Mitsubishi GT15 -60VLTT Backlight User's Manual
विज्ञापन
विज्ञापन
MODEL GT15-60VLTT
BACKLIGHT
User's Manual
Thank you for purchasing the GOT1000 Series.
Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.
MODEL
MODEL
CODE
GT15-60VLTT-U
1D7M09
IB(NA)-0800303-D(0704)MEE
z SAFETY PRECAUTIONSz
(Always read these precautions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "DANGER" and
"CAUTION".
DANGER
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.
Note that the CAUTION level may lead to a serious accident according to the circumstances.
Always follow the precautions of both levels because they are important to personal safety.
Please save this manual to make it accessible when required and always forward it to the end user.
[BACKLIGHT REPLACEMENT PRECAUTIONS]
DANGER
z Make sure to externally shut off all phases of GOT power supply
(When GOT is connected via the bus type connection, make sure to cut all phases of PLC CPU power supply as well) and remove the GOT from the control panel before backlight replacement.
If all phases are not shut off, it may cause an electric shock.
If backlight is replaced with the GOT on the control panel, the
GOT may drop off, resulting in injuries.
CAUTION
z Make sure to wear gloves during backlight replacement.
Failure to do so may cause injuries.
z Make sure to start the backlight replacement 5 or more minutes after power off of the GOT. Failure to do so may cause burn injuries as the old backlight holds heat for a while.
[STARTUP AND MAINTENANCE PRECAUTIONS]
CAUTION
z Before handling the GOT, make sure to touch a grounded metal object to discharge the static electricity from the human body.
Failure to do so may cause the GOT to fail or malfunction.
[DISPOSAL PRECAUTIONS]
CAUTION
z Dispose of this product as industrial waste.
[TRANSPORTATION PRECAUTIONS]
CAUTION
z Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the GT15 User's Manual, as they are precision devices.
Failure to do so may cause the unit to fail.
Check if the unit operates correctly after transportation.
Manuals
The following shows manuals relevant to this product.
Detailed Manual
Manual name
GT15 User's Manual
(Option)
Manual Number
(Type code)
SH-080528ENG
(1D7M23)
Relevant Manuals
For relevant manuals, refer to the PDF manual stored within the drawing software used.
© 2004 MITSUBISHI ELECTRIC CORPORATION
1. Overview
This User's Manual describes Model GT15-60VLTT backlight
(hereafter abbreviated to the backlight).
Refer to the GT15 User's Manual for the applicable GOT.
Product name
Backlight
Model name
GT15-60VLTT
Description
For 8.4" VGA liquid crystal
2. Specifications
The performance specifications of the backlight are indicated below.
The general specifications of the backlight are the same as those of the GOT.
For the general specifications of the backlight, refer to GT15
User's Manual.
Item
Kind
Life
Weight
Specification
Cold cathode tube back light
50,000h (Operating ambient temperature: 25
17g (Equivalent to the weight of two backlights)
)
3. Backlight Replacement
The GOT includes the backlight for liquid crystal display panel.
Please note that the backlight intensity decreases in time.
The backlight needs to be replaced when the display section becomes dark due to the decreased intensity and the picture is unclear.
The backlight replacement procedure is described below.
Backlight replacement varies with the hardware version of the applicable GOT.
Before replacement, please confirm the hardware version.
The hardware version is indicated on the rating plate of the
GOT rear face.
For the confirmation method of the hardware version, refer to
GT15 User's Manual.
Model name Hardware version Reference
GT15-60VLTT
D (Apr., 2005) or earlier.
E (Mar., 2005) or later.
3.2
3.1
3.1 Replacement (1)
(1) Power off the GOT.
(2) Disconnect the power supply cable and communication cable.
Remove the GOT from the control panel.
(3) Remove the expansion unit cover on the right side of the
GOT.
Remove the expansion unit, e.g. bus connection unit, if it is mounted.
(4) Remove the GOT rear fixing screws (8 pcs.) with a screwdriver.
A
(5) Remove the case after passing the battery holder through the mounting hole.When removing, take care of not cutting the cable of the battery holder.
(Expanded figure of part A in (4))
(Continued to lower left)
(6) Disconnect the cable connector of the upper (H01) backlight and the cable connector of the lower (H02) backlight from the GOT side connectors.
B A
(Expanded figure of part A in (6))
B
When the GOTs with the following hardware versions are used, remove the cables from the insulation sheets for protecting cables.
• GT1565-VTBA(Hardwear version W or later)
• GT1565-VTBD(Hardwear version N or later)
B
Insulation sheets for protecting cables B
(7) Remove the cables of the upper connector (H01) from the
2 slits (black).
Similarly, remove the cables of the upper connector (H02) from the 2 slits (black).
(Expanded figure of part B in (6))
(8) Press the upper backlight fixing latch (black) with your finger, and pull out the backlight to the left. Similarly, press the lower backlight fixing latch (black) with your finger, and pull out the backlight to the left.
Latch
(9) Mount a new backlight in the reverse procedure of removal.
When the GOT with the insulation sheets for protecting cables is used, place the cables between the insulation sheet and the insulation sheets for protecting cables.
When connecting the cable connectors of the backlight and the GOT unit, connect by crossing the cable connectors each other as the below.
The following figure shows an example with the insulation sheets for protecting cables.
Insulation sheets for protecting cables
Also assemble the case in the reverse procedure of disassembly. (Tighten the GOT rear fixing screws within the torque range of 0.36 to 0.48N•m).
When mounting the case, take care of not biting the cables between the case and the GOT.
3.2 Replacement (2)
(1) Power off the GOT.
(2) Disconnect the power supply cable and communication cable. Remove the GOT from the control panel.
(3) Remove the expansion unit cover on the right side of the
GOT. Remove the expansion unit, e.g. bus connection unit, if it is mounted.
(4) Remove the GOT rear fixing screws (8 pcs.) with a screwdriver, and remove the case.
Screw A must be tighten in the torque range of 0.186 to
0.245 N•m, as it is made of plastic.
A
(5) Disconnect the cable connector of the upper (H01) backlight and the cable connector of the lower (H02) backlight from the GOT side connectors.
(6) Press the upper backlight fixing latch (black) with your finger, and pull out the backlight to the left. Similarly, press the lower backlight fixing latch (black) with your finger, and pull out the backlight to the left.
(7) Mount a new backlight in the reverse procedure of removal.
Also assemble the case in the reverse procedure of disassembly. (Tighten the GOT rear fixing screws within the following torque range:
Screw A: 0.186 to 0.245 N•m
Other screws: 0.36 to 0.48N•m.)
When mounting the case, take care of not biting the cables between the case and the GOT.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than
Mitsubishi products; and to other duties.
For safe use
• This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.
• This product has been manufactured under strict quality control.
However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.
Country/Region Sales office/Tel
U.S.A
Brazil
Germany
U.K
Italy
Spain
France
South Africa
Hong Kong
China
Taiwan
Korea
Singapore
Thailand
Indonesia
India
Australia
Mitsubishi Electric Automation Inc.
500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A.
Tel : +1-847-478-2100
MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.
Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar
Paraiso, Sao Paulo, SP Brazil
Tel : +55-11-5908-8331
Mitsubishi Electric Europe B.V. German Branch
Gothaer Strasse 8 D-40880 Ratingen, GERMANY
Tel : +49-2102-486-0
Mitsubishi Electric Europe B.V. UK Branch
Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K.
Tel : +44-1707-276100
Mitsubishi Electric Europe B.V. Italian Branch
Centro Dir. Colleoni, Pal. Perseo-Ingr.2
Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy
Tel : +39-039-60531
Mitsubishi Electric Europe B.V. Spanish Branch
Carretera de Rubi 76-80,
E-08190 Sant Cugat del Valles, Barcelona, Spain
Tel : +34-93-565-3131
Mitsubishi Electric Europe B.V. French Branch
25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France
TEL: +33-1-5568-5568
Circuit Breaker Industries Ltd.
Private Bag 2016, ZA-1600 Isando, South Africa
Tel : +27-11-928-2000
Mitsubishi Electric Automation (Hong Kong) Ltd.
10th Floor, Manulife Tower, 169 Electric
Road, North Point, Hong Kong
Tel : +852-2887-8870
Mitsubishi Electric Automation (Shanghai) Ltd.
4/F Zhi Fu Plazz, No.80 Xin Chang Road,
Shanghai 200003, China
Tel : +86-21-6120-0808
Setsuyo Enterprise Co., Ltd.
6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang,
Taipei Hsine, Taiwan
Tel : +886-2-2299-2499
Mitsubishi Electric Automation Korea Co., Ltd.
1480-6, Gayang-dong, Gangseo-ku Seoul
157-200, Korea
Tel : +82-2-3660-9552
Mitsubishi Electric Asia Pte, Ltd.
307 Alexandra Road #05-01/02,
Mitsubishi Electric Building, Singapore 159943
Tel : +65-6470-2460
Mitsubishi Electric Automation (Thailand) Co., Ltd.
Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd,
T.Kannayao, A.Kannayao, Bangkok 10230 Thailand
Tel : +66-2-517-1326
P.T. Autoteknindo Sumber Makmur
Muara Karang Selatan, Block A/Utara
No.1 Kav. No.11 Kawasan Industri Pergudangan
Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia
Tel : +62-21-6630833
Messung Systems Pvt, Ltd.
Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari,
Pune-411026, India
Tel : +91-20-2712-3130
Mitsubishi Electric Australia Pty. Ltd.
348 Victoria Road, Rydalmere, N.S.W 2116, Australia
Tel : +61-2-9684-7777
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.
Specifications subject to change without notice.
Printed in Japan on recycled paper.
डाउनलोड
विज्ञापन