VISIX V-Series Hardware Installation Manual

Hardware Installation Manual| VISIX V-Series All-in-One Cameras
VISIX V-Series All-in-One Cameras
Hardware and Installation Manual
v01-2016
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
1
Hardware and Installation Manual| VISIX V-Series All-in-One Cameras
This manual applies to the following camera models. Please use the below links or the Table of Contents
to locate the section of this manual that pertains to your particular All-in-One camera model:
Camera Type
Model
Megapixel Exterior Bullet Camera
VX-2A-B-IWD
Megapixel Exterior Bullet Camera w/Remote Focus
VX-2A-B-RIWD
Megapixel Exterior Dome Camera
VX-2AD3-IWD
Megapixel Interior Mini Dome Camera
VX-2A-IMD-X
VERA 36° Field-of-Vision Thermal Bullet Camera
VX-VT-36
Please use the links above or the Table of Contents to locate the section of this manual that pertains to
your particular All-in-One camera model.
Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to
contact the dealer.
This manual may contain technical inaccuracies or printing errors. The content is subject to change
without notice. The manual will be amended if there are any hardware updates or changes.
Disclaimer Statement
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or
signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
2
Hardware and Installation Manual| VISIX V-Series All-in-One Cameras
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1). This device may not cause harmful interference.
2). This device must accept any interference received, including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
3
Hardware and Installation Manual| VISIX V-Series All-in-One Cameras
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger or
property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
WARNING: Serious injury or death may be caused if any of these warnings are neglected.
CAUTION: Injury or equipment damage may be caused if any of these cautions are neglected.
WARNINGS:

Please adopt a power adapter which can meet the safety extra low voltage (SELV) standard when
possible, and source with 12 VDC or 24 VAC (depending on models) according to the IEC60950-1
and Limited Power Source standard. Before applying power to the camera, check the power
source to ensure that it is within the specifications

If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)

To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture unless
it is an exterior/weatherproof model. Please do not install the camera in a place exposed to direct
sunlight. Do not operate the camera in environments beyond the specified temperature. Refer to
your specific camera model’s section of this manual for environmental conditions and limitations.

This installation should be made by a qualified service person and should conform to all the local
codes.

Please install blackout equipment into the power supply circuit to prevent footage and data loss.

Please make sure that the ceiling can support more than 50(N) Newtons of gravity if the camera is
fixed to the ceiling.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
4
Hardware and Installation Manual| VISIX V-Series All-in-One Cameras
CAUTIONS:

Make sure the power supply voltage is correct before using the camera.

Do not drop the camera or subject it to physical shock.

Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of
ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the
lens cap to protect the sensor from dirt.

Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light
can cause fatal damage to the camera.

The sensor may be burned out by a laser beam, so when any laser equipment is being used, make
sure that the surface of the sensor not be exposed to the laser beam.

Do not place the camera in extremely hot, cold temperatures (the operating temperature should be
between -30°C ~ 60°C, or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp
environment, and do not expose it to high electromagnetic radiation.

To avoid heat accumulation, good ventilation is required for a proper operating environment.

Keep the camera away from water and any liquid.

While shipping, the camera should be packed in its original packing.

Improper use or replacement of the battery may result in hazard of explosion. Please use the
manufacturer recommended battery type.
NOTE:
For cameras that support IR, you are required to pay attention to the following precautions to prevent
IR reflection.

Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover
film until the installation is finished. If there is dust or grease on the dome cover, clean the dome
cover with clean soft cloth and isopropyl alcohol. (only applies to certain models).

Make certain the installation location does not have reflective surfaces of objects too close to the
camera. The IR light from the camera may reflect back into the lens causing reflection. (only
applies to certain models).

The foam ring around the lens must be seated flush against the inner surface of the bubble to
isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly (only applies to certain models).
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
5
Installation and User Manual| VISIX V-Series All-in-One Cameras
Table of Contents
1 VISIX V-Series All-in-One Cameras ...................................................................................................... 8
1.1 Introduction ....................................................................................................................................... 8
2 VX-2A-B-IWD/ VX-2A-B-RIWD - 2MP Exterior Bullet Camera .............................................................. 9
2.1 VX-2A-B-IWD/ VX-2A-B-RIWD Specifications- Quick Summary ......................................................... 9
2.2 Package Contents ............................................................................................................................ 10
2.3 Part Names ...................................................................................................................................... 11
2.4 Installation ....................................................................................................................................... 12
Installing the Camera – Installation without Bracket ...................................................................... 12
Adjusting Angle of the Camera ........................................................................................................ 14
Adjusting Zoom and Focus (VX-2A-B-IWD Model Only) .................................................................. 14
2.5 Connections ..................................................................................................................................... 15
2.6 Full Camera Specifications ............................................................................................................... 17
2.7 Camera Dimensions ......................................................................................................................... 19
3 VX-2AD3-IWD - 2 MP Exterior Dome Camera ................................................................................... 20
3.1 VX-2AD3-IWD Specifications- Quick Summary ................................................................................ 20
3.2 Package Contents ............................................................................................................................ 21
3.3 Part Names ...................................................................................................................................... 22
3.4 Installation ....................................................................................................................................... 23
Installing the Camera – Installation without Bracket ...................................................................... 23
Reattachment of the Dome Cover - Alignment ................................................................................ 25
Adjusting Angle of the Camera ........................................................................................................ 25
3.5 Connections ..................................................................................................................................... 26
3.6 Full Camera Specifications ............................................................................................................... 27
3.7 Camera Dimensions ......................................................................................................................... 29
3.8 Compatible Accessory Installation (Mounts) ................................................................................... 30
Wall Mount- VX-2AD-WM .............................................................................................................. 30
Ceiling Mount- VX-2AD-CM............................................................................................................. 31
Pendant Mount Cap - VX-2AD-PMC ................................................................................................ 34
Gang Box Mount – VX-2AD-GB ........................................................................................................ 35
4 VX-2A-IMD-X - 2 MP Interior Mini Dome Camera ............................................................................. 37
4.1 VX-2A-IMD-X Specifications- Quick Summary ................................................................................. 37
4.2 Package Contents ............................................................................................................................ 38
4.3 Part Names ...................................................................................................................................... 39
4.4 Installation ....................................................................................................................................... 40
Installing the Camera – Installing without Bracket.......................................................................... 40
Adjusting Angle of the Camera ........................................................................................................ 42
4.5 Connections ..................................................................................................................................... 42
4.6 Full Camera Specifications ............................................................................................................... 43
4.7 Camera Dimensions ......................................................................................................................... 45
4.8 Compatible Accessory Installation (Mounts) ................................................................................... 46
Wall Mount - VX-2AIMD-WM .......................................................................................................... 46
Location of the Holes for M3x6L Bolts ............................................................................................. 48
Ceiling Mount - VX-2AD-CM............................................................................................................. 49
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
6
Installation and User Manual| VISIX V-Series All-in-One Cameras
Pendant Mount Cap - VX-2AD-PMC ................................................................................................. 51
5 VX-VT-36 – VERA 36° Thermal Bullet Camera ................................................................................... 53
5.1 VX-VT-36 SPECIFICATIONS – QUICK SUMMARY ......................................................................................... 53
5.2 PACKAGE CONTENTS ............................................................................................................................. 54
5.3 PART NAMES ....................................................................................................................................... 55
5.4 INSTALLATION ...................................................................................................................................... 56
Installing the Camera – Installation without Bracket ...................................................................... 56
Adjusting Angle of the Camera ........................................................................................................ 58
5.5 CONNECTIONS...................................................................................................................................... 59
5.6 FULL CAMERA SPECIFICATIONS ................................................................................................................ 61
5.7 CAMERA DIMENSIONS ........................................................................................................................... 62
6 Power over Ethernet Specifications .................................................................................................. 63
6.1 POWER COMPARISON............................................................................................................................ 63
7 Revision History ............................................................................................................................... 64
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
7
Installation and User Manual| VISIX V-Series All-in-One Cameras
1 VISIX V-Series All-in-One Cameras
1.1 Introduction
VISIX V-Series All-in-One, edge-based IP cameras are powerful, full-featured, VMS and advanced analytic
capable. VISIX V-Series cameras provide a complete surveillance solution for the small and medium sized
businesses and for unique single-point applications.
Several models exist to best suit any number of environments. Hardware installation details for each
model are contained within. Use the Table of Contents to locate the Section pertaining to your particular
camera model.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
8
Installation and User Manual| VISIX V-Series All-in-One Cameras
2 VX-2A-B-IWD/ VX-2A-B-RIWD - 2MP Exterior
Bullet Camera
The VX-2A-B-IWD and VX-2A-B-RIWD are fully functional indoor/outdoor IP cameras with advanced
analytics capabilities. These cameras can be connected to a DVR or act as a standalone recording device.
The exterior bullet camera line offers high-definition video at full 1920 x 1080 resolution for both indoor
and outdoor video surveillance applications which require superior clarity and detail.
The wealth of features includes; dual-streaming of either H.264 or MJPEG compression; wide dynamic
range; Micro SD card slot for local recording; IP66 weather resistant construction; varifocal lens; and IR
illumination. The RIWD model also features remote one-click auto focus.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
2.1 VX-2A-B-IWD/ VX-2A-B-RIWD Specifications- Quick Summary
Component
Feature Description

SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
True Day / Night
DC Auto Iris Lens
WDR
Embedded IR Illuminator
Weather Proof (IP66)
Remote Zoom/Focus Control (One Click AF) - ** VX-2A-B-RIWD Only**
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG(Motion
JPEG)
Max 30fps in 1080p
Text Overlay
Analog Video Output
10/100 Base-T Ethernet
ONVIF compliant (Profile S)
Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)

VCA Presence Standard



Camera





Video



Network
Integration



General
Video Contents
Analysis (VCA)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
9
Installation and User Manual| VISIX V-Series All-in-One Cameras
2.2 Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera
DC Power Adaptor
Universal Plugs
Screws(M4x30) and Plastic Anchors
Quick Installation Guide
Hex Wrench(3mm)
Silicon Waterproof Band
Video Output Cable
Installation Template
NOTE:
The contents above are subject to change without prior notice.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
10
Installation and User Manual| VISIX V-Series All-in-One Cameras
2.3 Part Names
❶
❽
❿
❾
❺
❼
❻
❷
❹
❸
* Models herein and their appearance are subject to change without any prior notice.
1). Sunshield:
Position the sunshield to prevent direct sunshine.
2). Video-Out Cable Socket:
Socket for the video output cable included in the package (CVBS: 1.0Vp-p / 75Ω BNC)
3). PAL/NTSC button:
Pressing the PAL/NTSC button each time changes the mode as follows.
No video output -> PAL-> NTSC
4). Reset button:
Use the button to restart the device or to reset it to Factory Default. Refer to the 3xLOGIC VISIX Allin-One Camera User Manual for more details on restarting/resetting to factory default.
5). Focus Puller:
Use the puller to manually determine correct focus of the camera. Refer to Adjusting Zoom and Focus
for more details.
6). Zoom Puller:
Use the puller to manually determine appropriate field of view of the camera. Refer to Adjusting
Zoom and Focus for more details.
7). microSD memory card slot:
The camera supports up to 32GB. A card with Class 4 and higher is recommended for HD recordings.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
11
Installation and User Manual| VISIX V-Series All-in-One Cameras
8). Terminal Connector:
Connector for cable connection of digital input/output. Refer to Section 2.5: Connections for more
details.
9). Power Adaptor Connector:
Use DC12V for the power supply.
ation template
10). LAN connector:
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
2.4 Installation
INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET
Installation Template
NOTE:
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package separately.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
12
Installation and User Manual| VISIX V-Series All-in-One Cameras
Steps:
1).
Place the installation template included in
the package on the desired installation
surface.
2).
Drill three holes in correct positions based
on the template paper, and insert the
anchor blocks into the holes.
3).
Attach the silicon waterproof band included
in the package to the camera’s mounting
surface by aligning it with the three
alignment holes.
4).
Connect the required cables including a
power cable and a LAN cable (or PoE
connection) to the device. See Section 2.5:
Connections for a diagram of the correct
connections.
5).
Place the camera body to match the three
alignment holes with the three anchor
blocks, and hold the camera against the
surface where the camera will be mounted.
6).
Tighten the anchor blocks with the screws.
7).
Adjust the heading direction of the camera.
Refer to Adjusting Angle of the Camera for
more details.
8).
Adjust zoom and focus of the camera. Refer to Adjusting Zoom and Focus for more details.
9).
Attach the lens cover on the main body by rotating it clockwise.
CAUTION:
Sealing gaps is recommended as gaps may appear after the camera installation. Gaps may cause problems
such as moisture, water leakage, and etc., which negatively affects the operation of the camera if gaps
remain unsealed.
CAUTION:
To prevent products from damage, place the camera on a stable and non-vibrating surface. If the stability
is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
13
Installation and User Manual| VISIX V-Series All-in-One Cameras
ADJUSTING ANGLE OF THE CAMERA
Adjust the camera to the desired angle by unscrewing the joints referring to the following pictures.
Adjust the joint to install
the camera on the wall.
Steps:
1).
Tilting adjustment
Insert the video output cable (included in the
package) to the video output cable socket,
and
SD Card
connect it to an analogue video test monitor to
check if the camera angle has been set as
intended. If the angle is appropriate, disconnect
the camera from the analogue monitor, and then
remove the video output cable from the camera.
Panning adjustment
Video output
Out
cableVideo
socket
Reset
PAL/NTSC
ADJUSTING ZOOM AND FOCUS
(VX-2A-B-IWD MODEL ONLY)
Steps:
1).
Unscrew the zoom puller and the focus puller
counter-clockwise.
2).
Adjust the zoom and the focus of the lens.
3).
Tighten the zoom puller and the focus puller again by
turning it clockwise after the zoom and the focus are
properly adjusted.
Focus Puller
Zoom Puller
CAUTION:
Manual adjustment of Zoom and Focus is only possible on the VX-2A-B-IWD model version. Zoom and
Focus controls can be configured digitally from the camera’s web interface for VX-2A-B-RIWD models.
See the VISIX V-Series All-in-One Camera User Manual for more details on adjusting lens settings from
the camera’s web interface.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
14
Installation and User Manual| VISIX V-Series All-in-One Cameras
2.5 Connections
GREEN : DI
WHITE : DI COM
ORANGE : DO
YELLOW : DO COM
LAN cable
❶
❷
❸
❹
(not included)
DC 12V
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
15
Installation and User Manual| VISIX V-Series All-in-One Cameras
1). Sensor (DI) connection:
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the following
figures. Settings can be done through the camera’s webpage.

Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA.
CAUTION:
Do not exceed the maximum input voltage or relay rate.
Internal
+3.3V
Internal
DI
Output of
Sensor
+
DI
-
COM
COM
Relay Type
Output of
Sensor
+
-
-
+
Voltage Type
2). Alarm (DO) Connection:
Only the relay type is supported.

Relay Rating: Max 24VDC 50mA
CAUTION:
Do not exceed the maximum relay rating.
Internal
Device
DO
COM
Relay Type
3). LAN Connection:
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45. to connect
the device to a hub or a router in the network. Refer to Section 6: Power over Ethernet
Specifications to for further detail.
4). Power Connection:
The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer to
Section 6: Power over Ethernet Specifications for further detail.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
16
Installation and User Manual| VISIX V-Series All-in-One Cameras
2.6 Full Camera Specifications
Camera Module
CMOS
Image Sensor
SONY EXMOR 1/2.9” 1080p CMOS
Effective Pixels
1920x1080
Scanning system
Progressive scanning
Electrical
Resolution
Min. Illumination
AGC Control
Lens
1920 x 1080
Color: 0.7 lux, BW: 0 lux (IR LED On)
Auto
3.0(w) – 9.0mm(t), F1.5(w) – F2.5(t), Optical 3x
Day & Night
Wide Dynamic
Range
Removable IR Cut Filter
Digital WDR
IR Illuminator
IR LED
IR Working
Distance
High Power IR LED x 12 (850nm)
Max. 30m (98ft)
Video
Compression
Format
Number of
Streams
H.264 and MJPEG Selectable per Stream
Dual Stream, Configurable
Resolution
Compression FPS
Motion Detection
Burnt-in Text
(Digital)
Analogue Output
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
30fps@1080p
Built-in
Time stamp and text caption overlay
NTSC/PAL
Audio
Input/output
Compression
Format
-
Function
Digital
Input/Output
RS-485
1/1 channel
Not supported
Network
10/100 Base-T
Power over
Ethernet (PoE)
Supported
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
17
Installation and User Manual| VISIX V-Series All-in-One Cameras
Camera Module
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIBII), IGMP, ICMP, SSLv2/v3, TLSv1
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
Protocol
SD Slot
Electrical Characteristics
Power Source
Power
Consumption
Video Output
Audio Input
Audio Output
D/I
DC 12V / PoE
Max. 6W @ DC 12V
1 Vp-p, 75, Composite
Max 50mA@5VDC, TTL level 1.5V threshold
Max 50mA@24VDC
On-state resistance: 50  (max continuious)
D/O
Environment Condition
Operating
Temperature
Operating
Humidity
[DC12V] -20°C ~ 50°C (-4°F ~ 122°F)
[PoE] -20°C ~ 50°C (-4°F ~ 122°F)
Up to 85% RH
Mechanical Condition
Material
Color
Dimension
Weight (Approx.)
Aluminum Die-Casting
Ivory
83.5mm X 86mm X 287 mm
860g (1.90lbs)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
18
Installation and User Manual| VISIX V-Series All-in-One Cameras
2.7 Camera Dimensions
3.29 in. (83.5 mm)
4.67 in. (118.5 mm)
3.39 in. (86 mm)
9.41 in. (239 mm)
3.29 in. (83.5 mm)
 2.68 in.
(68 mm)
3 x .197 in. (5mm)
11.02 in. (280 mm)
11.30 in. (287 mm)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
19
Installation and User Manual| VISIX V-Series All-in-One Cameras
3 VX-2AD3-IWD - 2 MP Exterior Dome Camera
The VX-2AD3-IWD is a fully functional indoor/outdoor IP camera with advanced analytics capabilities.
These cameras can be connected to a DVR or act as a standalone recording device.
The exterior dome offers high-definition video at full 1920 x 1080 resolution for both indoor and
outdoor video surveillance applications which require superior clarity and detail. Its many features
include; dual-streaming of either H.264 or MJPEG compression; wide dynamic range; Micro SD card slot
for local recording; IP66 weather resistant construction and IR illumination.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software allows the camera to be run as a stand-alone
device recording video to the onboard memory card. This makes the camera compatible with the
existing 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or set it up on your mobile device or tablet using our easy to use QR code quick setup.
3.1 VX-2AD3-IWD Specifications- Quick Summary
Component
Feature Description


Camera



Video


Network
Integration



Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)

VCA Presence Standard

General
Video Contents
Analysis (VCA)
1/2.9” 1080p CMOS Image Sensor
True Day/Night
WDR
Embedded IR Illuminator
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG(Motion
JPEG)
Max 30fps in 1080p
Text Overlay
10/100 Base-T Ethernet
ONVIF compliant (Profile S)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
20
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.2 Package
Contents
Camera
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera
Camera
Screw(M4x35) & Plastic Anchors
Cable
Camera
Cable
Camera
Camera
Camera
Camera
Cable
O-ring &
Waterproof Bracket
Torx Wrench
Cable
Cable
Quick Installation Guide
Screw &
Cable
O-ring &
Waterproof Bracket
Torx (T20)
WrenchWrench
Torx
Plastic
Anchor-3pcs
Cable
Torx Wrench
Torx Wrench
O-ring &
O-ring
&
Waterproof
Bracket
Waterproof Bracket
Cable
Screw &
Screw &
Plastic Anchor-3pcs
Plastic Anchor-3pcs
O-ring &
Waterproof Br
Torx Wrench
Installation Template
O-ring & Waterproof Bracket
O-ring &
Waterproof Bracket
Torx Wrench
Screw &
Plastic Anchor-3pcs
Bottom Pad
Quick Installation Guide
Torx Wrench
O-ring &
Quick Installation Guide
Quick Installation
Waterproof Bracket
Bottom Pad
Bottom Pad
Installation Template
Quick Installation Guide
Installation Template
Guide
Installation Template
Screw
& & AC Plug
Adaptor
Plastic Anchor-3pcs
Bottom Pad
O-ring &
Waterproof Bracket
ch
Bottom Pad
Screw &
Plastic Anchor-3pcs
Bottom Pad
Adaptor & AC Plug
Adaptor & AC Plug
Quick Install
Adaptor & ACBottom
Plug Pad
Adaptor & AC Plug
Quick Installation Guide
NOTE:
The contents above are subject to change without prior notice.
Installation Template
Bottom Pad
Quick Installation Guide
Installation Template
ad
Quick Installation Guide
Installation Template
Adaptor & AC Plug
Adaptor & AC Plug
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
21
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.3 Part Names
Safety
Wire
❶ Safety
Wire
❸
mircoSD/SDHC Card Slot
microSD/SDHC Card Slot
Reset Button
❷
Ambient Light Sensor
Ambient Light Sensor
RJ-45
❺ RJ-45
❹
DC Power
DC Power
Reset Button
❻
* Models herein and their appearance are subject to change without any prior notice.
1). Safety Wire:
The dome cover is attached to the camera body with this safety wire to prevent the dome cover
from being dropped.
2). Ambient Light Sensor:
Used to detect the level or the intensity of light for the IR operation. The sensor should not be
blocked by any object.
3). MicroSD/SDHC Card Slot:
Up to 32GB supported. Class 4 and higher recommended for HD recordings.
4). Reset Button:
Use the button to restart the device or to reset it to Factory Default. Refer to the 3xLOGIC VISIX Allin-One Camera User Manual for more details on restarting/resetting to factory default.
5). RJ-45:
Connect an RJ-45 LAN cable for 10/100 Base-T Ethernet (PoE supported).
6). DC Power Jack:
Connect the provided DC12V adaptor for the power supply unless it is PoE powered.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
22
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.4 Installation
INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET
Installation Template
 4.92 in.
(125 mm)
Mounting templa te
 .255 in. (6.5 mm)
CAUTION:
Installation template’s image size scale in this installation guide is not 1:1. The correct-size template paper
can be found inside the product packaging.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
23
Installation and User Manual| VISIX V-Series All-in-One Cameras
Steps:
1).
Place the installation template included in the
package on the desired installation surface.
2).
Drill two holes for the plastic anchors and a big
hole for the cable lines based on the template
paper, and insert the plastic anchors into the
drilled holes.
3).
Attach the provided bottom pad to the bottom of
the camera body for the prevention of water
permeation.
4).
Detach the dome cover from the camera body by
loosening the three screws with the provided T20
Torx wrench.
5).
Make the screws (M4x35) ready for the
installation: Insert the provided waterproof
bracket and the O-ring into the screw in a row by
placing the head of the bracket beneath the screw
head by reference to the squared image on the
left.
6).
Take the camera to the ceiling, and connect the
necessary cables including a LAN and power cable
(or PoE cable) dropped from the ceiling to the
corresponding connectors on the camera.
7).
Align the screw holes on both sides of the camera
body and the installation surface, insert the screws
prepared at the step 5 into the screw holes on the
camera body, and tighten them into the plastic
anchors on the ceiling with a screw driver.
8).
Adjust the angle of the camera. Refer to Adjusting
Angle of the Camera for more details.
9).
Reattach the dome cover to the camera body by
aligning the screws on the dome cover with the
alignment holes on the camera body. Refer to the
caution below for the alignment method.
Bottom
Pad
O-Ring
Waterproof Bracket
Torx Bolt
(M4 x 20)
Screw
(M4x35)
10). Once properly aligned, tighten the screws into the
camera body with the provided Torx wrench for
the firm attachment of the dome cover. Then,
remove the protection film from the dome cover.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
24
Installation and User Manual| VISIX V-Series All-in-One Cameras
REATTACHMENT OF DOME COVER – ALIGNMENT
The screw hole where the cable line passes has a block next to it due to the cables
underneath. Thus, the part shaped differently from the other two screw hole parts
shall be aligned with the corresponding part of the dome cover, which is also shaped
differently from the other two parts.
Refer to the image on the right for the clarification.
CAUTION:
Do not forcefully pull or shake the dome cover as it is linked to the camera body with a safety wire.
Reset Button
CAUTION:
To prevent products from damage, install the camera on stable and non-vibrating surfaces. If the stability
of a mount surface is in doubt, consult the safety personnel for reinforcements, and then proceed with
the installation.
ADJUSTING ANGLE OF THE CAMERA
Adjust the angle of the camera by manually moving the corresponding parts by reference to the directions
below.
Inner Liner
Gimbal Bracket
Camera Gimbal
Tilt Stopper Screw
Gimbal Bracket
A. To pan, rotate the gimbal
bracket horizontally.
B. To tilt, tilt the camera gimbal by
vertically adjusting it.
C. For the horizontal rotation of
the lens, rotate the inner liner
clockwise or counter-clockwise
with the inner liner.
CAUTION:
Refrain from continuous rotation of the camera gimbal or the inner liner to a single direction as they are
attached to the IR-LED cable inside.
CAUTION:
Be careful not to make the ambient light sensor hidden by the dome cover when adjusting the camera
angle. The ambient light sensor shall be uncovered for its normal operation.
NOTE:
Tighten the tilt stopper screw after the angle adjustment is completed.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
25
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.5 Connections
Camera
RJ-45
DC Power
❷
Cable
❶
LAN cable
Power Adaptor
1). LAN Connection:
O-ring &
TorxBase-T
Wrench
This is a RJ45 LAN connector for 10/100
Ethernet. Use the Ethernet
cable (RJ45Bracket
to connect the
Waterproof
device to a hub or a router in the network. Refer to Section 6: Power over Ethernet Specifications for
further detail.
2). Power Connection:
The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer to
Section 6: Power over Ethernet Specifications for further detail.
Screw &
Plastic
Bottom Pad
Quick Installation Guide
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
Adaptor & AC Plug
Installat
26
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.6 Full Camera Specifications
Camera Module
CMOS
Image Sensor
1/2.9” 1080p CMOS
Effective Pixels
1920x1080
Scanning system
Progressive scanning
Electrical
Resolution
Min. Illumination
AGC Control
Lens
1920 x 1080
Color: 0.5 lux, BW: 0 lux (IR LED On)
Auto
4.0mm, F1.8
Day & Night
Wide Dynamic
Range
True Day & Night
Digital WDR
Video
Compression
Format
Number of
Streams
Resolution
Compression FPS
Motion Detection
Burnt-in Text
(Digital)
H.264 Baseline, Main, High profile(MPEG-4 Part 10/ AVC),
MJPEG(Motion JPEG)
Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
30fps@1080p
Built-in
Video stream overlay text
Audio
Input/output
Compression
Format
-
Function
Digital
Input/Output
RS-485
Network
10/100 Base-T
Power over
Ethernet (PoE)
Protocol
SD Slot
Supported
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIBII), IGMP, ICMP, SSLv2/v3, TLSv1
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
27
Installation and User Manual| VISIX V-Series All-in-One Cameras
Camera Module
Electrical Characteristics
Power Source
Power
Consumption
Video Output
Audio Input
Audio Output
D/I
D/O
DC 12V / PoE IEEE802.3af (Class 0)
Max. 5.4 W @ DC 12V
-
Environment Condition
Operating
Temperature
Operating
Humidity
-20˚C ~ 50˚C (-4˚F ~ 122˚F)
Up to 85% RH
Mechanical Condition
Material
Color
Dimension
Weight (Approx.)
Aluminum Die-Casting (Vandal Resistance)
Ivory
Housing: 125 (Ø) x 74.5 (H) mm
Dome: 65(Ø) mm
455g (1lb)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
28
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.7 Camera Dimensions
Mounting
 4.92 in. (125 mm)
 2.56 in. (65 mm)
1.35 in. (34.3 mm)
1.58 in. (40.2 mm)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
29
Installation and User Manual| VISIX V-Series All-in-One Cameras
3.8 Compatible Accessory Installation (Mounts)
The following are the various combinations of the compatible accessories to mount this camera model.
Model Names & Combinations

VX-2AD-WM + VX-2AD-PMC

VX-2AD-CM + VX-2AD-PMC

VX-2AD-GB
Refer to the corresponding accessory model’s installation guide for the instructions.
Model Image
VX-2AD-WM
VX-2AD-CM
VX-2AD-PMC
VX-2AD-GB
WALL MOUNT- VX-2AD-WM
Contents
A
D
B
D
C
A
C
A-A-A : IPN3202HD
B-B : IPN352HD & IPX5502HD
C-C : IPN3402HD
D-D-D : IPN2103HD & IPN3102HD & IPN3502HD
B
A
D
A
C
B
D
Wall Mount Bracket x 1
M5 Tapping Screw x 4
Plastic Anchor x 4
C
B
D
A-A : IPN352HD & IPX5502HD
B-B-B : IPN3202HD
C-C-C : IPN2103HD & IPN31
D-D : IPN3402HD
Waterproof Gasket x 1
A
B
C
Installation
Steps:
1).
Cover the wall mount bracket with the waterproof gasket like the image on the left.
Waterproof Gasket
W
Wall Mount Bracket
W
NPT 1-1/4”
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
30
Installation and User Manual| VISIX V-Series All-in-One Cameras
2).
Drill the four holes on the installation surface based on the screw holes on the wall mount
bracket, and insert the plastic anchors into the holes. Then, insert the tapping screws through
the screw holes on the wall mount bracket into the anchor blocks to tighten the bracket into
the wall
Attach an Additional Bracket
3).
Attach an additional bracket at the bottom of VX-2AD-WM by referencing to the bracket’s
installation section, Pendant Mount Cap - VX-2AD-PMC.
Waterproof Gasket
W
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
31
Installation and User Manual| VISIX V-Series All-in-One Cameras
CEILING MOUNT- VX-2AD-CM
Contents
Ceiling Mount Bracket x 1
M5 Tapping Screw x 4
Plastic Anchor x 4
Waterproof Gasket x 1
Installation
Steps:
1).
2).
Cover the ceiling mount bracket with the waterproof gasket like the squared image on the left.
Drill the four holes on the installation surface based on the screw holes on the ceiling mount
bracket, and insert the plastic anchors into the holes. Then, insert the tapping screws through
the screw holes on the ceiling mount bracket into the anchor blocks to tighten the bracket into
the ceiling.
Waterproof
Gasket
Wall Mount Bracket
W
NPT 1-1/4”
Plastic Anchor
Ceiling Mount Bracket
W
Tapping Screw
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
32
Installation and User Manual| VISIX V-Series All-in-One Cameras
Attach an Additional Bracket
3). Attach an additional pendant bracket at
the bottom of VX-2AD-CM by referencing
to the bracket’s installation section,
Pendant Mount Cap - VX-2AD-PMC.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
33
Installation and User Manual| VISIX V-Series All-in-One Cameras
PENDANT MOUNT CAP - VX-2AD-PMC
Contents
(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2
A
D
B
D
A
C
C
A-A-A : IPN3202HD
B-B : IPN352HD & IPX5502HD
C-C : IPN3402HD
D-D-D : IPN2103HD & IPN3102HD & IPN3502HD
VX-2AD-PMC
(M4 x 12 bolt & O-Ring) x 4
B
A
D
Installation
Steps:
1).
502HD
02HD
D & IPX5502HD
HD
03HD & IPN3102HD & IPN3502HD
Install your camera at the bottom of VX-2AD-PMC with the corresponding bolts by reference
to the screw hole below.
VX-2AD-CM
VX-2AD-PMC
Screw Holes Guide for Camera
The image below shows the bottom of VX-2AD-CM with the screw holes specific to the VX-2AD3-IWD
camera model (labelled as B). Refer to the screw hole information below to attach the VX-2AD3-IWD
camera to the VX-2AD-CM mount.
A
D
B
D
C
A
C
A-A-A : IPN3202HD
B-B
: IPN352HD & IPX5502HD
B: VX-2AD3-IWD
C-C : IPN3402HD
D-D-D : IPN2103HD & IPN3102HD & IPN3502HD
B
A
D
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
34
Installation and User Manual| VISIX V-Series All-in-One Cameras
GANG BOX MOUNT – VX-2AD-GB
Contents
(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2
M4 x 20 bolt x 4
VX-2AD-GB
Installation
The images below show how to attach VX-2AD-GB to gang boxes of four different types.
Refer to the screw hole information to attach VX-2AD-GB to your gang box.
Single Gang Box
Double AGang Box
C
C
B
D
2HD
A-A : IPN
B-B-B : I
C-C-C :
D-D : IPN
B
D
N3102HD & IPN3502HD
D
A
B
< VX-2AD-GB attached to a single gang box >
A
C
C
Octo Gang Box 1
B
D
A
B
C
B
A
D
02HD & IPN3502HD
Octo Gang Box 2
B
D
C
D
A
C attached to a double gang box >
< VX-2AD-GB
A-A : IPN352HD & IPX5502HD
B-B-B : IPN3202HD
C-C-C : IPN2103HD & IPN3102HD & IPN3502HD
D-D : IPN3402HD
A-A : IPN352HD & IPX5502HD
B-B-B : IPN3202HD
C-C-C : IPN2103HD & IPN3102HD & IPN3502HD
D-D : IPN3402HD
B
B
C
C
< VX-2AD-GB attached to a 70mm octo gang
box >
< VX-2AD-GB attached to a 3.5”octo gang box >
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
35
Installation and User Manual| VISIX V-Series All-in-One Cameras
Screw Holes Guide for Camera
The image below shows the bottom of VX-2AD-GB with the screw holes specific to the VX-2AD3-IWD
camera model (labelled as A). Refer to the screw hole information below to attach the VX-2AD3-IWD
camera to the VX-2AD-GB mount.
A
C
B
C
B
D
D
A
A-A
: IPN352HD & IPX5502HD
A: VX-2AD3-IWD
B-B-B : IPN3202HD
C-C-C : IPN2103HD & IPN3102HD & IPN3502HD
D-D : IPN3402HD
B
C
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
36
Installation and User Manual| VISIX V-Series All-in-One Cameras
4 VX-2A-IMD-X - 2 MP Interior Mini Dome Camera
The VX-2A-IMD-X is a fully functional indoor IP camera with advanced analytics capabilities. These
cameras can be connected to a DVR or act as a standalone recording device.
The interior mini dome offers high-definition video at full 1920 x 1080 resolution for indoor video
surveillance applications which require superior clarity and detail. Its many features include; dualstreaming of either H.264 or MJPEG compression; Micro SD card slot for local recording; and an
unobtrusive dome design.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
4.1 VX-2A-IMD-X Specifications- Quick Summary
Component
Feature Description

1/2.7” 1080p CMOS Image Sensor
Digital Day/Night
WDR
Vandal Proof (IK09)
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion
JPEG)
Max 30fps in 1080p
Text Overlay
10/100 Base-T Ethernet
ONVIF compliant (Profile S)
Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)

VCA Presence Standard


Camera



Video


Network
Integration



General
Video Contents
Analysis (VCA)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
37
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.2 Package Contents
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera
Screws(M4x20) and anchor blocks
Quick Installation Guide
Torx Wrench(T-10)
White Plug
Installation Template
NOTE:
The contents above are subject to change without prior notice.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
38
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.3 Part Names
❸
❷
❶
* Models herein and their appearance are subject to change without any prior notice.
1). LAN connector:
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
2). Reset button:
Use the button to restart the device or to reset it to Factory Default. Refer to the 3xLOGIC VISIX Allin-One Camera User Manual for more details on restarting/resetting to factory default.
3). microSD/SDHC card slot:
Supports up to 32GB. Recommend Class 4 and higher for HD recordings.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
39
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.4 Installation
INSTALLING THE CAMERA – INSTALLING WITHOUT BRACKET
Installation Template
2 x .236 in. (6 mm)
3.35 in. (85 mm)
CAUTION:
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package separately.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
40
Installation and User Manual| VISIX V-Series All-in-One Cameras
Steps:
1).
Place the installation template included in the
package on the desired installation surface.
2).
Drill two holes in the correct positions based
on the paper mounting template, insert the
plastic anchors into the holes, and tighten
them into the holes.
3).
Loosen the two bolts on the dome cover with
the provided torx wrench (T-10) to open the
dome cover.
4).
Connect necessary cables including a LAN cable
and a power cable to the camera.
5).
Place the camera body to match the alignment
holes with the provided plastic anchors, and
hold the camera against the surface where the
camera will be mounted.
6).
Tighten the plastic anchors with the provided
screws (M4x20).
7).
Once you can see the video on the camera,
adjust the angle of the camera. Refer to
Adjusting Angle of the Camera for more details.
8).
Place the dome cover on the camera's main
body to close the dome cover. Dome cover has
two alignment holes that match the camera
body’s alignment holes.
9).
Once properly placed, tighten the bolts with
the provided torx wrench (T-10).
10). As the last step, insert the white plugs into the
screw holes on the dome to keep the dome
cover neatly.
CAUTION:
To prevent products from damage, place the camera on stable and non-vibrating surfaces If the stability
is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
41
Installation and User Manual| VISIX V-Series All-in-One Cameras
ADJUSTING ANGLE OF THE CAMERA
Adjust the angle of the camera by manually moving the corresponding parts following the directions
below.
A. To tilt, tilt the lens by vertically
adjusting the camera gimbal.
B. To pan, rotate the lower
body of the camera gimbal.
C. Rotate the lens
with upper lens shell
4.5 Connections
❷
Connection Status LEDs
❶
LAN Connection
1). LAN Connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45. to connect
the device to a hub or a router in the network. Refer to Section 6: Power over Ethernet Specfications
for further detail.
2). Connection Status Indicators
Two LEDs are located near the SD card slot, and you can check the connecting status by observing the
LED on the right side.

Solid red – The device is in the process of booting.

Blinking green – Booting is completed.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
42
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.6 Full Camera Specifications
Camera Module
CMOS
Image Sensor
1/2.7” 1080p CMOS
Effective Pixels
1920x1080
Scanning system
Progressive scanning
Electrical
Resolution
Min. Illumination
AGC Control
Lens
1920 x 1080
Color: 1.0Lux B/W : 0.001 Lux (DSS ON)
Auto
2.0mm, F2.0
Day & Night
Wide Dynamic
Range
Digital Day & Night
Digital WDR
Video
Compression
Format
Number of
Streams
Resolution
Compression FPS
Motion Detection
Burnt-in Text
(Digital)
H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC),
MJPEG (Motion JPEG)
Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
30fps@1080p
Built-in
Video stream overlay text
Audio
Input/output
Compression
Format
-
Function
Digital
Input/Output
RS-485
-
Network
10/100 Base-T
Power over
Ethernet (PoE)
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIBII), IGMP, ICMP, SSLv2/v3, TLSv1
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
43
Installation and User Manual| VISIX V-Series All-in-One Cameras
Camera Module
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
SD Slot
Electrical Characteristics
Power Source
Power
Consumption
Video Output
Audio Input
Audio Output
D/I
D/O
PoE IEEE802.3af (Class 2)
2.4W @ PoE
-
Environment Condition
Operating
Temperature
Operating
Humidity
Operating Range
PoE : 0 ˚C ~ 40 ˚C (32˚F ~ 104˚F)
Up to 85% RH
Mechanical Condition
Material
Color
Dimension
Weight (Approx.)
Aluminum Die-Casting (Vandal Resistance)
Ivory
Housing: 105.5 (Ø) x 55.5(H) mm
Dome : 27.5(Ø) mm
270g (0.6lb)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
44
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.7 Camera Dimensions
R 2.19 in. (55.5 mm)
R 1.08 in.
(27.5 mm)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
45
Installation and User Manual| VISIX V-Series All-in-One Cameras
4.8 Compatible Accessory Installation (Mounts)
The compatible accessories to mount this camera model are as follows.
Model Names & Combinations

