- Computers & electronics
- Telecom & navigation
- Two-way radios
- Motorola
- ASTRO APX 7000 Series
- User manual
advertisement
![Motorola ASTRO APX 7000 Series User manual | Manualzz Motorola ASTRO APX 7000 Series User manual | Manualzz](http://s3.manualzz.com/store/data/029642119_1-7f6a7634d1b925758563662b9dc58c97-360x466.png)
APX7000_DD_FrontCover.fm Page 1 Wednesday, May 7, 2014 1:38 PM
APX™ TWO-WAY RADIOS
APX 7000/APX 7000L
DUAL DISPLAY
USER GUIDE
APX_7000_Dual_Display.book Page 1 Thursday, June 19, 2014 10:38 PM m
ASTRO
®
APX™ 7000/APX 7000L
Series
Digital Portable Radios
Quick Reference Card
RF Energy Exposure and Product Safety
Guide for Portable Two-Way Radios
ATTENTION!
This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety
Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and
Regulations.
16-Position
Select Knob
__________
On/Off/Volume
Control Knob
Top Side (Select)
Button
__________
PTT Button
Antenna
Top
Display
Bluetooth
Pairing
Indicator
Main
Speaker
Receiving and Transmitting
1
Select zone/channel.
2
Listen for a transmission.
OR
Press and hold Volume Set button.
OR
Press Monitor button and listen for activity.
3
Adjust volume, if necessary.
4
Press the PTT button to transmit; release to receive.
Sending an Emergency Alarm
Radio Controls
Top (Orange)
Button
__________
3-Position A/B/C
Switch
__________
Side Button 1
__________
1
Press and hold the Emergency button*.
Microphone
2-Position
Concentric Switch
__________
Side Button 2
__________
Battery
2
The display shows Emergency and the current zone/channel. Radio sounds a short, medium-pitched tone, and the LED blinks red momentarily.
Accessory
Connector
Main Display
Home Button
Secondary Speaker
Menu Select
Buttons
Data Feature
Button
Radio On/Off
• On – On/Off/Volume knob clockwise.
• Off – On/Off/Volume knob counterclockwise.
Zones and Channels
• Zone – Zone switch to desired zone.
3
When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency.
* Default emergency button press timer is set
to 1 second. This timer is programmable, see page 68 in the user guide for details.
To exit emergency at any time, press and hold the Emergency button.
Keypad
4-Way Navigation
Button
• Channel – Channel switch to desired channel.
*68007024034*
68007024034-G
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners. © 2009–2014 by Motorola Solutions, Inc. All Rights Reserved. 05/14
1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A.
English
APX_7000_Dual_Display.book Page 2 Thursday, June 19, 2014 10:38 PM
Sending an Emergency Call
1
Press the Emergency button.
2
Press and hold the PTT button. Speak clearly into the microphone.
3
Release the PTT button to end call.
4
Press and hold Emergency button to exit emergency.
To exit emergency at any time, press and hold the Emergency button.
Sending a Silent Emergency Call
1
Press the Emergency button.
2
The display does not change; the LED does not light up, and there is no tone.
3
Silent emergency continues until you:
Press and hold the Emergency button to exit emergency state.
OR
Press and release the PTT button to exit the
Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode.
To exit emergency at any time, press and hold the Emergency button.
Display Status Icons
u t
Receiving a call or data.
Transmitting a call or data.
8 v
Blinks when the battery is low.
The more stripes, the stronger the signal strength for the current site
(trunking only).
O j
Direct radio to radio communication or connected through a repeater.
On = Direct
Off = Repeater
H
M
OR
.
i
This channel is being monitored.
L = Radio is set at Low power.
H = Radio is set at High power.
Scanning a scan list.
Blinking dot = Detects activity on the
Priority-One Channel during scan.
Steady dot = Detects activity on the
Priority-Two Channel during scan.
k
The vote scan feature is enabled.
Menu Navigation
< or > to Menu Entry.
{
,
|
, or
}
directly below Menu
Entry to select.
H to exit.
English
o b a m l
G n
On = Secure operation.
Off = Clear operation.
Blinking = Receiving an encrypted voice call.
On steady = View mode
Blinking = Program mode
On = AES Secure operation.
Off = Clear operation.
Blinking = Receiving an encrypted voice call.
On = feature enabled, and signal available.
Off = feature disabled.
Blinking = feature enabled, but signal unavailable.
On = User is currently associated with the radio.
Off = User is currently not associated with the radio.
Blinking = Device registration or user registration with the server failed due to an invalid username or pin.
Data activity is present.
Bluetooth is ready.
Bluetooth is connected to the device.
U or D to scroll through sub-list.
{
,
|
, or
}
directly below Menu
Entry to select.
Contents
Declaration of Conformity......................... 9
Important Safety Information........13
Software Version............................14
Notice to Users (FCC and Industry
Canada)....................................................14
Consignes de sécurité importantes.................................15
Version logicielle........................... 16
Avis aux utilisateurs (FCC et Industrie
Canada)....................................................16
Computer Software Copyrights....17
Documentation Copyrights...........18
Disclaimer.......................................19
Getting Started............................... 20
How to Use This Guide..................................20
Notations Used in This Manual......................20
Additional Performance Enhancement.......... 20
ASTRO 25 Enhanced Data.................20
Dynamic System Resilience (DSR).... 21
CrossTalk Prevention..........................21
Encrypted Integrated Data (EID).........21
SecureNet...........................................21
Conventional Talkgroup and Radio
Scan Enhancements......................21
What Your Dealer/System Administrator
Can Tell You.............................................22
Preparing Your Radio for Use.......23
Charging the Battery......................................23
Attaching the Battery..................................... 23
1
English
2
English
Attaching the Antenna................................... 24
Removing and Attaching the Accessory
Connector Cover...................................... 25
Using the Carry Holder.................................. 26
Turning On the Radio.................................... 28
Adjusting the Volume.....................................29
Identifying Radio Controls............ 30
Radio Parts and Controls...............................30
Programmable Features................................31
Assignable Radio Functions............... 32
Assignable Settings or Utility
Functions....................................... 35
Accessing the Preprogrammed Functions.....36
Menu Select Buttons...........................36
Home Button.......................................37
4-Way Navigation Button.................... 37
Data Feature Button............................37
Keypad...........................................................37
Mode..............................................38
Mode..............................................39
Mode..............................................40
Keypad Characters – Hexadecimal
Mode..............................................41
Push-To-Talk (PTT) Button............................42
Identifying Status Indicators.........43
Status Icons...................................................43
Text Messaging Service (TMS) Indicators.....48
TMS Status Icons................................48
TMS Menu Options............................. 50
Call Type Icons..............................................50
LED Indicator.................................................51
Intelligent Lighting Indicators......................... 52
Alert Tones.................................................... 53
Phone Call Displays and Alerts..................... 57
General Radio Operation...............59
Selecting a Zone............................................59
Selecting a Radio Channel............................ 60
Selecting a Channel via Channel Search
Button....................................................... 60
Mode Select Feature..................................... 61
Saving a Zone and a Channel to a
Softkey...........................................61
Saving a Zone and a Channel to a
Button............................................ 62
Receiving and Responding to a Radio Call... 62
Talkgroup Call................................63
Private Call (Trunking Only)...........63
Telephone Call (Trunking Only).....64
Making a Radio Call.......................................64
Making a Talkgroup Call..................... 65
Making a Private Call (Trunking
Only).............................................. 65
Making an Enhanced Private Call
(Trunking Only).............................. 66
Making a Telephone Call (Trunking
Only).............................................. 67
Switching Between Repeater or Direct
Operation Button...................................... 68
Monitor Feature............................................. 68
Monitoring a Channel..........................68
Monitoring Conventional Mode........... 69
Advanced Features........................70
Advanced Call Features................................ 70
Conventional Only)........................ 70
(Conventional Operation Only)...... 71
Sending a Status Call......................... 72
Only).............................................. 72
Dynamic Zone Programming (DZP)....74
Contacts.........................................................76
Making a Private Call from Contacts...77
Adding a New Contact Entry...............78
Deleting a Contact Entry.....................79
Adding a Contact to a Call List............79
Removing a Contact from a Call
List................................................. 80
Methods of Contact Editing in a
Call List.......................................... 80
Viewing Details of a Contact............... 82
Scan Lists...................................................... 82
Viewing a Scan List.............................82
Editing the Scan List........................... 82
Changing the Scan List Status............83
Viewing and Changing the Priority
Status.............................................84
Scan...............................................................84
Turning Scan On or Off.......................85
3
English
4
English
Making a Dynamic Priority Change
(Conventional Scan Only)..............85
Deleting a Nuisance Channel............. 85
Restoring a Nuisance Channel........... 86
Call Alert Paging............................................86
Receiving a Call Alert Page................ 86
Sending a Call Alert Page...................86
Emergency Operation....................................88
Sending an Emergency Alarm............ 89
(Trunking Only).............................. 89
Sending an Emergency Alarm with
Emergency Call............................. 90
Sending a Silent Emergency Alarm.... 91
Emergency.....................................91
Emergency Keep-Alive Feature.......... 91
Fireground (Conventional Only).....................92
Entering Fireground Zone Channel.....92
Responding to Evacuation Indicator... 93
Tactical Public Safety(TPS) (Conventional
Only)......................................................... 94
Using TPS Normal Transmission........94
Transmission................................. 94
Man Down......................................................95
Pre-Alert Timer....................................96
Post-Alert Timer.................................. 96
Feature is Triggered...................... 97
Triggering Emergency.........................97
Enhanced is Triggered...................97
Exiting Man Down Feature..................98
Re-Initiating Man Down.......................98
Testing the Man Down Feature...........98
Automatic Registration Service (ARS)...........99
Mode..............................................99
User Login Feature........................... 100
Text Messaging Service (TMS)................... 102
Accessing the Messaging Features.. 102
Text Message.............................. 103
Sending a Quick Text Message........ 104
Priority Status and Request Reply of a New Text Message............... 105
ASTRO 25 Advanced Messaging Solution..112
Advanced Messaging Solution.... 113
Two-Factor Authentication................ 113
Sending a Query...............................115
Receiving a Query............................ 117
Secure Operations.......................................117
Selecting Secure Transmissions.......118
Selecting Clear Transmissions......... 118
Managing Encryption........................ 118
Security........................................................123
Radio Lock........................................123
Radio Stun and Kill...................................... 126
Radio Stun........................................ 126
Radio Kill...........................................126
Global Positioning System (GPS)................127
GPS Operation..................................128
GPS Performance Enhancement......129
(Using GPS).................................129
Military Grid Reference System
(MGRS) Coordinates................... 130
Accessing the Outdoor Location
Feature........................................ 130
Saving a Waypoint............................131
Viewing a Saved Waypoint............... 132
Editing the Alias of a Waypoint......... 132
Waypoint......................................133
Deleting a Single Saved Waypoint....134
Deleting All Saved Waypoints...........135
Bearing from a Saved Waypoint.. 135
Mode............................................135
(ASTRO Conventional only)........ 136
Geofence (ASTRO 25 Trunking System).... 137
Entering the Geofence Area............. 137
Trunking System Controls........................... 138
Using the Failsoft System................. 138
Out-of-Range Radio..........................139
Site Trunking Feature....................... 139
Locking and Unlocking a Site............139
Site Display and Search Button........ 140
Mission Critical Wireless - Bluetooth
®
Turning the Bluetooth On..................141
Turning the Bluetooth Off..................142
Re-Pair Timer....................................142
Bluetooth Drop Timer........................143
Motorola Proximity Pairing (LF-
MPP) Feature.............................. 145
Radio Indications of Lost Bluetooth
Connection...................................146
Standard Pairing Feature..................146
PIN Authentication in Pairing............ 149
Turning On the Bluetooth Audio
Radio to the Headset)..................152
5
English
6
English
Turning Off the Bluetooth Audio
Headset to the Radio)..................153
Adjusting the Volume of the Radio from Bluetooth Audio Device....... 153
Viewing and Clearing the Bluetooth
Device Information.......................154
Clearing All Bluetooth Devices
Information...................................155
Editing the Bluetooth Friendly
Name........................................... 156
Pairing with LEX 700.........................156
Programming Over Project 25 (POP 25)
(ASTRO 25 and ASTRO Conventional). 157
Responding to the Notification of
Upgrade....................................... 157
Voice Announcement...................................158
Site Selectable Alerts (ASTRO 25)..............159
Sending SSA Notification to Single
Site...............................................159
Sending SSA Notification to Single
Site Via Manual Entry.................. 160
Sending SSA Notification to All
Sites.............................................161
Sending SSA Notification to All
Available Sites............................. 162
Stopping SSA Notification of a
Single Site....................................162
Stopping SSA Notification of a
Single Site Via Manual Entry....... 163
Stopping SSA Notification of All
Sites.............................................163
Stopping SSA Notification of All
Available Sites............................. 164
Long Term Evolution (LTE)..........................164
Data Profiles Available for LTE......... 166
Menu Screen............................... 166
Button.......................................... 167
Turning Off the LTE Connection....... 168
Information at the LTE Screen.......... 168
Scenario of Changing from LTEenabled Channel to LTEdisabled Channel......................... 169
Scenario of Changing from LTEenabled Channel to
Unprogrammed Channel............. 170
Scenario of Entering or Exiting
Out-of-Range Site........................170
Utilities......................................................... 170
Viewing Recent Calls........................170
Using the Flip Display....................... 171
Selecting a Basic Zone Bank............171
Selecting an Enhanced Zone Bank.. 171
Selecting the Power Level................ 172
Selecting a Radio Profile...................173
Enabling and Disabling the Radio
Alias............................................. 174
Selecting the Audio Speaker.............174
Controlling the Display Backlight...... 175
Locking and Unlocking the Keypad and Controls................................ 175
Turning the Controls and Keypad
Buttons Tones On or Off..............176
Turning Voice Mute On or Off........... 176
Using the Time-Out Timer.................176
Time and Date Setup........................177
Operation Features......................178
Using the PL Defeat Feature............ 179
Digital PTT ID Support...................... 179
Smart PTT Feature (Conventional
Only)............................................ 179
Transmit Inhibit................................. 180
IMPRES Battery Annunciator............181
General Radio Information................182
Helpful Tips.................................. 186
Radio Care...................................................186
Cleaning Your Radio.........................187
Proper Ways to Handle the Radio.... 187
Radio Service and Repair.................188
Battery Care.................................................188
Battery Charge Status.......................188
Battery Recycling and Disposal........ 190
Accessories..................................191
Maritime Radio Use in the VHF
Frequency Range..................... 192
Special Channel Assignments.....................192
Emergency Channel......................... 192
Non-Commercial Call Channel......... 192
Operating Frequency Requirements............192
Declaration of Compliance for the Use of
Distress and Safety Frequencies............195
Technical Parameters for Interfacing
External Data Sources............................195
7
English
8
English
Glossary........................................196
Limited Warranty..........................203
PRODUCTS........................................... 203
AND FOR HOW LONG:......................... 203
II. GENERAL PROVISIONS:....................... 204
III. STATE LAW RIGHTS:............................204
IV. HOW TO GET WARRANTY SERVICE:.204
V. WHAT THIS WARRANTY DOES NOT
COVER:..................................................205
PROVISIONS:........................................ 205
VII. GOVERNING LAW:...............................207
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Declaration of Conformity
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.
Phone Number: 1-800-927-2744
Hereby declares that the product:
Model Name: APX 7000/ APX 7000L conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
English
9
10
English
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Additional FCC Note to Users
The following FCC information applies to Bluetooth radio options.
Model Name: MNUK6000 & APX7000L
Description: APX7000/APX 7000L Bluetooth Option Board
FCC ID: AZ489FT6000 & AZ489FT7059
IC: 109U-89FT6000 & 109U-89FT7059
Conforms to the following regulations: FCC Part 15, Section 15.19, 15.21, and 15.105
Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the FCC, to operate this device and should not be made. See 47 CFR Part 15.21. Information to the user. The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Part. 15.19(3).
This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for equipment compliance should note that the limits specified in this part will not prevent harmful interference under all circumstances.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. See Part 15.105b These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
11
English
12
English
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Statements:
This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210. This product also complies with CAN ICES-3 (B) / NMB-3 (B).
Note: If the customers are purchasing the Bluetooth Option Board for the first time and their radios are FM approved, please send the radios back to the service center in order to keep the certification.
If customers have already purchased the radio with the Bluetooth Option Board as part of the tanapa and they need to replace (repair) the option board, they can send the radio to any Motorola FM audited.
Important Safety Information
RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios
ATTENTION!
This radio is restricted to Occupational use only.
Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way
Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations.
For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website:
http://www.motorolasolutions.com/APX
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry
Canada to operate with Motorola-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
English
13
Software Version
All the features described in the following sections are supported by the radio's software version R13.00.00 or later.
Accessing the Radio Information
on page 182 to determine your radio software version.
Check with your dealer or system administrator for more details of all the features supported.
Notice to Users (FCC and Industry Canada)
This device complies with Part 15 of the FCC rules and RSS 210 of the Industry Canada rules per the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
• Changes or modifications made to this device, not expressly approved by Motorola, could void the user's authority to operate this equipment.
14
English
Consignes de sécurité importantes
Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit
ATTENTION!
Cette radio ne doit être utilisée qu'à des fins
professionnelles. Avant d'utiliser la radio, lisez le guide Radios bidirectionnelles portatives : exposition aux radiofréquences et sécurité du produit, qui contient d'importantes instructions de fonctionnement pour une utilisation sécuritaire et des informations sur l'exposition aux fréquences radioélectriques, dans le but d’assurer votre conformité aux normes et règlements en vigueur.
Visitez le site Web suivant pour obtenir la liste des antennes, des batteries et des autres accessoires approuvés par Motorola :
http://www.motorolasolutions.com/APX
Selon la réglementation d'Industrie Canada, cet
émetteur radio ne peut être utilisé qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvés par Industrie Canada pour cet
émetteur. Afin de limiter les interférences radio pour les autres utilisateurs, le type et le gain de l'antenne doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) ne soit pas plus forte qu'il ne le faut pour établir la communication.
Cet émetteur radio a été approuvé par Industrie
Canada pour utilisation avec une antenne approuvée par Motorola offrant le gain maximal autorisé et l'impédance requise pour le type d'antenne indiqué. Il est strictement interdit d'utiliser avec cet appareil tout type d'antenne ne figurant pas dans cette liste et présentant un gain supérieur au maximum indiqué pour le type.
Français
(Canada)
15
Version logicielle
Toutes les fonctions décrites dans les sections suivantes sont prises en charge par la version
R13.00.00 ou les versions ultérieures du logiciel de la radio.
Pour obtenir davantage de renseignements à propos des fonctions prises en charge, adressez-vous à votre détaillant ou à votre administrateur de système.
16
Avis aux utilisateurs (FCC et Industrie
Canada)
Cet appareil est conforme à la Partie 15 des règlements de la FCC et RSS 210 du règlement d'Industrie Canada selon les conditions énumérées ci-dessous:
• Ce dispositif ne doit pas causer d'interférences nuisibles.
• Cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent perturber le fonctionnement.
• Les changements ou les modifications apportées
à ce dispositif, non expressément approuvées par
Français
(Canada)
Motorola, peuvent annuler le droit de l'utilisateur à utiliser cet équipement.
Computer Software Copyrights
The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program.
Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal nonexclusive license to use that arises by operation of law in the sale of a product.
English
17
Documentation Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of
Motorola.
18
English
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable.
However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others.
English
19
Getting Started
How to Use This Guide
This User Guide covers the basic operation of the
APX Portables.
However, your dealer or system administrator may have customized your radio for your specific needs.
Check with your dealer or system administrator for more information.
20
Notations Used in This Manual
Throughout the text in this publication, you will notice the use of Warning, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.
Warning: An operational procedure, practice, or condition and so on, which may result in injury or death if not carefully observed.
Caution: An operational procedure, practice, or condition and so on, which may result in damage to the equipment if not carefully observed.
Note: An operational procedure, practice, or condition and so on, which is essential to emphasize.
The following special notations identify certain items.
Example
Home button or
Phon
Description
Buttons and keys are shown in bold print or as an icon.
Menu entries are shown similar to the way they appear on the radio’s display.
This means “Press the right side of the 4-Way Navigation Button”.
Additional Performance Enhancement
The following performance enhancements are some of the latest creations designed to enhance the security, quality and efficiency of the radios.
ASTRO 25 Enhanced Data
ASTRO 25 Enhanced Data is optimized to handle different message sizes and variable update rates from different applications of the radio. Add Enhanced
Data to the Integrated Data system with a software
English
installation to improve data channel efficiency and enable denser network traffic.
Dynamic System Resilience (DSR)
DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV&D) or data centric are all supported by
DSR.
CrossTalk Prevention
This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the
Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk.
Encrypted Integrated Data (EID)
EID provides security encryption and authentication of IV&D data bearer service communication between the radio and the Customer Enterprise Network.
SecureNet
SecureNet allows user to perform secured communications on an Analog or Motorola Data
Communication (MDC) channel. The MDC Over-the-
Air Rekeying (OTAR) feature will allow users to perform OTAR activities on an MDC channel.
Conventional Talkgroup and Radio Scan
Enhancements
A few enhancements have been made to the
Conventional Talkgroup at the system. These enhancements improve the Scan feature operation significantly when multiple agencies are using a single conventional radio frequency channel. These enhancements allow users to use Selective Squelch to operate on only the subset of talkgroups that are relevant to the users rather than all talkgroups on the channel. These Scan improvements have been made to eliminate the audio holes that were present and to turn on the busy LED when activity is present on the channel. Mixed Vote Scan and Standard
Conventional Scan configurations are supported.
Priority Operation is also supported.
Up to 30 different talkgroups can be supported using conventional channels. A maximum of four talkgroups
21
English
can be supported when Vote Scan channels are being used.
Smart PTT is supported with this enhancement as
Smart PTT prevents users from transmitting while other users are on the channel.
Note: User Selectable Talkgroups are not compatible with this Conventional Talkgroup Enhancement.
What Your Dealer/System Administrator Can
Tell You
Check with your dealer or system administrator for the correct radio settings, if the radio is to be operated in extreme temperatures (less than -30 °C or more than +60 °C), to ensure proper top and front display operation.
You can consult your dealer or system administrator about the following:
• Is your radio programmed with any preset conventional channels?
• Which buttons have been programmed to access other features?
• What optional accessories may suit your needs?
22
English
Note: Specifications may vary for different radio models. Check with your dealer or system administrator for more information.
Preparing Your Radio for Use
This section provides simple instructions to prepare your radio for use.
Charging the Battery
Warning: To avoid a possible explosion:
• Do not replace the battery in any area labeled hazardous atmosphere.
• Do not discard batteries in a fire.
The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of
Motorola-authorized batteries and chargers available for use with your radio, see
191.
Note: When charging a battery attached to a radio, turn the radio off to ensure a full charge.
To charge the battery, place the battery (with or without the radio) in a Motorola-approved charger.
The LED on the charger indicates the charging progress; see the charger user guide.
Attaching the Battery
If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal.
Check with your dealer or system administrator for more information.
You can view the status of the IMPRES
™
battery if the radio is using an IMPRES battery. See
on page 181 for more information.
1 Slide the battery into the radio frame until the side latches click into place.
23
English
24
English
A
2 To remove the battery, squeeze the release latches at the bottom of the battery until the battery releases from the radio and remove the battery from the radio.
Note: When removing the battery, ensure that the radio is turned off.
Attaching the Antenna
Ensure the radio is turned off before attaching the antenna.
1 Set the antenna in its receptacle.
2 Turn the antenna clockwise to attach to the radio.
3 To remove the antenna, turn the antenna counterclockwise.
Note: When removing the antenna, ensure that the radio is turned off.
Removing and Attaching the Accessory
Connector Cover
The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio.
Note: To prevent damage to the connector, shield it with the connector cover when not in use.
1 To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio.
Note: If the thumbscrew is too tight, use an Allen wrench at to loosen it first.
A
B
C
2 Rotate and lift the connector cover to disengage it from the radio.
English
25
3 To attach the accessory connector cover, insert the hooked end of the cover into the slot above the connector.
4 Press downward on the cover’s top to seat it in the slot.
5 Once in place, tighten by rotating the thumbscrew
clockwise by hand.
Using the Carry Holder
1 Position the radio within the carry holder with the main speaker facing outward.
2 Slide the radio down into the carry holder until it clicks in place.
26
English
3 To remove the radio from the carry holder, place the tip of your fingers on the ledge of the carry holder.
4 Push at the bottom of the radio until the radio is released from it.
English
27
Turning On the Radio
1 Rotate the On/Off/Volume Control Knob clockwise until you hear a click.
• If the power-up test is successful, you see momentary SELFTEST on the radio display, followed by the Home screen.
• If the power-up test is unsuccessful, you see
Error XX/YY
(XX/YY is an alphanumeric code).
Note: If the radio fails to power-up after repeating a few times, record the Error XX/YY code and contact your dealer.
2 To turn off the radio, rotate the On/Off/Volume
Control Knob counterclockwise until you hear a click.
28
English
A
Adjusting the Volume
Ensure the radio is power on and the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises.
1 To increase the volume, rotate the On/Off/Volume
Control Knob clockwise.
2 To decrease the volume, rotate this knob counterclockwise.
English
29
Identifying Radio Controls
Radio Parts and Controls
1
2
3
4
5
14
13
12
11
10
6
9
8
7
30
English
15
16
23
17
22
18
1
2
3
4
19
20
21
Antenna
LED
Top (Orange) Button
[1]
Microphone
26
25
24
7
8
5
6
Accessory Connector
Home Button
4–Way Navigation Button
Keypad
9 Data Feature Button
10 Menu Select Buttons
11 Main Display
12 Secondary Speaker
13 2–Position Concentric Switch
[1]
14 3–Position A/B/C Switch
[1]
15 On/Off/Volume Control Knob
16 Top Side (Select) Button
[1]
17 Push-to-Talk (PTT) Button
18 Side Button 1
[1]
19 Side Button 2
[1]
20 Battery Latch
1
These radio controls/buttons are programmable.
21 Battery
22 Main Speaker
23 Microphone
24 Bluetooth Pairing Location Indicator
25 Top Display
26 16–Position Select Knob
[1]
Programmable Features
Any reference in this manual to a control that is preprogrammed means that the control must be programmed by a dealer or qualified radio technician using the radio programming software, in order to assign a feature to that control.
The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:
Press
Pressing and releasing rapidly.
English
31
32
Long Press Pressing and holding for the preprogrammed duration (between
0.25 seconds and 3.75 seconds).
Hold down Keeping the button pressed.
Assignable Radio Functions
Bluetooth On/Off Allows you to turn on/off the
Bluetooth.
Bluetooth
Configuration
Allows you to access to the
Bluetooth menu.
Bluetooth Audio
Reroute
Allows you to toggle the audio route between radio speaker or
Remote Speaker Microphone and Bluetooth headset.
Bluetooth
Headset PTT
Bluetooth Data
Devices
Bluetooth Clear
All Pairing
Keys up the Bluetooth Headset microphone.
Keys up the Bluetooth data devices.
Allows you to clear all pairing information for Bluetooth. This is accessed by a long press of the Bluetooth On/Off Button.
English
Bluetooth Inquiry
On/Off
Bluetooth
Discoverable
On/Off
Call Alert
Call Response
Channel
Contacts
Dynamic ID
(Conventional
Only)
Dynamic Priority
(Conventional
Only)
Enables Bluetooth Search feature.
Enables Bluetooth visibility.
This is accessed by a long press of the Bluetooth Inquiry
On/Off Button.
Allows the radio to function like a pager, or to verify if a radio is active on the system.
Allows you to answer a private call.
Selects a channel.
Selects the Contacts menu.
Allows you to edit the ASTRO
Individual ID and/or MDC
Primary ID of the radio.
Allows any channel in a Scan
List (except for the Priority-One channel) to temporarily replace the Priority-Two channel.
Emergency
Information
Internet Protocol
Address
Location
Depending on the programming, initiates or cancels an emergency alarm or call.
Displays the information of the radio.
Display the Internet Protocol
(IP) address, device name and status of the radio.
Determines the current location
(latitude, longitude, time and date), and also the distance and bearing to another location.
Or, turns the GPS functionality on or off for all locations.
LTE On/Off
Press this button to enter LTE screen; long-press this button to toggle LTE module on or off.
Man Down Clear
Clears the alarm of Man Down mode which was triggered when your radio achieves or passes a tilt angle threshold or a combination of the angle
Message
Mode Select
threshold and a motion sensitivity level.
Enters the current message list.
Long-press programs a button with the current zone and channel of the radio; once programmed, the short-press of that button changes the radio zone channel to the programmed zone and channel.
Monitor
(Conventional
Only)
Multiple Private
Line
(Conventional
Only)
Monitors a selected channel for all radio traffic until function is disabled.
Selects the Multiple Private
Line lists.
Nuisance Delete
Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel from the scan list.
English
33
34
English
One Touch 1– 4
Launches a specific feature with one single button-press.
You can setup as many as four separately programmed buttons for four different features.
Phone
Allows you to make and receive calls similar to standard phone calls.
Private Call
(Trunking Only)
Private Line
Defeat
(Conventional
Only)
Query
Allows a call from an individual radio to another individual radio.
Overrides any coded squelch
(DPL or PL) that is preprogrammed to a channel.
Radio Profiles
Launches a list of predefined short text messages only after successfully logged in the two-
Factor Authentification.
Allows easy access to a set of preprogrammed visual and audio settings of the radio.
Recent Calls
Allows easy access to the list of calls recently received or made.
Rekey Request
Notifies the dispatcher you want a new encryption key.
Allows user to manually send a repeater access codeword.
Repeater Access
Button (RAB)
(Conventional
Only)
Reprogram
Request
(Trunking Only)
Request-To-Talk
(Conventional
Only)
Notifies the dispatcher you want a new dynamic regrouping assignment.
Notifies the dispatcher you want to send a voice call.
Scan
Scan List
Programming
Secure
Transmission
Select
(Conventional and Trunking)
Toggles scan on or off.
Selects the scan list for editing
(by long press on the Scan button).
Toggles the Secure
Transmission On or Off when the Secure/Clear Strapping fields is set to Select for the
Selective Call
(Conventional
Only)
Site Display/
Search (Trunking
Only)
current channel and when the radio is model/option capable.
Calls an assigned radio.
Displays the current site ID and
RSSI value; performs site search for Automatic Multiple
Site Select (AMSS) or
SmartZone operation.
Locks onto a specific site.
Site Lock/Unlock
(Trunking Only)
Status (Astro 25
Trunking Only)
Talkaround/
Direct
(Conventional
Only)
Talkgroup
(Conventional
Only)
Sends data calls to the dispatcher about a predefined status.
Toggles between using a repeater and communicating directly with another radio.
Allows a call from an individual radio to a group of radios.
Text Messaging
Service (TMS)
Selects the text messaging menu.
TMS Quick Text
Selects a predefined message.
User
Automatically registers with the server.
Zone Select
Enhanced Zone
Bank
Allows selection from a list of zones.
Basic Zone Bank Provides access from up to 6 zones by toggling between 2 banks of 3 zones, one group of
3 (A, B and C) to a second group of 3 zones (D, E and F).
Provides access from up to 75 zones by toggling between 25 banks (A, B ... X or Y) of 3 zones.
Assignable Settings or Utility Functions
Keypad/Controls
Lock
Locks or unlocks the keypad, programmable buttons, switches or rotary knobs.
English
35
Light/Flip
TX Power Level
Press the button to toggle the display backlight on or off; press and hold the button to reverse the content of the top display.
Toggles transmit power level between high and low.
Voice
Announcement
Audibly indicates the current feature mode, Zone or
Channel the user has just assigned.
Voice Mute
Toggles voice mute on or off.
Volume Set Tone
Sets the volume set tone.
36
Accessing the Preprogrammed Functions
You can access various radio functions through one of the following methods.
• A short or long press of the relevant programmable buttons.
• Use the Menu Select Button.
• Use the Menu Select and Navigation buttons.
English
A
B
E
C
D
C
D
A
B
E
Softkeys
Menu Select Buttons
Data Feature Button
4–Way Navigation Button
Home Button
Menu Select Buttons
Note: Check with your dealer or system administrator for the list of features activated in your radio.
Use the Menu Select button to access the menu entry of your radio feature. Your radio may be preprogrammed differently from the following
example, but the steps for selecting a channel may appear as shown below:
Press the Menu Select button directly below Chan.
Home Button
Pressing the button returns you to the Home
(default) screen. In most cases, this is the current mode. For selected radio features, the button is also used to save user-edited radio settings or information before returning you to the Home screen.
Note: Some features do not require you to press to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information.
4-Way Navigation Button
Use the 4-Way Navigation Button to scroll up, down, left or right with one of the following methods.
• Press and release one of the button to scroll from one entry to the next one.
• Press and hold one of the button to have the radio toggles through the list automatically (release the button to stop).
Data Feature Button
Use Data Feature button to access data-related features, such as the Text Messaging Service (TMS) feature screen.
Keypad
You can use the 3 x 4 alphanumeric keypad to access your radio features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The following tables show the number of times a key needs to be pressed to generate the required character.
English
37
38
Keypad Characters – Uppercase Mode
Key Number of Times Key is Pressed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 .
, ?
!
; @ _ * # & $ / + = \ “ ‘ ( )
A B C
D E F
G H I
J K L
M N O
P Q R S
T U V
W X Y Z
Toggle between mixed case mode, uppercase mode and lowercase mode.
Space
Toggle between numeric and letter mode.
English
Keypad Characters – Lowercase Mode
Key Number of Times Key is Pressed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 .
, ?
!
; @ _ * # & $ / + = \ “ ‘ ( ) a b c d e f j g h i k l m n o p q r s t u v w x y z
Toggle between mixed case mode, uppercase mode and lowercase mode.
Space
Toggle between numeric and letter mode.
English
39
40
Keypad Characters – Numeric Mode
Key Number of Times Key is Pressed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 .
, ?
!
; @ _ * # & $ / + = \ “ ‘ ( )
2
3
6
7
4
5
8
9
0
Space
Toggle between numeric and letter mode.
English
Keypad Characters – Hexadecimal Mode
Key Number of Times Key is Pressed
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
1
2 A B C
3 D E F
6
7
4
5
8
9
0
Not applicable
Not applicable
English
41
Push-To-Talk (PTT) Button
A
The PTT button on the side of the radio serves two basic purposes:
• While a call is in progress, the PTT button allows the radio to transmit to other radios in the call.
Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed.
• While a call is not in progress, the PTT button is used to make a new call. See
on page 64 for more information.
42
English
Identifying Status Indicators
Status Icons
The 240 x 320 pixel front liquid crystal display (LCD) of your radio shows radio status, text entries, and menu entries. The top two display rows contain color icons that indicate radio operating conditions.
Selected icons are also shown on the first row of the
112 x 32 pixel top monochrome display screen of your radio. The following icons are for the front display screen unless indicated otherwise.
Receiving
Radio is receiving a call or data.
Top
Display:
Top
Display:
Transmitting
Radio is transmitting a call or data.
Top
Display:
Call Received
Radio has received an Individual Call.
Battery
For IMPRES battery operation only – the icon shown indicates the charge remaining in the battery.
For all battery operation – the icon blinks when the battery is low.
Top
Display:
Received Signal Strength Indicator
(RSSI)
The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal.
Roaming
The radio has roamed to and is currently registered to a foreign system.
43
English
Top
Display:
44
English
Top
Display:
Top
Display:
Direct
On – Radio is currently configured for direct radio-to-radio communication
(during conventional operation only).
Off – Radio is connected with other radios through a repeater.
Monitor (Carrier Squelch)
Selected channel is being monitored
(during conventional operation only).
In-Call User Alert
On – The feature is enabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is activated.
or
Top
Display:
or
Off – The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is deactivated.
Power Level
L – Radio is set at Low power.
H – Radio is set at High power.
Top
Display:
Scan
Radio is scanning a scan list.
Top
Display:
Priority Channel Scan
Blinking dot – Radio detects activity on channel designated as Priority-One.
Steady dot – Radio detects activity on channel designated as Priority-Two.
Top
Display:
Top
Display:
View/Program Mode
Radio is in the view or program mode.
On steady – View mode
Blinking – Program mode
Vote Scan Enabled
The vote scan feature is enabled.
Top
Display: or
or
Top
Display: or
or
Basic Zone Bank 1
A – Radio is in Zone 1.
B – Radio is in Zone 2.
C – Radio is in Zone 3.
Basic Zone Bank 2
D – Radio is in Zone 4.
E – Radio is in Zone 5.
F – Radio is in Zone 6.
Top
Display:
, or
, until
Enhanced Zone Bank
A – Contains Zone 1, Zone 2 and Zone
3,
B – Contains Zone 4, Zone 5 and Zone
6,
C – Contains Zone 7, Zone 8 and Zone
9, until
X – Contains Zone 70, Zone 71 and
Zone 72,
Y – Contains Zone 73, Zone 74 and
Zone 75.
Top
Display:
Secure Operation
On
Off
Secure operation.
Clear operation.
Blinking Receiving an encrypted voice call.
English
45
46
English
AES Secure Operation
On – AES secure operation.
Off – Clear operation.
Blinking – Receiving an encrypted voice call.
GPS Signal
On – Feature is enabled and signal is available.
Off – Feature is disabled.
Blinking – Feature is enabled, but no signal is available.
User Login Indicator (IP Packet Data)
On – User is currently associated with the radio.
Off – User is currently not associated with the radio.
Blinking – Device registration or user registration with the server failed due to an invalid username or pin.
Inverted – User successfully login to the secured IP Packet Data.
Data Activity
Data activity is present.
Hexadecimal
Indicates that the text entry is currently in hexadecimal mode.
Numeric
Indicates that the text entry is currently in numeric mode.
Start Case
Indicates that the first character of the text entry is capitalized.
Mixed Case
Indicates that the text entry is currently in normal text mode.
Uppercase
Indicates that the text entry is currently in uppercase mode.
Lowercase
Indicates that the text entry is currently in lowercase mode.
Lowercase Predictive
Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen.
Mixedcase Predictive
Indicates that the text entry is currently in mixed case and with predicted words shown at the bottom of the screen.
Uppercase Predictive
Indicates that the text entry is currently in uppercase and with predicted words shown at the bottom of the screen.
Top
Display:
Bluetooth On
Bluetooth is on and ready for Bluetooth connection.
Top
Display:
Bluetooth Connected
Bluetooth is currently connected to the external Bluetooth device.
LTE network is active
LTE system is available and connected.
LTE Receiving
The radio is receiving LTE signal.
LTE Transmitting
English
47
48
English
The radio is transmitting LTE signal.
LTE Receiving and Transmitting
The radio is receiving and transmitting
LTE signal.
LTE with ARS User logged in
Indicating ARS user logged in successfully with LTE system.
LTE Receiving while ARS user logged in
Indicating ARS user logged in successfully with LTE system.
LTE Transmitting while ARS user logged in
The radio is transmitting LTE signal with
ARS user logged in.
LTE Receiving and Transmitting while
ARS user logged in
Blinking
The radio is receiving and transmitting
LTE signal with ARS user logged in.
LTE icon is Blinking
ARS user login failed while in LTE system.
Text Messaging Service (TMS) Indicators
This feature allows you to send and receive text messages. Status icons and menu options shown here help you to work more efficiently with TMS
on page
102 for more information.
TMS Status Icons
The following icons appear on the radio’s display when you send and receive text messages.
Inbox Full
The Inbox is full.
Message Sent
The text message is sent successfully.
Message Unsent
The text message cannot be sent.
Unread Message
• User receives a new message.
• The selected text message in the Inbox has not been read.
Read Message
The selected text message in the Inbox has been read.
Normal Message
User is composing a message with normal priority and without a request for a reply.
Message Index
Indicates the index of the current message the user is viewing.
Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column.
Priority Status
• The “Priority” feature is toggled on before the message is sent.
• Messages in the Inbox folder are flagged with “Priority”.
Request Reply
• The “Request Reply” feature is toggled on before the message is sent.
• Messages in the Inbox folder are flagged with “Request Reply”.
Priority Status and Request Reply
• User is composing a message with a priority status and a request for a reply.
• Messages in the Inbox folder are flagged with “Priority” and “Request
Reply”.
English
49
TMS Menu Options
Menu
Option
Back
Clr
Del
Edit
Exit
No
Optn
Rply
Sel
Send
Yes
Description/Function
Brings you back to the previous screen.
Deletes all messages.
Deletes a message or text.
Brings you to the edit screen.
Exits to the Home screen.
Returns to the previous screen.
Brings you to the Options main screen.
Replies to a message.
Selects the highlighted command.
Sends the message.
Updates or saves a command.
50
Call Type Icons
The following icons appear on the radio’s main display, when you make or receive a call, or view
English selected call lists, to indicate the different call types associated with an alias or ID.
Radio number.
Radio number added to a Call List.
Mobile number.
Mobile number added to a Call List.
Landline phone number.
Landline phone number added to a Call
List.
Incoming call or data.
Outgoing call or data.
Incoming emergency call.
LED Indicator
The LED indicator shows the operational status of your radio.
A
Solid red
Blinking red
Double blinking red
Rapidly blinking red
Radio is transmitting.
Radio is transmitting at low battery condition.
Radio is in Emergency Mode.
Radio has failed the self test upon powering up or encountered a fatal error.
Solid yellow
(Conventional
Only)
Blinking yellow
Channel is busy.
Solid green
Blinking green
Rapidly blinking green
Radio is receiving a secured transmission.
Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode.
Radio is receiving an individual or telephone call, or is on a
Priority-Two channel while in the Scan List Programming mode.
Radio is on a Priority-One channel while in the Scan List
Programming mode.
Note: No LED indication when the radio receives a clear (non-secured) transmission in trunking Mode.
LED indication can be preprogramed by qualified technician to be permanently disabled. Consult your dealer for further details if you want to disable it.
English
51
Intelligent Lighting Indicators
This feature temporarily changes the backlight of the top display screen, and adds a color bar to the main display screen to help signal that a radio event has occurred.
Note: This feature must be preprogrammed by a qualified radio technician.
Backlight and Bar
Color
Orange
Notification
Emergency Alerts
Red Critical Alerts
Call Alerts
When
The radio initiates an emergency alarm or call.
The radio receives an emergency alarm or call.
The radio initiates the Man Down Post-Alert timer.
The radio initiates Fireground Evacuation alarm.
The radio battery is low.
The radio is out of range.
The radio enters Failsoft mode.
The radio is unable to establish a full connection with the system.
The radio is unable to authenticate or register with the system.
The radio lost GPS signal or GPS function fails.
The radio receives a private call.
52
English
Green
Backlight and Bar
Color
Notification When
The radio receives a phone call.
The radio receives a call alert.
The radio receives a selective call.
The radio enters Geofence.
Alert Tones
Your radio uses alert tones to inform you of your radio’s condition. The following table lists these tones and when they occur.
You Hear
Short, Low-
Pitched Tone
Tone Name
Radio Self Test Fail
Reject
Time-Out Timer Warning
No ACK Received
Individual Call Warning
Tone
Man Down Entry
Heard
When radio fails its power-up self test.
When an unauthorized request is made.
Four seconds before time out.
When radio fails to receive an acknowledgment.
When radio is in an individual call for greater than 6 seconds without any activity.
When radio initiates Man Down mode.
English
53
54
English
You Hear
Long, Low-
Pitched Tone
Tone Name Heard
Time-Out Timer Timed Out
After time out.
Talk Prohibit/PTT Inhibit
(When PTT button is pressed) transmissions are not allowed.
Lack of Voice PTT Time out When the radio ends your call after it detected there are lack of voice for 5 seconds after the PTT is pressed and hold. Your radio ends the call to enable your radio to receive calls from other radio users.
Out of Range
(When PTT button is pressed) the radio is out of range of the system.
Invalid Mode
Busy
When radio is on an unpreprogrammed channel.
When system is busy.
A Group of
Low-Pitched
Tones
Short, Medium-
Pitched Tone
Valid Key-Press
Radio Self Test Pass
When a correct key is pressed.
When radio passes its power-up self test.
Clear Voice
At beginning of a non-coded communication.
Priority Channel Received
When activity on a priority channel is received.
Emergency Alarm /Call
Entry
When entering the emergency state.
You Hear
Long, Medium-
Pitched Tone
A Group of
Medium-
Pitched Tones
Tone Name
Central Echo
Volume Set
Emergency Exit
Failsoft
Automatic Call Back
Keyfail
Console Acknowledge
Received Individual Call
Call Alert Sent
Site Trunking
Low-Battery Chirp Short, High-
Pitched Tone
(Chirp)
Two HIgh-
Pitched Tones
Ringing
GPS Fails
Fast Ringing
Heard
When central controller has received a request from a radio.
When volume is changed on a quiet channel.
When exiting the emergency state.
When the trunking system fails.
When voice channel is available from previous request.
When encryption key has been lost.
When status, emergency alarm, or reprogram request ACK is received.
When Call Alert or Private Call is received.
When Call Alert is received by the target radio.
When a SmartZone trunking system fails.
When battery is below preset threshold value.
When the GPS signal is lost or when GPS fails.
When system is searching for target of Private Call.
English
55
You Hear
Gurgle
Tone Name
Enhanced Call Sent
Phone Call Received
Dynamic Regrouping
Talk Permit
56
English
Unique, Low-
Pitched Chirp
Unique, High-
Pitched Chirp
Incremental-
Pitched Tone
New Message
Priority Status
Decremental-
Pitched Tone
A Group of
Very High-
Pitched Tones
Bluetooth Paired
Bluetooth Connected
Bluetooth Unpaired
Bluetooth Disconnected
Man Down Continuous
Tone
Critical Man Down
Continuous Tone
Heard
When waiting for target of Private Call to answer the call.
When a land-to-mobile phone call is received.
(When PTT button is pressed) a dynamic ID has been received.
(When PTT button is pressed) is verifying with the system for accepting its transmissions.
When a new message is received.
When a priority message is received.
When Bluetooth accessory is paired with the radio.
When Bluetooth accessory is connected to the radio.
When Bluetooth accessory is unpaired from the radio.
When Bluetooth accessory is disconnected from the radio.
When radio is in Man Down mode and prepares to transmit
Emergency Alarm when the timer of this alarm ends.
When radio is in Man Down Enhanced mode and prepares to transmit Emergency Alarm when the timer of this alarm ends.
You Hear
Unique Low-
High Tone
Unique High-
Low Tone
Tone Name
Enhanced Zone Bank Up
Heard
When EZB Up button is pressed to scroll the Enhance Zone
Bank up.
Enhanced Zone Bank Down When EZB Down button is pressed to scroll the Enhance Zone
Bank down.
Phone Call Displays and Alerts
The following phone call displays and alerts appears on the radio’s display when you make and receive Phone calls.
The radio also uses alert tones to indicate the current status.
You Hear
A Long Tone
You See
No phone
Phone busy
When
You press the PTT button and the phone system is not available.
The phone system is busy.
Notes
Press to hang up. The radio returns to the
Home screen.
A Busy Tone
–
Phone busy
No acknowledge
When a channel is not available.
The call is not acknowledged.
Press to exit the phone mode and try your call later.
The radio automatically connects when a channel opens.
Press to hang up. The radio returns to the
Home screen.
English
57
58
English
You Hear
A High- Pitched
Tone
You See
–
When
When you release the PTT button.
Notes
The radio indicates to the landline party that he or she may begin talking.
Note: You have the option of sending additional digits (overdial), such as an extension number, or credit card or PIN numbers, to the phone system. If the radio is preprogrammed for live overdial, every digit entered after the call is connected is sent to the phone system.
If the radio is preprogrammed for buffered overdial, the digits pressed are entered into memory and then sent when the PTT button is pressed. Press the PTT button to send either digits or voice, but not both at the same time.
General Radio Operation
Selecting a Zone
Your radio must be preprogrammed to allow you to use this feature.
A zone is a group of channels. The following methods are options on how to select a radio zone. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Select a zone via the preprogrammed Zone (3-
Position A/B/C) switch: a) Move the preprogrammed Zone (3-Position
A/B/C) switch to the position of the required zone.
If the zone number entered is unprogrammed, the display shows Invalid entry. Repeat this step.
b) Press the Menu Select button directly below
Sel
to confirm the displayed zone.
c) Press the PTT button to transmit on the displayed zone channel.
• Select a zone via the radio menu Zone: a) or to Zone and press the Menu Select button directly below Zone.
b) or to the required zone, or use the keypad to enter the zone number.
If the zone number entered is unprogrammed, the display shows Invalid entry. Repeat this step.
c) Press the Menu Select button directly below
Sel
to confirm the displayed zone.
d) Press the PTT button to transmit on the displayed zone channel.
• Select a zone via the radio menu ZnUp or ZnDn: a) or to ZnUp or ZnDn.
b) Press and hold the Menu Select button directly below ZnUp or ZnDn until the required zone appears.
Positions of ZnUp and ZnDn on the display may differ each time you release the Menu Select button. Read carefully before you press.
c) Press the PTT button to transmit on the displayed zone channel.
English
59
60
Selecting a Radio Channel
A channel is a group of radio characteristics, such as transmit/ receive frequency pairs. The following methods are options on how to select a radio channel. The result of all the methods is the same.
You can use the options interchangeably depending on your preference and the programmed functions.
• Select a channel via the preprogrammed 16–
Position Select Knob to the desired channel.
a) Rotate the preprogrammed 16–Position
Select Knob to the desired channel.
b) Press the PTT button to transmit on the displayed zone channel.
• Select a channel via the radio menu Chan: a) or to Chan.
b) Press the Menu Select button directly below
Chan
.
c) or to the required channel or use the keypad to enter the channel number.
If the channel number entered is unprogrammed, the display shows Invalid entry
. Repeat this step.
English d) Press the Menu Select button directly below
Sel
to confirm the selected channel.
e) Press the PTT button to transmit on the displayed zone channel.
• Select a channel via the radio menu Channel Up or Channel Down: a) or to ChUp or ChDn.
b) Press the Menu Select button directly below
ChUp
or ChDn.
Positions of ChUp and ChDn on the display may differ each time you release the Menu Select button. Read carefully before you press.
c) Press the PTT button to transmit on the displayed zone and channel.
Selecting a Channel via Channel Search
Button
This feature allows you to do a quick search for a specific channel in your radio by keying in the alias of the channel. If the name matches, your radio prompts the first found matched channel name.
1 Perform one of the following actions:
•
• Press the preprogrammed Channel Search button.
or to CSrh and press the Menu Select button directly below CSrh.
A blinking cursor appears on the Channel Search screen.
2 Use the keypad to type or edit your channel name.
3 To initiate searching, press the Menu Select button directly below CSrh once the entry is done.
To exit this procedure, press the Menu Select button directly below Cncl.
The display shows Searching. Once found, the display shows the matched channel name and the radio changed its transmission to the selected channel.
If the radio is triggered to search for an empty entry,
the display shows Invalid entry. Repeat step
search again.
If the entry does not match, the display shows
Channel name not found
again; or press or the Menu Select button directly below Exit to exit.
Mode Select Feature
Mode Select allows a long press to save the current zone and channel of your radio to a programmable button, keypad button, or a softkey; then once programmed, the short-press of that button or softkey changes the transmission to the saved zone and channel.
There are two methods to save the selected zone and channel:
• Softkeys
• Programmable buttons and keypad buttons (digit 0 to 9)
Note: Your radio must be preprogrammed to allow you to use this feature.
Saving a Zone and a Channel to a Softkey
Five softkeys are available for you to save the frequently used zone and channel.
1 Toggle your zone and channel to the required zone and channel.
61
English
62
2
or to MS1, MS2 ... or MS5.
3 Press and hold the Menu Select button directly below one of the softkey (MS1 – MS5).
You hear a short, medium-pitched tone when the zone and channel is saved.
Note: To change the programmed zone and channel, repeat this procedure.
Short press of the programmed softkey changes your current transmission to the zone and channel programmed in this softkey.
Saving a Zone and a Channel to a Button
You can save the frequent used zone and channel to the programmable buttons and keypad digit 0 to 9 buttons.
1 Toggle your zone and channel to the required zone and channel.
2 Press and hold the button you desire to program.
You hear a short, medium-pitched tone when the zone and channel is saved.
Note: Repeat this procedure to change the zone and channel of the programmed button. Short press of the programmed button
Short press of the programmed button changes your current transmission to the zone and channel programmed in this button.
Receiving and Responding to a Radio Call
Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls.
A
The LED lights up solid red while the radio is transmitting. In conventional mode, the LED lights up solid yellow when the radio is receiving a transmission. In trunking mode, there is no LED indication when the radio receives a transmission.
English
If the radio is receiving a secure transmission, the
LED blinks yellow.
Receiving and Responding to a Talkgroup Call
To receive a call from a group of users, your radio must be configured as part of that talkgroup.
When you receive a talkgroup call (while on the
Home screen) the radio triggers for your attention with one of the following scenarios depending on the system your radio is configured:
• For ASTRO Conventional system, the LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID.
• For Trunking system, the display shows the caller alias or ID.
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
2 Press the PTT button to respond to the call.
The LED lights up solid red.
3 Release the PTT button to listen.
details on making a Talkgroup Call.
Receiving and Responding to a Private Call (Trunking
Only)
A Private Call is a call from an individual radio to another individual radio.
The one-to-one call between the two radios are not heard by the others in the current talkgroup. The transmitting radio automatically verifies that the receiving radio is active on the system and can display the caller ID.
Note: With the inactivity timer enabled (optional), when there is no response from the receiving radio, the transmitting radio exits the call with Menu Inactive
Exit tone after the timer expires.
When you receive a Private Call, you hear two alert tones and the LED blinks green. The display shows
Call received
and the call received icon blinks.
1 Perform one of the following actions:
• Press the Menu Select button directly below
Resp
.
• Press theCall Response button within 20 seconds after the call indicators begin.
If the caller alias is in the call list, the display shows the caller alias during the call.
63
English
If the caller name is not in the call list, the display shows the caller ID.
2 Press and hold the PTT button to talk. Release the
PTT button to listen.
3 Press or the Call Response button to hang up and return to the Home screen.
64
Making a Private Call (Trunking Only)
on page 65 for details on making a Private Call.
Receiving and Responding to a Telephone Call
(Trunking Only)
This feature allows you to receive calls similar to standard phone calls from a landline phone.
Note: With the inactivity timer enabled (optional), if there is no response to the call after the timer expires, your radio exits the call with Menu Inactive Exit tone.
When you receive a Telephone Call, you hear telephone-type ringing and the LED blinks green. The display shows Phone Call and the call received icon blinks.
1 Press the Call Response button within 20 seconds after the call indicators begin.
2 Press and hold the PTT button to talk. Release the
PTT button to listen.
3 Press or the Call Response button to hang up and return to the Home screen.
Making a Telephone Call (Trunking Only)
on page 67 for details on making a Telephone Call.
Making a Radio Call
You can select a zone, channel, subscriber ID, or talkgroup by using:
• The preprogrammed Zone switch.
• The 16-Position Select Channel Knob.
• A preprogrammed One Touch Call button.
• The Contacts list (see
on page 82).
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu
Inactive Exit Tone upon feature exit.
English
Making a Talkgroup Call
To make a call to a group of users, your radio must be configured as part of that talkgroup.
1 Turn the 16-Position Select Channel Knob to select the channel with the desired talkgroup.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
3 Press the PTT button to make the call.
The radio shows different indicators based on the system the radio is configured.
• For ASTRO Conventional system, the LED lights up solid red. The display shows the talkgroup alias or ID.
• For Trunking system, the LED lights up solid red.
4 Speak clearly into the microphone.
5 Release the PTT button to listen.
Making a Private Call (Trunking Only)
Your radio must be preprogrammed to allow you to use this feature.
This feature allows you to send an individual Call
Alert or page if there is no answer from the target radio.
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed Quick
Access (One-Touch) Private Call button to dial the preprogrammed ID (number) and initiate the Private Call. Proceed to step
.
• To access this feature via the menu, proceed to the next step.
2
or to Call, and press the Menu Select button directly below Call.
The display shows the last transmitted or received
ID.
3 To select the required ID, perform one of the following actions:
• Press the Menu Select button directly below
Cnts
to scroll through and select the required
ID.
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
65
English
• or to the required ID.
• Use the keypad to enter the required ID.
4 Press the PTT button to initiate the Private Call.
The display shows Calling... <Number>.
5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
When you are connected, the display shows the
ID of the target radio.
If no acknowledgment is received, the display shows No acknowledge.
6 Press and hold the PTT button to talk. Release the
PTT button to listen.
7 Press to return to the Home screen.
66
Making an Enhanced Private Call (Trunking Only)
Your radio must be preprogrammed to allow you to use this feature.
This feature allows you to send an individual Call
Alert Page if there is no answer from the target radio.
on page 86 for more information.
English
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed Quick
Access (One-Touch) Enhanced Private Call
button to dial the preprogrammed ID (number)
and initiate the Private Call. Proceed to step
.
• To access this feature via the menu, proceed to the next step.
2
or to Call, and press the Menu Select button directly below Call.
The display shows the last transmitted or received
ID.
3 To select the required ID, perform one of the following actions:
• Press the Menu Select button directly below
Cnts
to scroll through and select the required
ID.
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
• or to the required ID.
• Use the keypad to enter the required ID.
4 Press the PTT button to initiate the Private Call.
The display shows Calling... <Number>.
5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
When you are connected, the display shows the
ID of the target radio.
If no acknowledgment is received, the display shows No acknowledge.
If the target radio does not respond before the time out, the display shows No answer.
6 Press and hold the PTT button to talk. Release the
PTT button to listen.
7 Press to return to the Home screen.
Making a Telephone Call (Trunking Only)
This feature allows you to make calls similar to standard phone calls to a mobile or landline phone.
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed Quick
Access (One-Touch) Phone Call button to dial the preprogrammed phone number.
• To access this feature via the menu, proceed to the next step.
2
or to Phon, and press the Menu Select button directly below Phon.
The display shows the last transmitted or received
ID.
3 To select the required ID, perform one of the following actions:
• Press the Menu Select button directly below
Cnts
to scroll through and select the required
ID.
•
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
or to the required phone number.
• Use the keypad to enter the required phone number.
4 Press the PTT button to dial the phone number.
5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
67
English
68
6 When your call is answered, press and hold the
PTT button to talk. Release the PTT button to listen.
7 Press to return to the Home screen.
Phone Call Displays and Alerts
on page 57 for more information if your call is NOT answered.
Switching Between Repeater or Direct
Operation Button
The Repeater Operation increases the radio’s range by connecting with other radios through a repeater.
The transmit and receive frequencies are different.
The Direct or “talkaround operation” allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same.
Perform one of the following actions:
• Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes.
•
or to Dir and press the Menu Select button directly below Dir.
The display shows Repeater mode if the radio is currently in Repeater mode.
The display shows Direct mode and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only).
Monitor Feature
Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case.
This digital technology quiets the transmission by removing the noise from the signal and allows only the clear voice or data information to be heard.
Use the Monitor feature to make sure a channel is clear before transmitting.
Monitoring a Channel
The following methods are options on how to monitor a channel. The result of all the methods is the same.
English
You can use the options interchangeably depending on your preference and the programmed functions.
• Monitoring a Channel with Volume Set button.
a) Select the desired zone and channel.
b) Press and hold the Volume Set button to hear the volume set tone.
c) Adjust the Volume Control Knob if necessary.
d) Release the Volume Set button.
e) Press and hold the PTT button to transmit.
The LED lights up solid red.
f) Release the PTT button to receive (listen).
• Monitoring a Channel with Monitor button.
a) Press the preprogrammed Monitor button.
b) Adjust the Volume Control Knob if necessary.
c) Press and hold the PTT button to transmit.
The LED lights up solid red.
d) Release the PTT button to receive (listen).
The Carrier Squelch indicator appears on the display when you monitor a channel via the preprogrammed Monitor button.
• Monitoring a Channel via the selected zone channel.
a) Select the desired zone and channel.
b) Listen for a transmission.
c) Adjust the Volume Control Knob if necessary.
d) Press and hold the PTT button to transmit.
The LED lights up solid red.
e) Release the PTT button to receive (listen).
Monitoring Conventional Mode
Your radio may be preprogrammed to receive Private-
Line
®
(PL) calls.
1 Momentarily press the Monitor button to listen for activity.
The Carrier Squelch indicator appears on the display.
2 Press and hold the Monitor button to set continuous monitor operation.
The duration of the button press is programmable.
3 Press the Monitor button again, or the PTT button, to return to the original squelch setting.
If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button.
69
English
Advanced Features
70
Advanced Call Features
Selective Call (ASTRO Conventional Only)
This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you.
Receiving a Selective Call
When you receive a Selective Call, the radio initiates for your attention with one of the following indication scenario:
• You hear two alert tones and the LED lights up solid yellow to indicate the transmitting radio is still sending signal. The call received icons blinks and the display shows Call received.
• The LED blinks solid green once to indicate the transmitting radio is pending to receive signal.
The speaker unmutes.
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
English
2 Press and hold the PTT button to talk. Release the
PTT button to listen.
Making a Selective Call
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed Quick
Access (One-Touch) Selective Call button to
dial the preprogrammed ID. Proceed to step
.
• To access this feature via the menu, proceed to the next step.
2
or to Call, and press the Menu Select button directly below Call.
The display shows the last transmitted or received
ID.
3 To select the required ID, perform one of the following actions:
• Press the Menu Select button directly below
Cnts
to scroll through and select the required
ID.
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
• or to the required ID.
• Use the keypad to enter the required ID.
4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
5 Press and hold the PTT button to start the
Selective Call.
The display shows the ID of the target radio.
6 Release the PTT button to listen.
7 Press to return to the Home screen.
Talkgroup Call Feature (Conventional Operation Only)
This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel.
Note: Encryption keys are associated to talkgroups.
When talkgroups are associated, encryption keys are changed by changing the active talkgroup. See
information.
Selecting a Talkgroup
1
or to Tgrp and press the Menu Select button directly below Tgrp.
The display shows the last Talkgroup that was selected and stored.
2 Perform one of the following actions:
•
•
or to Preset for the preset preprogrammed Talkgroup.
or to the required Talkgroup.
• Use the keypad to enter the number of the corresponding Talkgroup in the list.
3 Press the Menu Select button directly below Sel to save the currently selected Talkgroup and return to the Home screen.
If the encryption key associated to the new
Talkgroup is erased, you hear a momentary key fail tone and the display shows Key fail.
If the encryption key that is associated to the new
Talkgroup is not allowed, you hear a momentary key fail tone and the display shows Illegal key.
4 Press to return to the Home screen.
71
English
Sending a Status Call
This feature allows you to send data calls to the dispatcher about a predefined status.
Each status can have up to a 14-character name. A maximum of eight status conditions is possible.
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu
Inactive Exit Tone upon feature exit.
1 Perform one of the following actions:
•
• Press the preprogrammed Status button.
or to Sts and press the Menu Select button directly below Sts.
The display shows the last acknowledged status call, or the first status in the list.
2 Perform one of the following actions:
• Use the keypad to enter a number corresponding to the location in the status list.
3 Press the PTT button to send the status.
When the dispatcher acknowledges, you hear four tones and the display shows Ack received . The radio returns to normal dispatch operation.
If no acknowledgment is received, you hear a lowpitched tone and the display shows No acknowledge
.
4 Press to return to the Home screen.
No traffic is heard on trunked channels while
Status Calls is selected. If the radio detects no
Status Call activity for six seconds, an alert tone sounds until you press or the PTT button.
Responding to the Dynamic Regrouping Feature
(Trunking Only)
This feature allows the dispatcher to temporarily reassign selected radios to a particular channel where they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician.
You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher.
72
English
Note: If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, you hear an invalid tone.
When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. You hear a Gurgle tone and the display shows the dynamically regrouped channel’s name.
Press the PTT button to talk. Release PTT button to listen.
When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped.
Requesting a Reprogram (Trunking Only)
This feature allows you to notify the dispatcher when you want a new dynamic regrouping assignment.
Perform one of the following actions:
• Press the preprogrammed Reprogram
Request button to send reprogram request to the dispatcher.
•
or to Rpgm then press the Menu Select button directly below Rpgm to send reprogram request to the dispatcher.
The display shows Reprgrm rqst and Please wait
.
If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows Ack received and the radio returns to the
Home screen.
If the dispatcher does not acknowledge the reprogram request within six seconds, you hear a low-pitched alert tone and the display shows No acknowledge
. Try again or press to cancel and return to the Home screen.
Classification of Regrouped Radios
The dispatcher can classify regrouped radios into either of two categories:
Select
Enabled
Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position.
English
73
Select
Disabled
Select-disabled radios cannot change channels while dynamically regrouped.
The dispatcher has forced the radio to remain on the dynamic-regrouping channel.
The Scan or Private Call feature cannot be selected while your radio is Select Disabled.
Dynamic Zone Programming (DZP)
Note: Your radio must be preprogrammed to allow you to use this feature. This feature works on the condition at least one zone in the radio must be a non-dynamic zone.
This feature provides one or more Dynamic Zones to store the frequent used channels be it conventional or trunking. These dynamic channels are saved from pre-existing (non-dynamic) channels in the radio. This saves the time and effort from the regular navigation around the working zones and channels. User can also delete or update the list in the Dynamic Zone.
Entering the Dynamic Zone to Select a Dynamic
Channel
1
or to Zone then press the Menu Select button directly below Zone.
The display shows the Zone screen.
2
or to <# Dynamic Zone Channels>.
[2]
3 Perform one of the following actions:
• Press the Menu Select button below Sel to select.
• Press the Menu Select button below Exit to exit.
If you have selected one of the Dynamic Zone
Channels list, the display returns to Home screen with the selected <# Dynamic Zone Channels> shown on the screen.
[2]
If you have selected Exit without selecting any
Dynamic Zone Channels list, the display returns to
Home screen without any changes.
74
2
# indicates number of the channel on the 16-Position Switch which are numbered from 1 to 16.
English
Saving a Channel in the Dynamic Zone from List
Selection
The radio must be in Dynamic Zone in order to perform this operation.
1
or to ZnPr. Press the Menu Select button directly below ZnPr to enter Program Zone screen.
2 Press the Menu Select button directly below
Edit
.
The display shows Search Options screen.
3
or to List Selection. Press the Menu
Select button directly below Sel.
The display shows Select Zone screen.
4
or to the required zone. Press the Menu
Select button directly below Sel.
The display shows Select Chan screen.
5
or to the required channel. Press the Menu
Select button directly below Sel.
The display shows Channel updated.
6 Press theMenu Select button directly below Exit to return to Home screen.
Saving a Channel in the Dynamic Zone from
Channel Name
The radio must be in Dynamic Zone in order to perform this operation.
1
or to ZnPr then press the Menu Select button directly below ZnPr to enter Program Zone screen.
2 Press the Menu Select button directly below
Edit
.
The display shows Search Options screen.
3
or to Channel Name then press the Menu
Select button directly below Sel.
The display shows a blinking cursor on the
Channel Name screen.
4 Use the keypad to type or edit the channel name.
5 Press the Menu Select button directly below Srch once the entry is done to initiate searching.
English
75
76
English
You can cancel this operation at this step by pressing the Menu Select button directly below
Cncl
to return to Search Options screen.
The display shows Searching.... Once found, the display shows Channel updated.
If the radio is triggered to search for an empty entry, the display shows Invalid entry.
If the entry does not match, the display shows
Channel name not found
. Repeat from step
or
to search again.
6 Press to return to the Home screen.
Deleting a Channel in the Dynamic Zone
The radio must be in Dynamic Zone in order to perform this operation.
1
or to ZnPr then press the Menu Select button directly below ZnPr to enter Program Zone screen.
The display shows the dynamic channels list.
2
or to the saved dynamic channel then press the Menu Select button directly below Del.
The display shows Channel deleted screen.
3 Press the Menu Select button below Exit to return to Home screen.
The Home screen shows <Dynamic Zone
Channels>
.
If the channel deleted is the Home channel, the
Home screen shows <Zone Name>+”Blank”.
Contacts
This feature provides “address-book” capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call.
Contact entries are alphabetically sorted according to entry alias. Each alias can have up to five IDs of different call types associated with it.
Additionally, each entry, depending on context
(conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call,
Selective Call, Private Call, or Call Alert.
Each entry within Contacts contains the following information:
• Call Alias (Name)
• Call ID (Number)
• Call Type (Icon)
• WACN ID (Astro 25 Trunking IDs only)
• System ID
Note: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries.
Your radio also supports a maximum of 50 call lists.
Each list can store up to 100 IDs (numbers).
Note: Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information.
The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You hear the Menu Inactive
Exit Tone upon feature exit.
Making a Private Call from Contacts
Your radio must be preprogrammed to allow you to use this feature.
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the required subscriber alias.
3 Perform one of the following actions:
•
• Press the Menu Select button directly below
Optn
and proceed to the next step.
or to scroll through the available IDs for the selected subscriber alias and proceed to step
.
4
or to Call and press the Menu Select button directly below Sel.
5
or to select the call type.
6 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
7 Press the PTT button to initiate the call.
During the call, the display shows the subscriber alias.
8 Press and hold the PTT button to talk. Release the
PTT button to listen.
The LED lights up solid red when the PTT button is pressed.
If there is no voice activity for a preprogrammed period of time, the call ends.
77
English
78
If the call reaches the maximum ring time, the call ends.
Adding a New Contact Entry
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to [New Contact] and press the Menu
Select button directly below Sel.
3
or to Name and press the Menu Select button directly below Edit.
The display shows Edit name and a blinking cursor appears.
4 Use the keypad to enter the name and press the
Menu Select button directly below Ok once you have entered the name.
To cancel this operation, press the Menu Select button directly below Cncl to return to the previous screen.
5
or to [Add Number] and press the Menu
Select button directly below Sel.
English
6
or to Number 1 and press the Menu Select button directly below Edit.
The display shows Edit Number 1 and a blinking cursor appears.
7 Use the keypad to enter the number and press the Menu Select button directly below Ok once you have entered the number.
To cancel this operation, press the Menu Select button directly below Cncl to return to the previous screen.
8 Perform one of the following actions per the information you need to add to current name:
• or to Type 1 and press the Menu Select button directly below Edit.
or to the required mode and press the
Menu Select button directly below Ok.
through
exisitng system IDs.
through
number.
9 Press the Menu Select button directly below Done once you have finished.
The display shows <Entry> Stored, confirming that the contact entry has been added.
The radio returns to the main Contacts screen.
Deleting a Contact Entry
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to delete and press the
Menu Select button directly below Optn.
3
or to Del and press the Menu Select button directly below Sel.
The display shows Delete <Entry> confirm?.
4 Select the Menu Select below Yes to delete the entry, or No to cancel and return to the main screen of Contacts.
The display shows <Entry> deleted and the radio returns to the main screen of Contacts.
Adding a Contact to a Call List
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to add and press the Menu Select button directly below Optn.
3
or to Add to CallLst and press the Menu
Select button directly below Sel.
4 Perform one of the following actions:
•
• or to the required Call List and press the
Menu Select button directly below Add to add to the Call List.
or to Cncl to cancel and return to the main screen of Contacts.
The display shows momentary Please wait before showing <Entry> added to Call List, confirming the addition of the contact to the list.
The radio returns to the main display of Contacts.
English
79
Removing a Contact from a Call List
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to delete and press the Menu Select button directly below Optn.
3
or to Rm frm CallLst and press the Menu
Select button directly below Sel.
The display shows Remove <Entry> frm Call
List?
.
4 Press the Menu Select button directly below Yes to remove the entry from the Call List, or No to cancel and return to the main display of Contacts.
The display shows momentary Please wait before showing <Entry> removed from Call
List
, confirming the removal of the contact from the list.
The radio returns to the main display of Contacts.
Methods of Contact Editing in a Call List
80
English
Editing an Entry Alias
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to edit and press the Menu Select button directly below Optn.
3
or to Edit and press the Menu Select button directly below Sel.
4
or to the entry alias you wish to change and press the Menu Select button directly below Edit.
A blinking cursor appears.
5 Use the keypad to edit the name and press the
Menu Select button directly below Ok once you have finished.
The display returns to the Edit Contact screen.
6 Press the Menu Select button directly below Done to save your changes and return to the main screen of Contacts.
Editing as Entry ID
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to edit and press the Menu Select button directly below Optn.
3
or to Edit and press the Menu Select button directly below Sel.
4
or to the entry ID you wish to change and press the Menu Select button directly below Edit.
A blinking cursor appears.
5 Use the keypad to edit the number and press the
Menu Select button directly below Ok once you have finished.
The display returns to the Edit Contact screen.
6 Press the Menu Select button directly below Done to save your changes and return to the main screen of Contacts.
Editing a Call Type
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to edit and press the Menu Select button directly below Optn.
3
or to Edit and press the Menu Select button directly below Sel.
4
or to Type and press the Menu Select button directly below Edit.
5
or to choose from the list of call types given and press the Menu Select button directly below
Ok
.
The display returns to the Edit Contact screen.
6 Press the Menu Select button directly below Done to save your changes and return to the main screen of Contacts.
English
81
Viewing Details of a Contact
1
or to Cnts and press the Menu Select button directly below Cnts.
The entries are alphabetically sorted.
2
or to the entry you want to view and press the Menu Select button directly below Optn.
3
or to View and press the Menu Select button directly below Sel.
The display shows all the numbers associated with the entry.
82
Scan Lists
Scan lists are created and assigned to individual channels/ groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/ group.
Your radio supports different types of Scan Lists:
• Trunking Priority Monitor Scan List
• Conventional Scan List
• Talkgroup Scan List
English
Please refer to a qualified radio technician for the maximum number of Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician.
Viewing a Scan List
1
or to ScnL and press the Menu Select button directly below ScnL.
2
or to view the members on the list.
3 Press to exit the current display and return to the Home screen.
Editing the Scan List
This feature lets you change scan list members and priorities.
1 Perform one of the following actions:
•
• Long press the preprogrammed Scan List
Programming button (side button).
• Move the preprogrammed Scan List
Programming switch to programming position.
or to ScnL then press the Menu Select button directly below ScnL.
The display shows the lists that can be changed.
2
or to the entry you want to edit.
3 Perform one of the following actions:
• Press the Menu Select button directly below
Sel
to add and/or change the priority of the currently displayed channel in the scan list.
• Press the Menu Select button directly below
Del
to delete the currently displayed channel from the scan list.
• Press the Menu Select button directly below
Rcl
to view the next member of the scan list.
4 Perform one of the following actions to select another channel that needs to be added or deleted
. Otherwise, proceed to the next
step.
• or to the desired channel.
• Use the keypad to enter the desired channel name.
• Use the 16-Position Select knob to select the channel.
5 Perform one of the following actions:
• Move the Scan List Programming switch out of programming position.
• Press to exit scan list programming and return to the Home screen.
Viewing and Changing the Priority Status
on page 84 for more information on how to add and/or change the priority of the currently displayed channel in the scan list.
Changing the Scan List Status
1 Perform one of the following actions:
• Long press the preprogrammed Scan List
Programming button (side button).
• Move the preprogrammed Scan List
Programming switch to programming position.
The display shows the programming mode icon and the first list member.
2
or to the member you want to edit.
3 Perform one of the following actions:
• Press the Select button once to add the currently displayed channel to the scan list.
83
English
• Press the Select button one or more times to change the scan list status icon of the currently displayed channel.
4 Perform one of the following actions:
• or to select more list members whose scan status you want to change.
• Use the keypad to go directly to that scan list member.
• Use the 16-Position Select knob to select another scan list member.
5 Move the Scan List Programming switch out of programming position.
Viewing and Changing the Priority Status
Perform one of the following actions:
• Press the Menu Select button directly below
Sel
one or more times to change the priority status of the current displayed channel.
• Press the Select button one or more times to toggle different status of the Scan List status icon of the current displayed channel.
The radio shows one of following priority status icons and scenarios:
• A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The
LED lights up solid green.
• A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green.
• A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-
One channel, regardless of traffic on nonpriority channels.
• No icon indicates that the current channel is deleted from the scan list.
Scan
This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels.
84
English
Turning Scan On or Off
Perform one of the following actions:
• Press the preprogrammed Scan button to toggle Scan On or Scan Off to initiate or stop scan.
•
• Turn the preprogrammed Scan switch to the
Scan on or Scan off position to initiate or stop scan.
or to Scan and press the Menu Select button directly below Scan.
If the scan is enabled, the display shows Scan on and the scan status icon.
If the scan is disabled, the display shows Scan
Off
.
The radio returns to the Home screen.
Making a Dynamic Priority Change (Conventional Scan
Only)
While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel.
This change remains in effect until scan is turned off.
Scan then reverts to the preprogrammed (original) setting.
Making a Dynamic Priority Change via the preprogrammed Dynamic Priority button: a) When the radio locks onto the channel designated as the new Priority-Two channel, press the preprogrammed Dynamic Priority button.
The radio continues scanning the remaining channels in the list.
Deleting a Nuisance Channel
If a channel continually generates unwanted calls or noise (termed a “nuisance” channel), you can temporarily remove the unwanted channel from the scan list.
This capability does not apply to priority channels or the designated transmit channel.
When the radio is locked onto the channel to be deleted, perform one of the following actions:
• Press the preprogrammed Nuisance Delete button.
85
English
86
•
or to Nuis and press the Menu Select button directly below Nuis.
The radio continues scanning the remaining channels in the list.
Restoring a Nuisance Channel
To restore the deleted nuisance channel, perform one of the following actions:
• Turn scan off, and then on.
• Change channels.
• Turn off the radio, and then turn it back on.
Nuisance mode delete can be disabled by the system administrator.
Call Alert Paging
This feature allows your radio to work like a pager.
Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system.
Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a call alert page if there is no answer after the maximum ring time, or when you press the PTT button.
Note: This feature must be preprogrammed by a qualified radio technician.
Receiving a Call Alert Page
When you receive a Call Alert page, you hear four repeating alert tones and the LED blinks green. The call received icons blinks and the display shows Page received
.
Press any button to clear the Call Alert page.
information on returning the call.
Sending a Call Alert Page
The following methods are options on how to send a call alert page. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
Note: If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio
English
is left idle long enough for the time to expire. You hear the Menu Inactive Exit Tone upon feature exit.
• Sending a call alert page via the preprogrammed
Quick Access (One-Touch) Call Alert Paging
button: a) Press the preprogrammed Quick Access
(One-Touch) Call Alert Paging button to send a page to the preprogrammed ID.
The display shows Paging...<Number>.
If the call alert page is sent successfully, you hear a tone and the display shows Ack received
. The radio returns to the Home screen.
If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge
. Press the Menu Select button directly below Ok to return to the main screen for Contacts.
• Sending a call alert page via the radio menu Page: a) or to Page.
b) Press the Menu Select button directly below
Page
.
c) Press the Menu Select button directly below
Cnts
to view the required ID, or to the required ID, or use the keypad to enter the required ID.
d) Press the PTT button to send the page.
The display shows Paging...<Number>.
If the call alert page is sent successfully, you hear a tone and the display shows Ack received
. The radio returns to the Home screen.
If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge
. Press the Menu Select button directly below Ok to return to the main screen of
Contacts.
• Sending a call alert page via the radio menu Call: a) or to Call.
b) Press the Menu Select button directly below
Call
.
c) or to select the alias or ID, and press the
PTT button to initiate the call.
English
87
If the target radio does not respond after a preprogrammed period of time, the display shows Send page?.
d) To send the call alert page, press the Menu
Select button directly below Yes. To exit the screen without sending the call alert page, press the Menu Select button directly below
No
.
The display shows Paging...<Alias>.
If the call alert page is sent successfully, you hear a tone and the display shows Ack received
. The radio returns to the Home screen.
If the call alert page is not acknowledged, you hear a low tone and the display shows No acknowledge
. Press the Menu Select button directly below Ok to return to the main screen of
Contacts.
Emergency Operation
The Emergency feature is used to indicate a critical situation.
88
English
If the Top (Orange) button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel.
Your radio supports the following Emergency modes:
• Emergency Alarm
• Emergency Call (Trunking Only)
• Emergency Alarm with Emergency Call
• Silent Emergency Alarm
Check with your dealer or system administrator for more information on the programming of this feature.
Each channel can only assigned one of the
Emergency modes above. The radio responds differently when pressing the preprogrammed
Emergency button in each channel.
Note: To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second.
The radio operates in the normal dispatch manner while in Emergency Call, except if enabled, it returns to one of the following:
Tactical/Non-
Revert
Non-Tactical/
Revert for
Conventional system
Non-Tactical/
Revert for
Trunking system
The radio sends emergency alarm and/or make emergency call on the current selected channel.
The radio reverts to the preprogrammed emergency channel to send alarm and/or make emergency call.
The radio reverts to the preprogrammed emergency talkgroup to send alarm and/or make emergency call.
Man Down is an alternate way to activate the
Emergency feature on the condition the Emergency must be set up for this feature to operate.
on page 95 for details.
Sending an Emergency Alarm
This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher.
Note: Emergency button press timer by default is set to 1 second. This timer is programmable from 0 – 6 seconds by a qualified technician.
Press the preprogrammed Emergency button.
One of the following scenarios occurs:
• The display shows Emergency on the current zone and channel. You hear a short mediumpitched tone and the LED blinks red momentarily.
• You hear the radio sounds a short low-pitched tone to indicate that the selected channel does not support emergency and rejects to launch emergency mode.
When you receive the dispatcher’s acknowledgment, the display shows Ack received. You hear four tones, the alarm ends, and the radio exits the
Emergency Alarm mode.
If no acknowledgement is received, the display shows
No acknowledge
. The alarm ends when the timer expires and the radio exits the Emergency Alarm mode.
Sending an Emergency Call (Trunking Only)
This feature gives your radio priority access to a talkgroup.
1 Press the preprogrammed Emergency button.
89
English
90
English
One of the following scenarios will occur:
• The display shows Emergency on the current zone and channel. You hear a short mediumpitched tone and the LED blinks red momentarily.
• You hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
3 Press and hold the PTT button. Speak clearly into the microphone.
4 Release the PTT button to end the transmission and wait for a response from the dispatcher.
5 To exit Emergency Call, press and hold the preprogrammed Emergency button for about a second.
Sending an Emergency Alarm with Emergency Call
This feature gives your radio priority access on a channel for conventional system, and to a talkgroup for trunking system.
1 Press the preprogrammed Emergency button.
If successful, the display shows Emergency on the current zone and channel. You hear a short, medium-pitched tone and the LED blinks red momentarily.
The radio exits Emergency Alarm and enters the
Emergency Call state when one of the following scenarios occur:
• You receive the dispatcher’s acknowledgment.
The display shows Ack received.
• You receive no acknowledgement. The display shows No acknowledge.
• You press the PTT button while in the
Emergency Alarm mode.
If unsuccessful, you hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0
cm) from your mouth.
3 Press and hold the PTT button. Speak clearly into the microphone.
4 Release the PTT button to end the transmission and wait for a response from the dispatcher.
5 To exit Emergency Call, press and hold the preprogrammed Emergency button for about a second.
Turning the radio off also cancels the emergency state.
Sending a Silent Emergency Alarm
This feature allows you to send an Emergency Alarm to the system without triggering any audio or visual indicators.
1 Press the preprogrammed Emergency button.
The display shows no changes, the LED does not light up, and you hear no tones. The silent emergency state continues until you perform the next step.
2 Perform one of the following actions:
• You press and hold the preprogrammed
Emergency button for about a second to exit the Silent Emergency Alarm mode.
• Press and release the PTT button to exit the
Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode.
Change of Channels during Emergency
For ALL Emergency transmissions, when changing channels:
• If the new channel is also preprogrammed for
Emergency, you can change channels while in
Emergency operation. The emergency alarm or call continues on the new channel.
• If the new channel is not preprogrammed for
Emergency, the display shows No emergency, and you hear an invalid tone until you exit the
Emergency state or change to a channel preprogrammed for Emergency.
Emergency Keep-Alive Feature
This feature, when enabled, prevents the radio from being turned off via the On/Off Control Knob when the radio is in the Emergency state.
English
91
Note: The radio only exits the Emergency state using one of the ways mentioned in the previous sections.
Sending an Emergency Call (Trunking Only)
89,
Sending an Emergency Alarm with Emergency
92
Fireground (Conventional Only)
The portable Fireground Communications System is designed for deployment at an incident scene. It consists of five central components:
• Your APX portable radios
• Incident Management Software
• Command Terminal
• Radio Frequency (RF) Modem
• DVRS (Optional)
These components provide on-scene and inbuilding radio coverage, and enhanced personnel accountability and monitoring.
The radio helps to indicate your presence on the scene if it is in the range of the Incident Commander command terminal.
Each Fireground Communication System radio automatically reports your radio ID on the commander mobile command terminal. Your name, riding position and sector are all can be configured to be seen at the
Commander’s command terminal.
If you have a critical situation, you can press the
Emergency button which activates an alarm on the
Incident Management Software at the command terminal.
The Fireground signals transmission is always exchanging data between your radio and the RF
Modem and command terminal. The status of your radio includes:
• Powering up or down the radio
• Automatic response to Polling
• Response to Evacuation commands
• Pressing the PTT button to make voice transmission
• Sending an Emergency Alarm and Call
Entering Fireground Zone Channel
1 Upon powering up, perform one of the following actions:
English
• If the Fireground Zone Channel is set as default, you hear gurgle tone and the home screen. You are in Fireground zone channel.
• If the Fireground Zone Channel is set as default, but you hear a short, low-pitched tone, the display shows Reg failed to indicate that the command terminal does not respond to
Fireground Zone Channel. Get a qualified technician for assistance.
• If your home channel is not Fireground Zone
Channel, toggle or change the radio zone channel to Fireground Zone Channel.
2 Listen for a transmission. Adjust the Volume
Control Knob if necessary.
3 Perform one of the following actions:
• Press and hold the preprogrammed Volume
Set button to hear the volume set tone. Adjust the Volume Control Knob if necessary.
Release the Volume Set button.
• At the desired Fireground zone and channel, press the preprogrammed Monitor button and listen for activity. Adjust the Volume Control
Knob if necessary.
• If your radio is working in Fireground Zone
Channel, proceed to next step.
4 Press and hold the PTT button to transmit. The
LED lights up solid red while transmitting. Talk into the microphone clearly if needed.
5 Release the PTT button to receive.
You hear a Transmit End Tone.
Responding to Evacuation Indicator
When Incident Commander triggers Evacuation signal from his command terminal, the RF Modem updates everyone in the Fireground Communication
System with the order to evacuate the incident site.
Your radio sounds the Evacuation Tone at the profile maximum alert tone volume level. The display shows
EVACUATE
.
Perform one of the following actions:
• Move the Volume Control Knob to adjust the volume of the Evacuation Tone from full volume.
• Perform any action on the radio other than volume adjustments to cancel the evacuation indications and update the command terminal.
93
English
• If preprogrammed with Manual
Acknowledgement of Evacuation Command, pressing the PTT button shall cancel the indications and acknowledge the command terminal.
94
Tactical Public Safety(TPS) (Conventional
Only)
TPS enabled the user of a group to identify a transmission starts and ends clearly by displaying the caller name or ID on the radio display.
Using TPS Normal Transmission
At TPS Zone Channel, perform one of the following actions:
• Press PTT button to transmit. Talk clearly into the microphone. Release PTT button to listen.
• Receive and listen to call, the radio displays the caller’s name or ID.
Using TPS Emergency Transmission
The following are two important alert tones designed for this feature.
English
Emergency
Beacon
Emergency
Call De-Key
Sidetone
During Emergency if the TPS radio user pushes the Emergency button, the radio sounds a Beacon at the maximum volume of the radio at radio’s internal speaker and it is not adjustable. This beacon goes to silent when user presses the PTT button for voice transmission.
The radio sounds an alert tone to remind radio user that the
Emergency Mode is still active after user releases the PTT button for an
Emergency call transmission. The volume of loudness depends on the maximum tone at your radio profile.
1 Press the Emergency button to enter Emergency
Mode.
You hear Emergency Beacon.
2 Press PTT button to make Emergency Call.
3 Release to listen.
You hear Emergency Call De-Key Sidetone. After a short pause, you hear Emergency Beacon.
4 Long press Emergency button to exit Emergency mode and cancel Emergency Beacon.
Man Down
Man Down condition is determined based upon the radio tilt angle or a combination of radio tilt angle and the lack of radio motion.
Man Down feature is an alternate way to activate the
Emergency feature if Emergency has been programmed in your radio.
Note: This feature could be preprogrammed for all channels that support Emergency feature or could be preprogrammed specifically to a zone and channel which has Emergency feature. Consult your agent or qualified technician for more details.
Your radio automatically activates Emergency Alarm or Call when the radio achieves or passes a tilt angle threshold or a combination of the angle threshold and radio motion below the motion sensitivity level, depending upon how the radio is programmed. The radio must stay in this condition for a preprogrammed amount of time before the Emergency Alarm or Call is activated.
Note: It is recommended that an Emergency button is preprogrammed in order to allow the user to exit the emergency condition.
The Man Down feature provides a Clear function to the user. After a Man Down condition has been detected, the user can press a preprogrammed Clear button or preprogrammed Menu Select button to cancel the Man Down condition. The radio remains in the Man Down state without triggering an emergency condition until the radio is moved out of the Man
Down state, at which point Man Down functionality resumes.
The Man Down feature has three phases:
1 The radio senses the Man Down condition and
Pre-Alert Timer is initiated.
2 Man Down condition continues for the time duration defined in the Pre-Alert Timer field. At the end of this time, the radio alerts the user on the
Man Down status with an audible alert tone and
Man-Down
text on the screen.Man Down condition continues for the time duration defined in the Pre-
Alert Timer field. At the end of this time, the radio alerts the user on the Man Down status with an audible alert tone and text on the screen. The
Post-Alert Timer also initiates at this point.
95
English
96
English
3 Man Down condition continues for the time duration defined in the Post-Alert Timer field. Once the timer expires, the Emergency alarm is transmitted. The Man Down Clear function is used in this phase to cancel the Man Down condition.
The following scenarios affect the timers:
• Pressing the PTT button suspends the Man Down timers; releasing the PTT button re-initiates the
Pre-Alert Timer.
• Pressing other buttons on the radio does not impact these timers.
• Repositioning the radio exits the Man Down feature, which stops and resets the timers.
• Pressing a preprogrammed Clear button or pressing a Menu Select button preprogrammed for Clear stops and resets the timers. The timers do not restart until the radio is repositioned.
Note: Emergency must be set up for this feature to operate. For details on operating the Emergency
on page 88.
If the radio is preprogrammed to horizontal only, it must be worn in a vertical position otherwise the Man
Down alert may be inadvertently triggered.
When the radio is programmed with Man Down feature, special care is required when charging the radio with a wall mounted charger. See
Proper Ways to Handle the Radio
on page 187 for details.
Pre-Alert Timer
This timer sets the amount of time that a Man Down condition must be present before the radio-user is warned of the Man Down condition.
When the radio detects that it has returned to the vertical position or when the radio detects motion, the
Pre-Alert timer stops and is reset.
The Pre-Alert timer reinitiates when the radio detects it is in the horizontal position or motionless again.
Post-Alert Timer
This timer sets the amount of time the radio needs to remain in the Man Down condition before the
Emergency alarm is transmitted. When the Post-Alert
Timer is initiated, the radio alerts the user with an audible tone and displays the “Man-Down” text.
on page 98 to exit
Man Down feature.
Radio Alerts When Man Down Feature is Triggered
The Man Down alert tone volume is directly related to the radio’s volume. Ensure that the radio’s volume is loud enough so that the user does not miss the Post-
Alert tone.
Note: If the radio is programmed with Silent
Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature.
If the radio is programmed in Surveillance Mode, the radio inhibits all tones and lights on the radio including the Man Down tones.
Triggering Emergency
When the user does not clear the Man Down condition and the Post-Alert Timer comes to an end,
Emergency Alarm or call is triggered. The radio sends emergency message to units within the same
Talkgroup. The radio also sends ID number and GPS coordinates to dispatcher if these features are enabled. User can exit Emergency following the
on page 88 for details.
Note: At this point the Man Down features is complete. Use normal Emergency procedures to cancel Emergency transmissions.
Radio Alerts When Man Down Enhanced is Triggered
Note: This feature is to be preprogrammed specifically to a zone and channel which supports
Emergency feature.
The volume and repetition duration of Man Down
Enhanced alert tone could be customized and preprogrammed to suite the required situation.
Consult your agent or qualified technician for more details.
When the radio initiates Man Down Enhanced, you hear the Critical Man Down Continuous alert tone from the radio speaker. The volume of this tone is set to the louder of the preprogrammed minimum level or the current radio speaker level. This acts as a beacon to find the radio.
Note: If the radio is programmed with Silent
Emergency, the radio inhibits the alert tone and visual alert associated with the emergency feature.
If the radio is programmed in Surveillance Mode, the alert tone can be heard from the radio speaker.
Once the alert tone is active, changing to another channel with different setup triggers a different response from the radio as described next.
97
English
• The alert tone is inhibited when you change to a channel without Emergency feature.
• The alert tone is inhibited when you change to a channel with Emergency but no Man Down feature.
• The current alert tone is inhibited and is replaced with a different alert tone when you change to a channel with Emergency and different Man Down configuration.
• The alert tone continues when you change to a channel with Emergency and similar Man Down configuration.
Exiting Man Down Feature
If you are not in a real Man Down situation, you should exit the Man Down feature and prevent emergency from going off with the following operation.
Perform one of the following actions:
• Repositioning the radio or shaking the radio
(when motion sensitivity is enabled).
• Press the preprogrammed Man Down Clear button to exit.
98
English
• Press the Menu Select button below Clr to exit.
Re-Initiating Man Down
After exiting the Emergency Operation when the radio is still in Man Down condition (tilted achieving threshold angle or motionless), user must first exit
Man Down condition to then reinitiate the Man Down feature.
Return the radio to the vertical position or shake the radio (when motion sensitivity is enabled).
Testing the Man Down Feature
Enable the Emergency feature with Silent Alarm disabled, but not in Surveillance Mode before running this test on the radio.
1 Turn the radio on and place in the vertical position, for at least 5 seconds.
2 Lay the radio down in the horizontal position.
3 Wait for alert tone.
One of the following scenarios will occur:
• The radio alerts with audible tone and displays
Man-Down
.
• If no tone is heard, make sure that the Man Down feature is enabled on your radio. If Man Down feature was not enabled, please enable it and
• If the Man Down feature is enabled and no tone is heard, send the radio to a qualified technician.
Automatic Registration Service (ARS)
This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server.
Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text
Messaging Service (TMS).
The Automatic Registration Service for the radio consists of two (2) modes:
• ARS Server Mode (default mode)
• ARS Non-Server Mode
Note: The default ARS mode can be changed by a qualified radio technician using the radio’s programming software.
Selecting or Changing the ARS Mode
The following methods are options on how to select or change the ARS Mode. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Selecting or Changing the ARS mode via 16-
Position Select knob: a) Once the zone you want is displayed, turn the preprogrammed 16-Position Select knob to the desired mode.
• Selecting or Changing the ARS mode via the radio menu: a) or to Chan.
b) Press the Menu Select button directly below
Chan
.
The display shows the current channel name.
c) or to the required channel or mode.
One of the following scenarios occur:
99
English
• In ARS Server Mode, the display shows the zone and ARS server channel.
• In ARS Non-Server Mode, the display shows the zone and ARS non-server channel.
• If the channel or mode selected is unprogrammed, the display shows
Unprogrammed
. Repeat this step.
d) Press Sel to confirm the displayed channel.
100
User Login Feature
This feature allows you as the user to be associated with the radio. With this association, every data application (Example: Text Messaging Service) takes on a friendly username.
You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.
Note: A predefined username that is set more than the maximum allowed characters is an invalid name.
Logging In as a User
1 Perform one of the following actions:
English
•
• Press the preprogrammed User Login button.
or to User and press the Menu Select button directly below User.
The display shows the User Login screen.
2 Perform one of the following actions:
•
or to [ID Entry] and press the Menu
Select button directly below Edit to enter ID. A blinking cursor appears on the screen. Use the
keypad to type or edit a user name. Press the
Menu Select button directly below Ok to submit.
• or to scroll through the list of predefined user names. Press the Menu Select button directly below Sel to select the predefined user name.
• Press and hold or to scroll through the list of predefined user names at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined user name.
If the ID is invalid, the display shows momentary
Invalid ID
.
3 Enter your Personal Identification Number (PIN) number.
4 Press the Menu Select button directly below
Logn
.
One of the following scenarios occurs:
• In ARS Server Mode, the display shows the
User Login Indicator icon, the ID, and In progress
, with Cncl.
• In ARS Non-Server Mode, the display shows the User Login Indicator icon, the ID, and
Logged in
, with Logt and Exit.
• In non-ARS enabled mode, the display shows
Offline
, with Logt and Exit.
One of the following scenarios occurs:
• If the user name is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed.
• If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also shows momentary Login failed.
• Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and Logged in, with Logt and Exit.
Note: To cancel the login process and return to the initial user login screen, press the Menu Select button directly below Cncl.
Logging Out
When you have logged in or you are using Offline mode, you can log out.
Note: Private data refers to all messages in the text messaging Inbox, Draft, and Sent folder. The next user is able to access the Inbox, Draft and Sent messages if private data is not deleted.
1 Press the Menu Select button directly below
Logt
.
One of the following scenarios will occur:
• The display shows Clear private data?.
Proceed to the next step.
• If the Delete Messages On Session End feature is enabled, the radio clears the private data and returns to User Login screen.
2 Perform one of the following actions:
101
English
• Select Yes to clear all your private data. The display shows momentary Private data cleared
.
• Select No to keep your private data.
102
Text Messaging Service (TMS)
This features allows you to quickly send and receive messages and run database queries directly from your radios. The maximum length of characters for a text message is 200.
The types of text messages available:
• A new text message (free form message).
• A predefined message (quick text message).
• An edited quick text message.
• A query (ASTRO 25 Advanced Messaging
Solution).
Note: Query is only supported within ASTRO 25
Advanced Messaging Solution. See
on page 112 for details.
The main menu consists of the following options:
English
• Inbox
• Compose
• Drafts
• Sent
Note: See
on page 43 for more information on the TMS icons and
on page 50 for more information on each menu option.
Accessing the Messaging Features
1 Perform one of the following actions:
• Press the Data Feature button or the preprogrammed TMS Feature button to access the TMS feature screen.
• Press and hold the Data Feature button or the preprogrammed TMS Feature button to access the Inbox.
• Follow the procedure described next to access this feature via the radio menu.
2
or to TMS.
3 Press the Menu Select button directly below TMS to access the TMS feature screen.
4
or to scroll through the main menu options.
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive Exit Tone upon feature exit.
Press the Menu Select button directly below Back at any time to return to the previous screen.
Composing and Sending a New Text Message
During the uppercase and lowercase mode, multitapping the keys only scrolls through the letters. For example, A->B->C, a->b->c.
During the numeric mode, except for the keypad only enters the numeric digits.
, pressing
Subsequent presses of the same key inserts the same digit to the text message (no multi-tap).
1
or to TMS.
2 Press the Menu Select button directly below TMS to access the TMS feature screen.
3 Perform one of the following actions:
• or to Compose and press the Menu
Select button directly below Sel.
• Press the Menu Select button directly below
Exit
to return to the Home screen.
4
or to Text Message and press the Menu
Select button directly below Sel to compose a new message.
A blinking cursor appears on the Compose screen.
5 Use the keypad to type or edit your message.
6 Press the Menu Select button directly below Optn once the message is composed.
7
or to Send Message and press the Menu
Select button directly below Sel.
8 Perform one of the following actions:
•
• or to scroll through the address list and highlight the required address.
or to [Other Recpnt] and press the
Menu Select button below Edit. When a blinking cursor appears in the Enter Address screen, use the keypad to type the address entry.
103
English
9 Press the Menu Select button directly below Send or press the PTT button to send the message.
The display shows the Send Message screen and
Sending msg
.
If the message is sent, you hear a tone and the display shows Msg sent.
If the message is not sent, you hear a low tone, the display shows Send failed and returns to the main TMS screen.
Note: You can append a priority status and/or a request reply to your message. See
Priority Status and Request Reply of a New Text Message
on page 105 for more information.
You can also select the Save to Drafts option to save your message in the Drafts folder to send it at a later time. See
on page 110 for more information.
104
Sending a Quick Text Message
Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently.
English
Each Quick Text message or Query has a maximum length of 50 characters. You can select the required text from the Quick Text or Query.
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed Quick Text button and proceed to Step 4.
• To access this feature via the menu, proceed to the next step.
2
or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen.
3 Perform one of the following actions:
• or to Compose and press the Menu
Select button directly below Sel.
• Press the Menu Select button directly below
Exit
to return to the Home screen.
4
or to Quick Text and press the Menu
Select button directly below Sel for a predefined message.
5
or to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message.
The message appears on the Compose screen, with a blinking cursor at the end of it. Use the keypad to edit the message, if required.
6 Press the Menu Select button directly below
Optn
.
7
or to Send Message and press the Menu
Select button directly below Sel.
8 Perform one of the following actions:
•
• or to scroll through the address list and highlight the required address.
or to [Other Recpnt] and press the
Menu Select button below Edit. When a blinking cursor appears on the Enter Address screen, use the keypad to type the address entry.
9 Press the Menu Select button directly below Send or press the PTT button to send the message.
The display shows the Send Message screen and
Sending msg
.
If the message is sent, you hear a tone and the display shows Msg sent.
If the message is not sent, you hear a low tone, the display shows Send failed and returns to the main TMS screen.
Note: You can append a priority status and/or a request reply to your message. See
Priority Status and Request Reply of a New Text Message
on page 105 for more information.
Priority Status and Request Reply of a New Text
Message
Before sending your message, you can append a priority status and/or a request reply to your message.
Appending a Priority Status to a Text Message
Ensure that an outgoing message is composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information.
Note: The Priority Status icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message
105
English
106
English to let the receiver know that the message is important.
1 Press the Menu Select button directly below
Optn
.
2
or to Mark Important and press the Menu
Select button directly below Sel to indicate the message is important.
The priority status icon appears beside the normal message icon on the label bar.
Removing a Priority Status from a Text Message
Ensure there is an outgoing message composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information.
1 Press the Menu Select button directly below
Optn
.
2
or to Mark as Normal and press the Menu
Select button directly below Sel to remove the priority status from the message.
The display shows the normal message icon on the label bar.
Appending a Request Reply to a Text Message
Ensure that an outgoing message is composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information
1 Press the Menu Select button directly below
Optn
.
2
or to Req Reply and press the Menu Select button directly below Sel to request for a reply.
The request reply icon appears beside the normal message icon on the label bar.
Removing a Request Reply from a Text Message
Ensure that an outgoing message is composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information.
1 Press the Menu Select button directly below
Optn
.
2
or to No Req Reply and press the Menu
Select button directly below Sel to remove the priority status from the message.
The display shows the normal message icon on the label bar.
Appending a Priority Status and a Reply Request to a Text Message
Ensure that an outgoing message is composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information.
1 Press the Menu Select button directly below
Optn
.
2
or to Mark Important and press the Menu
Select button directly below Sel to indicate the message is important.
3
or to Req Reply and press the Menu Select button directly below Sel to request for a reply.
The priority status and request reply icons appear beside the normal message icon on the label bar.
Removing a Priority Status and a Reply Request from a Text Message
Ensure that a outgoing message is composed to allow you to perform this procedure. See
Composing and Sending a New Text Message
more information.
1 Press the Menu Select button directly below
Optn
.
2
or to Mark Important and press the Menu
Select button directly below Sel to remove the priority status icon.
3
or to No Req Reply and press the Menu
Select button directly below Sel to remove the reply status icon.
The display shows the normal message icon on the label bar.
Managing Text Messages
Receiving a Text Message
Note: When you receive a message that is flagged with the “Request Reply” icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message.
The following methods are options on how to receive a text message. The result of all the methods is the
107
English
108
English same. You can use the options interchangeably depending on your preference and the programmed functions.
• Receiving a text message via the Data Feature button or the TMS Feature button: a) When you receive a message, press and hold the preprogrammed Data Feature button or the
TMS Feature button to access the Inbox.
The display shows a list of aliases or IDs, with the sender of the latest received message on top.
• Receiving a text message via the radio menu: a) When the new message icon appears and the display shows momentary New msg, press the
Menu Select button directly below TMS to access the Inbox.
The display shows a list of aliases or IDs, with the sender of the latest received message on top.
Viewing a Text Message from the Inbox
The Inbox can hold up to thirty (30) messages.
Note: or to read the message if the content fills more than one screen.
1 Perform one of the following actions:
•
• Press the Data Feature button or the preprogrammed TMS Feature button to access the TMS feature screen. or to Inbox and press the Menu Select button below Sel.
• Press and hold the Data Feature button or the preprogrammed TMS Feature button to access the Inbox.
or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen. or to Inbox and press the Menu
Select button below Sel.
The display shows a list of aliases or IDs, with the sender of the latest received message on top.
2
or to the required aliases or ID and press the Menu Select button below Sel to view the message.
While on the view message screen, press the
Menu Select button directly below Optn, Del, or
Back
to access the option.
• Select Optn to configure the message settings.
• Select Del to delete the message.
• Select Back to return to the previous screen.
Note: The icon at the top right corner of the screen indicates the status of the message. See
Text Messaging Service (TMS) Indicators
48 for more information.
Replying to a Received Text Message
Note: The original date and time stamp, address and message content is automatically appended to the reply message.
1
or to the required aliases or ID and press the Menu Select button below Sel to view the message.
2 Press the Menu Select button directly below Rply to reply to a message.
3 Perform one of the following actions:
•
•
• or to Text Message and press the Menu
Select button directly below Sel.
or to Quick Text and press the Menu
Select button directly below Sel for a predefined message.
or to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message.
One of the following scenarios occurs:
• A blinking cursor appears on the Compose screen.
• The predefined message appears on the
Compose
screen, with a blinking cursor at the end of it.
4 Use the keypad to type or edit your message.
5 Press the Menu Select button directly below Optn once you have completed the message.
6
or to Send Message and press the Menu
Select button directly below Sel to send the message.
The display shows the Send Message screen and
Sending msg
.
Note: Press the Menu Select button directly below
Back
at any time to return to the previous screen.
You can append a priority status and/or a request
Request Reply of a New Text Message
for more information.
109
English
110
English
Accessing the Drafts Folder
This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in.
1
or to TMS.
2 Press the Menu Select button directly below TMS to access the TMS feature screen.
3
or to Drafts and press the Menu Select button below Sel.
The display shows a list of drafts, with the latest text message drafted on top.
4
or to the required text message press the
Menu Select button below Sel to view the message.
Press the Menu Select button directly below
Edit
, Del, or Back to access the option.
• Select Edit to edit the message before sending it.
• Select Del to delete the message.
• Select Back to return to the previous screen.
Sent Text Messages
Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list.
The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest message in the folder is deleted when the
11th message comes in.
Viewing a Sent Text Message
1 Perform one of the following actions:
•
• Press the Data Feature button or the preprogrammed TMS Feature button to access the TMS feature screen.
or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen.
2
or to Sent and press the Menu Select button below Sel.
The display shows a list of aliases or IDs, with the recipient of latest sent message on top.
3
or to the required aliases or ID and press the Menu Select button below Sel to view the message.
While on the view message screen, press the
Menu Select button directly below Optn, Del or
Back
to access the option.
• Select Optn to configure the message settings.
• Select Del to delete the message.
• Select Back to return to the previous screen.
Note: The icon at the top right corner of the screen indicates the status of the message. See
Text Messaging Service (TMS) Indicators
48 for more information.
Sending a Sent Text Message
1 Press the Menu Select button directly below Optn while viewing the message.
2
or to Send Message and press the Menu
Select button directly below Sel.
3 Perform one of the following actions:
• or to scroll through the address list and highlight the required address.
• or to [Other Recpnt] and press the
Menu Select button below Edit. When a blinking cursor appears in the Enter Address screen, use the keypad to type the address entry.
4 Press the Menu Select button below Send or the
PTT button to send the message.
The display shows the Send Message screen and
Sending msg
.
Note: Press the Menu Select button directly below Back at any time to return to the previous screen.
You can append a priority status and/or a request reply to your message. See
Request Reply of a New Text Message
105 for more information.
Deleting a Text Message
1 From the Inbox, Draft, or Sent screen, or to scroll through the messages.
2 Press the Menu Select button directly below Del to delete the current message.
111
English
112
English
Deleting All Text Messages
1 Perform one of the following actions:
•
• Press the Data Feature button or the preprogrammed TMS Feature button to access the Messaging feature screen.
or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen.
2
or to Inbox or Sent then press the Menu
Select button below Clr to select all messages in the selected folder.
The display shows Del All?.
3 Perform one of the following actions:
• Press the Menu Select button directly below
Yes
to delete all the messages in the selected folder.
• Press the Menu Select button directly below
No
to return to the main TMS feature screen.
ASTRO 25 Advanced Messaging Solution
The ASTRO 25 Advanced Messaging Solution allows you to quickly send and receive messages and run database queries directly from your data-enabled
Motorola two-way radios. Federal mandate requires
Two-Factor Authentication when querying Federal and State databases. With this advance messaging solution you have the ability enable Two-Factor
Authentication.
With Query and Two-Factor Authentication, you can use a secure system logon to initiate and receive key information on people, vehicles and properties when doing the regular security patrol. You can access to local or external databases such as the National
Crime Information Center (NCIC), for "Hot Hits" on priors and warrants. Query and Two-Factor
Authentication has Criminal Justice Information
Services (CJIS) security compliance for queries.
With this Advanced Messaging Solution, ARS functionality splits between two protocols:
• ARS for Device Registration
• New User Authentication for User Login
TMS functionality splits between two protocols:
• TMS for messaging
• New Service Advertisement for service availabilities
The radio with Two-Factor capabilities are backward compatible with the existing device registration system and TMS servers.
System Setup for ASTRO Advanced Messaging
Solution
Your user name, unit ID and password all need to be provisioned in PremierOne
™
. Your user account in
PremierOne needs to be linked to an RSA account specifying a token to be used with the Two-Factor passcode.
The radios caches the user name, unit ID and or
Single Factor password in the codeplug, this allows the radio to automatically log in to use Single Factor authentication upon power up or mode change. The
Two-Factor passcode is not stored in the codeplug.
You can upgrade the Single Factor session to a Two-
Factor session by entering the Two-Factor passcode only. After an interruption (for example mode change,
DSR switch over, power loss), the radio is capable of restoring the active session in its current state as long as the session is active in the server.
Note: Power loss and power down are different activities, power down occurs when the user intentionally powers off the radio, power loss is when the battery dies or is removed from the unit.
