advertisement
Flush-Mount Low-Profile
UFO Camera
Manual
Model
EV-122C-FVB3Q
EV-6640-N3WQ
EV-122C-PVB3Q
EV-6640-P3WQ
Small size - only 3” diameter
1 /
3
” Sony Super HAD II CCD
3.7mm Pinhole lens
Low 0.05 Lux rating
Video Output
NTSC
NTSC
Resolution
480 TV Lines
600 TV Lines
PAL
PAL
480 TV Lines
600 TV Lines
Lens rotates to nearly any angle
Low-profile design blends into nearly any décor
Vandal-resistant metal housing
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
ENFORCER Flush-Mount Low-Profile UFO Camera
Specifications:
NTSC
PAL
Type
Image sensor
Resolution
Lens
Pickup elements
Sync
Video output
NTSC
PAL
Minimum illumination
S/N ratio
Shutter control
Gain control
White balance
Gamma correction
Operating voltage
Current draw
Operating temperature
EV-122C-FVB3Q
EV-122C-PVB3Q
Flush-Mount Low-Profile UFO Camera
1 /
3
” Sony Super HAD II CCD
480 TVL 600 TVL
3.7mm
EV-6640-N3WQ
EV-6640-P3WQ
510x492 pixels
500x528 pixels
768x494 pixels
752x582 pixels
Internal
1.0Vp-p composite video, 75Ω
0.05-lux
>48dB
Auto Electric Shutter (AES), 1/60~1/100,00 s
Auto
Auto
0.45
12VDC ±10%
130mA ±10mA
-4°~122° F (-20°~50° C)
Parts List:
1 x Camera
1 x Flange
1 x Base
1 x Ring bracket
3 x Mounting screws
1 x Manual
1 x DC Plug with
terminal block
Dimensions:
2 SECO-LARM U.S.A., Inc.
Overview:
Camera ball
Flange
ENFORCER Flush-Mount Low-Profile UFO Camera
Screw
(1 Shown, 3 included)
Base Ring bracket
(inside the ceiling wa l)
Female BNC connector
DC Plug with terminal block
DC Jack
Flange Base Ring bracket
Before Starting:
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera where it is exposed to rain or other moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
6. Do not drop the camera or subject it to strong vibrations
Installation:
1. Run a 12VDC power supply wire and a video cable with a male BNC connector to the wall or ceiling where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC power supply.
3. Temporarily connect the camera’s female BNC connector to the video cable’s male BNC connector.
4. While watching the monitor, hold the camera against the wall or ceiling by hand where it is to be mounted, then turn the camera until it is certain that this mounting location is correct. Use a pencil to mark the location.
5. Disconnect the 12VDC power supply and video cable.
6. Drill a 2 1 /
4
” (56m) hole in the ceiling or wall where the camera is to be mounted.
7. Twist the flange off the base and remove the camera ball.
8. Place the ring bracket behind the hole.
Note: Ring bracket is not necessary if mounting directly to wall.
9. Push the base into the hole, and secure to the ring bracket using the three supplied marking screws.
10. Run the power supply and video cable through the wall or ceiling to the hole, and through the bracket and base. Connect to the camera’s power and video connectors.
11. Hold the ball in the base, and secure with the flange.
Do not tighten securely.
12. Apply the power to the camera. Watch the monitor and adjust the angle of the lens.
13. Secure the camera by tightening the flange.
14. Do a final test of the video camera and monitor.
SECO-LARM U.S.A., Inc. 3
ENFORCER Flush-Mount Low-Profile UFO Camera
Troubleshooting:
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the monitor is connected properly.
The screen image is dim
The screen image has poor contrast.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of three (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
SECO-LARM
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
Website: www.seco-larm.com
E-mail: [email protected]
PICSN4
M UFO_Camera_1206.docx
4 SECO-LARM U.S.A., Inc.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement