Mitsubishi Electric MODEL GT15-90XLTT BACKLIGHT User Manual
विज्ञापन
विज्ञापन
MODEL GT15-90XLTT
BACKLIGHT
User's Manual
Thank you for purchasing the GOT1000 Series.
Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.
MODEL
MODEL
CODE
GT15-90XLTT-U
1D7M42
IB(NA)-0800327-A(0507)MEE
zSAFETY PRECAUTIONSz
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "DANGER" and
"CAUTION".
DANGER
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.
Note that the CAUTION level may lead to a serious accident according to the circumstances.
Always follow the precautions of both levels because they are important to personal safety.
Please save this manual to make it accessible when required and always forward it to the end user.
[BACKLIGHT REPLACEMENT PRECAUTIONS]
DANGER z Make sure to externally shut off all phases of GOT power supply
(When GOT is connected via the bus type connection, make sure to cut all phases of PLC CPU power supply as well) and remove the GOT from the control panel before backlight replacement.
If all phases are not shut off, it may cause an electric shock.
If backlight is replaced with the GOT on the control panel, the
GOT may drop off, resulting in injuries.
CAUTION z Make sure to wear gloves during backlight replacement.
Failure to do so may cause injuries.
z Make sure to start the backlight replacement 5 or more minutes after power off of the GOT. Failure to do so may cause burn injuries as the old backlight holds heat for a while.
[STARTUP AND MAINTENANCE PRECAUTIONS]
CAUTION z Before handling the GOT, make sure to touch a grounded metal object to discharge the static electricity from the human body.
Failure to do so may cause the GOT to fail or malfunction.
[DISPOSAL PRECAUTIONS]
CAUTION z Dispose of this product as industrial waste.
[TRANSPORTATION PRECAUTIONS]
CAUTION z Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the GT15 User's Manual, as they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Manuals
The following shows manuals relevant to this product.
Detailed Manual
Manual name
GT15 User's Manual
(Option)
Manual Number
(Type code)
SH-080528ENG
(1D7M23)
Relevant Manuals
For relevant manuals, refer to the PDF manual stored within the drawing software used.
© 2005 MITSUBISHI ELECTRIC CORPORATION
1. Overview
This User's Manual describes Model GT15-90XLTT backlight
(hereafter abbreviated to the backlight).
Refer to the GT15 User's Manual for the applicable GOT.
Product name
Backlight
Model name
GT15-90XLTT
Description
For GT1595-X
2. Specifications
The performance specifications of the backlight are indicated below.
Refer to the GT15 User's Manual for the general specifications of the backlight.
Item
Kind
Life
Weight
Specification
Cold cathode tube back light
50,000h (Operating ambient temperature: 25
44g (Equivalent to the weight of two backlights)
)
3. Backlight Replacement
The GOT includes the backlight for liquid crystal display panel.
Please note that the backlight intensity decreases in time.
The backlight needs to be replaced when the display section becomes dark due to the decreased intensity and the picture is unclear.
The backlight replacement procedure is described below.
(1) Power off the GOT.
(2) Disconnect the power supply cable and communication cable.
Remove the GOT from the control panel.
(3) Remove the expansion unit cover on the right side of the
GOT.
Remove the expansion unit, e.g. bus connection unit, if it is mounted.
(4) Remove the GOT rear fixing screws (8 pcs.) with a screwdriver.
A
(5) Remove the case after passing the battery holder through the mounting hole.When removing, take care of not cutting the cable of the battery holder.
(Expanded figure of part A in (4))
(6) Disconnect the cable connector of the upper (H01) backlight and the cable connector of the lower (H02) backlight from the GOT side connectors.
A
(7) Pull the upper backlight by pressing the projecting part of the rubber holder that fixes the backlight with a minus driver to unfasten the backlight.
In the same way, pull the lower backlight by pressing the projection part of the rubber holder that fixes the backlight with a minus driver to unfasten it.
(Expanded figure of part A in (6))
A jut of the rubber holder
(8) Pull the upper backlight out through the hole for backlight replacement on the upper part of the GOT.
In the same way, pull the lower backlight out through the hole for backlight replacement on the lower part of the
GOT.
Hole for backlight replacement
(9) Mount a new backlight in the reverse procedure of removal.
When inserting a new backlight through the hole for backlight replacement of the GOT main unit, take care not to damage the sheath of the cable.
And push the backlight in securely until the projection part of the rubber holder is fixed.
Also assemble the case in the reverse procedure of disassembly. (Tighten the GOT rear fixing screws within the torque range of 0.36 to 0.48N•m).
When mounting the case, take care of not biting the cables between the case and the GOT.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than
Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.
• This product has been manufactured under strict quality control.
However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
Country/Region Sales office/Tel
U.S.A
Brazil
Germany
U.K
Italy
Spain
France
South Africa
Hong Kong
China
Taiwan
Korea
Singapore
Thailand
Indonesia
India
Australia
Mitsubishi Electric Automation Inc.
500 Corporate Woods Parkway Vernon Hills, IL 60061
Tel : +1-847-478-2100
MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.
Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar
Paraiso, Sao Paulo, SP Brazil
Tel : +55-11-5908-8331
Mitsubishi Electric Europe B.V. German Branch
Gothaer Strasse 8 D-40880 Ratingen, GERMANY
Tel : +49-2102-486-0
Mitsubishi Electric Europe B.V. UK Branch
Travellers Lane, Hatfield, Herts., AL10 8XB,UK
Tel : +44-1707-276100
Mitsubishi Electric Europe B.V. Italian Branch
Centro Dir. Colleoni, Pal. Perseo-Ingr.2
Via Paracelso 12, 20041 Agrate B., Milano, Italy
Tel : +39-039-6053344
Mitsubishi Electric Europe B.V. Spanish Branch
Carretera de Rubi 76-80
08190 - Sant Cugat del Valles, Barcelona, Spain
Tel : +34-93-565-3131
Mitsubishi Electric Europe B.V. French Branch
25 Boulevard des Bouvets, F-92741 Nanterre Cedex, France
TEL: +33-1-5568-5568
Circuit Breaker Industries LTD.
Tripswitch Drive, Elandsfontein Gauteng, South Africa
Tel : +27-11-928-2000
Ryoden Automation Ltd.
10th Floor, Manulife Tower, 169 Electric
Road, North Point, HongKong
Tel : +852-2887-8870
Ryoden Automation Shanghai Ltd.
3F Block5 Building Automation
Instrumentation Plaza 103 Cao Bao Rd. Shanghai 200233 China
Tel : +86-21-6120-0808
Setsuyo Enterprise Co., Ltd.
6F., No.105 Wu-Kung 3rd.RD, Wu-Ku Hsiang,
Taipei Hsine, Taiwan
Tel : +886-2-2299-2499
HAN NEUNG TECHNO CO.,LTD.
1F Dong Seo Game Channel Bldg.,660-11, Deungchon-dong
Kangsec-ku, Seoul, Korea
Tel : +82-2-3660-9552
Mitsubishi Electric Asia Pte, Ltd.
307 Alexandra Road #05-01/02,
Mitsubishi Electric Building Singapore 159943
Tel : +65-6473-2308
F. A. Tech Co.,Ltd.
898/28,29,30 S.V.City Building,Office Tower 2, Floor 17-18 Rama 3
Road, Bangkpongpang, Yannawa, Bangkok 10120
Tel : +66-2-682-6522
P.T. Autoteknindo SUMBER MAKMUR
Jl. Muara Karang Selatan Block a Utara No.1 Kav. No.11 Kawasan
Industri/Pergudangan Jakarta - Utara 14440
Tel : +62-21-663-0833
Messung Systems Put,Ltd.
Electronic Sadan NO:111 Unit No15, M.I.D.C BHOSARI,
PUNE-411026, India
Tel : +91-20-712-2807
Mitsubishi Electric Australia Pty. Ltd.
348 Victoria Road, PostalBag, No 2,
Rydalmere, N.S.W 2116, Australia
Tel : +61-2-9684-7777
HEAD OFFICE : 1-8-12, OFFICE TOWER Z 14F HARUMI CHUO-KU 104-6212,JAPAN
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.
Specifications subject to change without notice.
Printed in Japan on recycled paper.
डाउनलोड
विज्ञापन