Two-Factor Authentication
Two-Factor Authentication is an extension of existing
ARS and TMS operation. This feature allows you to authenticate yourself with a username, unit ID, password and passcode.
The purpose of this feature is to allow the sender of a text message to address a specific user of the radio, so the message is delivered to the user, not to the radio which may have any user using it at the time.
Secondly, this feature supports query authentication requirements so the query service knows which user originated a query.
You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message.
Note: A predefined username that is set more than the maximum allowed characters is an invalid name.
113
English
114
English
Logging in via the Two-Factor Authentication
1 Perform one of the following actions:
•
• Press the preprogrammed User Login button.
or to User, and press the Menu Select button directly below User.
The display shows the User Login screen.
2 Perform one of the following actions:
•
•
or to [ID Entry] and press the Menu
Select button directly below Edit. A blinking cursor appears. Use the keypad to type or edit a username. Press the Menu Select button directly below Ok to submit.
or to scroll through the list of predefined usernames. Press the Menu Select button directly below Sel to select the predefined username.
• Press and hold or to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Sel to select the predefined username.
If the selected predefined username has more than the maximum allowed characters, or an invalid character in it, the display shows momentary Invalid ID.
3 For radio enabled with Unit ID, Perform one of the following actions:
•
or to [UnitID Entry] and press the
Menu Select button directly below Edit. A blinking cursor appears. Use the keypad to type or edit a Unit ID. Press the Menu Select button directly below Ok to submit.
• or to scroll through the list of predefined
Unit IDs. Press the Menu Select button directly below Sel to select the predefined Unit ID.
• Press and hold or to scroll through the list of predefined Unit IDs at a fast scroll rate.
Press the Menu Select button directly below
Sel
to select the predefined Unit ID.
If the selected predefined Unit ID has more than the maximum allowed characters, or an invalid character in it, the display shows momentary
Invalid UnitID
.
4 Enter your password when you see a blinking cursor.
5 Press the Menu Select button directly below Logn or Ok.
If only one-factor is enabled, the display shows 1F logged
at the status. The login operation is complete.
If login fails, the display shows momentary Login failed
. The display returns to User Login screen.
6 For radio enabled with two-factor login, enter your passcode when you see a blinking cursor.
7 Press the Menu Select button directly below
Logn
.
The display shows In progress.
If the login fails, the display shows momentary 2F pscd failed
. Press the Menu Select button directly below Pscd to re-enter passcode. If successful, the display shows User Login screen with 2F logged in
status to indicate Two-Factor Authentication complete.
Logging out of Two-Factor Authentication
Note: Private data refers to all messages in the text messaging Inbox, Draft, and Sent folder. The next user is able to access the Inbox, Draft and Sent messages if private data is not deleted.
Radio which is successfully logged in to the secured system receives advertisement from the server that the access to the data for query is enabled.
1 Press the Menu Select button directly below
Logt
.
One of the following scenarios occurs:
• The display shows Clear private data?.
• If the Delete Messages On Session End feature is enabled, the display shows momentary Private data cleared.
2 Select Yes to clear all your private data or select
No
to keep your private data.
If you select Yes, the display shows momentary
Private data cleared
.
Sending a Query
This feature is available for radio users who have successfully logged in with the Two-Factor
Authentication. Query is a special form of Quick Text marked with a flag that is replied or dispatched in normal TMS message. The query template needs to
115
English
116
English be configured in the quick test list of the CPS. You can choose from the quick text list, including queries if present.
You shall receive a service advertisement message to indicate the Query is available after you have successfully logged in the radio with a Two-Factor
Authentication.
Note: The query server must be selected as the destination so that it can receive the query message and respond the query with text message. The query server must be an entry in the data user list in the
CPS.
1 Perform one of the following actions:
• To access this feature via a preprogrammed button, press the preprogrammed TMS Query button and proceed to Step
.
• To access this feature via the menu, proceed to the next step.
2
or to TMS and press the Menu Select button directly below TMS to access the TMS feature screen.
3 Perform one of the following actions:
• or to Compose and press the Menu
Select button directly below Sel.
• Press the Menu Select button directly below
Exit
to return to the Home screen.
4
or to Query and press the Menu Select button directly below Sel for a predefined message.
5
or to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message.
The message appears on the Compose screen, with a blinking cursor at the end of it.
6 Use the keypad to edit the message, if required.
7 Press the Menu Select button directly below
Optn
.
8
or to Send Message and press the Menu
Select button directly below Sel.
9 Perform one of the following actions:
• or to scroll through the address list and highlight the required address.
• or to [Other Recpnt] and press the
Menu Select button below Edit. A blinking cursor appears on the Enter Address screen.
Use the keypad to type the address entry.
10 Press the Menu Select button below Send or the
PTT button to send the message.
The display shows the Send Message screen and
Sending msg
.
If the message is sent, you hear a tone and the display shows Msg sent.
If the message is not sent, you hear a low tone, the display shows Send failed and returns to the main TMS screen.
Note: The server responds to your query with the required report in text messages.
You can append a priority status and/or a request reply to your message. See
Request Reply of a New Text Message
105 for more information.
Receiving a Query
You shall receive the information you have requested in TMS format.
When you receive a query, you hear a unique, highpitched chirp and the display shows the message icon flagged with “Priority”. The display shows momentary New msg.
To access the Inbox, press and hold the Data
Feature button or the preprogrammed TMS
Feature button or press the Menu Select button directly below TMS.
The display shows a list of aliases or IDs, with the sender of the latest received message on top.
Secure Operations
Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels.
Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message.
Note: On the APX 7000L, only AES encryption is supported for secure LTE data. In addition, for secure
LTE data a Virtual Private Network (VPN) is required.
117
English
118
Selecting Secure Transmissions
Turn the preprogrammed Secure/Clear switch to the secure position.
Note: If the selected channel is preprogrammed for clear-only operation, when you press the PTT button, you hear an invalid mode tone and the display shows Clear TX only.
The radio will not transmit until you set the
Secure/Clear switch to the clear position.
Selecting Clear Transmissions
Turn the preprogrammed Secure/Clear switch to the clear position.
Note: If the selected channel is preprogrammed for secure-only operation, when you press the PTT button, you hear an invalid mode tone and the display shows Secure TX only.
The radio will not transmit until you set the
Secure/ Clear switch to the secure position.
The radio can be configured to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details.
Managing Encryption
Loading an Encryption Key
Note: Refer to the key-variable loader (KVL) manual for equipment connections and setup.
1 Attach the KVL to your radio.
The display shows Keyloading, and all other radio functions, except for power down, backlight, and volume, are locked out.
2 Select the required keys and press the Menu
Select button directly below LOAD on the KVL.
This loads the encryption keys into your radio.
When the key has been loaded successfully, one of the following scenarios occurs:
• You hear a short tone for single-key radios.
• You hear an alternating tone for multikey radios.
Multikey Feature
This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm.
English
There are two types:
Conventional
Multikey
Trunked
Multikey
The encryption keys can be tied
(strapped), on a one-per-channel basis, through Customer
Programming Software. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups.
If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcementgroup basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure.
Selecting an Encryption Key
1
or to Key.
2 Press the Menu Select button directly below Key.
The display shows the last user-selected and stored encryption key, and the available menu selections.
3
or to scroll through the encryption keys or use the keypad to enter the number of the desired key.
4 Perform one of the following actions:
• Press the Menu Select button directly below
Sel
to save the newly selected key and return to the Home screen.
• Press , the PTT button, or the Menu Select button directly below Exit.
• Turn the 16-Position Select knob to exit.
Note: When the selected key is erased, you hear a momentary keyfail tone and the display shows
Key fail
.
119
English
120
English
When the selected key is not allowed, you hear a momentary illegal key tone and the display shows
Illegal key
.
Selecting a Keyset
This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio.
For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other.
Every channel to which one of the original keys was tied now has the equivalent new key instead.
1
or to KSet and press the Menu Select button directly below KSet.
The display shows the last user-selected and stored keyset, and the available keyset menu selections.
2
or to scroll through the keysets or use the keypad to enter the number of the desired keyset.
3 Press the Menu Select button directly below Sel to save the newly selected keyset.
The radio exits keyset selection and returns to the
Home screen.
Note: Press , the PTT button, or the Exit menu selection, or turn the 16-Position Select knob to exit this menu at any time without changing the keyset selection.
Erasing the Selected Encryption Keys
This feature allows you to erase all or selected encryption keys.
The following methods are options on how to erase the selected encryption keys. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Erasing the selected encryption keys via the radio menu: a) or to Eras and press the Menu Select button directly below Eras.
The display shows the last user-selected and stored encryption key, and the available menu selections.
b) or to the desired encryption key or use the keypad to enter the number of the desired key.
c) Press the Menu Select button directly below
Optn
.
The display shows the available key erase options.
d) or to the required option and press the
Menu Select button directly below Sel.
e) Select Erase all keys? or Erase single key?
by pressing the Menu Select button below Yes to erase the encryption key(s) in the radio.
You can return to the previous screen by pressing the Menu Select button below No.
• Erasing the single key in radios with the single-key option and erasing all keys in radios with the multikey option via the preprogrammed Top Side
(Select) button and Top (Orange) button: a) Press and hold the Top Side (Select) button.
b) While holding Top Side (Select) button down, press the Top (Orange) button.
The display shows Please wait. When all the encryption keys have been erased, the display shows All keys erased.
Note: Do not press the Top (Orange) button before pressing the Top Side (Select) button, unless you are in an emergency situation as this sends an emergency alarm.
Requesting an Over-the-Air Rekey (ASTRO
Conventional Only)
Ensure that the Unique Shadow Key (USK) is loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information.
This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user.
1
or to Reky.
121
English
122
English
2 Press the Menu Select button directly below
Reky
.
3 Perform one of the following actions:
• Press the PTT button to send the rekey request.
• Press the PTT button again, or the Home or
Emergency button, to exit the feature and transmit in normal mode.
If the rekey operation fails, you hear a bad-key tone and the display shows Rekey fail.
Note: The rekey operation failure indicates that your radio does not contain the Unique Shadow
Key (USK).
MDC Over-the-Air Rekeying (OTAR) Page
This feature allows you to view or define MDC Overthe-Air Rekeying (OTAR) features. It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to
Rekey Requests, OTAR transmissions include
Delayed Acknowledgements, and Powerup
Acknowledgements.
Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly.
Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
Infinite UKEK Retention
This feature enables Unique Key Encryption Key
(UKEK) to be permanently stored in the radio even when all of the encryption keys is erased. Without this
UKEK key, the radio could not be over the air rekeyed.
Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
Hear Clear
Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
There are two components of Hear Clear.
Companding Reduces the channel noise, e.g.
OTA transmission, that is predominantly present in UHF2 and
900 MHz channel with the following features.
Compressor Reduces the background noise flow and the speech signal at transmitting radio.
Expander
Expands the speech while the noise flow remains the same at receiving radio.
Random FM
Noise
Canceller
(Flutter
Fighter)
Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-
Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal.
The Random FM Noise Canceller operates only in receive mode.
Security
Radio Lock
This feature changes your radio to a more robust security system that protects the use of the secure encryption keys.
If this feature is enabled in your radio by a qualified radio technician, when you turn the radio on, the display shows Radio locked.
Unlocking Your Radio
1 Enter your numeric password.
Secure-equipped radios – 6 to 8 characters.
Clear radios – 0 to 8 characters.
2 Perform one of the following actions:
• Press the Menu Select button directly below
Sel
to enter the code.
• Press the Menu Select button directly below
Del
to delete any unwanted characters.
123
English
124
English
• Press the Menu Select button directly below
Cncl
to exit the feature.
If the password is correct, the radio unlocks.
If the password is incorrect, the display show
Incorrect password
and the radio remains locked.
If you enter three incorrect passwords in a row, the display shows Deadlock. Turn the radio off and then on, and begin again at Step
.
Important: For Secure Radios Only – After a total of 17 consecutive incorrect passwords (turning the radio off and on does not reset this number), the radio erases all of its encryption keys and shows
Deadlock
. See a qualified radio technician.
If you forget the password, enter ******** to erase all keys and revert the password in the radio back to the default password of 01234567.
Changing Your Password
1
or to Pswd.
2 Press the Menu Select button directly below
Pswd
.
The display shows Change Password screen.
3
or to Unlock Pswd.
4 Press the Menu Select button directly below Sel.
5 Enter the old password.
6 Press the Menu Select button directly below Ok.
7 Enter the new password.
8 Press the Menu Select button directly below Sel.
9 Re-enter the new password.
10 Press the Menu Select button directly below Sel.
The password is updated.
If the two passwords do not match, repeat Steps
through
.
Note: If you enter three incorrect old passwords, the radio exits the password feature. You cannot access this feature again until you turn the radio off and on.
Changing Your Tactical Inhibit Password
1
or to Pswd.
2 Press the Menu Select button directly below
Pswd
.
The display shows Change Password screen.
3
or to Tactical Inh Encode Pswd.
4 Press the Menu Select button directly below Sel.
5 Enter the old password.
6 Press the Menu Select button directly below Ok.
7 Enter the new password.
8 Press the Menu Select button directly below Sel.
9 Re-enter the new password.
10 Press the Menu Select button directly below Sel.
The password is updated.
If the two passwords do not match, repeat Steps
through
.
Note: If you enter three incorrect old passwords, the radio exits the password feature. You cannot access this feature again until you turn the radio off and on.
Enabling or Disabling the Radio Lock Feature
(Secure Radios Only)
This feature allows you to enable or disable the radio lock feature. It is programmable by a qualified radio technician.
1
or to Logf.
2 Press the Menu Select button directly below
Logf
.
One of the following results occur.:
• The display shows Pswd enabled, indicating that the radio lock feature is enabled.
• The display shows Pswd disabled, indicating that the radio lock feature is disabled.
125
English
126
Radio Stun and Kill
Radio Stun
This feature allows you to stun another radio by sending an over the air command using the menu on your radio. This feature prevents an unauthorized user from using the radio. Once the radio is stunned, a password is required to re-activate the stunned radio.
Using Radio Stun
1
or to Stun.
2 Press the Menu Select button directly below
Stun
.
The display shows Enter Password.
3 Use the keypad to enter your Tactical Inhibit
Encode Password.
4 Press the Menu Select button directly below Ok.
The display shows radio Contact IDs.
5 Perform one of the following actions:
• or to the required ID.
English
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
• Use the keypad to enter the required ID.
• Press the Menu Select button directly below
Send
to initiate command.
If the receiving radio does not have encryption key to decrypt the received command, your radio display shows Ack received.
If the receiving radio does not have encryption key to decrypt the received encrypted command, your radio display shows Decrypt failed.
If the receiving radio is powered off, your radio display shows No Acknowledgement.
Once the receiving radio received the command, its screen locked and request for password.
Note: To un-stun a radio, follow the procedure in
Radio Kill
This feature allows you to render your radio or another radio inoperable if the radio is misplaced or lost. When a radio is killed, the display turns blank and all functions of the radio are not usable.
The killed radio can only be recovered from KILL with a special device. Consult an authorized and qualified technician for details.
Using Remote Kill to Kill Another Radio
Remote Kill allows you to render another radio inoperable by sending an over the air command using the menu on your radio.
1
or to Kill.
2 Press the Menu Select button directly below
Kill
.
The display shows Enter Password.
3 Use the keypad to enter your Tactical Inhibit
Encode Password.
4 Press the Menu Select button directly below Ok.
The display shows radio Contact IDs.
5 Perform one of the following actions:
• or to the required ID.
• Press the Menu Select button directly below
LNum
to go to the last number dialed.
• Use the keypad to enter the required ID.
• Press the Menu Select button directly below
Send
to initiate command.
If the receiving radio received the command, your radio display shows Ack received.
If the receiving radio does not have encryption key to decrypt the received encrypted command, your radio display shows Decrypt failed.
If the receiving radio is powered off or already killed, your radio display shows No
Acknowledgement
.
Once the receiving radio received the command, its screen turns blank, the killed radio is inoperable.
Using Direct Kill to Kill Your Own Radio
Direct Kill allows you to make your own radio inoperable.
Press and hold the Top Side button then press the Orange button until the display turns blank and becomes inoperable.
Global Positioning System (GPS)
This feature uses information from the Global
Positioning System (GPS) satellites orbiting the Earth
127
English
128
to determine the approximate geographical location of your radio, expressed as latitude and longitude or
MGRS format per request from customers. The availability and accuracy of this location information
(and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature.
For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky.
Once GPS is enabled, the radio displays the GPS icon on the screen. The dispatcher can always request the system to determine the real-time location coordinates of the radio.
GPS Operation
The GPS technology uses radio signals from earth orbiting satellites, to establish the location coordinates, maximizing your view of clear unobstructed sky is essential for optimum performance.
Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of
English your radio will not work. Such situations include but are not limited to:
• Underground locations
• Inside of buildings, trains, or other covered vehicles
• Under any other metal or concrete roof or structure
• Between tall buildings or under dense tree-cover
• In temperature extremes outside the operating limits of your radio
Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher.
Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites.
Note: Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20
meters from your actual location, but sometimes farther away.
The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of
Defense GPS user policy and the Federal Radio
Navigation Plan. These changes may affect the performance of the GPS feature on your radio.
GPS Performance Enhancement
Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites.
To maximize the ability of your radio to determine a fix, take note of the following guidelines:
• For your initial fix, hold the radio in the face position.
• Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky.
The Outdoor Location Feature (Using GPS)
This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air.
Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio.
The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted.
The following table shows the differences between programmable waypoints and preprogrammed waypoints.
Programmable
Waypoints
User-configurable location coordinates.
Preprogrammed
Waypoints
Fixed location coordinates:
• Home
• Emergency
• Last Known Location
• Destination
129
English
Programmable
Waypoints
Only the alias is editable, not the coordinates.
Coordinates can be deleted one at a time, or all at once.
Preprogrammed
Waypoints
The Home and
Destination coordinates are editable.
Coordinates cannot be deleted.
130
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You hear the Menu
Inactive Exit Tone upon feature exit.
Military Grid Reference System (MGRS) Coordinates
This feature can only be enabled through CPS configuration. When the MGRS coordinate is enabled, all location coordinates are displayed in
MGRS format, including the editable locations in
GPS.
Accessing the Outdoor Location Feature
Note: An ON radio menu may be present on the
Location menu screen if it is preprogrammed by the dealer or system administrator.
English
Press the preprogrammed GPS button to toggle the
Outdoor Location feature to on or follow the following procedure to access this feature via the radio menu.
1
or to Loc.
2 Press the Menu Select button directly below Loc.
The display shows Location off.
3 Perform one of the following actions:
• To obtain a location fix, press the Menu Select button directly below On .
• Press the Menu Select button directly below
Optn
. or to Turn On GPS and press the
Menu Select button directly below Sel.
The front display shows the MGRS or latitude/ longitude location, time, and date of the last successful location fix.
4 To obtain a new location fix, press the Menu
Select button directly below Rfsh.
The top line temporarily displays Please wait while the new location is being determined. While the new location is being determined, the location signal can be a solid or blinking icon.
Once the location coordinates are fixed, the display shows the current location along with the
UTC (Zulu) time and date that the location fix was obtained.
The location coordinates are updated automatically every 5 seconds while the location signal is present.
If the radio fails to get a location fix, the display shows No service and returns to the previous display.
5 To return to the Home screen, press , the PTT button, the preprogrammed GPS button or the
Menu Select button directly below Exit.
Saving a Waypoint
Ensure that your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2 Perform one of the following actions:
•
or to Save as Waypt and press the
Menu Select button directly below Sel.
•
•
or to Save as Home and press the Menu
Select button directly below Sel and proceed to
.
or to Save as Dest. and press the
Menu Select button directly below Sel and
.
A blinking cursor appears in the screen.
3 Use the keypad to edit the auto-generated waypoint, if required or press the Menu Select button directly below Cncl to return to the Location main screen.
4 Press the Menu Select button directly below Ok once you are done.
One of the following scenarios occur:
• The display shows Current loc saved as
<Waypoint name>
.
• The display shows Current loc saved as
[Home]
.
• The display shows Current loc saved as
[Destination]
.
131
English
132
5 To return to the Home screen, press , the PTT button, the preprogrammed GPS button or the
Menu Select button directly below Exit.
Viewing a Saved Waypoint
Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2
or to Waypoints and press the Menu Select button directly below Sel.
The display shows a list of waypoints.
3 Perform one of the following actions:
•
• or to scroll through the list.
or to select a waypoint to view the location information in full.
4 Press the Menu Select button directly below
Optn
.
5 To view the MGRS or latitude/longitude location, time and date of the selected waypoint, or to
View
and press the Menu Select button directly below Sel.
6 To return to the previous screen, press the Menu
Select button directly below Back, or to return to the Home screen, press , the PTT button, or the preprogrammed GPS button.
Editing the Alias of a Waypoint
Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2
or to Waypoints and press the Menu Select button directly below Sel.
The display shows a list of waypoints.
3
or to the required saved waypoint, and press the Menu Select button directly below Optn.
4
or to Edit name and press the Menu Select button directly below Sel.
A blinking cursor appears in the Edit Name screen.
English
5 Use the keypad to edit the alias.
6 Perform one of the following actions:
• Press the Menu Select button directly below
Ok
once you are done.
• Press the Menu Select button directly below
Cncl
to return to the Waypoints main screen.
7 The display shows <Waypoint name> Updated and the radio returns to the Waypoints main screen.
8 Perform one of the following actions:
• Press the Menu Select button directly below
Back
to return to the previous screen.
• Press , the PTT button, or the preprogrammed GPS button to return to the
Home screen.
Editing the Coordinates of a Waypoint
Note: Only the preprogrammed coordinates of Home and Destination can be edited by the user.
Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2
or to Waypoints and press the Menu Select button directly below Sel.
The display shows a list of waypoints.
3 Perform one of the following actions:
•
•
or to [Home] and press the Menu Select button directly below Optn.
or to [Destination] and press the
Menu Select button directly below Optn.
4
or to Edit location and press the Menu
Select button directly below Sel.
The first number blinks.
5 Utilize the following control buttons to select the number/coordinates if required, then press the
Menu Select button directly below Edit to change the number/coordinates.
• Press to move to the previous number/ coordinates.
• Press to move back to the next number/ coordinates.
133
English
134
English
A blinking cursor appears in the Edit Location screen.
6 Utilize the following control buttons or menu to change the number/coordinates if required then press the Menu Select button directly below Ok once.
• Press to move one space to the left.
• Press to move one space to the right.
• Press the Menu Select button directly below
Del
to delete any unwanted characters.
• Press the Menu Select button directly below
Cncl
to return to the previous screen
7 Press the Menu Select button directly below Ok once complete setting up the new Home or
Destination.
One of the following scenarios occurs:
• The display shows [Home] Updated and the radio returns to the Waypoints main screen.
• The display shows [Destination] Updated and the radio returns to the Waypoints main screen.
Deleting a Single Saved Waypoint
Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2
or to Waypoints and press the Menu Select button directly below Sel.
The display shows a list of waypoints.
3 Perform one of the following actions:
• or to the required saved waypoint, and press the Menu Select button directly below
Optn
. or to Edit name and press the
Menu Select button directly below Del.
• Press the Menu Select button directly below
Del
.
4 The display shows Delete <Waypoint name>
Confirm?
.
5 Press the Menu Select button directly below Yes to delete the waypoint or press the Menu Select button directly below No to return to the Waypoints main screen.
The display shows <Waypoint name>deleted .
Deleting All Saved Waypoints
Ensure your radio shows the current location on the screen.
Note: You cannot delete any of the preprogrammed waypoints.
1 Press the Menu Select button directly below
Optn
.
2
or to Waypoints and press the Menu Select button directly below Sel.
The display shows a list of waypoints.
3
or to the required saved waypoint, and press the Menu Select button directly below Optn.
4
or to Delete All and press the Menu
Select button directly below Sel.
The display shows Delete All saved waypnts
Confirm?
.
5 Press the Menu Select button directly below Yes to delete all waypoints or press the Menu Select button directly below No to return to the Waypoints main screen.
The display shows All saved waypnts deleted.
Measuring the Distance and Bearing from a Saved
Waypoint
Ensure your radio shows the current location on the screen.
1 Press the Menu Select button directly below
Optn
.
2
or to Dist frm here and press the Menu
Select button directly below Sel.
The display shows a list of waypoints.
3
or to the required waypoint and press the
Menu Select button directly below Sel.
The display shows the distance and bearing from the current to the selected coordinates.
Location Feature in Emergency Mode
When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the Home (default) screen so
135
English
136
that you can see which channel the emergency signal is going out on.
However, you may re-enter the Location menu while still in emergency mode, provided that Silent
Emergency has not been activated.
If you have turned Location off using the ON/OFF menu key, it automatically turns back on when
Emergency is activated.
If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known
Location waypoints, respectively.
Peer-Location on the Display (ASTRO Conventional only)
This feature is only available for radio-to-radio voice transmissions, dispatch call and selective call in conventional ASTRO system. For radio-to-radio transmission, in order to allow the radio to show peerlocation, the voice should be directly sent from one radio to another radio without passing through any infrastructure facility such as repeaters, phone or
DVRS system. Both the transmitting radio and receiving radio must be configured to enable them to send and/or receive the GPS coordinates. You can
English check with your nearest qualified technician for more details.
Note: If the receiving radio is operating in a Mixed
Mode channel, only if its voice transmission is via conventional ASTRO system then it can receive the location coordinates of its peers.
This feature is also operable in a Scan Active channel or Scan Talkback channel.
Upon receiving a voice transmission with GPS coordinates enabled on the receiving radio, the display shows the coordinates available in full or in short coordinates. There are two different formats available. Refer to the following list for the details shown in the Peer-Location quick text. Consult your agent to pick the best format to configure to your radio.
Full location coordinates
• PTT ID (This is optional.)
• Longitude and latitude
• Relative distance or direction.
Short location coordinates
• PTT ID (This is optional.)
• Longitude and latitude
Note:
If the transmitting radio is stale at its location after a period of time, the receiving radio display shows
ID:<PTT ID> Last Knwn Loc: <Coordinates>
.
The ID:<PTT ID> and <distance> are optional details depending on the requirements of usage.
If the transmitting radio does not have GPS or the receiving radio could not decode the GPS signal of the received signal, the receiving radio display shows
ID:<PTT ID> Unknown Loc
. The PTT ID is optional to be shown on the display per requirements of usage.
Geofence (ASTRO 25 Trunking System)
Geofence is a virtual perimeter based on the GPS to define a geographical area on earth.
When the radio enters the predefined Geofence area, your radio receives the Dynamic Regroup command from the system and immediately connects to a
Dynamic Regroup talkgroup. The radio display shows the new selected Dynamic Regrouped talkgroup with green intelligent light for your attention.
On top of that, additional features are Voice
Announcement of the new channel, and also direct content display of a text message to indicate that you are currently at Geofence area. Check with your nearest qualified technician on the requirements for these enhancements to work in Geofence.
Any new text messages received at Geofence shall have its content displayed immediately on the radio display.
Note: If the radio is set up in DVRS, only mobile radio is supported for this feature.
Entering the Geofence Area
The Voice Announcement and TMS display in this feature are optional. They must be configured to enable you to hear and see these indicators.
When the radio enters a Geofence area, the radio immediately sends a message ACK back to the system.
The radio searches the current zone for the channel with same talkgroup assigned as the Dynamic
Talkgroup and also with same system ID of current trunk system. Once matched, the radio display shows the first matched and connected channel alias.
137
English
138
English
If there is no channel with matched Talkgroup ID and trunk system ID, the radio display shows the channel alias of <DYNAMIC talkgroup>.
Once the radio is connected, you hear a dynamic regroup tone, the radio display shows <DYNAMIC channel>
with temporary green color intelligent backlight and you hear a Voice Announcement.
