TomTom GO car navigation systems User Guide

PDF

مستند

TomTom GO

What’s in the box

Chapter 1 What’s in the box

Your TomTom GO

C D E

FF G

On/off button

Microphone

Release button

Charging light

Light sensor

Reset button

Speaker

Memory card slot

SIM card slot

I b

Windscreen dock

Audio out connector

External microphone connector

External antenna connector

Power connector

TomTom connector c

Home dock

Home charger connector

USB connector d

Car charger

Product code card g

Home charger i

External microphone f

Carry case h

Documentation pack j

Memory card (SD card)

Chapter 2 Welcome

Your TomTom GO will help you to manage your work and keep in contact with your office.

For example, your office can send you orders, including information about what you have to do and where you need to go.

You can then do the following:

• Select and read orders from a list.

• Accept or reject an order.

• Start navigating immediately to an order.

• Report on the status of an order.

• Send text and status messages to your office.

• Register when you are working and when you take a break.

Attaching your Windscreen Dock

It is very important to attach the Windscreen Dock properly to your windscreen and also to put it in a good place. The installation poster shows how to attach the dock to your windscreen. Some tips for attaching the Windscreen Dock:

• Make sure your windscreen is clean and dry before trying to attach the dock.

• Place the dock so it does not block your view of the road in any way. But make sure the dock is placed so that it is close to your line of sight while you are looking at the road. In this way you can glance at the screen easily while driving.

• Place the dock so that you don’t have to reach to touch the screen. You should be able to tap the screen easily while driving.

• Attach the dock to an area of the windscreen where the glass is flat, not curved.

Chapter 3 Important information

Warning

When you switch off your TomTom GO, the GSM module does not switch off immediately.

After you switch your TomTom GO off, the GSM module stays on for the times below:

• 15 minutes - if you remove your TomTom GO from the Windscreen Dock.

• 2 hours - if you leave your TomTom GO docked.

A GSM module can interfere with electrical devices such as cardiac pacemakers, hearing aids and aviation equipment.

Interference with these devices may endanger the health or life of others.

Do not use near unprotected electrical units nor in areas where the use of mobile telephones is prohibited, such as hospitals and airplanes.

GPRS coverage

If you are in an area where there is no GPRS coverage, any messages sent by you or to you are stored. All stored messages will be sent once the GPRS connection is available again.

To check the GPRS coverage, tap the GPRS connection indicator in the Driving

View.

The SIM card

Please note that the removal of your SIM card from your TomTom GO may result in a loss of data, and we therefore recommend that you do not remove the SIM card from your GO. TomTom shall not be liable in any way for any loss of data resulting from the removal of the SIM card from your TomTom GO.

Odometer and position tracking

Your TomTom GO has an odometer for recording the distance you travel. It only works when your TomTom GO is docked. Your vehicle’s position is also only sent to TomTom WEBFLEET when your GO is docked.

Chapter 4 Before you start...

Backup your TomTom GO

It’s always a good idea to make a backup of the contents of your TomTom GO. You can make a backup using TomTom HOME.

Secure your TomTom GO

Set owner

Set a password for your TomTom GO so that only you can use it. Every time you start your GO you will have to enter your password.

To set your password, run your GO using TomTom HOME. From the Preferences menu, click Set owner to set a password.

To set the password, you have to run your GO using TomTom HOME. You can then use TomTom HOME to set the password. To set a password on your device, do the following:

1. Connect your GO to your computer and switch it on.

2. Start TomTom HOME if it does not start automatically.

If you do not have TomTom HOME installed, insert the CD that came with your

GO to install it.

Alternatively, you can download TomTom HOME from www.tomtom.com.

Make sure you always have the latest version of TomTom HOME. For more

information about TomTom HOME, see Using TomTom HOME on page 63.

3. In the Planning section, select your GO.

A picture of your GO is shown in the main section of TomTom HOME.

4. Click the On/Off button on the picture of your GO to switch it on in TomTom

HOME.

Your GO starts in TomTom HOME. You can now set the password on your GO using TomTom HOME. Don't unplug your GO, just use it as you normally would by clicking the buttons shown on your computer.

5. From the Main Menu in your device, click Change preferences.

6. Click Set owner. You may have to click the arrow until you reach the page where

Set owner is shown.

If you cannot find the button Set owner, make sure that all buttons are shown in your GO. Tap the button Show ALL menu options. All buttons will now be shown.

You can now set the password for your GO. You can also set your name and address, which will then be shown when your GO starts up.

Take care of your TomTom GO

It is important to take care of your GO and to clean it correctly.

• Use a soft cloth to wipe the screen of your GO; do not use any liquid cleaners.

• If your GO gets wet, dry it with a soft cloth.

• Do not open the casing of your GO under any circumstances. Doing so may be dangerous and will invalidate your warranty.

• Do not use the memory card (SD card) with any device other than a TomTom device. Other devices may damage the memory card.

• Do not expose your GO to high or low temperatures, which can cause permanent damage. For example, don’t leave it in the car on hot summer days or during cold winter nights.

Chapter 5 Getting started

Switching on

Follow the instructions on the Installation Poster to dock your TomTom GO in your car.

The first time you switch on your TomTom GO, it may take up to 20 seconds to start. To switch off your TomTom GO, press and hold the On/Off button for 2 seconds.

Setting up

You have to answer a few questions to set up your TomTom GO. Answer the questions by tapping the screen. You will use the touchscreen for everything you do with your GO.

You can change these settings at any time using the Preferences menu. For

information about the Preferences menu, see Preferences on page 53.

Once you have answered the questions, your GO will display the Driving View. The

Driving View is shown in black and white until your GO locates your current position.

For more information about the Driving View, see Driving View on page 11.

Locating your current position

Your TomTom GO must be outdoors to locate your current position. The first time you start your GO, it can take up to 5 minutes to find your current position. If it takes longer than 5 minutes, make sure that you are in an open place without tall buildings or trees around you.

In the future, your position will be found much faster, normally within a few seconds.

Once your GO has located your current position, the Driving View is shown in full colour and shows your position on the map.

Chapter 6 Docking your TomTom GO

Windscreen dock

Use the windscreen dock to position your TomTom GO in your car. The installation poster shows how to attach the dock to your windscreen.

Tips

• Make sure your windscreen is clean and dry before trying to attach the dock.

• Place the dock so it does not block your view of the road.

• Attach the dock to an area of the windscreen where the glass is flat, not curved.

Home dock

With the home dock you can charge your TomTom GO when it is not in the car and also connect your GO to your computer. Connect the home dock to the home charger and your computer as shown below.

Place your TomTom GO in the home dock in the same way as you place it in the windscreen dock.

When connected to your computer, you can use TomTom HOME with your GO. For

information about TomTom HOME, see Using TomTom HOME on page 63.

Driving View

Chapter 7 Driving View

Buttons to zoom in and zoom out on your position.

Button that shows when a new message or order is received. Tap the envelope to open the message or order.

Your current position.

The name of the next major road or road sign information, if applicable.

Button that shows whether you are on a business trip or private trip, or the status of an order. Tap the button to change the status. Some of the buttons are explained below.

The next instruction.

This area shows you what to do and when you will have to do it.

Tap this area to repeat the last spoken instruction and to change the volume.

The name of the next street to turn onto.

Information about your journey.

Indicator for the GPRS connection

Shows whether your TomTom GO has a GPRS connection. Tap the indicator for information about the GPRS coverage.

Indicator of the strength of the GPS signal.

For more information about GPS, see How does navigation work? on page 65.

The buttons below can all be shown on the left-hand side of the Driving View. Tap one of these buttons to bring up the details or to change the settings.

New order or message

... signifies that you have new unread orders or messages.

Status of order

... signifies the status of the current order when you are on a business trip or in working time. Each status has a different icon.

Private trip

... signifies that you are on a private trip. This icon only appears when ’Change logbook mode’ is activated.

Break

... signifies that you have a break. This icon only appears if

’Report work time’ on your TomTom GO is activated.

End of work

... signifies that you have finished work.

Locating disabled

... signifies that the locating of your vehicle is disabled when you are on private trips, you have a break or have finished work (only when activated by the office).

Chapter 8 Menus

Main menu

Tap the screen at any time when TomTom GO displays the Driving View to open the Main Menu.

• Navigate to...

Tap this button to start planning a route.

• Find alternative...

Tap this button if you want to avoid part of your route, travel via a specific location or calculate an alternative route.

• Show orders

Tap this button to read and work with messages and orders sent by your office.

• Report to office

Tap this button to send messages to your office.

• Change preferences

This button opens the Preferences menu. You can change many things about the way TomTom GO looks and behaves.

Orders and messages

Chapter 9 Orders and messages

The office can send service, delivery and pick-up orders. They will be stored on your TomTom GO, so that you can read and deal with them at any time. These three kinds of orders are marked differently. You can find them under Show

orders.

These symbols show the type and status of items in your list of orders and messages:

New text message

Text message that has been read

New service order

Service order in progress

Suspended service order

Finished service order

Cancelled or rejected service order

New delivery or pick up order (compare to the symbol for service orders)

Working on orders

When you receive a new message or order, an envelope is shown in the Driving view. Tap the envelope to open the message or order. If you have received more than one new message, the latest message will be displayed first.

You will also find all your orders and messages in a list under Show orders.

1. Tap the screen to bring up the Main Menu.

2. Tap Show orders.

3. Select an order from the list.

4. To start working on this order tap I agree. (This is configurable by the office.)

To reject the order tap Options, then tap Reject order. You can enter a reason for rejecting the order.

If you have agreed, you are asked to start this order. If the order contains destination data, you will be asked to start navigation.

As soon as you start the order, you can report your current activities. Tap the button that shows your activity to report. Tap Status to report to your office by using the status messages defined by the office. To do this, tap Status and proceed as explained under 'Report to office'.

Suspend and change orders

1. To quickly suspend the current order, select it from the list or tap the order button in the Driving View.

2. Tap Options.

3. Tap Suspend.

Switching to another order

1. If you want to switch to another order, select the new order from the list.

2. Then you will be asked to suspend the current order and start working on the new one.

You will always be able to continue working on the suspended order. To do so, select the suspended order from the list and tap Resume.

Cancelling orders

1. If you want to cancel an order, first select the order.

2. Tap Options.

3. Tap Cancel.

You will be asked to enter a reason for cancelling the order.

Chapter 10 Report to office

Send text message

To send a text message to your office, do the following.

1. Tap Report to office in the Main Menu.

2. Tap Send text message.

3. Enter your message.

4. Tap Done to send the message to the office.

Enter your message using the keyboard and the following buttons:

Tap this button to enter capital letters

Tap this button to enter lowercase letters

Tap this button to switch to the numeric/special characters keyboard

Tap this button to switch back to alphabetic keyboard

Tap this button to delete single characters

Send status message

Status messages must be defined by your office. You can select the appropriate message and send it as it is, or you can add information.

To send a status message, do the following:

1. Tap Report to office in the Main Menu.

2. Tap Send status message.

3. Select a status message from the list by tapping it.

If you want to add information, tap Edit. If not tap Send to send the message directly to the office.

4. Tap Send to send the message to your office with any information you have added.

Planning a route

Chapter 11 Planning a route

Planning a route with TomTom GO is very simple. If you need to navigate to a destination without an order, you can plan a route.

Note: You should always plan your journeys before you start driving. It is dangerous to plan routes when you are already moving.

1. Tap the screen to bring up the main menu.

2. Tap Navigate to...

For your first journey, we will navigate to an address.

3. Tap Address.

When you enter an address, you can choose from four options:

• City centre - tap this button to set your destination as the centre of a city or town.

• Street and house number - tap this button to set an exact address as your destination.

• Postcode - tap this button to enter a postcode as your destination.

Note: You can enter a postcode for any country. In the UK and the

Netherlands, postcodes are detailed enough to identify a house on their own. In other countries you can enter a postcode to identify a town or area.

You will then have to enter a street and house number.

• Crossing or intersection - tap this button to set your destination as the point where two streets meet.

For your first journey, we will enter an exact address.

4. Tap Street and house number.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are shown. When your destination is shown in the list, tap the name of the town to set the destination.

6. Start to type the name of the street.

As with the name of the town, the names of the streets that match what you have typed are shown. When your destination is shown in the list, tap the name of the street to set the destination.

7. Now enter the house number of your destination and then tap Done.

8. GO asks you whether you need to arrive at a particular time.

Tap YES to enter an arrival time. GO shows you whether you will arrive on time.

For more information, see Arrival times on page 21.

The route is then calculated by your TomTom GO.

9. When the route has been calculated, tap Done.

TomTom GO will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen.

Note: Before you can plan a route in this way, TomTom GO must first locate your current position.

Arrival times

When you plan a route, your GO asks you if you need to arrive by a particular time:

Tap YES to enter an arrival time.

Your GO calculates your arrrival time and shows you whether you will arrive on time.

You can also use this information to work out when you need to leave. If your GO shows you that you will arrive 30 minutes early, you can wait and leave in 30 minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your journey. The status bar shows whether you will arrive on time or late, as shown below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered, it is shown in red.

Planning in advance

You can also use your GO to plan journeys in advance by selecting both your starting point and your destination. You could, for example, do the following:

• Find out how long a journey is going to take before you start.

• Check the route of a journey you are planning.

• Check a route for someone who is coming to you and explain the route to them.

To plan a route in advance, follow these steps:

1. Tap the screen to bring up the main menu.

2. Tap Advanced planning.

3. Select the starting point for your journey in the same way as you would normally select your destination.

4. Set the destination for your journey.

5. Choose the type of route that should be planned.

• Fastest route - the route which takes the least time.

• Shortest route - the shortest distance between the locations you set. This may not be the quickest route, especially if the shortest route is through a town or city.

• Avoid motorways - a route which avoids motorways.

• Walking route - a route designed for making the journey on foot.

• Bicycle route - a route designed for making the journey on a bicycle.

• Limited speed - a route for a vehicle which can only drive at a limited speed.

You have to specify the maximum speed.

6. Your TomTom GO plans the route between the two locations you selected.

More information about a route

To find out about your route in detail, tap the Details button on the route summary screen.

You can then select from the following options:

Tap this button for a list of all the turn instructions on the route.

This is particularly useful if you need to explain a route to someone else.

Browse as text

Browse as images

Tap this button to see each turn in the journey. Tap the right and left arrows to move forwards and backwards through the journey.

Tap the screen to turn off the 3D display and view the map from above.

Browse map of route

Tap this button to see an overview of the route using the map browser.

For more information about the map browser, see Using the map on page 31.

Tap this button to watch a demo of the journey. You can interrupt the demo at any time by tapping the screen.

Show route demo

Tap this button to open the route summary screen.

Show route summary

Report work time

Driver ID

Chapter 12 Report work time

Using your TomTom GO you can report your general working status. You can report the time you start and finish work, and time you spend having a break.

First you have to enter your Driver ID.

Note: Your office can configure via TomTom WEBFLEET, that you have to enter your Driver ID each time you switch on your TomTom GO.

1. Tap the screen to bring up the Main Menu.

2. Tap Change preferences.

3. Tap Change Driver ID.

4. Enter your Driver ID, then tap Done.

Your Driver ID will be saved and used for all reports until you change it.

Report work time

To report work times to TomTom WEBFLEET, do the following:

1. Tap the screen to bring up the Main Menu.

2. Tap Report work time.

3. Tap the appropriate button to change your work status.

When you tap Finish work, this will be indicated in the Driving View.

If you are working on an order, the current order status is shown in the Driving

View.

Note: In the Main Menu either the button Report work time or Change

logbook mode is available. These functions are activated using TomTom

WEBFLEET by your office.

Change logbook mode

Chapter 13 Change logbook mode

You can generate a driver’s logbook with your TomTom GO.

Important

• Do not use your TomTom GO in different vehicles.

• Sychronize the odometer value on every start.

• Your TomTom GO does not record trips when it is switched off. This will be designated as private use.

To change the kind of trip do the following:

1. Tap the screen to bring up the Main Menu.

2. Tap Change logbook mode.

Note: Either the button Report work time or Change logbook mode is available. Both cannot be available at the same time.

3. Select the appropriate mode.

The current logbook mode is shown in the bottom half of the screen, as well as journey specific information.

If the logbook mode is set to Private trip or Commute to work, this is shown in the

Driving View. During a business trip, the current order status is shown.

When you use the logbook, each time you switch on your TomTom GO the odometer is shown. You can then synchronize the odometer in your TomTom GO with your vehicle’s odometer.

You can also adjust the odometer using the logbook:

1. Tap the screen to bring up the Main Menu.

2. Tap Change logbook mode.

3. Tap Adjust.

4. Tap the buttons to adjust the odometer to match your vehicle’s odometer.

Important

The odometer on your TomTom GO only measures the distance you travel when it is docked in the Windscreen Dock.

Call contact

Chapter 14 Call contact

Orders can contain a contact name and a telephone number. You can call this number from your TomTom GO.

Note: To call contacts you need a mobile phone with Bluetooth® that is compatible with your TomTom GO.

1. Tap the screen to bring up the Main Menu.

2. Tap Show orders.

3. Select an order from the list.

4. Tap Options.

5. Tap Call.

6. Tap the contact name to call the contact using your TomTom GO.

Chapter 15 Finding alternative routes

Find alternative...

Once you have planned a route, you may want to change something about the route, without changing your destination.

Why change the route?

Maybe for one of these reasons:

• You can see a roadblock or a line of traffic ahead.

• You want to travel via a particular location, to pick someone up, stop for lunch or fill up with petrol.

• You want to avoid a difficult junction or a road you don’t like.

Tap Find alternative... in the Main Menu to change the route that is currently planned.

Then tap one of the options below.

Calculate alternative

Avoid roadblock

Tap this button to calculate an alternative to the route already planned.

Your GO will look for another route from your current location to your destination.

If you decide you would prefer to use the original route after all, tap

Recalculate original.

Why would I need to do this?

Apart from the roads near your position and near your destination, the new route will use totally different roads to reach your destination. This is an easy way of calculating a totally different route.

Tap this button if you can see a roadblock or a line of traffic ahead. You then have to choose how much of the route ahead you want to avoid.

Choose from the different options: 100m, 500m, 2000m, 5000m. Your GO will recalculate your route avoiding the section of the route for the distance you selected.

Don’t forget that once a new route is calculated, you may have to turn off the road you are on very soon.

If the roadblock suddenly clears, tap Recalculate original to return to your original route.

Travel via...

Tap this button to change your route so that it passes a particular location, perhaps to pick someone up on the way.

You choose the location you want to pass in the same way as you choose a destination. So you can select from all the same options: for example,

Address, Favourite, Point of Interest and Point on map.

Your GO will calculate a new route to your destination that passes the location you chose.

Using this button, you can only travel via one location. If you want to pass

more than one, use an Itinerary. For more information, see Itinerary

planning on page 41.

Tap this button to return to the original route without any deviations for roadblocks or to travel via particular locations.

Recalculate original

Avoid part of route

Minimise traffic delays

Tap this button to avoid a part of the route. Use this button if you see that your route includes a road or junction you don’t like, or which is well-known for traffic problems.

You then choose the road you want to avoid from a list of the roads on your route.

Tap this button to recalculate your route so that it avoids traffic problems as much as possible. Your GO will check if there are any traffic problems on your route and work out the best route to avoid the problems.

For more information about using TomTom Traffic, see TomTom Traffic on page 48.

Using the map

Chapter 16 Using the map

Every time you use your TomTom GO to plan a route, you are using the map.

However, you can use the map in many other ways.

To open the map, tap Browse map in the Main Menu.

Place your finger on the screen and drag it across the screen to move the map.

The scale bar

Move the handle on the scale bar to zoom in and out on the cursor position.

Your current position

GPS button.

Tap this button to centre the map on your current position.

The Options button

Use the Options button to set what is shown on the map.

The cursor

The Find button

Tap this button to find specific addresses and Points of Interest on the map.

The Cursor button

Tap this button to navigate to the cursor position, make a Favourite of the cursor position, or find a Point of Interest near the cursor position. See below for more information.

The zoom bar.

Change the scale of the map by moving the zoom bar up or down.

Using the Cursor button

You can use the map to find addresses and Points of Interest (POIs), for example, restaurants, train stations and petrol stations.

With the Cursor button, you can use what you have found. Tap the cursor button to open the page of buttons shown below:

Navigate there

Tap this button to find a POI near the cursor position. For example, if you have found a restaurant to go to, you can search for a parking garage nearby.

Find POI nearby

Call

Tap this button to call the cursor position. This button is only available if your GO has the phone number for the cursor postion.

The phone numbers of many POIs are stored in your GO. If you entered phone numbers for POIs you have created, you can also call them.

For more information about hands-free calling, see Hands-free calling on page 50.

Tap this button to create a Favourite at the cursor position.

For more information about Favourites, see Favourites on page 33.

Add as

Favourite

Add as POI

Tap this button to create a POI at the cursor position.

For more information about POIs, see Points of Interest on page 36.

Tap this button to travel via the cursor position. This button is only available if you are currently navigating to a destination.

Travel via...

Tap this button to navigate to the cursor position. Your GO will calculate the route there.

Chapter 17 Favourites

What are Favourites?

Favourites are places that you go often. You can create Favourites so that you don’t have to enter the address every time you want to navigate there.

They don’t have to be places you like, just useful addresses.

How can I create a Favourite?

From the Main Menu, tap Add Favourite.

Note: The button Add Favourite may not be shown on the first page of the

Main Menu. Tap the arrow to open other pages in the Main Menu.

You can then select the location of the Favourite from the list below.

Give your Favourite a name that is easy to remember. Your GO will always suggest a name, usually the address of the Favourite. To enter the name, just start typing.

You don’t have to delete the suggested name.

You can set your Home location as a Favourite.

Home

Favourite

Address

You cannot create a Favourite from another Favourite. This option will always be unavailable in this menu.

To rename a Favourite, tap Manage Favourites in the Preferences menu.

For more information, see Manage Favourites on page 55.

You can specify an address to be a Favourite. When you enter an address, you can choose from four options. The same options as appear in the

Navigate to... menu:

• City centre

• Street and house number

• Postcode (fully supported only in UK and the Netherlands)

• Crossing or intersection

Select a Favourite location from a list of places you have recently used as destinations.

Recent destination

Point of

Interest

You can add a Point of Interest (POI) as a Favourite.

Does it make sense to do this?

If you visit a POI you particularly like, for example a restaurant, you can add it as a Favourite.

To add a POI as a Favourite, tap this button, then do the following:

1. Narrow your choice of POIs by selecting the area where the POI is.

GPS postion

Point on map

You can select one of these options:

• POI near you - to search from a list of POIs near your current position.

• POI in city - to choose a POI in a particular town or city. You have to specify a town or city.

• POI near Home - to search from a list of POIs near your Home location.

If you are currently navigating to a destination, you can also select from a list of POIs which are on your route or near your destination. Choose one of these options:

• POI along route

• POI near destination

2. Select the category of POI.

Tap the category of POI if it is shown or tap the arrow to choose from the complete list.

Tap Any POI category to search for a POI by name.

For more information about POIs, see Points of Interest on page 36.

Tap this button to add your current postion as a Favourite.

For example, if you see stop somewhere you like, while you are there you can tap this button to create the Favourite.

Tap this button to create a Favourite using the map browser.

Select the location of the Favourite using the cursor, then tap Done.

For more information about the map browser, see Using the map on page 31.

Tap this button to create a Favourite by entering latitude and longitude values.

Latitude

Longitude

Last docked

Tap this button to save the location where your TomTom GO was last docked in the windscreen dock in your car.

If your GO loses GPS reception for the last part of the journey, for example, if you park in an underground car park, the last-known position will be used. In this case, it would probably be the entrance to the car park.

How can I use a Favourite?

You will normally use a Favourite as a way of navigating to a place without having to enter the address. To navigate to a Favourite, do the following:

1. Tap the screen to bring up the Main Menu.

2. Tap Navigate to...

3. Tap Favourite.

4. Select a Favourite from the list.

Your GO calculates the route for you.

5. When the route is calculated, tap Done.

Your GO will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen.

How many Favourites can I create?

You can create up to 48 Favourites. If you want to add more than 48, we suggest that you make some POI categories and add some of your Favourites as POIs.

For more information about POIs, see Points of Interest on page 36.

How can I delete a Favourite?

1. Tap the screen to bring up the Main Menu.

2. Tap Change preferences to open the Preferences menu.

3. Tap Manage Favourites.

Tip: Tap the arrow to move to the next page buttons.

4. Tap the Favourite you want to delete.

5. Tap Delete.

How can I change the name of a Favourite?

1. Tap the screen to bring up the Main Menu.

2. Tap Change preferences to open the Preferences menu.

3. Tap Manage Favourites.

Tip: Tap the arrow to move to the next page buttons.

4. Tap the Favourite you want to rename.

5. Tap Rename.

Points of Interest

Chapter 18 Points of Interest

Points of Interest or POIs are useful places on the map. Here are some examples:

• Restaurants

• Hotels

• Museums

• Parking garages

• Petrol stations

Tip

To help you stick to the speed limit, your TomTom GO also includes a list of

Safety Cameras.

To find out how to activate Safety Cameras, see the TomTom PLUS services leaflet included with your GO. Safety Cameras are not available in all countries.

Showing POIs on the map

Enable/ disable POIs

1. Tap Enable/disable POIs in the Preferences menu.

2. Select the POI categories to display on the map.

Tap Find to search for a POI by name.

3. Tap Done.

The POIs you selected are shown on the map as symbols.

Calling a POI

Your TomTom GO knows the phone numbers for many POIs. You can, for example, call a restaurant to book a table or a cinema to book tickets.

For information about using your TomTom GO for hands-free calling, see Hands-

free calling on page 50.

Navigating to a POI

1. Tap the screen to bring up the Main Menu.

2. Tap Navigate to... in the Main Menu.

3. Tap Point of Interest.

4. Narrow your choice of POIs by selecting the area where the POI is.

You can select one of these options:

• POI near you - to search from a list of POIs near your current position.

• POI in city - to choose a POI in a particular town or city. You have to specify a town or city.

• POI near Home - to search from a list of POIs near your Home location.

If you are currently navigating to a destination, you can also select from a list of

POIs which are on your route or near your destination. Choose one of these options:

• POI along route

• POI near destination

5. Select the category of POI:

Tap Any POI category to search for a POI by name.

Tap the category of POI if it is shown.

Tap the arrow to choose from the complete list of categories. Select the category from the list or start to type the name of the category and select it when it is shown in the list.

6. From the list of POIs shown, select the POI you want to navigate to. The table below explains the distances listed next to each POI.

POI near you

POI in city

POI near Home

POI along route

POI near destination

Distance from your current location

Distance from the city centre

Distance from your Home location

Distance from your current location

Distance from your destination

If you know the name of the POI, tap Find and type the name. Select it from the list when it is shown.

Once you have selected a POI, the route to the POI is calculated by your

TomTom GO.

Managing POIs

Tap Manage POIs from the Preferences menu.

Manage POIs

Note: The Manage POIs button is only available when all menu buttons are shown. To show all menu buttons, tap Show ALL menu options in the

Preferences menu.

You can, for example, do the following:

• Create your own POI categories and add POIs to them.

• Set warnings when you get close to POIs.

Why would I want to create my own POIs?

A POI acts like a shortcut - once you have saved a location as a POI you never have to type the address of that POI again. But when you create a POI you can save more than just the location.

• Phone number - when you create a POI, you can save a phone number with it.

• Categories - when you create a POI you have to put it in a category.

For example, you could create a category of POIs called ‘Favourite restaurants’.

With each POI, save their phone number so that you can call them from your GO to reserve a table.

How can I create my own POIs?

1. Tap the screen to bring up the Main Menu.

2. Tap Change preferences.

3. Tap Manage POIs.

4. Before you can add a POI, you have to create at least one POI category. Every

POI is assigned to a POI category. You can only add POIs to POI categories you have created yourself.

Tap Add POI category.

5. Enter a name for your POI category, for example, ‘Friends’ or ‘Favourite restaurants’. Then select a marker for your POI category.

6. Tap Add POI.

Add POI category

7. Select the POI category you want to add the POI to.

8. Select the location of your POI from the list below.

Add POI

Home

You can set your Home location as a POI.

If you want to change your Home location, you can create a POI of the Home location before you change it.

Favourite

Address

You can create a POI from a Favourite.

You can only create a limited number of Favourites. If you want to create more Favourites you have to delete some Favourites first. Before you delete a Favourite, make it into a POI so that you don’t lose the address.

You can specify an address to be a POI. When you enter an address, you can choose from four options. The same options as appear in the Navigate to... menu:

• City centre

• Street and house number

• Postcode (fully supported only in UK and the Netherlands)

• Crossing or intersection

Select a POI location from a list of places you have recently used as destinations.

Recent destination

You can add a Point of Interest (POI) as a POI. For example, if you are creating a category of POIs for your favourite restaurants, use this option instead of entering the addresses of the restaurants.

Point of

Interest

GPS postion

Point on map

Tap this button to add your current postion as a POI.

For example, if you stop somewhere you like, while you are there you can tap this button to create the POI.

Tap this button to create a POI using the map browser.

Select the location of the POI using the cursor, then tap Done.

For more information about the map browser, see Using the map on page 31.

Tap this button to create a POI by entering latitude and longitude values.

Latitude

Longitude

Last docked

Tap this button to save the location where your TomTom GO was last docked in the windscreen dock in your car.

How can I set warnings for POIs?

1. Tap the screen to bring up the main menu.

2. Tap Change preferences.

Warn when near POI

3. Tap Manage POIs.

Note: The Manage POIs button is only available when all menu buttons are shown. To show all menu buttons, tap Show ALL menu options in the

Preferences menu.

4. Tap Warn when near POI.

5. Select the category of POI you want to be warned about.

Select the category from the list or start to type the name of the category and select it when it is shown in the list.

6. Set how close the POI should be when you receive a warning.

7. Choose the warning sound for the category of POI you selected.

Chapter 19 Itinerary planning

What is an Itinerary?

An Itinerary is a plan for a journey with more stops than just your final destination.

An Itinerary is made up of the following items:

• Destinations - the end of a particular journey, the place where you want to stop.

• Waypoints - points on your journey that you want to pass.

Here’s an example of an Itinerary:

Destinations are shown with this symbol.

Waypoints are shown with this symbol.

When would I use an Itinerary?

You could use an Itinerary for these kinds of trips:

• A driving holiday through a country with lots of stops.

• A two day car journey with an overnight stop.

• A short drive which passes particular Points of Interest.

In all these examples you could tap Navigate to... for each place. However, if you use an Itinerary, you can save time by programming everything in advance.

Creating an Itinerary

Itinerary planning

1. Tap the screen to bring up the Main Menu.

2. Tap Itinerary planning.

The Itinerary planning screen opens. At first, there are no items on the Itinerary.

3. Tap Add and select a location.

Tip

You can add items to your Itinerary in any order and organise them into the

Itinerary later.

Following an Itinerary

When you use an Itinerary to navigate, the route will be calculated to the first destination on the Itinerary. Your TomTom GO calculates the remaining distance and time to the first destination and not for the whole Itinerary.

As soon as you start to use an Itinerary, the route is calculated from your current position. You do not need to set a departure point.

When you have passed a waypoint or reached a destination, it is marked as visited.

Waypoints are shown on the map but your GO will not warn you when you are approaching a waypoint, or tell you when you reach the waypoint.

Organising an Itinerary

Tap an item on your Itinerary to open a page of buttons for editing the item. The buttons shown below are available.

Mark as waypoint

Mark as destination

Mark ‘visited’

Mark ‘to visit’

You can change a waypoint into a destination using this button.

Remember that waypoints are points on your journey to your destination that you want to pass and destinations are places where you want to stop.

This button is only shown if the item you tapped is a destination.

You can change a waypoint into a destination using this button.

Remember that destinations are places where you want to stop, and waypoints are points on your journey to your destination that you want to pass.

This button is only shown if the item you tapped is a waypoint.

Tap this button to miss out part of your Itinerary. Your GO will ignore this item and all the items before it in the Itinerary.

It will navigate you to the next item in the Itinerary.

This button is only shown if you are still due to visit this item.

Tap this button to repeat part of your Itinerary. Your GO will navigate you to this item followed by the rest of the items in the Itinerary.

This button is only shown if you have already visited this item.

Tap this button to move the item up the Itinerary.

This button is unavailable if the item is at the top of the Itinerary.

Move item up

Tap this button to move the item down the Itinerary.

This button is unavailable if the item is at the bottom of the Itinerary.

Move item down

Show on map

Tap this button to see the location of the item on the map.

For more information about the map browser, see Using the map on page 31.

Tap this button to delete the item from the Itinerary.

Delete item

Start using an Itinerary

Tap Options, then tap Start navigation.

Once you have created an Itinerary, it’s a good idea to save it. To save an Itinerary, tap Save Itinerary.

To load a saved Itinerary, tap Load Itinerary.

To create a new Itinerary, tap New Itinerary and to delete one, tap Delete Itinerary.

Chapter 20 Sound

Your TomTom GO produces sound for many different things:

• Spoken instructions

• Hands-free calls

• Warnings about Points of Interest nearby

• Music

Note: You can play music through your TomTom GO by connecting your iPod to the Windscreen Dock using the iPod Connect Cable (available as an accessory).

This chapter talks about the following:

• Sound basics - changing the volume.

• Speakers - using the internal speaker of your GO and using external speakers.

• Using more than one speaker - you can use different speakers for different types of sound.

• Voices - using human voices and computer voices. What are the differences between them and what can they do?

For information about making hands-free calls on your GO, see Hands-free

calling on page 50.

Changing the volume yourself

You can change the volume in two ways:

• Tap the bottom left hand area of the Driving View. The last spoken instruction is repeated and the volume slider is shown.

Move the volume slider to adjust the volume.

Note: If you change the volume in this way during a hands-free phone call, you will change the volume only for all hands-free calls. The volume for other sound will not change.

• In the Main Menu, tap Change preferences, then tap Volume preferences.

Move the volume slider to adjust the volume. Tap Test to check the changes you make.

Changing the volume automatically

Your GO can change the volume automatically depending on how noisy it is in the car.

Volume preferences

1. In the Main Menu, tap Change preferences.

2. Tap Volume preferences.

3. Select Link volume to noise level.

Your GO will now change the volume depending on the background noise.

Internal and external speakers

Your TomTom GO includes a high quality speaker. This internal speaker will be used to play all the sound your GO makes, unless you set your GO to use an external speaker.

You can connect your GO to external speakers in two ways:

• Using the audio cable

For example, if your car stereo has a line in connector, you can play sound from your GO through your car speakers using the audio cable.

• By connecting to Bluetooth® Hi-Fi speakers

This could also be a Bluetooth® Hi-Fi headset.

Note: Hands-free calls are always played using the internal speaker.

Using the audio cable

The audio cable is available as an accessory for your TomTom GO.

To play sound through your car stereo or other external speaker using the audio cable, do the following:

1. Plug the audio cable into the line out connector on the windscreen dock, as shown below.

Speaker preferences

2. Plug the audio cable into the line in connector on your car stereo or other external speaker.

Note: Not all car stereos have a line in connector. Check the manual for your car stereo for information.

3. If you are using your car stereo, select Line in on your car stereo as the input source.

4. On your GO, tap Speaker preferences in the Preferences menu.

5. Select the sound that you want played through the external speakers. There are two options:

• Play music over external speaker

• Play spoken instructions over external speaker

Note: Hands-free calls are always played over the internal speaker.

You can select either or both options.

6. Tap Done.

7. Your GO asks you whether you want to use an external Bluetooth® Hi-Fi speaker. Tap NO.

Your GO will confirm that when connected, the sound you have selected will be played through the audio cable.

Note: If you connect the audio cable to the windscreen dock but do not connect it to an external speaker, your GO will still try to use the external speaker and you will not hear any sound.

You cannot listen to your car stereo and use the audio cable to play sound from your GO on the car stereo at the same time.

Using Bluetooth® Hi-Fi speakers

Speaker preferences

Your GO can play sound through Bluetooth® Hi-Fi speakers, such as a Bluetooth®

Hi-Fi headset, or a car stereo which uses Bluetooth®.

To play sound over Bluetooth® Hi-Fi speakers, do the following:

1. Tap Speaker Preferences in the Preferences menu.

2. Select the sound that you want played through external Bluetooth® Hi-Fi speakers. There are two options:

• Play music over external speaker

• Play spoken instructions over external speaker

You can select either or both options.

3. Tap Done.

4. Your GO asks you to confirm that you want to use an external Bluetooth® Hi-Fi speaker. Tap YES.

Your GO will start searching for Bluetooth® Hi-Fi devices.

5. Select your Bluetooth® Hi-Fi device from the list of devices found by your GO.

Your GO will try to establish a Bluetooth® connection with your device.

Your device may require you to enter a password on your GO before a

Bluetooth® connection can be established. See the documentation for your

Bluetooth® Hi-Fi device for more information.

Once connected, sound will be played through the external Bluetooth® Hi-Fi device. If your GO cannot establish a Bluetooth® connection then all sound will be played through the internal speaker or through the audio cable if it is connected to the windscreen dock.

Using more than one speaker

You can use different speakers for different types of sound.

When you select to use an external speaker, you select the sound that you want played through the external speaker. There are two options:

• Play music over external speaker

• Play spoken instructions over external speaker

Note: Hands-free calls are always played over the internal speaker.

Is it difficult to hear spoken instructions when music is playing?

When you choose to a Bluetooth® Hi-Fi device for music and spoken instructions, you are asked if you want pause music for spoken instructions. Otherwise, music is always paused for spoken instructions.

When you receive a hands-free call, music is always paused and spoken instructions are not given.

For information about making hands-free calls on your GO, see Hands-free

calling on page 50.

Selecting a voice

The first time you start your GO, you are asked to select a voice. To change the voice, tap Change voice in the Preferences menu. Then select the voice you would like.

Change voice

Chapter 21 TomTom Traffic

TomTom Traffic is a TomTom PLUS service that sends up-to-date traffic information to your GO.

TomTom Traffic takes the most up-to-date information from the best local sources.

Note: TomTom Traffic is not available in all countries or areas. Visit

www.tomtom.com/plus to check availability in your country.

Setting up TomTom Traffic

1. Tap TomTom Traffic in the Main Menu.

2. Tap Enable Traffic.

Using Traffic

When TomTom Traffic is enabled, or a TMC antenna is connected to the windscreen mount, the Traffic bar is shown on the right-hand side of the Driving

View, as shown below:

TomTom Traffic will immediately try to retrieve the latest traffic information.

Updating traffic information

With TomTom Traffic, there are two ways to update the traffic information:

• Tap Update traffic info in the Traffic menu.

• Set Traffic to be updated automatically at regular intervals.

To do this, tap Change Traffic preferences in the Traffic menu. Select

Automatically update traffic info while on route, then tap Done.

You are then asked if you want to limit how often Traffic is updated.

If you choose not to limit how often Traffic is updated, then TomTom will send updated traffic information to your GO as soon as it is available.

If you choose to limit how often Traffic is updated, you are asked to set a time.

TomTom saves this time limit and sends new traffic information at the interval you set. If there is no new traffic information, then TomTom will not send any information to your GO. This saves you money by not using your wireless data connection when there is no new information.

Using traffic information

Having up-to-date traffic information can help you to reduce your journey time.

Whenever you plan a route, the latest traffic updated you received from TomTom is taken into account by your GO when it plans the route.

Your GO can also recalculate your route if the traffic situation changes after you start a journey:

1. Tap Change Traffic preferences in the Traffic menu.

2. Select Automatically optimise route after every update.

After your GO gets new traffic information, it will automatically optimise your route.

Note: The best route may be the same as the route originally planned.

Chapter 22 Hands-free calling

If you have a mobile phone with Bluetooth®, you can use your TomTom GO to make phone calls and send and receive messages while you are driving.

Note: Not all phones are supported or compatible with all features. For more information, visit www.tomtom.com/phones

Connecting to your phone

First you must establish a connection between your mobile phone and your

TomTom GO. You only have to do this once. Your TomTom GO remembers your phone.

Tap Mobile phone in the Main Menu, then follow the instructions on the screen.

Setting up TomTom PLUS

After you have established a connection with your phone, you can set up a wireless data connection for TomTom PLUS services.

Tips

• Make sure that you switch on Bluetooth® on your phone.

• Make sure that your phone is set to ‘discoverable’ or ‘visible to all’.

• You may have to enter the password ‘0000’ on your phone in order to connect to your TomTom GO.

• Make your TomTom GO a trusted device on your phone. Otherwise you have to enter ‘0000’ every time.

See your phone’s user guide for information about Bluetooth® settings.

Your phonebook

You can copy your phonebook from your mobile phone to your TomTom GO so that you can make calls with just a few taps on the screen.

This is the safest way to make hands-free calls.

Note: You can copy your phonebook to your TomTom GO at any time. From the Mobile phone menu, tap Get numbers from phone.

Not all phones can transfer their phonebook to your GO. For more information, visit www.tomtom.com/phones

Making a call

Once you have established a connection with your phone, you can start making calls.

1. Tap Mobile phone in the Main Menu.

2. Tap Call.

Note: Make sure that your phone is currently selected. The current phone is shown at the bottom of the screen.

3. Do one of the following:

• Tap Home to call your Home location. If you have not entered a number for your Home location this button is unavailable. To enter a number, tap Change

Home number in the Phone preferences menu.

• Tap Number to enter a number to call.

• Tap Point of Interest to choose a Point of Interest (POI) to call. If your GO knows the phone number of a POI, this is shown next to the POI:

• Tap Phonebook entry to select a contact from your phonebook.

Note: If you have not copied your phonebook to your TomTom GO, the button Phonebook entry is unavailable.

• Tap Recently dialed to select from a list of people or numbers you have called recently using your GO.

• Tap Recent caller to select from a list of people or numbers who called you recently. Only calls you have received on your GO are saved in this list.

For information about POIs, see Points of Interest on page 36.

Receiving a call

If someone calls you while you are driving, accept or reject the call by tapping the screen.

Note: Hands-free calls are always played using the internal speaker.

Auto-answer

You can tell your TomTom GO to answer every call automatically after a certain time. Tap Phone preferences in the mobile phone menu, then tap Auto-answer

preferences.

Select when your TomTom GO will automatically answer your calls.

Sharing your TomTom GO

You can establish connections with up to 5 mobile phones. To add more phones, do the following

1. Tap Mobile phone in the Main Menu.

2. Tap Connect to your phone.

3. Tap Find other phone... and follow the instructions on the screen.

To switch between phones, tap Connect to your phone and then select your phone from the list.

Chapter 23 Preferences

You can change many things about the way your TomTom GO looks and behaves.

Tap Change preferences in the Main Menu.

Use night colours / Use day colours

Use Night colours

Use day colours

Tap this button to reduce the brightness the of the screen and use darker colours on the map.

To manually control the brightness of the screen, select not to link the night view to the dimmer settings in the Docking preferences in the Preferences menu.

When should I use this?

When it’s dark outside, it’s easier to see the screen of your GO if it isn’t so bright.

To change back to a brighter screen and brighter colours on the map, tap the button Use day colours.

Can my GO make this change automatically?

Yes it can. Your GO has a light sensor so it knows when it’s getting dark. To change to night and day colours automatically, tap Brightness preferences in the

Preferences menu. Then select Switch to night view when dark.

Turn off 3D display / Turn on 3D display

Tap this button to view the map from above while you are navigating.

Turn off 3D display

Turn on 3D display

To switch back to seeing the map from your perspective as you drive, tap Turn on

3D display.

When should I use this?

In some situations, it is easier to see the map from above. Perhaps if the roads are very complicated or if you are walking and using your GO to navigate.

Safety preferences

Safety preferences

Tap this button to set the following safety preferences:

• Safety lock

• Turn off map display

Safety lock

When you enable the safety lock, you are not able to access all buttons and features of your GO while driving.

The Main Menu shows only a few buttons that may be needed while you are driving.

As soon as your car stops moving, you will be able to access all of the buttons and features again.

Turn off map display

When you turn off the map display, instead of seeing your position on a map in the

Driving View, you will only see information about the next instruction.

When you tap this button, you have to specify when the map should be turned off.

These are the options:

• Always - you will only see information about the next instruction and arrows.

The map will never be shown.

• Above a certain speed - you set the speed at which the map is switched off.

When you are driving fast, the map can be distracting.

• Never - the map is never switched off.

Enable/disable POIs

Tap this button to set which categories of Points of Interest (POIs) should be shown on the map.

Select the POIs that you want to see on the map from the list:

Enable/ disable POIs

When you select a POI, it will be shown on the map by the symbol you can see next to each category in the list above.

To find a category of POI quickly, tap Find, then start to type the name of the POI category. As soon as the category is shown in the list, you can select it.

For more information about POIs, see Points of Interest on page 36.

Turn off sound / Turn on sound

Turn off sound

Tap this button to turn the spoken instructions off. The button changes to Turn on

sound. If you turn the sound off, warnings for upcoming POIs are also turned off.

Can I still use my GO to make hands-free calls when the sound is turned off?

Turning the sound off does not affect hands-free calling. You will still be able to hear the caller.

Tip

To change the volume, tap Volume preferences in the Preferences menu. For

more information, see Volume preferences on page 55.

To change the volume quickly while you are driving, tap the bottom left-hand section of the Driving View and move the slider.

To change the voice, tap Change voice in the Preferences menu. For more

information, see Sound on page 44.

Volume preferences

Volume preferences

Tap this button to change the volume of the spoken instructions.

Can my GO change the volume depending on how noisy it is in the car?

Select Link volume to noise level and your GO will change the volume according to the background noise. If there is a lot of noise in the car, the voice will get louder automatically. The noise level is constantly monitored by the microphone on your

GO.

For example, if you are driving on the motorway, which is often very noisy, the volume of the spoken instructions will be higher. When you are driving more slowly again, the volume will be lower.

Manage Favourites

Manage

Favourites

Tap this button to rename or delete Favourites.

To find a Favourite quickly, tap Find, then start to type the name of the Favourite.

As soon as the Favourite is shown in the list, you can select it.

For more information about Favourites, see Favourites on page 33.

Change Home location

Change

Home location

Tap this button to set or change your Home location.

Do I have to have my actual home as the Home location?

Your Home location can be a place you go often, for example, your office. It doesn’t have to be your actual home.

Why should I set a Home location?

Once you have set your Home location, you can navigate there quickly whenever you need to get there. In the Navigate to... menu, just tap Home.

Change voice

Tap this button to change the voice which gives you instructions.

Change voice

Change language

Change language

Tap this button to change the language used for all the buttons and messages you see on your GO.

You can choose from a wide range of languages. When you change the language, you are also given the opportunity to change the voice.

Warn when near POI

Warn when near POI

Tap this button to be alerted when you are near a Point of Interest (POI).

For example, your GO can tell you when there is a petrol station nearby.

To find out about POIs and about setting warnings for POIs, see Points of Interest on page 36.

Set clock

Set clock

Tap this button to set the time and to change the way the time is displayed.

The easiest way to set the time is by tapping the Sync button. Your GO will then take the time from the GPS information it receives.

For more information about GPS, see How does navigation work? on page 65.

Note: After using Sync to set the time, you may have to adjust the hours depending on your time zone. Your GO works out your time zone and always keeps the time correct using the GPS information.

You can only use Sync if you have GPS reception, so you cannot set the clock in this way when you are indoors.

Switch map

Switch map

Tap this button to change the map you are using.

When do I need to switch map?

You have to tell your GO which map you want to use. If there is more than one map on the memory card in your GO, you can switch to another map.

Note: When you switch to another map, you may need to activate that map.

Keyboard preferences

Keyboard preferences

Tap this button to select the size of the keys on the keyboard and the keyboard layout. You can select from two sizes:

• Large keyboard

• Small keyboard

Three keyboard layouts are available:

• ABCD keyboard

• QWERTY keyboard

• AZERTY keyboard

You use the keyboard to enter your destination or to find items in a list, like POIs.

Note: The keyboard does not include accents of any kind for any language as you don’t have to enter letters with accents. Simply type the letter without the accent and your GO will recognise it.

Note: This button is not available if you are using TomTom GO on devices without a touchscreen.

Manage maps

Manage maps

Tap this button to do the following:

• Download a map - you can buy new maps using TomTom HOME. For more

information, see Using TomTom HOME on page 63.

• Switch map - tap this button to change the map you are using.

• Delete a map - tap this button to create more space on your GO by deleting a map.

Don’t delete a map unless you have already made a backup of the map. If you delete a map before you make a backup, you won’t be able to put the map back on your GO.

For more information about making a backup, see Using TomTom HOME on page 63.

You can also download, add and delete maps using TomTom HOME.

Manage POIs

Manage POIs

Tap this button to do the following:

• Set alerts for when you are near POIs.

For example, your GO can tell you when there is a petrol station nearby.

• Create your own POI categories and add POIs to them.

For example, you could create a category of POIs called “Friends”, and add all your friends’ addresses as POIs in the category. You can even add your friends’ phone numbers with their address so you can call them from your GO.

For more information about POIs, see Points of Interest on page 36.

Status bar preferences

Status bar preferences

Tap this button to select the information shown on the status bar:

• Remaining time - the estimated time left until you reach your destination.

• Remaining distance - the distance left until you reach your destination.

• Arrival time - your estimated arrival time.

• Current time

Note: If you enter an arrival time when you plan your journey, the current

time is not shown. For more information, see Arrival times on page 21.

• Street name - the name of the next street to turn on to.

• Speed - your speed.

If the speed limit for road you are on is available, it is shown next to your speed.

If you drive faster than the speed limit, your speed is shown in red.

Note: The speed limit information is included with the map and is not available for all roads.

When you first start your TomTom GO, the remaining time, remaining distance, arrival time and the street name are shown.

Docking preferences

Docking preferences

Tap this button to set the following options:

• Turn brightness down when dark - your GO uses a light sensor to detect the background light level. If this option is selected, as it gets darker, your GO reduces the brightness of the screen so that it is not distracting.

• Switch to night view when dark - your GO uses a light sensor to detect the background light level. If this option is selected, when it gets dark, your GO uses night colours for the Driving View.

You can set the colour scheme by tapping Change map colours. For more

information, see Change map colours on page 58.

The next two options can only be used if you are using a TomTom accessory that enables your GO to communicate with your car.

• Link night view to headlights - if this option is selected, your GO will automatically use night colours when you switch the headlights on.

• Mute car radio - if this option is selected the car radio is muted when a spoken instruction is given.

Change map colours

Tap this button to select the colour schemes used for day and night map colours.

You can also download more colour schemes from TomTom PLUS. For more information, see the TomTom PLUS leaflet included with your product.

Change map colours

Brightness preferences

Brightness preferences

Tap this button to set the brightness of the screen. You can set the brightness separately for day map colours and for night map colours. You can also set these options:

You can set the map colour scheme by tapping Change map colours. For more

information, see Change map colours on page 58.

Planning preferences

Planning preferences

Tap this button to set the kind of route planned when you select a destination. The following options are available:

• Ask me every time I plan

• Always plan fastest routes

• Always plan shortest routes

• Always avoid motorways

• Always plan walking routes

• Always plan bicycle routes

• Always plan for limited speed

Toll road preferences

Toll road preferences

Tap this button to set how your GO handles toll roads if they are on the route to a destination you set.

You can choose always to avoid toll roads, never to avoid toll roads or to be asked what to do if a toll road is on the route planned.

If you set that your GO should ask you when there is a toll road on the route, you are asked whether you want to avoid the toll road as soon as you plan the route.

Compass preferences

Compass preferences

Tap this button to select whether a compass is shown and what the compass shows. The following options are available:

• One with arrow pointing north - the arrow always points north and the direction you are moving is at the top of the compass.

• One with arrow showing your heading - the arrow always shows the direction you are moving and the top of the compass is north.

If you select one of these options, you then choose what is shown in the middle of the arrow:

• Direction - the direction in which you are driving is shown in the centre of the compass, as a compass direction.

• Degrees - the direction in which you are driving is shown in the centre of the compass, in degrees.

• Nothing

• One with arrow pointing to your destination - the arrow always points to your destination relative to the direction you are travelling. The distance to your destination is shown in the middle of the arrow.

• None - no compass will be shown.

Set units

Set units

Tap this button to set the units used for the following:

• Distances

• Time

• Latitudes and longitudes

• Temperature

• Air pressure

Operate left-handed / Operate right handed

Operate lefthanded

Tap this button to move important buttons, for example, the Done and Cancel buttons as well as the zoom bar, to the left hand side of the screen. This makes it easier to tap the buttons with your left hand without blocking the screen.

To move the buttons back to the right hand side of the screen, tap Operate right-

handed.

Note: This button is not available if you are using TomTom GO on devices without a touchscreen.

Name preferences

Name preferences

Tap this button to set what is shown on the map in the Driving View. The following options are available:

• Show house numbers before street names

• Show street names

• Show next motorway / signpost - when this option is selected, the next major road on your route is shown at the top of the screen in the Driving View.

Hide tips / Show tips

Tap this button to stop your GO from giving you tips from time to time.

After you hide the tips, the button changes to Show tips. Tap this button to turn tips on again.

Hide tips

Set owner

Set owner

Tap this button to enter your name and address as the owner of your GO and to change or delete a 4-digit password for your GO.

You can create a 4-digit password for your GO using TomTom HOME:

1. Connect your GO to your computer and switch it on.

TomTom HOME starts automatically. For information about installing TomTom

HOME on your computer, see Installing TomTom HOME on page 63.

2. From the Options menu in TomTom HOME, click My GO.

3. Click the ON/OFF button on the picture of your GO to start the application on your computer.

4. From the Main Menu, click Change preferences.

5. Click Set Owner. You can now set a 4-digit password for your GO so that only you can use it.

You can only create a 4-digit password using TomTom HOME.

You can only change or delete a 4-digit password on your TomTom GO.

Speaker preferences

Speaker preferences

Tap this button to set whether music and spoken instructions should be played using the speaker in your GO or using an external speaker.

There are two options for these preferences:

• Play music over external speaker

• Play spoken instructions over external speaker

If you select either option, you must select which external speaker will be used.

You can use the speakers on your car stereo or Bluetooth Hi-Fi speakers.

For more information, see Sound on page 44.

Note: Music can only be stored and played using the GO 910.

Speech preferences

Speech preferences

Tap this button to change the information given by spoken instructions.

If you are using a computer voice, the voice can, for example, read aloud street names, messages and warnings. Computer voices are not available in all languages or on all devices.

You can also change the information a human voice gives you, but there are fewer options.

For more information, see Sound on page 44.

Note: Computer voices are only available on the GO 910.

Change driver ID

Tap this button to change the your driver ID.

Enter your driver ID, then tap Done.

Change driver

Start-up preferences

Start-up preferences

Tap this button to set what your GO should do when you first switch it on. The following options are available:

• Show odometer - your GO starts showing the odometer.

• Continue where I left off - your GO starts as it was when you switched it off.

• Ask for a destination - your GO starts with Navigate to... menu. You can enter a destination immediately.

• Show the Main Menu - your GO starts with the Main Menu.

Bluetooth preferences

Bluetooth preferences

Tap this button to disable or enable Bluetooth functionality on your GO. Tap

Advanced to set what the Bluetooth connection with your phone can be used for.

There are two options you can enable or disable separately:

• Enable wireless data

• Enable hands-free calling

In some places, such as hospitals and aeroplanes, you are required to turn

Bluetooth off on all electronic devices.

Do not ask arrival time / Ask arrival time

Do not ask arrival time

Tap this button to stop your GO from asking you if you want to arrive by a particular time whenever you plan a route.

To turn this option on again, tap Ask arrival time.

For more information, see Arrival times on page 21.

Reset factory settings

Tap this button to restore the factory settings to your TomTom GO. All your settings, including Favourites, your Home location, warnings for POIs and any

Itineraries you have created, as well as recent destinations and recent calls and callers, will be deleted.

Reset factory settings

Using TomTom HOME

Chapter 24 Using TomTom HOME

Using TomTom HOME, you can, for example, do the following:

• Make and restore backups of your TomTom GO.

• Manage the maps, voices, POIs and other extras on your GO.

• Read the full version of the user manual, available in 21 languages.

• Plan journeys in advance.

• Buy TomTom PLUS services and manage your subscriptions.

Installing TomTom HOME

To install TomTom HOME, put the CD which came with your GO into your computer.

If the installation does not start, browse to the CD on your computer and doubleclick the file Install TomTom HOME.

Connect the Home Dock to your computer using the USB cable and place your

TomTom GO in the Home Dock.

Making a backup

One of the most important things you can do with TomTom HOME is make a backup of your TomTom GO.

1. Connect your GO to your computer using the Home Dock and switch it on.

TomTom HOME starts.

2. Click Backup under Contents.

3. Click Backup.

TomTom HOME makes a backup of your GO on your computer.

Restoring a backup

If you ever have a problem with your GO, you can restore the backup.

Follow steps 1 and 2 above, then select the latest backup and click Restore.

The latest backup will be restored to your GO.

For more information, see the Help included with TomTom HOME.

Chapter 25 How does navigation work?

Global Positioning System (GPS)

In order to navigate you to your destination, your TomTom GO must know where you are now. To find your current position, your TomTom GO uses the Global

Positioning System (GPS). GPS is available for free and without subscription.

The GPS uses satellites to transmit signals to GPS receivers. Your TomTom GO has a built-in GPS receiver. Using the GPS signal, your TomTom GO can work out where you are and how fast you are going. GPS signals work in all weather, anywhere in the world.

Maps

Once your GO knows where you are and you have told it where you want to go, it uses the digital map on the memory card to work out the best route to your destination.

Chapter 26 TomTom limited warranty

WARRANTOR

Non-U.S. and non-Canadian purchases: If you have made your purchase outside the United States and Canada, this Limited Warranty is granted by and this

Limitation of Liability is stipulated for the benefit of TomTom International B.V.,

Rembrandtplein 35, 1017 CT Amsterdam (The Netherlands).

WHAT THIS WARRANTY COVERS

1) TomTom International B.V. (“TomTom”) warrants to you that the Hardware will be free from defects in workmanship and materials under normal use (“Defects”) for a period of two (2) years from the date that the Hardware was first purchased by you (“Warranty Period”). During the Warranty Period the Hardware will be repaired or replaced at TomTom’s choice (“Limited Warranty”) without charge to you for either parts or labour. This Limited Warranty covers the replacement of the

Hardware only. If the Hardware is repaired after the Warranty Period has expired, the Warranty Period for the repair will expire six (6) months after the date of repair.

WHAT THIS WARRANTY DOES NOT COVER

2) The Limited Warranty does not apply to normal wear and tear, does not apply when the Hardware is opened or repaired by someone not authorized by TomTom and does not cover repair or replacement of any Hardware or part thereof damaged by: misuse, moisture, liquids, proximity or exposure to heat and accident, abuse, non-compliance with the instructions supplied with the

Hardware, neglect or misapplication. The Limited Warranty does not cover physical damage to the surface of the Hardware. This Limited Warranty does not cover any software that may accompany or be installed on the Hardware.

HOW TO MAKE A WARRANTY CLAIM

3) In order to make a claim of a Defect, you must contact TomTom by email during the Warranty Period via www.tomtom.com to explain the Defect and to obtain an

RMA number (Return Materials Authorization) if necessary. You must return the

Hardware during the Warranty Period, along with an explanation of the Defect, to the address provided to you by TomTom. If a defect arises and a valid claim under this Limited Warranty is received by TomTom after the first one hundred and eighty

(180) days of the Warranty Period, TomTom is entitled to charge you for any reasonable shipping and handling costs made in connection with the repair or replacement of the Hardware. You must comply with any other return procedures stipulated by TomTom, if any.

YOUR LEGAL RIGHTS

4) Some countries may not allow the exclusion or limitation of damages. If any part of this Limited Warranty is held to be invalid or unenforceable, the remainder of the Limited Warranty shall nonetheless remain in full force and effect.

5) This Limited Warranty is the only express warranty made to you and is provided in lieu of any other express warranties or similar obligations (if any) created by any advertising, documentation, packaging, or other communications.

6) Except for the Limited Warranty and to the maximum extent permitted by applicable law, TomTom and its suppliers provide the Hardware “AS IS AND WITH

ALL FAULTS”, and hereby disclaim all other warranties and conditions, whether express, implied or statutory, including, but not limited to, any (if any) implied warranties, duties or conditions of satisfactory quality, of fitness for a particular purpose, of reliability or availability, of accuracy or completeness of responses, of results, of workmanlike effort, of lack of viruses, and of reasonable care and skill, all with regard to the Hardware, and the provision of or failure to provide support or other services, information, software, and related content through the

Hardware or otherwise arising out of the use of the Hardware. Also, there is no warranty or condition of quiet enjoyment, quiet possession, or non-infringement with regard to the Hardware. This exclusion does not apply to (i) any implied condition as to title and (ii) any implied warranty as to conformity with description.

7) This Limited Warranty does not affect any legal rights under applicable national legislation governing the sale of consumer goods.

8) This Limited Warranty cannot be transferred to any other person.

LIMITATION OF LIABILITY

9) Neither TomTom nor its suppliers shall be liable to you or to any third party for any damages either direct, indirect, incidental, consequential or otherwise

(including in each case, but not limited to, damages for the inability to use the equipment or access data, loss of data, loss of business, loss of profits, business interruption or the like) arising out of the use of or inability to use the Hardware even if TomTom has been advised of the possibility of such damages.

10) Notwithstanding any damages that you might incur for any reason whatsoever

(including, without limitation, all damages referenced herein and all direct or general damages in contract or anything else), the entire liability of TomTom and any of its suppliers shall be limited to the amount actually paid by you for the

Hardware.

11) TomTom shall not be liable for (i) any fraud on the part of its employees and/ or agents; or (ii) any fraudulent misrepresentation on the part of its employees and/or agents.

12) Notwithstanding the above, neither party’s liability for death or personal injury resulting from its own negligence shall be limited.

Battery notes

Chapter 27 Battery notes

We recommend that you fully charge your TomTom GO the first time that you connect it to the home dock. It takes about 2 hours to charge the battery completely.

Note: Your TomTom GO uses a small amount of battery power to maintain its state when you switch it off. If you do not charge it for a prolonged period of time then you will lose this state and your TomTom GO will re-start. Your settings will however, be maintained.

Addendum

Chapter 28 Addendum

Important Safety Notices and Warnings

Global Positioning System

The Global Positioning System (GPS) is a satellite-based system that provides location and timing information around the globe. GPS is operated and controlled under the sole responsibility of the Government of the United States of America which is responsible for its availability and accuracy. Any changes in GPS availability and accuracy, or in environmental conditions, may impact the operation of your TomTom GO. TomTom International B.V. and TomTom, Inc. cannot accept any liability for the availability and accuracy of GPS.

Use with Care

Use of TomTom GO for navigation still means that you need to drive with due care and attention.

Aircraft and Hospitals

Use of devices with an antenna is prohibited on most aircraft, in many hospitals and in many other locations. TomTom GO must not be used in these environments.

Battery

This product uses a Lithium-Ion battery. Do not use it in a humid, wet and/or corrosive environment. Do not put, store or leave your product in or near a heat source, in a high temperature location, in strong direct sunlight, in a microwave oven or in a pressurized container, and do not expose it to temperatures over 60 C

(140 F). Failure to follow these guidelines may cause the Lithium-Ion battery to leak acid, become hot, explode or ignite and cause injury and/or damage. Do not pierce, open or disassemble the battery. If the battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical attention immediately. For safety reasons, and to prolong the lifetime of the battery, charging will not occur at low (below 0 C/32 F) or high (over 45 C/113 F) temperatures.

Temperatures: Standard operation: -10 C (14 F) to +55 C (131 F); short period storage: -20 C (-4 F) to + 60 C (140 F); long period storage: -20 C (-4 F) to +25 C

(77 F).

THE LITHIUM-ION BATTERY CONTAINED IN THE PRODUCT MUST BE

RECYCLED OR DISPOSED OF PROPERLY. USE TOMTOM GO ONLY WITH

THE SUPPLIED DC POWER LEAD (CAR CHARGER/BATTERY CABLE)

AND AC ADAPTER (HOME CHARGER) FOR BATTERY CHARGING.

To recycle your TomTom GO unit please see your local approved TomTom service center.

SPECIAL NOTE REGARDING DRIVING IN CALIFORNIA

California Vehicle Code Section 26708 (a) (1) provides that "No persons shall drive any motor vehicle with an object or material placed, displayed, installed, affixed,

or applied upon the windshield or side or rear windows." Drivers in California should not use a suction mount on their windshield, side or rear windows.

TomTom Inc. bears no responsibility for any fines, penalties or damage that may be incurred by disregarding this notice. While driving in California, TomTom recommends the use of its Alternative Mounting Kit, which includes options for mounting TomTom devices on the dashboard and using the air vents. See www.tomtom.com for more information about this mounting option.

Note: this section of the California Vehicle Code applies to anyone driving in

California, not just California residents.

FCC Information for the User

The device used for this transmitter must not be co-located simultaneously operating in conjunction with any other transmitter.

Exposure to Radio Frequency Radiation

Except for the Remote Control unit the following applies to the other parts: To comply with RF exposure requirements please maintain a separation distance of at least 20 cm / 7 inches from any part of the product.

Radio and Television Interference

This equipment radiates radio frequency energy and if not used properly - that is, in strict accordance with the instructions in this manual - may cause interference to radio communications and television reception.

It has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation distance between the equipment and the receiver.

• If you are using the equipment with a mains adapter, plug it into an outlet which is on a different circuit from that to which the receiver is connected.

• Consult an experienced radio/TV technician for help.

Important

This equipment was tested for FCC compliance under conditions that included the use of shielded cables and connectors between it and the peripherals. It is important that you use shielded cable and connectors to reduce the possibility of causing radio and television interference. Shielded cables, suitable for the product range, can be obtained from an authorised dealer. If the user modifies the equipment or its peripherals in any way, and these modifications are not approved by TomTom, the FCC may withdraw the user’s right to operate the equipment. For customers in the USA, the following booklet prepared by the Federal

Communications Commission may be of help: “How to Identify and Resolve

Radio-TV Interference Problems”. This booklet is available from the US

Government Printing Office, Washington, DC 20402. Stock No 004-000-00345-4.

FCC Declaration of Conformity

Tested to Comply with FCC Standards for Home or Office Use

TomTom GO has been tested to – and complies with – part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Responsible party in North America

TomTom, Inc., 150 Baker Avenue, Concord, MA 01742

Tel: 866 48-6866 option 1 (1-866-4-TOMTOM)

Emissions information for Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CE Marking

This equipment complies with the requirements for CE marking when used in a residential, commercial, vehicular or light industrial environment.

R&TTE Directive

This equipment complies with the essential requirements of EU Directive 99/5/EC

(declaration available at www.tomtom.com).

Diese Ausrüstung erfüllt die wesentlichen Anforderungen der EU-Richtlinie 99/5/

EC (Erklärung verfügbar unter www.tomtom.com).

Cet équipement remplit les conditions édictées dans la Directrive EC/99/5

(document disponible sur www.tomtom.com).

Deze apparatuur is conform de eisen van de EU-richtlijnen 99/5/EC (verklaring beschikbaar op www.tomtom.com).

Questa apparecchiatura soddisfa le condizioni essenziali della Direttiva Europeea

99/5/EC (dichiarazione disponibile su www.tomtom.com).

Este equipo cumple con los requisitos esenciales de la Directiva 99/5/EC de la EU

(declaración disponible en www.tomtom.com).

Dette udstyr overholder de grundlæggende krav i EU-direktiv 99/5/EC (erklæring herom kan findes på www.tomtom.com).

Denna utrustning rättar sig efter de nödvändiga krav från EU direktiv 99/5/EC

(deklaration finns på www.tomtom.com).

Tämä laite täyttää oleellisilta osin EU:n direktiivin 99/5/EY vaatimukset

(vaatimustenmukaisuusvakuutus on nähtävänä osoitteessa www.tomtom.com).

Este equipamento está em conformidade com os requisitos essenciais da

Directiva da UE 99/5/CE (declaração disponível em www.tomtom.com).

TomTom tímto prohlašuje, že TomTom GO je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1995/5/ES (NV č. 426/2000 Sb.) a

Prohlášení o shodě je k dispozici na www.tomtom.com. Toto zařízení lze provozovat v České republice na základě generální licence č. GL - 12/R/2000.

Seadmed vastavad EL direktiivi 99/5/EÜ põhinõuetele (vt www.tomtom.com).

A jelen berendezés megfelel az EU 99/5/EC direktívája meghatározta szükséges előírásoknak (a nyilatkozat a www.tomtom.com honlapon található).

Ši įranga atitinka visus ES direktyvos 99/5/EB reikalavimus (deklaracijos tekstas tinklapyje www.tomtom.com).

Šis produkts atbilst visām ES noteiktajām Direktīvām 99/5/EC (deklarācija ir pieejama www.tomtom.com ).

Sprzęt ten jest zgodny z podstawowymi wymaganiami Dyrektywy UE 99/5/EC

(deklarację mozna pobrać ze strony internetowej www.tomtom.com).

TomTom týmto vyhlasuje, že TomTom GO spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1995/5/ES (NV č.443/2001 Z.z.) a Vyhlásenie o zhode je k dispozícii na www.tomtom.com. Toto zariadenie je možné prevádzkovat‘ v Slovenskej republike na základe Všeobecného povolenia č. VPR-

01/2001.

Bu cihaz AB Direktifi 99/5/AT'nin (beyanat www.tomtom.com adresinde mevcuttur) zorunlu gerekliliklerine uygundur.

WEEE Directive

In line with EU Directive 2002/96/EC for waste electrical and electronic equipment (WEEE), this electrical product must not be disposed of as unsorted municipal waste. Please dispose of this product by returning it to the point of sale or to your local municipal collection point for recycling. For more information, see www.tomtom.com

In Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen Parlaments und des Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses

Elektrogerät nicht im normalen Hausmüll oder dem Gelben Sack entsorgt werden.

Wenn Sie dieses Produkt entsorgen möchten, bringen Sie es bitte zur

Verkaufsstelle zurück oder zum Recycling-Sammelpunkt Ihrer Gemeinde. Weitere

Informationen hierzu finden Sie unter www.tomtom.com

Conformément à la Directive 2002/96/EC sur les déchets d’équipements

électriques et électroniques (DEEE), ce produit électrique ne doit en aucun cas être mis au rebut sous forme de déchet municipal non trié. Veuillez vous débarrasser de ce produit en le renvoyant à son point de vente ou au point de ramassage local dans votre municipalité, à des fins de recyclage. Pour plus d’informations, consultez le site www.tomtom.com

In navolging van richtlijn 2002/96/EG van het Europees Parlement en de Raad betreffende afgedankte elektrische en elektronische apparatuur (AEEA) mag dit elektrische product niet als ongescheiden huisvuil worden weggedaan. Breng dit product terug naar de plaats van aankoop of naar het gemeentelijke afvalinzamelingspunt voor recycling. Kijk voor meer informatie op www.tomtom.com

In ottemperanza alla Direttiva UE 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE), questo prodotto elettrico non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire il prodotto riportandolo al punto vendita o al punto di raccolta municipale locale per un opportuno riciclaggio. Per ulteriori informazioni, consultare il sito www.tomtom.com

De conformidad con la Directiva 2002/96/CE de la UE sobre residuos de aparatos eléctricos y electrónicos (RAEE), este producto eléctrico no puede desecharse con el resto de residuos no clasificados. Deshágase de este producto devolviéndolo al punto de venta o a un punto de recogida municipal para su reciclaje. Si desea más información, visite www.tomtom.com

I henhold til EU-direktiv 2002/96/EF om affald af elektrisk og elektronisk udstyr

(WEEE) må dette udstyr ikke bortskaffes som usorteret husholdningsaffald.

Bortskaf dette produkt ved at returnere det til salgsstedet eller til det lokale indsamlingssted, så det kan genbruges. Besøg www.tomtom.com for at få flere oplysninger.

I linje med EU-direktiv 2002/96/EG om avfall som utgörs av eller innehåller elektriska eller elektroniska produkter (WEEE) får denna elektriska produkt inte

bortskaffas som osorterat kommunalt avfall. Bortskaffa den i stället genom att lämna in den på försäljningsstället eller din lokala återvinningsstation. Se www.tomtom.com för mer information.

EU:n sähkö- ja elektroniikkalaiteromudirektiivin (2002/96/EY) mukaisesti tätä elektroniikkalaitetta ei saa laittaa lajittelemattoman yhdyskuntajätteen sekaan.

Hävitä laite palauttamalla se ostopaikkaan tai viemällä se elektroniikkaromun keräyspisteeseen. Lisätietoja löydät osoitteesta www.tomtom.com

De acordo com a Directiva Europeia 2002/96/EC sobre resíduos sólidos de equipamento eléctrico e electrónico (WEEE), este produto eléctrico não pode ser deitado fora juntamente com o lixo municipal indiferenciado. Por favor, no final da vida útil deste produto, devolva-o ao estabelecimento de aquisição, ou entregueo no local de recolha apropriado para reciclagem designado pelo seu município.

Para obter mais informações, consulte o endereço www.tomtom.com

V souladu se směrnicí EU č. 2002/96/ES o odpadních elektrických a elektronických zařízeních (OEEZ) se tento elektrický výrobek nesmí likvidovat jako netříděný komunální odpad. Při likvidaci tento výrobek vrat‘te prodejci nebo ho odevzdejte k recyklaci do komunálního sběrného zařízení. Další informace najdete na stránkách www.tomtom.com

Vastavalt EL direktiivile 2002/96/EÜ, mis käsitleb elektri- ja elektroonikaseadmete jäätmeid (WEEE), ei või antud toodet visata majapidamisjäätmete hulka. Palun tagastage antud toode taaskasutamise eesmärgil müügipunkti või kohaliku piirkonna jäätmekogumise punkti. Täiendava teabe kohta vt www.tomtom.com

Az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK

(WEEE) irányelvnek megfelelően ezt az elektromos berendezést tilos szortírozatlan, közösségi hulladékgyűjtőbe dobni. A terméket használata befejeztével vigye vissza az eladási ponthoz vagy a helyi közigazgatási

újrahasznosító gyűjtőhelyre. További információkat a www.tomtom.com honlapon találhat.

Pagal ES Direktyvą 2002/96/EB dėl elektros ir elektroninės įrangos atliekų (WEEE),

šio elektros gaminio negalima išmesti su buitinėmis atliekomis. Šį gaminį reikia grąžinti į tą vietą, kur jis buvo pirktas, arba į miesto atliekų perdirbimo punktą.

Daugiau informacijos pateikta www.tomtom.com

Saskaņā ar ES Direktīvu 2002/96/EC par elektrisko un elektronisko iekārtu atkritumiem (EEIA), šo elektrisko iekārtu ir aizliegts nodot kopā ar citiem nešķirotiem sadzīves atkritumiem. Lūdzu nododiet šo iekārtu atpakaļ tās tirdzniecības vietā vai Jūsu tuvākajā sabiedriskajā iekārtu savākšanas punktā to pārstrādei. Sīkākai informācijai, skatieties www.tomtom.com

Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie zużytego sprzętu elektrycznego i elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać jako nie posortowanego odpadu komunalnego. Prosimy o usuniecie niniejszego produktu poprzez jego zwrot do punktu zakupu lub oddanie do miejscowego komunalnego punktu zbiórki odpadów przeznaczonych do recyklingu. W celu uzyskania blizszych informacji prosimy o przejście na stronę www.tomtom.com

V súlade so smernicou 2002/96/ES o odpade z elekrických a elektronických zariadení (OEEZ) sa toto elektrické zariadenie nesmie odstranovat‘ ako netriedený komunálny odpad. Výrobok odstránte jeho vrátením v mieste nákupu alebo odovzdaním v miestnom zbernom zariadení na recyklovanie. Viac informácií zíkskate na internetovej adrese www.tomtom.com

Atık elektrikli ve elektronik cihazlar konulu 2002/96/AT sayılı AB Direktifine (WEEE) uygun olarak bu cihaz, ayrılmamış belediye atıklarıyla birlikte atılmamalıdır. Lütfen bu ürünü, satış noktasına iade ederek veya belediyenizin geri dönüşüm için toplama merkezine götürerek atın. Daha fazla bilgi için, www.tomtom.com adresini ziyaret edin.

Ctick

N14644

This product displays the Ctick to show it complies with all relevant

Australian and New Zealand regulations.

This Document

Great care was taken in preparing this manual. Constant product development may mean that some information is not entirely up-to-date. The information in this document is subject to change without notice.

TomTom International B.V. shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the performance or use of this material. This document contains information protected by copyright. No part of this document may be photocopied or reproduced in any form without prior written consent from TomTom International

B.V.

Part numbers

TomTom GO 715: 4V09.000

Chapter 29 Copyright notices

TomTom and the TomTom logo are registered trademarks of TomTom International B.V., The Netherlands. All other trademarks are the property of their respective owners.

Our end user license agreement and a limited warranty apply to this product; they are included in this package. You can also review both at www.tomtom.com/legal

Data Source

This product includes mapping data licensed from Ordnance Survey with the permission of the Controller of

Data Source

Apple® and iPod® are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Audible®, AudibleListener® and Audiblemanager® are registered trademarks of Audible, Inc. When purchasing and using Audible content you need to agree to the terms and conditions as posted in the Legal

Notices www.audible.com.

Some images are taken from NASA’s Earth Observatory.

The purpose of NASA’s Earth Observatory is to provide a freely-accessible publication on the Internet where the public can obtain new satellite imagery and scientific information about our home planet.

The focus is on Earth’s climate and environmental change. http://earthobservatory.nasa.gov/