Quattro inverter / charger

5kVA 120V Lithium Ion battery compatible

Quattro

24/5000/120-100/100 www.victronenergy.com

Two AC inputs with integrated transfer switch

The Quattro can be connected to two independent AC sources, for example shore-side power and a generator, or two generators. The Quattro will automatically connect to the active source.

Two AC Outputs

The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than

20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.

Virtually unlimited power thanks to parallel operation

Up to 10 Quattro units can operate in parallel. Ten units 48/5000/70, for example, will provide 45kW / 50kVA output power and 700 Amps charging capacity.

Three phase capability

Three units can be configured for three-phase output. But that’s not all: up to 10 sets of three units can be parallel connected to provide 135kW / 150kVA inverter power and more than 2000A charging capacity.

PowerControl – Dealing with limited generator, shore-side or grid power

The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (Up to 40A per 5kVA Quattro at 120VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting shore or generator power

This feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Solar energy: AC power available even during a grid failure

The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.

System configuring has never been easier

After installation, the Quattro is ready to go.

If settings have to be changed, this can be done in a matter of minutes with a new DIP switch setting procedure.

Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed!

Alternatively, VE.Net can be used instead of the DIP switches.

And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

Quattro

PowerControl / PowerAssist

Integrated Transfer switch

AC inputs (2x)

Maximum feed through current (A)

Input voltage range (V DC)

Output (1)

Cont. output power at 25 °C (VA) (3)

Cont. output power at 25 °C (W)

Cont. output power at 40 °C (W)

Peak power (W)

Maximum efficiency (%)

Zero-load power (W)

Zero load power in AES mode (W)

Zero load power in Search mode (W)

Charge voltage 'absorption' (V DC)

Charge voltage 'float' (V DC)

Storage mode (V DC)

Charge current house battery (A) (4)

Charge current starter battery (A)

Battery temperature sensor

Auxiliary output (A)

Programmable relay

Protection

VE.Bus communication port

General purpose com. port (7)

Common Characteristics

Common Characteristics

Battery-connection

230 V AC-connection

Weight (kg)

Dimensions (hxwxd)

Safety

(2)

Emission, Immunity

(5)

(6)

1) Can be adjusted to 50 Hz

2) Protection key: a) output short circuit b) overload c) battery voltage too high

3) Non linear load, crest factor 3:1

4) At 25 ˚C ambient

24/5000/120-100/100 120V 48/5000/70-100/100 120V

Input voltage range: 90-140 VAC Input frequency: 45 – 65 Hz Power factor: 1

2x100

INVERTER

Yes

Yes

19 – 33 37,2 – 64,4

Output voltage: 120 VAC ± 2% Frequency: 60 Hz ± 0,1%

5000

4500

4000

10000

94

25

20

5

94

25

20

6

CHARGER

28,8

27,6

52,826,4

120

4

57,6

55,2

52,8

70 n. a.

Yes

GENERAL

Max. load: 50A Switches off when in inverter mode

Yes, 3x a-g

For parallel and three phase operation, remote monitoring and system integration

Yes, 2x

Operating temp.: -20 to +50 ˚C Humidity (non condensing): max. 95%

ENCLOSURE

Material & Colour: aluminium (blue RAL 5012) Protection category: IP 21

Four M8 bolts (2 plus and 2 minus connections)

M6 bolts

66 lb 30 kg

17,5 x 13,0 x 9,6 inch 444 x 328 x 240 mm

STANDARDS

EN 60335-1, EN 60335-2-29

EN55014-1, EN 55014-2, EN 61000-3-3 d) battery voltage too low e) temperature too high f) 120 VAC on inverter output g) input voltage ripple too high

5) Switches off when no external AC source available

6) Programmable relay that can be set for general alarm, DC undervoltage or genset start/stop function

AC rating: 120V/4A

DC rating: 4A up to 35VDC, 1A up to 60VDC

7) A. o. to communicate with a Lithium Ion battery BMS

Digital Multi Control

This panel is intended both for

MultiPlus and Quattro units.

Allows PowerControl and

PowerAssist current limit setting for two AC sources: a generator and shore-side current for example.

Setting range: up to 200 Amps.

The brightness of the LEDs is automatically reduced during night time.

Computer controlled operation and monitoring

Several interfaces are available:

- MK2.2 VE.Bus to RS232 converter

Connects to the RS232 port of a computer (see ‘A guide to VEConfigure’)

- MK2-USB VE.Bus to USB converter

Connects to a USB port (see ‘A guide to VEConfigure’)

- VE.Net to VE.Bus converter

Interface to VE.Net (see VE.Net documentation)

- VE.Bus to E-PLEX converter

Interface to the E-PLEX System. The world’s most advanced and field

proven digital switching and monitoring system.

- Victron Global Remote

The Global Remote is a modem which sends alarms, warnings and system status

reports to cellular phones via text messages (SMS). It can also log data from

Victron Battery Monitors, Multi’s, Quattro’s and Inverters to a website through a

GPRS connection. Access to this website is free of charge.

BMV-600 Battery Monitor

The BMV–600 Battery Monitor features an advanced microprocessor control system combined with high resolution measuring systems for battery voltage and charge/discharge current. Besides this, the software includes complex calculation algorithms, like Peukert’s formula, to exactly determine the state of charge of the battery.

The BMV–600 selectively displays battery voltage, current, consumed Ah or time to go.

The monitor also stores a host of data regarding performance and use of the battery.

Several models available (see battery monitor documentation).

Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands

General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40

E-mail: [email protected] | www.victronenergy.com