Note: When the radio loss the GPS signal the GPS icon blinks and the radio sounds two high-pitched tones repetitively to indicate GPS fails to operate. The radio display shows red intelligent light.
Note: If the first matched channel is not configured with Voice Announcement, no Voice Announcement is played.
The system sends a message to your radio. The radio display shows a direct text message content without any user operation. This message indicates you are currently present in a Geofence area. This
TMS remains open on the display until user presses exit/home to exit this screen.
Note: If there is another incoming text message before you exit the previous message, the message screen shall be refreshed to show the latest message.
The following procedure guides you to exit the text message received.
Press the Menu Select button below Exit or to return to Home screen.
The other operations are the same as normal dynamic regroup command.
When the radio exits the Geofence area, your radio reverts to original channel or newly assigned talkgroup. The radio display shows the new channel together with Voice Announcement to indicate the changes. Voice Announcement of the new channel only works if that channel is configured with Voice
Announcement.
Trunking System Controls
Using the Failsoft System
The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel.
During failsoft operation, your radio transmits and receives in conventional operation on a
predetermined frequency. You hear a mediumpitched tone and the display shows Failsoft.
When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation.
To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure.
1 Rotate the Mode Knob to change to a different repeater frequency.
2 Press the PTT button to talk, and release the button to listen.
Out-of-Range Radio
When your radio goes out of the range of the system, it can no longer lock onto a control channel.
You hear a low-pitched tone and/or the display shows the currently selected zone/channel combination and
Out of range
. Your radio remains in this out-ofrange condition until it locks onto a control channel, it locks onto a failsoft channel, or it is turned off.
Site Trunking Feature
If the zone controller loses communication with any site, that site reverts to site trunking.
The display shows the currently selected zone/ channel combination and Site trunking.
Note: When this occurs, you can communicate only with other radios within your trunking site.
Locking and Unlocking a Site
This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites.
This feature should be used with caution, since it inhibits roaming to another site in a wide-area system.
You can toggle the lock state between locked and unlocked by pressing the preprogrammed Site Lock/
Unlock button.
Follow the following procedure to lock and unlock a site via the radio menu.
1
or to Site.
2 Press the Menu Select button directly below
Site
.
139
English
140
3 Perform one of the following actions:
• To lock the site, press the Menu Select button directly below Lock. The display shows Site locked
.
• To unlock the site, press the Menu Select button directly below Unlk. The display shows
Site unlocked
.
The radio saves the new site lock state and returns to the Home screen.
Site Display and Search Button
The Site Display and Site Search button allows you to view the name of the current site or force your radio to change to a new one.
Viewing the Current Site
Perform one of the following actions:
•
• Press the preprogrammed Site Displ/Srch button.
or to RSSI and press the Menu Select button directly below RSSI.
The display shows momentary the name of the current site and its corresponding received signal strength indicator (RSSI).
Changing the Current Site
Perform one of the following actions:
• Press and hold down the preprogrammed Site
Displ/Srch button.
• Press and hold down the Menu Select button directly below RSSI.
You hear a tone and the display shows momentary Scanning site.
When the radio finds a new site, it returns to the
Home screen.
Mission Critical Wireless - Bluetooth
®
-
This feature allows your radio to extend its functionality by connecting to external proprietary
Motorola accessories.
Note: It is recommended to use Motorola proprietary
Mission Critical Wireless (MCW) devices with APX radios during Mission Critical operations as other
English
Bluetooth
®
devices may or may not meet the mission critical standard.
Your radio must be preprogrammed to allow you to use this feature.
The default setting for Bluetooth-enabled radio is
Bluetooth ON. See
on page
142 to turn the Bluetooth OFF.
Currently your radio supports the following Bluetooth devices or profiles.
• Headset (HSP)
• Dial Up Networking (DUN)
• Personal Area Networking (PAN)
• Serial Port (SPP)
Note: APX 7000L radio does not support Bluetooth
Commercial of the Shelf (COTS) devices or the
Personal Area Network (PAN) data profile.
APX 7000L only works with Motorola MCW devices.
Turning the Bluetooth On
The following methods are options on how to turn the
Bluetooth on. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turning the Bluetooth on via the radio menu BT: a) or to BT. To access the Bluetooth feature screen, press the Menu Select button directly below BT.
b) or to Status and press the Menu Select button directly below On.
The display shows Status On, and appears.
If Bluetooth fails to launch, the display shows
Bluetooth on failed
.
c) To return to the Home screen, press the Menu
Select button directly below Exit.
• Turning the Bluetooth on via the preprogrammed button: a) Press the preprogrammed button to turn on the
Bluetooth.
You hear a short, medium-pitched tone. The display shows momentary Bluetooth on, and
appears.
141
English
142
If Bluetooth fails to launch, the display shows
Bluetooth on failed
.
Turning the Bluetooth Off
The following methods are options on how to turn the
Bluetooth off. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turning the Bluetooth off via the radio menu BT: a) or to BT. To access the Bluetooth feature screen, press the Menu Select button directly below BT.
b) or to Status and press the Menu Select button directly below Off.
The display shows Status Off, and disappears.
c) To return to the Home screen, press the Menu
Select button directly below Exit.
• Turning the Bluetooth off via the preprogrammed button: a) Press the preprogrammed button to turn off the
Bluetooth.
You hear a short, medium-pitched tone. The display shows momentary Bluetooth off and
disappears.
Re-Pair Timer
There are two options for configuring the Bluetooth pairing type of the radio. The type defines the duration the radio and the accessory retain the pairing information.
Immediate (For MCW accessories only.) When the radio and/or device is turned off after pairing, the keys are lost. Due to this, when your radio and your device are turned back on, they are unable to reconnect. The user must re-pair the devices to re-establish a new set of
Frequency-Motorola Proximity Pairing
on page 145 and
Infinite
(For all Bluetooth devices.) When the radio and/or device are turned off after pairing, keys are not lost. When the radio and the device are turned back
English
Re-Pair
Timer
Options
Immediate
(For MCW
Accessories only) on, they can resume the Bluetooth connection without user intervention.
Re-Pair Timer Scenarios
• When the radio is powered off, pairing key is lost immediately, and accessory attempts to pair again. If pairing is unsuccessful within the Drop Timer value, the accessory automatically powers off.
• When the accessory is powered off, all keys are lost immediately, and the user must re-pair the devices.
• When the device loses Bluetooth connection, the device will attempt to re-establish Bluetooth
Connection within the Drop
Timer value.
Re-Pair
Timer
Options
Re-Pair Timer Scenarios
Infinite (For all
Bluetooth devices)
• When the radio is powered off, the accessory attempts to reestablish the Bluetooth
Connection for a period of time depending upon the Drop Timer value. If the device fails to reconnect within the period, the accessory then powers off.
Bluetooth Drop Timer
The Bluetooth Drop Timer has two different settings and functions, depending upon the selection of the
Re-Pair Timer.
Re-Pair Timer
Options
Immediate
(For MCW
Accessories only)
Description
0 – 15 minutes programmable buffer time to re-establish the
Bluetooth Connection when the
Bluetooth signal is out of range.
143
English
144
English
Re-Pair Timer
Options
Description
Infinite (For all
Bluetooth devices)
If either device powers off, the pairing keys are immediately cleared from both devices and the devices must re-pair.
This Timer only applies to the accessory. The programmable timer choices are: 0 – 15 minutes, 2 hours, 4 hours or 8 hours.
Do note there are exceptions for
Operation Critical Wireless (OCW) headset and PTT which are preprogrammed to 8 hours.
This is a "stay alive" time that the accessory will remain on without the device reconnecting before powering off. The radio will remain
on until the user powers the radio
off. The radio and accessory will remain paired indefinitely. Once the device re-connect, the timer is reset.
The radio could not control the Drop Timer of
Personal Area Networking (PAN), Dial-Up Networking
(DUN), Commercial Off- The-Shelf (COTS) and data services. It is depends on the specifications of these external devices.
Check with your dealer or system administrator for more information about these timers.
To establish the Bluetooth Connection, see
Pairing with Low Frequency-Motorola Proximity Pairing (LF-
on page 146 .
Pairing with Low Frequency-Motorola Proximity Pairing
(LF-MPP) Feature
A
Ensure that Bluetooth feature of your radio is on and the Bluetooth tones are enabled.
Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
The range of Bluetooth operation is 10 meters line-ofsight communication. This is an unobstructed path between the location of the signal transmitter (your radio) and the location of the receiver (your device or accessory).
Obstacles that can cause an obstruction in the line-ofsight include trees, buildings, mountains, cars and etc.
It is not recommended that you leave your radio behind and expect your accessory to work with a high degree of reliability when they are separated.
At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken". To correct this problem, simply position the accessory and radio closer to each other (within the 10 meter defined range) to re-establish clear audio reception.
Note: Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk Time power consumption, not the Standby Time consumption.
Turn on the accessory. Then place it close to your radio aligning the Bluetooth Pairing Location ( ) on the radio to the Bluetooth Pairing Location (a blue dot) on the accessory.
145
English
146
English
If the pairing process is successful, you hear an incremental-pitched tone. The radio begins to connect to the device.
If the pairing process fails, you hear a short, lowpitched tone. The display shows Bluetooth pairing failed
. Repeat this step.
The radio tries to establish connection with the device once paired.
Note: If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows <Device
Type> unpaired
. Repeat this step to re-initiate the pairing process.
If the connection is successful, you hear an incremental-pitched tone. The display shows <Device
Type> connected
and the Bluetooth icon turns from
to .
If the radio has the pairing record of the device and the connection fails, you hear a short, low-pitched tone. The display shows <Device Type> connect failed
.
Radio Indications of Lost Bluetooth Connection
The radio shows when the device has a Bluetooth connection. Below is the scenario and radio indications when the connection is interrupted.
The starts blinking for up to 10 seconds. You hear a decremental-pitched tone. The display shows
<Device Type>
alternating with disconnected.
If the Bluetooth device successfully re-connects before the Bluetooth 10 second Re-Connection Timer expires, the display shows momentary <Device
Type> connected
, and stops blinking, or if the
Bluetooth device fails to re-connect within 10 seconds, the blinking is replaced by a persistent
.
Standard Pairing Feature
Note: Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk time power consumption, not the Standby time consumption.
The Bluetooth Standard Pairing feature enables your
Bluetooth enabled radio to search for other Bluetooth enabled and discoverable device. Once the device is discovered, you can initiate your radio to send a pairing request to pair with the device.
This feature also enables your Bluetooth enabled radio to be visible to another Bluetooth enabled device and receive request to pair from other device.
The Standard Pairing feature supports pairing
Authentication Personal Pairing Number or PIN which ensure your radio recognizes the correct device to pair. The PIN must be exchanged with the radio or the device before the pairing completes. Your radio prompts for the Authentication PIN when needed.
Refer to your device’s manual for details about the
Bluetooth Authentication PIN of your device if needed.
Searching and Pairing the Bluetooth Device
Ensure the Bluetooth on your device is turned to On and is set to Discoverable in order to enable your radio to detect your device in Bluetooth.
Bluetooth Search in Bluetooth Standard Pairing method is used to scan for other Bluetooth devices nearby. It is set to off by default.
1 Perform one of the following actions:
•
• Press the preprogrammed Bluetooth Search button .
or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen. or to Search Devices and press the Menu Select button directly below On.
If successful, the display shows Searching for
BT devices
followed by the names of Bluetooth devices found, if any. When the search timer expires, Available Dev screen shows a list of
Bluetooth devices found. To stop the search before the search timer expires, press the preprogrammed Bluetooth Search button or the
Menu Select button below Stop.
147
English
148
English
If the feature fails to initiate, the radio sounds a short, low-pitched tone. The screen shows BT
Search failed
. Press the Menu Select button below Back to return to Bluetooth feature screen, or press or the Menu Select button below
Exit
to return to Home screen.
2
or to the device name and press the Menu
Select button directly below Sel to connect to the device.
The radio starts pairing to the device.
To continue with Bluetooth pairing, please see
Pairing with Low Frequency-Motorola Proximity Pairing (LF-
Turning Bluetooth Visibility On
Turning Bluetooth visibility to on enables other
Bluetooth devices to search for your radio. The visibility of the Bluetooth is set to off by default.
The following methods are options on how to turn
Bluetooth visibility on. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turn Bluetooth visibility on via radio menu BT: a) or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
b)
or to Visibility and press the Menu
Select button directly below On.
The status changes to Visible to all.
Visibility mode is enabled.
When the timer expires, the status changes to
Visibility failed
. Repeat the procedure to turn Bluetooth visibility on.
• Turn Bluetooth visibility on via the preprogrammed button.
a) Press the preprogrammed button to enable the
Bluetooth visibility feature.
You hear a short, medium-pitched tone. The display shows momentary Visible to all.
Visibility mode is enabled.
When the timer expires, the display shows momentary Visibility failed. Repeat the procedure to turn Bluetooth visibility on.
Note: Press the preprogrammed to toggle the
Bluetooth visibility on or off.
Receiving Pairing Request from other Devices
When your radio receives a pairing request from other device, the display shows <Device Friendly
Name>pair request
.
Press the Menu Select button below Ok to accept or Cncl to refuse pairing request.
Turning Bluetooth Visibility Off
Ensure that Bluetooth Visibility is turned on.
The following methods are options on how to turn
Bluetooth visibility off. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turn Bluetooth visibility off via radio menu BT: a) or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
b) or to Visibility and press the Menu
Select button directly below Off.
The display shows Visibility Off.
When the timer expires, the status changes to
Visibility off failed
. Repeat this step to turn Bluetooth visibility off.
c) To return to the Home screen, press the Menu
Select button directly below Exit.
• To disable the Bluetooth visibility, press the preprogrammed button.
You hear a short, medium-pitched tone. The display shows momentary Visibility Off.
Visibility mode is disabled.
When the timer expires, the status changes to
Visibility off failed
. Repeat this step to turn Bluetooth visibility off.
PIN Authentication in Pairing
For the security of your radio, Bluetooth Pairing PIN feature is designed to enable your radio to verify the correct device to pair before initiating the pairing.
Authentic PIN is used for the verification.
Note: The compare PIN authentication method is only applicable for Bluetooth version 2.1 and above.
149
English
150
English
Pairing the Authentication PIN when Receiving a
Pairing Request
1 When the radio display shows <Device Friendly
Name> pair request
, perform one of the following actions:
• To accept, press the Menu Select button below Ok.
• To reject, press the Menu Select button below
Cncl
Your radio only supports HSP, DUN, PAN and
SPP Bluetooth profiles.
When the pairing timer expires, the display shows
<Device Friendly Name> pair canceled
and return to Home screen.
If you choose to accept the pairing process, the display shows Compare PIN: XXXXXX.
If you choose to reject the pairing process, the display shows Cancel pairing in progress...
followed by <Device Friendly
Name> pair canceled
and return to Home screen.
2 Perform one of the following actions when the display shows Compare PIN: XXXXXX.:
• Press the Menu Select button below Ok if the
PIN is correct.
• Press the Menu Select button below Cncl to reject if the PIN number is incorrect. The display shows Cancel pairing in progress...
followed by <Device Friendly
Name> pair canceled
and return to Home screen.
When the PIN authentication timer expires, the display shows <Device Friendly Name>pair canceled
and return to Home screen.
If successful, the display shows Pairing in progress....
, <Device Friendly Name> paired
followed by <Device Friendly
Name>connected
.
If unsuccessful, one of the following scenarios will occur:
• The display shows <Device Friendly Name> pair failed
(if the pairing timer expires).
• The display shows <Device Friendly Name> connect failed
(if the connecting timer expires).
If the PIN is correct but the profiles are not supported, the display shows BT profiles not supported
. The display returns to Home screen.
Pairing the Authentication PIN with the Generated
Numeric PIN
on page 147 to search for available
Bluetooth devices. Start pairing with the
Authentication PIN by following the steps described next.
1
or to the required device. Press the Menu
Select button directly below Sel to initiate pairing.
Your radio only supports HSP, DUN, PAN and
SPP Bluetooth profiles.
If successful, the display shows Pairing in progress...
followed by a randomly generated numeric PIN, Compare PIN: XXXXXX.
If unsuccessful, the display shows BT profiles not supported
. The display returns to Available
Dev screen.
2 Press Ok to continue pairing the radio and the device.
The pairing process can be canceled by pressing the Menu Select button below Cncl.
If successful, the display shows Pairing in progress
,<Device Friendly Name> paired,
Connecting in progress...
followed by
<Device Friendly Name>connected
. The display returns to the Bluetooth feature screen.
If unsuccessful, one of the following scenarios will occur:
• The display shows <Device Friendly Name> pair failed
(if the PIN numbers are different).
• <Device Friendly Name> connect failed
(if the connection fails).
The display returns to Available Dev screen.
151
English
152
English
Pairing the Authentication PIN by Manually
Keying in the Same PIN
Follow the procedure in
on page 147 to search for available
Bluetooth devices. Start pairing with the
Authentication PIN by following the steps described next.
1
or to the required device. Press the Menu
Select button directly below Sel to initiate pairing.
Your radio only supports HSP, DUN, PAN and
SPP Bluetooth profiles.
If successful, the display shows Pairing in progress...
followed by a request for PIN number. A blinking cursor appears below the
Enter PIN:
.
If unsuccessful, the display shows BT profiles not supported
. The display returns to Available
Dev screen.
2 Use the keypad to enter the PIN. Press to move one space to the left. Press to move one space to the right. Press the Menu Select button directly below Del to delete.
3 Press Ok to continue pairing the radio and the device. Enter the same PIN number on the device.
The pairing process can be canceled by pressing the Menu Select button below Cncl.
If successful, the display shows Pairing in progress
,<Device Friendly Name> paired,
Connecting in progress...
followed by
<Device Friendly Name>connected
. The display returns to the Bluetooth feature screen.
If unsuccessful, one of the following scenarios will occur:
• The display shows <Device Friendly Name>
PIN auth fail
(if the PIN numbers are different).
• <Device Friendly Name> connect failed
(if the connection fails).
The display returns to Available Dev screen.
Turning On the Bluetooth Audio (Routing the Audio from the Radio to the Headset)
The following methods are options on how to turn on the Bluetooth audio. The result of all the methods is the same. You can use the options interchangeably
depending on your preference and the programmed functions.
• Turning on the Bluetooth audio via radio menu BT: a) or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
b) or to Bluetooth spkr and press the
Menu Select button directly below On.
The display shows On.
c) To return to the Home screen, press the Menu
Select button directly below Exit.
• Turning on the Bluetooth audio via the preprogrammed button: a) To route the audio routing from the radio to the headset, short press the preprogrammed button.
You hear a short, medium-pitched tone. The display shows Headset on.
Turning Off the Bluetooth Audio (Routing the Audio from the Headset to the Radio)
The following methods are options on how to turn off the Bluetooth Audio. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turning off the Bluetooth audio via radio menu BT: a) or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
b) or to Bluetooth spkr and press the
Menu Select button directly below Off.
The display shows Off.
c) To return to the Home screen, press the Menu
Select button directly below Exit.
• Turning off the Bluetooth audio via the preprogrammed button: a) To route the audio routing from the headset to the radio, press the preprogrammed button.
You hear a short, medium-pitched tone. The display shows Speaker on.
Adjusting the Volume of the Radio from Bluetooth
Audio Device
Ensure that the Bluetooth audio device is connected to the radio.
153
English
154
Your radio can only control the volume of MCW and
OCW Bluetooth enabled audio device. If the radio is paired with other Bluetooth enabled audio device, its volume is independent from the APX radio. In this case, the volume is only adjustable on the device.
Adjust volume up/down on the Bluetooth audio device.
The radio display shows Volume XX, and you hear a short, medium-pitched tone.
Viewing and Clearing the Bluetooth Device Information
1
or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
2
or to Devices.
Once the display highlights the Devices, the display shows XX connected alternates with XX paired
.
3 Press the Menu Select button directly below Sel.
4 If there are devices being paired or connected, or along the list of <Device Friendly Name> to see the status of each device.
English
If there are no active Bluetooth devices being paired or connected, the display shows No devices
.
5 Perform one of the following actions:
• To clear the device from the list, or to the required device, press the Menu Select button directly below Clr.
• To exit from this function, press the Menu
Select button directly below Back to return to the previous screen without deleting the device name.
If Clr is selected, the display shows <Device
Friendly Name> clear?
.
6 Press the Menu Select button directly below Yes or No to proceed delete the device or to exit this function and return to previous screen..
If the device is deleted successfully, the display shows <Devlice Friendly Name> cleared to indicate clearing is successful.
If the device is not deleted successfully, you hear the radio sounds a short, low-pitched tone. The display
shows <Devlice Friendly Name> clear failed.
The display returns to previous screen.
Note: If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.)
Clearing All Bluetooth Devices Information
The following methods are options on how to clear all
Bluetooth devices information. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Clearing all Bluetooth devices information via the preprogrammed Bluetooth On/Off button: a) Long press the preprogrammed Bluetooth
On/Off button.
You hear a short, medium-pitched tone. The display shows Please wait to indicate clearing is in progress.
If successful, the display shows All BT devices cleared
.
If unsuccessful, you hear the radio sounds a short, low-pitched tone. The display shows
Clear all BT devices failed
. The display returns to Bluetooth feature screen.
• Clearing all Bluetooth devices information via the radio menu Clr: a) or to Devices and press the Menu
Select button directly below Clr.
You hear a short, medium-pitched tone. The display shows Clear all BT devices?.
b) Press the Menu Select button directly below
Yes
to proceed.
The display shows Please wait to indicate clearing is in progress.
If successful, the display shows All BT devices cleared
.
If unsuccessful, you hear the radio sounds a short, low-pitched tone. The display shows
Clear all BT devices failed
. The display returns to Bluetooth feature screen.
Note: If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all
155
English
156
previously paired devices as well. (Please see your accessories manual for further details.)
Editing the Bluetooth Friendly Name
Your radio must be preprogrammed to allow you to use this feature.
1
or to BT. Press the Menu Select button directly below BT to access the Bluetooth feature screen.
2
or to Friendly name and press the Menu
Select button directly below Edit.
A blinking cursor appears in the Friendly Name screen.
3 Use the keypad to edit the text.
4 Perform one of the following actions:
• Press the Menu Select button directly below
Ok
to save the new Friendly Name and return to the Bluetooth feature screen.
• Press the Menu Select button directly below
Cncl
to return to the Bluetooth feature screen.
Pairing with LEX 700
Ensure that Bluetooth feature of your radio is on and the Bluetooth tones are enabled.
1 Turn on the LEX 700 and activate the Bluetooth feature.
2 Place the LEX 700 close to the radio aligning the
Bluetooth Pairing Location on LEX 700 with the
Bluetooth Pairing Location on the radio.
If the pairing process is successful, you hear an incremental-pitched tone from the radio. The radio begins to connect to LEX 700. If the connecting process is successful, you hear an incrementalpitched tone. The display shows LEX 700 connected
, and the Bluetooth icon turns from to .
If unsuccessful, one of the following scenarios will occur:
• You hear a short, low-pitched tone and the display shows Bluetooth pairing failed (if pairing fails).
English
• You hear a decremental-pitched tone and the display shows LEX 700 unpaired (if the connection fails within 6 seconds).
• You hear a short, low-pitched tone and the display shows LEX 700 connect failed (if the radio has the pairing record of LEX 700 and the connection fails).
Repeat this step to re-initiate the pairing process.
Note: To unpair the LEX 700 after a successful
connection, follow the steps in
Clearing the Bluetooth Device Information
on page
154.
Programming Over Project 25 (POP 25)
(ASTRO 25 and ASTRO Conventional)
This feature enables configuration data to be upgraded to your radio over-the-air. This feature retains full use of the radio during the configuration data transfer without interrupting communication. The upgrade pauses to give priorities to voice call, and continues after the voice call ended.
Once a configuration upgrade is downloaded to your radio, you can install new changes immediately or delay changes to be installed on the radio when it is being powered up.
Your radio can also be configured to allow you to accept or reject an upgrade.
Note: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
Responding to the Notification of Upgrade
1 The display shows Upgrade?.
2 Perform one of the following actions:
• Press the Menu Select button below Acpt to accept the request to upgrade immediately.
• Press the Menu Select button below Dlay to delay the request to upgrade.
• Press the Menu Select button below Rej to reject the request to upgrade.
One of the following scenarios occurs:
• If you choose to accept, the display shows Upg Rx
In Prog
to indicate the upgrade received is in progress.
157
English
If the upgrade is successful, the display shows
Program done
.
If the upgrade fails, the display shows Program failed
. The radio remains in current configuration.
• If you choose to delay, the radio prompts to upgrade in the next power up of your radio.
• If you choose to reject, the display shows Upg
Aborted
. The radio continues to function with the current configuration until it gets reprogrammed.
Note: If your radio has problems upgrading over-theair, consult a qualified technician for details.
158
Voice Announcement
This feature enables the radio to audibly indicate the current feature mode, zone or channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display.
Each voice announcement is within a limit of three seconds maximum. The sum duration of all different voice announcements in a radio shall be no more than 1000 seconds.
English
Note: This feature must be preprogrammed by a qualified radio technician.
Check with your agent if Voice Announcement is available for the feature you need.
The two options of priority for the Voice
Announcement available are:
High Enables the voice of the feature to announce even when the radio is receiving calls.
Low Disables the voice of the feature from announcing when the radio is receiving calls.
You hear a voice announcement when the features below are preprogrammed in the radio.
• The radio powers up. The radio announces the current zone and channel it is transmitting.
• Press the preprogrammed voice announcement button (which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting.
Note: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority.
All the three programmable buttons at the side of the radio support this feature.
• Change to a new zone. The radio announces the current zone and channel it is transmitting.
• Change to a new channel remaining within the current zone. The radio announces the current channel.
• Press either the Menu Select button or preprogrammed button or switch of the radio to launch or terminate Scan, PL Disabled,
Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation.
Site Selectable Alerts (ASTRO 25)
A Site Selectable Alert (SSA) is an Intelligent Lighting indicator together with audio alert sent to radios at a site or a few sites to notify the users when there is a special situation that they need to be aware of. Only authorized radios are enabled to send SSA.
Upon the activation of a SSA, the receiving radios display the alert alias and generate the periodic alert tone.
Note: Alert alias, alert tone, and alert period can be preprogrammed. Alert period is the duration for the radio to repeat the alert tone. An interval of 5 seconds might impact the battery life of the radio. Check with your dealer or system administrator for more details.
When mixing SSA with received voice audio, the SSA alert is reduced in volume to ensure that the voice message is still heard clearly. Therefore, it is important that the SSA audio files are created with clear loud audio to ensure they can still be heard clearly when played at reduced levels.
Sending SSA Notification to Single Site
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Start Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to the desired Site Alias. Press the Menu
Select button directly below Sel.
The display shows the Select Alert screen.
159
English
5
or to select the desired Alert Alias and press the Menu Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
If the site is not available, the display shows <Site
Alias> not available
.
If the site does not exist, the display shows <Site
Alias> does not exist
.
6 To return to the Home screen, press the Menu
Select button directly below Exit.
160
If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the <Alert Alias> with the intelligent lighting at Home screen.
Sending SSA Notification to Single Site Via Manual
Entry
1
or to SSA.
English
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Start Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to [SiteID Entry] to send alert via manual entry. Press the Menu Select button directly below Edit.
The display shows the Enter SiteID screen.
5 Key in the desired Site ID and press the Menu
Select button directly below Ok.
If a correct Site ID is entered, the display shows the Select Alert screen.
If a wrong Site ID is entered, the display shows
Invalid ID
and prompts to enter the Site ID again.
6
or to select the desired Alert Alias and press the Menu Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
If the site is not available, the display shows <Site
ID> not available
.
If the site does not exist, the display shows <Site
ID>does not exist
.
7 To return to the Home screen, press the Menu
Select button directly below Exit.
If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the <Alert Alias> with the intelligent lighting at Home screen.
Sending SSA Notification to All Sites
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Start Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to [All Sites] and press the Menu
Select button directly below Sel.
The display shows the Select Alert screen.
5
or to select the desired Alert Alias and press the Menu Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
If one or more sites are not available, the display shows Not all sites available. Repeat
3
.
6 To return to the Home screen, press the Menu
Select button directly below Exit.
If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the <Alert Alias> with the intelligent lighting at Home screen.
161
English
162
Sending SSA Notification to All Available Sites
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Start Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to [All Avail] and press the Menu
Select button directly below Sel.
The display shows the Select Alert screen.
5
or to select the desired Alert Alias and press the Menu Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
6 To return to the Home screen, press the Menu
Select button directly below Exit.
If you are at the site designated to receive this alert, you can hear an alert tone repeated periodically. The display shows the <Alert Alias> with the intelligent lighting at Home screen.
Stopping SSA Notification of a Single Site
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Stop Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to select the desired Site Alias and press the Menu Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
If the site is not available, the display shows <Site
Alias> not available
.
English
If the site does not exist, the display shows <Site
Alias>does not exist
.
5 To return to the Home screen, press the Menu
Select button directly below Exit.
The SSA Alert for the designated site stops.
Stopping SSA Notification of a Single Site Via Manual
Entry
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Stop Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to [SiteID Entry] and press the Menu
Select button directly below Edit.
The display shows the Enter SiteID screen.
5 Key in the required Site ID and press the Menu
Select button directly below Send.
One of the following scenarios occur:
• If a wrong Site ID is entered, the display shows
Invalid ID
and prompts to enter the Site ID again.
• If a correct Site ID is entered, the display shows Sending req.
• If the request is successful, the display shows
Req successful
.
• If the single site is not available, the display shows <Site ID> not available.
• If the single site does not exist, the display shows <Site ID> does not exist.
6 To return to the Home screen, press the Menu
Select button directly below Exit.
The SSA Alert for the designated site stops.
Stopping SSA Notification of All Sites
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Stop Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
163
English
4
or to [All Sites] and press the Menu
Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
If one or more sites are not available, the display shows Not all sites available. Repeat step
.
5 To return to the Home screen, press the Menu
Select button directly below Exit.
164
The SSA Alert for all sites stop.
Stopping SSA Notification of All Available Sites
1
or to SSA.
2 Press the Menu Select button directly below SSA.
The display shows the Site Alert screen.
3
or to Stop Alert and press the Menu
Select button directly below Sel.
The display shows the Select Site screen.
4
or to [All Avail] and press the Menu
Select button directly below Send.
The display shows Sending req.
If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows
Req failed
.
If the request is successful, the display shows Req successful
.
5 To return to the Home screen, press the Menu
Select button directly below Exit.
The SSA Alert for all available sites stop.
Long Term Evolution (LTE)
Note: Applicable for APX7000L only.
The APX7000L enhances the current radio operation by providing the radio with faster information delivery over an LTE broadband network. Utilizing the LTE network additionally allows the radio to perform simultaneously LMR voice operation while sending and receiving data via the LTE network. LTE
English
eliminates the need for radios to be physically present at a service facility when reconfiguration is required.
Networks supported include the public safety broadband network (band 14) and Verizon’s commercial network (band 13).
This module allows the voice communication of P25 and data communication via LTE to take place simultaneously.
Caution: If the radio transmission personalities contain one 700MHz channel, the entire personality will not be able to use LTE.
The APX 7000L radio exterior has the main microphone and speaker grill bumped out.
Besides this, he remainder of the exterior is identical to APX 7000.
A
B
The table below describes the condition when the radio works in different operating systems with LTE.
System Operation Scenarios
IV&D LTE and IV&D are mutually exclusive.
Both systems cannot operate at the same time.
LMR
The radio is preprogramed to stop LTE operation when radio switched to a LMR
700MHz frequency.
When the radio is switched to operate in
700MHz LMR, LTE operation is turned off.
165
English
System Operation Scenarios
The radio can still operate on 700MHz
LMR where the LMR voice and data are available to the user.
LTE is operational again when the frequencies are switched back to either a
VHF or a 800 MHz LMR frequency.
166
The LTE feature can be preprogrammed to a programmable button for quick access to LTE screen or to activate LTE feature. The LTE button must be preprogrammed by a qualified technician before user can use it.
Data Profiles Available for LTE
There are three different profiles available for LTE data operation.
Broadband
Only
Trunking and
Broadband
Use only LTE data transmission network. In the absence of LTE coverage, the radio has no data functionality.
Use LTE data transmission network when available. When
Conventional and
Broadband
LTE is not available or turned off, the radio falls back to using IV&D
LMR data, if available. Once LTE coverage becomes available again, the radio reverts back to using LTE data transmission network.
Use LTE data transmission network when available. When
LTE is not available or turned off, the radio falls back to using
Conventional LMR data, if available. Once LTE coverage becomes available again, the radio reverts back to using LTE data transmission network.
Turning On the LTE at the LTE Menu Screen
1 Perform one of the following actions:
•
• Press the LTE button to enter the LTE screen.
or to LTE. Press the Menu Select button directly below LTE to enter the LTE screen.
If LTE modem is not ready or busy setting up, the display shows Please wait. Once the LTE
English
modem is ready, the display shows the LTE screen.
2 Perform one of the following actions:
• Press and hold the LTE button.
• Press the Menu Select button directly below
On
to enable LTE connection.
The screen prompts LTE on to indicate radio is initating the LTE connection. The Status shows
Connecting...
to indicate the radio is initating connection to LTE system.
The display shows LTE connected once the radio is connected. The Status shows Connected. The LTE icon appears at the top of the front display to indicate
LTE modem is connected.
If there is an encryption error, the display shows LTE service error
and the Status shows Service error
.
If there are no LTE networks available, the display shows No LTE service and the Status shows No service
until successfully connected to LTE or encounter service error.
Note: It is advisable to turn off the LTE if the radio prompts LTE service error or No LTE service.
For the error no LTE service available, turn on the
LTE after you moved to another site to check the availablity.
Turning On the LTE with LTE Button
Press and hold the preprogrammed LTE button.
The display shows LTE on to indicate radio is initating the LTE connection.
The display shows LTE connected once the radio is connected and the Status shows Connected. The
LTE icon appears at the top of the front display to indicate LTE modem is connected.
If there is an encryption error, the display shows LTE service error
.
if there are no LTE networks available, the display shows No LTE service.
Note: It is advisable to turn off the LTE if the radio prompts LTE service error or No LTE service.
For the error no LTE service available, turn on the
LTE after you moved to another site to check the availablity.
167
English
168
Turning Off the LTE Connection
To extend the radio battery life, disable the LTE
Connection when radio is out of LTE coverage.
The following methods are options on how to turn off the LTE Connection. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turning Off the LTE Connection via preprogrammed LTE button: a) Press the preprogrammed LTE button to enter
LTE
screen.
b) Press and hold the preprogrammed LTE button.
The display shows LTE Off and the Status shows
Off
and the LTE icon disappears to indicate the
LTE connection is off.
• Turning Off the LTE Connection via LTE radio menu: a) or to LTE and press the Menu Select button directly below LTE to access the LTE screen.
b) Press the Menu Select button directly below
Off
to disable LTE connection.
The display shows LTE Off and the Status shows Off and the LTE icon disappears to indicate the LTE connection is off.
c) Press the Menu Select button below Exit to return to Home screen.
Information at the LTE Screen
Here are the definitions of the statuses appeared below the Status, Network and Signal Strength shown on the LTE screen.
• The definitions of different statuses shown below the Status of LTE screen:
Connecting
Connected
Disconnected
Disabled
The radio is trying to connect to an LTE modem.
LTE communication is currently on.
LTE communication is currently disconnected.
LTE communication is currently disabled on the selected channel.
English
Off
LTE communication of the radio is currently off.
No Service
No LTE service detected at the current site.
Service Error
[3]
There is an LTE service error.
LTE HW error
[3]
There is an LTE hardware error.
VPN auth error
[3]
Incorrect key installed for
VPN.
Service fatal error
[4]
LTE function has come to a stall.
• The definitions of different statuses shown below the Network of LTE screen:
<Network name> The currently connected LTE
Unavailable
network name.
No LTE network connected currently.
• The definitions of different statuses shown below the Signal Strength of LTE screen:
Please wait
Unavailable
Rating of the signal strength
The radio is trying to connect to an LTE modem.
The radio does not have an
LTE connection currently.
You see one of the following rating when LTE is connected:
Excellent > Good > Fair >
Poor
Scenario of Changing from LTE-enabled Channel to
LTE-disabled Channel
When entering a non-LTE channel the status field in the LTE screen shows Disabled. Press or press and hold of the LTE button prompts short, low-pitched tone.
3
4
Bring the radio to the qualified technician to check the issue if the error persists.
You can try to power on your radio again to reinitiate the LTE function. If this error persists, bring your radio to the qualified technician to verify the issue.
169
English
170
If the display is showing LTE screen when entering the LTE-disabled channel, the display returns to
Home screen immediately.
Scenario of Changing from LTE-enabled Channel to
Unprogrammed Channel
When entering a unprogrammed channel the display prompts Unprogrammed and the LTE menu dissapears. Pressing the LTE button prompts short, low-pitched tone.
If the display is showing LTE screen when entering the unprogrammed channel, the display returns to
Home screen immediately and you are unable to see nor access the LTE screen.
Scenario of Entering or Exiting Out-of-Range Site
When the radio moves beyond the LTE network coverage, which means out-of-range, the radio prompts No LTE service. The LTE screen is
on page 168 for the status shown at the LTE screen.
With the LTE of the radio turned on, when the radio moves back to LTE connected site, the radio prompts
LTE connected
.
Utilities
Viewing Recent Calls
This feature allows you to view the recent incoming and outgoing call information of the following call types:
• Call Alert
• Selective Call
• Private Call
• Phone Call (Outgoing Only)
• Emergency Call (Incoming Only)
Note: The radio can also be preprogrammed to log only the radio IDs associated with incoming Dispatch
Calls. Check with your dealer or system administrator for more information.
The following methods are options on how to view recent calls. The result of all the methods is the same.
You can use the options interchangeably depending on your preference and the programmed functions.
• Viewing recent calls via the preprogrammed
Recent Calls button: a) Press the preprogrammed Recent Calls button.
English
b) or to scroll through the list.
c) To return to the Home screen, press the Menu
Select button directly below Exit, press or the PTT button.
• Viewing recent calls via the radio menu: a) or to Rcnt.
b) Press the Menu Select button directly below
Rcnt
to access the Recent Calls feature screen.
c) or to scroll through the list.
d) To return to the Home screen, press the Menu
Select button directly below Exit, or the
PTT button.
The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu Inactive
Exit Tone upon feature exit.
Using the Flip Display
This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still in the carry holder attached to your belt.
To flip the display, press and hold the preprogrammed Light/Flip button
Selecting a Basic Zone Bank
The Basic Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Basic Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature.
This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions.
Use the preprogrammed Basic Zone Bank button to toggle the position between Bank 1 and Bank 2.
The top display shows the status icons (A, B, C, D,
E
or F) or the zone name based on the bank and switch position selected.
icons for more information on the status icons.
Selecting an Enhanced Zone Bank
This feature is created in order to allow users to communicate in more zones. An Enhanced Zone
171
English
Bank (EZB) consists of three zones. This also means each icon A, B, C, ... or Y consist of three zones. You can use the preprogrammed 3-position A-B-C switch to select the first, second or third zone in an EZB.
This feature allows user to navigate from up to 75 zones in 25 EZBs.
Note: The Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Enhanced Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature.
1 Press the preprogrammed EZB Up or EZB Down button to scroll the EZB up or down or press and hold the preprogrammed EZB Up or EZB Down button to fast scroll the EZB up or down.
2 Turn the 3-Position A/B/C Switch to select the first, second or third zone in the selected EZB.
172
Selecting the Power Level
Note: This feature must be preprogrammed by a qualified radio technician.
This feature enables you to reduce the transmit power level for specific case that requires a lower
English power level. You can select the power level at which your radio transmits. The radio always turns on to the default setting. These reduced transmit power level settings do not affect the receiving performance of your radio, nor diminish the overall quality of the audio and data functionality of the radio given the following conditions.
Power level Low enables a shorter transmitting distance and to conserve power. Power level High enables a longer transmitting distance.
The following methods are options on how to select the power level. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Selecting the Power Level via the Transmit
Power Level switch: a) Use the preprogrammed Transmit Power
Level switch to toggle the power level between low and high power.
• Selecting the Power Level via the radio menu: a) or to Pwr.
b) Press the Menu Select button directly below
Pwr
.
The display shows Low power and the low power icon or the display shows High power and the high power icon.
Selecting a Radio Profile
This feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile.
Please refer to a qualified technician for more information.
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You will hear the Menu
Inactive Exit Tone upon feature exit.
The following methods are options on how to select a radio profile. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Selecting a radio profile via the preprogrammed
Profile button: a) Press the preprogrammed Profile button.
b) or to scroll through the menu selections.
c) Press the Menu Select button directly below
Sel
to select the required radio profile, or press the Menu Select button directly below Exit to exit the screen without making any changes.
The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.
• Selecting a radio profile via the radio menu: a) or to Prfl and press the Menu Select button directly below Prfl to access the
Profiles
feature screen.
b) or to scroll through the menu selections.
c) Press the Menu Select button directly below
Sel
to select the required radio profile, or press the Menu Select button directly below Exit to exit the screen without making any changes.
The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.
173
English
Enabling and Disabling the Radio Alias
This feature allows you to display or hide the radio alias (name).
Press the Menu Select button directly below
MyID
.
The display shows momentary Radio ID off, and the radio alias disappears from the Home screen or the display shows momentary Radio ID on, and the radio alias appears on the Home screen.
Selecting the Audio Speaker
Your radio must be preprogrammed to allow you to use this feature.
This feature allows you to select the speaker route for the radio's audio from either the main or the secondary speaker using the radio profile settings.
While both speakers function together with the secondary speaker enhancing intelligibility of the received audio during typical radio operation, each speaker has an independently-tuned frequency response and volume level operation.
174
English
The secondary speaker also has a "whisper" mode with a modified volume taper for quieter modes of operation.
Note: If an external speaker or microphone accessory is attached to the radio, neither internal speaker is operational as audio is routed to the accessory.
The following methods are options on how to select the audio speaker. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Select the audio speaker via the preprogrammed
Profile button: a) Press the preprogrammed Profile button.
b) or to scroll through the menu selections.
c) Press the Menu Select button directly below
Sel
to select the radio profile with the required speaker routing or press the Menu Select button directly below Exit to exit the screen without making any changes.
The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.
• Select the audio speaker via the radio menu Prfl: a) or to Prfl.
b) To access the Profiles feature screen, press the Menu Select button directly below Prfl.
c) or to scroll through the menu selections.
d) Press the Menu Select button directly below
Sel
to select the radio profile with the required speaker routing or press the Menu Select button directly below Exit to exit the screen without making any changes.
The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile.
Controlling the Display Backlight
You can enable or disable the radio’s display backlight as needed, if poor light conditions make the display or keypad difficult to read.
Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radio's front display.
Note: The backlight setting also affects the Menu
Select buttons, the Navigation button and the
keypad backlighting accordingly.
The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level.
Perform one of the following actions:
• To toggle the backlight on or off, press the preprogrammed Light/Flip button.
• To turn the backlight on, press any key of the
keypad, the Menu Select or Navigation button, or any programmable radio controls or buttons.
Locking and Unlocking the Keypad and Controls
You can lock the keypad, programmable buttons, rotary knobs and switches of your radio to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suit your usage.
1 Toggle the preprogrammed Keypad/Control Lock button or switch to on.
2 The display shows Kypd/Ctrl Lock.
3 To unlock the keypad, knobs and buttons, toggle again.
175
English
Turning the Controls and Keypad Buttons Tones On or
Off
You can enable and disable the tones of Navigation buttons, controls and keypad if needed.
• Turning the tones on or off via the preprogrammed
Mute button: a) To turn the tones off or on, press the preprogrammed Mute button.
• Turning the tones on or off via the radio menu: a) or to Mute.
b) Press the Menu Select button directly below
Mute
.
The display shows momentary Tones off, indicating that the tones are disabled or the display shows momentary Tones on, and you hear a short tone indicating that the tones are enabled.
176
Turning Voice Mute On or Off
You can enable and disable voice transmission, if needed.
The following methods are options on how to turn
Voice Mute on or off. The result of all the methods is the same. You can use the options interchangeably depending on your preference and the programmed functions.
• Turning Voice Mute on or off via the preprogrammed Voice Mute button: a) To turn the feature off or on, press the preprogrammed Voice Mute button.
• Turning Voice Mute on or off via the radio menu: a) or to VMut.
b) Press the Menu Select button directly below
VMut
.
The display shows momentary Voice mute off, and you hear a short tone, indicating that the feature is disabled or the display shows momentary Voice mute on
, and you hear a short tone, indicating that the feature is enabled.
Using the Time-Out Timer
This feature turns off your radio’s transmitter. You cannot transmit longer than the preset timer setting.
If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone.
English
The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician.
Note: You hear a brief, low-pitched, warning tone four seconds before the transmission times out.
1 Hold down the PTT button longer than the preprogrammed time.
You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the PTT button.
2 Release the PTT button.
The timer resets.
3 To re-transmit, press the PTT button.
The time-out timer restarts and the LED lights up solid red.
Time and Date Setup
You can set the time and date for your radio.
Settings:
• The default time setting is a 12-hour clock. The display shows 12:00AM.
• The AM/PM selection is not available for the 24hour clock setting.
• The default setting for the domestic date shows
MDY
.
Note: Check with your dealer or system administrator for additional programmable settings for this feature.
Editing the Time and Date
1
or to Clck.
2 Press the Menu Select button directly below
Clck
.
The display shows the current setting of the radio.
3 Press the Menu Select button directly below
Edit
.
The first item blinks.
4 Perform one of the following actions:
•
• or to change the selected item.
or one or more times to move to an item you wish to change. or to change the selected item.
177
English
• Press the Menu Select button directly below
Exit
to exit the screen without making any changes and return to the Home screen.
5 Perform one of the following actions:
• Press the Menu Select button directly below
Ok
once you have finished to save your changes and return to the Home screen.
• Press the Menu Select button directly below
Cncl
to discard all changes and return to the
Home screen.
Press at any time to return to the Home screen without saving your changes.
Note: If a call arrives while the radio is in the clock-setting menu, the radio exits clock setting and displays the call information. Any changes made before the call is not saved.
Using Conventional Squelch Operation Features
This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise.
178
English
Analog Options
Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available
(preprogrammed) per channel.
Mode
Carrier squelch (C)
PL or DPL
Result
You hear all traffic on a channel.
The radio responds only to your messages.
Digital Options
One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information.
Option
Digital Carrier-Operated
Squelch (COS)
Normal Squelch
Result
You hear any digital traffic.
You hear any digital traffic having the correct network access code.
Option
Selective Switch
Result
You hear any digital traffic having the correct network access code and correct talkgroup.
Using the PL Defeat Feature
This feature allows you to override any coded squelch
(DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel.
Place the preprogrammed PL Defeat switch in the
PL Defeat position.
One of the following scenarios occurs:
• You hear any activity on the channel.
• The radio is muted if no activity is present.
Note: When this feature is active, the Carrier
Squelch status indicator is displayed.
Digital PTT ID Support
This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher.
Your radio’s ID number is also automatically sent every time the PTT button is pressed. This is a perchannel feature. For digital voice transmissions, your radio’s ID is sent continuously during the voice message.
Smart PTT Feature (Conventional Only)
Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations.
When smart PTT is enabled in your radio, you cannot transmit on an active channel.
If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy.
The following table shows the variations of smart
PTT:
179
English
Mode
Transmit Inhibit on Busy
Channel with
Carrier
Transmit Inhibit on Busy
Channel with
Wrong Squelch
Code
Quick-Key
Override
Description
You cannot transmit if any traffic is detected on the channel.
You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented.
This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit.
180
Transmit Inhibit
This feature is available for APCO 25 trunking, Type II trunking and Conventional operations for all APX radios.
English
When Transmit Inhibit feature is enabled, the radio stops all transmission including voice and data. The radio could receive messages but not replying the acknowledgement request of the received message.
User could physically control the transmission of the radio especially during operation in hazardous environments with this feature. An environment is considered hazardous when the power emitted by the radio power amplifier could initiate an explosion or other dangerous reactions.
When the Transmit Inhibit feature is disabled, the radio functions according to its normal operations.
The radio sounds alert tone when user enters or exits this feature and also when PTT is pressed.
Note: Acknowledgement of any messages required from the radio is not transmitted if the Transmit
Inhibition is enabled.
Enabling Transmit Inhibition
Perform one of the following actions:
• Switch the preprogrammed Transmit Inhibit switch to Transmit Inhibit enabled.
•
or to TxIn. Press the Menu Select button below TxIn.
• Press the Transmit Inhibit programmable button.
Note: If the user has disabled TX Inhibit via the menu and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value.
The display shows Tx inhibit on. You hear a sequence of short, low
‐high tones to indicate transmission is inhibited.
Pressing PTT triggers the radio sounds a constant short, low
‐pitched tone (reject tone).
Note: The status of the Transmit Inhibit does not change after the radio powers up.
Disabling Transmit Inhibition
Perform one of the following actions:
•
• Switch the preprogrammed Transmit Inhibit switch to Transmit Inhibit disabled position.
or to TxIn. Press the Menu Select button below TxIn.
• Press the Transmit Inhibit programmable button.
Note: If the user has disabled TX Inhibit via the softkey and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value.
The display shows Tx inhibit off. You hear a sequence of short, high
‐low tone (Transmit Inhibit
Off tone) to indicate transmission is back to normal operation.
IMPRES Battery Annunciator
This feature displays the current capacity and charges cycles of your battery when an IMPRES
™
Battery is powering your radio. This feature must be enabled in your radio to see the information.
The information shown are:
Rated Capacity
Percentage of current battery capacity.
Remaining
Capacity
Remaining power of the battery in mAh.
Estimated
Charges
Number of charges cycles the battery has gone through.
181
English
Accessing the Battery Info screen
1
or to Batt.
2 Press the Menu Select button directly below
Batt
.
The display shows the details of the battery.
3 To return to the Home screen, press the Menu
Select button directly below Exit.
182
General Radio Information
Your radio contains information on the following:
• Radio Information
• IP Display
• Control Assignments
• Soft ID (If enabled)
Note: The radio automatically exits the feature, if the feature inactivity timer is enabled, when the radio is left idle and the timer expires. You hear the Menu
Inactive Exit Tone upon feature exit.
Accessing the Radio Information
This feature displays the following radio information:
• Host Version
English
• Secure Version
• Model Number
• ESN
• Flash Code
• Tuning Version
• Option Board Type (optional)
• Option Board Bluetooth Address (optional)
• Expansion Board Type (optional)
• DSP Version
• KG (Secure Algorithm)
• Serial Number
• Flash Size & Type
• RF Band
• Processor Version
• Option Board Serial Number (optional)
• Option Board Software Version (optional)
• Language Pack ID and Version (only when the language of the display is set to non-English)
• IMSI (APX 7000L only)
• IMEI (APX 7000L only)
• ICCID (APX 7000L only)
Note: To return to the Home screen, press at any time.
1 Perform one of the following actions:
•
• Press the preprogrammed Info button.
or to Info and press the Menu Select button directly below Info.
2
or to Radio Info and press the Menu
Select button directly below Sel.
The display shows the Information screen.
3 Perform one of the following actions:
• or to scroll through the various information.
• To return to the previous screen, press the
Menu Select button directly below Back.
• To return to the Home screen, press .
Viewing the IP Information
This feature displays the device name, IP address, and status of your radio.
Note: The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information.
APX 7000L radio has different list of information as shown in the following list.
• iosu
• iosc
• LOOPBACK
• Ite1
• vpn1
• device name
1 Perform one of the following actions:
•
• Press the preprogrammed Info button.
or to Info and press the Menu Select button directly below Info.
2
or to IP Info and press the Menu Select button directly below Sel.
The display shows the IP Info screen.
3 Perform one of the following actions:
• or to scroll through the various information.
• Press the Menu Select button directly below
Back
to return to the previous screen.
• Press to return to the Home screen.
183
English
184
English
Viewing the Control Assignments
This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel.
on page 31 for more information on the various programmable features of your radio.
1 Perform one of the following actions:
•
• Press the preprogrammed Info button.
or to Info and press the Menu Select button directly below Info.
2
or to Control map and press the Menu
Select button directly below Sel.
The display shows the Control Map screen.
3 Perform one of the following actions:
• or to scroll through the various information.
• Press the Menu Select button directly below
Back
to return to the previous screen.
• Press to return to the Home screen.
Editing the Soft ID
Your radio must be preprogrammed to allow you to use this feature.
This feature allows you to change your username.
1 Perform one of the following actions:
•
• Press the preprogrammed Info button.
or to Info and press the Menu Select button directly below Info.
2
or to Soft ID and press the Menu Select button directly below Sel.
The display shows the current Soft ID.
3 Perform one of the following actions:
• Press the Menu Select button directly below
Edit
to edit the current Soft ID.
• Press the Menu Select button directly below
Back
to return to the previous screen.
A blinking cursor appears in the Edit Soft ID screen.
4 Use the keypad to edit the text.
5 Perform one of the following actions:
• Press the Menu Select button directly below
Ok
to save the new Soft ID and return to the previous screen.
• Press the Menu Select button directly below
Cncl
to return to the previous screen.
185
English
Helpful Tips
Radio Care
Caution:
• Your radio casting has a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers.This could create leak paths into the radio and the radio’s submergibility will be lost.
A
• (For APX 7000/APX 7000L R Radios Only)
Your radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours.
Exceeding either maximum limit may result in damage to the radio.
• (For APX 7000/APX 7000L R Radios Only)
Elastomer technology materials used for seals in rugged portable radios can age with time and environmental exposure.
Therefore, Motorola recommends that rugged radios be checked annually as a preventive measure in order to assure the watertight integrity of the radio. Motorola details the disassembly, test, and reassembly procedures along with necessary test equipment needed to inspect, maintain and troubleshoot radio seals in the radio’s service manual.
• If the radio battery contact area has been submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio.
• If the radio has been submerged in water, shake the radio well so that any water that
186
English
may be trapped inside the speaker grille and microphone port can be removed.
Otherwise, the water will decrease the audio quality of the radio.
• Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician.
Cleaning Your Radio
Caution: Do not use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures.
Do not submerge the radio in the detergent solution.
To clean the external surfaces of your radio, follow the procedure described next.
1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution).
2 Apply the solution sparingly with a stiff, nonmetallic, shortbristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth.
3 Clean battery contacts with a lint-free cloth to remove dirt or grease.
Proper Ways to Handle the Radio
• Do not pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna.
• Avoid subjecting the radio to an excess of liquids.
Do not submerge the radio unless it is a ruggedized.(APX 7000/APX 7000L R model)
• Avoid subjecting the radio to corrosives, solvents or chemicals.
• Do not disassemble the radio.
• Keep the accessory-connector cover in place until ready to use the connector. Replace the cover immediately once the accessory has been disconnected.
• When charging the radio using a wall mounted charger, the radio must be turned off. Otherwise, the Man Down Alert and Emergency may be accidentally triggered.
187
English
188
Radio Service and Repair
Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer.
Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for an additional period of either one or two years beyond the normal expiration date of the standard warranty. For more information about ESP, contact the Motorola Radio Support Center at 3761
South Central Avenue, Rockford, IL 61102 (800)
227-6772 / (847)725-4200.
Battery Care
Battery Charge Status
Your radio can indicate the battery’s charge status through:
• the LED and sounds.
• the fuel gauge icon on the display.
You can also check the battery charge status via the menu entry. See
on page 181 for more information.
LED and Sounds
When your battery is low:
• the LED blinks red when the PTT button is pressed.
