Bluetooth Fitness Armband
User's Manual
DENVER BFA-10
ALL RIGHTS RESERVED.COPYRIGHT DENVER ELECTRONICS A/S.
www.denver-electronics.com
DENVER BFA-10
Smart Bracelet User Manual - English
[Compatibility]
The Smart Wristband only supports the following selected mobile devices:
IOS: OS must be IOS7.0 or later, Bluetooth 4.0; Such as: iPhone 4S, 5, iPod touch5,
etc.
Android: OS must be Android4.3 or later, Bluetooth 4.0; Such as: Samsung S4, Note3,
etc.
[Function Icon]
Time: 00:00
Steps:
Sleep monitor:
Move Alert:
Bluetooth:
Autodyne:
Distance:
’
Calories:
Call ID Display:
Alarm clock:
Message Push:
Bluetooth broadcast:
[Quick Start Guide]
1. You should charge the bracelet for 30mins before using it. Pull out the host as shown
below, Insert the host to a 5V/1A USB port for charging. The red indicating light stops
flashing when it is full charged for 30 minutes.
ENG-1
2. Install APP: Go to App store or play store, download this APP: “DENVER BFA-10”
and install it. To use DENVER BFA-10 APP, make sure your mobile device
connected with internet via Wi-Fi or 3G.
3. Account set-up: Open the “DENVER BFA-10” App. Log in if you have an account, or
register a new account.
4. Pairing
Keep your phone with
Bluetooth and WIFI “on” for this
step. Log in the App DENEVR
BFA-10, and the system shows
the main page. Tap the left
corner button or slide the
screen from left to right, and
click [Device Connection]
Double press the button on the
bracelet, the radar icon “ ”shows
up on the bracelet, tap the button
[Searching device] on APP, select
your right ID from the device list,
and wait for 1-2 seconds
ENG-2
Android device will pop up
[Device pair request], choose
“confirm”, and finish pairing.
IOS device will pop up [Pair
Device Success], [Bluetooth
Pairing Request], click “pair”,
and finish paring.
If the pop-up do not appear within 1 minute, repeat the above steps.
5. SYNC Data
The bracelet SYNC data automatically after connected with phone by APP (DENVER
BFA-10), the bracelet time will be calibrated same as the time of phone. SYNC data
includes: steps, calorie, distance. You can check out if the data SYNC is completed
successfully on the APP. First SYNC data takes 1-2 minutes. SYNC data can be done
manually by clicking the refresh button on APP.
6. Mobile discovery
Press the button on the bracelet until it vibrates once, the phone will ring
7. Sleep monitor
ENG-3
Turn on Sleep Mode: Press the button on the bracelet until it vibrates twice, the bracelet
start sleep monitor mode, the icon
shows up. To exit the sleep mode: Press the
button on the bracelet until it vibrates twice, the bracelet exits the sleep monitor mode,
the bracelet back to time display.
8. Restart the bracelet
Press the button on the bracelet until it vibrates 3 times. Then the screen is shut off，
white light glitters once, and the bracelet is restarted. A restart will not delete the
recorded data.
9. Button Function
Keep the device be light
Long pressing, after shaking two times, the device be going on sleeping monitor
Long pressing, after shaking three times, the device be going on restart
10. For more functions, please download APP “DENVER BFA-10” to use.
[FAQ]
1. The bracelet cannot exit the sleep mode by pressing the button? - To restart the
bracelet can exit the sleep model successfully.
2. When connected with App, the data SYNC is finished but the bracelet time display is
still incorrect? - Restart the bracelet and try data SYNC again
3. Why my bracelet has no call ID display? - Android Phone: After being connected with
bracelet with APP, please allow “DENVER BFA-10” to visit calls, SMS, contacts and
ENG-4
keep “DENVER BFA-10” running in background. If there are security software on
your phone, set up the software “DENVER BFA-10” as “trust”.
IOS: If no call ID display, please restart your mobile and connect the bracelet again.
When it is connected, please wait until the phone pops up “Bluetooth pairing request”
and click “pair”, then the call ID display function comes.
4. The bracelet icon shows the Bluetooth was connected, but the APP cannot SYNC
data? - Generally it is caused by the Bluetooth of the phone. Please switch off the
APP firstly, restart the Bluetooth and repair. If the above step does not work, please
restart your phone and try again.
5. Why my bracelet lose connection with my phone frequently? - Please check if your
phone or other security software sets “DENVER BFA-10” as trusted APP or not. If
not, please set it as trusted and try again.
6. Is my bracelet water-proof? - No. Please don’t wear it when in shower or when
swimming.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
ENG-5
Electric and electronic equipment and included batteries contains materials,
components and substances that can be hazardous to your health and the environment,
if the waste material (discarded electric and electronic equipment and batteries) is not
handled correctly.
Electric and electronic equipment and batteries is marked with the crossed out trash
can symbol, seen below. This symbol signifies that electric and electronic equipment
and batteries should not be disposed of with other household waste, but should be
disposed of separately.
As the end user it is important that you submit your used batteries to the approriate and
designated facility. In this manner you make sure that the batteries are recycled in
accordance with legislature and will not harm the environment.
All cities have established collection points, where electric and electronic equipment
and batteries can either be submitted free of charge at recycling stations and other
collection sites, or be collected from the households. Additional information is available
at the technical department of your city.
Hereby, Inter Sales A/S, declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A copy of the
Declaration of conformity may be obtained at: Inter Sales A/S, Stavneagervej 22,
ENG-6
DK-8250 Egaa, Denmark.
Imported by:
DENVER ELECTRONICS A/S
Stavneagervej 22
DK-8250 Egaa
Denmark
www.facebook.com/denverelectronics
ENG-7
">
