LaserPro VENUS Laser Engraver User Manual

PDF

Documento

Anúncio

USER MANUAL

VENUS

Content

UNPACKING

............................................................................................................................................. 3

Unpacking inspection

............................................................................................................................... 3

QUICK MENU

.......................................................................................................................................... 4

LENS and MANUAL FOCUS GAUGE

............................................................................................. 5

I. INTRODUCTION

.............................................................................................................................. 6

Principles of CO

Laser

............................................................................................................................ 6

Safety

............................................................................................................................................................ 6

Precaution

.................................................................................................................................................... 6

Fire Precaution

........................................................................................................................................... 7

Warning Label

............................................................................................................................................ 8

Frequently Asked Questions

................................................................................................................. 10

II. RECOMMENDED CONFIGURATION

....................................................................... 3

III. HARDWARE INSTALLATION

....................................................................................... 4

Cabling Connection:

................................................................................................................................. 4

Parallel Transmission

................................................................................................................................ 5

Serial Transmission

................................................................................................................................... 5

Interface for Macintosh

............................................................................................................................ 5

Exhaust Ventilation

................................................................................................................................... 5

IV. SOFTWARE INSTALLATION

......................................................................................... 6

Install LaserPro VENUS printer driver for windows 9x /XP

......................................................... 6

V. OPERATION

....................................................................................................................................... 7

Environment

................................................................................................................................................ 7

Flexible Utility of Your Memory Buffer.

............................................................................................ 7

Start to Operate

........................................................................................................................................... 9

Control Panel Operation

........................................................................................................................ 10

START/STOP....................................................................................................................................... 10

ENTER ................................................................................................................................................. 11

AUTO FOCUS ..................................................................................................................................... 11

Arrow Keys .......................................................................................................................................... 12

ESC (Escape) ........................................................................................................................................ 12

NEXT FILE .......................................................................................................................................... 12

RED BEAM.......................................................................................................................................... 13

SPEED.................................................................................................................................................. 13

POWER ................................................................................................................................................ 13

PAUSE ................................................................................................................................................. 13

RESUME.............................................................................................................................................. 13

DEL FILE............................................................................................................................................. 13

FUNCTION.......................................................................................................................................... 14

Software Operation

................................................................................................................................. 27

Mode:.................................................................................................................................................... 27

Parameter Settings ................................................................................................................................ 33

Paper ..................................................................................................................................................... 36

Advanced Function............................................................................................................................... 36

VI. BASIC MAINTENANCE

...................................................................................................... 38

Clean the mirror -

..................................................................................................................................... 38

Clean the focus lens –

............................................................................................................................. 40

VII. TROUBLE SHOOTING

....................................................................................................... 41

Quality Problems

..................................................................................................................................... 41

Non-operational Problems

..................................................................................................................... 41

Laser beam does not generate............................................................................................................... 41

APPENDIX I. Specification

.......................................................................................................... 42

APPENDIX II. 3D Function

..................................................................................................... 43

Tip for 3D Application

........................................................................................................................... 43

UNPACKING

Caution:

l The weight of LaserPro VENUS is about 32 kg (70 ponds). l Please save the original shipping carton in case any returning service is needed. l Please inspect what you have received from the shipped carton by comparing with the following listed items.

Unpacking inspection

Your package should contain the following items:

ITEM

Cleaning Set

cotton swab

lens cleaner

lens tissue (lint free)

QUANTITY

1 pack

1.5” Manual Focus Gauge (blue color)

AC Power Cord

Print Port Cable

LaserPro VENUS Driver

Mirror (for Mirror#2, #3)

Engraving Samples 1 pack

QUICK MENU

1. Connect air exhaust system.

2. Setup computer and connect with engraving system properly.

3. Turn ON host computer system.

4. Install the Venus Driver. (for the first time use only)

5. Use Windows-based program (such as CorelDRAW, PhotoShop, PhotoPaint, Illustrator, CASmate,

Signlab, EasySign, AutoCAD, etc.) to operate with the engraver.

6. Turn ON engraver. The working table moves down 50mm approximately and the lens carriage moves to the home position (upper left corner) after system initialization.

7. Auto-focusing: under STOP status, put work-piece on the table, move X-axis (Please refer to Fig. 3) and carriage by arrow keys to locate the lens carriage above the engraving material (holding carriage by hands for prompt moving is acceptable under STOP condition but not recommended). Press

AUTO FOCUS the table will move up then down to the focal position automatically.

8. The following is an example by using CorelDRAW V.8.0.or after

Layout Page Setup Set from Printer, choose Portrait

OK Edit desired file (picture etc.) File Print Properties

Options, choose desired Mode (refer to Fig. 8) then set up proper resolution, power and speed

OK Print

File name is shown on LCD then press START/STOP button.

(Please refer to page 14, Start to Operate, for detail operation in different mode selection)

NOTICE:

1.When operating with CorelDRAW V.8.0 or after, please choose Landscape

for Page Setup when X > Y ; choose Portrait when X < Y O.K..

2. When using the available artworks from the Clipart of CorelDRAW, to prevent

the hidden vector lines shown on your engravings. Please do as follows:

CorelDRAW, choose file from Clipart Bitmaps Convert to

Bitmap Click Color then choose Grayscale Ok

3.In order to ma tch Venus driver’s color. Make sure your CorelDRAW V.8.0 or

after the ‘Calibrate colors for display ‘ is disable. Please follow the steps:

Tools Options Global

Disable ‘Calibrate colors for display ‘

NOTE:

Color Management

OK. l If the memory buffer is set up in Single file mode, under START condition, the engraver will start to engrave/cut upon receiving a file. While if the memory buffer is set up in

Multiple File mode, receiving at least one complete file then press START/STOP to start a job (refer to page 14, Start to Operate).

l Choices of DPI must be the same for both editing and printing out a file. l Turn on the air exhausting system before engraving. l The maximum loading weight of working table is 5 kg. l When engraving at 3D mode or cutting materials that easily caught on fire, such as acrylic, wood or paper, it is advised to have air compressor turned on to prevent flame.

LENS and MANUAL FOCUS GAUGE

Focal Length Matched Color

LENS MANUAL FOCUS GAUGE

1.5” Standard Purple Blue (same as 2.0”)

2.0” Option Blue Blue

2.5” Option Gold Gold

Manual Focus Gauge

Insert to the hole of the holder for manual focusing

Mirror

Manual Focus

Gauge Holder

NOZZLE

Focus Carriage Assembly

Lens 2.0, 2.5

Slot position for

Lens 1.5 only

Auto Focus Gauge

Focal-Sharp™

I. INTRODUCTION

Principles of CO

Laser

LASER

is a

L

ight

A

mplification by

S

timulated

E

mission of

R

adiation. A CO

laser works by exciting the molecules of a carbon dioxide gas mixture. To engrave, the beam is focused through a lens. The intensive beam can vaporize the surface of the material leaving an engraved image or, in some cases, cutting through the material.

Safety

The safety rating of Class 1 by CDRH means that the laser beam is enclosed in a cabinet and has safety interlock mechanisms to protect the operator from injury. While when a class 1 laser system equipped with a red dot pointer which allows you to position laser beam, the safety rating turns into Class 3a due to the red beam is laser light. A few extra safety precautions; namely, avoid placing your eyes in the red beam path, is required.

Precaution

1. Do not attempt to modify or disassemble the laser system at any time.

2.Always wear appropriate safety goggles during operation, especially when engraving with mirrors or coated metals such as enameled brass and anodized aluminum..

NOTE: Each LaserPro laser machine is equipped with a safety goggle, if you need another one, please contact LaserPro for it or try to get one that meets the following specification.

190-398 nm OD5+

10,600 nm OD5+

Visible light transmission: 92.9%

3.Good ventilation is required to remove odors and vaporized materials to the outside of the building or structure. An exhausted system is recommended.

4.Invisible intensive laser radiation may cause physical burns or sever eye damage. Always read the manual and caution labels carefully before operation.

5.Do not work with reflective metals, heat sensitive surfaces or other materials that may produce toxic substances, such as PVC and Teflon.

6.A fire extinguisher should be available on hand at any time.

7.Never leave the machine unattended during operation.

8.Follow the recommendations for maintaining and cleaning your system. Not only will this enable you to engrave efficiently, it will ensure that your machine runs safely as well.

Fire Precaution

1.When engraving at 3D mode or cutting materials that easily caught on fire, such as acrylic, wood or paper, it is advised to have air compressor turned on to prevent flame.

2.If cutting table, or honey comb table, is used for cutting purpose, do not leave any material underneath, as when material at top is cut through, the material at below will be burned easily due to trapped heat.

3.It is not encouraged leaving the cutting job unattended, especially with materials mentioned above.

Warning Label

DANGER

INVISIBLE LASER RADIATION WHEN OPEN

AND INTERLOCK FAILED OR DEFEATED

AVOID EYE OR SKIN EXPOSURE DIRECT

OR SCATTERED RADIATION

On the back right side of the top area.

WARNING!!

Do not use reflective metals, heat sensitive surfaces or other materials that may produce toxic substances, such as PVC and Teflon.

Any corrosion caused by working on an unsuitable substances will not be covered in the warranty.

On the upper center of the top area.

CAUTION

AVOID PLACING YOUR EYES IN

THE RED BEAM PATH

On the front center of the top door.

On the surface of Focus Carriage

Frequently Asked Questions

1. What materials can be processed by CO

laser?

Virtually any materials such as acrylic, wood, fabrics, glass, leather, marble, stone, rubber stamps, paper products, coated metals, plastics (especially micro plastic developed by IPI, Spectrum and Rowmark etc.) other hard-surface materials blended with polyester and fibers ( Corian™ , Fountainhead™ , and Avonite™ etc.) or laserable simulated products of stone, wood and metal etc.

Bare metals can not get a good engraving result by using CO

laser. However, special kind of spray has been developed that allows CO

laser to mark on the bare metals such as stainless steel, aluminum etc. Do not engrave or cut materials which are heat sensitive or toxic substances can be produced ( e.g. PVC and

Teflon coating ).

2. What is the life cycle of the laser source?

The life cycle of laser source is around 20,000 hours, however it can be re- filled and should be done by your dealer.

3. What is the main purpose of air assist system?

The air assist system can provide a much better engraving & cutting effect, as it will blow away vaporized particles and prevent fire due to overheating.

4. What does cutting table do?

The cutting table, also known as honeycomb table, is especially useful for vector cutting application. The space between materials and working table, gapped by cutting table, allows heat and smoke to be disbursed and vented out which may otherwise cause bad cutting effect.

5. What is the maximum engraving speed of LaserPro Venus?

The maximum engraving speed of LasePro Venus is 508 mm/sec (20 inch/sec).

Top Door

Power on/ off

Switch

Control Panel

Fuse &

Ports

Laser source inside

Air Flow

Adjuster

Back View

Air Flow

Fixer

Turn clockwise to decrease the air flow and counterclockwise to

Press the ring to pull out the air tube.

Air inlet connect to air compressor

NOTE: Please refer to Chapter VI and follow the

instruction for the basic maintenance of mirror.

Step

3 Step 2

Step 1

Disassemble to maintain

#1 mirror.

Please refer to the right layout.

Unscrew and pull out

#1 mirror carefully without touching the surface of the mirror.

Unscrew and

remove the dust prevention box.

Unscrew and remove the panel.

