high altitude use, will meet each emission standard throughout its useful life.

Even with carburetor modification, engine horsepower will decrease about 3.5% for each 1,000-foot (300-meter) increase in altitude. The effect of altitude on horsepower will be greater than this if no carburetor modification is made.

When the carburetor has been modif ied f or high altitude operation, the air-f uel mixture will be too lean f or low altitude use. Operation at altitudes below 5,000 f eet (1,500 meters) with a modif ied carburetor may cause the engine to overheat and result in serious engine damage.

For use at low altitudes, have your servicing dealer return the carburetor to original f actory specif ications.


187

06/04/27 10:51:09 31HM3740_197

Emission Control Systems

Exhaust Emission Requirements (USA only)

The U.S. Environmental Protection Agency (EPA) and the California

Air Resources Board (CARB) require that your ATV comply with applicable exhaust emission standards during its useful life, when operated and maintained according to the instructions provided.

right side of the frame.

FRONT

(1)

(1) vehicle emission control infomation label

188


06/04/27 10:51:14 31HM3740_198


Source of Exhaust Emissions

The combustion process produces carbon monoxide (CO), oxides of nitrogen (NOx) and hydrocarbons (HC). Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight.

Carbon monoxide does not react in the same way, but it is toxic.

Honda Motor Co., Ltd. utilizes various systems to reduce carbon monoxide, oxides of nitrogen and hydrocarbons.

Exhaust Emission Control System

The exhaust emission control system is composed of appropriate carburetor settings. No adjustments should be made except for an idle speed adjustment with the throttle stop screw or carburetor adjustment for high altitude operation.

The exhaust emission control system is separate from the crankcase emission control system.


189

06/04/27 10:51:21 31HM3740_199


Crankcase Emission Control System

The engine is equipped with a closed crankcase system to prevent discharging crankcase emissions into the atmosphere. Blow-by gas is returned to the combustion chamber through the air cleaner and the carburetor.

Problems That May Affect ATV Exhaust Emissions

If you are aware of any of the following symptoms, have the vehicle inspected and repaired by your Honda ATV dealer.

Symptoms:

1.

2.

3.

4.

Hard starting or stalling after starting

Rough idle

Misfiring or backfiring during acceleration

After-burning (backfiring)

5.

Poor performance (driveability) and poor fuel economy

Federal regulations prohibit removing or disabling a device or element of design that may affect your engine’s emission performance unless your ATV will be used exclusively in competition. If you modify your engine for use in sanctioned competition events, you must deface or destroy the emission control information label.

190


06/04/27 10:51:27 31HM3740_200


Noise Emission Control System

TAMPERING WITH THE NOISE CONTROL SYSTEM IS

PROHIBITED:

State laws prohibit, or Canadian provincial laws may prohibit the inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or the vehicle after such device or element of design has been removed or rendered inoperative by any person.

AMONG THOSE ACTS PRESUMED TO CONSTITUTE

TAMPERING ARE THE FOLLOWING ACTS:

1.

Removal of, or puncturing the muffler, baffles, header pipes or any other component which conducts exhaust gases.

2.

3.

4.

Removal of, or puncturing of any part of the intake system.

Lack of proper maintenance.

Replacing any moving parts of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the manufacturer.


191

06/04/27 10:51:33 31HM3740_201

Oxygenated Fuels

Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and

Canada use oxygenated fuels to help reduce emissions.

If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.

Before using an oxygenated fuel, try to confirm the fuel’s contents.

Some states/provinces require this information to be posted on the pump.

The following are the EPA-approved percentages of oxygenates:

ETHANOL (ethyl or grain alcohol) 10% by volume

You may use gasoline containing up to 10% ethanol by volume.

Gasoline containing ethanol may be marketed under the name

‘‘Gasohol’’.

MTBE (Methyl Tertiary Butyl Ether) 15% by Volume

You may use gasoline containing up to 15% MTBE by volume.

METHANOL (methyl or wood alcohol) 5% by Volume

You may use gasoline containing methanol containing up to 5% methanol by volume as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also damage metal, rubber, and plastic parts of your fuel system.

192


06/04/27 10:51:37 31HM3740_202

Oxygenated Fuels

If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.

Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates mentioned above are not covered under warranty.

Oxygenated fuels can damage paint and plastic. Be careful not to spill fuel when filling the fuel tank. Wipe up any spills immediately.

Oxygenated f uels can damage paint and plastic. Damage caused by spilled f uel is not covered by warranty.


193

06/04/27 10:51:40 31HM3740_203

194


06/04/27 10:51:43 31HM3740_204

Consumer Information

This section contains information on your warranty and how to get an official Honda service manual.

Authorized Manuals ...........................................................................

. 196

Warranty Coverage ............................................................................

. 199

Warranty Service ................................................................................

. 200

Contacting Honda ..............................................................................

. 201

Your Honda Dealer ............................................................................

. 202

The Honda Rider’s Club (USA only) .................................................

. 203


195

06/04/27 10:51:50 31HM3740_205

Authorized Manuals

The Service Manual used by your authorized Honda dealer is available from Helm, Inc. (USA only, Canada: See your Honda dealer to order authorized manuals.)

Also available but not necessary to service your model is the Honda

Common Service Manual which explains theory of operation and basic service information for various systems common to all Honda motorcycles, motor scooters and ATVs.

These Honda manuals are written for the professional technician, but most mechanically-capable owners should find them easy to use if they have the proper tools and observe proper safety standards.

Special Honda tools are necessary for some procedures.

Publication Item No.

Description Price Each ＊

61HM360

61CM002

2007 TRX300EX Service Manual

Common Service Manual

$40.00

$48.00

31HM3740 2007 TRX300EX Owner’s Manual

＊ Prices are subject to change without notice and without incurring obligation.

$16.00

196


06/04/27 10:51:59 31HM3740_206

Order On-Line: www.helminc.com

Order Toll Free: 1-888-CYCLE93 (1-888-292-5393)

(NOTE: For Credit Card Orders Only)

Monday − Friday 8:00 AM − 6:00 PM EST

OR

By completing this form you can order the materials desired. You can pay by check or money order, or charge to your credit card. Mail to

Helm, Inc. at the address shown on the back of this order form (USA only).

Canada: See your Honda dealer to order authorized manuals.

Publication

Item No.

Item Description Qty.

Price Each ＊ Total Price

＊ Prices are subject to change without notice and without incurring obligation.

Orders are mailed within 10 days. Please allow adequate time for delivery.

Sub Total

Purchaser’s Sales Tax

Mich. Add 6 %

Calif. Add 8.25 %

Handling Charge

Grand Total

$5.00


197

06/04/27 10:52:13 31HM3740_207

NOTE: Dealers and Companies please provide dealer or company name, and also the name of the person to whose attention the shipment should be sent.

S

H

I

P

T

O

Customer Name

Attention

Street Address

City

Daytime Telephone Number

( )

State

Apartment Number

Zip Code

Check or money order enclosed payable to Helm Inc. U. S. funds only. Do not send cash.

E

N

T

P

A

Y

M

Check here if your billing address is different from the shipping address shown above.

VISA

Account Number

MasterCard Discover

Expiration: Mo. Yr.

−

Customer Signature Date

These Publications cannot be returned for credit without receiving advance authorization within 14 days of delivery. On returns, a restocking fee may be applied against the original order.

HELM P. O. BOX 07280, DETROIT, MICHIGAN 48207

198


06/04/27 10:52:19 31HM3740_208

Warranty Coverage

Your new Honda is covered by these warranties:

TRX Limited Warranty

Exhaust Emission Warranty (USA Only)

There are responsibilities, restrictions, and exclusions which apply to these warranties. Please read the Warranties Booklet given to you by your Honda dealer at the time of purchase. Be sure to keep your Honda owner’s card with your Warranties Booklet (USA only).

