Imagine Communications IconMaster Master Control Switcher Installation and Configuration Manual
Reklama
Reklama
Installation and Configuration Manual
Nexio® IconMaster™
Master Control Switcher
Software Release Version 3.9
September 2014
175-000287-00
Publication Information
© 2014 Imagine Communications Corp. Proprietary and Confidential.
Imagine Communications considers this document and its contents to be proprietary and confidential. Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine
Communications. All others uses are illegal.
This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product.
Trademarks
IconMaster
TM
and D-series are trademarks of Imagine Communications or its subsidiaries.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation. AMD and
Opteron are trademarks of Advanced Micro Devices, Inc. Dolby Digital is a registered trademark of Dolby Laboratories. Java is a trademark of Sun Microsystems, Inc. or its subsidiaries in the
United States and other countries.All other trademarks and trade names are the property of their respective companies.
Contact Information
Imagine Communications has office locations around the world. For locations and contact information see:
http://www.imaginecommunications.com/contact-us/
Support Contact Information
For support contact information see:
Support Contacts: http://www.imaginecommunications.com/services/technical-support/ eCustomer Portal: http://support.imaginecommunications.com
Contents
Preface
..........................................................................................................................xi
Chapter 1 Introduction
............................................................................................................... 1
Chapter 2 Installation
................................................................................................................. 7
iii
iv
Contents
Connecting the Main Panel and Optional Audio Panel .............................................12
Installing Standard NEO Modules (MKE-3901 and MGI-3903) ..................................20
Installing Optional NEO Modules (MKE-3901-FX and MKA-3901) .............................24
Connecting Optional GPI Input and Output Devices ................................................45
Chapter 3 Module Configuration
...........................................................................................53
Chapter 4 Router Connections
...............................................................................................61
Sample Configuration 1: IconMaster System with Internal
Video NSM Router and Optional ICONM-BO-V Module ............................................62
Sample Configuration 2: IconMaster System with Single Channel Audio and Video NSM
IconMaster
Installation and Configuration Manual
v
Routers and Optional ICONM-BO-VAC Module ....................................................... 66
Sample Configuration 3: IconMaster System with Internal (Two Channel) Audio and
Video NSM Routers and Optional ICONM-BO-VAC Module ..................................... 70
Sample Configuration 1: IconMaster System, External Panacea Video Router, Optional
Sample Configuration 2: IconMaster System, External Panacea
Video Router, Optional ICONM-BO-V Module, Optional
Sample Configuration 3: IconMaster System, External Panacea
Clean/Quiet Switch Video Router, Optional ICONM-BO-V Module,
Sample Configuration 5: IconMaster System with External
Panacea (Two Channel) Audio and Video Routers, Optional
ICONM-BO-VAC Module, Optional SPT-LSERIAL ...................................................... 87
Sample Configuration 1: IconMaster System, External Platinum Router, Optional
Sample Configuration 2: IconMaster System, External Platinum Router, HView SX
Hybrid, JLCooper eBOX, ICONM-BO-V Module ........................................................ 94
Chapter 5 Configuring IP Addresses
.................................................................................... 99
Chapter 6 Connecting an IconMaster to an EAS Device
............................................ 103
Chapter 7 Machine Control
vi
Contents
Chapter 8 Logging Server
.......................................................................................................109
Configuring IconMaster for Magellan Logging Server .............................................110
Changing Columns That Appear in Magellan Logging Server .................................118
Interpreting IconMaster Messages in the Logging Server .....................................119
Chapter 9 Automation Setup
................................................................................................121
Connecting a DAL Automation System to IconMaster ...........................................121
Configuring IconMaster to Ignore Automation Commands on Specific Key Layers ..
127
Important Considerations for Automation Key Masks .............................................129
Chapter 10 Configuring IconMaster
.....................................................................................131
IconMaster
Installation and Configuration Manual
vii
Chapter 11 Enabling a Router Database for Use with an IconMaster System
..........
199
viii
Contents
Chapter 12 Troubleshooting
....................................................................................................219
Cannot PING the IconMaster Components From a Computer .................................220
RCP Cannot Connect To An IconMaster Channel (MKE) .........................................221
Chapter 13 Specifications
.........................................................................................................225
IconMaster
Installation and Configuration Manual
ix
Index
......................................................................................................................... 233
x
Contents
Preface
Manual Information
Purpose
This manual details the features, installation procedures, configuration procedures, and specifications of the Nexio® IconMaster™ master control switcher.
Audience
This manual is written for engineers, technicians, and operators responsible for the installation and setup of the IconMaster master control switcher.
Revision History
Table 2-1 Revision History
Edition
Preliminary 1
Preliminary 2, for use with System
Software Release 1.0.1
Edition A, for use with System
Software Release 1.1
Edition B, for use with System
Software Release 1.2
Software Contents
Content Editor 1.0.0
LogoCreator 3.1.1
IconMaster GUI 1.0.0
IconSet Configuration Utility 1.0.0
Content Editor 1.0.0
LogoCreator 3.1.1
IconLogo SoftPanel 1.0.0
IconSet Configuration Utility 1.0.0
Content Editor 1.0.0
LogoCreator 3.1.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility
1.0.0.48
Content Editor 1.0.0
LogoCreator 3.1.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility
1.0.0.62
Date
December 2005
February 2006
March 2006
June 2006 xi
xii
Preface
Table 2-1 Revision History (Continued)
Edition
Edition C, for use with System
Software Release 1.4
Edition D, for use with System
Software Release 1.5
Edition E, for use with System
Software Release 2.0
Edition F, for use with System
Software Release 2.0.1
Edition G, for use with System
Software Release 2.1
Edition H, for use with System
Software Release 2.20
Edition I, for use with System
Software Release 3.0
Edition J, for use with System
Software Release 3.1
Edition K, for use with System
Software Release 3.2
Edition L, for use with System
Software Release 3.2.1
Software Contents
Content Editor 1.0.0
LogoCreator 3.1.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility
1.0.0.70
Content Editor 1.0.0
LogoCreator 3.1.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility 1.5.0.3
Content Editor 1.0
LogoCreator 4.0
IconLogo SoftPanel 1.0
IconMaster Configuration Utility 2.0
Content Editor 1.0
LogoCreator 4.0
IconLogo SoftPanel 1.0
IconMaster Configuration Utility 2.0.1
Content Editor 1.1
LogoCreator 4.0
IconLogo SoftPanel 1.0
IconMaster Configuration Utility 2.1
Content Editor 1.1
LogoCreator 4.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility 2.2
Content Editor 1.1
LogoCreator 4.1
IconLogo SoftPanel 1.0.7
IconMaster Configuration Utility 3.0
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.1
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.2
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.2.1
Date
September 2006
December 2006
May 2007
June 2007
July 2007
March 2008
June 2008
January 2009
February 2010
May 2010
IconMaster
Installation and Configuration Manual
xiii
Table 2-1 Revision History (Continued)
Edition
Edition M, for use with System
Software Release 3.2.x
Edition N, for use with System
Software Release 3.3
Edition O, for use with System
Software Release 3.4
Edition P, for use with System
Software Release 3.5
Edition Q, for use with System
Software release 3.6
Edition R, for use with System
Software release 3.7
Software release version 3.8
Software release version 3.9
Software Contents
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.2.x
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.3
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.4
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.5
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.6
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.7
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.8
Content Editor 1.3.1
LogoCreator 4.2
IconLogo SoftPanel 1.09
IconMaster Configuration Utility 3.9
Date
May 2010
February 2011
April 2011
October 2012
June 2013
July 2013
June 2014
June 2014
xiv
Preface
Writing
Conventions
To enhance your understanding, the authors of this manual have adhered to the following text conventions:
Table 2-2 Writing Conventions
Term or
Convention
Bold
Description
Italics
Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names
Indicates E-mail addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis
CAPS
Code
Indicates a specific key on the keyboard, such as ENTER, TAB,
CTRL, ALT, or DELETE
Indicates variables or command-line entries, such as a DOS entry or something you type into a field
> hyperlink
Indicates the direction of navigation through a hierarchy of menus and windows
Indicates a jump to another location within the electronic document or elsewhere
Internet address Indicates a jump to a Web site or URL
Indicates important information that helps to avoid and troubleshoot problems
Obtaining
Documents
Product support documents can be viewed or downloaded from our website. Alternatively, contact your Customer Service representative to request a document.
Unpacking/Shipping Information
Unpacking a
Product
This product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service.
1
Check equipment for any visible damage that may have occurred during transit.
2
Confirm that you have received all items listed on the packing list.
3
Contact your dealer if any item on the packing list is missing.
4
Contact the carrier if any item is damaged.
5
Remove all packaging material from the product and its associated components before you install the unit.
Keep at least one set of original packaging, in the event that you need to return a product for servicing.
IconMaster
Installation and Configuration Manual
xv
Product
Servicing
IconMaster systems are not designed for field servicing. Except for certain designated options as described in this manual, all hardware upgrades, modifications, or repairs require you to return the product to the Customer Service center.
Returning a
Product
In the unlikely event that your product fails to operate properly, please contact Customer
Service to obtain a Return Authorization (RA) number, then send the unit back for servicing.
Keep at least one set of original packaging in the event that a product needs to be returned for service. If the original package is not available, you can supply your own packaging as long as it meets the following criteria:
The packaging must be able to withstand the product’s weight.
The product must be held rigid within the packaging.
There must be at least 2 in. (5 cm) of space between the product and the container.
The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing.
Safety
Carefully review all safety precautions to avoid injury and prevent damage to this product or any products connected to it. If this product is rack-mountable, it should be mounted in an appropriate rack using the rack-mounting positions and rear support guides provided. It is recommended that each frame be connected to a separate electrical circuit for protection against circuit overloading. If this product relies on forced air cooling, it is recommended that all obstructions to the air flow be removed prior to mounting the frame in the rack.
If this product has a provision for external earth grounding, it is recommended that the frame be grounded to earth via the protective earth ground on the rear panel.
IMPORTANT! Only qualified personnel should perform service procedures.
Safety Terms and Symbols in this Manual
WARNING
Statements identifying conditions or practices that may result in personal injury or loss of life. High voltage is present.
CAUTION
Statements identifying conditions or practices that can result in damage to the equipment or other property.
Terms and Symbols on the Product
DANGER: High voltage; indicates a personal injury hazard immediately accessible as one reads the marking.
xvi
Preface
WARNING: Indicates a personal injury hazard not immediately accessible as one reads the marking.
CAUTION: Indicates a hazard to property including the product or to take Attention and refer to the manual.
Protective ground (earth) terminal.
Fuse. Replace with same type and rating of fuse.
Observe precautions for handling electrostatic sensitive devices.
Embedded Software License Agreement
The software embedded in this product incorporates the VxWorks Run-Time Module, and the following paragraphs are applicable. You are prohibited from:
a
copying the Run-Time Module, except for archive purposes consistent with your archive procedures;
b
transferring the Run-Time Module to a third party apart from the product containing the Run-Time Module;
c
modifying, decompiling, disassembling, reverse engineering or otherwise attempting to derive the source code of the Run-Time Module;
d
exporting the Run-Time Module or underlying technology in contravention of applicable U.S. and foreign export laws and regulations; and
e
using the Run-Time Module other than in connection with operation of the product in which it is embedded.
Any further distribution of the Run-Time Module is subject to the same restrictions set forth herein. Wind River Systems, Inc. and its licensors are third party beneficiaries of the End User
License Agreement and the provisions related to the Run-Time Module are made expressly for the benefit of, and are enforceable by, Wind River Systems, Inc. and its licensors.
The laws of the Province of Ontario shall govern this Agreement. Updated January, 2005.
1
Introduction
Overview
The IconMaster modular master control switcher provides, in a modular format, the ability to combine critical master control functions with multi-integrated branding. IconMaster is based on our industry-leading NEO modular platform. It is the only control that can be combined with other advanced applications to create a complete, self-contained channel release system.
This manual is part of a two-part set. Hardware installation and configuration procedures are provided in one manual, and control panel operation and configuration procedures are provided in the other manual. This manual provides detailed information on installing and configuring the hardware components in your IconMaster system. A complete setup will include
Installing the IconMaster control panel
Installing optional NEO modules
Mounting a NEO frame in a rack
Configuring NEO modules
Connecting internal or external routers
Connecting external Ethernet to serial and GPI interface devices
Configuring control panel components (this information is provided in a separate manual)
Control panel operations (this information is provided in a separate manual)
Optional software installation and operation (this information is provided in a separate manual)
Each of these topics is covered in the IconMaster manual set. In some cases, however, you will be referred to another manual for more detailed information.
1
2
Chapter 1
Introduction
Product Description
Figure 1-1 IconMaster RCP Control Panel (with Optional Audio Control Panel)
The IconMaster ICONM-RCP features a 12-input desk-mount or rack-mount control panel with LED buttons for bus selection and transitions as well as fully-configurable LCD buttons.
An “intelligent” audio control panel, and touch-screen configuration and control are available as options.
IconMaster
Installation and Configuration Manual
3
Figure 1-2 IconMaster ICONM-RCP16 Control Panel (with Optional Audio Control Panel)
The IconMaster ICONM-RCP16 features a 16-input desk-mount or rack-mount control panel with LED buttons for bus selection and transitions as well as fully-configurable LCD buttons. An “intelligent” audio control panel, and touch-screen configuration and control are available as options.
IconMaster is both SD and HD-ready. You can migrate from an SD master control to an HD master control via a straightforward configuration setting.
With IconMaster, flexibility is a core feature. With assignable, two-channel, squeeze back position, you have the power to choose. Internal or external routing is offered with 12 or 22 inputs, and with or without emergency bypass routing.
IconMaster features four internal and two external key layers for branding. Features supported include static and animated logos, analog and digital clock capability, crawls, EAS
(Emergency Alert System) and Amber Alert. The IconMaster is also available without internal logo branding layers. This product, IconMaster Lite, has two external key and fill inputs, and two Audio Over inputs. (The MGI-3903 IconLogo branding module is available as an upgrade for IconMaster Lite.)
4
Chapter 1
Introduction
Product Features
Main
Features
SD or HD configurable with no hardware changes
Upgrade from IconLogo branding to IconMaster Master Control
Assignable (two-channel) squeezeback position option
Desk- or rack-mount control panel
Industry-standard buttons with LEDs for bus selection and transitions
User configurable LCD buttons
Fader bar option
Multi-channel modular design
Two NEO-slot solution, or three slots with addition of audio monitoring option
(embedded audio with external routing)
Up to six channels in 3RU
Operate multiple channels from single panel
Full next-event preview
6 keyers
2 external, key/fill
4 internal branding keys
Static and animated logos
1
Analog and digital clocks
Text crawls and EAS/Amber Alert option
Flexible audio options
8 channels discrete AES audio
16 channels embedded audio
2 audio overs with dedicated EAS inputs
Passes non-PCM audio such as Dolby
® while processing PCM channels
-E and Dolby
®
AC-3 on selected channels
Full-channel audio assignment and processing
Internal audio logo playback by attaching .WAV files to a logo
Dynamic assignable audio profiles
Full support for CCS-P (i.e., Navigator and NUCLEUS) control
Machine control
Router control over Ethernet or serial RS-232/422
Drive under monitor displays using serial tally protocol
Aux bus support of multi-level sources and destinations
On-screen logo positioning
Internal logo memory storage expanded to 4 Gb (via the MGI-3903)
Primary/secondary assignment and control of up to eight IconMaster channels for slaved operation
Timer/clock on RCP
RCP available as SNTP time server from clock module reference
Assignable names to programmable Quick Select macro functions, and to GPO events
1
Not available on IconMaster Lite models.
IconMaster
Installation and Configuration Manual
5
Optional
Features
Fader bar
Intelligent audio control panel
Internal or external routing with 12, 16, or 22 inputs
External routing with or without emergency backup routing
Relay bypass with dedicated bypass input
2-channel video squeezeback option
Text crawl with dynamic data insertion
RSS and ODBC connectivity
EAS and Amber Alert (Emergency Alert System) insertion
Fully- featured “soft” control panel
Direct control of multiviewers
Up to 66 GPI inputs and up to 61 GPI outputs via the use of an optional Ethernet to serial and GPI interface
Support for any multiviewer on the market, with special support for HView SX Hybrid and Predator Multiviewers
IconMaster Components
A complete IconMaster setup consists of main components, optional items, NEO modules, and routers.
Main Components
Hardware Components
A main control panel with one power supply (For redundant power supply operation, two power supply units may be used)
A 3RU NEO frame with redundant power supplies
An MKE-3901 mixer/keyer module
An MGI-390x IconLogo graphics module
Software Components
Icon Series Soft Tools CD, which includes
IconMaster Configuration Utility (ICU)
Content Editor
LogoCreator
IconLogo Soft Panel
Optional Items
An additional power supply (for redundant power supply operation)
An audio control panel
An MKE-3901-FX effects optional submodule (for MKE-3901 module)
An MKA-3901 balanced audio module
An ICONM-BO-V video breakout module
6
Chapter 1
Introduction
A balanced (ICONM-BO-VAB) or a coaxial (ICONM-BO-VAC) audio/video breakout module
NEO 3901RES-E resource module for CCS-P control and display
An internal router, such as NEO NSM routers
An external router, such as Platinum, Integrator, or Panacea
A general purpose interface box, such as a JLCooper Electronics eBOX™ Quad Serial to
Ethernet Interface
1
System
Setup
The types of components and options you purchased will determine the complexity of your installation and configuration.
includes the sequences of events for
the most common IconMaster installation situations. Please see page 9 for a listing of these
scenarios.
About this Manual
This IconMaster manual involves hardware installation and configuration. Control panel operation, as well as icon software installation, configuration, and operation, are covered in a separate manual.
1 eBOX is a trademark of JLCooper Electronics
.
2
Installation
Overview
IconMaster is a cost-effective modular master control and branding solution beyond the conventional, offering the ability to combine critical master control functions with multi-layer integrated branding, all in a modular card format.
The IconMaster master control switcher is controlled by a control panel, automation, or general purpose inputs. This chapter is designed to help install and set up the IconMaster frame modules, control panel, and all relevant interconnections between the frame and panel.
Pre-Installation Information
IconMaster Main Components
Main control panel with one power supply
MKE-3901 mixer/keyer module
MGI-3903 IconLogo graphics module
IconMaster Soft Tools CD, including IconMaster configuration utility
The IconMaster configuration utility software requires a separate Pentium III 1GHz (or equivalent) PC with the following minimum requirements:
512 Mb RAM
10 Gb fixed disk drive space
10/100 Ethernet card
Microsoft
®
Windows
®
2000 or Windows XP
1 operating systems
Optional
Equipment
The following options are available for use with the IconMaster system. You may order these options separately and install them yourself, or you may order them at the same time as your
IconMaster system so that they will be factory-installed and -configured.
Additional power supply (for redundant power supply operation)
Audio control panel
1
Windows 2000 and Windows XP are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Currently the IconMaster utilities do not operate with Microsoft Vista operating system.
7
8
Chapter 2
Installation
Fader bar
MKE-3901-FX effects optional submodule (for MKE-3901 module)
MKA-3901-B balanced audio module
ICONM-BO-V video breakout module
ICONM-BO-VAB balanced audio breakout module
ICONM-BO-VAC coaxial audio breakout module
Internal routers (such as NEO NSM 7×2 routers)
External routers, including Platinum and Panacea routers, in addition to third-party routers
HView SX Hybrid multiviewer output module (in a Platinum frame)
Predator multiviewer
JLCooper Electronics eBOX Quad Serial to Ethernet Interface
1
Figure 2-1
shows how an IconMaster system setup works. Each installation component of this setup (except for the customer-supplied PC) is explained in more detail in sequent sections.
Figure 2-1 IconMaster Components
1
“eBOX” is a trademark of JLCooper Electronics, El Segundo, California, USA
IconMaster
Installation and Configuration Manual
9
Installation
Notes
All IconMaster components must be mounted in an area where there is unrestricted air movement. Except for the MKE, MGI, and MKA modules (which are mounted in standard NEO frames) no fan cooling is required.
The two control panels of the IconMaster system are designed for desk and tabletop operation, or for use in a standard equipment rack.
For maximum efficiency and reliability, IconMaster control panels should be operated in an ambient temperature between 68° and 86°F (20° to 30°C) non-condensing.
IconMaster control panels communicate with the MKE-3901 via an Ethernet network.
On the same network, the MGI-3903 also connects to the PC that hosts the IconMaster configuration utility software.
If your network includes a switch, the switch must be 10/100Base-T. The system will not function on 10Base-T or 100Base-T only.
Some consumer or SOHO network switches may fail to auto-negotiate Ethernet port configuration with IconMaster when repowering or rebooting. For best results, use a managed switch capable of port configuration, and configure the port to 100 Mbs
Full-Duplex if a failure to communicate after reboot occurs with any network switch.
A NEO resource module is not required for IconMaster to be configured and work correctly.
NEO frames require an ambient temperature between 32° and 122°F (0° and 45°C.)
See the technical manual of your PC for information on the operating temperatures of the computer.
NEO modules used in an IconMaster system must be connected together in the following top-to-bottom order before being inserted in a NEO frame:
1. MKA-3901 (optional)
2. MKE-3901 (with optional MKE-3901-FX submodule)
3. MGI-3903
Because the modules are physically connected together, they must all be installed on the same side of the frame.
CAUTION
If your IconMaster package was not factory-installed in a NEO frame, ensure that you use the provided screws to secure the modules together before they are inserted in the frame.
Sequence of
Events for
Installation
For a fully functional IconMaster system, you must install and configure the hardware components, and initialize certain settings. (Your particular installation may or may not include all of these steps, depending on which options you purchased.) After the installation is complete, you will need to configure the hardware modules, internal and external routers, and control panel components. These configuration tasks are explained in separate chapters.
Table 2-1 Sequence of Events for Installation
Step
1 Install fader bar (if ordered separately)
2(optional) If the audio control panel was purchased separately, connect main control panel to audio control panel
3 Mount the control panel(s) into a desktop or a rack
4 Connect the control panel to another device
For more information
10
Chapter 2
Installation
Table 2-1 Sequence of Events for Installation (Continued)
Step
5 Install NEO options into NEO frame (if ordered separately)
6 Install NEO frame into a rack
7 Install and configure internal or external routers
Configure internal NSM modules
OR
Install HView SX Hybrid into Platinum router (if ordered) and then mount external router in a rack
If it’s a Panacea router, configure it
If it’s a Platinum router and you’ll be using it with an eBOX, configure the eBOX after installing the router hardware.
Then configure the Platinum
Then configure HView SX Hybrid
8 Attach breakout modules
9 Connect the NEO modules to another device
10 Check card-edge parameters are set to your preferences
11 Configure IconMaster control panel
12 Initialize IconMaster
13 Customize push buttons on control panel
For more information
See HView SX Hybrid manual and/or router manual
page 69 page 147 page 126
Tools You
Will Need
The following is a list of tools and equipment you will need for a successful IconMaster installation. (Your particular installation may or may not require all of these items, depending on which options you purchased.)
Desk or table with cutout; use the dimensions found on page 15
OR
One standard 19-in. (0.4-m) rack and four to eight 40×1/4 flat-head screws
One medium Phillips screwdriver
For a direct setup (MKE-3901 directly to IconMaster control panel), one 36-in. (91-cm) crossover cable
For a network setup (IconMaster to Ethernet)
1 network hub, at least 10Base-T or 10/100Base-T
Standard 10 Mbps 10Base-T Ethernet cable segments no longer than 382.08 ft
(100 m) for IconMaster control panel, MKE-3901 module, and MGI-3903 module
RS-232 or TIA/EIA-422-B cable segment; no longer than 50 ft (15 m) for RS-232, and
2,000 ft (610 m) for TIA/EIA-422-B, for use with external router or automation control device
NEO FR-3901, FR-3903, and FR-3923 Mounting Frames Installation and Operation
Manual
Internal routing device module, as appropriate (NEO NSM-7×2SHD or NSM-7×2AES)
External routing device, as appropriate (Platinum, Panacea)
External routing device manual, as appropriate:
IconMaster
Installation and Configuration Manual
11
(For use with NSM-7×2SHD internal routers) NEO NSM-8×1SHD/NSM-7×2SHD SD/
HD Wideband Video Routing Switchers Installation and Operation Manual
(For use with NSM-7×2AES internal routers) NEO NSM-8×1EAS/NSM-7×2AES Serial
Digital Audio Routing Switchers Installation and Operation Manual
(For use with Platinum 9RU, 15RU, and 28RU frames) Platinum Series Frames and
Modules Installation, Configuration, and Operation Manual
(For use with Panacea frames) Panacea Series Frame and Modules Installation,
Configuration, and Operation Manual
(For use with optional HView SX Hybrid multiviewer) HView SX Hybrid Multiviewer
Installation, Configuration, and Operation Manual and HView SX Hybrid Layout
Designer User Guide
(For use with optional eBOX) eBOX Ethernet to Serial & GPI Interface Users Manual
Sample
System
Layout
Figure 2-2
shows a sample system layout that includes an external router, PC, Ethernet switch, and IconMaster system. For illustrations of sample system layouts for NEO routers, see
System Configurations—NEO Routers
on page 62. For illustrations of sample system
layouts for Panacea routers, see
System Configurations—NEO Routers
Figure 2-2 Sample System Layout
12
Chapter 2
Installation
Installing Control Panels
Connecting the Main Panel and Optional Audio Panel
The IconMaster main control panel and audio control panel are connected to each other both mechanically (by means of a bracket) and electrically (by using two wiring harnesses).
The audio control panel cannot operate independently of the main control panel, and must always be directly attached. If you ordered both controls at the same time, they will be preassembled at the factory.
If you ordered the control panels at different times you can connect them together yourself.
To connect the main control panel and audio control panel together, follow these steps:
1
Remove the four screws on each side of the main control panel trim (see
Remove these four screws
Replace three screws for the new trim
Figure 2-3 Removal of Trim
2
Replace the side trim with the two new shorter pieces supplied. Only three screws are required on each side to attach the new trim.
3
Remove the cover plate from the back of the main control panel (see
Remove cover plate
Figure 2-4 Removal of the Main Control Panel Cover Plate
4
Attach the audio control panel mounting bracket to the back of the main control panel, using the screws provided (see
).
IconMaster
Installation and Configuration Manual
13
Attach to the back of the main control panel
Figure 2-5 Audio Control Panel Mounting Bracket
5
Face the audio control panel down on top of the main control panel buttons. Attach the two ribbon cables from the main control panel to the audio control panel (see
Figure 2-6
).
Audio control panel folded over top of the main control panel
Base of main control panel
Ribbon cables
Figure 2-6 Ribbon Cable Between Main and Audio Control Panels
6
Attach the audio control panel to the mounting bracket by inserting the provided screws in the curved slots that overlap each side of the audio control panel (see
).
14
Chapter 2
Installation
Insert screw here
Insert screw here
Figure 2-7 Audio Control Panel Attachment
7
Set the audio control panel to the viewing angle that suits your needs, and then tighten the sliding screws.
Mounting the Control
Panels
The two control panels of the IconMaster system are designed for desk and tabletop operation, or for use in a standard equipment rack. Desk and tabletop mounting are
described on page 14; rack mounting is described on page 15.
Mounting Panels in a Desk or a Tabletop
The IconMaster control panels can be set into a desk or tabletop. (The optional audio control panel must be attached to the main control panel before you mount it; see
Connecting the Main Panel and Optional Audio Panel
Note: The control panels are easier to see and use if the tabletop or desk is angled towards the operator. For illustration purposes here, the trim has been removed. In a typical desk or tabletop installation, the trim will remain attached.
Follow these steps to mount the control panels into a desk or tabletop:
1
Using the dimensions shown in
(for the main control panel only) or
(for the main and audio control panels together), make a cutout in the desk or tabletop.
2
Carefully place the control panels into the cutout.
IconMaster
Installation and Configuration Manual
15
10.1
inches
(25.7 cm)
16.75 inches (42.6 cm)
Figure 2-8 Desk or Tabletop Mount of Main Control Panel Alone
5
6
4
3
2
1
Figure 2-9 Desk or Tabletop Mount of Main and Audio Control Panels
5
6
3
4
1
2
Width of panel left to right
Length of panel front to back (total)
16.75 inches (42.6 cm)
13.9 inches (35.3cm)
Length of panel front to back (underside)
10.1 inches (25.7cm)
Length of audio panel overhang
3.8 inches (9.6cm)
Panel depth (front)
3.5 inches (8.8 cm)
Panel depth (back)
2.1 inches (5.2 cm)
Mounting Control Panels into a Rack
Note: The main and audio control panels can be mounted in a rack with or without the outer trim attached. However, the outer trim will use an additional 1RU of extra space above and below the unit if it is left attached. If you choose to remove the trim, ensure that you replace the two middle screws found on each side (see
16
Chapter 2
Installation
To install the main control panel and the optional audio control panel in a rack, use the adjustable left and right-side frame mounting brackets that are provided. The brackets are designed so that you can angle the panels either upward or downward, according to your needs. (See
.) If you are using an audio control panel, attach and connect the
audio panel to the main control panel frame before you attach the brackets (see
Connecting the Main Panel and Optional Audio Panel
The following steps describe the installation of the control panels in a rack. If you do not
wish to remove the trim, start at step 6.
1
Remove the three or four screws on each side of the main control panel trim (see
)
Remove these four screws
Figure 2-10 Removal of Trim for Rack Mounting
2
Remove the trim pieces from the sides of the main control panel.
3
Remove the wrist rest from the bottom of the main control panel.
4
Replace the middle two screws on each side of the main control panel with 4-40×1/4 FH screws (see
4-40×1/4 FH screws
Figure 2-11 Main Control Panel Side Screws
5
If there is no audio control panel:
Remove the trim from the top of the main control panel.
If there is an audio control panel:
a
Remove the three screws on each side of the audio control panel trim.
b
Remove the trim from the sides of the audio control panel.
c
Remove the trim from the top of the audio control panel.
IconMaster
Installation and Configuration Manual
17
d
Replace the two screws on each side of the audio control panel with 4-40×1/4 FH screws (see
).
4-40×1/4
FH screws
Figure 2-12 Audio Control Panel Side Screws
6
Attach the mounting brackets to the sides of the main control panel using the screws provided (see
).
Attach 2 screws per side
Figure 2-13 Attaching the Rack-Mount Bracket
7
Loosen the screws on the sliders, and then reposition the sliders to change the viewing angle of the control panels (see
Tighten screws at the back of the slider
Figure 2-14 Adjustment of Slider Screws
18
Chapter 2
Installation
8
Tighten the slider screws and make all of the necessary cable connections on the back of the main control panel.
9
Align the control panel assembly so that the screw holes in the mounting brackets match up with those at the front of the rack.
10
Secure the control panel assembly to the rack with 10×32 machine-head mounting screws and washers.
11
Make necessary control panel connections (see page 18).
Connecting Main Control Panel Components
The IconMaster main control panel has external connections located in a bay on the underside of the unit (
Figure 2-16
). In addition, two 50-pin connectors at the back of the panel provide an interface with the optional audio control panel.
Figure 2-15 Main Control Panel External Connections—Older Models
Figure 2-16 Main Control Panel External Connections—Newer Models
The Timecode IN provides a means for IconMaster to read a facility time-of-day real-time clock. If desired, feed a unity speed, forward counting LTC timecode signal into the
Timecode IN connector, and configure the IconMaster to use the RCP panel as it's primary time-of-day clock source. A MTG-3901 module or CSD5300 product can be used for this timecode signal. DIP Switch 1 (below) is used to set the Timecode IN termination to either open or 600
. See page 182 to setup IconMaster to use the RCP's Timecode IN as the
real-time clock source.
Note: One RCP panel can be setup as the real-time clock source for multiple IconMaster channels.
The Timecode OUT connector is used to feed an external LTC timecode display device with a time function from the IconMaster. IconMaster can display either the time-of-day or its
segment timer on this output. See page 182 to set this up.
IconMaster
Installation and Configuration Manual
19
Figure 2-17 Timecode IN (Rear Panel View)
Figure 2-18 Timecode OUT (Rear Panel View)
DIP Switch Settings
The DIP switches on the main control panel allow you to set values for termination for timecode in (LTC) and for failsafe bootloader (CPU BOOT). DIP switch 1 controls the LTC setting and DIP switch 2 controls the CPU BOOT setting. See
the values of these settings.
Figure 2-19 DIP Switch Setting Values
Note: Failsafe mode is used only if the panel fails to load properly on power up. In this mode the file system can be manually restored. Contact customer service for additional details
Power Supply
The IconMaster main control panel uses one external power supply. (For redundant power supply operation, two power supply units must be used.)
20
Chapter 2
Installation
The DC output from one of the provided power supplies should be connected to PS1 on the IconMaster control panel. Connect the second, redundant power supply to PS2.
When you plug in the power supply, the IconMaster control panel buttons will light up. You may want to verify the IP address and software version for your system. This function is performed via the Service menu (see the IconMaster Function Operation and Configuration
Manual for instructions).
NEO Modules Connection (Not Connected to a Network)
The IconMaster main control panel can be connected directly to the system’s NEO frame-based modules when the system is not connected to a network. To do this, connect
Ethernet on the main control panel to Ethernet 1 on the MKE-3901 back module using a crossover (twisted) cable.
Network Connection
The IconMaster main control panel can be connected to a network system. To do this, connect Ethernet on the IconMaster main control panel (or Ethernet 2 on older panels) directly to a switch on the network using a straight cable.
Note:
Some consumer or SOHO network switches may fail to auto-negotiate Ethernet port configuration with IconMaster when repowering or rebooting. For best results, use a managed switch capable of port configuration, and configure the port to 100 Mbs
Full-Duplex if a failure to communicate after reboot occurs with any network switch.
Installing NEO Modules
Installing Standard NEO Modules (MKE-3901 and MGI-3903)
An IconMaster system includes an MKE-3901 mixer/keyer module and an MGI-3903
IconLogo graphics module as standard equipment. These modules and their corresponding back connector modules are pre-installed at the manufacturing facility.
IconMaster LITE systems do not include the MGI-3903 IconLogo graphics module.
Changing MKE-3901 Front Module Jumpers Setting
Note: There are no jumpers on the MKA-3901 discrete audio module.
The MKE-3901 front module includes these jumpers. (
Table 2-2
on page 23 shows the different jumpers and their settings. Jumpers are preset to default values at the manufacturing facility. Default values are indicated in
Table 2-2
.)
J16: Reference input termination (see
Figure 2-20
for the location)
J17 and J18: Serial E and Serial A port standards (see
Figure 2-21
for the location)
J20 and J22: AES Audio-Over 1 and 2 (see
Figure 2-20
for the location)
J25 and J26: Serial Port A (RS-232-A) format (see
Figure 2-22
for the location)
IconMaster
Installation and Configuration Manual
21
To change the jumper settings, follow these steps:
1
Remove the MKE-3901 module from the NEO frame. (For instructions, see the NEO
FR-3901, FR-3903, and FR-3923 Mounting Frames Installation and Operation Manual).
2
Using a pair of tweezers or needle-nosed pliers, pull the jumper pack loose from its location.
3
Push the jumper pack onto the pins of the desired location.
4
Reinstall the MKE-3901 front module into the NEO frame.
Jumper J16
Jumper J22
Jumper J20
Figure 2-20 Jumpers for Reference Input and AES Audio-Over
Jumper J17 Jumper J18
Figure 2-21 Jumpers for Serial Port Standard
1
1
Jumper J17 on MKE-3901 must be set to same standard as jumper pack A2. Jumper J18 on MKE-3901 must be set to same standard as jumper pack A1. For more information see
Figure 2-34
on page 37 and
Table 2-9
on page 39.
22
Chapter 2
Installation
Jumper J25
Jumper 26
Figure 2-22 Jumpers for Serial Port A Format
Note: Jumpers J20 and J22 on the MKE-3901 must be set to Balanced when the video breakout module is used.
Jumper J17 on the MKE-3901 must be set to the same standard as jumper pack A2. For more information see
Figure 2-34
on page 37 and
Table 2-9
on page 39.
Jumper J18 on the MKE-3901 must be set to the same standard as jumper pack A1. For more information see
Figure 2-34
on page 37 and
Table 2-9
on page 39.
IconMaster
Installation and Configuration Manual
23
Table 2-2 Jumper Settings
Function
Reference input termination
Settings
Jumper 16
75
impedance*
Serial port standard
Jumper 17/ Port E
Ext. Routing Control
Serial RS-232*
Hi-Z impedance
Jumper 18/Port B
Automation
Serial RS-232
Serial RS-422 Serial RS-422*
Audio-over impedance
Jumper 22
AES A/O 1 balanced*
Jumper 20
AES A/O 2 balanced*
AES A/O 1 unbalanced
AES A/O 2 unbalanced
Serial port A
(RS-232 format)
Must always be set to 232
Jumper 25
232
* Default value
Jumper 26
232
24
Chapter 2
Installation
Installing Optional NEO Modules (MKE-3901-FX and MKA-3901)
In addition to the standard NEO modules that come with your IconMaster system, you may purchase an MKE-3901-FX effects submodule and/or an MKA-3901 balanced audio module.
Note: When purchased as a package, the MKE-3901 and the MKA-3901 are attached together using standoffs and screws.
If you ordered these optional modules at the same time as your IconMaster, the modules will be installed in the NEO frame at the manufacturing facility, and no further NEO module installation procedures are necessary. If you ordered these optional modules separately, you can install them yourself. For module installation instructions, see the NEO FR-3901,
FR-3903, and FR-3923 Mounting Frames Installation and Operation Manual.
On one side, in this order:
MKA-3901
MKE-3901
MGI-3903
Figure 2-23 MKA-3901, MKE-3901, and MGI-3903 Module Order
To function correctly, MKA-3901, MKE-3901, and MGI-3903 modules must be connected to one another before installation, and the modules must be mounted in a specific order in a NEO frame.
Figure 2-23
on page 24 shows the alignment of the modules;
on page 25 shows an exploded view. The MKA-3901 and MKE-3901-FX are attached to the
MKE-3901 module.
Top – MKA-3901 front module
1
Middle – MKE-3901 front module
2 with optional MKE-3901-FX submodule
3
Bottom – MGI-3903
1
MKA-3901 modules do not require specific jumper settings.
2
MKE-3901 modules require specific jumper settings. See page 20 for more information.
3
MKE-3901-FX modules may be ordered and installed separately. See page 26 for more information.
.
IconMaster
Installation and Configuration Manual
25
Figure 2-24 Exploded View: MKA-3901 Front Module (Top) and MKE-3901 Front Module with Optional MKE-3901-FX Submodule (Middle), and MGI-3903 (Bottom)
Installing the Optional MKA-3901 Submodule
The MKA-3901 submodule can be ordered separately. (If you ordered this optional module at the same time as your IconMaster, it will be installed in the NEO frame at the manufacturing facility, and no further NEO module installation procedures are necessary.) If you have ordered the module separately and need to install it in your IconMaster system, follow these steps:
26
Chapter 2
Installation
1
Remove the MKE-3901 module from the NEO frame.
2
Fit the MKA-3901 module to the MKE-3901 module.
3
Secure using standoffs and retaining screws.
4
Reinstall the MKE-3901/MKA-3901 into the NEO frame, and then close the front panel.
Installing the Optional MKE-3901-FX Submodule
The MKE-3901-FX submodule can be ordered separately and added to an existing
MKE-3901 module. (If you ordered this optional module at the same time as your
IconMaster, it will be installed in the NEO frame at the manufacturing facility, and no further NEO module installation procedures are necessary.) If you have ordered the module separately and need to install it in your IconMaster system, follow these steps:
1
Remove the MKE-3901 module from the NEO frame.
2
If your system includes an MKA-3901 module, remove the four retaining screws from the
MKA-3901 module, and then separate the MKA-3901 module from the MKE-3901.
Retain the screws.
3
Locate and fit the MKE-3901-FX module into the correct position on the MKE-3901 module.
4
Install the submodule with the retaining screws included.
5
If applicable, fit the MKA-3901 module to the MKE-3901 module again.
6
Secure using standoffs and retaining screws.
7
Reinstall the MKE-3901 into the NEO frame, and then close the front panel.
Installing the NEO Frame into a Rack
For instructions about installing a NEO frame into a rack, see the FR-3901, FR-3903, and
FR-3923 Mounting Frames Installation and Operation Manual.
Your installation may also require breakout panel connections. See page 32 for more
information.
IconMaster
Installation and Configuration Manual
27
Connecting NEO Components
MKE-3901 Back Module Connections
shows the back module of the MKE-3901 module. Make all appropriate I/O connections as appropriate for your system setup. Specific information concerning
Ethernet, Genlock, Bus A and B, and multifunction I/O connectors is provided below.
Figure 2-25 MKE-3901 Back Module
Ethernet
Use Ethernet 1 to connect the MKE-3901 to a network hub or directly to an IconMaster control panel.
Use Ethernet 2 to connect the MGI-3903 to a network hub or directly to an IconLogo control panel.
Genlock
The default Genlock Source Type is Composite. To change this setting, see the Genlock dialog box in the IconMaster configuration utility software.
This input is terminated to 75
internally by default. See jumper J16 on page 23 if termination is not desired.
Multifunction I/O
The pin numbers for the Multi Function I/O connector, with corresponding pinout information, are shown in
Table 2-3
on page 28.
Bus A/Bus B Input Connectors
For information about Bus A and Bus B connectors, see
System Configurations—Platinum Routers
28
Chapter 2
Installation
Table 2-3 MKE-3901 Multi-Function I/O Pinouts
This pinout information is for use when it is necessary to wire directly to the connector. If you are using a
ICONM-BO-V breakout module (shown in
Figure 2-27
on page 32), this information is not required.
6
7
4
5
2
3
Pin Function
1 MKE AES A/O 2 (B+)*
Ground
GPI 11
GPI 14
GPI 17
GPI 18
GPO 6
8
9
GPO 4
GPO 2
10 Bypass relay control
11 GPI 8
12 GPI 4
13 GPI 7
14 RS-232-B RxD or
RS-422-B RX -
15 RS-232-B n/c or
RS-422-B RX +
Pin
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Function
MKE AES A/O 1 (B-)*
MKE AES A/O 2 (B-)*
Ground
GPI 12
GPI 13
GPI 16
GPO 11
GPO 7
GPO 5
GPO 3
GPO 1
GPI 6
GPI 2
GPI 5
GPI 3
54
55
56
50
51
52
53
46
47
48
49
Pin Function
43 MKE AES A/O 1 (B+)*
44
45
Ground
GPI 9
57
GPI 10
GPI 15
GPO 8
GPO 9
GPO 10
GPO 12
GPO 13
MGI LTC +
MGI LTC -
MGI temperature sensor +
MGI temperature sensor -
RS-232-D RxD
16 RS-232-E TxD or
RS-422-E TX -
17 RS-232-E n/c or
RS-422-E TX +
18 RS-232-E n/c or
RS-422-E RX +
19 RS-232-E RxD or
RS-422-E RX -
37
38
39
40
GPI 1
Ground
+5V**
Ground
58
59
60
61
RS-232-D TxD
RS-422-C TX -
RS-422-C TX +
RS-422-C RX +
20 RS-232-B TxD or
RS-422-B TX -
21 RS-232-A RxD
41
42
RS-232-B n/c or
RS-422-B TX +
RS-232-A TxD
62 RS-422-C RX -
*Audio Over 1 and 2: For balanced data, use B+ and B-. For unbalanced (coax), use B+ for the signal and connect
B- to ground (shield). There are also jumpers on the MKE card, which must be set to indicate balanced or coax.
**Reserved for bypass relay operation.
MKA-3901 Back Module Connections
shows the back module of the MKA-3901 module. Make all appropriate I/O connections as appropriate for your system setup.
IconMaster
Installation and Configuration Manual
29
The pin numbers for the AES Input connector, with corresponding pinout information, are shown in
The pin numbers for the AES Output connector, with corresponding pinout information, are shown in
Figure 2-26 MKA-3901 Back Module
Table 2-4 MKA-3901 AES Input Connector Pinouts
This information is for use when it is necessary to wire directly to the AES input connector. If you are using a
ICONM-BO-VAC or ICONM-BO-VAB breakout module, this information is not required.
6
7
4
5
2
3
Pin Function
1 Spare
Spare
Ground
Spare
Spare
Ground
AES BUS A 3 (B+)
8
9
AES BUS A 3 (B-)
Ground
10 AES BUS A 1 (B-)
11 AES BUS A 1 (B+)
12 Ground
13 AES BUS B 3 (B-)
14 AES BUS B 3 (B+)
15 Ground
16 AES BUS B 1 (B-)
17 AES BUS B 1 (B+)
18 Ground
Pin Function
22 Ground
23 N/C
24 Ground
25 Ground
26 Ground
27 Ground
28 Ground
29 Ground
30 Ground
31 Ground
32 Ground
33 Ground
34 Ground
35 Ground
36 Ground
37 Ground
38 Ground
39 Ground
Pin Function
43 AES BUS A 4 (B-)
44 AES BUS A 4 (B+)
45 Ground
46 AES BUS A 2 (B-)
47 AES BUS A 2 (B+)
48 Ground
49 AES BUS B 4 (B-)
50 AES BUS B 4 (B+)
51 Ground
52 AES BUS B 2 (B-)
53 AES BUS B 2 (B+)
54 Ground
55 Reserved for future use
56 Reserved for future use
57 Ground
58 Reserved for future use
59 Reserved for future use
60 Ground
30
Chapter 2
Installation
Table 2-4 MKA-3901 AES Input Connector Pinouts (Continued)
This information is for use when it is necessary to wire directly to the AES input connector. If you are using a
ICONM-BO-VAC or ICONM-BO-VAB breakout module, this information is not required.
Pin Function
19 Reserved for future use
20 Reserved for future use
Pin Function
40 Ground
41 Ground
Pin Function
61 Reserved for future use
62 Reserved for future use
21 Ground 42 Ground
For balanced data, use B+ and B-. For unbalanced (coax), use B+ for the signal and connect B- to ground (shield).
To use the coax, the C version of the card must be purchased.
Table 2-5 MKA-3901 AES Output Connector Pinouts
This information is for use when it is necessary to wire directly to the AES output connector. If you are using the
ICONM-BO-VAC or ICONM-BO-VAB breakout module, this information is not required.
6
7
4
5
2
3
Pin Function
1 Reserved for future use
Reserved for future use
Ground
AES Pgm 3 (B+)
AES Pgm 3 (B-)
Ground
AES Pst 1 (B+)
8
9
AES Pst 1 (B-)
Ground
10 AES Pst 3 (B+)
11 AES Pst 3 (B-)
12 Ground
Pin Function
22 Ground
23 N/C
24 Ground
25 Ground
26 AES Pgm 4 (B+)
27 AES Pgm 4 (B-)
28 Ground
29 AES Pgm 1 (B+)
30 AES Pgm 1 (B-)
31 Ground
32 AES Clean 2 (B+)
33 AES Clean 2 (B-)
Pin Function
43 Reserved for future use
44 Reserved for future use
45 Ground
46 AES Pgm 2 (B+)
47 AES Pgm 2 (B-)
48 Ground
49 AES Pst 2 (B+)
50 AES Pst 2 (B-)
51 Ground
52 AES Pst 4 (B+)
53 AES Pst 4 (B-)
54 Ground
IconMaster
Installation and Configuration Manual
31
Table 2-5 MKA-3901 AES Output Connector Pinouts (Continued)
This information is for use when it is necessary to wire directly to the AES output connector. If you are using the
ICONM-BO-VAC or ICONM-BO-VAB breakout module, this information is not required.
Pin Function
1 Reserved for future use
13 AES Clean 1 (B+)
14 AES Clean 1 (B-)
15 Ground
16 AES Mon 1 (B+)
Pin Function
22 Ground
34 Ground
35 AES Clean 3 (B+)
36 AES Clean 3 (B-)
37 Ground
Pin Function
43 Reserved for future use
55 AES Clean 4 (B+)
56 AES Clean 4 (B-)
57 Ground
58 AES Mon 2 (B+)
17 AES Mon 1 (B-)
18 Ground
19 AES Mon 3 (B+)
20 AES Mon 3 (B-)
38
39
40
41
Ground
Ground
Ground
Ground
59
60
61
62
AES Mon 2 (B-)
Ground
AES Mon 4 (B+)
AES Mon 4 (B-)
21 Ground 42 Ground
For balanced data, use B+ and B-. For unbalanced (coax), use B+ for the signal and connect B- to ground (shield).
To use the coax, the C version of the card must be purchased.
32
Chapter 2
Installation
Installing Breakout Modules
There are three breakout modules available in the IconMaster system.
Table 2-6
shows the functionality of each of the breakout modules.
Table 2-6 Breakout Module Packages
Breakout Back Module
Name
ICONM-BO-V video breakout module (see
ICONM-BO-VAB balanced audio breakout module
Video Module
RS-232 and RS-422;
BNCs for audio over and video relay bypass
RS-232 and RS-422;
BNCs for audio over and video relay bypass
Audio Module
Not applicable
Screw terminals for discrete audio in and out
ICONM-BO-VAC coaxial audio breakout module (see
RS-232 and RS-422;
BNCs for audio over and video relay bypass
BNC connections for discrete audio in and out
Connecting Cables
MKE breakout cable
(165-000242-00)
MKA breakout cable
(165-000243-00) x2
MKE breakout cable
(165-000242-00)
MKA breakout cable
(165-000243-00) x2
MKE breakout cable
(165-000242-00)
ICONM-BO-V Video Breakout Module
Term.
1
2
7
8
9
3
4
5
6
10
P2 P3 P4 P5 P6
Figure 2-27 ICONM-BO-V Breakout Module
IconMaster
Installation and Configuration Manual
33
The ICONM-BO-V (
Figure 2-27
) is the breakout module for the MKE-3901 video module.
The module converts the 62-pin Multi Function I/O connector of the MKE-3901 to separate screw, BNC, and DB-9 connectors.
Figure 2-28
on page 34 shows how the GPIs and GPOs (GPI outputs) are connected.
For information on the jumpers and jumper packs used on the ICONM-BO-V module, see
Screw Connectors
Figure 2-27
shows the screw-type connectors on the ICONM-BO-V breakout module. Each row of screw terminals (P2 to P6) is described in
Table 2-7
.
Table 2-7 ICONM-BO-V Screw Terminals
6
7
4
5
8
9
2
3
Terminal P2
1 GPI 8
GPI 7
GPI 6
GPI 5
GPI 4
GPI 3
GPI 2
GPI 1
GPO 7
10 GND
P3
MKE A/O 1 +
MKE A/O 1 -
GND
MKE A/O 2 +
MKE A/O 2 -
GPO 3
GPO 2
GPO 9
GPO 10
MGI TEMP SENS + GPO 1
MGI TEMP SENS Bypass relay control
GPO 11
GPO 12
MGI LTC +
MGI LTC-
GND
P4
GPO 6
GPO 5
GPO 4
+5 to MKE Relay
+5 to MKA
Breakout
+5 from MKE
P5
GPI 17
GPI 18
GPO 8
GPO 13
-VE to MKE CTRL
-VE to MKA CTRL
P6
GPI 9
GPI 10
GPI 11
GPI 12
GPI 13
GPI 14
GPI 15
GPI 16
GND
GND
Bypass Relay Control
Connect P4, Pins 8, 9, and 10 together. This supplies the +5V from the MKE-3901 module to the emergency relays on the video breakout module and the audio breakout modules.
Connect P5, Pins 9 and 10 to P4, Pin 7.
To externally control the bypass relays, disconnect P4, pin 7 from P5 pin 9 and P5 pin
10.
To set bypass relays to BYPASS mode (emergency inputs routed to PGM outputs), leave
P5 pin 9 and P5 pin 10 open (no connections).
To set bypass relays to OPERATE mode (IconMaster PGM to PGM outputs), connect P5 pin 9 and P5 pin 10 to GND (P6 pin 9 or P6 pin 10).
34
Chapter 2
Installation
GPI/GPO Connections
Figure 2-28 GPI and GPO (GPI Out) Connections
BNC Connectors
Figure 2-29 ICONM-BO-V BNC Connectors
Jumpers for AES Audio Over Impedance
The ICONM-BO-V video breakout module includes four jumpers (J1, J2, J3, and J4), which are used to set the impedance of AES Audio-Over 1 and Audio-Over 2. The orientation of the jumper pins in
matches the way you view them as you read the “J” labelling on the board.
IconMaster
Installation and Configuration Manual
35
Jumpers J1, J4, J2, and J3
Figure 2-30 Jumpers on ICONM-BO-V (for BNC Connectors)
To set the individual jumpers, follow these steps:
1
Move jumpers J1 and J4 to set the A/O 1 (top BNC connector) to either Unbalanced or
Balanced (see
Figure 2-31
).
Figure 2-31 A/O 1 Jumpers
2
Move Jumpers J2 and J3 to set A/O 2 (bottom BNC connector) to either Unbalanced or
Balanced (see
Figure 2-32
).
36
Chapter 2
Installation
Figure 2-32 A/O 2 Jumpers
Bypass Relay Jumper (HD or Multiformat Operation)
For HD or multi-format operation, jumper J10 should be left in the default position, connecting pins 1 to 2. When a system is configured for SD, jumper J10 should connect pins 2 to 3. See
Figure 2-33
on page 36 for relay bypass jumper location and settings.
Figure 2-33 Relay Bypass Jumper J10
DB-9 Connectors
Note: Jumpers J20 and J22 on the MKE-3901 must be set to Balanced when the video breakout module is used.
Jumper J17 on the MKE-3901 must be set to the same standard as jumper pack A2. For more information see
Figure 2-34
on page 37 and
Table 2-9
on page 39.
Jumper J18 on the MKE-3901 must be set to the same standard as jumper pack A1. For more information see
Figure 2-34
on page 37 and
Table 2-9
on page 39
IconMaster
Installation and Configuration Manual
37
Table 2-8
on page 38 describes the pinouts for the DB-9 connectors, and
Table 2-9
on page 39 describes the use of the DB-9 serial connectors.
The ICONM-BO-V video breakout module includes two jumper packs (A1 and A2), which are used for setting the serial port standard (RS-232 or RS-422). The orientation of the jumper pins in
Figure 2-31
and
Figure 2-32
matches the way you view them as you read the “J” labelling on the board.
To set the jumper packs, follow these steps:
1
Locate jumper packs A1 and A2 on the ICONM-BO-V module, as shown in
Figure 2-34
.
Figure 2-34
shows both serial ports in RS-422.
2
If necessary, extract the jumper packs, and then rotate them to match the RS-232 or RS-422 setting as required.
shows RS-232 and RS-422 orientation.
Jumper packs A1 and A2
Jumper J18 on MKE-3901 must be set to same standard as jumper pack
A1 for serial port B.
Jumper J17 on MKE-3901 must be set to same standard as jumper pack
A2 for serial port E.
The settings shown at right are for RS-422 configuration.
The orientation of the jumpers should be reversed for RS-232, as below.
Figure 2-34 Jumper Packs on ICONM-BO-V (in RS-422 Mode)
Note: Each serial connector (RS-232 and RS-422) has the following settings:
• 38400 baud rate
• 8 data bits
• No parity
• 1 stop bit
• No flow control
38
Chapter 2
Installation
DB-9 (RS-232 and RS-422) Connectors
Table 2-8 ICONM-BO-V DB-9 Pinouts
1
2
5
6
Breakout
DB9 Pin
3
4
7
Port A
RS232
TxD
RxD
GND
Port B, Port E
RS232 / RS422 Selectable
RS-232 Connection
Frame Ground
RS-422
Connection
Frame Ground
RxD (Data received by
IconMaster)
TxD (Data sent by
IconMaster)
Ta Tx- (Data sent by
IconMaster)
Rb Rx+ (Data received by
IconMaster)
DTR (Data Terminal
Ready) *
Ground
Rc (Receiver Common or
Shield)
Ground
DSR (Data Serial Ready)
*
Tc (Transmit Common or
Shield)
RTS (Request to Send) ** Tb Tx+ (Data sent by
IconMaster)
8 CTS (Clear to Send) ** Ra Rx- (Data received by
IconMaster)
Frame Ground Frame Ground 9
* DB9 Pins 4 (DTR) and 6 (DSR) are connected internally to GND.
** DB9 Pins 7 (RTS) and 8 (CTS) are not used by IconMaster.
Port C
RS422
Frame Ground
Ta Tx-
Rb Rx+
Tb Tx+
Ra Rx-
Frame Ground
Port D
RS232
RxD
TxD
GND
Note: RS-232 pinouts of port A are opposite to those of ports B, D, and E. The use of straight-through versus null-modem cables must be carefully considered.
IconMaster
Installation and Configuration Manual
39
Table 2-9
shows default settings for the DB-9 connectors. These connector assignments can be changed via the ICU Serial Port Configuration dialog box. For more information, see .
Table 2-9 DB-9 (RS-232 and RS-422) Connector Usage
Connector
RS-232-A
RS-232/422-B
RS-232/422-C
RS-232-D
RS-232/422-E
Use
MKE-3901 machine control
MKE-3901 automation, router, multiviewer, or machine control
Reserved
MGI-3903 EAS
MKE-3901 automation, router, multiviewer, or machine control
Baud Rate
38400
38400
38400
9600
38400
Notes
See page 107 for more machine control
information
Jumper J18 on the MKE-3901 must be set to the required standard and jumper pack A1 on the breakout module must be set to the same
standard as J18 (see page 20 for more jumper
information)
See page 121 and page 162 for more
automation control information
Reserved for future use
Connect the EAS receiver for emergency notification messages
Jumper J17 on the MKE-3901 must be set to the required standard and jumper pack A2 on the breakout module must be set to the same
standard as J17 (see page 20 for more jumper
information)
Common DB-9 Cable Arrangements Examples
Figure 2-35 RS-232 IconMaster Port E to Integrator or Panacea Pin Connections
40
Chapter 2
Installation
Figure 2-36 RS-422 IconMaster Port E to Integrator, Panacea, or Platinum Pin Connections
Figure 2-37 RS-422 IconMaster Port B/E to Common PC Serial Port Pin Connections
Note: If re-assigned to port A, use a straight-through connection instead of this null-modem connection.
Figure 2-38 RS-232 IconMaster Port A to SPT Pin Connections
Note: If re-assigned to port B or port E, use a null-modem connection instead of this straight-through connection.
IconMaster
Installation and Configuration Manual
41
ICONM-BO-VAB Balanced Audio Module
The ICONM-BO-VAB is a breakout module for the MKA-3901-B audio module. It also includes the video functionality of the ICONM-BO-V module. The audio portion of the module converts the 62-pin AES Input and AES output connectors of the MKA-3901-B to screw terminal connections.
shows the screw-type connectors on the audio breakout module. Each row of screw terminals (P4 to P15) is described in
.
Term.
1
4
5
2
3
6
7
8
P4 P5
P6
P7 Term.
1
6
7
8
4
5
2
3
P8 P9 P10 P11 Term.
P12 P13 P14 P15
1
2
3
4
5
6
7
8
Figure 2-39 ICONM-BO-VAB Breakout Module
7
8
5
6
3
4
1
2
3
4
1
2
5
6
Table 2-10 ICONM-BO-VAB Breakout Module Screw Terminals
Terminal
No.
Terminal Type/Function
P4 Inputs
BUS B1 +
BUS B1 -
BUS B1 GND
BUS B3 +
BUS B3 -
BUS B3 GND
NC
NC
P8 Outputs
MON 2 +
MON 2 -
MON 2 GND
MON 3 +
MON 3 -
MON 3/4 GND
P5 Inputs
BUS A4 +
BUS A4 -
BUS A4 GND
BUS B2 +
BUS B2 -
BUS B4/B2 GND
BUS B4 +
BUS B4 -
P6 Inputs
BUS A1 +
BUS A1 -
BUS A1 GND
BUS A2 +
BUS A2 -
BUS A2/A3 GND
BUS A3 +
BUS A3 -
P9 Outputs
CLEAN 3 +
CLEAN 3 -
CLEAN 3 GND
P10 Outputs
PST 4 +
PST 4 -
PST 4 GND
CLEAN 4 +
CLEAN 4 -
CLEAN 1 +
CLEAN 1 -
CLEAN 4/MON 1 GND CLEAN 1/2 GND
P7 Inputs
SPARE 1 +
SPARE 1 -
SPARE 1 GND
SPARE 2 +
SPARE 2 -
SPARE 2 GND
NC
NC
P11 Outputs
PST 1 +
PST 1 -
PST 1 GND
PST 2 +
PST 2 -
PST 2/3 GND
42
Chapter 2
Installation
7
8
5
6
3
4
1
2
Table 2-10 ICONM-BO-VAB Breakout Module Screw Terminals (Continued)
7
8
Terminal
No.
Terminal Type/Function
MON 4 +
MON 4 -
MON 1 +
MON 1 -
CLEAN 2 +
CLEAN 2 -
P12 Inputs
NC
NC
EMER PGM 1 +
EMER PGM 1 -
EMER PGM GND
EMER PGM 2+
EMER PGM 2-
EMER PGM 2 GND
P13 Outputs
PGM 1 +
PGM 1 GND
PGM 1 -
PGM 2+
PGM 2 GND
PGM 2 -
NC
NC
P14 Outputs
PGM 3 +
PGM 3 GND
PGM 3 -
PGM 4 +
PGM 4 GND
PGM 4 -
NC
NC
PST 3 +
PST 3 -
P15 Inputs
NC
NC
EMER PGM 3 +
EMER PGM 3 -
EMER PGM 3 GND
EMER PGM 4 +
EMER PGM 4 -
EMER PGM 4 GND
ICONM-BO-VAC Coaxial Audio Module
The ICONM-BO-VAC is a breakout module for the MKA-3901-B audio module. It includes an ICONM-BO-V module with an audio portion. The audio portion of the module converts the 62-pin AES input and AES output connectors of the MKA-3901-B to coaxial connections. Each connector is labelled in
.
IconMaster
Installation and Configuration Manual
43
on page 43 shows the four BNC connectors on the audio breakout module for
connecting emergency inputs. From left to right, the connectors are for AES4 to AES 1.
Figure 2-40 ICONM-BO-VAC Breakout Module
Figure 2-41 Coaxial Connector Labels
Figure 2-42 Emergency BNC Audio Inputs (AES4 to AES 1, From Left to Right)
Video Relay Bypass Module
The video relay bypass is a separate module that is connected to the video breakout module.
44
Chapter 2
Installation
Connections with ICONM-BO-V Module
When using the ICONM-BO-V module, connect PGM Output on the MKE-3901-BM to
PGM IN on the video relay bypass module using a coax cable, as shown in
Figure 2-43 MKE-3901 Connections to the Video Relay Bypass Using the ICONM-BO-V
Connections with ICONM-BO-VAB or ICONM-BO-VAC Module
When using the ICONM-BO-VAB or ICONM-BO-VAC module, connect PGM Output on the
MKE-3901-BM to the PGM IN on the Video Bypass module using the provided coax cable, as shown in
Figure 2-44
.
Figure 2-44 MKE-3901 Connections to the Video Relay Bypass Using the ICONM-BO-VAB
IconMaster
Installation and Configuration Manual
45
Connecting Optional GPI Input and Output Devices
IconMaster frames are designed to work with JLCooper Electronics eBOX Quad Serial to
Ethernet Interface. The eBOX is a general purpose interface box that converts serial communication ports, GPI inputs, and GPI outputs and outputs to 10/100BaseT Ethernet.
Using eBOX, you can control up to 66 GPI input and 61 GPI output devices. IconMaster communicates with eBOX through the IconMaster Ethernet connection.
Connecting the eBOX to the IconMaster
1
Connect an Ethernet crossover cable between the Ethernet connector on a PC to the
Ethernet connector on the eBOX. (If the PC is connected to a network, remove it from the network before connecting it to the eBOX.)
2
Set the eBOX DIP switch 8 to ON (to allow you to access the JLCooper web interface).
3
Access Network Connections from the Windows Control Panel box (Start > Control
Panel > Network Connections).
4
Select Local Area Network. The Local Area Network Connections box will appear.
5
Select TCP/IP as the Internet procotol. The Internet Protocol (TCP/IP) Properties box will appear. Use the following IP addresses:
IP address: 192.168.254.100
Subnet mask: 255.255.255.0
Default gateway: IP address: 192.168.254.102
6
Using Microsoft Internet Explorer 6 as your web browser, access the JLCooper electronics eBOX configuration web page, and then configure the eBOX to Server mode, as described in the eBOX Ethernet to Serial & GPI Interface Users Manual.See
and
on page 47 for settings information.
Note: Internet Explorer 6 is the only web browser that can be used to configure and program the eBOX.
Table 2-11 eBOX to IconMaster Configuration Settings
Configuration Item
Primary Setup Information
Device IP Address
Subnet Mask
Gateway Address
Port number
Setting
Site-specific
Site-specific
Site-specific
5003
Client Mode Ony Information - Not Used
Password Protection - Not Used
Serial Port Setup Parameters
Baud Rate (Serial 1-4) 38400
Parity (Serial 1-4)
Parity Type (serial 1-4)
Serial Time Out
Maximum Buffer Size
On
Even
Per default
Per default
46
Chapter 2
Installation
7
Turn DIP switch 8 to OFF, and then unplug the Ethernet connection between the PC and the eBOX. If necessary, reconnect the reconnect the PC to its network.
8
Move the eBOX to its final destination, and then connect the eBOX to the Ethernet network.
9
Make all other desired GPI/GPO and serial connections to the eBOX connections.
Note: The eBOX needs to be properly grounded to ensure proper operation of the GPI and
GPO.
10
Set the buttons on the back of the eBOX to the correct RS-232 or RS-422 position, and set
Host mode or Machine mode (this sets the states of pins 2 and 3 for TX and RX).
Note: DIP switches 1, 2, and 3 must be set to ON and DIP switch 7 must be set to OFF for the eBOX to run in the web page-defined IP address mode.
11
Using the IconMaster Configuration Utility (ICU), configure the eBOX settings as applicable, in this order:
Enable External I/O Module (page 176)
External Interface connections (page 176)
Machine control, GPI/GPO (page 162, page 165, page 167)
Serial tally to tally system (page 178)
IconMaster
Installation and Configuration Manual
47
Figure 2-45 JLCooper EBox Settings for IconMaster
Customizing Pushbuttons
The IconMaster control panel uses pushbuttons that you can customize. To customize a
pushbutton, follow these steps:
48
Chapter 2
Installation
1
Remove the lens assembly by grasping the switch tightly and pulling the lens off the switch.
Once the lens assembly is released from the switch, the lens and pushbutton can be separated.
2
Remove the appropriate text film from the “Optional Control Panel Labels” plastic sheet included in this manual.
3
Separate the lens and the pushbutton and then place the text film inside the lens cap.
4
After aligning the notches in the lens with the tabs in the pushbutton, join the pieces together.
5
Firmly press the lens assembly onto the plunger by applying pressure from the top to the bottom until both are snapped together.
Figure 2-46 Removable Parts of a Pushbutton
Installing an Optional Fader Bar
When installed as an upgrade, the IconMaster fader bar must be inserted and mounted from underneath the main control panel after the existing front plastic bezel is removed.
There are three general stages to the installation: removing the bezel, installing the fader bar assembly, and assembling the handle.
Disassembling the IconMaster
1
Disconnect the power supply.
2
Disconnect the Ethernet and serial connections from the IconMaster control panel as necessary.
3
If necessary, remove the IconMaster control panel from its desktop/tabletop location from its mounting rack.
IconMaster
Installation and Configuration Manual
49
Removing the Bezel
1
Turn the main control panel over on its face.
2
In the connector bay on the left side, remove the four screws that hold the fader bar access cover in place (see
Figure 2-47
).
Remove the four screws holding the access cover in place.
Figure 2-47 Removal of Access Cover
3
Inside the panel (as shown in
Figure 2-48
on page 50), remove the two screws that secure the existing plastic bezel, retaining the screws for future use.
4
Turn the panel over, and then lift off the existing plastic bezel.
Installing the Fader Bar Assembly
1
On the front of the panel, position the new fader bar bezel over the fader bar slot, ensuring that you align the two square holes with the up and down arrow LEDs.
2
Turn the panel back over to reveal its underside, and then, using the original bezel screws, secure the new fader bar bezel (see
Figure 2-48
).
CAUTION: Do not overtighten the fader bar mounting screws. A snug fit is sufficient.
50
Chapter 2
Installation
Bezel screws
Standoffs for mounting fader bar assembly
Plastic power supply connector
Figure 2-48 Securing the New Bezel
3
Slide the fader bar arm through the slot, so that the assembly fits over the two standoffs
(see
Figure 2-49
).
4
Mount the fader bar assembly onto the standoffs using the two provided screws.
Ensure the connector cable side of the fader bar assembly is facing the shallow end of the control panel (nearest to the plastic power supply connector).
5
Remove the jumper located on the header next to the fader bar assembly.
6
Attach the fader cable to the header connector.
7
Reinstall the access cover, being careful to avoid pinching the cable.
CAUTION: The locking cable connector will only fit one way. Do not force the connector if it does not snap into place easily.
IconMaster
Installation and Configuration Manual
51
Front of main control panel
Plastic power supply connectors
Wires facing front of main control panel
Jumper removed;
3-pin connector attached
Fader bar assembly installed
Rear of main control panel
(next to Audio Control Panel)
Figure 2-49 Fader Bar Installation and Connection
Assembling the Handle
1
Turn the control panel right side up.