Dust Prevention

Window

#3 Mirror & Holder

Release the Screw to

Pull Out the Mirror

Motion System I

Dust Prevention Box (#2 Mirror inside)

Y-axis

Motor

X-axis

Air Flow Adjuster

Bearing Track

Manual Focus

Gauge Holder

Focal-Sharp™

Auto-focus

Y-axis

X-axis Motor

Choose air exhausting direction either from back of the table or through the holes on working table. Adjuster in middle position can exhaust air both backward and downward.

Release the Screw to

Low down the plate

Dust Collecting

Plate

Hole

Plug

Motion System II

Dust Partition

The diameter of the object in this circle must be less than 45 mm

II. RECOMMENDED CONFIGURATION

Computer

Your PC must be sufficient to equip with Window 95 at least.

We recommend the specification of PC for better work as

below:

CPU

DRAM

Pentium at least

32 MB RAM or up

FDD

HDD

One 3.5" 1.44 MB floppy

1.2 GB Hard Drive or up

SVGA 15" Super VGA Monitor

★ ★On Board Parallel Mode(Setup from PC BIOS):

SPP— Preferred Mode

ECP— Cable length less than 1.8meters

Scanner

Flat Bed

Minimum resolution: 200 DPI

Software

GCC driver (designed under Window 95 or higher level)

Windows Window 95 or higher

CorelDRAW 7.0 Version or up

Any program that can output HPGL commands

III. HARDWARE INSTALLATION

Caution:

15AMP resetable fuse

l Turn all equipment off before making any connection. l Check the plug of the power cord to see if it matches the wall outlet. If not, please contact your dealer.

Cabling Connection:

1. Insert the power cord (male) into a well grounded power outlet.

2. Plug the other end (female) into the engraver. The engraver has been designed to

switch from 100~240 VAC automatically.

3. The engraver can communicate with a computer through either a serial (RS-232C) or a parallel port

(Centronics).

Power on/off

Switch

3AMP resetable fuse

AC Power

Connector

Serial Interface

Connector

Parallel Transmission

Connect a parallel cable to the engraver (parallel port) then to the parallel port of the host computer.

Caution:

Never use a mechanical switch box when a second printer port is required.

The electrical surges can cause damage to the computer and the engraver.

Serial Transmission

If you are using IBM PC, PS/2 or their compatibles, connect the supplied RS-232C cable to the engraver

(serial port) then to the serial port of the host computer.

Interface for Macintosh

To operate the engraver with a Macintosh computer (e.g. Power Mac), you

need a MAC modem cable (DIN8 to DB25) as an adaptor to connect to the RS-232C cable.

Exhaust Ventilation

2 or 4 inch diameter flexible hose

Seal

Clip

IV. SOFTWARE INSTALLATION

Install LaserPro VENUS printer driver for windows 9x /XP

Power On, click

START

→ choose

Settings

and click

Printers

→ Double click

Add printer

and start

Add printer wizard

→

Next step

→ Choose

Local

and click

Next step

→ choose

Have disk

and click

Next step

→ Insert the VENUS Driver disk properly into the floppy drive then click

OK

→ choose the port where your laser system is connected and click

Next step

→ name your system or bypass

→ choose the driver to be default printer

→

Next step

→ select

No

when asked to print a test page and click

Finish

Now the LaserPro VENUS printer driver is installed completely. Don't forget to take the GCC driver disk from the floppy drive and store in a safe place.

V. OPERATION

Environment

l A clean, well-ventilated room with a temperature of 15℃~ 25℃ (60℉~78℉) (Strongly suggested the temperature of 25℃) and a relative humidity between 30% and 40%, as an office type environment. l Stable floor isolated from vibration. l Avoid from unstable voltage supply. l Short path for an effective air exhaust. l Have a fire extinguisher available at any time.

Flexible Utility of Your Memory Buffer.

The standard memory buffer size of Venus is 16M and can be expanded to 64 M (32M SIMM x 2). You can choose Multiple file mode with limited memory to save files and re-call them for constant applications. Or, you can choose Single file mode to get an unlimited data output while still keep files that you saved before under multiple file conditions. However, the file sent under Single file mode will not be saved. In other words, every time you want to engrave this file, you have to re-send again from the host computer

Am I in Multiple File mo de or Single File mode now?

Power ON

Single / 1 File

OK: ENTER

Change: OR

NOTE:

LaserPro VENUS

Firmware VX.X

Copyrithg 200X

Initializing

Please Wait

Set memory buffer?

Yes: ENTER

End operation : Esc

Z init /AF position

Multiple /100 Files **

OK: ENTER

Change: OR

Table moves down about

50mm. Press FUNCTION key

Single / No Repeat

OK: ENTER

Change: OR

1. ** means default or current setting.

2. AUTO FOCUS and all other function keys should be operated under

STOP condition.

3. NEXT FILE and DELETE keys are invalid under Single file mode.

Start to Operate

Power ON

LaserPro VENUS

Firmware VX.X

Initializing

Please wait

Table moves down about 50mm automatically

Single file status

Under STARTcondition

Upon the receipt of files, start to engrave/cut

File:

Speed: %

Power: %

DPI:

Multiple file status

Under STOP

condition

Press START/STOP, turn to STOP condition

File:

Speed: % 00:00

Power: % STOP

DPI:

File: # x file name

Speed: xx.x % 00:00

Power: xx % PPI: xxxx

DPI: xxx xxx K

Send a new file from host computer then press

NEXT FILE to show the file name on LCD.

Press

START/STOP

to engrave/cut

Press

NEXT FILE

to get a desired file

Press

FUNCTION key for further setting selection

File: # x file name

Speed: xx.x % 00:00

Power: xx % PPI: xxxx

DPI: xxx xxx K

Control Panel Operation

START/STOP

l Single File Mode:

Turn on power, VENUS is under START condition and ready to receive a file. LCD shows as follows:

File:

Speed: %

Power: %

DPI:

Upon the receipt of a file, VENUS starts to engrave/cut immediately. When a job is done, LCD will show the working time such as 100s means 100 seconds.

File: file name

Speed: xx % 01:10

Power: xx % STOP

DPI: xxx condition AUTO FOCUS and all other function keys can be operated while NEXT FILE and DELETE

keys are invalid under Single file mode.

File: file name

Speed: % 00:00

Power: % STOP

DPI: l Multiple File Mode:

Turn on power, LaserPro is under STOP condition and all function keys can be operated. Laser engraver is ready to receive a file. LCD shows as follows.

File:

Speed: % 00:00

Power: % STOP

DPI:

Upon the receipt of a complete file, LCD will show the following message for instance. Then press

START/STOP key, the engraver start engraving or cutting.

File: # 1 file name

Speed: 70 % 00:00

Power: 40 % STOP

DPI: 500

If there is no file having been sent, the message will display as follows.

Wait until at least one complete file is

Received, then press START

NOTE:

Please refer to the flow chart of “Start to Operate”, page 14 .

ENTER

Accept and store the selection for setting up.

AUTO FOCUS

This key can only be operated under STOP condition. Press this key will move up the working table until the engraving object touches the tip of the focus tool, then the table will move down and stop in focus automatically.

Whenever you change a lens with different focal length, press Function key and go through the process of

“Select lens ” (refer to page 23). After changing the lens, press AUTO FOCUS key to save the new focal

length in memory. LCD will show as follows:

Focusing

Then do setup or send a file to start a job

0.0 mm

NOTE:

1. “0.0 mm” means the focus position is the Z-axis home position of the

Working table. Above this position the value is negative while below this position the value is positive.

2.Whenever the motion system or working table has ever been adjusted by a technical person, please press AUTO FOCUS key to get an initial position before going through the function of “Tune (Auto focusing)” to change the focal length.

NOTICE:

To stop the motion of auto focus, please press either UP or DOWN arrow key. If you press the key continuously, working table will move up or down correspondingly.

Arrow Keys

Move cursor on the display for selection or adjust the working table on Z position by pressing the arrow keys of UP and DOWN.

NOTE:

UP key – After initializing, press this key will move up the table. LCD displays:

Focusing

Then do setup or send a file to start a job

－X.X mm

During working time (i.e. Start condition), this message won’t be shown.

When Auto Focus is under process, press UP key will stop the motion of Auto Focus and change to

up movement.

DOWN key – Same as above function but the motion direction is opposite.

ESC (Escape)

Exit and back to the main menu.

NEXT FILE

This key is valid under Multiple file mode only. Press this key the LCD shows

File: # x file name

Speed: xx % 00:00

Power: xx % PPI: xxxx

DPI: xxx xxxxx k

The “k” message shows on the lower right corner expresses the k bytes memory that has been left over in the buffer.

File: # shows the current working file number. Press NEXT FILE each time will increase 1 (i.e. 1, 2,

3… 100) and recycle the counting. Once the buffer has received up to 100 files, the LCD shows:

More than 100 files are not allowed

Please delete some and send again

If a file received is out of memory, the LCD shows

Not a complete file due to out of memory

Please delete some and send again

RED BEAM

On/Off red beam

SPEED

Set up laser speed for desired effect. When working without using VENUS’s driver. Press FUNCTION key then select one of the sixteen setups then set up desired cutting speed. No matter you are using VENUS’s driver or not, you can press PAUSE key prior to change speed during cutting or engraving. Set up desired speed, press ENTER then press RESUME to start the job again.

POWER

Set up laser power for desired depth and effect. Other conditions are same as stated in SPEED.

PAUSE

Temporarily stop the job during cutting or engraving.

RESUME

Restart the job after pausing.

DEL FILE

This key (delete file) is valid under Multiple file mode only.

Delete current file?

Sure: Press again

No: Esc

Press DEL FILE again to delete the file and LCD shows

FUNCTION

l Set memory buffer?

Now deleting current file Please wait

Setting memory buffer in Single file mode when working with a large data file, or Multiple file mode (up to 100 files) that can be saved for constant engraving.

Under Single file mode, you can only output one job a time. Unlimited data can be transferred without saving in the buffer therefore once you want to repeat the job you have to re-send the file from the host computer.

Under Multiple file mode, you can engrave one job while transfer and design the next simultaneously until

100 files’ memories are all used up.

Press FUNCTION key

Set memory buffer?

Yes: ENTER

End operation: Esc

Press ENTER key

Multiple /100 Files **

Ok: ENTER

Change: or

Single /1File

Ok: ENTER

Single /No Repeat

Ok: ENTER

Change: or or

Change: or

l Z init/AF position?

Z init/AF position?

Yes: ENTER

End operation: Esc

Delete all files ?:

ENTER

To avoid focus carriage hitting the engraving object accidentally during initializing, working table will move down about 50mm automatically after power on the equipment. Whereas, if a rotary attachment has been installed, the working table will move down to the bottom of the engraver.

As long as you have not press AUTO FOCUS key, you can go into this function and move the working table back to the original position before initializing. Once the AUTO FOCUS key has been used, the last auto focus position has been saved in the memory. Therefore, you can move the table to the last auto focus position instead of the original Z position by using this function.

Z init/AF position?

Yes: ENTER

End operation: Esc

Delete all files? :

Table is moving to init or AF position

End operation: Esc

Delete all files? :

Delete all files?

Ok: ENTER

End operation: Esc

Select lens? :

ENTER

l Delete all files?

All files in the buffer will be deleted by using this function when setting under Multiple file mode.

This function is invalid under Single file mode. Once you stop or complete a job under Single File mode the file won’t be saved in the buffer.

Delete all files?

Ok: ENTER

End operation: Esc

Select lens? :

ENTER

Are you sure?

Sure: ENTER

No: Esc

ENTER

Select lens?

Yes: ENTER

End operation: Esc

Select unit? :

l Select lens?

There are four different lenses for use on the LaserPro VENUS as follows:

Focal Length Resolution Cutting capability

1.5” standard

2.0” optional

2.5” optional

High

Low

Thin

Thick

The longer the focal length, and the bigger the spot size. The higher resolution lens is designed for precision engraving, while the lower resolution lens is mostly applied for cutting due to its lower beam divergence which results in a straighter cut in thick materials. However, using higher resolution takes longer time for engraving. The large spot size of lower resolution lens can spreads the laser’s heat over a larger area, which helps minimize melting thus can be applied to engrave certain kinds of plastics.

Select lens?

Yes: ENTER

End operation: Esc

Select unit? :

1.5 inch (38.1mm)**

Ok: ENTER

Change: △ or ▽

x.x inch (xx.xmm)**

Ok: ENTER

Change: △ or ▽

Select unit?

Yes: ENTER

End operation: Esc

Set EOF alarm? :

ENTER

△ or ▽

Replace lens of

2.0 inch

2.5 inch

After changing lens, press

AUTO FOCUS and the new focal length will be saved automatically.

l Set power ramp?

If set in Enable condition and cutting speed is 3% or above, under vector mode, the power control is enabled.

If set in Disable, the power control is disabled.

Default : Enable

Set power ramp?

Yes: ENTER

End operation: ESC

Select unit? :

ENTER

Enable **

Ok: ENTER

Change: △ or ▽

Disable

Ok: ENTER

Change: △ or ▽

Select unit?

Yes: ENTER

End operation: ESC

Set EOF alarm? :

Change: △ or ▽

ENTER

l Select unit?

Set unit in Metric or English.

Select unit?

Yes: ENTER

End operation: Esc

Set EOF alarm? :

Metric (mm)**

Ok: ENTER

Change: △ or ▽

English (inch)

Ok: ENTER

Change: △ or ▽

Set EOF alarm?

Ok: ENTER

End Operation: Esc

ENTER

△ or ▽

ENTER

Tune (Auto focusing)? :

NOTE:

** means default or current setting.

l Set EOF alarm?

If set in Enable condition, a beep tone sounds when End OF File.

Set EOF alarm?

Ok: ENTER

End operation: Esc

Tune Auto focusing? :

ENTER

Enable**

Ok: ENTER

Change: △ or ▽

Disable

Ok: ENTER

Change: △ or ▽

ENTER

Tune (Auto focusing)?

Ok: ENTER

End operation: Esc

Select set up #1-16? :

l Tune (Auto focusing)?

In case the focal length of Auto Focus needs to be corrected, please insert the corresponding manual focal tool to the hole of the holder shown as in the Figure of LENS and MANUAL FOCUS GAUGE. Then, operate as follows.

If you have ever pressed

AUTO FOCUS after power ON

Press arrow up/down key to tune focusing position then press ENTER

Tune (Auto focusing)?

Ok: ENTER

End operation: Esc

Select set up #1-16? :

ENTER

If you have not pressed

AUTO FOCUS after power ON

Press AUTO FOCUS key then FUNCTION key

Select the function

Tune (Auto focusing)

Attach manual focus gauge to the carriage and press arrow key up and down to position the working table in focus then press

ENTER.

New focal length has been saved.

Complete tuning

Ready to setup or send a file to

Select set up #1-16?

Yes: ENTER

End operation: Esc

Select baud rate? :

l Select Set Up #1-16?

You can assign 16 different colors individually for speed and power to achieve a variety of cutting effects.

This function works when your software package can output HPGL plot without using VENUS’s

driver.

Select setup #1-16?

Yes: ENTER

End operation: ESC

Select baud rate? :

Setup # 1 **

＋: △ －: ▽

Ok: ENTER

End operation: ESC

ENTER

Change: △ or ▽

Setup # x

＋： △ －： ▽

Ok: ENTER

End operation: ESC

ENTER

Select baud rate?

Yes: ENTER

End operation: ESC

Data bit/parity? :

Press POWER key to change Press SPEED key to

Power change speed

POWER: x x x %

＋： △ －： ▽

SPEED: x x . x %

＋： △ －： ▽

End operation: ESC

ENTER

Save the desired cutting power for not using Venus’s driver

Save the desired cutting speed for not using Venus’s driver

NOTE:

** means default or current setting. l Select baud rate?

Baud rate is to determine the speed of data transmission to communicate with the host computer.

Setting range: 9600, 19200, 38400, 57600, 115200

Defaults: 57600

Select baud rate?

Yes: ENTER

End operation: Esc

Data bit/parity? :

ENTER

57600 bps **

Ok: ENTER

Change: △ or ▽

△ or ▽

xxxxxx bps

Ok: ENTER

Change: △ or ▽

Set data bit/parity?

Ok: ENTER

End operation: Esc

Select language? :

ENTER

NOTE:

** means default or current setting.

l Set data bit/parity?

Data bits refer to the size of one block of data and parity is used to check if data was received correctly or not. The data/parity feature is to adjust the byte format and parity type in order to communicate with the host computer.

Set data bit/parity?

Ok: ENTER

End operation: Esc

Select language? :

ENTER

8 bits no parity **

Ok: ENTER

Change: △ or ▽

△ or ▽

8 bits even parity

Ok: ENTER

Change: △ or ▽

ENTER

Select language?

Yes: ENTER

End operation: Esc

l Enable/Disable auto focus

The manufactures’ default is Auto-focus enable. If auto-focus set as disable, the working table will not lower down automatically as soon as power turned on.

Set data bit/parity?

Yes: ENTER

End operation: ESC

Set autofocusing? :

Set autofocusing?

Yes: ENTER

End operation: Esc

Select language ? :

ENTER

Enable **

Ok: ENTER

Change: △ or ▽

△ or ▽

Disable

Ok: ENTER

Change: △ or ▽

l Select language?

Single file mode

Select language?

Yes: ENTER

End operation: ESC

English **

Ok: ENTER

Change: △ or ▽

xxxxxx

Ok: ENTER

Change: △ or ▽

Do setup or press

STAR key then send only one file

ENTER

△ or ▽

ENTER or ESC

Multi file mode

Do setup or send at least one file then NEXT

FILE key select a file then START

NOTE:

** means default or current setting.

Software Operation

After completing your editing job choose File Print, click “Properties”

Mode:

A. Black & White mode

Let you obtain half-tone effect quickly without going through complex steps of application software

(operating procedures shown as a) Editing file, and b) Engraving, on the following paragraph) to obtain the similar effect. You can choose the look of the laser engraved photo by applying one of the driver software’s halftone options.

Dithering

The gray areas of image will be filled with from a 5- grade halftone with 2x2 dots to a 65- grade halftone with 8x8 dots. 8x8 dithering type would presents the image into different shading effect than the 2x2 dithering, while the 2x2 dithering type would have smaller dots than 8x8, that produces higher resolution. The dithering type choice would depend on the image and application

Enhance Dithering

The enhance dithering as what it reads would help to compensate the shortage of smaller grade halftone type, such as choosing 2x2 dithering type and enhance dithering at the same time, the image would be printed with 256-grade halftone and 2x2 dots. Therefore, better shading effect with small

2x2 dots/ grids.

The error diffusion presents the shade of image as a shade of image as a spread halftone instead of dots, therefore more detailed.

Error Diffusion

Pattern Type

The halftone pattern has three kinds of layout options, which determine the shape of each grid/ dot to compose the shading effect of raster image.

a. Dot: A halftone pattern consists of circle dots.

b. Corner: The dark dot spread from the left upper corner of the pattern result in a little triangle shape to imitate a shading effect.

c. Bayer : A random halftone pattern.

NOTE:

Black & White mode is the easiest way to get the half-tone effect.

However if a higher image quality is required, please refer to the following steps operated by CorelDRAW V. 8.0 and after.

a) Editing file:

Layout Page Setup Set from Printer, Landscape OK

Edit desired file (picture etc.) Bitmap Transfer to Bitmap,

256 shades of gray chose proper DPI OK

Bitmap Convert to Black and White, choose error diffusion OK

b) Engraving (Printout):

File Print Properties, choose Options and the default mode is set up at Manual

color fill then set up proper resolution, power and speed OK

NOTE:

Please refer to “NOTICE” of Quick Menu in the front page.

2*2 dithering

Error Diffusion

4*4 dithering

2x2 Enhance Dithering

8*8 dithering

8x8 Enhance Di

Dot Bayer

B. Manual color fill

Each power and speed setting can be linked to certain color on the layout. Totally 16 color settings arE available. The desired color can be adjusted by changing the ratio of Red, Green and Blue. If the speed or power is set to 0, the corresponding color area or vector line will be invalid.

Corner

C. 3D effect

With this function, we can get the sculpture effect. The engrave image must have gray levels as following photo shows. The engrave image is effected by PPI, DPI, power and speed setting. Please refer to Appendix for parameter settings suggestion.

Sample/ Material: Density Board

3D Image File

D. Stamp Mode

Mainly used in rubber stamp productio n. Create a slope base of stamp characters by setting up the stamp

parameter. Normally the pitch number for engraving a 2~3mm thick rubber pad can be set at 0.2 or 0.3. The smaller the pitch number, the sharper the slope. If setting the pitch number at a very big value, it may take for a very long time for the math calculation. l Pitch Value & Shoulder Power Setting

The finished stamp will be a reversed image with engraved depressions and ridges. Many of these ridges may be too thin and would break off or be unstable. Creating pitch is a way to add support to the thin lines and ridges. The pitch value setting allows you to adjust the width of the ridges. Broad pitch gives the maximum amount of support for each ridge. Experiment with different pitch value

settings in order to produce the stamp that is best suited for your application. You can specify the size into the pitch box under stamp mode and adjust the bar to specify different laser power level for shoulder. l Add Border

You may wish to include a thin or wide border around the outline of your stamp. This can be done by creating outline greater than .001” thickness around the image. When the Mirror setting is selected, this outline will automatically be reserved as a ridge that does get engraved. l Image Invert

The Invert mode will reverse the black and white outlines and fills in the selected image. Black will become white and vice-versa, thus creating a high area that will be covered with ink when the stamp is put to use. This function is disabled when the Manual Color Fill mode.

Invert

l Image Mirror

When using a stamp, the image needs to be reversed or mirrored in order to show up properly when the stamp is in use. This setting will transfer right to left and vice- versa.

Mirror

l Cutting out the stamp

To cut the finished stamp, create a thin(0.001”) red line on the outline edge of the border or where ever you wish the stamp to be cut. The vector setting will always be performed after the engraving is complete. l Stamp Production

You may wish to create a full sheet of duplicated rubber stamps in order to have them all engraved at once, saving on material cost and operational time. To do this, copy and paste the image enough times to fill the page size that is smaller or equivalent to the working table and the rubber sheet. Next make sure that the image is mirrored, inverted and that the appropriate should, border, power and speed settings are in place.

Parameter Settings

The LaserPro Venus allows users of 16 different colors to represent 16 different power and speed settings when cutting and engraving. These colors are referred to as PENS. Try to think of each pen as a designated laser setting, rather than as a color. An image that is only black and white will use only one power and speed laser setting (Black). An image that includes black, red and blue colors will use three different assigned power and speed settings. In order to utilize up to 16 different pens, make sure your graphics program uses the 16 colors recognized by the driver.

A. Pen setting

There are 16 available pen settings to match a specific laser setting with the different colors used in the graphic image. If your image uses black outlines, and red and blue color fills, then the driver will instruct the laser to use three different power and speed settings on the three distinct areas. The speed and power settings designated to each pen color, will represent a proportion of the master control speed and power settings. If you would like to use a color not included in the driver ’s original 16 colors, please double click on the specified pen and the color manager window would jump out then you can select the color you would like to apply.

B. Speed

Speed setting here determines the speed of laser’s motion system during operation. The range is from 0.1%

~ 100%. 100% speed is equivalent to the fastest speed and will be the speed that the motion system travels when cutting or engraving straight lines. The machine will automatically slow down when it is cutting or engraving curves.

C. Power

Power setting here would decide the laser’s power during operation. The range is from 0.1% ~100%. The percentage represents the power of each laser pulse fired. Power and speed work together to determine the depth of a cutting and/or engraving. Higher power and slower speeds will produce the deepest engraving.

D. Raster Vector On / Off

Each color in the graphic image may include a variety of color fills and very thin lines. It is then possible for one pen color to require both raster and vector modes. Turning either Raster or Vector off will force the driver to ignore the pen color’s fills or thin lines. You can check the Raster or Vector box to turn on / off the function.

E. DPI – Dots Per Inch

This setting determines the quality of image resolution was using the raster engraving. DPI can also referred to as horizontal lines per inch or fill spacing. The amount of raster strokes per vertical inch of travel will affect the image resolution of the engraving. Higher DPI settings will have cleaner and deeper engravings, but will take longer to complete. Lower DPI settings will have coarser and more shallow engravings, but will take less time to complete. Experiment with different settings to get your desired effect. You can find the DPI function at Venus driver- Properties- Options.

F. P.P.I.-- Pulse Per Inch.

§ Purpose: By changing the laser firing pulses per inch, the distribution of energy would be changed. n

The adjusted range is 30 to 1500 PPI or you can choose auto mode. When choosing auto mode, the system will come up with the proper PPI value automatically. In order to maintain the quality of raster graph, the PPI value will at least equal to DPI value automatically even you set the lower PPI value than DPI value.

G. Save Parameters Setting

Each job may require unique Mercury driver parameter settings. After you have adjusted all of the settings, remember to save it in a desired location for future use. Press the SAVE icon and save the parameter settings to the proper directory as wished or default for all applications, then you can see the saved files shown in the

History Files column. You can access your saved settings by clicking on Load or by using the History scroll, which keeps track of the settings most recently used.

File parameter setting save, delete or load function.

Review and select the saved file parameter setting here.

Note:

a. These editing options can be saved in image files such as CoreI Draw graphics with printer driver parameters setting inside or can be saved a s the default settings in Mercury driver for future files.

b. Please make sure your ID to log in the computer is set to “Administrator ” level, therefore OS of

2000/XP can allow you to save parameter settings.

Paper

l Paper Size: Set up the working size for engraving. l D-2 Unit: You can choose the unit measurement either with metric or imperial inch. l Scaling Function

Apply this function to adjust the difference in size between the object in the page of software and the real object engraved. Scale can be adjusted up to ± 50/1000. Positive value is to enlarge the size, negative to reduce. For examples, adjust the scale by +10 to enlarge the object’s size by 10/1000.

Advanced Function

l Position Mode n

Home - Focus carriage goes back to the upper right position after finishing a job. n

Without Home - Focus carriage stops at the last position of a data file. You can engrave inside a n bowel or a concave object to prevent hitting the object.

Relative Move - You can place the focus carriage at any place you want to start a job. When finishing a job, the focus carriage will move back to the starting point. You can engrave inside a bowel or a concave object to prevent hitting the object.

l Image Output Direction

n n

Top to Bottom- The laser would engrave from top to bottom of the image.

Bottom to Top- Normally, the LaserPro engravers from top to bottom, left to right. Selecting Bottom

Up will force the machine to start from the bottom and work its way to the rear of the working table.

Some laminates will produce dust that may get lodged in the engraved area if the machine engraves from top to bottom. Since the exhaust system is located at the rear of the machines, the dust will be sucked away from the engraved area. l Vector Setting n

All Raster – when choose “All Raster Output” to print graphic including vector line and raster image, the laser would take the vector line as raster data and print the whole graphics as raster engraving image. n

Vector sorting- When your image has one vector cut area enclosing another vector cut area, this setting will automatically direct the laser to cut out he inside enclosure before moving to the outside image. n

Optimization- This is another setting that will automatically cut down on operation time. When selected, the Venus driver will analyze your image and find the most efficient passing route to complete the job. l Cluster

In order to reduce the working time, the output movement can be clustered under stamp mode. Suppose the

“Distance” you specified is D and the distance between graph A & B is X. If you chose the function

“Cluster” and X > D, the output movement will be route b. If you don’t chose “Cluster” or even you chose

“Cluster” and X = D, the output movement will be route a.

A

B

route a route b

l Border

You can add border at image edge for a better output of the stamp image (refer to Fig. 19). You must select

“Image Invert” (refer to Fig. 16) under stamp mode when using border. As for Fig.17, you can specify the border X and Y. If you chose the “Cluster” and want to have border, the border X and Y must be less than the “Distance” D you specified.

Add border origin

VI. BASIC MAINTENANCE

Caution:

l Keeping the optics and motion system clean is essential to an excellent quality engraving and the reliability of your engraver. Please clean Bearing track and X-axis (DU) bearing daily to maintain good

condition of machine. l Never pour or spray any liquid directly onto the laser system. l Turn off the power and unplug the system before cleaning.

Inside the System:

Open the top door, the front door and the back door (if necessary). Vacuum to clean inside of the engraver and vent area thoroughly.

Engraving Table:

Dampen the paper towel or cloth with alcohol or cleaner to clean the Engraving

Table.

Motion System:

Dampen the cotton swab to clean the rails of the Motion System. Get rid off any debris built up in the bearing tracks.

Bearings:

Hold a dampened cotton swab against the bearing and moving the motion system by hand to clean each bearing.

Mirrors and Lenses:

The focus lens and the mirror located on the carriage are the two components most likely to require cleaning once a week.

Caution:

Don't scratch out the soft coating of the mirror's surface. Excessive cleaning the mirrors and lenses may cause damage and reduce the life of the mirror (refer to Fig. 21).

Clean the mirror -

1. Unscrew and remove front cover of the focus carriage. Release the top screw and pull out mirror carefully

2. Put lens tissue on the mirror and drop a little lens cleaner on the middle area of the tissue, after the fluid has been absorbed evenly, pull the tissue

one direction

gently to clean the mirror.

3. Let it air dry and re- install it.

4. Unscrew and remove the dust prevention box then clean the #2 Mirror, #4 Mirror and #1 Mirror same as above process separately.

Loading hole for manual focal tool

Lens

Tissue

Lens Cleaner

Top Screw

○ (CORRECT)

Do not use cotton swab to rub clean the mirror

Auto-focus gauge

╳ (INCORRECT)

Pull the tissue one direction gently after the cleaner has been absorbed evenly

○ (CORRECT)

Remove

Front Cover

Mirror

Clean the focus lens –

1. Unscrew and remove the front cover of the focus carriage. Pull out focus lens carefully

2. Flood the focus lens with lens cleanser on both sides then using a cotton swab or lens tissue to dry off the remaining solution gently.

3. Do not touch the lens surface with your bare hands or press down hard with any cleaning material.

VII. TROUBLE SHOOTING

Quality Problems

l Check focus length set under the function key to see if it matches the type of the lens installed. l Focus Lenses are not installed correctly. Focus Lens loose in the holder. l Debris or dust builds up in the bearing tracks or X-Axis rails. l The focus lens and the mirror in the carriage are damaged or need to be clean.

Non-operational Problems

Laser beam does not generate

1. If the red alignment beam is not revealed, the laser beam is misalignment.

Adjust reflection mirrors for exact focus.

2. If the red alignment beam is revealed, please check the driver power. The laser power may be too low to be detected. Please increase the percentage setting of the Laser Power from the software driver or the control panel.

3. Please check if the laser power connector is loose.

4. For safety purpose, the laser beam will not be generated when the top or front door is opened unless you short the connector of the magnetic switches.

APPENDIX I. Specification

Laser Source

VENUS V-12

12W

V-35

35W

Work Area

Max. Working Piece

(W×D×Thick)

Table Size

Overall Dimensions

W×D×H

Weight

Drive

Speed Control

Power Control

Sealed CO

laser

11.8"x8.3"

(300mm × 210mm)

14.2"x11.8"x2.8"

(360x300x70mm)

14.2"x11.8"

(360x300mm)

24.4”x17.1”x18.1”

(620x435x500 mm)

32 Kg / 70 lb 37 Kg / 81 lb

DC servo control

Adjustable from 0.02 to 20 inch/sec with up to

16 colors linked speed setting per job

Adjustable from 0∼100% and 16 colors linked power setting per job

Automatic

1000, 600, 500, 300, 250, 200

Print port and serial port for PC

Z Axis Moving

Resolution (DPI)

Computer Interface

Memory Buffer 16MB standard upgradable to 64 MB with

SIMM modules. Multiple file mode saves up to

100 files.

Display Panel 4-line LCD display showing current file name , total working time . Laser power, engraving speed, file loaded into memory buffer, setup and diagnostic menus.

100∼240V, AC Auto Switch

Power

10Amp

Cooling Air-cooled

** Above specification is subject to change without prior notice.

Optional Items: Odor Reduction System

Air Assist System

Compressor for Air Assist System

Dust Prevention Window

Goggle

APPENDIX II. 3D Function

Tip for 3D Application

When doing 3D sample on LaserPro, acrylic or MDF wood are ideal materials for the purpose. For acrylic the suggested PWR is 100%, SPD around 30%(depends on how deep you want to cut).

The perfect image for 3D is like those shown below. When image is ready, choose 3D Effect as the output mode in the driver. Sometimes, some material shows better effect if you run the job with 2nd pass with laser out-of- focus. Especially with acrylic, the 2nd pass will smooth out the surface.

For engraving wood, as it burns easily and leaves blackened surface after the 1st pass, it is necessary to run the

2nd pass to remove the burned surface. To do that, simply fill the image with black colour as the mask (see below) and Run the black mask image with PWR 100% and SPD100%.

Create a black image for polishing

3D engraving / Material: 1cm Acrylic by Venus 12W Lens: 1.5 inch

Step Speed Power DPI PPI

13% 100% 600 auto

Focus

Auto Focus

Remarks

3D Mode Engraving

13% 100% 600 auto Lower down table 2.5mm 3D Mode Engraving

100% 100% 600 800 Lower table again 2 mm Black and White Mode Polishing

0.1% 100% 500 auto Move table up 1.3mm Cutting off

Olá! Eu sou um chatbot de IA especificamente treinado para ajudá-lo com o LaserPro LaserPro VENUS Manual do usuário. Já revisei cuidadosamente o documento e posso ajudá-lo a localizar as informações exatas de que precisa ou explicar o conteúdo de maneira clara e simples. Quer você esteja procurando orientação sobre recursos específicos, etapas de solução de problemas ou uso geral, fique à vontade para fazer suas perguntas. Quanto mais detalhes você fornecer sobre suas preocupações ou necessidades, mais precisamente e eficazmente poderei ajudá-lo!

Assistente digitando

O assistente está fora do teclado. Por favor, tente novamente mais tarde.

Parece que você acessou um documento escrito em vários idiomas, incluindo um que não é seu idioma nativo. Você pode usar os links a seguir para ocultar temporariamente as páginas sem o idioma de sua preferência.

Anúncio