It is important to realize that your warranty applies to defects in material or workmanship of your Honda. Your warranty coverage does not apply to normal wear or deterioration associated with using the ATV.

Your warranty coverage will not be voided if you choose to perform your own maintenance. However, you should have the proper tools and service information and be mechanically qualified. Failures that occur due directly to improper maintenance are not covered.

Almost all of your warranty coverage can be extended through the

Honda Protection Plan (USA only). For more information, see your

Honda dealer.


199

06/04/27 10:52:24 31HM3740_209

Warranty Service

Please remember that recommended maintenance interval servicing is not included in your warranty coverage. Additionally, your warranty does not apply to the normal wear of items (such as brakes, tires, etc.).

If you believe you have a problem with your ATV, call the service department of your Honda dealer. Make an appointment for an inspection and diagnosis. Remember, as the owner of the ATV, you will be asked to authorize that inspection. Your dealer will give you the results of the inspection. If the problem is covered under warranty, your dealer will perform the warranty repairs for you.

If you have questions about warranty coverage or the nature of the repair, it is best to talk to the service manager of your Honda dealer.

Sometimes, in spite of the best intentions of all concerned, a misunderstanding may occur. If you aren’t satisfied with your dealer’s handling of the situation, we suggest you discuss your problem with the appropriate member of the dealership’s management team. If the problem has already been reviewed with the Service Manager, Parts

Manager, Sales Manager, etc., contact the Owner of the dealership or their designated representative.

200


06/04/27 10:52:30 31HM3740_210

Contacting Honda

Your owner’s manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner’s manual can be answered by your Honda dealer. If your dealer doesn’t have the answer right away, they will get it for you.

If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That’s why it’s important to work to resolve any differences at the dealership level.

If you wish to comment on your experiences with your Honda or with your dealer, please send your comments to the following address (USA only):

Motorcycle Division, American Honda Motor Co., Inc., P.O. Box 2220,

Torrance, CA 90509-2220, mailstop: 100-4C-7B, telephone: (866) 784-

1870.

Canada: Refer to the Warranties Booklet that was supplied with your vehicle.

Please include the following information in your letter: name, address, and telephone number product model, year, and VIN date of purchase dealer name and address

We will likely ask your Honda dealer to respond, or possibly acknowledge your comments directly.


201

06/04/27 10:52:36 31HM3740_211

Your Honda Dealer

Once you purchase your new Honda, get familiar with the organization of your Honda dealer so you can utilize the full range of services available.

The service department is there to perform regular maintenance and unexpected repairs. It has the latest available service information from

Honda. The service department will also handle warranty inspections and repairs.

The parts department offers Genuine Honda parts, Pro Honda products,

Hondaline accessories (USA only), and Honda accessories and products

(Canada only). The same quality that went into your Honda can be found in Genuine Honda replacement parts. You’ll also find comparable quality in the accessories and products available from the parts department.

The sales department offers the Honda Protection Plan to extend almost all of your warranty coverage (USA only).

Your Honda dealer can inform you about competition and other riding events in your area. You’ll also find that your dealer is a source of information about American Honda’s Rider Education Centers and the

Honda Rider’s Club of America (USA only).

We’re sure you’ll be as pleased with the service your Honda dealer continues to provide after the sale as you are with the quality and dependability of your Honda.

202


06/04/27 10:52:44 31HM3740_212

The Honda Rider’s Club (USA only)

One of the best ways to get the most enjoyment from owning and riding your Honda is through the Honda Rider’s Club of America. Your purchase of a new motorcycle, scooter, ATV or PWC from a participating U.S. Honda dealer entitles you to a complimentary oneyear membership in the Club. There are hundreds of HRCA Chaptersponsoring dealers across the USA with events and activities almost every weekend. Membership benefits include:

24-hour, toll-free roadside assistance for your new Honda (includes roadside assistance for your transport vehicle [up to one ton] as long as your Honda is aboard or in tow).

For street-legal motorcycles and scooters only.

An exclusive HRCA website complete with access to the official

Honda Common Service Manual, contests, insider information and more.

Reimbursement (up to $75) for successful completion of a

Motorcycle Safety Foundation training course. Separate, complimentary training from the Specialty Vehicle Institute of

America for purchasers of new ATVs.

One full year of Honda Red Rider magazine (six issues).

Discounts from HRCA partners for experienced rider courses.

Discounted vehicle insurance from the HRCA’s insurance partner.

Racing contingency programs and assistance at selected dual-sport, off-road and motocross events for off-road motorcycles and selected

ATVs.

If you purchased an of f -road motorcycle, ATV or PWC, your benef its do not include roadside assistance or trip interruption protection.

Contact your Honda dealer for more information or call: 1-800-847-

4722 or log on to www.hrca.honda.com.


203

06/04/27 10:52:48 31HM3740_213

Table of Contents

The following presents the contents of each section of your owner’s manual.

ATV SAFETY ......................................................................................

. 1

Important Safety Information ................................................................

. 2

Safety Labels ..........................................................................................

. 5

INDICATORS & CONTROLS ...........................................................

. 9

Operation Component Locations .........................................................

. 11

Indicators ..............................................................................................

. 14

Reverse and Neutral Indicators ........................................................

. 14

204


06/04/27 10:52:52 31HM3740_214


Controls & Features .............................................................................

. 15

Fuel Valve ........................................................................................

. 15

Choke Lever .....................................................................................

. 16

Ignition Switch .................................................................................

. 17

Start Button ......................................................................................

. 18

Engine Stop Switch ..........................................................................

. 18

Headlight Switch ..............................................................................

. 19

Headlight Dimmer Switch ................................................................

. 19

Throttle Lever ..................................................................................

. 20

Clutch Lever/Parking Brake Lever ..................................................

. 20

Reverse Assist Lever ........................................................................

. 21

Front Brake Lever ............................................................................

. 22

Rear Brake Pedal ..............................................................................

. 22

Parking Brake ....................................................................................

.23

Flag Pole Bracket .............................................................................

. 24

BEFORE RIDING .............................................................................

. 25

Are You Ready to Ride ?

.....................................................................

. 26

Protective Apparel ............................................................................

. 26

Rider Training ..................................................................................

. 28

Age Recommendation ......................................................................

. 29

No Passengers ..................................................................................

. 29

No Alcohol or Drugs ........................................................................

. 30

Is Your ATV Ready to Ride ?

..............................................................

. 31

Pre-ride Inspection ...........................................................................

. 31

Load Limits & Guidelines ....................................................................

. 34

Loading ............................................................................................

. 34

Load Limits ......................................................................................

. 35

Loading Guidelines ..........................................................................

. 36

Accessories & Modifications ...............................................................

. 37

Accessories .......................................................................................

. 37

Modifications ...................................................................................

. 38


205

06/04/27 10:52:55 31HM3740_215


BASIC OPERATION & RIDING ....................................................

. 39

Safe Riding Precautions .......................................................................

. 41

Off-Road Use Only ..........................................................................

. 41

Keep Hands and Feet on Controls ....................................................

. 42

Control Speed ...................................................................................

. 43

Use care on Unfamiliar or Rough Terrain ........................................

. 44

Do Not Perform Stunts .....................................................................

. 45

Starting & Stopping the Engine ...........................................................

. 46

Preparation .......................................................................................

. 47

Starting Procedure ............................................................................

. 48

Flooded Engine ................................................................................

. 51

How to Stop the Engine ...................................................................

. 51

Shifting Gears ......................................................................................

. 52

Riding in Reverse .................................................................................

. 54

Braking .................................................................................................

. 56

Riding Your ATV ................................................................................

. 58

Making Turns ...................................................................................

. 58

Skidding or Sliding ..........................................................................

. 60

Riding Up Hills ................................................................................

. 61

Riding Down Hills ...........................................................................

. 65

Crossing or Turning on Hills or Slopes ............................................

. 66

Riding Over Obstacles .....................................................................

. 68

Riding Through Water .....................................................................

. 69

Parking .................................................................................................

. 70

206


06/04/27 10:53:04 31HM3740_216


SERVICING YOUR HONDA ...........................................................

. 71

Bef ore You Service Your Honda

The Importance of Maintenance ..........................................................

. 73

Maintenance Safety ..............................................................................

. 74

Important Safety Precautions ...........................................................

. 75

Maintenance Schedule .........................................................................

. 76

Maintenance Record .............................................................................

. 80

Service Preparations

Maintenance Component Locations .....................................................

. 81

Tool Kit ................................................................................................

. 84

Owner’s Manual Storage ......................................................................

. 85

Seat Removal .......................................................................................

. 86

Service Procedures

Fluids & Filters

Fuel ......................................................................................................

. 87

Engine oil & Filter ...............................................................................

. 92

Air Cleaner ...........................................................................................

. 99

Engine

Throttle ...............................................................................................

. 103

Clutch System ....................................................................................

. 105

Reverse Lock System .........................................................................

. 109

Engine Idle Speed ..............................................................................

. 110

Spark Plug ..........................................................................................

. 111

Valves .................................................................................................

. 114

Spark Arrester ....................................................................................

. 115

(cont’d)


207

06/04/27 10:53:09 31HM3740_217


Chassis

Suspension .........................................................................................

. 116

Brakes .................................................................................................

. 119

Tires ...................................................................................................

. 128

Engine Guard & Skid Plates ...............................................................

. 135

Drive Chain ........................................................................................

. 136

Electrical

Battery ................................................................................................

. 143

Appearance Care ................................................................................

. 148

TIPS ...................................................................................................

. 153

Preparing for a Ride ...........................................................................

. 154

What to Take to the Riding Area ...................................................

. 154

What to Take on the Trail ..............................................................

. 155

Transporting Your Honda ..................................................................

. 156

Storing Your Honda ...........................................................................

. 158

Preparation for Storage ..................................................................

. 159

Removal from Storage ...................................................................

. 161

You & the Environment .....................................................................

. 162

TAKING CARE OF THE UNEXPECTED ...................................

. 163

General Guidelines .............................................................................

. 164

If Your Engine Quits or Won’t Start ..................................................

. 166

If You Have a Flat Tire .....................................................................

. 169

If a Fuse Blows ..................................................................................

. 172

If You Crash ........................................................................................

.174

If You Lose Your Key .......................................................................

. 175

If the Battery Is Low (or Dead) ..........................................................

. 176

If a Component Fails ..........................................................................

. 177

208


06/04/27 10:53:14 31HM3740_218


TECHNICAL INFORMATION .....................................................

. 179

Vehicle Identification .........................................................................

. 180

Specifications .....................................................................................

. 182

Break-in Guidelines ...........................................................................

. 186

High Altitude Carburetor Adjustment ................................................

. 187

Emission Control Systems ..................................................................

. 188

Oxygenated Fuels ...............................................................................

. 192

CONSUMER INFORMATION ......................................................

. 195

Authorized Manuals ...........................................................................

. 196

Warranty Coverage ............................................................................

. 199

Warranty Service ................................................................................

. 200

Contacting Honda ..............................................................................

. 201

Your Honda Dealer ............................................................................

. 202

The Honda Rider’s Club (USA only) .................................................

. 203

TABLE OF CONTENTS .................................................................

. 204

INDEX ...............................................................................................

. 210

QUICK REFERENCE


209

06/04/27 10:53:18 31HM3740_219

Index

A accessories ............................................................................................

. 37 age recommendation ............................................................................

. 29 air cleaner, filter ................................................................................................

. 100 housing drain tube ..........................................................................

. 102 air pressure, gauge ................................................................................................

. 84 tire ..................................................................................................

. 130 altitude, high .......................................................................................

. 187

American Honda, contacting ..............................................................

. 195 apparel, protective ................................................................................

. 26 appearance care ..................................................................................

. 148 authorized manuals .............................................................................

. 196

B

Battery ................................................................................................

. 143

Brakes, fluid ................................................................................................

. 119 front brake lever ...............................................................................

. 22 brake pad wear ...............................................................................

. 123 parking ...........................................................................................

. 126 rear brake pedal ................................................................................

. 22 braking .................................................................................................

. 56 break-in guidelines .............................................................................

. 186

210

Index

06/04/27 10:53:22 31HM3740_220

Index

C capacity, fuel ........................................................................................

. 88 carburetor, altitude adjustment ...........................................................

. 187 care, appearance .................................................................................

. 148 chain, drive .........................................................................................

. 136 choke, lever ..........................................................................................

. 16 cleaning, appearance care ...................................................................

. 148 climbing hills ........................................................................................

. 61 clutch system ......................................................................................

. 105 color label ...........................................................................................

. 181 compartment, owner’s manual ................................................................................

. 85 tool kit ..............................................................................................

. 84 component fails ..................................................................................

. 177 consumer information ........................................................................

. 195 crash, if you ........................................................................................

. 174 crossing or turning on hills or slops .....................................................

. 66 customer service .................................................................................

. 201

Index

211

06/04/27 10:53:26 31HM3740_221

Index

D dimmer switch, headlight .....................................................................

. 19 dipstick .................................................................................................

. 95 drive chain ..........................................................................................

. 136

E emission control system .....................................................................

. 188 engine flooded .............................................................................................

. 51 guard ..............................................................................................

. 135 idle speed ........................................................................................

. 110 number ...........................................................................................

. 180 oil .....................................................................................................

. 92 pinging .............................................................................................

. 87 starting ..............................................................................................

. 46 stop switch ........................................................................................

. 18 stopping ............................................................................................

. 51 won’t start ......................................................................................

. 166 environment .......................................................................................

. 162 exhaust system cleaning ..........................................................................................

. 115 purging ...........................................................................................

. 115

212

Index

06/04/27 10:53:30 31HM3740_222

Index

F flag pole bracket ...................................................................................

. 24 flat tire ................................................................................................

. 169 flooded engine ......................................................................................

. 51 fuel, fill cap .............................................................................................

. 88 high altitude fuel mixture adjustment .............................................

. 187 oxygenated .....................................................................................

. 192 recommendation ...............................................................................

. 87 refueling ...........................................................................................

. 88 reserve fuel supply ...........................................................................

. 15 tank capacity ....................................................................................

. 88 valve .................................................................................................

. 15 fuse .....................................................................................................

. 172

Index

213

06/04/27 10:53:34 31HM3740_223

Index

G gap, spark plug ...................................................................................

. 112 gasohol ...............................................................................................

. 192 gasoline ................................................................................................

. 87 gear shifting .........................................................................................

. 52

H headlight dimmer switch ......................................................................

. 19 headlight switch ...................................................................................

. 19 high altitude carburetor adjustment ....................................................

. 187 hills, crossing or turning on slops .............................................................

. 67 riding down hills ..............................................................................

. 65 riding up hills ...................................................................................

. 61 stopping on hills ...............................................................................

. 63

Honda, contacting .......................................................................................

. 201

Rider’s Club ...................................................................................

. 203 dealer ..............................................................................................

. 202

Honda service manual ........................................................................

. 198

214

Index

06/04/27 10:53:38 31HM3740_224

Index

I identification, vehicle .........................................................................

. 180 idle speed, engine ...............................................................................

. 110 ignition switch ......................................................................................

. 17 indicators, neutral indicator ...............................................................................

. 14 reverse indicator ...............................................................................

. 14 inspection, pre-ride ...............................................................................

. 31

K key, lost ..................................................................................................

. 175 number ...........................................................................................

. 175 kit, tool .................................................................................................

. 84

Index

215

06/04/27 10:53:42 31HM3740_225

Index

L labels, safety ...........................................................................................

. 5 limit, weight .........................................................................................

. 35 load limits .............................................................................................

. 35 loading guidelines ................................................................................

. 36 lubrication, engine oil ..........................................................................................

. 92 drive chain ......................................................................................

. 141

M maintenance, component locations .........................................................................

. 81 importance ........................................................................................

. 73 precautions .......................................................................................

. 75 record ...............................................................................................

. 80 safety ................................................................................................

. 74 schedule ............................................................................................

. 76 manual, service ...................................................................................

. 198 maximum weight limit .........................................................................

. 34 modifications ........................................................................................

. 38

216

Index

06/04/27 10:53:46 31HM3740_226

Index

N neutral indicator ...................................................................................

. 14 noise emission control systems ..........................................................

. 191 numbers, serial ...................................................................................

. 180

O obstacles, riding over ...........................................................................

. 68 oil, engine .............................................................................................

. 92 operating controls .................................................................................

. 15 operation component locations .............................................................

. 11 owner’s manual storage ........................................................................

. 85 oxygenated fuels ................................................................................

. 192

Index

217

06/04/27 10:53:50 31HM3740_227

Index

P parking .................................................................................................

. 70 passenger, no carrying ......................................................................

. 2, 27 pavement, no riding on ...........................................................................

. 3 pinging, engine .....................................................................................

. 88 plug, spark ..........................................................................................

. 111 pre-ride inspection ................................................................................

. 31 problems, unexpected .........................................................................

. 163 protective apparel .................................................................................

. 26

R removal, seat ...................................................................................................

. 86 reverse, assist cable ......................................................................................

. 109 assist lever ........................................................................................

. 21 gear, shifting into .............................................................................

. 52 indicator ...........................................................................................

. 14 riding in ............................................................................................

. 54 rider training .........................................................................................

. 28

Rider’s Club, Honda ...........................................................................

. 203

218

Index

06/04/27 10:53:55 31HM3740_228

Index riding, basic operations ................................................................................

. 39 clothing .............................................................................................

. 26 precautions .......................................................................................

. 41 preparing for ....................................................................................

. 31 over obstacles ...................................................................................

. 68 safety ..................................................................................................

. 2 safety precautions .............................................................................

. 41 through water ...................................................................................

. 68

S safety, important precautions .......................................................................

. 75 labels ..................................................................................................

. 5 riding precautions .............................................................................

. 41 schedule, maintenance ..........................................................................

. 76 seat removal .........................................................................................

. 86 serial numbers ....................................................................................

. 180 service, customer .........................................................................................

. 201 manuals ..........................................................................................

. 198 warranty .........................................................................................

. 199

(cont’d)

Index

219

06/04/27 10:53:59 31HM3740_229

Index shifting gears ........................................................................................

. 52 skid plates ...........................................................................................

. 135 skidding or sliding ................................................................................

. 60 spark arrester ......................................................................................

. 115 spark knock ..........................................................................................

. 87 spark plug ...........................................................................................

. 111 specifications ......................................................................................

. 182 stalling on a hill ....................................................................................

. 63 start button ............................................................................................

. 18 starting, engine ...............................................................................................

. 46 troubleshooting ...............................................................................

. 166 stop switch, engine ...............................................................................

. 18 stopping engine ....................................................................................

. 51 storage,

ATV ...............................................................................................

. 161 owner’s manual ................................................................................

. 85 suspension, adjustment ......................................................................................

. 116 spring pre-load ...............................................................................

. 117 switch, brakelight .......................................................................................

. 125 headlight ...........................................................................................

. 19 headlight dimmer .............................................................................

. 19 ignition .............................................................................................

. 17

220

Index

06/04/27 10:54:03 31HM3740_230

Index

T throttle, lever ..........................................................................................

. 20, 103 tires, air pressure .....................................................................................

. 130 flat ..................................................................................................

. 169 replacing .........................................................................................

. 134 repairing .........................................................................................

. 133 specifications ..................................................................................

. 134 thread conditions ............................................................................

. 132 tool kit ..................................................................................................

. 84 training, rider ........................................................................................

. 28 transporting your ATV .......................................................................

. 156 trouble, unexpected ............................................................................

. 163 troubleshooting, starting .....................................................................

. 166 turning, on level ground .................................................................................

. 58 on hills or slopes ...............................................................................

. 67

V valve, fuel .............................................................................................

. 15 valve clearance ...................................................................................

. 114 vehicle identification no. (VIN) .........................................................

. 180

Index

221

06/04/27 10:54:06 31HM3740_231

Index

W warning labels ........................................................................................

. 5 warranty, coverage .........................................................................................

. 199 extended .........................................................................................

. 199 service ............................................................................................

. 200 washing your ATV .............................................................................

. 149 water, riding through ...................................................................................

. 69 weight limit ..........................................................................................

. 35 wheel removal ....................................................................................

. 170

222

Index

06/04/27 10:54:08 31HM3740_232

Memo

223

06/04/27 10:54:11 31HM3740_233

224

Memo

06/04/27 10:54:17 31HM3740_234

Quick Reference

The following is a brief, but important collection of information you need to know about your Honda. You’ll also find space to record important notes.

How To Avoid Costly Repairs

The engine of your Honda can be the most expensive component to repair. Proper maintenance, especially the use of the recommended fluids and filters, prevents premature wear and damage.

Frequent causes of costly repairs are:

Engine oil: insufficient quantity, improper oil.

Air cleaner: dirty, leaking because of improper installation (poor seal).

Record important information on the following page:

Quick Reference

06/04/27 10:54:21 31HM3740_235

Quick Reference

Engine No.

VIN

Ignition Key No.

Color Label

Owner’s Name

Address

City/State

Phone

Dealer’s Name

Address

City/State

Phone

Service Mgr.

Quick Reference

06/04/27 10:54:31 31HM3740_236

Scheduled

Maintenance

Pre-ride Inspection

Fuel/Capacity

Engine Oil

Maximum Weight

Capacity

Quick Reference

Initial: 100 miles (150 km)

Regular: every 600 miles (1,000 km)

Check the following items each time before you ride (page 31 ): engine oil, fuel, tires, drive chain, nuts & bolts, underbody & exhaust system, air cleaner housing drain tube, leaks, loose parts, cables, throttle, brakes, clutch lever, reverse assist lever, indicators, lights, switches, steering.

unleaded gasoline, pump octane number

86 or higher

2.25 US gal (8.5 ) reserve:

0.48 US gal (1.8 )

API Service Classification SG or higher except oils labeled as energy conserving on the circular API service label,

SAE 10W-30, JASO T 903 standard MA,

Pro Honda GN4 4-stroke oil or equivalent

270 lbs (120 kg) rider, all cargo and accessories

Quick Reference

06/04/27 10:54:42 31HM3740_237

Quick Reference

Tires

Tire Pressure (cold)

Spark Plugs

Fuse

Front:

Rear:

Front:

AT 22 × 7-10 ★★

OHTSU P/V 102

AT 22 × 10-9 ★

OHTSU P/V 702

4.4 psi (30 kPa , 0.30 kgf/cm )

Rear: 2.9 psi (20 kPa , 0.20 kgf/cm ) maximum tire pressure:

Front:

Rear:

4.8 psi (33 kPa , 0.33 kgf/cm )

3.3 psi (23 kPa , 0.23 kgf/cm ) minimum tire pressure:

Front:

Rear: standard:

4.0 psi (27 kPa , 0.27 kgf/cm )

2.5 psi (17 kPa , 0.17 kgf/cm )

DR8ES-L (NGK) or

X24ESR-U (DENSO) cold climate:

DR7ES (NGK) or

X22ESR-U (DENSO) high speed riding:

DR8ES (NGK) or

X27ESR-U (DENSO) main: 15A

Quick Reference

No results