VX-2AIMD-CM

VX-2AIMD-WM

VX-2AIMD-CM + VX-2AIMD-PMC

VX-2AIMD-GB
The installation instructions for each bracket are contained within the proceeding sections of this manual.
Model Image
VX-2AIMD-CM
VX-2AIMD-CM
VX-2AIMD-PMC
VX-2AIDM-GB
WALL MOUNT - VX-2AIMD-WM
WMB-3202/CMB-3202
202/CMB-3202
Contents
This guide
illustrates
how
to mount
assemble
illustrates
how to
assemble the
corner
adapterthe
and corner mount adapter and
pole mount adapter.
adapter.
etter
of the
alphabet
each adapter
and tighten
Check
the
letterassigned
of the to
alphabet
assigned
to each adapter and tighten
in the corresponding holes to assemble the adapter.
the screws in the corresponding holes to assemble the adapter.
A-A-A(M3TAP)
MODEL : IPN3202HD
A
B
B-B(M3TAP)
MODEL : IPN302HD
A
A
B
Plastic Anchor 3ea
Tapping Screw 3ea
B-B(M3TAP)
MODEL : IPN302HD
er mount adapter and
chBadapter and tighten
mble Athe adapter.
A-A-A(M3TAP)
MODEL : IPN3202HD
A
Wall Mount Bracket
M3x6L BOLT 4ea
B
A
A-A-A(M3TAP)
MODEL : IPN3202HD
B-B(M3TAP)
MODEL : IPN302HD
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
46
Installation and User Manual| VISIX V-Series All-in-One Cameras
Installation
Steps:
1).
Drill three small holes for plastic anchor and one hole for cabling work on the ceiling based on
the holes of the bracket. Refer to Location of the Holes for M3x6L Bolts on the next page to
identify the holes information.
2).
Insert the plastic anchors (3ea) to the drilled three holes.
3).
Fix the bracket on the wall by tightening the tapping screws (3ea) into the plastic anchors.
4).
Detach the dome cover from the camera by loosening the bolts with the hex wrench included
in the camera package.
5).
Fix the camera at the bottom of the bracket with the M3x6L bolts. Ensure that the necessary
cables are properly connected to the camera.
6).
For the last parts of the installation, refer to the steps 7 to 10 in Section 4.4: Installing the
Camera - Installation without Bracket of this manual.
Plastic Anchor
Tapping Screw
Wall Mounting Bracket
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
47
Installation and User Manual| VISIX V-Series All-in-One Cameras
LOCATION OF THE HOLES FOR M3X6L BOLTS
WMB-3202/CMB-3202
The image below shows which spots the camera should be attached to on the wall mount bracket (VXThis2AIMD-CM).
guide illustrates how to assemble the corner mount adapter and
pole
mount
Identify
theadapter.
location of the holes with the alphabet letter, B, on the bracket, and insert the M3x6L bolts
Check
the
letter
of the
in the holes to attach
thealphabet
camera. assigned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M3TAP)
IPN3202HD
B-B(M3TAP)
IPN302HD
B
A
A
B
A
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
48
Installation and User Manual| VISIX V-Series All-in-One Cameras
CEILING MOUNT - VX-2AD-CM
Contents
Plastic Anchor 3ea
Ceiling Mount Bracket
Tapping Screw 3ea
Installation Template 1ea
Installation
Steps:
1).
Drill three holes for the plastic anchors based on the installation template as well as the hole
for the cable dropped from the ceiling. Then, route the LAN cable through the bracket’s pipe.
Ceiling Mount Bracket
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
49
Installation and User Manual| VISIX V-Series All-in-One Cameras
2).
Insert the three anchor blocks into the holes on the ceiling.
3).
Fix the bracket to the ceiling by inserting the tapping screws into the anchor blocks and
tightening them for the firm attachment.
4).
This ceiling mount bracket normally requires a pendant mount cap to attach the camera. Refer
to the installation method in Pendant Mount Cap on the next page.
Plastic Anchor
Tapping Screw
Ceiling Mount Bracket
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
50
Installation and User Manual| VISIX V-Series All-in-One Cameras
PENDANT MOUNT CAP - VX-2AD-PMC
Contents
M5x6L Hex Socket Set Screw 1EA
(pre-installed)
3ea
2.5mm Hex Wrench 1EA
Pendant Mount Cap
M4x8L Hex Wrench Bolt 2EA
Installation
Ceiling Mount Bracket
(Model No: VX-2AD-PMC)
Set Screw
Hex Wrench
Pendant Mount Cap
Steps:
1).
Rotate the pendant mount cap counterclockwise on the thread at the bottom of the ceiling
mount bracket, and tighten the set screw (installed on the pendant mount cap) with the hex
wrench included in the bracket package for the firm attachment of the pendant mount cap.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
51
Installation and User Manual| VISIX V-Series All-in-One Cameras
Biscuit Camera
M4x8L Hex Wrench Bolt
Hex Wrench
2).
Connect your LAN (or PoE) cable from the ceiling pipe to the LAN connector on the camera,
and insert the camera into the pendant mount cap. Then, fix the camera to the pendant
mount cap by inserting the bolts (M4x8L) to the alignment holes on the pendant mount cap
and tightening them with the hex wrench included in the camera package.
3).
For the last part of the installation, refer to steps 7 to 10 in Section 4.4: Installing the Camera –
Installation without Bracket in this manual.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
52
Installation and User Manual| VISIX V-Series All-in-One Cameras
5 VX-VT-36 – VERA 36° Thermal Bullet Camera
The VX-VT-36 indoor/outdoor thermal bullet gives you the advantage to see where you couldn’t before.
When using high-contrast thermal imaging the results are a dramatic reduction in false alarms. Our
thermal camera stands out from the pack with verification and detection in an all-in-one device. Easy
setup and integration using our QR code makes this a perfect camera for any application.
The exterior thermal camera is not affected by changes in lighting, low contrast scenes or inclement
weather. There is no illumination required.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics, coupled with thermal technology allow for object
classification, direction, people counting, dwell times, video alarm verification, retail traffic flow, queue
management and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
5.1 VX-VT-36 Specifications – Quick Summary
Component
Feature Description

17 ㎛ vanadium oxide microbolometer technology
206x156 array size / various resolutions via scale-up
36 degree field-of-view
Dual streaming supported
Burnt-in text (OSD) supported
Unicast/Multicast supported
H.264 and MJPEG(Motion JPEG)
Max 9fps in all resolutions
Text Overlay
Video Motion Detection Supported
Two-way audio streaming
Audio compression: G.711 µLaw
1 Digital Input / 2 Digital Outputs
RTSP/HTTP Protocols supported
10/100 Base-T Ethernet

ONVIF compliant (Profile S)


Micro SD/SDHC Card Embedded
Power over Ethernet (PoE)

VCA Presence Standard

Camera



Streaming




Video



Audio

Sensor/Alarm


Network
Integration
General
Video Contents
Analysis (VCA)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
53
Torx Wrench
Screw &
Plastic Anchor
Installation and User Manual| VISIX V-Series All-in-One Cameras
5.2 Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
WALL CUSHION
Camera
Quick Installation Guide
DC Power Adaptor & Universal Plugs
Torx &
Wrench
Adaptor
AC Plug
Screws (M4x30) & Plastic Anchors
Installation Tem
Torx Wrench
CABEL CORE
Wall Cushion
Screw &
Plastic Anchor-3pcs
Torx Wrench
Screw
&
Quick Installation
Guide
Plastic Anchor-3pcs
WALL CUSHION
WALL CUSHION
Screw &
TorxPlastic
Wrench
(T20 M4x23)
Anchor-3pcs
Installation Template
Quick Ins
Quick Start Guide
Adaptor & AC Plug
CABEL CORE
Torx Wrench
Ferrite Core
Quick Installation Guide
ZCAT1518-0730
WALL CUSHION
Quick Installation
Guide
Installation
Template
Screw &
Adaptor & AC Plug
Plastic Anchor-3pcs
Installation Template
ZCAT2132-1130
NOTE:
The contents above are subject to change without
prior notice.
Adaptor & AC Plug
CABEL CORE
Installation Template
WALL CUSHION
CABEL CORE
Quick Installation Guide
Installation Template
CABEL CORE
Adaptor & AC Plug
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
54
rew &
astic Anchor-3pcs
Installation and User Manual| VISIX V-Series All-in-One Cameras
5.3 Part Names
allation Template
 Sunshield
❶
BLACK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
AUD IN
AUD GND
AUD OUT
DI
DI COM
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
adaptor
❹Powerconnector
❸ LAN connector
 Audio|Sensor|Alarm
❷
connection cables
1). Sunshield:
It prevents direct sunlight.
2). Audio|Sensor|Alarm connection cables:
Cables to connect audio input(microphone), audio output(speaker), digital input(sensor), and digital
output(alarm). Refer to Section 5.5: Connections for more information.
3). LAN connector:
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
4). Power adaptor connector:
Connect the provided DC12V adaptor for power supply.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
55
Installation and User Manual| VISIX V-Series All-in-One Cameras
5.4 Installation
INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET
Installation Template
Ø2.72 in. (69 mm)
3 - Ø0.26 in. (6.5 mm)
CAUTION:
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template paper can be found inside the package separately.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
56
Installation and User Manual| VISIX V-Series All-in-One Cameras
Screw &
Plastic Anchor-3pcs
Steps:
1).
on Guide
Drill three holes on the installation surface based on the provided installation template.
2).
Insert the plastic anchors into the holes.
3).
Install the provided ferrite core on the cable by referring to the NOTE: below.
4).
Attach the provided wall cushion to the bottom of the camera’s pan/tilt bracket.
5).
Fix the camera to the installation surface.
Installation Template
a.
Align the screw holes of the camera’s pan/tilt bracket and the plastic anchors.
b.
Insert the provided screws(M4X35) into the plastic anchors through the screw holes of the
camera’s pan/tilt bracket.
c.
Tighten the screws firmly into the plastic anchors.
CABEL CORE
6).
Connect all the necessary cables by referring to Section 5.5: Connections for more
information.
7).
Adjust the angle by referring to Adjust Angle of the Camera.
NOTE:
Use of Ferrite Core:
Installing the ferrite core to a LAN cable is highly recommended to reduce high frequency noise level.
Please follow the instructions below:
Steps:
1).
Open the ferrite core by lifting the clip.
2).
Make one loop with the cable through the ferrite core.
3).
Close the ferrite core to hold the cable loop into its place.
ETHERNET
WIRE
CAUTION:
Sealing gaps is recommended as gaps may appear after the camera installation. Gaps may cause
problems such as moisture, water leakage and etc., which negatively affect the operation of the camera
if gaps remain unsealed.
CAUTION:
To prevent products from damage, place the camera on a stable and non-vibrating surface. If the
stability is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
ETHERNET
57
Installation and User Manual| VISIX V-Series All-in-One Cameras
ADJUSTING ANGLE OF THE CAMERA
❶
❷
Steps:
1).
Loosen the set screw located on the right side of the camera’s bracket by using the provided
Torx (T20 M4x23) wrench. Once the set screw is loosened, you can move the tilting joint and
the panning joint of the camera respectively.
2).
Adjust the angle by moving the tilting joint and the panning joint.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
58
Reset
Anchor-3pcs
SW
1
Installation and User Manual| VISIX V-Series All-in-One Cameras
SW
3
SW
2
5.5 Connections
SW
6
SW
5
SW
4
on Template
BLACK
BROWN
RED
ORANGE
❷SENSOR
YELLOW
GREEN
ALARM 1 BLUE
❸ ALARM 2
VILOET
GRAY
❶AUDIO
AUD IN
AUD GND
AUD OUT
DI
DI COM
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
❺ Power adaptor
connector
❹LAN
connector
1). Audio connection
SW2provides a mono
SW3audio input and output. Due to low audio output power, an amplified
The camera
speakerNis /recommended
enhanced sound (Refrain from connecting a headphone or an
A
Nfor/ A
earphone directly to the camera).
SW1
SW5
SW6
N/A
N/A

Microphone In: Max 2Vp-p, 20KΩ (90dB)

Headphone Out: 60mW, 16Ω (95dB)
VIDEO DO
Out
DI
C 1 C 1
AUDIO
Out
In
ETHERNET
MICRO SD
Amp Speaker
Mic
2). Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the following
figures. Settings can be done through the camera’s webpage.

Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
CAUTION:
Do not exceed the maximum input voltage or relay rate.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
59
DC
Installation and User Manual| VISIX V-Series All-in-One Cameras
+3.3V
Internal
Internal
DI
Output of
Sensor
+
DI
-
COM
COM
Relay Type
Output of
Sensor
+
-
-
+
Voltage Type
3). Alarm (DO1 | DO2) connection:
Only the relay type is supported.

Digital Output 1

Relay Rating: Max 30VDC 1A

Normally Open (N.O) at power off

Digital Output 2

Relay Rating: Max 30VDC 1A

Normally Closed (N.C) at power off
CAUTION:
Do not exceed the maximum relay rating.
4). LAN connection:
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to connect
the device to a hub or a router in the network. Refer to Section 6: Power over Ethernet for more
information.
5). Power Connection:
The camera can be powered by either 12VDC or PoE. If the camera is powered via PoE, you do not
need to connect the power adaptor. For more information about PoE, refer to Section 6: Power over
Ethernet for more information.
NOTE:
Operation of the internal heater:

Temperature criterion for the heater operation: 0˚C (32˚F)

Lowest temperature to guarantee the heater operation during the device operation: -40˚C (-40˚F)

Lowest temperature to boot up the device when the device is powered on:

0˚C (32˚F)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
60
Installation and User Manual| VISIX V-Series All-in-One Cameras
5.6 Full Camera Specifications
Camera Module
Array Size
206x156
Detection Type
Uncooled vanadium oxide microbolometer
Sensor pixel size
12um
Spectral Response
7.8 ~ 14
Lens
4mm, F1.2 (FOV:36o)
Sensitivity
Less than 100mK
Video
Compression Format
H.264 and MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
4:3 Mode
QVGA(320x240), VGA(640x480), NTSC(720x480), PAL(720x576), SVGA(800x600)
16:9 Mode
320x180, 480x270, 640x360, 800x450, 960x540, 1120x630, 1280x720
Frame Rate
Max. 9FPS in all resolutions
Motion Detection
Built-in
Burnt-in Text (Digital)
Time stamp and text caption overlay
Analogue Output
-
Audio
Input/output
1/1 channel
Compression Format
G.711
Function
Digital Input/output
1/2 channel
RS-485
-
Network
10/100 Base-T
Power over Ethernet
(PoE)
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv2c/v3(MIB-II),
IGMP, ICMP, SSLv2/v3, TLSv1, SRTP, RTMP
Storage
1 x microSDHC card embedded
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
61
Installation and User Manual| VISIX V-Series All-in-One Cameras
5.7 Camera Dimensions
2.40 in. (61 mm)
2.28 in.
(58 mm)
2.72 in.
(69 mm)
2.99 in. (76 mm)
8.17 in. (207.5 mm)
7.5 in. (190.5 mm)
3.15 in. (80 mm)
6.75 in. (171.5 mm)
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
62
Installation and User Manual| VISIX V-Series All-in-One Cameras
6 Power over Ethernet Specifications
The Power over Ethernet (PoE) is designed to extract power from a conventional twisted pair Category 5
Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.
IEEE 802.3af allows for two power options for Category 5 cables.
The IEEE 802.3af-2003 standard allows up to 15.4 W of power the device. However, 12.95W is the
available power, as some power gets lost in the cable. The updated IEEE 802.3at-2009 (PoE+) standard
allows up to 25.5 W (Max 34.2 W) of power the device.
PoE has advantages over conventional power in such places where AC powers cannot be reached or is
expensive to wire.
6.1 Power Comparison
Property
802.3af
802.3at
Available Power
12.95 W
25.50 W
Max. Power by PSE
15.40 W
34.20 W
Max. Current
350 mA
600 mA
Supported Cable
Category 3 or higher
Category 5 or higher
NOTE:
For proper activation of PoE, the Category 5 cable must be shorter than 100m and conform the PoE
standard.
NOTE:
With non-Power Sourcing Equipment (non-PSE):
When it is connected with non PSE, the power adaptor should be connected.
With power adaptor:
Connecting both PSE and power adaptor does not do any harm to the product. Disconnecting PSE or
power adaptor from device does not reboot the device as long as either one is connected to the device.
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
63
Installation and User Manual| VISIX V-Series All-in-One Cameras
7 Revision History
Man #
Date (mm/dd/yyyy)
Comments
11-2015-1
11/19/2015
Styled
01-2016-22
01/22/2016
Finalized first draft
10225 Westmoor Drive, Suite 300, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC
64