2
Align the two opposing caps of the handle on the fader bar arm, and then insert the provided screw and nut.
3
Tighten the screw, and then snap on the two end caps.
4
Reinstall the IconMaster control panel into its desktop/tabletop or mounting rack location.
5
Reconnect any Ethernet and/or serial connectors.
6
Reconnect the power supply.
52
Chapter 2
Installation
3
Module Configuration
Overview
This chapter describes the configuration and use of the MKE-3901, MKA-3901, and
MGI-3903 modules in the IconMaster system.
The following topics are covered:
Operator, All, and Setup Parameter Lists
This chapter presupposes that you have a working knowledge of NEO card-edge configuration and have used it with other NEO modules. If not, please refer to the NEO
FR-3901, FR-3903, and FR-3923 Mounting Frames Installation and Operation Manual and familiarize yourself with card-edge operation before you continue the configuration process.
Navigating the MKE-3901 Operator and All Lists
To navigate, and then view or change a parameter from the Operator and All Lists, follow these steps:
1
Open the front panel of the NEO frame.
2
Press any card-edge control to turn on the VFD screen.
The message MKE3901 appears. If a previous user has left the display at a different parameter name, repeatedly press the Escape button until the message MKE3901 appears.
After several seconds of inactivity, a scrolling message will appear, describing the purpose of the currently selected parameter.
3
Push the Enter button.
The name of the first parameter option in the list appears.
4
Push the Enter button again to access the options for the parameter displayed on the VFD screen.
OR
Press the Nav+/Nav- switch down repeatedly to view other parameters, and then press
Enter to access an item’s parameter options.
5
Press the Nav+/Nav- switch up or down to scroll through the different selectable parameter options, and then press Enter to select the value you want.
53
54
Chapter 3
Module Configuration
OR
Press the Nav+/Nav- switch up or down to adjust the numeric parameter value, and then press Enter.
6
Close the front panel of the frame to ensure the cooling system continues to operate properly.
Operator, All, and Setup Parameter Lists
The MKE-3901 displays its parameters in an Operator List, All List, and Tree View. These parameters are visible at the card-edge of the module and in CCS software.
These lists include the following parameters:
Operator and
All Lists
Table 3-1 MKE-3901 Operator and All Lists
Card-Edge ID Parameter Name
Unit_Name Unit Name
SW_Version Software Version
IP_Address
SubnetMask
Gateway
OperStd
Lite_Mode
AutoHold
Items in gray are in the All List only.
IP address
Subnet Mask
Gateway
Operation Standard
Lite Mode
Automation Hold
Function
Displays the name of the device
Displays the version number of the currently installed software
Changes the address of the
IconMaster module on the network.
User Range
String (MKE3901)
String (none)
String (192.168.100.252)
Changing the IP address releases the IconMaster from panel control. To regain control of the panel, enter the new IP address into the panel's list of “reachable” machines
Changes the range of IP addresses that can communicate with this device
Changes the network routing for the device
String (255.255.0.0)
String (0.0.0.0)
String (None)
String (No) Indicates whether the device is operating as a lite version of
IconMaster; some features are disabled in this mode
Stops the IconMaster from responding to Automation commands
On
Off
IconMaster
Installation and Configuration Manual
55
Key1_OnNext
Key2_OnNext
Key3_OnNext
Key4_OnNext
Key5_OnNext
Key6_OnNext
Key1_OnAir
Key2_OnAir
Key3_OnAir
Key4_OnAir
Key5_OnAir
Key6_OnAir
Table 3-1 MKE-3901 Operator and All Lists (Continued)
Card-Edge ID Parameter Name
PgmBypass Program Bypass
PST_Src
PGM_Src
BKGD
TAKE
PREROLL
TransSpeed
TransShape
ATransShape
BreakawayMode
PST Source Selection
PGM Source Selection
BKGD
TAKE
PREROLL
Transition Speed
Transition Shape
Audio Trans Shape
Breakaway Mode
Function
When activated, bypasses the program bus
Selects the source for preset bus String (None)
Selects the source for the program bus
String (None)
Activates the BKGD function, so that a background transition from the PST bus to the PGM bus will occur when you select Take or
Preroll
On
Off
Triggers a take, causing the next transition to start immediately
Triggers a preroll, activating a different piece of equipment to perform an event
On
Off
On
Off
Sets the transition rate
Selects the type of transition that will be performed
Selects the type of audio transition that will be performed
When off, the audio and video transition at the same time; when this parameter is set to one of the other options, only that option will transition
Triggers the specified key on the next transition
User Range
On
Off
String (None)
Cut-Fade
Fade-Cut
Fade-Fade
X-Fade
Cut-Fade
Fade-Cut
Fade-Fade
X-Fade
Off
Video
Audio
On
Off
Key1 On Next Trans
Key2 On Next Trans
Key3 On Next Trans
Key4 On Next Trans
Key5 On Next Trans
Key6 On Next Trans
Key1 On Air
Key2 On Air
Key3 On Air
Key4 On Air
Key5 On Air
Key6 On Air
Triggers the specified key to air immediately
On
Off
56
Chapter 3
Module Configuration
Table 3-1 MKE-3901 Operator and All Lists (Continued)
Card-Edge ID
AO1_OnNext
AO2_OnNext
AO1_OnAir
AO2_OnAir
K3_LogoSel
K4_LogoSel
K5_LogoSel
K6_LogoSel
FTB
Parameter Name
AO1 On Next Trans
AO2 On Next Trans
AO1 On Air
AO2 On Air
Assign Logo to Key3
Assign Logo to Key4
Assign Logo to Key5
Assign Logo to Key6
Fade To Black
Function
Triggers the specified audio over on the next transition
Triggers the specified audio over to air immediately
Selects the logo for the specified key
Causes the video program outputs to immediately fade to black
SIL
S_PST_Present
S_PST_NonSync
S_PGM_Present
S_PGM_NonSync
S_K1_Present
S_K1_NonSync
S_K2_Present
S_K2_NonSync
S_REF_Present
S_HW_Error
S_COMM_Error
S_Warning_Msg
BreakawayStatus
Silence
PST Present Status
PST NonSync Status
PGM Present Status
PGM NonSync Status
Key1 Present Status
Key1 NonSync Status
Key2 Present Status
Key2 NonSync Status
Reference Present
Hardware Error
Communication Error
System Warning Msg
Breakaway Status
User Range
On
Off
On
Off
String (None)
Causes the audio program outputs to immediately fade to silence
Indicates whether there is data on the Preset bus
Indicates whether the Preset bus is synced correctly
Indicates whether there is data on the Program bus
Indicates whether the Program bus is synced correctly
Indicates whether the specified key has been assigned
Indicates whether the specified key is synced correctly
Indicates whether the specified key has been assigned
Indicates whether the specified key is synced correctly
Indicates whether reference signal is present
Indicates a detected hardware malfunction
Indicates a detected communication error
Indicates that the system has triggered a warning message
Displays whether breakaway status is active
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
On
Off
On
Off
Yes
No
Yes
No
IconMaster
Installation and Configuration Manual
57
Setup
Parameters
You can modify the SETUP parameters to configure the card-edge controls for your personal needs. The structure of the Setup menu is as follows (default settings are indicated by asterisks):
Nav Mode (Navigation Mode)
(Options: Oper List*, All List, Tree View)
SelPar Adj Mode (Selectable Parameter Adjust Mode)
(Options: Immediate, Delayed*)
Brws Mode (Browse Mode)
(Options: Param List, Param+Val*)
Scrl Mode (Scroll Mode)
(Options: Wrap*, Don’t Wrap)
Disp Inten (Display Intensity)
(Options: 100%, 50%*, 25%, 12%)
Param Desc (Parameter Description)
(Options: Disabled, Enabled*)
About [RO]
See your NEO FR-3901, FR-3903, and FR-3923 Mounting Frames Installation and Operation
Manual for more information on Setup items.
LEDs and Module Indicators
MKE-3901 LEDs and Module Indicators
Each MKE-3901 module has 8 card-edge LEDs and 4 module indicators. The module indicators include Major Alarm and Minor Alarm. These alarms are not currently in use in the IconMaster system.
58
Chapter 3
Module Configuration
Figure 3-1
illustrates the locations of the LEDs and standard module indicators on the
MKE-3901 module. The meanings of the LEDs are described in
Table 3-2
. The meanings of the module indicators are described in
.
Standard module indicators Local/Remote switch
LEDs
Escape button
Nav+/Nav- switch
(up/down)
Major alarm
Power
Minor
Enter button alarm
Module status
Card extractor
Figure 3-1 MKE-3901Card-Edge LEDs and Module Indicators
D5
D6
D7
D8
Table 3-2 MKE-3901 LED Descriptions
LED Number
D1
D2
D3
D4
LED Name
Lock
AO 1
AO 2
BCG Mix
Key 1
Key 2
Key/MGI
FTB/FTS
Color
Green
Green
Green
Green
Green
Green
Green
Green
Meaning (When Lit)
The module is locked to the reference signal.
The Audio Over 1 function is on air.
The Audio Over 2 function is on air.
A video background transition is in progress.
Key 1 is on air.
Key 2 is on air.
Key 3, 4, 5, or 6 is on air.
Video is black or audio is silent.
Table 3-3 MKE-3901 Module Indicator Descriptions
Module
Indicator
Major Alarm
Color
Red
Meaning (When Lit)
(Not currently active)
IconMaster
Installation and Configuration Manual
59
Table 3-3 MKE-3901 Module Indicator Descriptions (Continued)
Module
Indicator
Minor Alarm
Power
Module Status
Color
Yellow
Green
Green
Meaning (When Lit)
(Not currently active)
The module is receiving power.
The module is configured, loaded, and operational.
MGI-3903 LEDs and Module Indicators
The IconMaster logo inserter has 2 card-edge LEDs and 4 standard module indicators.
CAUTION
Never remove the compact flash card when the Compact Flash Card
Active LED is on or flashing. Doing so may corrupt the files on the card.
The module generates visible alarm signals to alert users of failures or impending failures.
These alarm signals can be found in the following locations:
As red or yellow LEDs on the front module card-edge
As red or yellow LEDs on the 3901AIC Alarm Interconnect Module or the 3901RES-E
Resource Module (visible via light pipes through the NEO frame’s front panel)
As part of a list of activated alarms found in the MGI-3903 Setup menu
Figure 3-2
on page 59 illustrates the locations of the LEDs and standard module indicators on the MKE-3901 module. The meanings of the LEDs are described in
on page 60. The meanings of the module indicators are described in
Standard module indicators Local/Remote switch
LEDs
Ejector
Compact flash card socket
Escape button
Nav+/Nav- switch
(up/down)
Major alarm
Power
Enter button
Minor alarm
Module status
Card extractor
Figure 3-2 MGI-3903 Card-Edge LEDs and Module Indicators
60
Chapter 3
Module Configuration
Table 3-4 MGI-3903 LED Descriptions
LED Indicator
ACT
(Compact flash card active)
MTD
(Compact flash card mounted)
Color Meaning (When Lit)
Amber The flash card is actively being written to or read from. To prevent corruption of the data, do not remove the flash card when this LED is lit.
Green The flash card has been opened and the files recognized by the MGI-3903
Note: A frame’s active resource module provides additional LEDs that indicate conditions not included in these module-specific LEDs. See the card-edge of the resource module for these LEDs.
Table 3-5 MGI-3903 Module Indicator Descriptions
LED Indicator
Major Alarm
Minor Alarm
Power
Module Status
Color
Red
Meaning (When Lit)
There is a problem with the card that will stop the product functioning correctly
Amber There is a minor problem with the card that may reduce the functionality of the product
Green The card is receiving power
Green The module is configured, loaded and operating correctly
4
Router Connections
Sample System Layout
61
Figure 4-1 Sample System Layout Including a Router, PC, Ethernet Switch and IconMaster System
62
Chapter 4
Router Connections
System Configurations—NEO Routers
Note: System configurations for Panacea routers start on page 62. System configurations
for Platinum routers start on page 91.
This section describes the connections that are required in some typical configurations involving NEO NSM internal routers. The following NEO router configurations are described in this section:
IconMaster System with Internal Video NSM Router and Optional ICONM-BO-V Module
IconMaster System with Single Channel Audio and Video NSM Routers and Optional
ICONM-BO-VAC Module
IconMaster System with Internal (Two Channel) Audio and Video NSM Routers and
Optional ICONM-BO-VAC Module
General
Information
Both Video and Audio NSMs
Only one set of NSMs can be installed in a 3RU frame.
The source offset for all NSM modules is 1.
The destination offset for all NSM modules is 0.
Video-Only NSM Modules
The first video NSM module must be assigned an X-Y level of 0.
When ganging 2 cards together, the second module must be assigned an X-Y level of 1.
Audio-Only NSM Modules
The NSM-7×2AES router supports a single AES stream for both A and B inputs on the
IconMaster. If the NSM-7×2AES routers are to be used for discrete AES audio for a full two AES (four-channel) system, four of these router modules are required.
The expected use would be as follows:
NSM #1 and NSM #2 provide AES 1 for Bus A and Bus B.
NSM #3 and NSM #4 provide AES 2 for Bus A and Bus B.
Sample Configuration 1: IconMaster System with Internal
Video NSM Router and Optional ICONM-BO-V Module
This section describes the connections that are required in a typical configurations involving an IconMaster system with an NSM video router module and an optional breakout module.
You can place the NSM modules anywhere in the same NEO frame as the IconMaster system.
Figure 4-3
on page 64 shows a detailed illustration of this process.
1. Configure the NEO NSM Module
1
Set the NEO NSM back module to Unterminated reference:
a
Remove the NSM back module from the NEO frame.
b
Locate jumper JP1 on the NEO NSM back module (see
Figure 4-2
), and then set the
NEO NSM back module to Unterminated reference by setting JP1 as shown.
c
Reinstall the NSM back module into the NEO frame.
IconMaster
Installation and Configuration Manual
63
Jumper JP1 set to
Unterminated
Figure 4-2 Jumper JP1 on the NSM Back Module
2
Connect a maximum of 7 video inputs to the BNC connections labeled In 1 to In 7.
3
Connect Out 1 on the NSM to Input Bus A on the MKE-3901.
4
When using the ICONM-BO-VAC breakout module and NSM routers, audio output 1 from the NSM router must be connected to Bus A In 1 on the breakout module as indicated in
Figure 4-4
on page 65.
64
Chapter 4
Router Connections
When using the ICON-BO-VAB breakout module and NSM routers, the audio output 1 from the NSM router must be connected to Input Bus A1 on the breakout module as indicated in
Table 2-9
on page 54.
Figure 4-3 IconMaster System with Internal Video NSM Router and Optional ICONM-BO-V Module
IconMaster
Installation and Configuration Manual
65
Bus A In 1
Figure 4-4 Audio 1 NSM Connection to ICONM-BO-VAC
2. Make Additional Connections
1
Connect your composite station reference to the Ref Inputs and Genlock connection as shown in
Figure 4-3
.
2
On the MKE-3901 back module, connect Key 1 input source to Key 1 and Fill 1 as appropriate.
3
On the MKE-3901 back module, connect Key 2 input source to Key 2 and Fill 2 as appropriate.
On the MKE-3901 back module, Squeeze Bkgd can be supplied by an external router.
Note: The IconMaster control panel can be connected to any network switch that shares a network with the MKE-3901 and MGI-3903 modules.
4
Connect the two Ethernet ports as follows:
Connect Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through Ethernet cable.
Connect Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
5
Power up the system.
3. Set the IP Address for the MKE-3901 and MGI-3903 Modules
See
on page 99 for more information.
4. Set the NSM Card-Edge Parameters
Note: See the Installation and Operation Manual for your NEO module for more detailed information about setting parameters.
1
Press the left (Esc) button until the NSM message appears on the VFD display
2
Press the right (Sel) button.
3
Use the toggle switch (Nav) to scroll through the parameter list until Setup is highlighted.
4
Press the right (Sel) button.
5
Use the toggle switch (Nav) to scroll through the parameter list until Nav Mode is highlighted.
6
Press the right (Sel) button.
7
Use the toggle switch (Nav) to scroll through the parameter list until All List is highlighted.
8
Press the right (Sel) button.
9
Press the left (Esc) button.
10
Press the left (Esc) button again.
66
Chapter 4
Router Connections
11
Use the toggle switch (Nav) to scroll through the parameter list until XY Level is highlighted.
12
Press the right (Sel) button.
13
Use the toggle switch (Nav) to scroll through the values until 0 (on the first NSM) or 1 (on the second NSM) is reached.
14
Press the left (Esc) button to set the value.
15
Use the toggle switch (Nav) to scroll through the parameter list until SrcOffset is highlighted.
16
Press the right (Sel) button.
17
Use the toggle switch (Nav) to scroll through the values until 1 is reached.
18
Press the left (Esc) button to set the value.
19
Use the toggle switch (Nav) to scroll through the parameter list until DestOffset is highlighted.
20
Press the right (Sel) button.
21
Use the toggle switch (Nav) to scroll through the values until 0 is reached.
22
Press the left (Esc) button to set the value.
Sample Configuration 2: IconMaster System with Single Channel Audio and
Video NSM Routers and Optional ICONM-BO-VAC Module
This section describes the connections that are required in a typical configurations involving an IconMaster system, with single channel audio and video NSM router modules and an optional breakout module. You can place the NSM modules anywhere in the same NEO frame as the IconMaster system.
Figure 4-6
on page 68 shows a detailed illustration of this process.
1. Configure the NSM Modules
Note: The first NSM module will provide Inputs 1 to 5; the second NSM module will provide Inputs 6 to 12.
1
Set the NEO NSM back module to Unterminated reference:
a
Remove the NSM back module from the NEO Frame.
b
Locate jumper J11 on the NEO NSM back module (see
Figure 4-5
).
c
Set the NEO NSM back module to Unterminated reference by setting J11 as shown.
d
Reinstall the NSM back module into the NEO frame.
Jumper JP1 set to
Unterminated
Figure 4-5 Jumper J11 on the NSM Back Module
IconMaster
Installation and Configuration Manual
67
68
Chapter 4
Router Connections
2
On the first NSM back module, connect a maximum of 5 audio inputs to the BNC connections labeled In 1 to In 5.
Figure 4-6 IconMaster System with Internal (Single Channel) Audio and Video NSM Internal Routers and Optional
ICONM-BO-VAC Module
3
On the second NSM back module, connect a maximum of 7 video audio inputs to the BNC connections labeled In 1 to In 7.
IconMaster
Installation and Configuration Manual
69
4
Connect Out 1 on the first NSM to AES Bus A on the MKA-3901. This can be done by direct connection, or by ICONM-BO-VAB or ICONM-BO-VAC breakout module connection.
5
Connect Out 2 on the first NSM to AES Bus B on the MKA-3901.
6
Connect Out 1 on the second NSM to In 6 on the first NSM.
7
Connect Out 2 on the second NSM to In 7 on the first NSM.
2. Make Additional Connections
1
Connect your composite station reference to the Ref Inputs and Genlock connection as shown in
Figure 4-6
.
2
On the MKE-3901 back module, connect Key 1 input source to Key 1 and Fill 1 as appropriate.
3
On the MKE-3901 back module, connect Key 2 input source to Key 2 and Fill 2 as appropriate.
4
On the MKE-3901 back module, Squeeze Bkgd can be supplied by an external router.
Note: If you are connecting Ethernet 1 to a switch, the IconMaster Control Panel must be connected to the same switch
5
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
6
Power up the system.
3. Set the IP Address for the MKE-3901 and MGI-3903 Modules
See
on page 99 for more information.
4. Set the NSM Card-Edge Parameters
Note: See the Installation and Operation Manual for your NEO module for more information about setting parameters.
1
Press the left (Esc) button until the NSM message appears on the VFD display
2
Press the right (Sel) button.
3
Use the toggle switch (Nav) to scroll through the parameter list until Setup is highlighted.
4
Press the right (Sel) button.
5
Use the toggle switch (Nav) to scroll through the parameter list until Nav Mode is highlighted.
6
Press the right (Sel) button.
7
Use the toggle switch (Nav) to scroll through the parameter list until All List is highlighted.
8
Press the right (Sel) button.
9
Press the left (Esc) button.
10
Press the left (Esc) button again.
11
Use the toggle switch (Nav) to scroll through the parameter list until XY Level is highlighted.
12
Press the right (Sel) button.
70
Chapter 4
Router Connections
13
Use the toggle switch (Nav) to scroll through the values until 2 (on the first NSM) or 3 (on the second NSM) is reached.
14
Press the left (Esc) button to set the value.
15
Use the toggle switch (Nav) to scroll through the parameter list until SrcOffset is highlighted.
16
Press the right (Sel) button.
17
Use the toggle switch (Nav) to scroll through the values until 1 is reached.
18
Press the left (Esc) button to set the value.
19
Use the toggle switch (Nav) to scroll through the parameter list until DestOffset is highlighted.
20
Press the right (Sel) button.
21
Use the toggle switch (Nav) to scroll through the values until 0 is reached.
22
Press the left (Esc) button to set the value.
Sample Configuration 3: IconMaster System with Internal (Two Channel)
Audio and Video NSM Routers and Optional ICONM-BO-VAC Module
This section describes the connections that are required in a typical configurations involving an IconMaster system, with two channel audio and video NSM router modules and an optional breakout module. You can place the NSM modules anywhere in the same NEO frame as the IconMaster system.
Figure 4-8
on page 72 shows a detailed illustration of this process.
1. Configure the NSM Modules
Note: The first NSM module will provide Inputs 1 to 5; the second NSM module will provide Inputs 6 to 12.
1
Set the NEO NSM back module to Unterminated reference:
a
Remove the NSM back module from the NEO Frame.
b
Locate jumper J11 on the NEO NSM back module (see
Figure 4-5
).
c
Set the NEO NSM back module to Unterminated reference by setting J11 as shown.
d
Reinstall the NSM back module into the NEO frame.
Jumper JP1 set to
Unterminated
Figure 4-7 Jumper J11 on the NSM Back Module
IconMaster
Installation and Configuration Manual
71
72
Chapter 4
Router Connections
2
On the first NSM back module, connect a maximum of 5 audio inputs to the BNC connections labeled In 1 to In 5.
Figure 4-8 IconMaster System with Internal (Two Channel) Audio and Video NSM Routers and Optional
ICONM-BO-VAC Module
IconMaster
Installation and Configuration Manual
73
3
On the second NSM back module, connect a maximum of 7 video audio inputs to the BNC connections labeled In 1 to In 7.
4
Connect Out 1 on the first NSM to AES Bus A on the MKA-3901. This can be done by direct connection, or by ICONM-BO-VAB or ICONM-BO-VAC breakout module connection.
5
Connect Out 2 on the first NSM to AES Bus B on the MKA-3901.
6
Connect Out 1 on the second NSM to In 6 on the first NSM.
7
Connect Out 2 on the second NSM to In 7 on the first NSM.
Audio output 1 from the third NSM router must be connected to Bus A In 2 on the breakout module as shown in
Figure 4-9
.
Bus A In 2
Figure 4-9 Audio Output 1 From Third NSM Router to Bus A In 2
Audio output 2 from the third NSM router must be connected to Bus B In 2 on the breakout module, as indicated in
Figure 4-10
.
Bus B In 2
Figure 4-10 Audio Output 2 From Third NSM Router to Bus B In 2
When using the IOCON-BO-VAB breakout module, audio output 1 from the third NSM router must be connected to Input Bus A2 on the breakout module, as indicated in
Table
2-9
on page 54.
Audio output 2 from the third NSM must be connected to Input Bus B2 on the breakout module, as indicated in
Table 2-9
on page 54.
System Configurations—Panacea Routers
Note: System configurations for NEO routers start on page 62. System configurations for
Platinum routers start on page 91.
This section describes the connections that are required in some typical configurations involving Panacea external routers. The following Panacea router configurations are described in this section:
IconMaster system with external Panacea video router and optional ICONM-BO-V module
IconMaster System with external Panacea video router and optional ICONM-BO-V module with optional SPT-LSERIAL serial protocol translator
74
Chapter 4
Router Connections
IconMaster system with external Panacea clean quiet video router and optional
ICONM-BO-V module with optional SPT-LSERIAL serial protocol translator
IconMaster system with external Panacea (single channel) audio and video routers and optional ICONM-BO-VAC module with optional SPT-LSERIAL serial protocol translator
IconMaster system with external Panacea (two channel) audio and video routers and optional ICONM-BO-VAC module with optional SPT-LSERIAL serial protocol translator
Sample Configuration 1: IconMaster System, External Panacea Video Router,
Optional ICONM-BO-V Module
This section describes the connections that are required in a typical configurations involving an IconMaster system with a Panacea video router and an optional breakout module.
on page 75 shows a detailed illustration of this process.
1. Configuring the Panacea Router
Before you can make any connections to an IconMaster, the Panacea router must already be configured as desired. If your Panacea router is already operational, you do not need to configure it. If, however, your Panacea router is not already operational, you must install and configure it as desired for your facility. See the Panacea Series Frame and Modules
Installation, Configuration, and Operation Manual for detailed information.
2. Make Connections on the Panacea and ICONM-BO-V Breakout Module
When using the ICONM-BO-V breakout module, the serial port of the Panacea router must be connected to the RS-232/422-A, -B, or -E port on the breakout module as indicated in
.
RS-232/422-E Port
Figure 4-11 RS-232/422-E Port on the ICONM-BO-V Breakout Module
3. Make Connections on the Panacea and MKE-3901
1
On the Panacea back module, connect a maximum of 16 video inputs to the BNC connections labeled Input 1 to Input 16.
2
Connect Output 1 on the Panacea to Input Bus A on the MKE-3901.
3
Connect Output 2 on the Panacea to Input Bus B on the MKE-3901.
4
Connect your station reference to the Sync connection of the Panacea back module.
5
Terminate one of the XY BNC connectors on the Panacea router.
6
Connect the serial port of the Panacea router to Serial Port E in the Multi Function I/O connector on the MKE-3901.
This can be done in either of these two ways.
Direct connection
ICONM-BO-V breakout module connection
IconMaster
Installation and Configuration Manual
75
7
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
Figure 4-12 IconMaster System with External Panacea Video Router and Optional ICONM-BO-V Module
8
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
76
Chapter 4
Router Connections
9
On the MKE-3901 back module, supply Squeeze Bkgd by an external router.
Note: If you are connecting Ethernet 1 to a switch, the IconMaster control panel must be connected to the same network.
10
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
11
Power up the system.
Sample Configuration 2: IconMaster System, External Panacea
Video Router, Optional ICONM-BO-V Module, Optional
SPT-LSERIAL
This section describes the connections that are required in a typical configurations involving an IconMaster system with a Panacea video router, an optional breakout module, and an optional SPT-LSERIAL serial protocol translator.
illustration of this process.
1. Configure the Panacea Router
Before you can make any connections to an IconMaster, the Panacea router must already be configured as desired. If your Panacea router is already operational, you do not need to configure it. If, however, your Panacea router is not already operational, you must install and configure it as desired for your facility. See the Panacea Series Frame and Modules
Installation, Configuration, and Operation Manual for detailed information.
2. Make Connections on the Panacea and ICONM-BO-V Breakout Module
When using the ICONM-BO-V breakout module, the serial port of the Panacea router must be connected to the RS-232/422-A, -B, or -E port on the breakout module as indicated in
.
RS-232/422-E Port
Figure 4-13 RS-232/422-E Port on the ICONM-BO-V Breakout Module
3. Make Connections on the Panacea and MKE-3901
1
On the Panacea back module, connect a maximum of 16 video inputs to the BNC connections labeled Input 1 to Input 16.
2
Connect Output 1 on the Panacea to Input Bus A on the MKE-3901.
3
Connect Output 2 on the Panacea to Input Bus B on the MKE-3901.
4
Connect your station reference to the Sync connection of the Panacea back module.
5
Terminate one of the XY BNC connectors on the Panacea router.
IconMaster
Installation and Configuration Manual
77
6
Connect the serial port of the Panacea router to Serial Port E in the Multi Function I/O connector on the MKE-3901.
This can be done in either of these two ways.
Direct connection
ICONM-BO-V breakout module connection
Figure 4-14 IconMaster System with External Panacea Video Router and Optional ICONM-BO-V Module with
Optional SPT-LSERIAL
78
Chapter 4
Router Connections
7
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
8
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
9
On the MKE-3901 back module, supply Squeeze Bkgd by an external router.
Note: If you are connecting Ethernet 1 to a switch, the IconMaster control panel must be connected to the same switch.
10
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
11
Power up the system.
4. Make Connections on the Panacea and SPT
The IconMaster is installed in the control line, as shown in the example in
The maximum allowable distance for each segment of the X-Y coaxial cable run is
2,000 ft (609 m).
The maximum length for each RS-232 segment is 50 ft (15 m).
The maximum length for each RS-422 segment is 2,000 ft (609 m).
Up to 64 additional serial ports may be added.
on page 79 shows the connector pin assignments on both ends of the
connection (the cable wiring description is shown between the connectors).
IconMaster
Installation and Configuration Manual
79
Figure 4-15 Cable Wiring Details for IconMaster
Table 4-1 Power Requirements for SPT-LSERIAL
PD9200PL6A Adaptor Description
Locations with 110-127 volt electrical systems should use the PD9200PL6A adaptor*
Input voltage: 120 VAC, 60 Hz
Input current: 60 mA max.
Output voltage: 9.0 VDC
Output current: 200 mA
Output connector: 5.5 mm x 2.5 mm female barrel power plug with positive center
PD9300EPL6A Adaptor Description
80
Chapter 4
Router Connections
Table 4-1 Power Requirements for SPT-LSERIAL
PD9200PL6A Adaptor Description
Locations with 220-240 volt electrical systems should use the PD9300EPL6A adaptor
*
Input voltage: 230 VAC, 5 0Hz
Input current: 40 mA max
Output voltage: 9.0 VDC
Output current: 30 0mA
Output connector: 5.5 mm x 2.5 mm female barrel power plug with positive center
* If you did not receive the correct adaptor for your electrical system, please contact your Customer Service representative.
Sample Configuration 3: IconMaster System, External Panacea
Clean/Quiet Switch Video Router, Optional ICONM-BO-V Module,
Optional SPT-LSERIAL
This section describes the connections that are required in a typical configuration involving an IconMaster system with a Panacea clean/quiet switch router, an optional breakout module, and an optional SPT-LSERIAL serial protocol translator.
shows a detailed illustration of this process.
1. Configure the Panacea Router
Before you can make any connections to an IconMaster, the Panacea router must already be configured as desired. If your Panacea router is already operational, you do not need to configure it. If, however, your Panacea router is not already operational, you must install and configure it as desired for your facility. See the Panacea Series Frame and Modules
Installation, Configuration, and Operation Manual for detailed information.
2. Make Connections on the Panacea and ICONM-BO-V Breakout Module
When using the ICONM-BO-V breakout module, the serial port of the Panacea router must be connected to the RS-232/422-A, -B, or -E port on the breakout module as indicated in
.
RS-232/422-E Port
Figure 4-16 RS-232/422-E Port on the ICONM-BO-V Breakout Module
3. Make Connections on the Panacea and MKE-3901
1
On the Panacea back module, connect a maximum of 16 video inputs to the BNC connections labeled Input 1 to Input 16.
2
Connect Output 1 on the Panacea to Input Bus A on the MKE-3901.
IconMaster
Installation and Configuration Manual
81
3
Connect Output 2 on the Panacea to Input Bus B on the MKE-3901.
4
Connect your station reference to the Sync connection of the Panacea back module.
5
Terminate one of the XY BNC connectors on the Panacea router.
6
Connect the serial port of the Panacea router to Serial Port E in the Multi Function I/O connector on the MKE-3901.
82
Chapter 4
Router Connections
This can be done in either of these two ways.
Direct connection
ICONM-BO-V breakout module connection
Figure 4-17 IconMaster System with External Panacea Clean/Quiet Switch Video Router, Optional ICONM-BO-V
Module and Optional SPT-LSERIAL
IconMaster
Installation and Configuration Manual
83
7
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
8
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
9
On the MKE-3901 back module, supply Squeeze Bkgd by an external router.
Note: If you are connecting Ethernet 1 to a switch, the IconMaster control panel must be connected to the same switch.
10
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
11
Power up the system.
4. Make Connections on the Panacea and SPT
The IconMaster is installed in the control line, as shown in the example in
The maximum allowable distance for each segment of the X-Y coaxial cable run is
2,000 ft (609 m).
The maximum length for each RS-232 segment is 50 ft (15 m).
The maximum length for each RS-422 segment is 2,000 ft (609 m).
Up to 64 additional serial ports may be added.
on page 79 shows the connector pin assignments on both ends of the
connection (the cable wiring description is shown between the connectors).
on page 79 shows the power requirements for the SPT-LSERIAL adaptors.
Sample Configuration 4: IconMaster System, External Panacea (Single
Channel) Audio and Video Routers, Optional ICONM-BO-VAC Module, Optional
SPT-LSERIAL
This section describes the connections that are required in a typical configuration involving an IconMaster system with a single channel Panacea audio and video routers, an optional breakout module, and an optional SPT-LSERIAL serial protocol translator.
on page 85 shows a detailed illustration of this process.
1. Configure the Panacea Router
Before you can make any connections to an IconMaster, the Panacea router must already be configured as desired. If your Panacea router is already operational, you do not need to configure it. If, however, your Panacea router is not already operational, you must install and configure it as desired for your facility. See the Panacea Series Frame and Modules
Installation, Configuration, and Operation Manual for detailed information.
84
Chapter 4
Router Connections
2. Make Connections on the Panacea and ICONM-BO-VAC Breakout
Module
When using the ICONM-BO-VAC breakout module and multiple Panacea routers
(multi-level), the audio output 1 from the level 1 Panacea router must be connected to Bus
A In 1 on the breakout module as indicated in
Bus A In 1
Figure 4-18 Audio 1, Level 1 Panacea Connection to ICONM-BO-VAC
Likewise, the audio output 2 from the level 1 Panacea router must be connected to Bus B
In 1 on the breakout module as indicated in
Figure 4-19
.
Bus B In 1
Figure 4-19 Audio 2, Level 1 Panacea Connection to ICONM-BO-VAC
IconMaster
Installation and Configuration Manual
85
Figure 4-20 IconMaster System with External Panacea (Single Channel) Audio and Video Routers, Optional
ICONM-BO-VAC Module, Optional SPT-LSERIAL
86
Chapter 4
Router Connections
Audio output 1 from the level 2 Panacea router must be connected to Bus A In 2 on the breakout module, as indicated in
Bus A In 2
Figure 4-21 Audio 1, Level 2 Panacea Connection to ICONM-BO-VAC
Audio output 1 from the level 2 Panacea router must be connected to Bus B In 2 on the breakout module, as indicated in
Bus B In 2
Figure 4-22 Audio 2, Level 2 Panacea Connection to ICONM-BO-VAC
When using the ICON-BO-VAB breakout module and a Panacea router (single level), audio output 1 from the Panacea router must be connected to Input Bus A1 on the breakout module as indicated in
Likewise, audio output 2 from the Panacea router must be connected to Input Bus B1 on the breakout module as indicated in
Audio output 1 from the level 2 Panacea router must be connected to Input Bus A2 on the breakout module as indicated in
Audio output 2 from the level 2 Panacea router must be connected to Input Bus B2 on the breakout module as indicated in
3. Make Connections on the Panacea and MKE-3901
1
On the Panacea back module, connect a maximum of 16 video inputs to the BNC connections labeled Input 1 to Input 16.
2
Connect Output 1 on the Panacea to Input Bus A on the MKE-3901.
3
Connect Output 2 on the Panacea to Input Bus B on the MKE-3901.
4
Connect your station reference to the Sync connection of the Panacea back module.
5
Terminate one of the XY BNC connectors on the Panacea router.
6
Connect the serial port of the Panacea router to Serial Port E in the Multi Function I/O connector on the MKE-3901. This can be done by direct connection or via the ICONM-BO-V breakout module connection.
7
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
8
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
9
On the MKE-3901 back module, supply Squeeze Bkgd by an external router.
IconMaster
Installation and Configuration Manual
87
Note: If you are connecting Ethernet 1 to a switch, the IconMaster control panel must be connected to the same switch.
10
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
11
Power up the system.
4. Make Connections on the Panacea and SPT
The IconMaster is installed in the control line, as shown in the example in
The maximum allowable distance for each segment of the X-Y coaxial cable run is
2,000 ft (609 m).
The maximum length for each RS-232 segment is 50 ft (15 m).
The maximum length for each RS-422 segment is 2,000 ft (609 m).
Up to 64 additional serial ports may be added.
on page 79 shows the connector pin assignments on both ends of the
connection (the cable wiring description is shown between the connectors).
on page 79 shows the power requirements for the SPT-LSERIAL adaptors.
Sample Configuration 5: IconMaster System with External
Panacea (Two Channel) Audio and Video Routers, Optional
ICONM-BO-VAC Module, Optional SPT-LSERIAL
This section describes the connections that are required in a typical configuration involving an IconMaster system with two channel Panacea audio and video routers, an optional breakout module, and an optional SPT-LSERIAL serial protocol translator.
on page 89 shows a detailed illustration of this process.
1. Configure the Panacea Router
Before you can make any connections to an IconMaster, the Panacea router must already be configured as desired. If your Panacea router is already operational, you do not need to configure it. If, however, your Panacea router is not already operational, you must install and configure it as desired for your facility. See the Panacea Series Frame and Modules
Installation, Configuration, and Operation Manual for detailed information.
88
Chapter 4
Router Connections
2. Make Connections on the Panacea and ICONM-BO-VAC Breakout
Module
When using the ICONM-BO-VAC breakout module and multiple Panacea routers
(multi-level), the audio output 1 from the level 1 Panacea router must be connected to Bus
A In 1 on the breakout module as indicated in
Bus A In 1
Figure 4-23 Audio 1, Level 1 Panacea Connection to ICONM-BO-VAC
Likewise, the audio output 2 from the level 1 Panacea router must be connected to Bus B
In 1 on the breakout module as indicated in
Figure 4-24
.
Bus B In 1
Figure 4-24 Audio 2, Level 1 Panacea Connection to ICONM-BO-VAC
IconMaster
Installation and Configuration Manual
89
Figure 4-25 IconMaster System with External Panacea (Two Channel) Audio and Video Routers, Optional
ICONM-BO-VAC Module, Optional SPT-LSERIAL
90
Chapter 4
Router Connections
Audio output 1 from the level 2 Panacea router must be connected to Bus A In 2 on the breakout module, as indicated in
Bus A In 2
Figure 4-26 Audio 1, Level 2 Panacea Connection to ICONM-BO-VAC
Audio output 1 from the level 2 Panacea router must be connected to Bus B In 2 on the breakout module, as indicated in
Bus B In 2
Figure 4-27 Audio 2, Level 2 Panacea Connection to ICONM-BO-VAC
Audio outputs 3 and 4 from the Panacea level 3 and 4 routers connect to Bus A and B In 3 and 4, respectively.
When using the ICON-BO-VAB breakout module and a Panacea router (single level), audio output 1 from the Panacea router must be connected to Input Bus A1 on the breakout module as indicated in
Likewise, audio output 2 from the Panacea router must be connected to Input Bus B1 on the breakout module as indicated in
Audio output 1 from the level 2 Panacea router must be connected to Input Bus A2 on the breakout module as indicated in
Audio output 2 from the level 2 Panacea router must be connected to Input Bus B2 on the breakout module as indicated in
Audio outputs 3 and 4 from the Panacea level 3 and 4 routers connect to Input Bus A and
B, 3 and 4, respectively.
3. Make Connections on the Panacea and MKE-3901
1
On the Panacea back module, connect a maximum of 16 video inputs to the BNC connections labeled Input 1 to Input 16.
2
Connect Output 1 on the Panacea to Input Bus A on the MKE-3901.
3
Connect Output 2 on the Panacea to Input Bus B on the MKE-3901.
4
Connect your station reference to the Sync connection of the Panacea back module.
5
Terminate one of the XY BNC connectors on the Panacea router.
6
Connect the serial port of the Panacea router to Serial Port E in the Multi Function I/O connector on the MKE-3901.
IconMaster
Installation and Configuration Manual
91
This can be done by direct connection or via the ICONM-BO-V breakout module connection.
7
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
8
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
9
On the MKE-3901 back module, supply Squeeze Bkgd by an external router.
Note: If you are connecting Ethernet 1 to a switch, the IconMaster control panel must be connected to the same switch.
10
Connect the two Ethernet ports as follows:
Ethernet 1 (connection for MKE-3901 control) to a switch using a straight-through
Ethernet cable
Ethernet 2 (two connection options for MGI-3903 control and logo download)
To the same switch as Ethernet 1 using a normal Ethernet cable
To a dedicated switch used for the MGI functionality using a normal Ethernet cable
11
Power up the system.
4. Make Connections on the Panacea and SPT
The IconMaster is installed in the control line, as shown in the example in
The maximum allowable distance for each segment of the X-Y coaxial cable run is
2,000 ft (609 m).
The maximum length for each RS-232 segment is 50 ft (15 m).
The maximum length for each RS-422 segment is 2,000 ft (609 m).
Up to 64 additional serial ports may be added.
on page 79 shows the connector pin assignments on both ends of the
connection (the cable wiring description is shown between the connectors).
on page 79 shows the power requirements for the SPT-LSERIAL adaptors.
System Configurations—Platinum Routers
Note: System configurations for NEO routers start on page 62. System configurations for
Panacea routers start on page 62.
This section describes the connections that are required in some typical configurations involving Platinum external routers. The following Platinum router configurations are described in this section:
IconMaster System, External Platinum Video Router, Optional ICONM-BO-V Module
Sample Configuration 2: IconMaster System, External Platinum Video Router, Optional
HView SX Hybrid multiviewer, Optional JLCooper eBOX, Optional ICONM-BO-V Module
92
Chapter 4
Router Connections
Sample Configuration 1: IconMaster System, External Platinum Router,
Optional ICONM-BO-V Module
This section describes the connections that are required in a typical configurations involving
Platinum external routers.
on page 93 shows a detailed illustration of this
process.
1. Configure Platinum Router
Before you can make any connections to an IconMaster, the Platinum router must already be configured as desired. If your Platinum router is already operational, you do not need to configure it. If, however, your Platinum router is not already operational, you must install and configure it as desired for your facility. See the Platinum Series Frames and Modules
Installation, Configuration, and Operation Manual for detailed information.
On your Platinum router configuration, make sure that you set the video and audio to different levels. For example, if you set the video level to “0,” set the audio level to “1” or higher.
2. Make Connections between the Platinum and MKE-3901
1
On the Platinum router, connect the inputs to the input BNC connections on the appropriate Platinum modules.
2
Terminate the loop-thru (XY) BNC connectors on the communications back panel (PT-CBP).
3
Connect the first desired output on the PT-CBP to Input Bus A on the MKE-3901.
4
Connect second desired output on the PT-CBP to Input Bus B on the MKE-3901.
5
On the PT-CBP, connect the station reference to one connector on an available Sync connection.
6
On the MKE-3901 back module, connect the signal Squeeze Bkgd input to an output on the PT-CBP.
Note: The Platinum router serial port baud rate must be set to 38400. IconMaster can control the Platinum over Ethernet.
7
Connect an available serial port (SERIAL1 or SERIAL2) on the PT-CBP to Serial Port E in the
Multi Function I/O connector on the MKE-3901. This can be done by direct connection or by
ICONM-BO-V breakout module connection. When using the ICONM-BO-V breakout module, either serial port of the PT-CBP must be connected to the RS-232/422-A, -B, or -E
IconMaster
Installation and Configuration Manual
93 port on the breakout module as indicated in
Figure 4-29
on page 94.
Figure 4-28 IconMaster System with External Platinum Router Using Serial Control and Optional ICONM-BO-V
Module
94
Chapter 4
Router Connections
RS-232/422-E Port
Figure 4-29 RS-232/422-E Port on the ICONM-BO-V Breakout Module
8
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
9
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
Note: If you are connecting Ethernet 1 to a network hub/switch, the IconMaster control panel must be connected to the same switch.
10
On the MKE-3901 back module, connect the Ethernet 1 connection for MKE-3901 control to a network hub/switch using a straight-through Ethernet cable.
11
On the MGI-3903 back module, two Ethernet connection options for MGI-3903 control and logo download as follows:
To the same network/hub as Ethernet 1 using a normal Ethernet cable.
To a dedicated switch used for the MGI functionality using a normal Ethernet cable.
12
Power up the system.
Sample Configuration 2: IconMaster System, External Platinum Router, HView
SX Hybrid, JLCooper eBOX, ICONM-BO-V Module
This section describes the connections that are required in a typical configurations involving
Platinum external routers.
on page 96 shows a detailed illustration of this
process.
1. Configure HView SX Hybrid Module
Before you can make any connections to an IconMaster, the HView SX Hybrid multiviewer output module must already be installed and configured in the Platinum frame. See the
HView SX Hybrid Multiviewer Installation, Configuration, and Operation Manual and the
HView SX Hybrid Layout Designer User Guide for detailed information.
2. Set up eBOX to work with HView SX Hybrid
You will need to configure some settings for the multiviewer in your Layout Designer software before you can use the eBOX with HView SX Hybrid.
1
Right click on the HView SX Hybrid device in the Multiviewers window of Layout Designer.
2
Select Advanced Configuration.
3
Select the External Devices tab.
4
Select the desired HView SX Hybrid’s “-1” configuration.
5
Under Type, select TSL Protocol.
6
Under Port, select TCP/IP.
7
Under IP, enter the IP address and port.
The default IP is 192.168.254.102.
IconMaster
Installation and Configuration Manual
95
The default port is 23.
8
Click Add.
9
Click Done.
3. Configure Platinum Router
Before you can make any connections to an IconMaster, the Platinum router must already be configured as desired. If your Platinum router is already operational, you do not need to configure it. If, however, your Platinum router is not already operational, you must install and configure it as desired for your facility. See the Platinum Series Frames and Modules
Installation, Configuration, and Operation Manual for detailed information.
96
Chapter 4
Router Connections
On your Platinum router configuration, make sure that you set the video and audio to different levels. For example, if you set the video level to “0,” set the audio level to “1” or higher.
Figure 4-30 IconMaster System with External Platinum Router Using Ethernet Control, HView SX Hybrid, eBOX, and Optional ICONM-BO-V Module
IconMaster
Installation and Configuration Manual
97
4. Make Connections between HView SX Hybrid Multiviewer and
JLCooper eBOX
Before you can make any connections to an IconMaster, the JLCooper eBOX must already be configuredto work with your multiviewer. For information about configuring your e-BOX, see your JLCooper eBOX documentation.
5. Make Connections between the Platinum and MKE-3901
1
On the Platinum router, connect the inputs to the input BNC connections on the HView SX
Hybrid modules.
2
Terminate the loop-thru (XY) BNC connectors on the communications back panel (PT-CBP).
3
Connect the first desired output on the PT-CBP to Input Bus A on the MKE-3901.
4
Connect second desired output on the PT-CBP to Input Bus B on the MKE-3901.
5
On the PT-CBP, connect the station reference to one connector on an available Sync connection.
6
On the MKE-3901 back module, connect the signal Squeeze Bkgd input to the output on the PT-CBP.
Note: The Platinum router serial port baud rate must be set to 38400.
7
Connect an available serial port (SERIAL1 or SERIAL2) on the PT-CBP to Serial Port E in the
Multi Function I/O connector on the MKE-3901. This can be done by direct connection or by
ICONM-BO-V breakout module connection. When using the ICONM-BO-V breakout module, either serial port of the PT-CBP must be connected to the RS-232/422-A, -B, or -E port on the breakout module as indicated in
RS-232/422-E Port
Figure 4-31 RS-232/422-E Port on the ICONM-BO-V Breakout Module
8
On the MKE-3901 back module, connect the Key 1 input source to Key 1 and Fill 1 as appropriate.
9
On the MKE-3901 back module, connect the Key 2 input source to Key 2 and Fill 2 as appropriate.
Note: If you are connecting Ethernet 1 to a network hub/switch, the IconMaster control panel must be connected to the same network.
10
On the MKE-3901 back module, connect the Ethernet 1 connection for MKE-3901 control to a network hub/switch using a straight-through Ethernet cable.
11
On the MGI-3903 back module, two Ethernet connection options for MGI-3903 control and logo download as follows:
To the same network/hub as Ethernet 1 using a normal Ethernet cable.
To a dedicated switch used for the MGI functionality using a normal Ethernet cable.
12
Power up the system.
98
Chapter 4
Router Connections
5
Configuring IP Addresses
Setting the IP Address for the MKE-3901 Module
1
Press the left (Esc) button until the message MKE3901 appears on the VFD display.
2
Press the right (Enter) button.
3
Use the toggle switch (Nav) to scroll through the parameter list until Status is highlighted.
4
Press the right (Enter) button.
5
Use the toggle switch (Nav) to scroll through the parameter list until Other is highlighted.
6
Press the right (Enter) button.
7
Use the toggle switch (Nav) to scroll through the parameter list until IP_Address is highlighted.
8
Press the right (Enter) button.
9
Continue pressing the right (Enter) button until the cursor is under the digit you want to change.
10
Use the toggle switch (Nav) to change the digit.
11
Press the right (Enter) button to move to the next digit.
12
Repeat the previous three steps until you have changed the IP address.
13
Press the right (Enter) button until the cursor is under the space at the end of the IP address.
14
Press the left (Esc) button to accept the change.
Setting the IP Address for the MGI-3903 Module
1
Press the left (Esc) button until the message MGI-3903-R appears on the VFD display.
2
Press the right (Enter) button.
3
Use the toggle switch (NAV) to scroll through the parameter list until IP_Address is highlighted.
4
Press the right (Enter) button.
5
Continue pressing the right (Enter) button until the cursor is under the digit you want to change.
6
Use the toggle switch (Nav) to change the digit.
7
Press the right (Enter) button to move to the next digit.
8
Repeat the previous three steps until you have changed the IP address.
9
Press the right (Enter) button until the cursor is under the space at the end of the IP address.
99
100
Chapter 5
Configuring IP Addresses
10
Press the left (Esc) button to accept the change.
Changing the Control Panel IP Address
1
To access the service menu:
On an ICONM-RCP, simultaneously press all four LCD buttons in the center Parameter
Control Cluster
On an ICONM-RCP16 panel, press the right control knob
2
Turn the left scroll knob until the PNL IP ADDR parameter appears.
Reading from left to right, you will see a display of the control panel’s current IP address.
3
Select the button that contains the IP address component that you want to change, and then turn the right scroll knob to change the number on that button.
4
After you enter the last digit of the IP Address, press the right knob to save the new IP
Address.
5
When finished, turn the left scroll knob until the PUSH EXIT parameter appears.
Set the IP Address for the 3901RES-E Module
To use CCS-P control and monitoring of your IconMaster master control switcher, Navigator and NUCLEUS operate through the frame’s optional 3901RES-E module.
To change the resource module network settings, at least one of the processing modules in the frame must support the Frame IP feature.
Note: The IRB-3901, GPI-3901, and MGI-3901 NEO modules do not support Frame IP.
Some older NEO modules that have not been upgraded also do not support this feature.
To configure the IP address for this module, follow these steps:
1
Using the card-edge of a NEO processing module in the same frame as the resource module, scroll down and then select the Setup menu at the end of the parameter list.
2
Select Frame IP, and then press the Enter button.
3
Select IP Address, and then press the Enter button.
The card-edge screen shows the current IP Address of the active resource module.
If the message Not Supported appears, correct the problem by ensuring that the active resource module’s SW2 DIP 8 is in the down position.
4
Using the Enter button, scroll to the digit in the IP Address.
5
Press the toggle switch up or down to change the IP number, and then scroll past the end of the number to accept the change.
The following tips will help you enter an IP address:
To backspace from the selected number in the IP to the one before it, scroll using the
Nav+/Nav- until you reach the back arrow ( ), and then press the Enter button.
IconMaster
Installation and Configuration Manual
101
Delete the selected number in the IP by scrolling using the
Nav+/Nav- switch until the delete character ( X ) is displayed, and then press the
Enter button.
(The delete character is located after the number “0”)
Use Nav+ (up) to scroll up through numbers, increasing the selected number.
Use Nav- (down) to scroll down through numbers, decreasing the selected number.
6
Press the Escape/Exit button, and then repeat the number changing process for the
Subnet and Gateway if necessary.
7
Press the Escape/Exit button twice to send the new IP Address to the resource module.
8
Reboot the resource module by pulling it out of its slot and reinserting it.
9
Confirm the resource module’s corrected IP Address by again using the card edge to verify the IP Address, Subnet, and Gateway IP settings. Then ping the resource module via the PC, as described in the following steps:
a
Click Start, point to Programs > Accessories and then click Command Prompt to open the Command Prompt window on the PC.
b
After the command prompt, type the following message, and then press ENTER: ping 192.168.248.50 (or the actual IP Address of your resource module)
The message should reply back. If the ping does not work, see
Initializing
IconMaster
Once you have completed the system wiring, the following settings are required:
Network settings
Operating standard
System timing
Network
Settings
The default IP address will function correctly in a “one frame and one panel” configuration if both frame and panel are connected to the same switch that is not connected to a network server or router.
If you have changed the IP address on the card edge of the MKE-3901 module, you must
make the same change in the Network dialog box in the ICU software (see page 176).
To change the network settings of the IconMaster control panel, refer to the Panel Network
Configuration dialog box in ICU software (see page 185). Alternatively, you can use the
Service Menu change the IP address of the IconMaster control panel on the panel itself.
Refer to the IconMaster Functional Operation and Configuration Manual for more information.
Operating
Standard
To change the operating standard, use the Genlock and Standards dialog box in the ICU
Note: When changing between HD operating standards (for example, from 1080I to 720P), you must repower the IconMaster.
102
Chapter 5
Configuring IP Addresses
System
Timing
To make changes to the IconMaster timing, use the Genlock and Standards dialog box in
the ICU software (see page 168).
6
Connecting an IconMaster to an
EAS Device
103
Overview
The federal Emergency Alert System (EAS) enables broadcasters, cable providers, and emergency managers to receive, store, forward, and originate emergency alert messages as required by the Federal Communications Commission. EAS allows broadcast stations, cable systems, participating satellite companies, and emergency managers, and other services to send and receive emergency information quickly and automatically, even if these facilities are unattended. Specially equipped devices decode EAS messages for distribution.
The IconMaster can be connected directly to an EAS encoder/decoder or character generator, thus enabling you to insert emergency notification messages directly into the broadcast stream as a regular scrolling text crawl.
An external EAS receiver is required to allow this feature to become operational.
Communication Protocols
The IconLogo currently supports three communication protocols employed by EAS devices:
TFT
1
, Sage
2
, and Gorman-Redlich (GR)
3
.
RS-232 Connection
The EAS device is connected to the RS-232-D port on the IconMaster ICONM-BO-V breakout module. See
on page 38 for pinout details. If the IconMaster ICONM-BO-V
breakout module is not being used, the EAS device must be wired directly to the
Multi-Function I/O connector on the MKE-3901-BM (see
(RS-232-D-RX) and 58 (RS-232-D-TX) are reserved for this purpose. See
on page 28. (One ground connection is also required.)
Configuring the EAS
Device
EAS devices need to be set to 9600 baud and Standard or Generic CG protocol in order to work correctly with IconMaster.
For basic configurations and preparations please see the specific EAS device user manual. No additional special settings are needed to communicate with an IconMaster. The standard signal will be taken out from the EAS device’s serial port.
1
“TFT” is a trademark of TFT Inc., San Jose, California.
2
“Sage” systems are products of Sage Alerting Systems, Rye Brook, New York.
3
Gorman-Redlich Manufacturing Co., Athens, Ohio.
104
6
Connecting an IconMaster to an EAS Device
IconMaster can be configured two different ways when using IconMaster's Audio Over to insert the EAS audio message into the program stream.
An important consideration is that the EAS audio message is not always the same duration as the EAS logo message.
Method 1 (preferred): IconMaster controls EAS logo insertion and EAS audio insertion separately.
1
Configure the EAS receiver to output a GPI output for the duration of the audio message.
2
Connect this GPI output to an IconMaster GPI input, and configure IconMaster to use this
GPI input as Key to Air (as in
) so that the EAS Box can hold the Audio Over
active for the duration of the EAS audio message.
Figure 6-1 GPI Settings for EAS Logo Insertion
3
Ensure that the EAS Audio setting in the System Configuration menu is set to NONE.
Figure 6-2 EAS Audio Settings in the System Configuration Menu
With these settings, IconMaster will enable the selected Audio Over whenever the GPI input is triggered, and for as long as the GPI input is triggered. The duration of the Audio Over key is independent of the duration of the EAS message.
Method 2: IconMaster controls EAS logo and audio together.
IconMaster can be configured to automatically enable an Audio Over when an EAS message is received.
The following menu can be found in the ICU System Configuration screen, and shows that Audio Over 1 will automatically be keyed into PGM video when an EAS message is received, and only for the duration of the EAS message.
IconMaster
Installation and Configuration Manual
105
Figure 6-3 EAS Audio Settings in the System Configuration Menu
Creating an EAS Text Crawl
The following steps are involved in setting up EAS.
1
Create fonts using Content Editor.
See
Using the Font Utility
on page 159.
2
Create a Text Crawl in Logo Soft Panel.
See
Configuring a Text Crawl or Text Titling
on page 107.
3
Create a Quick Select logo.
See
Logo Number
on page 88.
4
Select Eng > More > EAS Logo, enter the number of the text crawl logo you created (in
Step 2) in the TextLogo field, and then press QuickSelect.
See
EAS Logos1
on page 127.
5
Select Eng > More > EAS Protocol and choose the EAS protocol your system uses.
6
(Optional) Configure EAS audio on the System Config screen in the IconMaster
Configuration Utility (in the section of the screen labeled EAS Audio).
If you want audio triggered by GPI from the EAS receiver (so it does not get cut off if it is longer than the text crawl), select None and then configure a GPI as follows.
a
On the IconMaster Configuration Utility, select GPI, and then click Add GPI.
b
Select the number of the GPI you want to configure, and make the following settings:
Assignment—A/O to Air
Polarity—Open
Trigger—Level
c
Save the configuration and download it to the frame.
106
6
Connecting an IconMaster to an EAS Device
7
Machine Control
Connecting for Machine Control Use
Note: You cannot use this configuration on a network.
The serial connector RS-232-A on the ICONM-BO-V video breakout module is dedicated for machine control use. To connect the IconMaster system to a VTR, follow these steps.
1
Using a straight-through RS-232 serial cable, connect RS-232-A on the ICONM-BO-V video breakout module to the serial connector on an SPT-LSERIAL or an SPT-LXYTOXY serial protocol translator.
Note: If re-assigned to port B or port E, use a null-modem cable instead of this straight-through cable.
2
Using a coaxial cable, connect COAX on the SPT to COAX on the VTR specific SPT. (For example, if you are connecting to a Sony VTR, you would be using an SPT-LXYTOSONY.)
3
Using an RS-422 serial cable, connect the serial connector on the SPT to the VTR.
4
Follow the VTR manufacturer’s instructions for other connections to the IconMaster system.
Figure 7-1
shows a sample connection using a Sony tape machine.
107
ICONM-BO-V Video Breakout Module
Figure 7-1 Sample Sony Machine Control Connections
108
Chapter 7
Machine Control
Edge Protocol Gateway
The Edge protocol gateway provides external connectivity to any Leitch/Imagine
Communications routing system. It translates between Leitch/Imagine Communications and other manufacturers’ routing control systems. On an IconMaster system, the Edge would be connected to either a Panacea or a Platinum router to access third-party protocols and commands.
Before you can make any connections to an IconMaster, the Edge must already be configured as desired. If your Edge is already operational, you do not need to configure it.
If, however, your Edge is not already operational, you must install and configure it as desired for your facility. See the Edge Protocol Gateway Installation and Frame Configuration
Manual for detailed information.
You can use an Edge to allow the IconMaster to “talk” to certain third party routing systems. See the Protocol Translation Functions Firmware Installation, Configuration, And
Operation Manual for a list of supported third-party protocols and commands.
8
Logging Server
Installing Magellan Logging Server
The Magellan Logging Server is purchased separately. It is installed on a PC on the same network as the IconMaster switcher, and receives messages designated by the system administrator for review.
System Requirements
Hardware Requirements
Magellan Logging Server can be installed on a PC that meets or exceeds the following requirements:
3 GHz Pentium IV processor (Core 2 Duo - 2.39 GHz recommended)
1 GB RAM (2 GB recommended)
100-BaseT Network connection
Minimum 20 GB HDD drive
1 GB Available Disk Space
DVD-ROM Optical Drive
Super VGA supporting 1152 × 864 (19-inch recommended) Display
Operating System
Choose one of the following:
Windows 7 32-bit
Windows 7 64-bit
Windows Server 2008 R2 64-bit
Required Software
The following software must be installed prior to installing Magellan Logging Server
(Magellan Diagnostic Logging):
Microsoft .NET 4 Client Profile
Microsoft .NET 4 Extended
109
110
Chapter 8
Logging Server
Microsoft .NET Framework 3.5.1 Feature (Microsoft Windows Server 2008 r2 only)
Microsoft Silverlight 5.1 or higher
Microsoft Visual C++ 2010 x64 Redistributable for Windows 7 64bit
Installing the Logging Server
Double-click the correct file, depending on your operating system:
MagellanDiagnosticLogging32-BitNetworkServerandClientRuntime xx.xx.xx.msi
MagellanDiagnosticLogging64-BitNetworkServerandClientRuntime xx.xx.xx.msi
Magellan Diagnostic Logging Server uses InstallShield. Follow the instructions that appear on the screen. It is not necessary to reboot the PC after installing the software.
Configuring IconMaster for Magellan Logging Server
IconMaster requires a license for Magellan Logging Server. To acquire a license, contact
Customer Service. See
Getting Help from Customer Service
information. Licenses are added to IconMaster using the IconMaster configuration utility software. See
Use IconMaster configuration utility software to configure IconMaster to send messages to the logging server. See
IconMaster requires an SNTP server to provide correct time in messages from IconMaster to the Logging Server. To configure IconMaster to connect to an SNTP server, turn on UTC time in the ICU by configuring the Clock section of the Clock and Timer tab. See
Launching Magellan Logging Server
To launch the Magellan Logging Server, do one of the following:
From the Start menu, select All Programs > Imagine Communications > Magellan
Diagnostic Logging > Diagnostic Logging Viewer.
In the URL field of your browser, type http://localhost:8002/
IconMaster
Installation and Configuration Manual
111
The home page of Magellan Logging Server lists all devices configured to send messages to the server.
Figure 8-1 Home Page of the Magellan Logging Server
The Logging Server’s Home tab displays a list of devices that send it messages. The logging server in
has received log messages from three IconMaster devices, named
Log-1, Log-2, and Log-3.
Each IconMaster has a single sub-device that you can view by clicking the down arrow.
Below the sub-device is the log. To view a summary of the log for a device, click History at the lowest level of the log entry.
112
Chapter 8
Logging Server
Figure 8-2 History for an IconMaster Device
Viewing
Logs
To view a log, place a check beside the device on the Home page, and then click View Live
Logs.
Figure 8-3 Live Logs for Three IconMaster Systems
If no logs are selected or all logs are selected, click View Live Logs and the log that opens will contain entries for all connected devices.
IconMaster
Installation and Configuration Manual
113
If no device has activity when you select View Live Logs, the viewer tab is empty. The viewer updates dynamically as events occur.
Examine
Logs
On the Home tab, select devices (if no devices are selected, it’s the same as if all of them are) and click Examine Logs to view logs in detail.
Figure 8-4 Examining a Log
The top portion of the Examiner tab shows a timeline. A green marker indicates the beginning of the viewing area, and a red marker indicates the end.
To View a specific time, click the timeline with the mouse. The log examiner updates to show logs surrounding that time. A black line appears in the timeline, indicating the current time in the Examiner.
Above the timeline, you can adjust the content that is displayed by changing the date and duration. To view a different part of the log, drag the green and red sliders.
Below the timeline, messages are displayed in a static format. You can sort the log entries by clicking on column headers.
Changing the Content Displayed in the Examiner
In addition to sorting a log file by the display columns, you can choose to view only certain types of logs. Follow these steps:
1
Click Show Options.
114
Chapter 8
Logging Server
The View Options palette appears at the right side of the screen.
Figure 8-5 Show Options while Examining a Log
2
At the top of the palette, select how many logs to view, and how they will be displayed.
3
Place checks beside types of information you would like to see in the Examiner.
You can only filter out information that is being sent already from the IconMaster. Settings, configured using the IconMaster Configuration Utility supercede settings on this screen.
4
Click Apply.
The table refreshes to display the selected information.
Export Logs
When you export a log, it is saved as a zip file that can be viewed by any log viewer.
1
Do one of the following:
From the Logging Server’s Home page, do either of the following:
At the right end of the IconMaster’s header line, click Export, and then choose
Past Day, Past Week, or All Logs.
Place checks beside items in the Devices and Application Profiles list, and then click
Show Filters/Actions, and then click Export under Actions. Choose Past Day,
Past Week, or All Logs.
All selected logs (any log with a check beside it) are exported.
From the Examiner, click Show options, and then, under Actions, click Export.
Choose Logs in View, Past Day, Past Week, or All Logs.
IconMaster
Installation and Configuration Manual
115
From the History tab, place a check beside the logs you want to export, and then click
Export.
When the log is collated and ready to be saved locally, a dialog may appear, asking what to do with the file.
2
Click Save to save the file to the local computer. You can choose a different location for the file.
If this dialog does not appear, but a progress bar appears instead, the file is being transferred to the local computer.
When the export has finished, a message appears on the top left corner of the Logging
Server interface.
Import Logs
The Magellan Logging Server can import logs that it or another Magellan Logging Server has saved. To import a log, follow these steps:
1
Click Import and View Collections at the bottom of the Home page.
The lower section of the screen expands to display something similar to
:
Figure 8-6 Import and View Collections -- Opened
2
Click Import Logs and then browse to a .zip file and click Open.
A progress bar appears, and when the import is finished, an Import Complete message appears in the top right corner of the screen.
3
Click an item in the Log Collections column on the left.
The Collection Devices column updates to display all devices contained in that collection.
Within each device are nested folders for each sub-device. IconMaster devices normally have one sub-device.
4
Place a check beside each device log you would like to load in the examiner, and then click
Examine Logs.
The logs open in the Examiner. For more information, see
Collect Logs
A collection is a group of logs that you group yourself.
1
On the Home tab, click Show Filters/Actions.
2
The Filters/Actions panel opens.
116
Chapter 8
Logging Server
3
Click Actions > Collect logs to network.
The following dialog box opens:
Figure 8-7 Collecting Logs to Network
4
Enter a name for the collection, and any comments that might help identify the purpose of the collection or its contents later.
5
Select a time frame, and choose whether to collect logs immediately, or begin collection at some later point.
6
Click Collect to activate the collection.
Using
Summaries
If you have recently imported or exported a log, the Summary bar appears below the button bar at the top of your Logging Server screen. If the Summary bar is not open, click
Summary to open it.
Figure 8-8 Summary Button
The Summary bar has three options: Exports, Imports, and Collections.
Click one of these options to open the Summary Details dialog box.
IconMaster
Installation and Configuration Manual
117
The three options correspond to three tabs on the Summary Details dialog box.
Figure 8-9 Summary Details Dialog Box
Each tab details recent activity for that area of the interface.
Clearing the Logging Server
When you clear logs from the logging server, all devices are also removed. Be sure to save logs that you need prior to clearing.
1
If the Filters palette is not open at the right side of the screen, click Show Filters/Actions.
2
Click Clear All Logs and then click OK.
All logs and all information in the logs are removed.
When a device has activity, it will reappear on the Home page of the logging server.
Configuring Magellan Logging Server
Click Settings in the top right corner of the screen to open the Settings pane.
118
Chapter 8
Logging Server
For the most part, don’t change port numbers and other settings except on the advice of
Customer Service.
Some settings that can customize system performance include:
Minimum Log Interval
Columns and column order
If your logging server is not receiving any messages, despite having devices configured, check Receive Messages over SysLog. If this item is not checked, no messages will be received.
When you make any changes to the Logging Server’s settings, click Save to commit the changes.
Changing Columns That Appear in Magellan Logging Server
1
On the Settings panel, scroll down to Column References.
Figure 8-10 Column References Selector in Magellan Logging Server
The items in the list on the left are not currently used in the Log display. Items in the list on the right are column headers in the Log display.
To move items from one column to the other, click on the item and hold the mouse down while dragging from one column to the other. When you see a shadow of the item in the column you’re dragging to, release the mouse button. The item appears at the point in the list where you dropped it.
You can change column order by dragging items within a column.
Note: You can also drag column headers on the table interfaces themselves.
2
Click Save to commit the changes.
Changes to columns are universal and apply to all examiner pages.
IconMaster
Installation and Configuration Manual
119
Interpreting IconMaster Messages in the Logging Server
To find items specific to a particular IconMaster in the server log, look for the name as defined in the IconMaster Channel Name on the Network dialog box of ICU. See
Information such as Date, Time, Level, Sequence, etc., in the logging server is defined by the logging server itself; see the Logging Server’s documentation for more information on those items.
The Message field in the logging server is specific to the particular device. A single device action, such as a Take, can trigger numerous messages in the log, as the repercussions of that action are executed.
The message field of a typical IconMaster log entry is separated by commas, and contains the following information:
The source of the change, for example: Operation, meaning an operator performed an action)
The device where the action took place, for example RCP: IP address, meaning a specific remote control panel triggered an action
The item that was triggered
The action that happened as a result of the triggered item
Figure 8-11 Sample Log File from Logging Server
The log entries in
describe the ICU configuration file being updated on the
IconMaster and the system rebooting itself in order to accept the changes.
Error: This level is reserved for problems that directly affect output, such as loss of signal and loss of reference. High-priority CCSP alarms with a level of Critical generate this message when asserted.
Warning: This level notifies about potential problems. Medium-priority CCSP alarms with a level of Warning generate this message when asserted.
Notice: These messages apply to all alarm de-assertions and RCP connection messages.
Informational: This level indicates routine device operation.
120
Chapter 8
Logging Server
Debug: This level is disabled by default and only intended for use in specific trouble-shooting guided by Imagine Communications tech support.
Informational messages will be generated for all operational changes from control sources enabled in the logging server setup. Control by RCP will list the IP of the device to identify which one performed the operation. Other sources have a sole source available - all
Automation message are assumed to come from the same source, but EAS is considered another source. All messages control from the parametric system are identified as CCSP.
9
Automation Setup
Connecting a DAL Automation System to IconMaster
The following information is specific to a DAL Automation system used with the McCurdy
SER-8-IF serial breakout box, and may not apply to any other automation system setups.
1
Using the cable provided, connect the DAL Automation System to port J19 on the McCurdy
SER-8-IF serial breakout box.
2
Choose one of the following options:
If using the IconMaster ICONM-BO-V breakout module, connect port RS-232/422-B on the ICONM-BO-V module to the port on the McCurdy SER-8-IF serial breakout box configured for automation. See
on page 23 for setting the serial port standard.
7
8
IconMaster
Pin Function
2
3
TX- (data sent by router) <===> 6
RX+ (data received by router) <===> 1
RJ45 Port
Pinouts
*
TX+ (data sent by router)
RX- (data received by router)
<===>
<===>
3
2
8
4
9
McCurdy Breakout
Pin
5
Function
Rx -
Tx +
Rx +
Tx -
* For use with SER16 D-Series adapter
If connecting directly to the IconMaster system, connect the multifunction I/O on the
MKE-3901-BM to the port on the McCurdy SER-8-IF serial breakout box configured for automation. See
setting the serial port standard.
IconMaster
Pin Function
20 RSxx2-B TX -
14 RSxx2-B RX +
41 RSxx2-B TX +
15 RSxx2-B RX -
* For use with SER16 D-Series adapter
<===> 6
<===> 1
<===> 3
<===> 2
RJ45 Port
Pinouts
*
4
9
5
8
McCurdy Breakout
Pin Function
Rx-
Tx+
Rx+
Tx-
121
122
Chapter 9
Automation Setup
D-Series System Capabilities With IconMaster
The ADC-100 playout automation includes support for controlling the IconMaster master control switcher.
The following IconMaster capabilities are supported:
Transitions between main sources (V-fade, cut-fade, fade-cut, and mix) at three predefined speeds (slow, medium and fast) in addition to cuts.
Audio-Overs with either of two external inputs
Control of the six IconMaster keyers (two using external key/fill source, four using the internal logo store).
Selection of logos from the IconMaster’s internal logo store (this requires configuring a corresponding source machine entry in the source specification table src.tbl.
Control of effects (this is not functioning correctly with IconMaster firmware v1.4).
Audio-video breakaways not supported: Although the IconMaster supports audio-video breakaways under certain circumstances, using an audio-video break away interferes with
IconMaster functions, so the D-Series interface does not support using this capability.
The IconMaster should be running firmware release 1.4 or later. This interface will not function properly with earlier IconMaster firmware versions.
Configuration
Serial Port Configuration in port.cfg
Serial Port
Configure the serial port used to communicate with the IconMaster with
USAGE=swrn SPEED=38400 NDATA=8 PARITY=NONE NSTOP=1 DUPLEX=FULL
HANDSHAKE=NONE, where n is the index of the swr.tbl entry describing the IconMaster switcher.
Breakout Module Connection
Connect the automation serial port to the connector labeled RS232/422-B on the
IconMaster breakout module.
This port can be configured for either RS-232 or RS-422 connections.
Ensure both jumper J18 of the MKE-3901 board and the jumper pack A1 on the breakout module are both set to match the appropriate serial communication standard
(normally RS-422 for a D-MAS system using McCurdy SER-4, SER-8 or SER-12 card via a
CON-8 or MUX8/800).
IconMaster
Installation and Configuration Manual
123
Switcher Configuration in swr.tbl
An IconMaster switcher requires the following settings in the swr.tbl specification table.
Table 9-1 swr.tbl Specification Settings
swr.tbl Field
Switcher type
Description
Parameter
Number of Outputs
Number of program inputs
Number of program levels
Number of over inputs
Number of over levels
Switcher Latency time
Set to
ICONMASTER
Text describing switcher
Leave Blank
1
Number of valid inputs (between 1 and 12)
1
1 for a single audio-over input, or 2 if both audio-over inputs are used
9 blank (or a time in format ss:ff)
Level Mappings for IconMaster
The automation main audio and video levels are always mapped to the audio and video levels of the IconMaster. The mapping of D-MAS subevent fields and switching levels to the keyers, audio mixer and DVE engine of the IconMaster is controlled by the Switcher Level n fields in swr.tbl.
If a Switcher Level n field is left blank, the corresponding facility of the IconMaster is not associated with an automation switching level and is not used.
Table 9-2 swr.tbl Mapping
swr.tbl Field
Switcher Level 1
Switcher Level 2
Switcher Level 3
Switcher Level 4
Switcher Level 5
Switcher Level 6
Switcher Level 7
Switcher Level 8
Maps Requests to
Keyer 1 (external source)
Keyer 2 (external source)
Keyer 3 (internal logo source)
Keyer 4 (internal logo source)
Keyer 5 (internal logo source)
Keyer 6 (internal logo source)
DVE/Squeezeback engine
Voice-Over Mixer
124
Chapter 9
Automation Setup
Switcher Configuration in bus.tbl
To allow the IconMaster to receive switching requests for events on a specific bus, there must be a corresponding entry in the bus.tbl record to map the D-MAS switching level on that bus to the IconMaster: (The switcher number field has the swr.tbl index of the
IconMaster, and the output number field is set to 1).
Table 9-3 Mapping of bus.tbl switcher Fields to D-MAS Switching Levels
bus.tbl field
Switcher number
DSK 1 switcher number
DSK 2 switcher number
DSK 3 switcher number
DSK 4 switcher number
Logo switcher number
Logo 2 switcher number
Audio over 1 switcher number
Audio over 2 switcher number
Effect switcher number
D-MAS switching level
A Audio and V – Video
D1 – Over Video 1
D2 – Over Video 4
D3 – Over Video 5
D4 – Over Video 6
L1 – Over Video 2 (aka L or Logo)
L2 – Over Video 7
O – Over Audio
O2 – Over Audio 2
E – Over Video 3 (aka Effect)
Source Configuration in src.tbl
The internal logo store of the IconMaster (associated with keyers 3-6) can be controlled as a source by D-MAS. This allows D-MAS to control which internal logo is associated with each of these keyers. If no source control is configured for a particular internal keyer, then that keyer displays whatever logo was last configured manually.
Table 9-4 Settings in src.tbl for IconMaster Internal Logo Store Sources (Keyers 3-6)
Field
Switcher number
Main source main audio input number 1
Main source main video input number 1
Source Type
Value
Index of the IconMaster entry in swr.tbl
Source type associated with a specific sub-event used to map source to a keyer (normally one of D1, D2, D3, D4,
L1 or L2). This should match the setting for corresponding “Switcher level n” entry for the keyer in swr.tbl (where n=3, 4, 5 or 6).
Machine control type
Machine control index
Default control number
Ready time
ICM
Index of the IconMaster entry in swr.tbl
11 (i.e. ready and start control)
A suitable time (a few seconds is ample)
IconMaster
Installation and Configuration Manual
125
Operation Notes
When the corresponding source entry is specified in the appropriate subevent, the corresponding material ID field accepts numeric entries between 1 and 999 to specify an internal logo from the IconMaster logo store (there is no checking to ensure a specific logo number actually exists).
At the ready time, a request is issued to load the specified logo number, unless the keyer is already active on the IconMaster’s PGM bus (in which case, the logo is not loaded until start time).
Configuration for Squeezeback and DVE Effects
The IconMaster supports up to 16 squeezebacks or DVE effects that are preconfigured (i.e.
the details of the effect can not be controlled from D-MAS). DVE transitions are not supported.
Note: Currently, only a single upstream router may be defined for the IconMaster. Thus, if an IconMaster is using explicit routing for both program and effect sources, the program and effect sources must be on the same upstream router.
The IconMaster has a dedicated DVE input; labeled “Squeeze Bkgd” on the breakout panel.
A source may be directly connected to this input, or any of several sources may be routed to it if the IconMaster is configured to use an upstream router.
Table 9-5 Settings in swr.tbl for Explicit Upstream Routing of Effect Sources
Field
1st effect input from upstream routing switcher
1st effect output on upstream routing switcher
Value
1
The output number on the upstream switcher connected to the IconMaster’s
Squeeze Bkgd input.
Describing an Effect transition in ovrtrans.tbl
IconMaster effect subevent transitions are defined by entries in ovrtrans.tbl.
Table 9-6 Effect Transition Settings for IconMaster Entries in ovrtrans.tbl
Field
Custom Transition/Effect Number
Switcher Type
Transition/Effect Name
Description
DVE Transition?
Value
Sequential, starting at 1 (not used by
D-MAS)
ICONMASTER
A name for the transition/effect. This value must be entered in the
EFFECT_TRANSITION field to initiate this effect. All transitions for the same switcher type must have unique names.
Text describing the effect (not used by
D-MAS)
N
126
Chapter 9
Automation Setup
Table 9-6 Effect Transition Settings for IconMaster Entries in ovrtrans.tbl (Continued)
Field
“Squeeze and Reveal” (R) or Stretch and Conceal (C)
Beginning DVE squeeze preset
Value
Ignored for ICONMASTER (leave blank)
The predefined IconMaster effect to perform (an index between 1 and 16 inclusive)
The transition rate to use (S, M, or F) Beginning transition or DVE squeeze duration (mm:ss:ff or S/M/F)
Horizontal wipe on beginning transition?
Ignored for ICONMASTER (leave blank)
Vertical wipe on beginning transition?
Ignored for ICONMASTER (leave blank)
Reverse wipe direction on beginning transition?
Ignored for ICONMASTER (leave blank)
Ending DVE squeeze preset
Ending transition or DVE squeeze duration (mm:ss:ff or S/M/F)
This should have the same value as the
“Beginning DVE squeeze preset” field
This should have the same value as the
“Beginning transition or DVE squeeze duration (mm:ss:ff or S/M/F)” field
Horizontal wipe on ending transition?
Ignored for ICONMASTER (leave blank)
Vertical wipe on ending transition?
Ignored for ICONMASTER (leave blank)
Ignored for ICONMASTER (leave blank) Reverse wipe direction on ending transition?
Number of transitions used in effect
Effect audio from background (on-air) or foreground (effect)
Audio transition is mix (foreground audio effects)
2
B (The
IconMaster does not support audio from effect sources)
N (although not used by the
IconMaster driver, this field may not be left blank)
Audio transition rate (foreground audio effects only)
Ignored for ICONMASTER (leave blank)
Over mix mixer (blank if not over mix) Ignored for ICONMASTER (leave blank)
Input A duck level (-100 – 0) Ignored for ICONMASTER (leave blank)
Input B over level (0 – 28) Ignored for ICONMASTER (leave blank)
Time before transition to re-route video Ignored for ICONMASTER (leave blank)
Ignored for ICONMASTER (leave blank) Time between effects for DVE transition
Delay before starting 2nd background effect source
Ignored for ICONMASTER (leave blank)
Delay before starting 3rd background effect source
Ignored for ICONMASTER (leave blank)
IconMaster
Installation and Configuration Manual
127
Configuring IconMaster to Ignore Automation Commands on Specific
Key Layers
Note: This feature is supported in IconMaster (MKE) software release 2.2 and greater.
The IconMaster is designed to operate from a single point of control. Normally, this will be either the RCP remote control panel, or by automation. The IconMaster does not support control by the RCP and automation independently at the same time. These devices can both control the IconMaster at the same time, however, and the IconMaster will operate as if the two control paths were one, using a single shared device.
To support the split use of IconMaster keyers between manual RCP operations and automation operations, the IconMaster can be setup to ignore automation commands for specific key layers. If this mode is configured, any automation commands which affect the ignored keyers will be ignored.
Setting Up
Automation
Key Masks
A key “mask” is a specific bit field in which each keyer is given a bit position, and the bit field is encoded to select which keyer layers will be respected by automation and which will be ignored.
Bit 0 of the key mask is for Keyer 1 (first external keyer)
A value of 0 allows automation to control the keyer.
A value of 1 forces automation to ignore the keyer.
Bit 1 of the key mask is for Keyer 2 (second external keyer)
Bit 2 of the key mask is for Keyer 3 (first internal logo keyer)
Bit 3 of the key mask is for Keyer 4 (second internal logo keyer)
Bit 4 of the key mask is for Keyer 5 (third internal logo keyer)
Bit 5 of the key mask is for Keyer 6 (fourth internal logo keyer)
The key mask is encoded as a byte, in the format 0xHH, where HH is the hex encoded key mask.
For example:
A key mask of 0x00 (all zeros) is the default key mask, and will allow automation control of all keyers.
A key mask of 0x0F will allow automation control of keyers 5 and 6, and will disallow automation control of keyers 1 through 4.
A key mask of 0x30 will allow automation control of keyers 1 through 4, and will disallow automation control of keyers 5 and 6.
Procedure
To set up a key mask in IconMaster, perform the following steps from a MS-Windows computer connected to the same network as your IconMaster system:
1
Open a command prompt window by selecting the <Start> button at the bottom left of the screen. Select the RUN menu item, and then type cmd in the field.
2
Press OK. A command prompt window will appear.
128
Chapter 9
Automation Setup
3
Begin a telnet session by typing telnet xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx = the IP address of the IconMaster's MKE-3901 module).
4
Type leitch as the username.
5
Type LeitchAdmin as the password.
6
To display the current automation key mask, type getAutoKeyMask, and then press
<Enter>. The hex encoded key mask will be displayed, along with the IconMaster's interpretation of the code.
For example:
-> getAutoKeyMask
Auto Key Mask:
0x30
Bit 0 - Key1: 0
Bit 1 - Key2: 0
Bit 2 - Key3: 0
Bit 3 - Key4: 0
Bit 4 - Key5: 1
Bit 5 - Key6: 1
Displays the current hex encoded key mask
Displays the status of keyer 1:
0 = keyer under automation
Displays the status of keyer 2:
0 = keyer under automation
Displays the status of keyer 3:
0 = keyer under automation
Displays the status of keyer 4:
0 = keyer under automation
Displays the status of keyer 5:
1 = keyer automation ignored
Displays the status of keyer 6:
1 = keyer automation ignored
Ignore the “value =” return line.
7
To set the current automation key mask, type setAutoKeyMask 0xHH and then press
<Enter>. (HH is the hex-encoded key mask [i.e., 0x30]. Include the 0x [zero and x] characters when entering the hex number. Again, ignore the “value =” return line.)
8
To verify the current automation key mask, type getAutoKeyMask, and then press
<Enter>.
9
To end the Telnet session, press <Ctrl> + ] (closing square bracket), and then type quit.
IconMaster
Installation and Configuration Manual
129
The following screen shows the above process, where the IconMaster begins with a key mask of 0x30 (masking/ignoring keys 5 and 6), and is changed to a key mask of 0x18
(masking/ignoring keys 4 and 5).
Figure 9-1 The getAutoKeyMask Process
Important Considerations for Automation Key Masks
The most common reason for automation key masks is to allow the manual control of some key layers, while automating the remaining key layers.
It should be noted that the IconMaster is designed for single-user operation. The “user” may be a manual operator using the RCP control panel, or it may be an automation system.
The IconMaster system does not distinguish between manual and automation users.
When a user enables a key layer for the next transition, that layer is enabled regardless of which user initiates the next transition via the TAKE button or automation TAKE command.
If a manual RCP user enables a key layer and the automation system enables a different key layer, the next TAKE will transition both keys.
The issue listed above will only be a problem if manual operations are done at the same time as automated operations. The following simple, but effective, workaround should be followed to ensure that automated TAKE and manual TAKE operations do not conflict.
All manual operations should follow these simple steps from the IconMaster’s RCP control panel.
1
Press the HOLD button to disable automation control.
2
Verify only the keyers you wish to transition manually are enabled. Normally, RCP keyer enables will follow automation control, so this step is important.
130
Chapter 9
Automation Setup
3
Press the TAKE button to perform the transition on only the selected keyers.
4
Deselect the key layers being controlled manually. This step is important, as the next automation TAKE operation will affect any keyers which are enabled for transitions.
5
Press the HOLD button to enable automation control.
Steps 1 and 5 above will safeguard against automation coming in while manual operations
are being set up and executed.
Automation Considerations
If a keyer is masked via the Automation Key Mask, the following automation commands will have no effect on the key layer:
KEY_ENABLE0x0B
KEY_MOD0x0A
LOGO_SELECT0x51
LOGO_SELECT_KEY0x71
Although the IconMaster will respond with ACKNOWLEDGE responses to these commands, the commands will be ignored by IconMaster. This has been done in order to avoid having automation systems invoke recovery procedures if they receive a NAK response.
10
Configuring IconMaster
Overview
IconMaster Configuration Utility, or ICU, software is an easy-to-use Windows®-based application for setting up and configuring the IconMaster hardware system. It allows you to control configuration of input/output functions; audio, effects, and transitions; system components; and panel components through on-screen menu selections.
IMPORTANT! You may or may not have access to the ICU software. If you do not, you must ask your system administrator to perform these operations for you.
Quick Configuration Quick Reference Chart
This chapter presupposes that you are familiar with the layout of an IconMaster control panel. If you are not, please refer to your IconMaster Functional Operation and
Configuration Manual for more information.
Note: Changes made in the IconMaster Configuration Utility will not take effect on an
IconMaster Switcher until the database has been uploaded to the IconMaster frame. See
The quick reference chart on page 193 shows the control panel clusters, the functions that
fall within each cluster, and the IconMaster configuration utility dialog box that allows you to configure that particular function.
Installing ICU Software
In order to have a fully functioning IconMaster control panel, you must use ICU to configure it. Here are the steps involved in a full installation:
131
132
Chapter 10
Configuring IconMaster
1
Check the system requirements (page 133)
2
Assemble the tools you’ll need (page 133)
3
Configure the PC display (page 135)
4
Install the IconMaster configuration utility from CD to PC (page 133)
5
Check the Ethernet connections (page 134)
6
Start the configuration utility application (page 135)
7
Adjust network settings (page 136)
8
Adjust the operating standard (page 136)
9
Adjust the system timing (page 137)
Default Configuration Files
For your convenience, several default configuration files are included on the IconMaster
SoftTools CD included with your IconMaster control panel. You can use and modify these files.
These files are set up for an SD-525i/59 bilevel sync:
Default_SD_NSM_Embedded.xml
Default_SD_NSM_Discrete2ch.xml
Default_SD_Panacea_Embedded.xml
These files are set up for an HD-1080i/59 with trilevel sync
Default_HD_NSM_Embedded.xml
Default_HD_NSM_Discrete2ch.xml
Default_HD_Panacea_Embedded.xml
These files are “getting started” databases for you to use if you do not have a router database already configured for your system:
Pana16x4 SDIAES1.da4 (Panacea 16×4, SDI video with 1 AES audio)
Pana16x4 SDIAES2.da4 (Panacea 16×4, SDI video with 2 AES audio)
Pana16x4 SDIEMB.da4 (Panacea 16×4, SDI video with embedded audio)
Pana16x8 SDI-CQ.da4 (Panacea 16×8, Clean/Quiet, SDI video with embedded audio)
Pana16x16 SDIEMB.da4 (Panacea 16×16, SDI video with embedded audio)
Plat64x64 SDIAES.da4 (Platinum 64×64, SDI video with 1 AES audio)
Plat64x64 SDIEMB.da4 (Platinum 64×64, SDI video with embedded audio)
IconMaster
Installation and Configuration Manual
133
System Requirements
The following minimum requirements are necessary to operate IconMaster configuration software.
Table 10-1 IconMaster Configuration Software System Requirements
Item
CPU
RAM
Hard disk space
Additional disk drives
Operating systems
*
Specification
266 MHz Pentium II
At least 256 MB
At least 30 MB free
CD-ROM or CD-RW
Windows® 2000, Windows XP, and
Windows Vista, with Microsoft® Internet
Explorer 5.0 or later
Port(s)
Display resolution
Ethernet
1024×768, high color (16 bit) or higher
Pointing device Mouse, trackball, touch screen, or other pointing device
*
Windows 2000, Windows XP, Windows Vista, and Microsoft Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Tools You
Will Need
Icon Series SoftTools CD (P/N 178-000176-00)
PC matching system requirements
Installing the IconMaster Configuration Utility
1
If an existing version of the IconMaster configuration utility is installed on the PC, uninstall it, and then restart the PC.
2
Close all other applications running on the PC and insert the Installation CD into the PC
CD-ROM drive.
3
Double click Setup.exe if setup does not start automatically.
4
When the Welcome box appears, click Next.
5
When the Warning! box appears, click Next.
6
Accept the software license.
If you do not accept the license, installation will not continue.
7
If the Microsoft .NET framework box appears, follow the instructions, and then click Next.
8
When the Select Installation Type box appears, follow the onscreen instructions to install all four software applications (Content Editor, LogoCreator, IconLogo SoftPanel, and
IconMaster Configuration Utility).
134
Chapter 10
Configuring IconMaster
Figure 10-1 Selecting or Deselecting a Feature
9
When the Setup Complete message appears, click Finish.
Removing IconMaster Configuration Software
To remove IconMaster Configuration software:
1
Go to the Windows Control Panel (Start
Settings Control Panel), and then select
Add/Remove Programs.
2
Select IconTools from the list.
3
Select Remove and follow the instructions provided on-screen.
CAUTION
Removing IconTools will also remove LogoCreator, Content Editor, and
IconLogo SoftPanel.
Ethernet
Connections
IconMaster uses Ethernet-based communication. Default IP addresses will function correctly in a “one frame and one control panel” configuration if they are both connected to the same switch that is not connected to a network server/router.
IconMaster
Installation and Configuration Manual
135
Figure 10-2 Simple Non-Network IconMaster Configuration
Starting
ICU
To start the ICU application, select the IconMaster Configuration Utility icon by following this path:
Start
Programs Imagine Communications IconTools IconMaster
The IconMaster configuration software main menu will display. The main window of the
IconMaster configuration software provides a list of the main menu item groups. The groups that appear depend on whether you select frame configuration or panel configuration.
Configuring a PC Monitor for Best Display
For IconMaster software to show clearly and appropriately on a PC monitor:
1
Set the Display Properties for the monitor to 1024×768 pixel resolution (or larger) with regular or small fonts.
2
Go to the Start menu, and then select Settings
Control Panel Display Display
Properties
Settings.
3
Set the color palette to display either High (16-bit) or True (24-bit) color.
Frame Configuration Menu Groups
When you choose to create a new IconMaster Frame Configuration (File > New >
IconMaster Frame Configuration), four menu groups will appear. They are described in the following sections:
136
Chapter 10
Configuring IconMaster
Panel Menu
Group
When you choose to make a new Control Panel Configuration (File > New > Control Panel
Configuration), one menu group will appear. For information on this menu group, see
Initializing IconMaster
Once you have started the IconMaster configuration utility, you will need to make adjustments to the following settings:
Network settings
Operating standard
System timing
Network
Settings
The default IP address will function correctly in a “one frame and one panel” configuration if both frame and panel are connected to the same switch that is not connected to a network server or router. However, if you are connected to a network server or router, you will need to coordinate the IP address for the MKE-3901 module, the MGI-390x module, and/or the IconMaster control panel.
Notice that there are two different network settings selections within the main menu groups. One selection controls network settings for the frame (found in the System
Configuration menu group), and the other selection controls the network settings for the control panel (found in the Panel Configuration menu group).
If you have changed the IP address on the card edge of the MKE-3901 module, you must
make the same change in the Network dialog box (see page 176 for more information on
changing this setting).
To change the network settings of the IconMaster control panel, access the Panel Network
Configuration dialog box (see page 185 for more information on changing this setting).
Operating
Standard
The default operating standard for IconMaster is SD525 (270Mbit/sec). To change the
operating standard, access the Genlock and Standard (see page 168 for more information
on changing this setting).
Note: When changing between HD operating standards (for example, from 1080I to 720P), you must repower the IconMaster.
IconMaster
Installation and Configuration Manual
137
System
Timing
Changing the system timing causes the IconMaster system to adjust the horizontal and vertical phase of the reference input so that the most number of inputs have their vertical timing value at zero. To make changes to the IconMaster timing, access the Genlock and
Standard dialog box (see page 168) to make changes to the IconMaster timing.
CAUTION
Do not do a system timing activity until the IconMaster has been downloaded with a valid configuration file with appropriately assigned primary inputs.
Unwanted on air operation may result.
Managing ICU Databases
Note: Instructions on enabling a router database for use with an IconMaster system begin
ICU uses XML databases to store configuration information about the different IconMaster setups you develop.
CAUTION
If you do not want your changes to appear in the active XML database, you should create a new XML database file before you make any changes.
You can create an ICU database from scratch or create one by opening an existing database, renaming it, and then manipulating existing information.
Creating an ICU Configuration File
1
Start IconMaster, as explained on page 135.
2
At the IconMaster Configuration Utility main menu window, select File
New. The New
Configuration dialog box will appear.
Figure 10-3 New Configuration Dialog Box
138
Chapter 10
Configuring IconMaster
3
Select the appropriate radio button to set up the type of configuration file you want to create.
Table 10-2 New Configuration Types
Configuration
IconMaster Frame
Configuration
Description
Specific configuration of inputs and outputs; transition, audio and effect buttons; machine control (including GPI/
GPO); genlock; router management; automation; license management; serial port; and multiviewers
Control Panel Configuration Specific configuration and panel network configuration functions for ICONM-RCP (12-button hardware panel)
Control Panel Configuration
(RCP-16)
Specific configuration and panel network configuration functions for (16-button hardware panel)
4
Depending on which selection you made in step 3, the applicable menu options will appear.
5
Click File
Save As, and then enter a name for the new database.
6
Click Save. This will become the currently active database, and its name will be displayed in the Title bar at the top of the ICU main menu window. Database files are saved in the
Documents and Settings
All Users Application Data Imagine
Communications
IconMaster directory on your local drive.
Opening an Existing ICU Configuration File
Database files are saved in the Documents and Settings
All Users Application
Data
Imagine Communications IconMaster directory on your local drive.
CAUTION
ICU for IconMaster 3.1 has been tested for backwards compatibility with Iconmaster 1.5.3 and IConmaster 2.X configuration databases.
However, re-verify all configuration settings before applying them to the IconMaster.
It is strongly recommended that you back up your old configuration file before using a new 3.1 configuration file.
1
Start IconMaster, as explained on page 135.
2
At the IconMaster Configuration Utility main menu window, select File
Open. The
Open A Configuration dialog box will appear.
3
Select a configuration file (XML file) from the displayed list. If the XML file resides in a different location, use standard Windows navigation techniques to move to the location of the file you want to display.
4
Highlight the name of the file you want, and then click Open.
Saving
Databases
Saving to a New Database
1
From the menu bar, click File, and then select Save As. The Save As dialog box will appear.
2
In the File Name drop-down list box, do either of the following:
Enter a name for the database that will hold the changes you just made.
IconMaster
Installation and Configuration Manual
139
Highlight the name of an existing database (use standard Windows navigation procedures to select a location different from the default location). Be careful doing
this.
Saving to an existing database will cause the software to overwrite the original database settings. It will not append your new changes to the existing database.
3
Click Save.
4
(Optional) Upload the effects to the IconMaster frame. See
on page 139 for more information.
Uploading
Databases
Changes made in an ICU dialog box will not take effect until the saved database has been uploaded to the IconMaster frame. To upload changes:
1
Save your current configuration file.
2
From the menu bar, click Send CFG to frame. An information message will prompt you to confirm the upload of the configuration to the IconMaster frame.
3
Click Yes. The database will be uploaded to the IconMaster frame.
Most new settings will take effect on the IconMaster immediately. Changes that require a reboot include:
Standard change (also requires new firmware)
Upgrade license from IconMaster LITE to full IconMaster
A change of serial port settings
Changing an SD system from 8-channel audio operation to 16-channel audio operation
Input/Output Group Settings
The Input/Output group on the left side of the IconMaster configuration software screen includes the following dialog boxes: Primary Inputs, Audio Configuration, Audio Over
Matrix, and Aux Bus.
Figure 10-4 Input/Output Menu Group
This menu group controls system input and output configuration functions, as shown in
Figure 10-4
.
140
Chapter 10
Configuring IconMaster
Primary Input Settings
Figure 10-5 Primary Input Dialog Box
Using the Primary Input settings, you can perform the following actions:
Change the names of your sources
Manage router sources at the physical control panel (instead of always having to download a configuration from the ICU)
Change the router source number
Choose a preset quick select
Enable Program Bypass
Protect or unprotect the router A/B feeds to IconMaster
1
To change the Name of the input source, double-click the name in the cell, and then enter the new name. The length of the name is limited to 10 characters (including spaces), over 2 lines, with a maximum of 5 characters per line.
1
The Protected option allows a router destination to be locked to prevent inadvertent changes to the
A/B sources feeding the IconMaster. With the Protected feature enabled, only the IconMaster will be able to change the router destination at will, but other users will be prevented from changing that destination until the Protect is removed. The X-Y bus panel ID setting on the Router Configuration page must be set to a unique value.
IconMaster
Installation and Configuration Manual
141
To allow control panel router source management, click the Dynamic check box to the right of the router source number. If you have selected “12 inputs” as the primary input mode, you will be able to allow control of 12 sources. if you have selected “22 inputs” as the primary input mode, you can allow control of 22 sources. To set the primary input
mode, you must use the System Configuration dialog box. See page 172 for instructions.
The Preset QS (Quick Select) assigns the sources you pre-configured in the Quick Select
Dialog Box (see page 155) to a primary input. To choose a preset quick select, click the
Preset QS drop-down list box that corresponds to the appropriate router source number, and then scroll down to the appropriate quick select number. Use of preset Quick Selects is not recommended if the Auto Take function of Quick Selects is enabled.
Note: The PGM Bypass option is not available on a system that does not include an
IconMaster breakout module.
To enable the PGM Bypass option, click the check box to the right of the PGM Bypass Input
Bus selection.
When the PGM Bypass option is selected, IconMaster can control an auxiliary output from the primary router (the router output for bypass will be a separate output with the same content as the IconMaster PGM output for this to operate correctly). This auxiliary output will follow the same source that is currently on-air. The router output can be linked to the
IconMaster’s emergency PGM input and, in the event of an IconMaster failure or loss of power, a bypass relay will instantly connect the auxiliary signal to the IconMaster’s PGM output BNC.
To protect router A/B feeds to IconMaster, click the Yes - Protected radio button. To
unprotect the feeds, click the No - Not Protected radio button.
To prevent operators from protecting a Destination and then not being able to find the panel that originated the protect, Imagine Communications’s physical router control panels incorporate an override feature. To override a Destination Protect that was set by
another panel or IconMaster, press and hold the control panel Protect key until it stops blinking (about 5 seconds). At the end of the 5-second period the Destination Protect key will no longer be lit, which means that the destination is no longer protected. For more information about this feature, see the pertinent router control panel installation, configuration, and operation manual.
Place a check beside Send Audio level to router for embed system if you want to route the embedded audio with the associated video. Otherwise, leave it blank.
This option will route up to four audio levels as assigned on this page. If all audio levels are required to be routed as defined in the Navigator routing database editor then go to the Router
Configuration page and select Switch all Audio in Database for Embedders.
Audio Configuration Settings
Using the Audio Configuration dialog box in ICU, you can designate the audio output for each audio input.
142
Chapter 10
Configuring IconMaster
Define audio profiles
Assign audio profiles
Figure 10-6 Audio Configuration Dialog Box
Note: The Audio Channel 8 Channels and 16 Channels selections are not available if the
IconMaster has been configured for HD operation.
Audio Profiles
To simplify configuration of inputs with similar audio settings and correct wiring or mapping problems, IconMaster provides one default and 15 user-definable audio profiles. An audio profile is a set of audio input to output mappings, which can be applied to any input source.
In the Audio Routing Setup, all inputs are assigned the Default profile.
Profiles that have a check in the Enable column are available for assignment.
To edit a profile:
1
Select one of the user-defined profiles at the top of this screen.
2
(Optional) Click in the Audio Profile field and type a new name to rename the profile.
3
Select the primary audio input type. Options are:
IconMaster
Installation and Configuration Manual
143
Embedded audio is recovered from the specific SDI input.
In an SD IconMaster system, as in
Figure 10-6
, under Audio Channel, you can determine whether to use 8 or 16 audio channels. Then, for each primary audio input, each of the 8 or 16 audio input channels can be assigned to any or all of the 8 or 16 audio output channels.
NOTE: If the audio configuration for an SD Iconmaster is changed from 8 channel to 16
channels, or from 16 channels to 8 channels, you must reboot IconMaster to ensure that all audio channels are properly configured. After uploading the configuration file to the IconMaster, you can reboot the MKE using ICU's Reboot MKE button.
In an HD IconMaster system with embedded audio, as in
Figure 10-7
, for each primary audio input, each of the 16 audio input channels can be assigned to any or all of the 16 audio outputs.
Figure 10-7 Audio Dialog Box — HD with Embedded Audio
Discrete audio is available with the optional MKA-3901 audio module only. Discrete audio inputs are sample rate converted, and thus can only accept PCM audio.
NOTE: Due to sample rate converters, Dolby-E inputs via discrete audio are not
supported by IconMaster.
In a HD IconMaster system with discrete audio, as in
Figure 10-8
, for each primary audio input, each of the 8 audio input channels can be assigned to any or all of the 16 audio outputs.
144
Chapter 10
Configuring IconMaster
Figure 10-8 Audio Dialog Box — HD with Discrete Audio
If discrete audio inputs are used, all Audio Input Type settings should be manually assigned to either Processed or Unprocessed. The Automatic setting is not applicable to discrete audio inputs.
4
Under Audio Channel, select either 8 or 16 channels.
As the audio configuration state changes from 8 to 16 (or vice versa), the Audio Over Matrix
and Audio Cluster dialog boxes will also change accordingly. See page 146 and page 160
for more information.
5
Edit the Audio I/O Mapping grid.
This audio mapping will only be applied to the specified input.
IconMaster can recover up to 16 audio channels from each of the 12
1 or 22
2 primary embedded inputs. Alternatively, if the MKA-3901 module is present, IconMaster allows for up to 4 AES inputs from each of the 12 or 22 primary inputs. Each of the AES inputs has 2 audio channels for a total of 8 audio channels for each input.
6
To rename an audio input, in the Audio I/O Mapping grid, double-click on the name of the input, and then enter a new name.
A maximum of 6 characters is allowed.
7
Under Audio Input Type, for each AES audio input select one of the following:
Processed (default)—Full audio control is enabled. IconMaster ignores incoming C and
V bits (see
Table 10-3
), and full audio control is enabled. Operators have full control of audio gain, channel swapping, sum, mono, etc. The output AES channel status (C and
V) bits are forced to indicate valid PCM audio.
1
This is true for 12 input mode.
2
This is true for 22 input mode.
IconMaster
Installation and Configuration Manual
145
Unprocessed —Audio is passed without modification (all audio settings are ignored).
This is the required setting to pass non-PCM audio, such as Dolby
®
E encoder/ decoder
1 and Dolby
®
AC-3, through IconMaster.
Full audio control is disabled. No gain or channel manipulation is allowed. The output
AES channel status (C and V) bits follow the incoming channel status bits.
Automatic —IconMaster monitors the incoming C & V channel status bits. If the incoming channel status bits indicate Valid PCM (C=0, V=0), then full audio control is enabled. If either channel status bit is set to 1, audio control is disabled. The output AES channel status bits (C and V bits) follow the incoming channel status bits.
Table 10-3 AES Channel Status Bits
Bit Function
indicates whether the AES channel contains VALID data.
0
Each AES channel pair includes two important channel status bits:
C Indicates whether the AES channel contains PCM sampled audio data
PCM audio, which can generally be gain adjusted, summed, swapped, mixed to mono, etc.
V Valid data
1
NON-PCM data, which should not be altered in any way.
Invalid data
0
1
The following outlines some common data types, and their C & V bit settings:
C bit V bit Meaning Typical Use
0
0
0
1
Valid PCM
Valid Non-PCM
Invalid PCM
Normal audio
Dolby-E, data carried as audio
1 1 Invalid Non-PCM
Audio with error (CRC, equipment, etc), which should NOT be converted to analog via D/A process.
Rarely seen
When changing the assignment from Processed to Unprocessed, all audio settings will return to their default values. When changing the assignment from Unprocessed to
Processed, all audio settings will be restored to the values currently set on the control panel.
Note: Audio profiles are assigned using ICU and can be dynamically assigned using ISCP,
ISCP-Lite or the RCP.
1
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
146
Chapter 10
Configuring IconMaster
Audio Over Matrix Settings
Figure 10-9 Audio Over Matrix Dialog Box
The Audio Over Matrix dialog box includes the settings for the Audio Over inputs 1 and 2.
Using this dialog box, you can assign the A/O inputs to the audio outputs and configure audio ducking.
IconMaster has 2 AES inputs dedicated to the audio overs. Each AES input has 2 audio channels. The number of outputs corresponds to the number of audio channels selected at
the Audio Configuration dialog box (see page 141). In an SD system, each of the 4 channels
can be assigned to any or all of the 8 or 16 Audio Outputs (depending on how SD audio is
configured. See page 146). In an HD system, each of the 4 channels can be assigned to any
or all of the 16 Audio Outputs.To change the assignment, select the check box that corresponds to the input/output combination required.
An audio output cannot be assigned to more than 1 audio input. An audio input can be assigned to more than 1 audio output.
The audio assignments can be different for A/O1 and A/O2.
As shown in
Figure 10-9
, audio over channels 1, 2, 3, and 4 are defaulted to Audio
Outputs 1, 2, 3, and 4, respectively.
Audio over ducking can be configured differently for A/O1 and A/O2.
IconMaster
Installation and Configuration Manual
147
If Duck All Audio Output Channels is selected, any audio output that is not assigned an audio input will “fade down” the background audio on that channel during an audio over.
If Duck Only Output Channels with A/O Assigned is selected, only the audio outputs that are assigned an audio input will “fade down” the background audio and perform the audio over.
Note: Logo audio matrix settings are configured in the IconLogo soft gui tool. See the
“Audio Menu Page” section of your IconLogo documentation for more information.
Aux Bus (Auxiliary Bus Configuration) Settings
The Auxiliary Bus Configuration dialog box (
Figure 10-10
) configures the IconMaster auxiliary bus routing. This makes it possible to control additional router destinations with the Aux bus. The IconMaster control panel provides for the selection of 1 of 12 Aux buses.
Figure 10-10 Auxiliary Bus Configuration Dialog Box
Any destinations can be used for the Aux buses.
Configuring Aux Buses in Static Mode
When not in Router Database mode (see page 170), follow these steps to configure the Aux
Buses:
1
Select one of the Aux buses listed (1 through 12) from the Aux Bus drop-down list box.
The name associated with that Aux bus item will appear in the Aux Name box.
To change the name(s) of the Aux bus configurations, double-click in the Aux Name box, and then enter a new name for the aux bus (a maximum of 6 characters is allowed).
148
Chapter 10
Configuring IconMaster
After the changes have been uploaded to the IconMaster frame, this name will appear in the LCD button that is on the extreme right side of the Aux bus. (See your Iconmaster
Functional Operation and Configuration Manual for the LCD button location.) If multiple
Aux bus ports are assigned individual names (e.g., Aux 1 is renamed Aux A, Aux 2 is renamed AuxCtrl), you can toggle the Aux bus LCD button to scroll through the various buses. Any Aux buses labeled “Unused” will not appear on the LCD button display.
2
if it is not already selected, click the Enable checkbox.
Any aux buses that are not enabled will not appear in the LCD button display on the RCP, and will be grayed out in the ISCP.
The router source levels will be set automatically, to the defaults in
Figure 10-10
.
3
To change the name of a router source configuration, click on the appropriate name box, and then enter a new name for the associated source (a maximum of 8 characters is allowed).
4
To change the level assigned to each Aux bus, click on the appropriate level box, and then choose the required level from the drop-down box. There is a maximum of 16 levels (0 to
15). Selecting Unused will disable an Aux bus from use.
5
The number in the Dest column should be set to the router destination being used for each of the Aux buses. To change the assignment, double-click on the Dest field to be changed, and then enter the new assignment. Press Enter to complete the change.
Any router input can be assigned to any of the 12 Aux bus sources (labeled Src 1 to Src 12).
This is possible for each aux bus independently. To change the assignment, double-click the
Src field to be changed, and then enter the new assignment. Press Enter to complete the change.
Note: It is strongly encouraged that any Aux busses that are not in use be disabled using the Enable checkbox at the top of each Aux bus page, for Aux busses 1–12.
Configuring Aux Buses in Router Database Mode
To configure the Aux buses using an external router in Router Database mode (see
page 170 for information), the Aux Bus dialog box will appear slightly different, as in
Figure 10-11
.
Figure 10-11 Aux Bus in Router Database Mode
IconMaster
Installation and Configuration Manual
149
To configure the Aux Bus in Router Database mode, follow the first three steps above, and then continue as follows:
1
For each input number, in the Router Levels row at the top of the grid, pick a level.
2
Pick a destination for that router source from the DEST row at the bottom of the grid.
3
In the Source Input grid, click a field to open a menu, and then click on an item in the router database.
The field updates with the destination information for that cross-point.
Repeat these steps as necessary to complete the grid. All unused fields in the grid should be set to Unused.
When you select a source that is not in the database, all the sources will be listed. However, these sources will not have cross-points. To enter the cross-point, click Manual, and then type in the cross-point.
The label does not represent the cross-point. It is just there as a reminder.
Functional Group Settings
The Functional group on the left side of the IconMaster configuration software screen includes the following dialog boxes: Transition, Effects, Quick Select, Audio Cluster, and
Keyer.
Figure 10-12 Functional Menu Group
This menu group controls the functional configuration of the IconMaster, as shown in
Figure 10-12
.
150
Chapter 10
Configuring IconMaster
Transition
Settings
Figure 10-13 Transitions Dialog Box
Setting Transition Rates
Unless otherwise stated, the range is from 1to 300 frames.
Table 10-4 Transition Settings
Transition type
Video Frame Rate
Silent Transition rate
Fade to Black (FTB)
Transition Rate
Description/Option
Slow
Medium
Fast
Cut (range from 0 to 300 frames)
Fades out the audio at a faster rate than the video transition, to eliminate a distracting segue during the audio transition
“Dissolves” a video picture to black
Default
30 frames
16 frames
8 frames
1 frame
10 frames
10 frames
Silence to follow FTB is normally used for transitions. With this option selected, the “fade to silence” during the video fade to black occurs at the rate you have set in the FTB
Transition Rate. To enable this transition, select the Silence to Follow FTB check box on the Transitions window. The default value is disabled (unchecked).
Setting Audio Transition Types
Note: The manual use of a cut button always overrides the selection on the Transition function bus.
The Audio Transition Type can be either V-Fade or Follow Video. Choose the appropriate radio button for your selection, as follows:
Effects
Settings
IconMaster
Installation and Configuration Manual
151
Choose the default V-Fade selection to fade the first source to silence, and then fade up the new source. During this operation, the “V” button on the Transition Functions bus is half-illuminated.
Choose the Follow Video option to have the audio transition type always follow the video transition type automatically.
Preventing and Enabling Closed Captioning
Select the VBI (vertical blanking interval) Closed Caption check box to prevent closed captioning on line 21 in 525 from being squeezed during an effect.
If the Closed Caption check box is not selected, the default value is line 20.
Figure 10-14 Effects Dialog Box
Using the Effects dialog box in ICU, you can perform the following actions:
Create an Effect
Edit an Effect name
Disable and/or re-enable an Effect
Reset an Effect
Set a second channel for preview operations
Select a channel to edit
Change a background source
Change a crop size
Change the position of a channel
Change the squeeze ratio of a channel
152
Chapter 10
Configuring IconMaster
Preloaded Effects in Default Configuration Files
For your convenience, several default configuration files are included on the IconMaster
SoftTools CD included with your IconMaster. These configuration files include the following preconfigured effects:
Effect 1 = SQ-BRT, 1chl 35% window in upper right, with external background
Effect 2 = SQ-BLT, 1chl 35% window in upper left, with external background
Effect 3 = SQ-R, 1chl 75% H, 100%V on right side, with external background
Effect 4 = SQ-L, 1chl 75% H, 100%V on left side, with preset background
Effect 5 = SQ-URT, 1ch 75% L-Bar window in upper right with preset background
Effect 6 = SQ-ULT, 1ch 75% L-Bar window in upper left with preset background
See page 132 for a list of files that are included.
Before You Begin
Before you begin, ensure that you observe the following:
Each effect should be viewed as a sequence of events, like a filmstrip.
Each effect must be defined horizontally and vertically (the default position of 0,0 is defined as the upper left corner of the screen).
All effects start with the Program full size. This is defined as Start A.
Note: For both single channel and 2 channel effects, the sequence will end with either
Program as the only full size on-screen image.
For a single channel effect, do not select the Dual Channel Effect check box.
Segment 1 defines the position and size at the end of the first transition.
There is an entry only for Program.
The background may be External Background or Preset.
The end of the effect is set by Program.
For a single channel effect, the effect must end as a full-size Program or Preset.
For a 2-channel effect, select the Dual Channel Effect check box.
Segment 1 defines the position and size at the end of the first transition.
There is an entry for both Program and Preset.
The background may be External Background or Preset.
The end of the effect is set by End A and End B.
The effect must end as one of these options:
A full-size Program and a zero size Preset
A full-size Program and a full-size Preset fully on screen.
If you Preview Effect on PST in your effect, you can choose to preview the effect before you send it to air. If you select Dual Channel Effect, you cannot preview the effect before you send it to air.
Up to 16 different effects can be set up.
For an effect in SD, there may be potential discrepancies in horizontal and vertical blanking between analog and digital systems. It is recommended that a crop be added to the effect setup. IconMaster includes the following default values for the crop settings:
Left 2
IconMaster
Installation and Configuration Manual
153
Right 2
Top 1
Bottom 1
These default values prevent the appearance of a black border when the effect is underway.
Creating an Effect
An effect is made up of a sequence of events or segments. To create and store additional segments in your effect, click Add. Then, with the new segment number selected in the
Segments field, you can modify what the effect looks like for that segment.
To create and store a multi-segment effect:
1
Double-click one of the cells in the Effects column, and then optionally, rename the effect
(a maximum of 6 characters is allowed).
2
Select Segment 1 in the Segments field for the effect being edited. When a segment is highlighted in the Segments field, the squeeze and crop fields are enabled.
3
Select Enable Crop, and then make your required numeric settings (0 to 100) for Top,
Bottom, Left and Right.
4
Set the destination of your Squeeze effect in the first segment by changing the percentage numbers in the Ratio and Position columns.
(Select Maintain Aspect Ratio if you need the horizontal and vertical values to be kept at a constant ratio.)
Note: Positions can be negative, for off screen positions above or to the left of the viewable screen area.
5
Click Add to create Segment 2 of your effect, and then select new values for Ratio and
Position.
6
Continue for segments 3 and 4 as applicable.
Up to 4 segments are available for each effect.
The Reset button deletes all of the settings for the effect being edited. When you select the
Reset button, a pop-up confirmation window appears, verifying that you want to reset the manual effect.
Editing an Effect Name
1
Under the Name column in the Effects box, double-click on the name of the effect you want to change.
2
Enter a new name for the effect (a maximum of 6 characters is allowed).
Enabling an Effect
Click the empty check box to the left of the name of the effect you want to enable. As a result, the Enabled check box will have a check mark in it to indicate the selected effect is enabled.
154
Chapter 10
Configuring IconMaster
Disabling an Effect
Click the check box to the left of the name of the effect you want to disable. As a result, the
Enabled check box will appear empty to indicate the selected effect is disabled.
Resetting an Effect
1
Highlight the effect you want to reset.
2
Click the Reset button at the bottom of the Enabled/name columns. An information message will “ask” if you want to reset the selected effect.
3
Click Yes. The effect will be reset to its default value.
Setting the Second Channel for Preview Operations
To use the second channel of the effects engine to preview effects on the Preset video
output, select the Preview Effect on PST check box. The Background Source will be forced to External Background and cannot be changed. In addition, the Preview will apply to all 16 effects.
The second channel can only be used in 1 mode; in other words, Dual Channel Effect in the Channel section and Preview Effect on PST are mutually exclusive.
Selecting a Channel to Edit (Adding a Second Channel to an
Effect to Squeeze the PGM and PST Video)
To add a second channel to an effect to squeeze the PGM and PST video, select the Dual
Channel Effect check box, select the Preset radio button, and then follow the procedure as described above. You can edit the effect after you have created it, by first selecting the appropriate channels box.
Changing a Background Source
Note: If Preview Effect on PST is selected, you will not be able to select a background source.
For each effect, the background source can be changed through the pull-down
Background Source box.
For a single channel effect, your choices are
Preset
External Background
For a 2-channel effect, when neither channel is full size, the Background Source will be forced to External Background and cannot be changed.
Changing a Crop Size
1
In the Crop box, check the Enable Crop check box. The Left, Right, Top, and Bottom spin boxes will be enabled.
2
Enter the new percentage for each crop value. The range of values ranges from 0 to 100%.
IconMaster
Installation and Configuration Manual
155
Starting and Ending With a Background Transition
Place a check in the box to start or end with a background transition.
Changing the Position of a Channel
1
Select the appropriate segment in the Segments field for the effect being edited. When a segment is highlighted in the Segments field, the Position spin box is enabled.
1
Under the Squeeze
Position box, click the H (horizontal) or V (vertical) position box.
1
2
Enter the new percentage for the position value. The range of values ranges from -100% to
+100%.
Changing the Squeeze Ratio of a Channel
1
Select the appropriate segment in the Segments field for the effect being edited. When a segment is highlighted in the Segments field, the Ratio spin box is enabled.
2
Unclick the Maintain Aspect Ratio check box.
3
Under the Squeeze
Ratio box, click the H (horizontal) and/or V (vertical) box, and then enter a new ratio value(s). The range of values ranges from 0% to +100%. You can see a thumbnail view of the ratio of the squeeze on the Effects dialog box.
4
Under the Squeeze
Position box, click the H (horizontal) and/or V (vertical) box, and then enter a new position value(s). The range of values ranges from -100% to +100%. You can see a thumbnail view of the position of the squeeze on the Effects dialog box.
Creating L-Bars
1
Select the appropriate segment in the Segments field for the effect being edited.
When a segment is highlighted in the Segments field, the Ratio spin box is enabled.
2
Under the Squeeze
Ratio box, click the H (horizontal) and/or V (vertical) box, and then enter a new ratio value(s).
The range of values ranges from 0% to +100%. Setting the H value to 0 will set the L-bars to appear at the top left corner of the display. You can see a thumbnail view of the ratio of the squeeze on the Effects dialog box.
Creating Wipes
1
Select the appropriate segment in the Segments field for the effect being edited.
When a segment is highlighted in the Segments field, the Ratio spin box is enabled.
2
Under the Squeeze
Position box, click the H (horizontal) box, and then enter a position value of 100.
This value will cause a wipe effect on screen.
Quick Select
Settings
Quick Select recalls the stored appearance of either the PST or the PGM monitor.
A Quick Select is a snapshot of the state of the various portions of your system. The Quick
Select dialog box has four tabs which allow you to select combinations of the following items:
1
Position values always refer to the full, uncropped size.
156
Chapter 10
Configuring IconMaster
Both external keys
Both audio overs
Logo Key 3 through Logo Key 6 states and/or contents (not available with IconMaster
Lite license)
Aux bus functions
Transition functions
To configure a Quick Select:
1
Choose whether you will recall the PST state or the PGM state.
Regardless of which state you will recall, the complete set of data is stored.
Recall Saved PST State: Recalls whatever is on the Preset monitor at the time that the
Quick Select is made
Recall Saved PGM State: Recalls whatever is on the Program monitor at the time when the Quick Select is made
The PST/PGM state selection is a global selection that is made for all Quick Selects.
2
Go through the four tabs of the Quick Selects dialog box, making selections for Quick
Selects 1-8. Each row in the table represents a single Quick Select.
The contents of these tabs are described in the following sections.
Quick Selects for External Keys
Quick Selects for Internal Logo Keys
By default, all options on these tabs are selected, except for the Auto Take option on the
Transitions tab.
3
When you are satisfied with your Quick Selects choices, save and upload to your IconMaster frame.
Back at your Control Panel, after the revised ICU file has been uploaded, when you store and recall Quick Selects, the snapshots that are captured will reflect the settings made on these screens.
Quick Selects for External Keys
The External Keys tab of the Quick Select Configuration dialog box has options for recalling both the visual and audio portions of the two external keyers.
IconMaster
Installation and Configuration Manual
157
Figure 10-15 External Keys Quick Select Dialog Box
When you enable External Keys selections, you recall the state of the settings assigned to the keyer at the time the quick select was saved. You can enable or disable selected keyers, which will remove those keyer functions from the corresponding quick select.
When there is a check mark for Ext Key 1 and Ext Key 2 for a Quick Select, that quick select will store and recall the visual conditions of that keyer, including its transparency, screen location, etc.
When there is a check mark for Ext A/O 1 and Ext A/O 2 for a Quick Select, that quick select will store and recall those external audio overs.
Click Select All to select both external logo keys and both audio overs on that Quick Select.
Click Select All again to unselect all components of both external logo keys and both audio overs for that Quick Select (row).
Quick Selects for Internal Logo Keys
Each of the four internal logo keys can have its state and/or its content saved as part of a
Quick Select.
Note: If you have an IconMaster Lite license key, options for Internal Keys will be unavailable.
158
Chapter 10
Configuring IconMaster
Figure 10-16 Logo Keys Quick Select Dialog Box
For Logo Keys 3- 6, you can choose to store the state and/or content as part of the Quick
Select. Selecting the Select All box will store state and content for all keyers for that quick select.
Table 10-5 Settings for Each Internal Keyer
Keyer Setting
Keyer (3 - 6) state
Keyer (3 - 6) content
Function
Whether the keyer is on or off
The Logo #, Transparency, processing, etc. that are applied to that internal keyer
Select All will select all internal logos for that quick select. Each of the check boxes in the quick select row indicated whether the function listed at the top of the dialog box will be recalled during that quick select operation.
If you select the Allow On-air Changes to Keyers check box, when the data stored in this
Quick Select is recalled, the keyers will be updated on the PGM monitor. If this check box is not selected, Then when the Quick Select is recalled, the contents of the keys that are currently on the PGM monitor will not change. This will not change the state of the keys, though, and the keys can still come off air. This setting is a global setting that applies to all
Quick Selects, for example to protect station branding.
Quick Selects for Aux Buses
For each Quick Select, you can choose to recall the contents of any or all of the 12 Aux buses.
Note: To avoid excess router switching traffic during a quick select recall, deselect all unnecessary Aux busses in quick selects that are in use.
IconMaster
Installation and Configuration Manual
159
Figure 10-17 Aux Bus Keys Quick Select Dialog Box
Click Select All to select all the Aux Buses for that particular Quick Select. Click Select All again to unselect all the Aux Buses.
Quick Selects for Transitions
The Transition tab of the Quick Select Configuration dialog box lists various components of a transition.
Figure 10-18 Transitions Quick Select Dialog Box
160
Chapter 10
Configuring IconMaster
By selecting a Transition check box, you recall the state of the transition settings, as described in
Table 10-6
.
Table 10-6 Quick Selects Options for Transitions
Quick Select Option
Background Transition
Background Source
Effects
Transition Rate
Transition Type
Saves and recalls the state of the BKGD button on the control panel
The source that is on the Preset bus (whether the background is on or off)
All effects that are set on the transition
The preset duration for transitions
The shape of the transition
Click Select All to enable all transition features for that quick select. Click Select All again to unselect all transition features for that Quick Select.
If Auto Take is selected, when the Quick Select is recalled to the PST, and a take is activated to send the PST content to the PGM. The previously shown PST content is not preserved. If
Auto Take is not selected, you can achieve the same effect by pressing Take on the Control
Panel.
Note: A breakaway transition cannot be saved in a Quick Select.
Audio Cluster Settings
Figure 10-19 Audio Cluster Dialog Box
1
An Audio Cluster is a group of audio channels whose gain can be adjusted as a group. A cluster can have up to 16 audio channels. The number of outputs corresponds to the
number of audio channels selected at the Audio Configuration dialog box (see page 141).
Typically, a cluster is a grouping of similar audio channels, such as MAIN+SAP or SURROUND
(6 channels).
1
This dialog box is for use with the optional IconMaster audio control panel.
IconMaster
Installation and Configuration Manual
161
In the Audio Cluster dialog box, you can setup up to 8 audio clusters by selecting the audio channels you wish to group together. A specific audio channel can appear in more than one cluster. (For example, in
Figure 10-19
audio channels 3 and 4 appear in Clust2; audio channels 7 and 8 appear in Clust4.) The cluster name can be edited by selecting the name field, and then typing a new name.
The default setting is for an audio cluster to be the same as an AES audio channel pair. This means cluster 1 is AES channel pair 1, cluster 2 is AES channel pair 2, etc.
Audio Cluster gain is adjusted directly from the IconMaster RCP control panel’s optional audio control panel.
Keyer
Settings
The Keyer dialog box allows you to give a name to the external keyers. These names are displayed on the keyer LCD displays of the RCP control panel.
Figure 10-20 Keyer Dialog Box
Changing a Keyer Input Source Name
To change the Name of the input source, double-click the name in the cell, and then enter a new name. The length of the name is limited to 10 characters (including spaces), over 2 lines, with a maximum of 5 characters per line.
Control Group Settings
The Control group on the left side of the IconMaster configuration software screen includes the following dialog boxes: Machine Control and GPI-GPO.
Figure 10-21 Control Menu Group
This menu group controls the machine control and GPI-GPO configuration functions, as shown in
Figure 10-21
.
162
Chapter 10
Configuring IconMaster
Machine Control Settings
The Machine Control dialog box allows you to set the appropriate control functions for automation.
Figure 10-22 Machine Control Dialog Box
Using the Machine Control functions, you can perform the following actions:
Coordinate GPI/GPO and machine control events
Select the automation type
Select the machine control settings
Temporarily disable selected machine control settings
The Source column indicates the selected source. This column is read-only; you cannot make changes here.
The Name column indicates the selected sources’ name. This column is read-only; you cannot make changes here.
Configuring GPI/GPO Events to Machine Control
If you configure GPI or GPO events to machine control, you must ensure both GPI/GPO and
Machine Control settings are set up correctly. See
Figure 10-23
for the coordinating
GPI-GPO and Machine Control settings.
IconMaster
Installation and Configuration Manual
163
Note: GPOs and GPIs can use the external interfaces. When using an external interface, 48 additional GPOs and 48 additional GPIs are available.
Figure 10-23 Coordinating Machine Control and GPI/GPO Settings
Selecting Automation Types
The Type column indicates if the input you have selected (1 through 12) will trigger GPOs
(GPI Outputs), Serial protocol, or—through the Disabled option— normal functionality of the selecting source. The GPO configuration is common for all input types. If you have selected a GPO that is already configured in the GPI-GPO dialog box, a message will warn you that this action will affect the settings of your previously configured GPO.
The GPO option offers sources 1 to 13 and the Serial offers device IDs 0 to 31. When
Serial is selected, the Device ID value becomes the same for all functions.
Selecting Machine Control Settings
If you have selected GPO or Serial as automation type, the Machine Control columns (Play,
Stop, Cue, Mark, Blank, Rewind, and Fast Forward) are enabled, and you may select values from the drop-down list boxes.
Disabling Machine Control Settings
Select the Disabled check box to temporarily disable any Machine Control settings you have made. (This is the default setting for the Automation Type.)
164
Chapter 10
Configuring IconMaster
Preroll Functions
Using the Preroll functions, you can perform the following actions:
Enable the preroll status
Set or reset the preroll duration
Enabling Preroll Status
The Enabled check box enables the preroll status for that output. If you select Enabled, but have Disabled selected under Type, no action will occur.
Setting/Resetting Preroll Duration
The Preroll Duration (Frames) sets the duration of the preroll from 0 to 600 frames. The default value is 60.
To make all of the preroll times match the preroll time of the selected item, press Set All
Durations Equal to Current Record’s Duration.
Note: If dynamic router control is selected for the Primary Input, then Machine Control is not allowed for that input.
IconMaster
Installation and Configuration Manual
165
GPI Settings
To use external GPIs, you must first enable them on the ICU Network page (see page 176),
and configure the JLCooper eBOX (see their documentation for details).
Note: If configuring an IconMaster LITE, fewer GPI and GPO selections are available.
IconMaster LITE has 8 GPI and 7 GPO.
Figure 10-24 GPI Settings Dialog Box
Using the GPI dialog box, you can perform the following actions:
Add or delete a General Purpose Interface input (GPI)
Assign a trigger to a GPI source (GPI sources are assignable to Quick Selects, Bus selections, and different transition types and rates)
Coordinate GPI and machine control events
Specify polarity of the GPI
Set up the trigger function
Choose what interface the GPI comes from
The operational polarity for open and closed settings varies depending on the source of your GPI triggers.
When using an Internal GPI from the IconMaster breakout box, if the polarity is set to open/edge, when the defined GPI is closed, the function is triggered. If the polarity is set to close/edge and the defined GPI is opened, the function is triggered.
When using an eBOX GPI (represented in
as an ExtGPI in the GPI
Number column), if the polarity is set to open/edge, the defined GPI is opened from closed, the function is triggered. When the polarity is set to close/edge and the defined
GPI is closed, the function is triggered.
Adding a GPI
To add a GPI:
166
Chapter 10
Configuring IconMaster
1
Click Add GPI at the bottom of the GPI dialog box.
A new row appears in the GPI table.
2
Click the GPI Number field to open a drop-down menu, and then choose a GPO.
3
Click the Assignment field to open a drop-down menu, and then choose one of the many possible triggers.
Table 10-7 GPI Assignment Options
Options
Disabled
PST input (1 - 12)
Audio Trans
Take Button
FTB Button
AO to Air
Key (1 - 6) Button
Quick Select (1 - 8) Button
PGM input (1 - 12)
Video Trans
Preroll Button
FTS Button
Key to Air
BKGD Button
A/O (1 - 2) Button
Automation Hold
Any changes you make to each GPO Assignment drop-down menu automatically are reflected in the GPO drop-down box in the Keyer dialog box.
Note: Key to Air and AO to Air allow a keyer or Audio Over to be active on air as long as the GPI is active. These are recommended for use with EAS systems, where the EAS alert system can drive a GPI on the IconMaster to enable the Audio Over content coming from the EAS system.
4
Type a source in the SRC field.
5
In the Polarity column, set the GPO to Open or Closed.
6
Set the trigger function to Edge or Level.
The examples below provide a scenario where a GPI source is used to select between 2 assignments (A and B), and when using an eBOX as the trigger source:
If Open polarity is used for the Level option:
When the Polarity = Closed (not set) and Trigger = Level, select source A.
When the Polarity = Open (set) and Trigger = Level, select source B.
If Open polarity is used for the Edge option:
When the polarity changes from Closed to Open and Trigger = Edge, switch from source A to source B. Nothing happens when the polarity changes back from Open to Closed.
When the polarity changes again from Closed to Open and Trigger = Edge, switch from source B to source A. Nothing happens when the polarity changes back from
Open to Closed.
Deleting a GPI
To delete a GPI, highlight the entry you want to remove, and then click the Delete GPI button.
IconMaster
Installation and Configuration Manual
167
GPO Settings
To use external GPOs, you must first enable them on the ICU Network page (see page 176),
and configure the JLCooper eBOX (see their documentation for details).
Figure 10-25 GPO Settings Dialog Box
Using the GPO (GPI out) dialog box, you can perform the following actions:
Add or delete a General Purpose Interface output (GPO)
Name a GPO
Assign a trigger to a GPO source
Specify the polarity
Set the duration
Setting Operation Precedence
If an IconMaster GPO is assigned on the GPO page of ICU, it will take precedence over the
GPO operations if the same GPO is assigned to an RCP soft LCD button. In this case, the
RCP soft LCD button will have no effect. Thus, if you wish to assign a GPO to an RCP soft
LCD button, the GPO’s setting on the GPI-GPO page of ICU should be set to Disabled.
Adding a GPO
To add a GPO:
1
Click Add GPO at the bottom of the GPO dialog box.
A new row appears in the GPO table.
2
Click the GPO Number field to open a drop-down menu, and then choose a GPO.
3
Enter a logical name in the Name column.
This name will be shown on the RCP panel, remind operators what the GPO will do.
4
Click the Assignment field to open a drop-down menu, and then choose one of the many possible triggers.
Any changes you make to each GPO Assignment drop-down menu automatically are reflected in the GPO drop-down box in the Keyer dialog box.
168
Chapter 10
Configuring IconMaster
5
Click the SRC field to open a drop-down menu, and then choose a source.
6
In the Polarity column, set the GPO to Open or Closed.
7
In the Duration column, type the duration of the GPO.
The maximum duration is 900 ms. To have the GPO stay on, leave the Duration cell empty or set it to 0.
If you configure GPO events to machine control, on the Machine Control dialog box, you must ensure that machine control is enabled for that GPO is enabled under the Type column, and that Preroll is Enabled for sources that have a GPO trigger assigned. See
page 162 for more information.
Deleting a GPO
To delete a GPO, highlight the row you want to remove, and then click Delete GPO.
System Config Group Settings
The System Config group on the left side of the IconMaster configuration software screen includes the following dialog boxes: Genlock and Standard, Router Configuration, System
Config, Automation Config, Network, License Management, Serial Port, Multiviewer, Clock and Timer, and Logging Server.
Figure 10-26 System Configuration Menu Group
This menu group controls the genlock/standard, router, system, automation, network, license management, serial port, clock and timer, and multiviewer configuration functions, as shown in
Figure 10-26
.
Genlock and
Standard
Settings
The Genlock and Standard dialog is a very specific function dialog box. Using this box, you can perform the following actions:
Select an operating standard
Select a genlock source type
Set the timing for the IconMaster system
Get the timing report for the IconMaster system
IconMaster
Installation and Configuration Manual
169
Figure 10-27 Genlock Dialog Box
Selecting an Operating Standard
To select an operating standard, select the required standard from the Operation
Standards pull-down menu.
Note: When changing between HD operating standards (for example, from 1080I to 720P), you must repower the IconMaster.
Selecting a Genlock Source Type
Select either Composite or Tri-Level from the Genlock Source Type pull-down menu. The default Genlock Source Type is Composite.
Adjusting the IconMaster System Timing
Note: Do not initiate a timing setup until all source inputs and destinations have been assigned in the primary inputs page, the appropriate configuration file has been applied to the IconMaster, and all input signals are applied and stable.
1
Press the Set Auto-Timing Operation button, and then click Yes after confirming all keyers are in an off-air state.
170
Chapter 10
Configuring IconMaster
This action causes the IconMaster system to adjust the horizontal and vertical phase of the reference input so that the most number of inputs have their vertical timing value at zero.
The results of this function are not displayed in the Timing Results area. Ensure that the external keys are taken off-air before you run the Set Timing procedure.
2
Allow the Timing operation to run for 1 minute.
3
Press the Get Auto-Timing Results button to retrieve the new timing reading from the
IconMaster.
Note: The system phase values let you know how much the reference input had to be delayed so that the video inputs would be within a 1 video line of the reference input.
The Get Timing results are not a real-time indication of each input's timing offset. If an input's timing has changed, you must activate Set Timing again to retrieve the current results.
These results will be displayed in the Timing Results area. If external keys are on air when the Timing operation is initiated, the Timing results will show an error message, indicating that the timing setup was not run, and that the external keys must be taken off-air before
Set Timing is run again.
4
Adjust the V phase timing for any source that is reported as not timed.
For example, if, after executing the Set Timing and Get Timing commands, you read a V phase value that equals 50, reduce the V phase timing of that input source by 50 lines.
5
Repeat steps 1 to 4 after adjusting the V phases of the sources, until all of the V phase values for the inputs are zero (i.e., the system is fully timed).
Router Configuration Settings
Figure 10-28 Router Configuration Dialog Box
IconMaster
Installation and Configuration Manual
171
The Routing Configuration dialog box (
Figure 10-28
) is used to set up the type of router which IconMaster uses as its primary source router.
Router Mode
If the IconMaster is configured with NSM type NEO module routers, select the Internal
(NSM) Router setting. If any type of external router is used (Panacea, Integrator,
Platinum, or third party), select External Router.
External Router
Choose either of the following:
Select Serial Port if you have a serial connection between the IconMaster and the router.
Select Ethernet if you have an Ethernet connection between the IconMaster and the router. When you choose this option, the selections for a router name and the
IP addresses for primary and secondary controllers will become available.
If Ethernet is selected, serial port E is automatically released, and a pop up appears from ICU.
In circumstances when you have primary and secondary router addresses configured, failover will take place.
Router Database
If the IconMaster is configured with static inputs (router sources are assigned to
IconMaster inputs, without the operator ability to change the router assignments), then do not use the Router Database settings. However, if you wish to use the dynamic routing features of IconMaster, or to use an existing router database to select your
IconMaster sources (regardless of Dynamic Routing use), select the Using Routing
Database checkbox.
Selecting Sorted will optionally sort the router database alphanumerically.
If Using Routing Database is selected, you will need to create a router database and then send this database to the IconMaster through the Navigator application.
You cannot use the native RouterMapper DA4 database; you must convert it into
an XML format through CCS Navigator™. See page 199 for detailed instructions.
Switch All Audio in Database for Embedders allows a configuration to switch up to
15 levels of audio as defined in the router configuration of an imported Navigator router database.
Set the value in the Router Transition Delay spin box as appropriate for your router.
The router transition delay can be a value between 1 and 15. For Platinum routers, typically a value of “5” is required. With most other routers, the default setting of “1” will suffice. Assessment of the performance of your channel release system should be performed to ensure that the router transition delay meets your station’s requirements.
172
Chapter 10
Configuring IconMaster
System Configuration Settings
The 22 Inputs option is grayed out because
“External Router” is set to No on the
Router Configuration
Figure 10-29 System Configuration Dialog Box
The System Configuration dialog box includes settings for various IconMaster system parameters, each of which is detailed below.
Processing Priority
The Processing Priority settings affect how the IconMaster routes internal video and audio signals. Use the drop-down boxes in the A/V Path group to change Keyer priority settings and assign the FX priority.
The IconMaster has a separate Clean output which can be assigned as well. The video and audio pick positions for the Clean output can be set in the Processing Priority settings.
If the Disable FX checkbox is checked, the IconMaster FX squeezeback effects engine will be disabled.
Primary Input Mode
This setting affects whether 12 or 22 primary inputs are available to IconMaster.
If 12 Inputs is selected, the 12 primary source input buttons will select between all available input sources.
If 22 Inputs is selected, the primary source buttons will be split into one group of inputs numbered 1 – 11, and another group numbered 12 – 22. The far right primary source button will be used as the SHIFT button. When set to 22 Inputs mode, the
SHIFT button toggles between 1 – 11 and 12 – 22.
These modes are only available on ICONM-RCP devices, not on ICONM-RCP16.
Note: It is strongly suggested that you retime the IconMaster system if you change from 12 to 22 input mode. This will ensure the additional 10 inputs are correctly timed into
IconMaster. See page 168 for information on setting the timing for an IconMaster system.
IconMaster
Installation and Configuration Manual
173
Fast Reset Behavior
Note: Fast Reset is not available on ICONM-RCP16 control panels.
This setting allows you to quickly reset audio gain and/or PROC parameter settings for an IconMaster input source, internal or external keyer, Audio Over, or audio control item on the Audio Control Panel.
There are three separate operations that are enabled when the Fast Reset function is selected: SET, CLEAR, and RECALL. If the SET function is enabled, the parameter will not be reset, but its current value will be saved as the source’s user-saved reset value.
This is the value that will be used during a RECALL operation. If the CLEAR function is enabled, the user-saved reset value will be cleared (back to factory value), and the keyer’s parameters will also be reset back to this factory value. If the RECALL function is enabled, the user-saved reset value set up through a SET operation will be applied.
Reset values can be either a factory reset values (0 dB gain, and default keyer values), or can be user-saved reset values, which are saved on a source-by-source basis for audio gains and on a keyer-by-keyer basis for keyer settings.
If Audio Gain + Proc is selected, the IconMaster will reset the audio gains of the selected source or audio configuration item to unity. It also resets all PROC audio input parameters to their original default values.
If Audio Gain is selected, the IconMaster will reset the audio gains of the selected source or audio configuration item to unity, but it will not reset any of the PROC audio input parameters.
When fast resetting a keyer, all keyer parameters will be reset to their defaults.
When fast resetting an Audio Over, the Audio Over mix ratio will be reset to 50/50.
Take Button
This setting affects the system behavior when the TAKE button is pressed during a transition.
VANC Data in FTB
This setting affects whether the PGM output includes VANC data from the PGM input source when the system is in the Fade to Black mode.
PGM Bus Hot-Punch
This setting defines what the IconMaster will do when a PGM bus source is hot-punched. By default, the IconMaster will drop all keys, audio overs, and all effects.
By un-checking these settings, the IconMaster can be configured to retain the on-air keys, audio overs, and effects in progress.
EAS Audio
These settings affect how IconMaster responds to EAS (Emergency Alert System) triggers received.
If set to None, no audio will be altered during an EAS event.
If set to On Audio Over 1 or On Audio Over 2, the selected audio over keyer will be turned ON during an EAS event, and turned OFF when the event completes. The
Ratio setting adjusts the A/O ratio for the selected AO keyer during the EAS event.
Note: Use of On Audio Over 1 or On Audio Over 2 as part of an EAS event may result in an undesired on-air operation if the EAS receiver terminates the EAS message to the
IconMaster before the completion of the EAS audio message. Consider using a GPO from the EAS receiver, connected to a GPI using the Key Enable GPI function to maintain an active Audio Over while the EAS receiver is transmitting the EAS audio message.
174
Chapter 10
Configuring IconMaster
Audio Over Ratio Behavior
This setting allows you to specify the way the audio over ratio is interpreted by
IconMaster. The default value for Audio Over ratio is 50%, which means full level mix for both AO and PGM. The 50% or 100% mix also applies to Logo Audio Overs.
If 50% Mix is selected as a mode of operation, at 50% ratio the Audio Over and
PGM audio each make up 50% of the mix, and the level of each will be -3 dB.
Figure 10-30 Audio Over Ratio in 50% Mix Mode
If 100% Mix is selected as a mode of operation, at 50% ratio the mix will be
100% of Audio Over and 100% of PGM, and will decrease respectively as you move “left” or “right” of the 50% mark.
Figure 10-31 Audio Over Ratio in 100% Mix Mode
Automation Configuration Settings
IconMaster
Installation and Configuration Manual
175
Figure 10-32 Automation Configuration Dialog Box
The Automation Configuration dialog box allows you to choose between logical
IconMaster inputs or physical router inputs.
When you select Logical IconMaster Inputs, the Automation system will only be able to switch PST and PGM bus inputs that have been assigned (through the Primary Input dialog box) to inputs 1 to 12 or 1 to 22 (depending on your configuration).
When you select Physical Router Inputs, you can switch unassigned sources directly from a router to any four IconMaster PST and PGM bus inputs ranging from 1 to 12 (or 1 to 22) that you will select from the Dynamic Inputs to Use drop down list boxes. When you select an input, IconMaster will check to see if that particular input has been assigned already to any of the PGM or PST bus buttons. If not, it will assign your source the to first, or top left, drop-down input box, which corresponds to inputs 1-12 (or 1-22) on the PGM or
PST bus.
Currently, Asynchronous Status Reporting and Automation Log are not supported.
If you want the automation system to change sources even while under hold, place a check beside Update while in hold.
176
Chapter 10
Configuring IconMaster
Network Settings
Figure 10-33 Network Dialog Box
The Network dialog box contains the network address settings that are necessary for the
ICU program to communicate with the IconMaster’s MKE-3901 module, and for the
MKE-3901 to communicate with IconMaster’s RCP control panels. It also contains selections for external interface devices (such as the JLCooper Electronics eBOX® Quad Serial to
Ethernet Interface
1
) and their corresponding network address settings.
You can rename each frame that contains IconMaster components by clicking in the
Iconmaster Channel Name field, and then typing the new name. A maximum of 8 characters is allowed for a host name.
The default network IP address of the IconMaster’s MKE-3901 module is 192.168.100.252.
If this address has not been changed on the MKE-3901 module, then this setting should not be changed.
If you have changed the IP address of the MKE-3901 using the module’s card-edge display, enter the new IP address in the IP Address field.
If you are communicating correctly with the MKE-3901 module, and wish to change the IP address using the ICU software, select the New IP Address checkbox, and then enter a new IP address in the field to the right. The Subnet Mask and Gateway settings can also be set in this way.
Note that after changing the MKE-3901 module’s IP address, you will need to power cycle the IconMaster's MKE-3901 module, and put the new address into the IP
Address field above.
You can connect to two external input/output devices through the boxes labeled External
IO 1 and External IO 2.
1 eBOX is a trademark of JLCooper Electronics.
IconMaster
Installation and Configuration Manual
177
1
Select the Enable External IO Module checkbox, and then select the external device type from the drop-down list box.
2
In the corresponding list boxes, enter an IP address and a port number for the external device.
3
(Optional) Enable the External IO Admin Password checkbox, and then enter the appropriate system administrator pasword.
If the External IO 1 or External IO2 is enabled, additional GPO and GPI functions will
become available in the GPO and GPI pages on page 165 and page 167.
See the JLCooper instruction manual for information on configuring the eBOX for use with
IconMaster.
License Management Settings
The License Management dialog box contains information about license keys installed on your IconMaster systems.
Figure 10-34 License Management Dialog Box
The following licenses are available for Iconmaster:
ICONL-UPG: This licence option enables the INTERNAL keyers functionality of the
Iconmaster, if an MGI3902 or MGI3903 board is installed.
ICONM-CEN: This licence enables Iconmaster to integrate with multiviewers. See
Multiviewer Configuration Settings
ICONM-CLS: If this license is enabled and you have a Magellan Logging Server purchased separately), IconMaster can be configured to send standarrdized operational logs to the server. See
information.
To add a license key:
1
In the License Management dialog box, click Get License.
The IconMaster Serial Number field updates. If a license key is currently installed on the
MKE-3901 board, the License Key field also updates.
2
Provide the IconMaster serial number to your Customer Service representative.
There are two ways to provide the serial number and receive your license key:
By phone: Contact your Sales representative.
178
Chapter 10
Configuring IconMaster
By faxing or mailing a form to Imagine Communications: This form is available by clicking License Form. The form includes information on where it should be sent.
(Acrobat Reader is required.)
3
Enter the provided key in the License Key field.
Your license should be recognized immediately. You must restart the IconMaster frame when the system is converted from IconMaster Lite to IconMaster.
Serial Port Configuration Settings
Note: The JL Cooper external interfaces include configuration options for RS232 or RS422 operation, and are configured on the external interface, not within ICU.
Figure 10-35 Serial Port Configuration Dialog Box
The IconMaster currently supports several serial port direct connections; however, you can expand the number of available serial ports with the ICONM-BO-V video breakout module
(described in
ICONM-BO-V Video Breakout Module
on page 32) or an external interface
device such as the JLCooper eBOX. The Serial Port Configuration dialog box allows you to reassign the serial ports’ functions. If the Serial port baud rate, bits, parity or stop bits are changed, the IconMaster will require a restart.
Figure 10-36 ICONM-BO-V Serial Ports
Note: Because of real-time response considerations, certain functions will always be assigned to ICONM-BO-V serial ports C and D. You cannot change the functions for these ports.
IconMaster
Installation and Configuration Manual
179
To change the serial port function of serial port A, B, or E on the ICONM-BO-V breakout module, highlight the name of the breakout module’s serial port you want to configure, and then select a function from the Option drop-down list box.
Note: In previous releases of IconMaster Configuration Utility, serial port A could be configured for Automation, Multiviewer, or Machine Control. With release 3.2.1, only
Machine Control is allowed.
To change the serial port function on a port on the external interface device, highlight the name of the external interface port, and then select a option from the drop-down list box.
You must restart IconMaster if you change Serial port baud rate, bits, parity, or stop bits.
Note: To ensure proper functionality, you should verify the IconMaster hardware configuration for RS-422 or RS-232 for use of internal serial ports.
RS-232 pinouts are different between Port A and Ports B and E. See
on page 32 for wiring details.
Multiviewer Configuration Settings
To use a compatible Imagine Communications multiviewer (HView SX Hybrid or PredatorII) with IconMaster, a valid license is required. See
on page 177 for more information. If controlling a third party multiviewer via TSL protocol
version 3.1, then a multiviewer license is not required.
IconMaster supports the following multiviewers:
HView SX Hybrid (previously CENTRIO)
PredatorII
Third party multiviewers via TSL protocol version 3.1 (choose “other” as device type)
180
Chapter 10
Configuring IconMaster
Figure 10-37 Multiviewer Configuration Settings Dialog Box
For each multiviewer display the IconMaster will be controlling, create a profile which defines the multiviewer system, display output, and (optionally) the layout to display. Within the layout, you can define the PIP and UMD numbers that correspond to the IconMaster inputs (sources) and also the IconMaster outputs.
Table 10-8 Multiviewer Profiles Table in Multiviewers Configuration
Item
Enabled
Device Type
Always Active
Profile Name
Description
Activates playout from IconMaster to this multiviewer
Select one of the following:
HView SX Hybrid (CENTRIO)
Predator II
Other
If selected, this profile will become the active profile, if no other profile is currently controlling the selected multiviewer display endpoint (multiviewer IP address and display number)
File name of the profile to be called
IconMaster
Installation and Configuration Manual
181
Table 10-8 Multiviewer Profiles Table in Multiviewers Configuration
Item Description
Connection Type Options are based on the device type selection, and can include Ethernet and serial
HView SX Hybrid (CENTRIO) only supports Ethernet connection
Other (device type option) only supports serial connection
UMD Refresh
Interval
Delete
Determines the rate at which IconMaster will poll, measured in seconds
Clears the contents of the row, and contents of other associated tables (
and
)
For each row in the Multiviewers Profiles table, you can also configure other data, as displayed in
Table 10-9 Other Data Table in Multiviewers Configuration
Item
Connection
Destination
Port
Display
Layout Name
Description
For HView SX Hybrid, the IP address of the Ethernet connector on the hardware device
The comm port the multiviewer connects through (leave blank if the multiviewer does not use a port)
The display number (ID) to control (value between 1 and 4) corresponding to the physical multiviewer Display output DVI
1/2 or HD_SDI 1–4)
The name of the layout to be loaded (If the layout name is blank, the multiviewer will not be commanded to change layouts, thus leaving the existing layout on-screen; PIPs and
UMDs will still be refreshed)
For each row in the Multiviewers Profile table, you can also configure PIP and UMD data, as displayed in
Table 10-10 PIP & UMD Table in Multiviewers Configuration
Item
Input
PIP
UMD
Description
These items are defined in your multiviewer profile.
For each of PGM, PST, Clean, and every input source, enter the PiP associated with the text label that will be the recipient of the UMD data.
For each of PGM, PST, Clean, and every input source, enter the UMD address for that item.
These settings activate under monitor text labels and tally lights using a serial tally protocol.
As a result, UMD text labels and serial tally indicators will be enabled on a multiviewer output device such as SuiteView.
Normally this will indicate, for example, the PIP on a video wall that is currently on the PGM monitor, PST Monitor, and/or Clean monitor.
IconMaster supports TSL protocol version 3.1.
182
Chapter 10
Configuring IconMaster
Clock and
Timer
For the clock and timer to be available, a button needs to be defined for each. See
Figure 10-38 Clock and Timer Settings Dialog Box
The Clock and Timer dialog box includes settings for IconMaster's real-time clock and segment timer functions, each of which is detailed in
.
Table 10-11 Clock and Timer Settings Options
Item Description
CLOCK Enable Enables IconMaster to synchronize its internal real-time clock with an external clock source.
IconMaster uses the SNTP protocol across Ethernet to query an NTP time server.
CLOCK Source Enter the IP address of an NTP time server, as well as a time zone offset. NTP time server provides UTC time, and requires the client (IconMaster) to provide a local time offset. By default, IconMaster will re-sync its clock every 60 minutes. This can be changed by editing the
Re-Sync Interval field.
If using IconMaster's RCP as the clock source, the RCP must be connected to an external LTC timecode time-of-day source. Enter the RCP's IP address as the SNTP Server IP Address. In this status, the local time offset (Time Zone) setting will be ignored by IconMaster.
NOTE:
IconMaster does not maintain its real-time clock when power cycled. The NTP server (or
RCP) must always be available when IconMaster powers up and during operations.
Press the CLOCK button on IconMaster's RCP to Re-Sync IconMaster's clock with the NTP server.
The DST Start and End time should be identically set to 02:00. One hour will be automatically adjusted from the 02:00.
IconMaster
Installation and Configuration Manual
183
Table 10-11 Clock and Timer Settings Options
Item
Daylight Savings
Time
Description
IconMaster can automatically adjust for daylight savings time, if configured. If configuring a custom DST adjustment window, IconMaster will add one hour between the start and end times defined.
NOTE: if configuring a custom DST window, the dates may need to be changed annually.
If using IconMaster's RCP as the clock source, settings will be ignored by IconMaster, so just select Disable DST.
CLOCK Display IconMaster can display the clock in either 12h or 24h formats. When configured for 12h format, IconMaster can display AM/PM indicators. The Frame Count can also be optionally displayed.
TIMER Enable Enables IconMaster's segment timer functionality. When enabled, IconMaster will reset the segment timer to zero on each transition of the BKGD source.
Reset Timer There are two options: FX and Keyer/AO. Check one or both of these options, and
IconMaster will reset the segment timer on each FX transition and/or all keyer (video and
Audio Over) transition.
Clock and Timer are managed by the MKE card(s). They are not local to an RCP but they can change depending on what MKE the RCP is connected to. If the LTC output of a RCP is set to track the timer, it will NOT reset at a segment end if the panel is not connected.
The clock display of an RCP connected to a MKE that has never synced up with an NTP server will be --:--:--.--.
The text on the clock will be inverted if an RCP connected to a MKE has failed to resync with NTP server. In this situation, the MKE is free running (relying on its own clock).
The LTC output is only available on the HRCP RoHS compliant version of the HRCP (855T
RCP). The LTC output on the RCP is frame drop in 29.9, no frame drop in 25.
184
Chapter 10
Configuring IconMaster
Logging Server Configuration
For the logging server to be available, you need a license. See
on page 177. For information on Logging Server installation and operation, and
sample logs, see
Figure 10-39 Logging Configuration Dialog Box
Enter the IP address of the logging server.
When the bandwidth limit is set to 0 (default), there is no limit to the volume of messages sent. If you enter another number in this field (measured in kbytes per second) that is now much data will be sent. A message backlog will be created, and messages will be sent when there is bandwidth available.
The dwell-time value determines how often a range control such as a fader bar, knob, or slider will send feedback to the logging server.
Along the left side of the Filters table are listed various sources that can provide data to the
Logging Server. Place checks beside the areas of the interface that you would like to send items to the logging server.
The various system log message severities are listed across the top of the Filters table. When you select a source, severity levels for that source become available for selection. Check or uncheck severity levels to determine the types of information that will be sent to the logging server. For more information, see
Interpreting IconMaster Messages in the
Panels Group Settings
The Panel configuration menu group appears when you have selected “Control Panel
Configuration” as your type of configuration.
IconMaster
Installation and Configuration Manual
185
Figure 10-40 Panel Menu Group
This menu group controls the panel-specific configuration and panel network configuration functions, as shown in
Figure 10-40
. The functions controlled by this item group are described in the following sections.
Note: When uploading a new panel configuration, the control panel will disconnect from any IconMaster channel currently under control, and will automatically connect to Channel
1. Similarly, all Primary and Secondary channel groups will be disconnected, and must be re-established.
Panel Network Configuration Settings
Note: See
on page 191 for information on how to complete the Master
Assignment section of this screen when in Group mode.
Figure 10-41 Panel Network Configuration Dialog Box
186
Chapter 10
Configuring IconMaster
The Panel Network Configuration dialog box contains the network address settings that are necessary for the IconMaster control panels to communicate with the IconMaster
MKE-3901 modules.
To change or set the name of the IconMaster control panel (up to 8 characters in length), click in the Control Panel Host Name field, and then type the new name. The factory default for the IconMaster control panel is 192.168.100.251, and will be shown in the
Control Panel IP Address field.
To change the IP address of the IconMaster control panel, select the New IP Address check box, and then enter the new IconMaster Control Panel IP Address.
To change the Subnet Mask, enter the new IP address in the Subnet field.
To change the Gateway IP address, enter the new IP address in the Gateway field.
When you are not in Group mode, the Master Assignment section of the dialog box allows you to enter the names and IP addresses of up to 8 MKE-3901 modules that the
IconMaster control panel can communicate with. To change or set the name of an
IconMaster MKE-3901 module, click in the Host Name field, and then type the new name, up to a maximum of 8 characters.
Similarly, to change or set the address of the IconMaster MKE-3901 module, click in the IP
Address field, and then type in the new IP address.
If you have configured the IconMasters to interface with multiviewers, you can assign up to three profiles to be automatically recalled and controlled when the RCP connects to the
IconMaster. These profiles are setup and named for each IconMaster individually. See
page 179 to configure the profiles.
When the RCP connects to the given IconMaster, it will recall the profile defined in the
Multiviewer Profile 1 Name field. Optionally, the operator may choose to recall profiles 2 and 3 at connect time, and may change to these display profiles anytime during operations.
If a Profile Name field is blank, no profile operations will be initiated by connecting an RCP to the IconMaster. If no multiviewer profiles are configured on the RCP, but “Always Active” profiles are enabled on the IconMaster MKE-3901 module, the MKE-3901 will continue to maintain an active connection to the “Always Active” multiviewers, providing PiP, UMD, and layout updates as necessary.
Button Configuration Settings
Using the Button Configuration dialog box, you can assign specific functions to the configurable clusters and to the transition cluster on the IconMaster main control panel.
Depending on whether your control panel is model ICONM-RCP or ICONM-RCP16, you will have different options.
IconMaster
Installation and Configuration Manual
187
ICONM-RCP
Configurable cluster
Configurable cluster
Transition cluster
Figure 10-42 Button Configuration Dialog Box - ICONM-RCP
The available functions for each group of buttons are shown in
Table 10-12
.
Note: Always ensure that channel buttons are allocated left to right, with Channel 1 on the left most button of Cluster 1.
Table 10-12 Button Clusters, Functions, and Selections
Button Group
Cluster 1 and Cluster 2
Function
Frame Select
Selections
CH 1, CH 2, CH 3, CH 4, CH 5, CH
6, CH 7
GPO Output control GPO1, GPO2, GPO3, GPO4, GPO5,
GPO6, GPO7, GPO8, GPO9, GPO10,
GPO11, GPO12, GPO13
Quick Selects QS 1, QS 2, QS 3, QS 4, QS 5, QS 6,
QS 7, QS 8
Fast Reset
(cluster 2)
Clocks & Timers
Fade to Silence
Fade to Black
SET, CLEAR, RECALL (appear in
Parameter Adjustment Control cluster)
TIMER, CLOCK
SIL
FTB
188
Chapter 10
Configuring IconMaster
Table 10-12 Button Clusters, Functions, and Selections (Continued)
Button Group
Transition Cluster
Function
Transition Rates
Breakaway
Automation Hold
Effects
Fade Types
Machine Control
None
Selections
SLOW, MED, FAST, CUT
AUDIO, VIDEO
HOLD
FX
FXI (effects inhibit automation ignore)
TAKEFADE, FADETAKE, FADEFADE,
CROSSFADE
CUE, FF, MARK, PLAY, REW, STOP
None
Note: Changing any of the Transition Cluster functions will require the replacement of the text film on the corresponding IconMaster control panel button. See the IconMaster
Operation and Configuration Manual for more information.
To assign a function to a button, click the graphical button in the dialog box. A pop up window will display a graphical image of the current function assigned to the button, as well as a drop-down menu. The drop-down menu will list the available functions that can be assigned to the selected button. Select the new function from the drop down menu then click OK to accept the change, or Cancel to exit.
The newly assigned function name will appear on the graphical button. Each function can only be assigned to 1 button at a time. If the drop-down menu does not list the function you want to assign, either the function is not available for that button, or the function is already assigned to another button.
Note: Frame Select buttons must be assigned starting with the far left button on Cluster 1.
IconMaster
Installation and Configuration Manual
189
ICONM-RCP16
Configurable cluster 1
Configurable cluster 2
Transition cluster
Figure 10-43 Button Configuration Dialog Box - ICONM-RCP16
The available functions for each group of buttons are shown in
Table 10-12
.
Note: Always ensure that channel buttons are allocated left to right, with Channel 1 on the left most button of Cluster 1.
Table 10-13 Button Clusters, Functions, and Selections
Button Group
Cluster 1 and Cluster 2
Function
Frame Select
GPO Output control GPO1, GPO2, GPO3, GPO4, GPO5,
GPO6, GPO7, GPO8, GPO9, GPO10,
GPO11, GPO12, GPO13
Quick Selects QS 1, QS 2, QS 3, QS 4, QS 5, QS 6,
QS 7, QS 8
Clocks & Timers
Fade to Silence
Fade to Black
Internal Key
(cluster 2)
Selections
CH 1, CH 2, CH 3, CH 4, CH 5, CH
6, CH 7
TIMER, CLOCK
SIL
FTB
KEY3 - KEY6
190
Chapter 10
Configuring IconMaster
Table 10-13 Button Clusters, Functions, and Selections (Continued)
Button Group
Transition Cluster
Function
Transition Rates
Breakaway
Automation Hold
Effects
Fade Types
Machine Control
None
BKGD
PANEL-LOCK
Trans/Hotkey
Selections
SLOW, MED, FAST, CUT
AUDIO, VIDEO
HOLD
FX
FXI (effects inhibit automation ignore)
TAKEFADE, FADETAKE, FADEFADE,
CROSSFADE
CUE, FF, MARK, PLAY, REW, STOP
None
Transition
Hotkey
Note: Changing any of the Transition Cluster functions will require the replacement of the text film on the corresponding IconMaster control panel button. See the IconMaster
Operation and Configuration Manual for more information.
To assign a function to a button, click the graphical button in the dialog box. A pop up window will display a graphical image of the current function assigned to the button, as well as a drop-down menu. The drop-down menu will list the available functions that can be assigned to the selected button. Select the new function from the drop down menu then click OK to accept the change, or Cancel to exit.
The newly assigned function name will appear on the graphical button. Each function can only be assigned to 1 button at a time. If the drop-down menu does not list the function you want to assign, either the function is not available for that button, or the function is already assigned to another button.
Frame Select buttons must be assigned starting with the far left button on Cluster 1.
LTC Configuration
Figure 10-44 LTC Configuration Dialog Box
IconMaster
Installation and Configuration Manual
191
To configure your LTC output, choose the source you want the output to follow, which can be either Timer or Clock.
MKE Group
Without additional configuration, IconMaster hardware can connect to up to eight
MKE-3901 modules in master/slave configurations. You can add more MKE-3901 modules on the MKE Group dialog box.
Figure 10-45 MKE Group Dialog Box
Click Enable to include the hierarchy of channels and groups in the configuration file when it is sent to the IconMaster Control Panel. If this box is not checked, the switcher will be configured for Channel control only.
To add devices for control, click Add to create a new entry in the MKE List table, and then complete the fields in that row, as described in
Table 10-14 MKE List Table
Item
ID
MName
Description
An unique identifier for the device
A descriptive identifier for the device
192
Chapter 10
Configuring IconMaster
Table 10-14 MKE List Table (Continued)
Item
Multi Profile 1
Multi Profile 2
Multi Profile 3
Description
The first Multiviewer profile associated with the device
The second Multiviewer profile associated with the device
The third Multiviewer profile associated with the device
To remove a device from the list, select the row and then click Delete.
Each device in the MKE List appears in the MKE in Group table. To switch between controlled devices, MKEs are divided into groups.
To add devices to a group, follow theses steps.
1
In the Group List table, enter a descriptive name for the group in the Name field, and then check Enabled.
2
In the MKEs in Group list, place a check in the Enabled column for each device you want in that group.
3
Place a check in the Primary MKE beside the device you want to use as the master device in that group.
Only one device can be the primary device. To assign a different device as the primary device, remove the check beside the device that is already selected before selecting another device.
Note: If you are configuring an ISCP, the rest of the configuration for IconMaster group control is done within the IconMaster Software Control Panel wizard in CCS Navigator.
4
If you are configuring a hardware control panel, click Panel Configuration.
Figure 10-46 Panel Network Configuration in Group Mode
IconMaster
Installation and Configuration Manual
193
5
In the Master Assignment section of the dialog box, under Host Name, choose a group or channel as created on the MKE Group screen from the drop-down menu.
If the item selected is a channel, the IP Address and Multiviewers fields update to display information associated with the selected channel or group.
If the item selected is a group, the IP Address is 255.255.255.255.
(For other settings on this screen, see
Panel Network Configuration Settings
6
On the Button Configuration screen, assign buttons on Configurable Clusters 1 and 2 to the different groups as required (see
Quick Configuration Quick Reference Chart
This section provides a quick reference chart for the main control panel functions. It shows the control panel clusters (as illustrated in
on page 193), the functions that
fall within each cluster, and the ICU dialog box that allows you to configure that particular function.
ICONM-HCP Control Panel and ISCP
Configurable cluster 1
Parameter adjustment control cluster
Configurable cluster 2
AUX (Auxiliary) bus
PGM (Program) bus
LCD character input source display
PST (Preset) bus
Configurable Transition functions
Figure 10-47 Primary Busses on the Main Control Panel
Transition controls
194
Chapter 10
Configuring IconMaster
Table 10-15 Busses, Functions, and Configuration Utilities Relationships
Control Panel Item
Configurable cluster 1 and 2
Configurable cluster 2
Parameter adjustment control cluster
Aux bus
Program bus)
Functions
Fade to Black (FTB)
Fade to Silence (SIL)
CLOCK, TIMER
Quick Select (QS1•••QS8)
GPO output control
(GPO1•••GPO13)
Frame select (CH1•••CH8)
Fast Reset
Source Select (SRCSEL)
Keyer control (KEYER)
Transition control (TRANS)
Audio control (AUDIO)
Effects control (FX)
Quick Selects (Q-SEL)
Preconfigured auxiliary bus preview
(AUX)
PGM
PST (Preset) bus PST
Setup Information
Button Configuration (page 186)
System Configuration (page 173)
Audio Configuration (page 141)
System Configuration (page 172)
System Configuration (page 172)
IconMaster
Installation and Configuration Manual
195
Table 10-15 Busses, Functions, and Configuration Utilities Relationships (Continued)
Control Panel Item
Configurable transition functions
Transition control cluster
Functions
Hold
Transition Rate
Slow
Medium
Fast
Cut
Breakaway
Audio
Video
Transition Effects
FX
Transition Type
Take-fade
Fade-take
Fade-fade
Cross-fade
Machine Control Type
Cue
FF
Mark
Play
Rewind
Stop
External keys
Key 1•••Key 2
Internal keys
Key 3•••Key 6
Audio Over
Audio-over 1•••Audio-over 2
Background (BKGD)
Transition “hot” button
Preroll
Take
Fader bar
Setup Information
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
Audio Configuration (page 141)
—
System Configuration (page 172)
—
—
196
Chapter 10
Configuring IconMaster
ICONM-HCP-16 Control Panel
Configurable cluster 1 Parameter adjustment control cluster Configurable cluster 2
Optional audio control panel
AUX (Auxiliary) bus
PGM (Program) bus
LCD character input source display
PST (Preset) bus
Configurable
Transition functions
Transition “hot” button Transition controls
Figure 10-48 Primary Busses on the ICONM-HCP-16 Control Panel
Table 10-16 Busses, Functions, and Configuration Utilities Relationships
Control Panel Item
Configurable cluster 1 and 2
Configurable cluster 2
Parameter adjustment control cluster
Functions
Fade to Black (FTB)
Fade to Silence (SIL)
CLOCK, TIMER
Quick Select (QS1•••QS8)
GPO output control
(GPO1•••GPO13)
Frame select (CH1•••CH8)
Internal keys
Key 3•••Key 6
Source Select (SRCSEL)
Keyer control (KEYER)
Transition control (TRANS)
Setup Information
Button Configuration (page 186)
IconMaster
Installation and Configuration Manual
197
Table 10-16 Busses, Functions, and Configuration Utilities Relationships (Continued)
Control Panel Item
Aux bus
Program bus)
Functions
Audio control (AUDIO)
Effects control (FX)
Quick Selects (Q-SEL)
External keys
Key 1•••Key 2
Audio Over
Audio-over 1•••Audio-over 2
Preconfigured auxiliary bus preview
(AUX)
PGM
Setup Information
Audio Configuration (page 141)
Audio Configuration (page 141)
PST (Preset) bus
Configurable transition functions
PST
System Configuration (page 172)
System Configuration (page 172)
Button Configuration (page 186)
Button Configuration (page 186)
Transition control cluster
Hold
Transition Rate
Slow
Medium
Fast
Cut
Breakaway
Audio
Video
Transition Effects
FX
Transition Type
Take-fade
Fade-take
Fade-fade
Cross-fade
Machine Control Type
Cue
FF
Mark
Play
Rewind
Stop
Background (BKGD)
PANEL-LOCK
Transition “hot” button
Preroll
Take
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
Button Configuration (page 186)
—
System Configuration (page 172)
—
198
Chapter 10
Configuring IconMaster
11
Enabling a Router Database for
Use with an IconMaster System
199
Overview
The IconMaster makes use of the Imagine Communications router configuration tools to create a router database for use in the IconMaster’s setup and for select operations.
If you are connecting the IconMaster to a Imagine Communications router for which you already have a Router database, you can use this database as a starting point.
Otherwise, use CCS Navigator to create a router database consisting of all sources and destinations which will be used with your IconMaster system.
Once a router database has been created, you will use the Imagine Communications
Navigator software to send this database to the IconMaster. You can also edit the database at any time from within Navigator, and update the IconMaster with a simple button press.
To configure the IconMaster’s source inputs from the router, you will use the IconMaster
Configuration Utility (ICU) to assign router sources as IconMaster inputs.
Finally, if you have configured IconMaster inputs as Dynamic, you will use this database to assign new router sources to the IconMaster inputs.
This chapter provides you with the information you need to perform these procedures.
The discussion that follows is based on the assumption that you have a working knowledge of Routers and the Navigator software application, and have used their other capabilities. If not, please refer to the appropriate manuals to familiarize yourself with their functions.
Setting Up a Router Database
Note: Databases for several popular Imagine Communications router configurations have
been provided with your IconMaster system. These can be found in the IconTools software directory (typically C:\Program Files
Harris IconTools). You can use these databases,
or create your own. See page 132 for a list of these “getting started” database files.
The steps described below direct you through the process to use for adding a router to a router database. For illustration purposes, the discussion will focus on adding a Panacea
16×4 routing switcher via Polling. For specific information on adding or editing other
Imagine Communications routers, please see your CCS Navigator documentation.
200
Chapter 11
Enabling a Router Database for Use with an IconMaster System
If you have set up a router database for your IconMaster primary router already, you do not need to set it up again. Go directly to the section titled
1
Launch the Navigator application (Start
Programs Navigator).
2
In Build mode, select Router
Create Routing System from the Navigation pane.
Figure 11-1 Create Routing System Sequence of Steps
A dialog box opens.
Figure 11-2 Create Routing System Dialog Box
IconMaster
Installation and Configuration Manual
201
3
Enter a name for the router system, and then check Start from a blank configuration.
4
Click on Perform System Poll and enter the communication protocol and IP address for the Panacea router, and then click OK.
5
In Navigator’s Navigation pane, browse to Routers > <name> > Routers and double-click on the Panacea 0 item.
6
Select the Router Frame tab. Panacea module information such as matrix size, type, and module options will be displayed (see
Figure 11-3
). These will vary, depending on your
Panacea’s matrix type.
Figure 11-3 Router Frame Tab
7
Select the Detected Cards tab.
Panacea module information such as card type, back panel type, and firmware version will be displayed.
Figure 11-4 Detected Cards Tab
202
Chapter 11
Enabling a Router Database for Use with an IconMaster System
8
Select the Detected Matrices tab.
Matrix information should resemble the information shown in
Figure 11-5
.
Figure 11-5 Detected Matrices Tab
9
Click OK to close the dialog box.
When the database is first created, each logical source will be assigned a generic name such as “Input 1,” “Input 2,” etc. Each logical source can be renamed to uniquely identify the source. A source name can contain any 8 characters. To rename a source:
a
In the Navigation pane, select Routers > <name> > Control Views and double-click on the <Name> item.
The Edit Logical Database window will appear.
b
Select the Sources tab.
c
Highlight the text in the Name box.
Figure 11-6 Edit Logical Database
d
Over-type it with the new name.
IconMaster
Installation and Configuration Manual
203
e
Make sure that you follow the category/indexing format as described below.
When a source name is entered in the database, the name automatically creates a category. All characters to the left of last space in the source name become the category (the space will be included in the category name). All characters to the right of the space will become the index. If the source name does NOT include a space, the entire name will be used to create the category name. This may limit the number of sources that can be accessed from the panel. Use spaces appropriately when naming sources. If any character after the space is not a valid index character (valid characters are any combination of numbers, 0-9), the entire name will be used to create the category name.
If a logical source is named “VTR 1,” the category is named “VTR.”
If “VTR1” is typed without a space, the category “VTR1” will be created.
If “VTR 10Z” is typed, a category named “VTR 10Z” will be created (not a category
“VTR” and an index “10Z”).
10
If you made changes on any of the router tabs, the message “Needs Download” will appear next to the router name listed on the Navigation pane. Highlight the router and click
Download to download the revised settings to the router.
Defining the IconMaster Configuration
1
At the View for Administrators list, locate the Catalog selection. If necessary, expand the selection to view the sub-entries.
2
Under the IconMaster sub-entry, locate the IconMaster (MKE) entry. Drag the entry up to the Configuration selection, and then drop it into the Configuration selection.
3
Click Yes to confirm the operation.
204
Chapter 11
Enabling a Router Database for Use with an IconMaster System
Drag this item to the
Configuration Router view folder.
Drop item from Catalog folder here.
Drop item from Router folder here.
Drag this item to the
Configuration folder.
Figure 11-7 Drag-and-Drop IconMaster (MKE) Entry
The following dialog box appears:
Figure 11-8 IconMaster (MKE) IP Dialog Box
4
Enter the IP address of the MKE-3901 module, and then click OK.
5
If necessary, expand the Configuration selection to view the sub-entries. You will now see an entry for IconMaster (MKE), with a Router View sub-entry below it.
6
Drag the database entry under the Control View you created in step 6 on page 201 down
to the Configuration selection, and then drop it into the IconMaster’s Router View sub-entry.
7
Click Yes to confirm the operation.
The MKE Configuration dialog box appears.
IconMaster
Installation and Configuration Manual
205
Figure 11-9 MKE Configuration Wizard Screen 1 of 3
8
On the first screen of the configuration wizard, enter a name for the configuration, and then click Next.
You cannot make any other changes on this screen.
9
On the second screen of the configuration wizard, you can select the sources that you want to control. All of the sources that are established by the Router System Control View are listed under Available sources. From this list, select the sources you want to add, and then click the > button (or, if you want to add all of the sources listed, click the >> button).
If you want to remove a source, select the one you want to remove, and then click the < button, or click the << button to remove all sources.
You can filter the Available sources list by entering a keyword in the Filter box.
206
Chapter 11
Enabling a Router Database for Use with an IconMaster System
Figure 11-10 MKE Configuration Wizard Screen 2 of 3
Selected sources now lists the sources that you can control.
To determine the order in which the sources appear, use the following buttons:
Up—Moves the selected items up one position in the list
Down—Moves the selected items down one position in the list
Top—Moves the selected items to the top of the list
Bottom—Moves the selected items to the bottom of the list
A–Z—Organizes all items in the list by alphanumeric order
Z–A—Organizes all items in the list by reverse alphanumeric order
When you have completed organizing your Selected sources list, click Next.
10
On the third screen of the configuration wizard, select the destinations that you want to control, using the same tools and methods you used to add and remove sources.
IconMaster
Installation and Configuration Manual
207
Figure 11-11 MKE Configuration Wizard Screen 3 of 3
11
Click Finish.
12
Back in the Navigation pane, click the IconMaster (MKE) device in the Configuration folder.
Click this device to transfer the configuration.
This is the configuration you just created.
Figure 11-12 Navigation Pane with IconMaster Configuration
208
Chapter 11
Enabling a Router Database for Use with an IconMaster System
The Configuration dialog box opens.
Figure 11-13 Transferring a Configuration to the MKE-3901 Module
13
Highlight the device configuration you want to transfer, and do either of the following:
Click Perform Transfer to send the router database to the IconMaster. See
Performing a Database Transfer
This option is suitable for smaller router databases.
Click Export Configuration to save the router database locally before exporting the database to ICU for transfer. See
Exporting a Configuration and Importing in
This option is recommended for very large router databases.
Performing a Database Transfer
After completing the steps in
Defining the IconMaster Configuration
you have a smaller router database, you can transfer the router database directly to the
IconMaster.
1
On the Configuration dialog box within Navigator, click Perform Transfer.
2
Click Yes to confirm the transfer.
3
After the transfer is complete, click Refresh Device, and then click List Configuration.
The XML files will be listed on the right side under List of All Configurations on the
Device. Confirm that the config.xml and routerdb.xml files are listed.
4
Click IconMaster Configuration Utility.
ICU starts and loads the frame configuration for the selected device.
5
In ICU, click Router Configuration.
6
Choose either Serial port or Ethernet depending on your routing system, and enter the IP address if required.
IconMaster
Installation and Configuration Manual
209
(For Platinum routers only) Under External Router, select Ethernet, and then enter the IP address for the PT-RES module. The Acquire Router Database dialog box should open, with Download Database from IconMaster selected. (If this dialog box does not appear, check Using Routing Database.)
7
Click OK.
The routing database is now fully transferred to the IconMaster hardware. To confirm that it is mapped correctly, check that the router levels match the database configurations on the
Primary Inputs dialog box in ICU.
Exporting a Configuration and Importing in ICU
After completing the steps in
Defining the IconMaster Configuration
you have a very large router database, you should export the database to ICU. Follow these steps:
1
On the Configuration dialog box within Navigator, click Export Configuration.
2
Click Yes to confirm the transfer.
3
Click IconMaster Configuration Utility.
ICU starts and loads the frame configuration for the selected device.
4
Do either of the following:
If the ICU configuration is already set to use a router database (see
on page 217), then in ICU go to
File > Import Router
Database, and select the file that was exported from Navigator in Steps 1 and 2 above.
If the ICU configuration is not already set up to use a routing database:
i.
Click Router Configuration, and then choose either Serial port or Ethernet depending on your routing system.
ii.
Enter the IP address if required.
Panacea routers normally use serial port. For Platinum or IP3 routers under
External Router, select Ethernet, and then enter the IP address for the PT-RES or
PX-RES module.
iii. Select Using Routing Database and Sorted.
The Acquire Router Database dialog box should open, with Download
Database from IconMaster selected.
iv. Change this to Import a Database and then click OK.
Figure 11-14 Acquire Router Database Dialog Box
210
Chapter 11
Enabling a Router Database for Use with an IconMaster System v.
Select the file that was exported from Navigator in steps 1 and 2 above.
The routing database is now transferred to ICU.
5
Check Primary Inputs and Aux Inputs to ensure that sources and destinations are mapped correctly and then transfer the configuration to the IconMaster.The routing database is now fully transferred to the IconMaster hardware.
Preparing the IconMaster Configuration
1
Launch the IconMaster Configuration Utility (ICU) by selecting the button labeled Launch
IconMaster Config Utility or from the Start menu (Start
Programs Harris
IconTools
IconMaster IconMaster Configuration Utility).
2
If you have already created an IconMaster configuration, select File
Open, and then select your configuration file. Otherwise, select File
New, and then select the type of configuration to create (in this case, select IconMaster Frame (Channel) Configuration.)
Figure 11-15 New Configuration Window
3
Click OK.
The main ICU window appears.
4
Under the System Config category on the left side of the ICU window, select Genlock
and Standard.
From the Operation Standard drop-down list box select the operating standard you want to use.
IconMaster
Installation and Configuration Manual
211
Figure 11-16 Selecting Operation Standard
5
Under the System Config category on the left side of the ICU window, select Network.
Here you will identify the IconMaster’s MKE-3901 module’s Ethernet settings.
Enter a new name into the IconMaster Channel Name text box.
Enter the IP address, subnet mask, and (optionally) the network gateway settings for the IconMaster’s MKE-3901 module. When all entries are complete, close the Network window.
Figure 11-17 IconMaster MKE-3901 Network Settings
A few moments after entering the IconMaster IP address on the network page, the flashing
OFFLINE will change to ONLINE, to indicate that the IconMaster Configuration Utility has successfully detected and connected with the IconMaster MKE-3901 module.
212
Chapter 11
Enabling a Router Database for Use with an IconMaster System
6
Under the System Config category on the left side of the ICU window, select Router
Configuration. The Router Configuration window appears. Make the following selections:
Figure 11-18 Selecting Router Mode and Router Database Characteristics
a
Under Router Mode, click the External Router radio button.
b
Under Router Database, click the Using Router Database and Sorted check boxes.
The Acquire Router Database window appears.
Figure 11-19 Acquire Router Database Window
c
Select the database source, and then click OK.
Use Download Database from IconMaster if you want to use the database that is currently active on the IconMaster.
If you choose this option, click Yes to confirm that you want to download the XML file.
IconMaster
Installation and Configuration Manual
213
Figure 11-20 Download Confirmation Window
Use Import a Database to import the router database from Navigator if your router database is very large.
If you choose this option, after clicking OK, navigate to the location where the
Navigator routing database was saved and select Open (see
Configuration and Importing in ICU
Select Use Last Database from IconMaster if you want to use the database you used before.
The download starts.
d
Once the download is completed, click OK to close the Routing Database
Successfully Downloaded message.
e
Click OK in the You must save your configuration file before proceeding window to save the database.
Enter a location and file name for your configuration file in the Save As window.
If you are using a Platinum router, select “5” from the Router Transition Delay box for a 5-frame router transition delay. If not, use the default setting of “1”.
At the bottom left of the ICU window, you will see displayed the frame name, the operating standard, and the IP address you just entered. You will also see the word Connecting.
Assigning Router Inputs
1
Under the Input/Output category on the left side of the ICU window, click Primary Input.
The Primary Input window will appear.
214
Chapter 11
Enabling a Router Database for Use with an IconMaster System
Figure 11-21 Primary Input Window
Under Router Source Number, the level numbers displayed should match the levels set in your database. In the unlikely event that they do not, you can change the level number in the drop-down list boxes to match the levels set for your router. Set any unused level to
Unused. Note that the Video column must have a router level assigned.
Figure 11-22 Changing Router Levels
2
For sources that will be dynamic, click the check box (es) next to the appropriate source(s).
3
Select the desired router source(s), and then select name of the router source from the
Name drop-down list box.
IconMaster
Installation and Configuration Manual
215
Figure 11-23 Changing Router Source Names
4
For the Input Buses: Bus A and B, select the Name from the drop-down list box of the router destinations which are connected to the IconMaster’s A and B inputs.
Figure 11-24 Selecting Bus A and Bus B Inputs
5
Under the Input/Output category on the left side of the ICU window, click Aux Bus. The
Aux Bus window will appear.
216
Chapter 11
Enabling a Router Database for Use with an IconMaster System
Figure 11-25 Setting up Router Database Aux Operations
Note: When ICU is configured for Router Database mode, the Aux bus presentation changes to allow selections from the router database for configuration of database sources.
If a database source is missing for a particular level/crosspoint, click on the desired cell within the Aux bus page, and then click Manual. You can then override or assign a desired crosspoint data value.
6
From the Aux Bus menu in the top left of the dialog box, choose each bus, and then check or uncheck Enable.
Disabled Aux buses will not appear in the RCP, and will appear grayed out on the ISCP.
7
For enabled buses, type router sources, where they differ from those displayed on the screen.
8
Select File
Save As, and then enter a name for the configuration.
9
To send the configuration to the IconMaster, click the Send CFG to Frame button.
Figure 11-26 Sending Configurations to a Frame
At this point, you should have an operational IconMaster, which has inputs assigned from the router.
IconMaster
Installation and Configuration Manual
217
Changing or Editing the Router Database
If you need to add, delete or change an entry for the IconMaster’s router, you will want to update the router database. This procedure describes the workflow to perform this change and update.
1
From within the Navigator application, select the IconMaster router database entry under the Routers
Control Views tree.
Figure 11-27 Router Database Entry Location
2
Double-click the IconMaster’s router database entry to open the database editor.
You can edit, add, delete, or change entries as needed. If you adjust the logical system size of your router configuration to be specific to IconMaster, all source names, destination names, and router sources will have to be re-entered into the new database.
3
To update the database on your IconMaster, double-click the IconMaster (MKE) sub-entry under the Configuration selection.
The Configuration for IconMaster (MKE) window appears.
218
Chapter 11
Enabling a Router Database for Use with an IconMaster System
Figure 11-28 Configuration for IconMaster (MKE) Window
4
Highlight the device configuration you want to transfer, and then click Perform Transfer to send the router database to the IconMaster.
5
Click Yes to confirm the transfer.
6
After the transfer is complete, click Refresh Device.
Any router database changes you made will become active on the IconMaster within a few seconds. If you wish to change the assignment of router sources to IconMaster inputs, use the IconMaster Configuration Utility to make these changes.
12
Troubleshooting
IconMaster Troubleshooting Checklist
This checklist should be used to ensure that the basic system is configured and wired properly. It is important to follow though these in order; the logic here is important to diagnose configuration issues.
Breakout
Module
Ensure the correct cable(s) are used for connecting to the IconMaster. The audio cables and the video cable look very similar. If the wrong cable is used, the MKE-3901 module may not even power up properly. MKE breakout cable is part # 165-000242-00 the MKA breakout is part # 165-000242-00.
Communication
1
Verify correct IP addressing on MKE-3901, MGI-3903, RCP, and PC.
2
Verify all components connected to a 10/100baseT switch.
3
Check that the control panel has been configured to control the MKE-3901 IP address.
4
Ethernet port 1 on the control panel is not used. Port 2 must be connected.
Video Signals
1
Verify correct firmware version is loaded into both the MKE-3901 and MGI-3903 modules.
The version can be viewed from the card edge controls of each module. The letters SD or
HD will be at the end of the version tag. Both versions of firmware are available from our
Web site.
2
Verify the correct genlock type and operating standard is selected in the Genlock configuration of the IconMaster Configuration Utility (ICU). Once set, the file must be saved and uploaded to the frame. If the operating standard does not match with the firmware version in the module you will receive an error. Starting with v1.2 the software prompts you to load the firmware.
3
Verify genlock is present at the MKE-3901 module. There is a lock LED on the far left of the board that indicates valid signal presence.
4
Connect two video sources to the bus A and bus B inputs of the MKE-3901. By selecting different sources on the program bus you should see the program output toggle between the two sources.
219
220
Chapter 12
Troubleshooting
Video Output is not Valid
Bypass the IconMaster and ensure the input source feeding the BusA and BusB signals appear on your downstream monitor by connecting a BNC "barrel" of the cable feeding IconMaster BusA/B input and the PST or PGM output monitor.
Verify the signals feeding into IconMaster are of the correct video standard, as set up in the ICU configuration.
Internal Router Control (NEO NSM)
1
Verify correct settings on the NSM modules.
The “first” NSM, which is used for inputs 1-5, should be set to Level 0, SrcOffset 1,
DestOffset 0.
The “second” NSM, which is used for inputs 6-12, should be set to XY Level 1,
SrcOffset 1, DestOffset 0.
2
Verify that external router control is not selected in the System Config section of the ICU.
Some versions may have a check box to select internal routing, otherwise deselect external.
Any changes need to be uploaded to the frame.
3
Verify that LockStat 1 and LockStat 2 parameters on the NSM module are set to Free.
External Router Control (Panacea, Platinum, EDGE)
1
Verify jumpers on MKE-3901 module are set for RS-232 or RS-422 control.
2
Verify jumper pack on breakout module is set for RS-232 or RS-422.
3
Verify cable pinout is correct for RS-232 or RS-422 connection to the router.
4
Verify the router serial port is correctly set for RS-232 or RS-422.
5
Verify that the router serial port is set to 38400 baud.
6
Verify that the serial cable to the router is connected to port E on the breakout module.
7
Verify that the level, source, and destination setup in the System Config/External Router
Configuration of the ICU and wiring match.
Audio Overs
When using the breakout module the audio over jumpers on the MKE-3901 module must be set to balanced, even if unbalanced AES inputs are used.
Software/
Firmware
Verify the firmware versions of all IconMaster components: MKE-3901, MGI-390x, RCP,
ICU. All software and firmware components must be from the same release. If one component is upgraded, the entire system must be upgraded.
Cannot PING the IconMaster Components From a Computer
Check IP addresses of IconMaster component and that computer
Check network mask settings
Check computer for firewalls or blocked ports
Ensure you can PING any other network devices from that computer
Check the lights on the Ethernet router(s) to ensure all devices are connected and operational
IconMaster
Installation and Configuration Manual
221
RCP Cannot Connect To An IconMaster Channel (MKE)
If the RCP's channel button is RED, then the RCP has a valid Ethernet connection to the
MKE channel, and is receiving regular heartbeat (keepalive) messages.
If you press a GREEN channel button, and it does not turn (and remain) RED, there are network connectivity problems preventing the RCP and the MKE to connect. Check IP addresses, router connections, and equipment configuration settings.
Cannot Communicate to the Primary Router
If IconMaster cannot communicate to the primary router, the primary source buttons will
FLASH, indicating a router communications error.
Note: Some systems may indicate a router communications error (by flashing) only at powerup. Pressing any PST source button will clear this indication. This is normal, and does not indicate an error.
Ensure the BKGD button on the RCP panel is selected and illuminated. If not selected,
IconMaster will not change the background source on the PST bus. THIS IS THE MOST
COMMON MISUNDERSTANDING.
If set up for serial router communications:
Verify the correct serial port is set up (ICU, System Config > Router Configuration)
Verify RS232 -vs- RS422 settings (jumper on MKE -3901 (see
on page 20) and jumper pack on breakout module
(see
Verify correct serial port wiring is used (see
If using an SPT to connect to the router, verify the DIP switch settings on the SPT for baud rate, protocol select, and XY terminations. An internal jumper pack must also be set correctly for either RS-232 or RS-422.
If set up for Ethernet connection, verify the correct router IP address information (ICU,
System Config ' Router Configuration)
Using ICU, verify the router setup on the System Config > Router Configuration and the
Input/Output > Primary Input screen.
Verify the correct router level and destinations are set up (ICU, Input/Output ' Primary
Input).
Monitor the router BusA and BusB destinations using a router control panel. Try selecting different sources to these router outputs: do these changes propogate through to the
IconMaster outputs?
Cannot Control the Internal (Logo) Keyers
Internal logo keyers are only available for IconMaster systems with MGI-390x modules.
IconMaster LITE systems do not include this module, and will not support internal logo keyer operations.
222
Chapter 12
Troubleshooting
If the Internal Keyer buttons are dark and do not display any text, the IconMaster is configured as a LITE system and is not authorized to support internal logo generators/ keyers. If this is in error, contact Imagine Communications Customer Support to review the IconMaster LITE license and to verify your MGI-390x module is included.
IconMaster licenses are applied through the ICU's License Management menu:
Figure 12-1 Adding a License
Select Get License to retrieve and display the IconMaster's MKE-3901 module serial number, and provide this information to the Imagine Communications Customer
Support team.
If the Internal Keyer buttons display the message "NO MGI CARD FOUND", the MKE module has not detected the MGI module. Remove the IconMaster card set from the NEO frame, and check the module-to-module connections. Ensure the board-to-board screws are securely fastened.
If the Internal Keyer buttons display the message "PLEASE WAIT LOADING LOGOS", the
MGI module is still in the process of loading logos from its offline (Compact Flash) storage, to online DDR memory. This process may take some time, depending upon the number of logos, logo size and duration, etc.
The color of the Internal Keyer's tally LCD is also helpful in troubleshooting:
OFF = No MGI card discovered, or IconMaster LITE
GREEN = Logo keyer is available, and not on-air
RED = Logo keyer is on-air
Internal Key Appears Corrupted
Keys can appear corrupted if the HD video standard is changed while an internal key is on air.
When changing between HD operating standards (for example, from 1080I to 720P), you must repower the IconMaster.
IconMaster
Installation and Configuration Manual
223
Cannot Control the External Keyers
The color of the External Keyer's tally LCD is also helpful in troubleshooting, and indicates whether an external fill/key signal is present to the IconMaster, and if the signal is timed or non-sync with the PGM signal.
OFF = External fill/key signal is not present.
IF the keyer is configured for self-key, only the FILL signal is checked.
IF the keyer is configured for any other type of key, both the FILL and KEY signals must be present.
GREEN = Keyer has a valid signal, and is not on-air.
RED = Keyer is on-air
ORANGE = Keyer has a signal, but the signal is either invalid, or not properly timed with the PGM signal and is considered non-sync. It will key into the program video, but may be vertically offset from the intended on-screen location.
Navigating the Service Menu
You can access the Service menu through the Parameter Adjustment Control cluster. Via the
Service Menu, you can see the IconMaster software version in use, view or change the control panel IP address, or view the numeric value of a fader bar position.
To access the service menu:
On an ICONM-RCP, simultaneously press all four LCD buttons in the center Parameter
Control Cluster
On an ICONM-RCP16 panel, press the right control knob
Figure 12-2 Service Menu
To exit the service menu:
1
Turn the left scroll knob until the left LCD button displays EXIT.
2
Press the left LCD button.
Verifying the IconMaster Software Version
1
Access the Service Menu.
2
Turn the left scroll knob until the PNL S/W parameter appears. Reading from left to right, you will see a display of the current version of the control panel software. You cannot change this parameter.
3
Turn the left scroll knob until the PUSH EXIT parameter appears.
4
When finished, turn the PUSH EXIT display button to return to the main Parameter
Adjustment Control cluster menu.
224
Chapter 12
Troubleshooting
Changing IP Address for the Control Panel
1
Access the Service Menu.
2
Turn the left scroll knob until the PNL IP ADDR parameter appears. Reading from left to right, you will see a display of the control panel’s current IP address.
3
Select the button that contains the IP address component that you want to change, and then turn the right scroll knob to change the number on that button.
4
After you enter the last digit of the IP Address, press the right knob to save the new IP
Address.
5
When finished, turn the left scroll knob until the PUSH EXIT parameter appears.
6
Press the PUSH EXIT display button to return to the main Parameter Adjustment Control cluster menu.
Identifying Fader Bar Relative Positions
1
Access the Service Menu.
2
Turn the left scroll knob until the Fader Test parameter appears. The pushbutton on the extreme right will display a numeric value. This numeric value represents a straight linear value that denotes the relative position of the fader bar.
3
If necessary, move the fader bar up or down to the position you want. The numeric values in the right pushbutton will change to correspond with the fader bar’s relative position.
4
When finished, turn the left scroll knob until the PUSH EXIT parameter appears.
5
Press the PUSH EXIT display button to return to the main Parameter Adjustment Control cluster menu.
Getting Help from Customer Service
We are committed to providing round-the-clock, 24-hour service to our customers around the world. Contact our website or the Customer Service team
Table 12-1 Customer Service
Phone: 1-416-642-3611
Toll Free: 1-888-LEITCH6 (534-8246)
Fax: 1-416-445-9020
E-mail: [email protected]
13
Specifications
Overview
The following tables list specifications for the IconMaster system.
Specifications and designs are subject to change without notice.
Inputs
Serial Digital
Video
Table 13-1 Serial Digital Video Specifications
Item
Number of inputs
Standard
SDTV
HDTV
Equalization
Connector type
Return loss
Impedance
Specification
7; A, B, Fill1, Key1, Fill2, Key2, squeeze background
270 Mb/s per SMPTE 259M 525i/59.94, 625i/50
1.485 Gb/s serial per SMPTE 292M 1080i/50, 1080i/
59.94, 720p/50, 720p/59.94
Automatic up to 100m (328 ft.) of Belden 1694
BNC
>15 dB
75
225
226
Chapter 13
Specifications
Analog Video
Reference
Table 13-2 Analog Video Reference Input Specifications
Item
Connector type
Number of inputs
Return loss
Impedance
Reference type
Level
Connector type
Specification
BNC
1 Genlock
-40 dB to 6 MHz
75
NTSC/PAL, color black, or 525/625 comp sync or
Tri-Level per SMPTE 240M
29.97/30/60/25
200 mV to 2 V nominal
BNC
Outputs
Digital Video
Table 13-3 Digital Video Outputs Specifications
Item
Standard
SDTV
HDTV
Connector type
Number of outputs
Return loss
Impedance
Specification
270 Mb/s per SMPTE 259M 525i/59.94, 625i/50
1.485 Gb/s serial per SMPTE 292M 1080i/50, 1080i/
59.94, 720p/50, 720p/59.94
BNC
4; PGM (2), PST, CLEAN
>15 db
75
Keyers
Table 13-4 Keyer Output Specifications
Item
Number of keyers
Number of key processors
Key modes
Specification
6 (2 for IconMaster LITE)
2 external fill+key
4 internal (0 internal for IconMaster LITE)
Multiplicative; additive; self (Key 1, 2); matte (Key 1, 2)
IconMaster
Installation and Configuration Manual
227
System
Video Delay
Table 13-5 System Video Delay Specifications
Item
FX module installed
No FX module installed
SDTV
HDTV
Specification
+1 frame
3.7
1.5
s + (0 to 1) video line
s + (0 to 1) video line
Audio
Embedded
Table 13-6 Embedded Audio Specifications
Item
Standard
SDTV
HDTV
Specification
Per SMPTE 272M (embedded as 20-bit audio only)
Per SMPTE 299M (embedded as 24-bit audio)
48 KHz per AES3-1992
Channels
SD
HD
Mode
HANC
SDTV
HDTV
2 or 4 groups (4 or 8 AES pair, 8 Ch. Discrete)
4 groups (8 AES pair, 8 Ch. Discrete)
Delete existing and rewrite new audio groups
Non-audio data will be repacked and rewritten
Non-audio data will not be repacked and rewritten
Discrete Audio for Audio Over
Table 13-7 Discrete Audio for Audio Over Specifications
Item
Input/Output
Resolution
Specification
2 AES
24-bit operation (20 bit operation set at the output by configuration)
Sampling rate
Input
Sample rate converter
SRC disable
Connector
Format
48 KHz (33, 44.1KHz)
No
Multi-pin DB62
AES audio levels
228
Chapter 13
Specifications
Discrete AES Audio Bus A and B
Note: AES 3-1992 allows the LSB to be used for “Non-Program Audio.” If the LSBs are being used this way, the SRC must be turned off to allow for 20-bit operation. If the data is
20 bit, but the LSBs are all “0,” no action needs to be taken.
The following specifications apply when the optional MKA-3901 audio module is used in conjunction with the IconMaster.
Table 13-8 Discrete AES Audio Bus A and B Specifications
Item
Input
Output
Resolution
Input
Specification
4 AES in each for bus A and B
4 AES for PGM, PST, Clean
20- or 24-bit operation, set by data configuration bits
(with SRC off)
24-bit operation
Output
Sample rate converter
SRC disable
Sampling rate
Input
Output
Connector
Format
No
48 KHz (33, 44.1 KHz)
48 KHz
Multi-pin DB62
AES audio levels
Audio
Processor
Table 13-9 Audio Processor Specifications
Item Specification
Number of bus inputs 2 - A, B
Number of AES streams
4
Channel assignment Not restricted within A path or B path
Modifiers
Left or right invert
Left and right sum
Independent left and right level
Number of audio overs 2
Transitions
Dolby-E handling
Audio delay
Dissolve, cut, fade-fade, cut-fade, fade-cut
Restricting transition to “cut”
Other actions TBC
160
s without FX module installed
+1 frame with FX module installed
IconMaster
Installation and Configuration Manual
229
AES User and Configuration Bits
Table 13-10 AES User and Configuration Bits Specifications
Item
C bits input
C bits output
U bits input
U bits output
Specification
Read and analyzed for Format, word size only
Reinserted based on ICU settings
Selectable individually for each AES path
Implementation level is “standard”
Not read or used
Reset to 0
Common for all AES paths
Monitoring
Audio Level
Table 13-11 Monitoring Audio Level Specifications
Item Specification
Monitor gain control 0 to 100%
VANC Data
For 525 systems, line 21 may be selected to be part of active picture or blanking. Set this parameter using the IconMaster configuration utility software.
Table 13-12 VANC Data Specifications
Item
VANC data
Specification
Data will be allowed to “pass through” video processor
GPI Inputs and Outputs
It is assumed that these inputs/outputs are externally isolated. They are low voltage TTL style input/outputs.
Input
Table 13-13 GPI Input Specifications
Item
Quantity
Type
Polarity
Voltage range
Current load
Connector
Specification
18 (8 for IconMaster LITE)
Non isolated TTL
Software specified
-0.3 V to 5.3 V max
1 mA
Part of 62-pin “D”-type
230
Chapter 13
Specifications
Output
Table 13-14 GPI Output Specifications
Item
Quantity
Type
Polarity
Voltage range
Load
Connector
Specification
13 (7 for IconMaster LITE)
Open drain
Software specified
-0.3 V to 5.3 V max
40 mA max
Part of 62-pin “D”-type
Power Consumption
Table 13-15 Power Consumption
Item
Control panel
Frame
Power Consumption
250 W maximum; 150 W typical
NEO: <25 W
Panacea: 70 W (1RU) or 105 W (2RU)
MGI-3903
Table 13-16 Ethernet Port Specifications
Item
Standard
Connector
Specification
10/100Base-T IEEE 802.3u
8-pin RJ-45
Miscellaneous Items
Table 13-17 Miscellaneous Specifications
Item
Timecode IN
Specification
Per ANSI / SMPTE 12M, XML Female supporting unity speed, forward counting LTC
Timecode OUT Per ANSI / SMPTE 12M, XLR Male
IconMaster
Installation and Configuration Manual
231
Table 13-17 Miscellaneous Specifications
Ethernet
Temperature probe
10/100BaseT IEEE 802.3u Via RJ-45, 8-pin
12-36 VDC, 4-20 mA via 44-pin, HD-type female connector
Temperature
Performance
Operating
41° – 104°F (5° – 40°C)
32° – 122°F (0° – 50°C)
232
Chapter 13
Specifications
Index
A
Adaptor replacement information 79
–
AES input and output pinouts 29
AES user and configuration bits specifications 229
–
All, Operator, and Tree View parameters 54
Analog video reference specifications 226
Audio
audio configuration settings 141
audio over matrix settings 146
breakout module
,
–
–
Audio breakout module
–
Aux
bus configuration settings 147
B
Background
–
Buttons
button configuration settings 186
–
, ??–
Bypass relay control and jumper 33
C
Changing
channel positions 155 channel squeeze ratios 155
Communication protocols of IconLogo 103
Computer minimum requirements 7
Configuration, non-network 135
Configuring
Connectors
,
main control panel components 18
–
Control control panel
CPU BOOT. See DIP switch settings
Creating
Customizing control panel pushbuttons 47
D
Desk and tabletop mounting of control panels 14
Digital video specifications 226
Discrete
Display
233
234
Index
E
Effects changing
channel positions 155 channel squeeze ratios 155
editing names 153 enabling 153
resetting 154 selecting channels 154
Embedded audio specifications 227
Emergency Alert System (EAS)
Enable Silence While FTB option 150
Enabling
Ethernet
,
miscellaneous specifications 231
F
G
Genlock
GPI
GPO
H
I
IconMaster Configuration Utility
menu groups
–
, ??–
–
menus
–
ICONM-BO-V. See Video breakout
module
ICONM-BO-VAB. See Audio breakout
module, balanced
ICONM-BO-VAC. See Audio breakout
module, coaxial
–
Installation
–
IconMaster Configuration
–
J
–
IconMaster
Installation and Configuration Manual
235
K
Keyer
L
LEDs
M
Machine control
disabling settings 163 selecting automation types 163 selecting settings 163
–
Menu groups
–
,
??–
frame configuration
Minimum requirements of
Minimum system requirements 133
Miscellaneous specifications 230
pinouts
–
,
,
Modes of operation
Monitoring audio level
,
Multifunction I/O connector 27
N
–
O
Opening Existing ICU databases 138
Operator, Tree View, and All List
P
Panel network configuration
Parameter adjustment control cluster
parameter lists
Parameters
Pinouts
–
Power consumption
Power supply
Preroll
enabling status 164 setting duration 164
–
236
Index
Q
R
Rack mounting of control panel 15
–
Router configuration settings 170
Routers
RS-232 and RS-422 protocols 36
–
S
Selecting
Serial
digital video specifications 225
Set All Durations Equal to Current
Settings
147 auxiliary bus configuration 147
–
,
??–
panel network configuration 185
–
–
Setup
Software version, verifying 223
AES user and configuration
–
discrete audio 227 embedded audio 227
Standard, operating
System configurations
T
Table and desktop mounting of
–
Temperature specifications 231
Transition control cluster
Transitions
,
Tree View, Operator, and All List
U
–
V
Verifying software version 223
Vertical blanking interval. See Closed
captioning
Video
W
IconMaster
Installation and Configuration Manual
237
238
Index
Preuzimanje
Javni link je ažuriran
Javni link do vašeg ćaskanja je ažuriran. You may view and manage your chat links after registration here.
Javni link dokumenta
Reklama