• you hear a low-battery “chirp” (short, high-pitched tone).
Fuel Gauge Icons
A blinking fuel gauge icon ( ) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one.
English
Gauge Battery Charge
76% to 100% full
[5]
Top Display:
51% to 75%
[5]
Top Display:
26% to 50%
[5]
Top Display:
5
These are for IMPRES
™
battery operation only.
Gauge Battery Charge
11% to 25%
[5]
Top Display:
Top Display:
10% or less (at 10%, the gauge begins blinking)
189
English
Battery Recycling and Disposal
In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for battery collection and recycling. Many retailers and dealers participate in this program.
For the of the drop-off facility closest to you, access
RBRC's Internet web site at
www.rbrc.com
or call
1-800-8-BATTERY. This internet site and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies.
190
English
Accessories
The accessory link below is for APX radios. Not all accessories are FCC certified to operate with all APX models and/or bandsplits. Please refer to the specific
APX radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility.
http://www.motorolasolutions.com/APX
Note: GPS only antenna is only used in either a single band UHF or 700/800 application where the
Public Safety Microphone (PSM) is used with the corresponding PSM antenna. This antenna is only for
GPS reception and cannot be used for receive/ transmit operation at UHF, VHF or 700/800. This antenna is never to be used on the PSM.
191
English
Maritime Radio Use in the VHF
Frequency Range
Special Channel Assignments
192
Emergency Channel
If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the
United States Coast Guard. Transmit the following information, in this order:
1 “MAYDAY, MAYDAY, MAYDAY.”
2 “THIS IS _____________________, CALL SIGN
__________.” State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times.
3 Repeat “MAYDAY” and the name of the vessel.
4 “WE ARE LOCATED AT
_______________________.” State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:
• latitude and longitude
• bearing (state whether you are using true or magnetic north)
• distance to a well-known landmark
• vessel course, speed or destination
5 State the nature of the distress.
6 Specify what kind of assistance you need.
7 State the number of persons on board and the number needing medical attention, if any.
8 Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc.
9 “OVER.”
10 Wait for a response.
11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you.
Non-Commercial Call Channel
For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9.
Operating Frequency Requirements
A radio designated for shipboard use must comply with Federal Communications Commission Rule Part
80 as follows:
English
• on ships subject to Part II of Title III of the
Communications Act, the radio must be capable of operating on the 156.800 MHz frequency.
• on ships subject to the Safety Convention, the radio must be capable of operating:
• in the simplex mode on the ship station transmitting frequencies specified in the
156.025 – 157.425 MHz frequency band, and
• in the semiduplex mode on the two frequency channels specified in the table below.
Note:
Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.
Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast
Guard.
Table 1: VHF Marine Channel List
Channel
Number
Frequency (MHz)
Transmit Receive
11
12
13**
14
15**
16
17**
7
8
9
10
*
4
1
2
5
6
156.550
156.600
156.650
156.700
156.750
156.800
156.850
156.050
156.100
156.150
156.200
156.250
156.300
156.350
156.400
156.450
156.500
156.550
156.600
156.650
156.700
156.750
156.800
156.850
160.
650
160.700
160.750
160.800
160.850
–
160.950
–
156.450
156.500
193
English
194
English
63
*
65
28
60
*
62
24
25
26
27
18
19
20
*
22
*
157.400
156.025
156.075
156.125
156.175
156.225
156.275
156.900
156.950
157.000
157.050
157.100
157.150
157.200
157.250
157.300
157.350
162.000
160.625
160.675
160.725
160.775
160.825
160.875
161.500
161.550
161.600
161.650
161.700
161.750
161.800
161.850
161.9
00
161.950
*
*
*
77**
78
79
80
73
74
75
76
66
67**
68
69
71
72
156.325
156.375
156.425
156.475
156.575
156.625
156.675
156.725
***
***
156.875
156.925
156.975
157.025
157.0
75
157.125
157.175
–
161.525
161.575
161.025
161.675
161.725
161.775
160.925
156.375
156.425
156.475
156.575
–
156.675
156.725
***
***
84
85
86
87
88
157.225
157.275
157.325
157.375
157.425
161.825
161.875
161.925
161.975
162.025
Note:
* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83
cannot be lawfully used by the general public in US waters.
** Low power (1 W) only.
*** Guard band.
Note: A – in the Receive column indicates that the channel is transmit only.
Declaration of Compliance for the Use of
Distress and Safety Frequencies
The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3.
Technical Parameters for Interfacing External
Data Sources
Input
Voltage
(Volts
Peak-topeak)
RS232
18V
Max Data
Rate
28 kb/s
Impedance
5k ohm
USB
3.6V
12 Mb/s
90 ohm
SB9600
5V
9.6 kb/s
120 ohm
195
English
196
Glossary
This glossary is a list of specialized terms used in this manual.
ACK
Acknowledgment of communication.
Active Channel
A channel that has traffic on it.
Analog Signal
An RF signal that has a continuous nature rather than a pulsed or discrete nature.
ARS
ASTRO 25
ASTRO
Conventional
Autoscan
Bluetooth
Automatic Registration Service
Motorola standard for wireless digital trunked communications.
Motorola standard for wireless digital conventional communications.
A feature that allows the radio to automatically scan the members of a scan list.
Bluetooth is an open wireless technology standard for exchanging data over short
English distances from fixed and mobile devices with high levels of security.
Bluetooth Pairing Bluetooth pairing occurs when two bluetooth devices exchanged a passkey to form a paired Bluetooth wireless connection.
Call Alert
Privately page an individual by sending an audible tone.
Carrier Squelch
Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver’s audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to “noise”.
Central
Controller
A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the
Channel
operations of the trunked repeaters.
A group of characteristics such as transmit/ receive frequency pairs, radio parameters, and encryption encoding.
Control Channel
In a trunking system, one of the channels that is used to provide a continuous, twoway/ data communications path between the central controller and all radios on the system.
Conventional
Conventional
Scan List
Typically refers to radio-to-radio communications, sometimes through a repeater (see
Trunking).
A scan list that includes only conventional channels.
COTS
CP
Cursor
Commercial Off-The-Shelf
Codeplug
A visual tracking marker (a blinking line) that indicates a on the display.
Deadlock
Digital Private
Line (DPL)
Digital Signal
Dispatcher
DSP
Dynamic
Regrouping
DSR
EID
Displayed by the radio after three failed attempts to unlock the radio. The radio must be powered off and on prior to another attempt.
A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone.
An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature.
An individual who has radio system management duties.
Digital Signal Processing
A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other.
Dynamic System Resilience
Encrypted Integrated Data
197
English
ICCID
IMEI
IMSI
198
English
Iosu
ESN
Failsoft
FCC
FM
Hang Up
Home screen
Electrical Serial Number
A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft.
Federal Communications
Commission.
Frequency Modulation
Disconnect.
The first display information after the radio completes its self test.
Integrate Circuit Card Identity
International Mobile Equipment
Identifier
International Mobile Subscriber
Identity
Inter-OS User for user IP traffic
iosc
Ite1
IV&D
KVL
LCD
LED
Li-Ion
LTE
Man Down
Inter-OS Control for control IP traffic
Adapter name used by the radio for LTE traffic
Integrated Voice and Data
Key-variable loader: A device for loading encryption keys into the radio.
Liquid crystal display.
Light-emitting diode.
Lithium ion.
Long Term Evolution
(telecommunication). LTE is a standard for wireless communication of high-speed data for mobile phones and data terminals.
A life-saving feature that senses the radio user may be in trouble by monitoring the whether the radio is in a vertical or horizontal position or whether
MCW
MDC
Menu Entry
Monitor
the radio is motionless. When this feature is triggered, the radio alerts the user with audio and visual alerts. It can also trigger Emergency Alarm the
Post-Alert Timer is not cancelled.
Mission Critical Wireless
Motorola Data Communication
A software-activated feature shown at the bottom of the display – selection of these features is controlled by the
, , and buttons.
Check channel activity by pressing the Monitor button. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio “opens the squelch” when the monitor button is pressed.
Multi-System
Talkgroup Scan
List
Network Access
Code
NiMH
Non-Tactical/
Revert
OCW
OTAR
Page
Personality
PIN
A scan list that can include both talkgroups (trunked) and channels (conventional).
Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites.
Nickel-metal-hydride.
The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel.
Operation Critical Wireless
Over-the-air rekeying.
A one-way alert, with audio and/or display messages.
A set of unique features specific to a radio.
Personal Identification Number
199
English
200
English
PremierOne
A software application which streamlines critical real time operations and simplifies system administration to deliver accurate, consistent and integrated information remotely to the requestors.
Preprogrammed
Refers to a software feature that has been activated by a qualified radio technician.
Private
(Conversation)
Call
A feature that lets you have a private conversation with another radio user in the talkgroup.
Private Line (PL)
A sub-audible tone that is transmitted such that only receivers decoding the tone receives it.
Programmable
Refers to a radio control that can have a radio feature assigned to it.
PTT
Push-To-Talk. The PTT button engages the transmitter and
Radio Frequency
(RF)
puts the radio in transmit (send) operation when pressed.
The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to
10,000,000 MHz).
Repeater
Selective Call
A conventional radio feature, where you talk through a receive/transmit facility that retransmits received signals, in order to improve communications range and coverage.
A feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you.
Selective Switch
Any digital P25 traffic having the correct Network Access
Code and the correct talkgroup.
Squelch
SSI
Standby
Status Calls
Tactical/ Non-
Revert
Talkaround
Talkgroup
Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker.
Synchronous Serial Interface
An operating condition whereby the radio’s speaker is muted but still continues to receive data.
Pre-defined text messages that allow the user to send a conditional message without talking.
The user talks on the channel that was selected before the radio entered the emergency state.
Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications.
An organization or group of radio users who communicate with each other using the same communication path.
Text Messaging Service
TMS
Trunking
Trunking Priority
Monitor Scan List
USK
UTC
The automatic sharing of communications paths between a large number of users (see
Conventional).
A scan list that includes talkgroups that are all from the same trunking system.
Unique Shadow Key.
Coordinated Universal Time.
The international time standard
(formerly Greenwich Mean
Time, or GMT). Zero hours UTC is midnight in Greenwich,
England, which is located at 0 degrees longitude. Everything east of Greenwich (up to 180 degrees) is later in time; everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other.
201
English
202
English
vpn1
Zone
Abbreviated as UTC (English backronym = Universal Time,
Coordinated), it is also known as Zulu (Z) Time.
Adapter name used by the radio for encrypted LTE traffic
A grouping of channels.
Limited Warranty
MOTOROLA COMMUNICATION PRODUCTS
I. WHAT THIS WARRANTY COVERS AND FOR
HOW LONG:
MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the MOTOROLA manufactured
Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
ASTRO APX 7000/APX
7000L Portable Units
Product Accessories
One (1) Year
One (1) Year
For LACR region:
ASTRO APX 7000/APX
7000L Portable Units
Product Accessories
Three (3) Years
One (1) Year
MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of
Product shall become the property of MOTOROLA.
This express limited warranty is extended by
MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA.
Unless made in a separate agreement between
MOTOROLA and the original end user purchaser,
MOTOROLA does not warrant the installation, maintenance or service of the Product.
MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the
Product, or for operation of the Product with any
203
English
ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique,
MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty.
204
II. GENERAL PROVISIONS:
This warranty sets forth the full extent of
MOTOROLA'S responsibilities regarding the Product.
Repair, replacement or refund of the purchase price, at MOTOROLA’s option, is the exclusive remedy.
THIS WARRANTY IS GIVEN IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. IMPLIED
WARRANTIES, INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY. IN NO EVENT SHALL
MOTOROLA BE LIABLE FOR DAMAGES IN
EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL LOSS,
LOST PROFITS OR SAVINGS OR OTHER
INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE SUCH PRODUCT, TO THE
FULL EXTENT SUCH MAY BE DISCLAIMED BY
LAW.
III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LIMITATION ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION OR EXCLUSIONS MAY
NOT APPLY.
This warranty gives specific legal rights, and there may be other rights which may vary from state to state.
IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location.
Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication
English
service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at
1-800-927-2744 US/Canada.
V. WHAT THIS WARRANTY DOES NOT
COVER:
1 Defects or damage resulting from use of the
Product in other than its normal and customary manner.
2 Defects or damage from misuse, accident, water, or neglect.
3 Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.
4 Breakage or damage to antennas unless caused directly by defects in material workmanship.
5 A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim.
6 Product which has had the serial number removed or made illegible.
7 Rechargeable batteries if:
• any of the seals on the battery enclosure of cells are broken or show evidence of tampering.
• the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.
8 Freight costs to the repair depot.
9 A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with
MOTOROLA’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from
MOTOROLA.
10 Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the
Product.
11 Normal and customary wear and tear.
VI. PATENT AND SOFTWARE PROVISIONS:
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent
205
English
206
English that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
1 that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim,
2 that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise, and
3 should the Product or parts become, or in
MOTOROLA’s opinion be likely to become, the subject of a claim of infringement of a United
States patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product.
The foregoing states the entire liability of
MOTOROLA with respect to infringement of patents by the Product or any parts thereof.
Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under
MOTOROLA patent rights or copyrights.
VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of
Illinois, U.S.A.
207
English
APX7000_DD_BackCover_HalfLetter_P299C.fm Page 1 Monday, November 3, 2014 5:27 PM
APX7000_DD_BackCover_HalfLetter_P299C.fm Page 2 Monday, November 3, 2014 5:27 PM
Motorola Solutions, Inc.
1303 East Algonquin Road
Schaumburg, Illinois 60196 U.S.A.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners.
© 2009–2014 Motorola Solutions, Inc. All rights reserved.
November 2014.
*6875945M01*
6875945M01- NA
advertisement
Related manuals
advertisement
Table of contents
- 5 Contents
- 13 Declaration of Conformity
- 17 Important Safety Information
- 18 Software Version
- 18 Notice to Users (FCC and Industry Canada)
- 19 Consignes de sécurité importantes
- 20 Version logicielle
- 20 Avis aux utilisateurs (FCC et Industrie Canada)
- 21 Computer Software Copyrights
- 22 Documentation Copyrights
- 23 Disclaimer
- 24 Getting Started
- 24 How to Use This Guide
- 24 Notations Used in This Manual
- 24 Additional Performance Enhancement
- 24 ASTRO 25 Enhanced Data
- 25 Dynamic System Resilience (DSR)
- 25 CrossTalk Prevention
- 25 Encrypted Integrated Data (EID)
- 25 SecureNet
- 25 Conventional Talkgroup and Radio Scan Enhancements
- 26 What Your Dealer/System Administrator Can Tell You
- 27 Preparing Your Radio for Use
- 27 Charging the Battery
- 27 Attaching the Battery
- 28 Attaching the Antenna
- 29 Removing and Attaching the Accessory Connector Cover
- 30 Using the Carry Holder
- 32 Turning On the Radio
- 33 Adjusting the Volume
- 34 Identifying Radio Controls
- 34 Radio Parts and Controls
- 35 Programmable Features
- 36 Assignable Radio Functions
- 39 Assignable Settings or Utility Functions
- 40 Accessing the Preprogrammed Functions
- 40 Menu Select Buttons
- 41 Home Button
- 41 4-Way Navigation Button
- 41 Data Feature Button
- 41 Keypad
- 42 Keypad Characters – Uppercase Mode
- 43 Keypad Characters – Lowercase Mode
- 44 Keypad Characters – Numeric Mode
- 45 Keypad Characters – Hexadecimal Mode
- 46 Push-To-Talk (PTT) Button
- 47 Identifying Status Indicators
- 47 Status Icons
- 52 Text Messaging Service (TMS) Indicators
- 52 TMS Status Icons
- 54 TMS Menu Options
- 54 Call Type Icons
- 55 LED Indicator
- 56 Intelligent Lighting Indicators
- 57 Alert Tones
- 61 Phone Call Displays and Alerts
- 63 General Radio Operation
- 63 Selecting a Zone
- 64 Selecting a Radio Channel
- 64 Selecting a Channel via Channel Search Button
- 65 Mode Select Feature
- 65 Saving a Zone and a Channel to a Softkey
- 66 Saving a Zone and a Channel to a Button
- 66 Receiving and Responding to a Radio Call
- 67 Receiving and Responding to a Talkgroup Call
- 67 Receiving and Responding to a Private Call (Trunking Only)
- 68 Receiving and Responding to a Telephone Call (Trunking Only)
- 68 Making a Radio Call
- 69 Making a Talkgroup Call
- 69 Making a Private Call (Trunking Only)
- 70 Making an Enhanced Private Call (Trunking Only)
- 71 Making a Telephone Call (Trunking Only)
- 72 Switching Between Repeater or Direct Operation Button
- 72 Monitor Feature
- 72 Monitoring a Channel
- 73 Monitoring Conventional Mode
- 74 Advanced Features
- 74 Advanced Call Features
- 74 Selective Call (ASTRO Conventional Only)
- 74 Receiving a Selective Call
- 74 Making a Selective Call
- 75 Talkgroup Call Feature (Conventional Operation Only)
- 75 Selecting a Talkgroup
- 76 Sending a Status Call
- 76 Responding to the Dynamic Regrouping Feature (Trunking Only)
- 77 Requesting a Reprogram (Trunking Only)
- 77 Classification of Regrouped Radios
- 78 Dynamic Zone Programming (DZP)
- 78 Entering the Dynamic Zone to Select a Dynamic Channel
- 79 Saving a Channel in the Dynamic Zone from List Selection
- 79 Saving a Channel in the Dynamic Zone from Channel Name
- 80 Deleting a Channel in the Dynamic Zone
- 80 Contacts
- 81 Making a Private Call from Contacts
- 82 Adding a New Contact Entry
- 83 Deleting a Contact Entry
- 83 Adding a Contact to a Call List
- 84 Removing a Contact from a Call List
- 84 Methods of Contact Editing in a Call List
- 84 Editing an Entry Alias
- 85 Editing as Entry ID
- 85 Editing a Call Type
- 86 Viewing Details of a Contact
- 86 Scan Lists
- 86 Viewing a Scan List
- 86 Editing the Scan List
- 87 Changing the Scan List Status
- 88 Viewing and Changing the Priority Status
- 88 Scan
- 89 Turning Scan On or Off
- 89 Making a Dynamic Priority Change (Conventional Scan Only)
- 89 Deleting a Nuisance Channel
- 90 Restoring a Nuisance Channel
- 90 Call Alert Paging
- 90 Receiving a Call Alert Page
- 90 Sending a Call Alert Page
- 92 Emergency Operation
- 93 Sending an Emergency Alarm
- 93 Sending an Emergency Call (Trunking Only)
- 94 Sending an Emergency Alarm with Emergency Call
- 95 Sending a Silent Emergency Alarm
- 95 Change of Channels during Emergency
- 95 Emergency Keep-Alive Feature
- 96 Fireground (Conventional Only)
- 96 Entering Fireground Zone Channel
- 97 Responding to Evacuation Indicator
- 98 Tactical Public Safety(TPS) (Conventional Only)
- 98 Using TPS Normal Transmission
- 98 Using TPS Emergency Transmission
- 99 Man Down
- 100 Pre-Alert Timer
- 100 Post-Alert Timer
- 101 Radio Alerts When Man Down Feature is Triggered
- 101 Triggering Emergency
- 101 Radio Alerts When Man Down Enhanced is Triggered
- 102 Exiting Man Down Feature
- 102 Re-Initiating Man Down
- 102 Testing the Man Down Feature
- 103 Automatic Registration Service (ARS)
- 103 Selecting or Changing the ARS Mode
- 104 User Login Feature
- 104 Logging In as a User
- 105 Logging Out
- 106 Text Messaging Service (TMS)
- 106 Accessing the Messaging Features
- 107 Composing and Sending a New Text Message
- 108 Sending a Quick Text Message
- 109 Priority Status and Request Reply of a New Text Message
- 109 Appending a Priority Status to a Text Message
- 110 Removing a Priority Status from a Text Message
- 110 Appending a Request Reply to a Text Message
- 110 Removing a Request Reply from a Text Message
- 111 Appending a Priority Status and a Reply Request to a Text Message
- 111 Removing a Priority Status and a Reply Request from a Text Message
- 111 Managing Text Messages
- 111 Receiving a Text Message
- 112 Viewing a Text Message from the Inbox
- 113 Replying to a Received Text Message
- 114 Accessing the Drafts Folder
- 114 Sent Text Messages
- 114 Viewing a Sent Text Message
- 115 Sending a Sent Text Message
- 115 Deleting a Text Message
- 116 Deleting All Text Messages
- 116 ASTRO 25 Advanced Messaging Solution
- 117 System Setup for ASTRO Advanced Messaging Solution
- 117 Two-Factor Authentication
- 118 Logging in via the Two-Factor Authentication
- 119 Logging out of Two-Factor Authentication
- 119 Sending a Query
- 121 Receiving a Query
- 121 Secure Operations
- 122 Selecting Secure Transmissions
- 122 Selecting Clear Transmissions
- 122 Managing Encryption
- 122 Loading an Encryption Key
- 122 Multikey Feature
- 123 Selecting an Encryption Key
- 124 Selecting a Keyset
- 124 Erasing the Selected Encryption Keys
- 125 Requesting an Over-the-Air Rekey (ASTRO Conventional Only)
- 126 MDC Over-the-Air Rekeying (OTAR) Page
- 126 Infinite UKEK Retention
- 126 Hear Clear
- 127 Security
- 127 Radio Lock
- 127 Unlocking Your Radio
- 128 Changing Your Password
- 129 Changing Your Tactical Inhibit Password
- 129 Enabling or Disabling the Radio Lock Feature (Secure Radios Only)
- 130 Radio Stun and Kill
- 130 Radio Stun
- 130 Using Radio Stun
- 130 Radio Kill
- 131 Using Remote Kill to Kill Another Radio
- 131 Using Direct Kill to Kill Your Own Radio
- 131 Global Positioning System (GPS)
- 132 GPS Operation
- 133 GPS Performance Enhancement
- 133 The Outdoor Location Feature (Using GPS)
- 134 Military Grid Reference System (MGRS) Coordinates
- 134 Accessing the Outdoor Location Feature
- 135 Saving a Waypoint
- 136 Viewing a Saved Waypoint
- 136 Editing the Alias of a Waypoint
- 137 Editing the Coordinates of a Waypoint
- 138 Deleting a Single Saved Waypoint
- 139 Deleting All Saved Waypoints
- 139 Measuring the Distance and Bearing from a Saved Waypoint
- 139 Location Feature in Emergency Mode
- 140 Peer-Location on the Display (ASTRO Conventional only)
- 141 Geofence (ASTRO 25 Trunking System)
- 141 Entering the Geofence Area
- 142 Trunking System Controls
- 142 Using the Failsoft System
- 143 Out-of-Range Radio
- 143 Site Trunking Feature
- 143 Locking and Unlocking a Site
- 144 Site Display and Search Button
- 144 Viewing the Current Site
- 144 Changing the Current Site
- 144 Mission Critical Wireless - Bluetooth®-
- 145 Turning the Bluetooth On
- 146 Turning the Bluetooth Off
- 146 Re-Pair Timer
- 147 Bluetooth Drop Timer
- 149 Pairing with Low Frequency-Motorola Proximity Pairing (LF-MPP) Feature
- 150 Radio Indications of Lost Bluetooth Connection
- 150 Standard Pairing Feature
- 151 Searching and Pairing the Bluetooth Device
- 152 Turning Bluetooth Visibility On
- 153 Receiving Pairing Request from other Devices
- 153 Turning Bluetooth Visibility Off
- 153 PIN Authentication in Pairing
- 154 Pairing the Authentication PIN when Receiving a Pairing Request
- 155 Pairing the Authentication PIN with the Generated Numeric PIN
- 156 Pairing the Authentication PIN by Manually Keying in the Same PIN
- 156 Turning On the Bluetooth Audio (Routing the Audio from the Radio to the Headset)
- 157 Turning Off the Bluetooth Audio (Routing the Audio from the Headset to the Radio)
- 157 Adjusting the Volume of the Radio from Bluetooth Audio Device
- 158 Viewing and Clearing the Bluetooth Device Information
- 159 Clearing All Bluetooth Devices Information
- 160 Editing the Bluetooth Friendly Name
- 160 Pairing with LEX 700
- 161 Programming Over Project 25 (POP 25) (ASTRO 25 and ASTRO Conventional)
- 161 Responding to the Notification of Upgrade
- 162 Voice Announcement
- 163 Site Selectable Alerts (ASTRO 25)
- 163 Sending SSA Notification to Single Site
- 164 Sending SSA Notification to Single Site Via Manual Entry
- 165 Sending SSA Notification to All Sites
- 166 Sending SSA Notification to All Available Sites
- 166 Stopping SSA Notification of a Single Site
- 167 Stopping SSA Notification of a Single Site Via Manual Entry
- 167 Stopping SSA Notification of All Sites
- 168 Stopping SSA Notification of All Available Sites
- 168 Long Term Evolution (LTE)
- 170 Data Profiles Available for LTE
- 170 Turning On the LTE at the LTE Menu Screen
- 171 Turning On the LTE with LTE Button
- 172 Turning Off the LTE Connection
- 172 Information at the LTE Screen
- 173 Scenario of Changing from LTE-enabled Channel to LTE-disabled Channel
- 174 Scenario of Changing from LTE-enabled Channel to Unprogrammed Channel
- 174 Scenario of Entering or Exiting Out-of-Range Site
- 174 Utilities
- 174 Viewing Recent Calls
- 175 Using the Flip Display
- 175 Selecting a Basic Zone Bank
- 175 Selecting an Enhanced Zone Bank
- 176 Selecting the Power Level
- 177 Selecting a Radio Profile
- 178 Enabling and Disabling the Radio Alias
- 178 Selecting the Audio Speaker
- 179 Controlling the Display Backlight
- 179 Locking and Unlocking the Keypad and Controls
- 180 Turning the Controls and Keypad Buttons Tones On or Off
- 180 Turning Voice Mute On or Off
- 180 Using the Time-Out Timer
- 181 Time and Date Setup
- 181 Editing the Time and Date
- 182 Using Conventional Squelch Operation Features
- 182 Analog Options
- 182 Digital Options
- 183 Using the PL Defeat Feature
- 183 Digital PTT ID Support
- 183 Smart PTT Feature (Conventional Only)
- 184 Transmit Inhibit
- 184 Enabling Transmit Inhibition
- 185 Disabling Transmit Inhibition
- 185 IMPRES Battery Annunciator
- 186 Accessing the Battery Info screen
- 186 General Radio Information
- 186 Accessing the Radio Information
- 187 Viewing the IP Information
- 188 Viewing the Control Assignments
- 188 Editing the Soft ID
- 190 Helpful Tips
- 190 Radio Care
- 191 Cleaning Your Radio
- 191 Proper Ways to Handle the Radio
- 192 Radio Service and Repair
- 192 Battery Care
- 192 Battery Charge Status
- 192 LED and Sounds
- 192 Fuel Gauge Icons
- 194 Battery Recycling and Disposal
- 195 Accessories
- 196 Maritime Radio Use in the VHF Frequency Range
- 196 Special Channel Assignments
- 196 Emergency Channel
- 196 Non-Commercial Call Channel
- 196 Operating Frequency Requirements
- 199 Declaration of Compliance for the Use of Distress and Safety Frequencies
- 199 Technical Parameters for Interfacing External Data Sources
- 200 Glossary
- 207 Limited Warranty
- 207 MOTOROLA COMMUNICATION PRODUCTS
- 207 I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
- 208 II. GENERAL PROVISIONS:
- 208 III. STATE LAW RIGHTS:
- 208 IV. HOW TO GET WARRANTY SERVICE:
- 209 V. WHAT THIS WARRANTY DOES NOT COVER:
- 209 VI. PATENT AND SOFTWARE PROVISIONS:
- 211 VII. GOVERNING LAW: