Multiple Display Control Protocol

SEC-VD-DSW Multiple Display Control

Ver. 14.1c

2017-04-20

Multiple Display Control Protocol

Copyright © 2004 2016 Samsung Electronics Co., Ltd

SEC-VD-DSW Multiple Display Control

Ver. 14.1c

2017-04-20

0

Copyright notice

This document is Copyright © Samsung Electronics, Co. - all rights reserved.

Writer : Display S/W, Video Display Division.

Summery : Common protocol specification of MDC(Multiple Display Control)

Revision History :

Version Date

13.7c

13.8c

13.9c

14.0c

14.1c

Contents

2016.02.23 MDC spec common use spec based on v13.7

1. Several detail description is fixed(ikes terms)

2. 0x58 Manual Lamp control

- note is changed.

3. 0x10 Model Number Control

- model code add

- addproduct to model code 0x54

4. 0x15 Picture Size

- Add PC mode scustom option

- Not changed based on model number control

5. 0x14. Input Source Control

- add Web Browser source : 0x65


- model code add

-Add model code on 0x61,0x62

-Model Code error fix from the code 0x54

2. Picture Size

-Add new model code 0x60,0x61,0x62 in table

1. Change range of TV or Monitor ID

- change TV or monitor ID range to 225


-model code add (0x5F , 0x63, 0x64)

3. Add Annex B.2 ~B.3

- HKIA option specific description add


- model code add(0x65 , 0x66 and 0x57)

2. 0x14 Input Source Control

- add OCM

3. 0x72 Sound mdoe

- Add 0x06, Optimized mode

4. 0x3E Color Tone detail option change

5. 0x63 Ticker

- Foreground / Background opacity option description change

6. 0xCA System Menu

- Add 0x92 Touch Control Admin Lock

Writer Approver

1. INTERFACE

1.1. Connection Method

There are 2 available ways of connecting. one is RS232, the other is RJ45.

1.1.1 Connection method ( with RS232 )

- As of Figure 1-1, connect RS232-In(9Pin) to Personal Computer, connect the next TV of Display to be connected from RS232-Out (9Pin).

- In doing so, each TV or Monitor ID can be given from 0 to 225.

- ID cannot be given duplicated.

- When granting ID, it does not need to be given out in the connecting order.

Figure1-1 PC,TV or Monitor connecting method(with RS232)

1.1.2 Connecting method(with RJ45)

- There are several ways to connect Personal Computer and TV(or Monitor).

- As of Figure 1-2, connect Hub and Personal Computer(using Ethernet). connect each TV of Display to be connected to the Hub.

- In doing so, each TV or Monitor must have an IP address.

- TV or Monitor connected by protocol's IP address must have the same ID with the protocol's ID.

- Each TV or Monitor ID can be duplicated.

Figure1-2 PC,TV or Monitor connecting method(with RJ45)

1.1.3 Connecting method(with RJ45 & RS232C)

- As of Figure 1-3, connect TV and Personal Computer(using Ethernet), connect the next TV of Display to be connected from RS232-Out (9Pin).

- In doing so, only TV(connected to Personal Computer) needs an IP address. and each TV or Monitor ID can be given from 0 to 225.

- ID cannot be given duplicated.

- When granting ID, it does not need to be given out in the connecting order.

Figure1-3 PC,TV or Monitor connecting method(with RJ45 & RS232C)

1.2. Connection Spec

1.2.1 RS232 Connection Spec.

- Interactive communications using RS232.

- Of RS232 standards, three signals RxD(No.2), TxD(No.3) and GND(No.5) are used

→ Refer to Figure 2-1

- Limit the distance between devices to less than 4m.

- Currently, out of 9 PIN RS232 terminal, PINS in use are numbers 2, 3 and 5.

- ID should show hexadecimal value of assigned ID.

- Every communication will be made in hexadecimals and Checksum is the sum of all remainings.

If it exceeds two digits, for example, it is 11+FE+01+01=111, discard the number in the first digit like below.

example) Power On & ID=FE

Header Command Data Length Data 1

ID

→

0xAA 0x11 1 Power

Check

Sum


0xFE 11

0xAA 0x11 1 1

- If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID part to "0xFE" and send commands. At the time, each SET will follow commands but it will not respond with ACK.

Table 2-1 RS232 Network spec

Bits Rate 9600 bps

Data Bits

Parity

Stop Bits

Flow Control

8 bits

None

1 bit

None

Figure 2-1 RS-232 pin out DB-9 pin used for Asynchronous Data

1.2.2 RJ45 Connection Spec.

-

Interactive communications using RJ45.

- Transmit the MDC protocol using TCP/IP Format. the protocol information is stored in data area.

- The protocol information format is the same as RS232's.

example) Power Off & ID=0

Header Command Data Length Data1

ID Checksum

0xAA 0x11 1 Power

IP

TCP UDP

ICMP ARP

Hardware Interface(Ethernet, PPP etc. )

RARP

→

Header

0xAA

Command

0x11

0xFE

Data Length

1

Data1

0

10

TCP UDP

IP ICMP ARP RARP

Hardware Interface(Ethernet, PPP etc. )

- default ip : 192.168.0.10 PORT : 1515

- The RJ45 plug has 8-Pins as below.

Table 2-2 RJ45 plug 8-Pins

RJ45 PIN# Wire Color(T568A)

10Base-T Signal

100Base-TX Signal

3

4

5

1

2

6

7

8

White/Green

Green

White/Orange

Blue

White/Blue

Orange

White/Brown

Brown

Transmit+

Transmit-

Receive+

Unused

Unused

Receive-

Unused

Unused

1000Base-T Signal

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

2. Command

Command

No

0x27

0x28

0x2F

0x30

0x31

0x32

0x33

0x34

0x15

0x17

0x18

0x19

0x1D

0x24

0x25

0x26

0x0D

0x0E

0x0F

0x10

0x11

0x12

0x13

0x14

0x00

0x04

0x06

0x07

0x08

0x09

0x0B

Command Type

Status Control

Video Control

RGB Control

PIP Status Control

Maintenance Control

Sound Control

Serial Number Control

Display Status Control

SW Version Control

Auto Motion Plus

Model Number Control

Power Control

Volume Control

Mute Control

Input Source Control

Image Size Control

Direct Channel Control (DTV)

Screen Mode Control

Screen Size Control

MDC Connection Type

Contrast Control

Brightness Control

Sharpness Control

Color Control

Tint Control

Coarse Control

Fine Control

H-Position Control

V-Position Control

Auto Power

Clear Menu Control

Sub Command

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

Data Type

Discrete

Multi Param

Discrete

Discrete

Discrete

0 ~ 100

0 ~ 100

0 ~ 100

0 ~ 100

0 ~ 100

0, 1

0, 1

0, 1

0, 1

0, 1

0

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

String

Multi Param

String

Multi Param

Multi Param

Discrete

0 ~ 100

0, 1

Discrete

Remote Control

RGB Contrast Control

RGB Brightness Control

PIP On/Off Control

Auto Adjustment Control

Color Tone Control

Color Temperature Control

PIP Source Control

PIP Size Control

PIP Locate Control

Fan Speed Setting

User Auto Color

Sound Select Control

Auto Volume

Standby Control

Video Picture Position & Size

Pixel Shift Control

EQ 100Hz Control

EQ 300Hz Control

EQ 1kHz Control

EQ 3kHz Control

EQ 10kHz Control

Auto Lamp Control

Manual Lamp Control

Safety Screen Run Control

Inverse Control

Safety Screen Control (MFM)

Video Wall Mode Control

Safety Lock

Key Lock Control (MFM)

Channel Up/Down

Volume Up/Down

Ticker

Sound Select Control

PC Module Detect

Device Name

0x5A

0x5B

0x5C

0x5D

0x5F

0x61

0x62

0x63

0x51

0x52

0x53

0x54

0x55

0x57

0x58

0x59

0x65

0x66

0x67

0x3F

0x40

0x42

0x43

0x44

0x45

0x47

0x48

0x4A

0x4B

0x4C

0x36

0x37

0x38

0x3C

0x3D

0x3E

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

0 ~ 20

Multi Param

0 ~ 100

Discrete

0, 1

Multi Param

0, 1

0, 1

0, 1

0, 1

0, 1

Multi Param

0, 1

Discrete

String

0, 1

0 ~ 100

0 ~ 100

0, 1

0

Discrete

Discrete

Discrete

Discrete

Discrete

0 ~ 100

0, 1

0, 1

Discrete

Discrete

Multi Param

Multi Param

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0x96

0x9C

0x9D

0x9E

0x9F

0xA1

0xA3

0xA4

0xA5

0xA6

0xA7

0xA8

0xA9

0x76

0x77

0x78

0x79

0x83

0x84

0x85

0x86

0x87

0x89

0x8A

0x8B

0x8C

0x8F

0x92

0x94

0x95

0x68

0x70

0x71

0x72

0x73

0x75

Speaker Select

OSD Off/On

P. Mode Control

S. Mode Control

Digital NR

PC Color Tone Control

Auto Auto Adjustment

All Keys Lock

SRS TSXT Control

Film Mode

Panel On Time

Video Wall On

Temperature Control

Brightness Sensor

Dynamic Contrast

Video Wall User Control

Model Name

Video Wall Direct User Control

Video Wall Feature Control

Fan

Energy Saving

HDMI Black Level

Black Adjust

Gamma

Edge Enhancement

Color Space xvYCC

Reset Control

Ambient Brightness Mode

OSD Display Type On/Off

Timer 1 Control_MFM

Timer 2 Control_MFM

Timer 3 Control_MFM

Clock Control_MFM

Holiday Add/Delete Control

Holiday Get Control

-

-

-

-

0x81 : Frame Alignment

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

Discrete

0, 1

Discrete

0, 1

Discrete

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

Multi Param

0, 1

0, 1

Discrete

Discrete

Discrete

Discrete

0, 1

0, 1

0, 1

Discrete

Multi Param

0, 1

75 ~ 124

0, 1

Discrete

Multi Param

String

Multi Param

0~2

0, 1

Discrete

0, 1

Discrete

0xAB

0xAC

0xAD

0xAE

0xAF

0xB0

0xB1

0xB3

0xB5

0xB6

Timer4 Control

Timer5 Control

Timer6 Control

Timer7 Control

Edit Name Control

Virtual Remote Control

Display Port Daisy Chain

Video Conference Sound Mode

Control

Network Standby Control

DST (Daylight Saving Time)

Control

Custom PIP Control

Auto ID Setting Status Control

Display ID Infomation

Clock Control_MFM

Eco Solution

-

-

-

-

-

-

-

-

-

-

0xB7

0xB8

0xB9

0xC5

0xC6

0xC7

0xC8

0xCA

0xE0

0xE4

0xF9

0xFD

Execute Launcher

OnScreen Display Menu

Control

System Menu Control

Net PIP Command

Apply To Control

Panel On Off

Auto ID

0x81 : Auto Power Off

0x81 : Launcher Mode

0x82 : URL Address

-

-

-

-

0x81 : Menu Orientation

0x82 : Source Orientation

0x83 : Aspect Ratio (Rotated)

0x84 : PIP Orientation

0x81 : Auto Source Switch OnOff

0x82 : Auto Source Switch Control

0x91 : Power Button

0x92 : Touch control Admin Lock

0xA1 : No Signal Power Off

-

-

-

-

0xFF ACK/NAK -

Note : Depends on each model spec, a certain command will be supported or not

Depends on each model spec, an option of a certain command will be differ

Multi Param

Multi Param

Multi Param

Multi Param

Discrete

Discrete

0, 1

0, 1

0, 1

Multi Param

Multi Param

0, 1

0, 1

Multi Param

Discrete

Discrete

String

Discrete

Discrete

Discrete

Discrete

Discrete

Multi Param

0, 1

0, 1

Discrete

Multi Param

0, 1

0, 1

Multi Param

2.1 Common Protocol

2.1.00 Status Control

●

Function

Personal Computer shows current setting condition of TV / Monitor.

●

Get Status

Header

Command Data Length

0xAA 0x00

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak r-CMD

0xAA 0xFF 0x09 'A' 0x00

Val 3

Mute

Val 4

Input

Val 5

Aspect

Val 6 Val 7

N Time NF F Time NF

Check

Sum

Val 1

Power

Val 2

Volume

Power : Power code to be set on TV / Monitor

Volume : Volume value code ( 0 ~ 100 ) to be set on TV / Monitor

Mute : Mute code to be set on TV / Monitor

Input : Input Source code to be set on TV/Monitor

Aspect : Image Size code to be set on TV/Monitor

Note : If use New Timer (0xA4, 0xA5, 0xA6, 0xA7, 0xA8, 0xA9) command. Do as below.

●

Nak

Header

N Time NF : OnTime ON/OFF value of time to set TV/Monitor(old type Timer)

F Time NF : OffTime ON/OFF value of time to set TV/Monitor(old type Timer)

→ It was supported for old type Timer. Now, It is always 0x00.

Command

ID

Data Length Ack/Nak r-CMD Val 1

0xAA 0xFF 3 'N' 0x00 ERR

ERR

:

Error code that shows what occurred error is

Check

Sum

2.1.04 Video Control

●

Function

Personal Computer shows the screen condition of TV / Monitor.

●

Working Condition

1. ATV, DTV, AV, S-Video, Component, HDMI Only

2. A product which has **** Text , **** Video/Image and Calibration as picture mode,

It will not affected by the 1st condition and instead,

It will be work with **** Video/Image of picture mode in the menu

●

Get Video Status

Header Command Data Length

0xAA 0x04

ID

0x00

Check

Sum

●

Ack

Header Command

ID


0xAA 0xFF 0x0A 'A' 0x04 Contrast

Val 2

Brightness

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8

Check

Sum

Sharpness Color Tint ColorTone ColorTemp 0

Contrast : Contrast value to set the TV / Monitor (0 ~ 100)

Brightness : Brightness value to set the TV / Monitor (0 ~ 100)

Sharpness : Sharpness value to set the TV / Monitor (0 ~ 100)

Color : Color value to set the TV / Monitor (0 ~ 100)

Tint : Tint value to set the TV / Monitor (0 ~ 100)

Color Tone : Color Tone value to set the TV / Monitor

ColorTemp : Color Temperature value to set the TV / Monitor

●

Nak

Header Command Data Length Ack/Nak

ID r-CMD

0xAA 0xFF 0x03 'N' 0x04

Val 1

ERR

Check

Sum

ERR : Error code that shows what occurred error is

2.1.06 RGB Control

●

Function

Personal Computer shows screen condition of TV / Monitor.

●

Working Condition

1. PC, BNC, DVI Only

(On the DVI source Red, Green, Blue Gainwill not work)



It will be work with **** Text of picture mode in the menu

●

Get RGB Status


0x06

ID

0x00

Check

Sum

●

Ack

0xAA

Header Command Data Length Ack/Nak r-CMD Val 1

ID

0xAA 0xFF 0x0A 'A' 0x06 Contrast

Val 2

Brightness

Val 3 Val 4

ColorTone ColorTemp

Val 5

0

Val 6 Val 7 Val 8

Red Gain Green Gain Blue Gain

Check

Sum

Val 1 ~ Val 8 : Same as above

Note : If LFD model doesn't support RGB Gain, those values should be replied with 0xFF.

If then MDC application can ignore these values.

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x06

Val 1

ERR

Check

Sum


2.1.07 PIP Status Control

●

Function

T

he PC displays the PIP settings of a TV or monitor.

●

Get PIP Status


0xAA 0x07

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x06 'A' r-CMD

0x07

Val 3 Val 4

Check

Sum

0 0

P.Size

: The PIP size code set for the TV or monitor.

Note : For the detail, pls refer 0x42 PIP Size control command

P.Source

: The PIP source code set for the TV or monitor.

●

Nak

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x03 'N' r-CMD

0x07

ERR : The error code indicating which error occurred

.

Val 1

P.Size

Val 2

P.Source

Val 1

ERR

Check

Sum

2.1.08 Maintenance Control

●

Function

Personal Computer shows maintenance state of TV / Monitor.

Note : Depends on each model spec 0x15data length or 0x19 data length format will be supported

●

Get Maintenance Status


ID Check Sum

0xAA 0x08 0x00

●

Ack

. Data Length 0x15

Header Command

ID

Data Length Ack/Nak r-CMD Val 1 Val 2

0xAA 0xFF 0x15 'A' 0x08 Power P.Size

Val 3

P.Source

Val 4

LMax_H

Val 5

LMax_M

Val 6 Val 7

LMax_AP LMaxValue

Val 8

LMin_H

Val 9

LMin_M

Val 10

LMin_AP

Val 11

LMin

Value

Val 12

Lamp

Value

Val 13

Screen

Interval

Val 14

Screen

Time

Val 15

Screen

Type

Val 16

V.Wall

Val 17

V.Wall

Format

Val 18

V.Wall

Divid

Val 19

V.Wall

Set

Check

Sum

. Data Length 0x19

Header Command

0xAA

Val 3

0xFF

Val 4

P.Source

Val 11

LMin

Value

LMax_H

Val 12

Lamp

Value

ID

Val 5

LMax_M

Val 13

Start Time

- Hour

Data Length Ack/Nak

0x19 'A'

Val 6

LMax_AP

Val 7

LMax

Value

Val 15 Val 14

Start Time-

Min

Screen

Type r-CMD

0x08

Val 8

LMin_H

Val 16

Start Time- am/pm

Val 19 Val 20 Val 21 Val 22 Val 23

End Time- am/pm

V.Wall

V.Wall

Format

V.Wall

Divid

V.Wall

Set

Check

Sum

Power : Power code set on TV / Monitor

P.Size

: PIP Size value code set on TV / Monitor

P.Source

: Source value code set on TV / Monitor

LMax_H : Auto Lamp Max Time Hour (1 ~ 12) set on TV / Monitor

LMax_M : Auto Lamp Max Time Minute (0 ~ 59) set on TV / Monitor

LMax_AP : Auto Lamp Max Time AM/PM set on TV / Monitor

LMaxValue : Auto Lamp Max value (0 ~ 100) set on TV / Monitor

LMin_H : Auto Lamp Min Time Hour (1 ~ 12) set on TV / Monitor

LMin_M : Auto Lamp Min Time Minute (0 ~ 59) set on TV / Monitor

Val 1

Power

Val 9

LMin_M

Val 17

End Time

- Hour

Val 2

P.Size

Val 10

LMin_AP

Val 18

End Time-

Min.

LMin_AP : Auto Lamp Min Time AM/PM set on TV / Monitor

LMinValue : Auto Lamp Min value (0 ~ 100, 0xFF) set on TV / Monitor

LampValue : Manual Lamp Control value (0 ~ 100, 0xFF) set on TV / Monitor

ScreenInterval : Safety Screen Interval (Per Hour, 0(0ff)~10) set on TV / Monitor

ScreenTime : Safety Screen Time (Per Second, 0(off) ~5) set on TV / Monitor

ScreenType : SBP Type Code set on TV / Monitor

Note : Case : Value is not 0x00 : BIT 7 is 0 → Timer set Repeat.

BIT 7 is 1 → Timer set Interval.

- The data transmission(The following combinations), NAK processing.

(1) Data Length 15 & Type's kind Timer Interval

0x00

(2) Data Length 19 & Type's kind Timer Repeat

OFF 0x00 OFF

0x01

0x02

0x81

0x82

0x03

0x04

0x05

0x06

0x09

0x0A

...

0x10

Scroll

(Timer : Repeat)

Pixel

(Timer : Repeat)

Bar

(Timer : Repeat)

Eraser

(Timer : Repeat)

All White

(Timer : Repeat)

Pattern

(Timer : Repeat)

Rolling Bar

(Timer : Repeat)

0x83

0x84

0x85

0x86

0x89

0x8A

...

0x90

Scroll

(Timer : Interval)

Pixel

(Timer : Interval)

Bar

(Timer : Interval)

Eraser

(Timer : Interval)

All White

(Timer : Interval)

Pattern

(Timer : Interval)

Rolling Bar

(Timer : Interval)

0x11

Fading Screen

(Timer : Repeat)

Start Time-Hour : Start Time Hour value ( 1 ~ 12 )

Start Time-Min : Start Time Minute value ( 0 ~ 59 )

0x91

Start Time-am/pm : Start Time AM/PM ( 0 ~ 1 ), 1 : AM, 0 : PM

End Time-Hour : Start Time Hour value ( 1 ~ 12 )

End Time-Min : Start Time Minute value ( 0 ~ 59 )

End Time-am/pm : Start Time AM/PM ( 0 ~ 1 ), 1 : AM, 0 : PM

V.Wall

: code set on TV / Monitor

V.WallFormat

: Video Wall Format code set on TV / Monitor

V.WallDivid

: Video Wall Divider code set on TV / Monitor

V.WallSet

: Video f Set Number code set on TV / Monitor

Note : If LMinValue is returned to 0xFF then Auto Lamp Control is OFF.

Fading Screen

(Timer : Interval)

If LampValue is returned to 0xFF then Manual Lamp Control is OFF.

If videlwall related field returned as 0xFF then videowall is not suooprted

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'N'

ERR : Error code that shows what occurred error is r-CMD

0x08

Val 1

ERR

Check

Sum

2.1.09 Sound Control

●

Function

Personal Computer shows Sound state of TV / Monitor

●

Get Audio Status


0xAA 0x09

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x0D 'A'

Val 3

100Hz

Val 4

300Hz

Val 5

1kHz

Val 6

3kHz

Val 7

10kHz r-CMD

0x09

Val 8

0

Val 1

Vol

Val 9

0

Val 2

Balance

Val 10

0

Val 11

SRS

Check

Sum

Vol, Balance : Vol, Balance value set on TV / Monitor

100Hz, 300Hz, 1kHz, 3kHz, 10kHz : Each the frequency of the Equalizer value set on TV / Monitor

SRS : SRS TSXT On/Off value set on TV / Monitor

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x09

Val 1

ERR

Check

Sum


2.1.0B Serial Number Control

●

Function

Personal Computer controls serial number of TV / Monitor.

●

Get SerialNum Status


0xAA 0x0B

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x14 'A'

Val 3

Data3

Val 11

Val 4

Data4

Val 12

Val 5

Data5

…

Val 6

Data6

Val 15

Val 7

Data7

Val 16

Data11 Data12 … Data15 Data16

Data 1 ~ Data 15 : Serial Number set on TV / Monitor.

Data 16 ~ Data 18 : Reserved

●

Nak


ID

0xAA 0xFF 0x03 'N'


0x0B

Val 8

Data8

Val 17

Data17 r-CMD

0x0B

Val 1

Data1

Val 9

Data9

Val 18

Data18

Val 1

ERR

Val 2

Data2

Val 10

Data10

Check

Sum

Check

Sum

2.1.0D Display Status Control

●

Function

Personal Computer shows display condition of TV / Monitor.

●

Get Maintenance Status


0xAA 0x0D

ID

0x00

Check

Sum

●

Ack


ID


0x0D

Val 1

Lamp

Val 2

Temperatur e

Val 3 Val 4 Val 5 Val 6

Bright_Sens or

No_Sync Cur_Temp FAN

Check

Sum

Lamp

: Lamp Error code (0 : Normal, 1 : Error) to be set on TV / Monitor

Temperature : Temperature Error code (0: Normal, 1: Error) to be set on TV / Monitor

Bright_Sensor : Brighte Sensor Error code (0: NONE, 1: Error, 2: NORMAL) to be set on TV/Monitor

No_Sync : Sync Error code(0: Normal, 1: Error, No Sync) to be set on TV / Monitor

Cur_Temp : Current temperature of TV / Monitor ( 0℃ ~ 125℃ )

FAN : Fan Error code (0 : Normal, 1 : Error) to be set on TV / Monitor

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x0D

Val 1

ERR

Check

Sum


2.1.0E SW Version Control

●

Function

Personal Computer shows version information of TV / Monitor.

●

Get Version Status


0xAA 0x0E

ID

0x00

Check

Sum

●

Ack

Header Command Data Length Ack/Nak r-CMD

ID

0xAA 0xFF 0x34(MAX) 'A' 0x0E

Val 3

Version3

Val 4

Version4

Val 5

Version5

Val 6

Version6

Val 7

Version7

Val 8

Version8

Val 1

Version1

Val 2

Version2

Val 9 Val 10

Version9 Version10

Val 11 Val 12 Val 13 Val 14 Val 15 … …

Check

Sum

Version11 Version12 Version13 Version14 Version15 … …

Version1

~

Version12 :

Project Info. of TV/Monitor

Version13 ~ Version50 : Software version of TV/Monitor

Note : Because Version information is variable, The Data Length 2-52 (0x34) is variably value

( Real Value Val(0~50) +2 (Ack/Nak, r-CMD) )

●

Nak


0xAA 0xFF

ID

0x03 'N' 0x06 ERR

Check

Sum


2.1.0F Auto Motion Plus

●

Function

Personal Computer controls the Auto Motion Plus that TV / Monitor.

Note : It is dependent on Product Specifications- 120Hz Panel.

●

Get Auto Motion Plus Status


0xAA 0x0F

ID

0x00

Check

Sum

●

Set Auto Motion Plus Status

Header Command Data Length Data 1 Data 2

ID

0xAA 0x0F 0x03 Mode

Blur

Reduction

Mode

0x00 Off

0x01 Clear

Data 3

Judder

Reduction

Check

Sum

0x02

0x03

0x04

Standard

Smooth

Custom

0x05 Demo

Blur reduction : It is only for "Mode: Custom". If "Mode" is not custom, then it is "don't care". ( 0 ~

10 )

Judder reduction : It is only for "Mode: Custom". If "Mode" is not custom, then it is "don't care". ( 0 ~

10 )

●

Ack

Header Command Data Length Ack/Nak r-CMD Val 1 Val 2

ID

0xAA 0xFF 0x05 'A' 0x0F Mode

Blur

Reduction

Val 3

Judder

Reduction

Check

Sum

Mode : Same as above

Blur Reduction, Judder Reduction :

Ack For Set command Type, Data2 and Data3 is same with Set command.

●

Nak

Ack For Get command Type, Date2 and Data2 is LFD's Value.(even If "Mode" is not custom.)


0xAA 0xFF

ID

0x03 'N' 0x0F ERR

Check

Sum


2.1.10 Model Number Control

●

Function

Personal Computer shows Model Number of TV / Monitor

●

Get Model Number Status


0xAA 0x10

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x05 'A'

Val 3

TV

Check

Sum

Species : TV / Monitor 's Panel Type.

0x01 PDP

0x02

0x03

0x04

LCD

DLP

LED

0x05

0x06

CRT

OLED

Model : TV / Monitor's Model Number.

Value Model Name

0x01 PPM50H2

0x02 PPM42S2

0x03

0x04

0x05

0x06

0x07

0x08

0x09

0x0A

0x0B

0x0C

0x0D

PS-42P2ST

PS-50P2HT

SyncMaster 400T

SyncMaster 403T

PPM42S3,

SPD-42P3SM

PPM50H3,

SPD-50P3HM

PPM63H3,

SPD-63P3HM

PS-42P3ST

SyncMaster 323T

SyncMaster 403T - CT40CS(N)

PPMxxM5x r-CMD

0x10

Val 1

Species

Remarks

IC Vender IC Name

Etc IC

(Color Enhanc er)

Val 2

Model

0x1E

0x1F

0x20

0x21

0x22

0x23

0x24

0x25

0x26

0x27

0x0E

0x0F

0x10

0x11

0x12

0x13

0x14

0x15

0x16

0x17

0x18

0x19

0x1A

0x1B

0x1C

0x1D

SyncMaster 320P(n)

SyncMaster 400P(n)

SyncMaster 460P(n)

-

SyncMaster 320PX

SyncMaster 400PX(n)

SyncMaster 460PX(n)

-

-

SyncMaster 400TX(n)

SyncMaster 570DX

SyncMaster 320DX(n)

SyncMaster 400DX(n)

SyncMaster 460DX(n)

SyncMaster 700DX(n)

SyncMaster 820DX(n)

SyncMaster 460TX(n)

SyncMaster 400UX(n)

SyncMaster 460UX(n)

SyncMaster 460DR(n)

SyncMaster 42TS

SyncMaster 42PS

SyncMaster P42HP

SyncMaster P50Hn

SyncMaster P50F(n)

SyncMaster P50FP

SyncMaster P63F(n)

SyncMaster P63FP

SyncMaster 320MX(n)

SyncMaster 400CX(n)

SyncMaster 400MX(n)

SyncMaster 400MP(n)

-

-

SyncMaster 460CX(n)

SyncMaster 460MP(n)

SyncMaster 520DX(n)

SyncMaster 400UXn-UD

SyncMaster 460UXn-UD

SyncMaster 400FX(n)

SyncMaster 460DRn-A

SyncMaster 460UTn-UD

SyncMaster 460UT(n)

SyncMaster 320MX(n)-2

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

Lola

Lola

Lola

Lola

Lola

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR Lola

-

-

MSTAR

MSTAR

ST

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

-

-

Lola

Lola

Sequoia

Lola

Lola

Lola

Lola

Lola

Lola

Lola

Lola

Lola

Lola

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

0x33

0x34

0x35

0x36

0x37

0x38

0x39

0x3A

0x3B

0x3C

0x3D

0x3E

0x28

0x29

0x2A

0x2B

0x2C

0x2D

0x2E

0x2F

0x30

0x31

0x32

0x3F

0x40

0x41

0x42

0x43

SyncMaster 320MP-2


SyncMaster 400FP(n)-2


SyncMaster 460FP(n)-2

SyncMaster P42H-2

SyncMaster P50HP

SyncMaster P50FP

SyncMaster P63FP

SyncMaster 460Rn-S

SyncMaster 400DXn-S

SyncMaster 460DXn-S

SyncMaster 400CX(n)-2


SyncMaster 400DX(n)-2




SyncMaster 650MP(n)

SyncMaster 400UX(n)-2


SyncMaster 700DRn

SyncMaster 230TSn

SyncMaster 230MXn

SyncMaster 460DMn

SyncMaster 400UXn-UD2

SyncMaster 460UXn-UD2

SyncMaster P50HP-2

SyncMaster P63FP-2

SyncMaster 400EXn

SyncMaster 460EXn

SyncMaster 550EXn

SyncMaster 460UT(n)-2

SyncMaster 550DX(n)




SyncMaster 520LD



SyncMaster 400BX

SyncMaster 460TS(n)-3

SyncMaster 400TS(n)-3

SyncMaster 460UT(n)-UD2

MSTAR Lola

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

MSTAR

ST

Lola

Lola

Lola

Lola

Lola

Lola

Lola

Lola

Sequoia

-

-

-

-

-

-

-

-

-

-

ST Sequoia

ST

MSTAR

MSTAR

ST

MSTAR

MSTAR

ST

ST

ST

ST

ST

Sequoia

Lola

Lola

Sequoia

Lola

Lola

Mars

Mars

Mars

Mars

Mars

ST Mars

ST

ST

Mars

Mars

ST

ST

Mars

Mars

0x44

0x45

0x46

0x47

0x48

0x49

0x4A

0x4B

0x4C

0x4D

0x4E

0x4F

0x50

0x51

0x52

0x53

0x54

UE46A/UE55A

ME40A/ME46A/ME55A

DE40A/DE46A/DE55A

MD32B/MD40B/MD46B/MD55B

ME32B/ME40B/ME46B

ME55B/ME65B/ME75B

SL46B

SyncMaster UD55A

DE40C/DE46C/DE55C

UD46C/UD55C/

UE46C/UE55C/

SyncMaster UD22A

SyncMaster NL22B

MD32C, MD40C, MD46C, MD55C,

ME95C

ED32C/ED40C/ED46C/

ED55C/ED65C/ED75C/

ED32D/ED40D/ED46D/

ED55D/ED65D/ED75D/

SyncMaster LE32C

SyncMaster LE46C

SyncMaster LE55C

SyncMaster UD46C-B

ME32C/ME40C/ME46C/ME55C/

SyncMaster UD55C-B

DB22D/DB32D/DB40D/

DB48D/DB55D/DM32D/

OH46D/OH55D

DM40D/DM48D/DM55D

DM65D/DM75D

UE46D/UE55D

DH40D/DH48D/DH55D

OM46D/OM55D/OM75D

EB40D/EB48D

SyncMasterQM55D

SyncMasterQM85D

SyncMasterQM50D

SyncMasterQM40D

SyncMasterQM105D

EM65E/EM75E

ED65E/ED75E

DH40E,DH48E,DH55E

Samsung Genoa-P

Samsung Genoa-P

ST

Samsung

Mars

Echo-E

ACM12

ACM12

ST

ST

Samsung

Mars

Mars

Echo-P STDP7310

Novatek

ST

ST

Samsung

ST

Samsung

Samsung

Samsung

Samsung

Samsung

Novatek

Mstar

NT72569(N

T13)

Mars

Mars

Echo-E

Mars

Golf-S

Golf-S

Golf-S

Golf-S

Golf-S

NT72456(N

T14L)

SE13U

Novatek

Samsung

NT72456

(NT14L)

Golf-S

ACM12

ACM12

ACM12

0x55

0x56

DM32E,DM40E,DM48E,

DM55E,DM65E,DM75E

DB32E,DB40E,DB48E,DB55E

DM65E-BR, DM75E-BR, DM82E-BR

PE40E,PE46E,PE55E

DM10E, OHE, OME, MLE, SHF

UD46E-P, UD55E-P, UD55E-S

RH48E, RH55E

SyncMaster UD46E-B

SyncMaster UD55E-B

SyncMaster UD46E-C

IL015E/ IL025E

Samsung

Samsung

Samsung

Samsung

Samsung

Samsung

Samsung

Novatek

Golf-S

Golf-S

Golf-S

Golf-S

Golf-S

Golf-S

Golf-S

SE15HV

ACM

ACM

ACM12

0x57

Novatek NT14F

0x58

SBB-ES Samsung GOLF-S

0x59

0x5A

DC32E / DC40E / DC48E / DC55E

OM24E

OH24E/OH75E

SBB-MT

Novatek

NT72456

(NT14L)

Samsung Golf-S

Mstar SE13U

-

0x5B

0x5C

0x5D

0x5E

0x5F

0x60

0x61

0x62

0x63

0x64

0x65

DC32E-M / DC40E-M / DC48E-M /

DC55E-M

DC32E-H / DC40E-H / DC48E-H /

DC55E-H

QM49F / QM55F /QM65F /

QM75F / QM98F

PM32F / PM43F / PM49F / PM55F /

PH43F / PH49F / PF55F

OM46F / OM55F / OH46F / OH55F

DC90F

UH46F5

OH85F

DC43H / DC49H / DC55H

QMH / QHH / PMJ / PHJ / PBJ

IFH

Novatek

Mstar

NT72456

(NT14L)

SE13U

Samsung Hawk-MU

NONE

Samsung Hawk-MU

Novatek NT16L

Novatek

Mstar

SE15HV

SE13U

Novatek

Samsung

NT14L

Kant-M

NONE

ACM12

NONE

NONE

NONE

TI

Samsung

Novatek

AM3352

Kant-M

NT14L

None

NONE

0x66 OHH

0x67 RM49H

TV : TV / Monitor's TV support/not support.

0x00 Support TV 0x01

●

Nak

Header

0xAA

Command

0xFF

ID

Do not support TV

Data Length Ack/Nak

0x03 'N' r-CMD

0x10

Val 1

ERR

Check

Sum


2.1.11 Power Control

●

Function

Personal Computer turns TV / Monitor power ON/OFF.

●

Get Power ON/OFF Status


0xAA 0x11

ID

0x00

Check

Sum

●

Set Power ON/OFF

Header Command

ID

Data Length Data 1

0xAA 0x11 0x01 Power

Power : Power code to be set on TV / Monitor

0x00 Power OFF 0x01

Check

Sum

Power ON

Reboot 0x02

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'A' r-CMD

0x11

Power : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x11

Val 1

Power

Check

Sum

Val 1

ERR

Check

Sum


Note :

- When you execute power on function by RJ45 MDC then you must re-connect

a socket connection after 10 sec.

- When Monitor is Power Off status and connect by RJ45 Then you must transmit the WOL protocol instead of MDC protocol using TCP/IP Format for Power On.

(In "Network Standby : Off" Condition(DMD/DBD/DHD/UED/DMD-S) and always (Other Models)

- If you send a MDC Command for "PowerOn" or "PowerOff"

It must retry for 3 times every 2 Seconds until ACK command.

If there is no ACK within 3 times, It means failure.

Please refer below explanation

1) SET POWER OFF

0xAA,0x11,0x01,0x00,0x0x12 : MONITOR 1






2) SET POWER ON







2.1.12 Volume Control

●

Function

Personal Computer changes volume of TV / Monitor.

●

Get Volume Status


0xAA 0x12

ID

0x00

Check

Sum

●

Set Volume


ID

0xAA 0x12 0x01 Volume

Volume

: Volume value code to be set on TV/Monitor (0 ~ 100 )

Check

Sum

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x12

Volume : Same as above

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x12


Val 1

Volume

Val 1

ERR

Check

Sum

Check

Sum

2.1.13 Mute Control

●

Function

Personal Computer turns TV / Monitor mute ON/OFF.

●

Get Mute ON/OFF Status


0xAA 0x13

ID

0x00

Check

Sum

●

Set Mute ON/OFF


ID

0xAA 0x13 0x01

Mute

:

Mute code to be set on TV / Monitor

0x00 Mute OFF 0x01

Data 1

Mute

Check

Sum

Mute ON

●

Ack

Header Command

0xAA 0xFF

Mute : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

ID

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03 'N' r-CMD

0x13 r-CMD

0x13


Val 1

Mute

Val 1

ERR

Check

Sum

Check

Sum

2.1.14 Input Source Control

0x20

0x22

0x24

0x26

0x30

0x32

0x34

0x40

0x50

0x56

0x60

0x62

●

Function

Personal Computer changes input source of TV / Monitor.

●

Get Input Source Status


0xAA 0x14

ID

0x00

Check

Sum

●

Set Input Source

Header Command

0xAA 0x14

ID

Data Length

0x01

Input : Input Source code to be set on TV / Monitor

0x04 S-Video 0x08

Data 1

Input

0x0C

0x0E

0x14

0x1E

AV1 (AV)

Ext. (SCART1)

PC

BNC

0x0D

0x18

-

0x1F

Check

Sum

Component

AV2

DVI

-

DVI_VIDEO

Magicinfo

HDMI1_PC

HDMI2_PC

DispalyPort2

RF(TV)

HDMI3_PC

HDMI4_PC

TV (DTV)

Plug In Module

OCM

Media/MagicInfo S

Internal/USB

0x21

0x23

0x25

0x27

0x31

0x33

-

-

0x55

-

0x61

0x63

HDMI1

HDMI2

DispalyPort(DispalyPort1)

DispalyPort3

HDMI3

HDMI4

-

-

HDBaseT

-

WiDi/Screen Mirroring

URL Launcher

0x64 IWB 0x65 Web Browser

Note : DVI_VIDEO, HDMI1_PC, HDMI2_PC, HDMI3_PC, HDMI4_PC → Get Only

In the case of Magicinfo, only possible with models include Magicinfo.

In the case of TV, only possible with models include TV.

In case of AV2, Ext, only possible with models include AT2, Ext.

On Timer function, Do not use 0x61. and use 0x62 by Internal/USB

URL Launcher can be supported on DB/DM/DH/UE Model.

●

Ack

Header Command ID Data Length Ack/Nak r-CMD Val 1 Check

0xAA 0xFF

Input : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

0x03 'A'

Data Length Ack/Nak

0x03 'N'


0x14 r-CMD

0x14

Input

Val 1

ERR

Sum

Check

Sum

2.1.15 Picture Size Control

●

Function

Personal Computer changes Picture Size of TV / Monitor.

●

Working Condition

It will not work with Video Wall is On

●

Get Picture Size Status

Header Command

0xAA 0x15

ID

Data Length

0x00

Check

Sum

●

Set Picture Size

Header Command

0xAA 0x15

ID

Data Length

0x01

Data 1

Aspect

Check

Sum

Aspect : Picture Size code to be set on TV / Monitor

PC Mode Video Mode

0x10 16 : 9 0x00 Auto Wide

0x18

0x20

0x21

0x22

4 : 3

Original Ratio

21 : 9

Custom

0x01

0x04

0x05

0x06

0x09

0x0B

0x0C

0x0D

0x0E

0x0F

0x31

0x32

16 : 9

Zoom

Zoom1

Zoom2

Just Scan(Screen Fit)

4 : 3

Wide Fit

Custom

Smart View 1

Smart View 2

Wide Zoom

21 : 9

Note :

- Some of theimage sizes are not supported depending on input signals (720p, 1080i).

- For MFM model only possible for those include Europe TV if size is Auto Wide

- PC mode and Video mode definition

Product Type

(Defined in Model Number Control)

PC Mode Video Mode

0x01 ~ 0x4e,

0x51, 0x53, 0x59, 0x5c, 0x60

0x4f, 0x50, 0x52, 0x54, 0x55, 0x56, 0x5a,

0x61, 0x62

PC1, PC2, DVI, BNC,

HDMI_PC, DP

PIC_MODE_PC

AV, S-VIdeo, Component,

DVI_Video, HDMI_Video

PIC_MODE_VIDEO

0x5E Work as a PC Mode always

- Depends on each model specification, all or some of the picure size mode will be available.

●

Ack


0xAA 0xFF

ID

0x03 'A' 0x15 Aspect

Check

Sum

Aspect : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'


0x15

Val 1

ERR

Check Sum

2.1.17 Direct Channel Control (DTV)

●

Function

Personal Computer can control TV Channel.

Note : Only works with models include TV

●

Get Channel


ID

0xAA 0x17 0x00

●

Set Channel


ID

0xAA 0x17 0x08

Check

Sum

Data 1

Country

Data 2

ATV_DTV

Data 3

AirCable

Data 4

CH_NUM

(High)

Data 5

CH_NUM

(Low)

Data 6

Sel_Minor

Data 7

Minor_CH

(High)

Data 8

Minor_CH

(Low)

Check

Sum

●

Ack


ID

0xAA 0xFF 0x0A 'A' 0x17 Country ATV_DTV


AirCable

CH_NUM

(Hgh)

CH_NUM

(Low)

Sel_Minor

Minor_CH

(Hgh)

Minor_CH

(Low)

Check

Sum

Country : Select the country to be set on TV / Monitor (0 : Korea, 1: USA, .... )

ATV_DTV : Select Analog TV and DTV to be set on TV / Monitor ( 0 : Analog TV, 1: Digital TV)

AirCalbe : Select if TV is cabled or general ( 0 : general, 1: cabled)

CH_NUM : TV channel number to be set on TV / Monitor ( Analog TV : 1 ~ 135 , Digital TV : 0 ~ 999)

Sel_Minor : Select minor channel when DTV is to be set on TV / Monitor

( 0 : minor channel not selected. 1: minor channel selected.)

Minor_CH : Select minor channel number when DTV is to be set on TV / Monitor( 0 ~ 999.)

●

Nak


0xAA 0xFF

ID

0x03 'N' 0x17 ERR

Check

Sum


2.1.18 Screen Mode Control

●

Function

Personal Computer changes screen mode of TV

●

Working Condition

It will work on Video Wall Off, Landscape or Picture size is Auto Wide

Picture Size Auto Wide is only used on European Tuner Signal

●

Get Screen Mode Status


0xAA 0x18

ID

0x00

Check

Sum

●

Set Picture Size

Header Command

0xAA 0x18

ID

Data Length

0x01

Data 1

ScrMode

Check

Sum

ScrMode : Screen Mode Code to be set on TV / Monitor

0x01 16 : 9

0x04

0x0B

Zoom

4 : 3

●

Ack

0x31

Header

Wide Zoom

Command Data Length Ack/Nak

0xAA 0xFF

ScrMode : Same as above

●

Nak

Header Command

ID

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N' r-CMD

0x18 r-CMD

0x18

Val 1

ScrMode

Val 1

ERR

Check

Sum

Check

Sum

2.1.19 Screen Size Control

●

Function

Personal Computer recognizes the screen size of TV / Monitor.

●

Get Screen Size Status


0xAA 0x19

ID

0x00

Check

Sum

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'A' r-CMD

0x19

Val 1

Screen

Size

Screen Size : Screen size of TV / Monitor ( Range : 0 ~ 255, Unit : Inch )

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x19


Val 1

ERR

Check

Sum

Check

Sum

2.1.1D MDC Connection Type

●

Function

Personal Computer get MDC Connection Type of TV / Monitor.

Note : It is dependent on Product Specifications- RJ45 MDC Connection

It is Get Commnad Only.

●

Get MDC Connection Status


0xAA 0x1D

ID

0x00

Check

Sum

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x1D

Val 1

Connection

Type

Connection Type :

0x00 RS232C MDC

●

Nak

Header Command

ID

0xAA 0xFF

0x01

Data Length Ack/Nak

0x03

ERR

:

Error code that shows what occurred error is

'N'

RJ45 MDC r-CMD

0x1D

Val 1

ERR

Check

Sum

Check

Sum

2.1.24 Contrast Control

●

Function

Personal Computer changes contrast of TV / Monitor.

●

Working Condition

1. AV, S-Video, Component, DVI(HDCP) Only



It will not work with Calibration of picture mode in the menu

●

Get Contrast Status

Header Command

0xAA 0x24

●

Set Contrast

Header Command

0xAA 0x24

ID

ID

Data Length

0x00

Data Length

0x01

Check

Sum

Data 1

Contrast

Check

Sum

Contrast : Contrast value code to be set on TV/Monitor ( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x24

Contrast : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x24


Val 1

Contrast

Val 1

ERR

Check

Sum

Check

Sum

2.1.25 Brightness Control

●

Function

Personal Computer changes brightness of TV / Monitor.

●

Working Condition





●

Get Brightness Status

Header Command

0xAA 0x25

ID

Data Length

0x00

Check

Sum

●

Set Brightness


0xAA 0x25

ID

0x01 Brightness

Check

Sum

Brightness : Brightness value code to be set on TV/Monitor ( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x25

Brightness : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0 'N' r-CMD

0x25

Val 1

Brightness

Val 1

ERR

Check

Sum

Check

Sum


2.1.26 Sharpness Control

●

Function

Personal Computer changes sharpness of TV / Monitor.

●

Working Condition





●

Get Sharpness Status

Header Command

0xAA 0x26

ID

Data Length

0x00

Check

Sum

●

Set Sharpness


0xAA 0x26

ID

0x01 Sharpness

Check

Sum

Sharpness : Sharpness value code to be set on TV/Monitor ( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x26

Sharpness : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x26


Val 1

Sharpness

Val 1

ERR

Check

Sum

Check

Sum

2.1.27 Color Control

●

Function

Personal Computer changes the color of TV / Monitor.

●

Working Condition


2. A product which has **** Text , **** Video/Image and Calibration as picture mode, it will not affect by the 1st condition and instead,


●

Get Color Status

Header Command

0xAA 0x27

ID

Data Length

0x00

Check

Sum

●

Set Color


ID

0xAA 0x27 0x01 Color

Color : Color value code to be set on TV/Monitor( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A'

Color : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


Check

Sum r-CMD

0x27 r-CMD

0x27

Val 1

Color

Val 1

ERR

Check

Sum

Check

Sum

2.1.28 Tint Control

●

Function

Personal Computer changes tint of TV / Monitor when visual display is NTSC.

●

Working Condition


2. A product which has **** Text , **** Video/Image and Calibration as picture mode, it will not affected by the 1st condition and instead,


●

Get Tint Status

Header Command

0xAA 0x28

ID

Data Length

0x00

Check

Sum

●

Set Tint


0xAA 0x28

ID

0x01 Tint

Check

Sum

Tint : Tint value code to be set on TV/Monitor (0 ~ 100 )

R Tint Value

G ( 100 - Tint ) Value

Note : Tint could only be set in 50 Steps ( 0, 2, 4, 6... 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A'

Tint : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


0x28 r-CMD

0x28

Val 1

Tint

Val 1

ERR

Check

Sum

Check

Sum

2.1.2F Coarse Control

●

Function

Personal Computer adjusts Coarse of TV / Monitor.

●

Working Condition

- PC(D-Sub), BNC Only

- It will not work in case of Videowall is On

●

Get Coarse Status

None

●

Set Coarse


ID

0xAA 0x2F 0x01 Coarse

Check

Sum

Coarse : Coarse Increase/Decrease code to be set on TV/Monitor

0x00 Decrease 0x01 Increase

●

Ack

Header Command

ID


0xAA 0xFF 0x03 'A' 0x2F

Coarse : Same as above

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x2F


Val 1

Coarse

Val 1

ERR

Check

Sum

Check

Sum

2.1.30 Fine Control

●

Function

Personal Computer adjusts Fine of TV / Monitor.

●

Working Condition


- It will not work in case of Videowall is On

●

Get Fine Status

None

●

Set Fine


ID

0xAA 0x30 0x01

Data 1

Fine

Check

Sum

Fine : Phase Increase/Decrease code

0x00 Decrease

●

Ack

Header Command

ID

0x01 Increase


0xAA 0xFF 0x03 'A' 0x30

Fine : Same as above

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x30


Val 1

Fine

Val 1

ERR

Check

Sum

Check

Sum

2.1.31 H-Position Control

●

Function

Personal Computer adjusts Horizontal Position of TV / Monitor.

●

Working Condition


- When Video Wall is on or Zoom (0x39) is set, you can not control

●

Get H-Position Status

None

●

Set H-Position


0xAA 0x31

ID

0x01 H-Pos

Check

Sum

H-Pos : H-Position Increase/Decrease code to be set on TV/Monitor

0x00 Move to Left 0x01 Move to Right

●

Ack

Header Command

ID


0xAA 0xFF 0x03 'A' 0x31

H-Pos : Same as above

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x31


Val 1

H-Pos

Val 1

ERR

Check

Sum

Check

Sum

2.1.32 V-Position Control

●

Function

Personal Computer adjusts Vertical Position of TV/Monitor.

●

Working Condition



●

Get V-Position Status

None

●

Set V-Position


0xAA 0x32

ID

0x01 V-Pos

Check

Sum

V-Pos : V-Position Increase/Decrease code to be set on TV/Monitor

0x00 Move Up 0x01 Move Down

●

Ack

Header Command

ID

Data Length Ack/Nak

0x03 'A' r-CMD

0x32 0xAA 0xFF

V-Pos : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x32


Val 1

V-Pos

Val 1

ERR

Check

Sum

Check

Sum

2.1.33 Auto Power

●

Function

Personal Computer adjusts Auto Power Control of TV/Monitor.

●

Get Auto Power


0xAA 0x33

ID

0x00

Check

Sum

●

Set Auto Power


ID

0xAA 0x33 0x01 Auto Power

Check

Sum

Auto Power : The Auto Power Control code to set for the TV or monitor

0x00 Auto Power Off 0x01 Auto Power On

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x33

Auto Power : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x33

Val 1

Auto Power

Val 1

ERR


Check

Sum

Check

Sum

2.1.34 Clear Menu Control

●

Function

Personal Computer removes Menu OSD left in TV / Monitor.

●

Get Clear Menu Status

None

●

Set Clear Menu


ID

0xAA 0x34 0x01 Clear

Clear : 0x00 (Always)

●

Ack


ID

0xAA 0xFF

Clear : Same as above

●

Nak

Header Command

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03 'N'


Check

Sum r-CMD

0x34 r-CMD

0x34

Val 1

Clear

Val 1

ERR

Check

Sum

Check

Sum

2.1.36 Remote Control

●

Function

Personal Computer enables/disables IR receiving function of TV/Monitor/

●

Working Condition

- Can operate regardless of whether power is ON/OFF

(If DPMS Situation in LFD, it operate Remocon regardless of set value.)

●

Get IR Lock Status


0xAA 0x36

ID

0x00

Check

Sum

●

Set IR Lock


0xAA 0x36

ID

0x01 RMC

Check

Sum

RMC : Power code to be set on TV/Remocon

0x00 Remocon Disable 0x01

●

Ack

Header Command

ID

Remocon Enable

Data Length Ack/Nak

0x03 'A' r-CMD

0x36 0xAA 0xFF

RMC : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x36


Val 1

RMC

Val 1

ERR

Check

Sum

Check

Sum

2.1.37 RGB Contrast Control

●

Function

Personal Computer changes contrast of TV / Monitor

●

Working Condition





●

Get Contrast Status


0xAA 0x37

ID

0

Check

Sum

●

Set Contrast

Header Command

ID

Data Length Data 1

Check

Sum

0xAA 0x37 0x01 Contrast

Contrast : RGB Contrast value code to be set on TV/Monitor ( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x37

Contrast : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x37


Val 1

Contrast

Val 1

ERR

Check

Sum

Check

Sum

2.1.38 RGB Brightness Control

●

Function

Personal Computer changes Brightness of TV / Monitor

●

Working Condition





●

Get Brightness Status


0xAA 0x38

ID

0x00

Check

Sum

●

Set Brightness

Header Command

ID

Data Length Data 1

Check

Sum

0xAA 0x38 0x01 Brightness

Brightness : RGB Brightness value code to be set on TV/Monitor ( 0 ~ 100 )

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x38 Brightness

Brightness : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x38

Val 1

ERR


Check

Sum

Check

Sum

2.1.3C PIP On/Off Control

●

Function

The PC turns the PIP function of a TV or monitor on/off.

●

Working Condition

- This does not operate in MagicNet mode.

- When Video Wall is On, you can not control.

●

Get PIP ON/OFF Status


0xAA 0x3C

ID

0x00

Check

Sum

●

Set PIP ON/OFF


ID

0xAA 0x3C 0x01 PIP

Check

Sum

PIP : The PIP On/Off code to set for the TV or monitor.

0x00 PIP OFF 0x01

●

Ack

Header Command

ID

PIP ON

Data Length Ack/Nak


0x3C

PIP : Same as above.

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x3C

ERR : The error code indicating which error occurred.

Val 1

PIP

Val 1

ERR

Check

Sum

Check

Sum

2.1.3D Auto Adjustment Control

●

Function

Personal Computer controls PC system screen automatically.

●

Working Condition


- In case of videlwall is on or picture size is Zoom, it will not work

●

Get Auto Adjustment Status

None

●

Set Auto Adjustment


0xAA 0x3D

ID

0x01 Auto

Check

Sum

Auto : 0x00 (Always)

●

Ack


ID

0xAA 0xFF

Auto : Same as above

●

Nak

Header Command

0x03 'A'

Data Length Ack/Nak

0x3D r-CMD

ID

0xAA 0xFF 0x03 'N' 0x3D


Val 1

Auto

Val 1

ERR

Check

Sum

Check

Sum

2.1.3E Color Tone Control

●

Function

Personal Computer changes Color Tone of TV / Monitor.

●

Working Condition


It will work with **** Video/Image of picture mode in the menu

●

Get Color Tone Status


0xAA 0x3E

ID

0x00

Check

Sum

●

Set Color Tone

Header Command

ID

Data Length Data 1

Check

Sum

0xAA 0x3E 0x01 Color Tone

Color Tone : Color Tone value code to be set on TV/Monitor ( 0 ~ 4 )

0x00 Cool 2

0x01

0x02

0x03

0x04

Cool 1(Cool)

Normal(Standard)

Warm 1(Warm)

Warm 2

0x50 Off

●

Ack

Header Command

ID

0xAA 0xFF

Color Tone : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03 'N' r-CMD

0x3E r-CMD

0x3E

Val 1

Color Tone

Val 1

ERR

Check

Sum

Check

Sum


2.1.3F Color Temperature Control

●

Function

Personal Computer changes Color Temperature value of TV / Monitor.

●

Working Condition

1. Only operates when Color Tone is set to Off.


- It will not work in case of PIC_MODE is PIC_MODE_CALIB

* For the PIC_MODE definition pls refer AnnexB

●

Get Color Temperature


0xAA 0x3F

ID

0x00

Check

Sum

●

Set Color Temperature


0xAA 0x3F

ID

0x01

C_Temp

( or

Extended)

Check

Sum

C_Temp : Color Temperature value code to be set on TV/Monitor

0x00 ~

0x0a

5000K ~ 15000K

0xFD

0xFE

0xFF

2800K

3000K

4000K

C_Temp (Extended) : Color Temperature value code to be set on TV/Monitor

28(0x1c) 2800K 95(0x5f) 9500K

30(0x1e) 3000K 100(0x64) 10000K

35(0x23)

40(0x28)

45(0x2d)

50(0x32)

55(0x37)

60(0x3c)

65(0x41)

70(0x46)

75(0x4b)

80(0x50)

85(0x55)

90(0x5a)

3500K

4000K

4500K

5000K

5500K

6000K

6500K

7000K

7500K

8000K

8500K

9000K

105(0x69)

110(0x6e)

115(0x73)

120(0x78)

125(0x7d)

130(0x82)

135(0x87)

140(0x8c)

145(0x91)

150(0x96)

155(0x9b)

160(0xa0)

10500K

11000K

11500K

12000K

12500K

13000K

13500K

14000K

14500K

15000K

15500K

16000K

Note : Depends on each model spec, it will work for the both of C_Temp and C_Temp (Extended) but in case of get it will returns as C_Temp (Extended)

●

Ack


0xAA 0xFF

ID

0x03 'A' 0x3F C_Temp

Check

Sum

C_Temp : Same as above

●

Nak


0xAA 0xFF

ID

0x03 'N' 0x3F ERR

Check

Sum


2.1.40 PIP Source Control

●

Function

The PC changes the PIP source of a TV or monitor.

●

Working Condition

- This only operates for a TV or monitor where PIP is set to On.


●

Get PIP Source Status


0xAA 0x40

ID

0x00

Check

Sum

●

Set PIP Source

Header Command

0xAA 0x40

ID

Data Length

0x01

Data 1

P.Source

Check

Sum

P.Source

: The input source code to set for the TV or monitor.

Note : The PIP source swap may not function according to the main source.

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x40 P.Source

P.Source

: Same as above.

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x40 ERR

Check

Sum

Check

Sum


2.1.42 PIP Size Control

●

Function

The PC changes the PIP size of a TV or monitor.

●

Working Condition


●

Get PIP Size Status


ID

0xAA 0x42 0x00

●

Set PIP Size


ID

0xAA 0x42 0x01

Check

Sum

Data 1

P.Size

P.Size

: The PIP size code set for the TV or monitor.

0x00 PIP Off

0x04

0x05

0x06

0x07

0x08

0x09

0x10

Double 1(Doble Window)

Double 2(Double Wide)

Medium

Large

Small

Double 3(POP)

Custom

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'A'

P.Size

: Same as above.

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'


Check

Sum r-CMD

0x42 r-CMD

0x42

Val 1

P.Size

Val 1

ERR

Check

Sum

Check

Sum

2.1.43 PIP Locate Control

●

Function

The PC adjusts the PIP position of a TV or monitor.

●

Working Condition

- This does not operate in MagicInfo mode.

- Only TV / Monitor that PIP is On Can use this command.

●

Get PIP Locate Status


0xAA 0x43

ID

0x00

Check

Sum

●

Set PIP Locate

Header Command

ID

Data Length Data 1

0xAA 0x43 0x01 P.Locate

Check

Sum

P.Locate

: The PIP Locate Increase/Decrease code to set for the TV or monitor.

0x00 PIP Off(Get Only)

0x01

0x02

0x03

0x04

●

Ack

Header

0xAA

Upper Left

Upper Right

Lower Right

Lower Left

Command

0xFF

ID

Data Length Ack/Nak

0x03 'A' r-CMD

0x43

Val 1

P.Locate

P.Locate

: Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'

ERR : The error code indicating which error occurred. r-CMD

0x43

Val 1

ERR

Check

Sum

Check

Sum

2.1.44 Fan Speed Setting

●

Function

The PC adjusts the Fan Speed of a TV or monitor.

●

Get Fan Speed


ID

0xAA 0x44 0x00

Check

Sum

●

Set Fan Speed


ID

0xAA 0x44 0x01 FAN Speed

Check

Sum

FAN Speed : The Fan Speed to set for the TV or monitor.(0 ~ 100)

Note : If you send "Set Fan speed", then "Fan Control" changed "Manual".

(refer "Fan Control" command (0x8F))

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x44

Val 1

FAN Speed

FAN Speed : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x44

Val 1

ERR


Check

Sum

Check

Sum

2.1.45 User Auto Color

●

Function

The PC adjusts the User Auto Color Control of a TV or monitor.

Note : It is dependent on Product Specifications.

●

Working Condition

- PC(D-Sub) Only

- It will support only Scaler model

●

Get User Auto Color

It will return NAK always

●

Set User Auto Color


0xAA 0x45

ID

0x01

Auto Color

Cmd

Check

Sum

Auto Color Cmd : The Auto Color Cmd to set for the TV or monitor.

0x00 Reset 0x01 Auto Color

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x45

Auto Color Cmd : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'

ERR : The error code indicating which error occurred. r-CMD

0x45

Val 1

Auto Color

Cmd

Val 1

ERR

Check

Sum

Check

Sum

2.1.47 Sound Select Control

●

Function

The PC changes the sound when the PIP of a TV or monitor is set to On.

Note : Same function is also exist on 0x65

●

Get the Sound Select


0xAA 0x47

ID

0x00

Check

Sum

●

Set the Sound Select


0xAA 0x47

ID

0x01 S.Selct

Check

Sum

S.Select

: The Sound Select code to set for the TV or monitor

0x00 Sub 0x01 Main

●

Ack

Header Command

ID

Data Length Ack/Nak


0x47

S.Select

: Same as above.

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x47

Val 1

S.Select

Val 1

ERR


Check

Sum

Check

Sum

2.1.48 Auto Volume Control

●

Function

The PC changes the Auto Volume.

●

Get Auto Volume

Header Command

ID

0xAA 0x48

●

Set Auto Volume

Header Command

ID

0xAA 0x48

Data Length

0x00

Data Length

Check

Sum

Data 1

0x01 A_VOL

A_VOL : The Auto Volume code to set for the TV or monitor.

0x00 OFF

0x01

0x02

●

Ack

Header

Normal(On)

Night


0xAA 0xFF

A_VOL : Same as above

●

Nak

Header Command

ID

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N'

Check

Sum r-CMD

0x48 r-CMD

0x48

Val 1

A_VOL

Val 1

ERR

Check

Sum

Check

Sum

2.1.4A Standby Control

●

Function

The PC adjusts the Standby Control of a TV or monitor.

●

Working Condition

It is work for PC/DVI/HDMI/DisplayPort.

●

Get Standby Setting


ID

0xAA 0x4A

●

Set Standby Setting

0x00

Check

Sum


ID

0xAA 0x4A 0x01

Standby

Setting

Check

Sum

Standby Setting : The Standyby Setting code to set for the TV or monitor

0x00 Off

0x01 On

Auto

●

Ack

0x02


ID

0xAA 0xFF 0x03 'A' 0x4A

Val 1

Standby

Setting

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x4A ERR


Check

Sum

Check

Sum

2.1.4B Video Picture Position & Size

●

Function

The PC adjusts the Picture Position & Size of a TV or monitor.

●

Working Condition

1. Video Source Only


it will not affect by the 1st condition and instead,

- It will work in case of PIC_MODE is PIC_MODE_VIDEO


3. And "Picture Size" is must be zoom1,zoom2, Screen Fit, Custom.

Other Picture sizes doesn't support this function.

(For detail, plase refer below table.)

Reset

Position Size

0x00 0x01 0x02 0x03 0x00 0x01 0x02 0x03

Zoom1

Zoom2

O

O

O

O

O

O

X

X

X

X

X

X

X

X

X

X

X

X

Screen Fit O O O O O X X X X

O

X

Custom O O O O O O O O

Zoom O O O

●

Get Video Picture Position & Size

It will return NAK always

●

Set Video Picture Position & Size

X X X X X


0xAA 0x4B

ID

0x02

Type

CMD

Direction

CMD

Type CMD : The Standyby Setting code to set for the TV or monitor

0x00 Reset 0x01 Position

0x02 Size 0x03 RESERVED

Direction CMD: It is work for Type CMD Size or Position.

If "Type CMD" is Reset, then "Direction CMD" is not work.

Direction CMD(Position) Direction CMD(Size)

0x00 Down 0x00 Vertical Scale Down

0x01

0x02

0x03

Up

Left

Right

0x01

0x02

0x03

Vertical Scale Up

Horizontal Scale Down

Horizontal Scale Up

Check

Sum

●

Ack

Header Command ID Data Length Ack/Nak r-CMD Val 1 Val 2

0xAA 0xFF 0x04 'A'

Check

Sum

Type CMD, Direction CMD : Same as Above

●

Nak


ID

0xAA 0xFF 0x03 'N'


0x4B Type CMD

Direction

CMD r-CMD

0x4B

Val 1

ERR

Check

Sum

2.1.4C Pixel Shift Control

●

Function

Personal Computer controls Pixel Shift function of TV / Monitor.

●

Working Condition

-

When Video Wall is on or Zoom (0x39) is set or

DVI's Input Signal set VESA Mode, you can not control

●

Get Pixel Shift Status


0xAA 0x4C

ID

0x00

Check

Sum

●

Set Pixel Shift

Header Command

ID

Data Length Data 1 Data 2

0xAA 0x4C 0x04 Shift H.Dot

Data 3

V.Line

Check

Sum

Shift : Pixel Shift On/Off Code to be set on TV/Monitor

Note : If Shift value is off, H.Dot, V.Line, S.Time values are ignored in TV / Monitor.

0x00 OFF 0x01 ON

H.Dot

: Horizontal Dot value code set on TV/Monitor (0 ~ 4)

V.Line

: Vertical Line value code set on TV/Monitor (0 ~ 4)

S.Time

: Shift Time value code set on TV/Monitor (1 ~ 4)

●

Ack

Header Command

ID

Data Length Ack/Nak


0x4C

Val 1

Shift

Val 3 Val 4

Check

Sum

V.Line

S.Time

Shift, H.Dot, V.Line, S.Time

: Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


0x4C

Val 1

ERR

Data 4

S.Time

Val 2

H.Dot

Check

Sum

2.1.51 EQ 100Hz Control

●

Function

Personal Computer controls 100Hz field of Equalizer in TV / Monitor.

●

Get EQ 100Hz Status


0xAA 0x51

ID

0

Check

Sum

●

Set EQ 100Hz


0xAA 0x51

ID

0x01 100Hz

Check

Sum

100Hz :

100Hz feild data among Equalizer set up in TV/Monitor

(0~20)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x51

100Hz : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x51


Val 1

100Hz

Val 1

ERR

Check

Sum

Check

Sum

2.1.52 EQ 300Hz Control

●

Function

Personal Computer controls 300Hz field of Equalizer in TV / Monitor.

●

Get EQ 300Hz Status


0xAA 0x52

ID

0x00

Check

Sum

●

Set EQ 300Hz


0xAA 0x52

ID

0x01 300Hz

Check

Sum

300Hz :

300Hz feild data among Equalizer set up in TV/Monitor

(0~20)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x52

300Hz : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x52


Val 1

300Hz

Val 1

ERR

Check

Sum

Check

Sum

2.1.53 EQ 1kHz Control

●

Function

Personal Computer controls 1KHz field of Equalizer in TV / Monitor.

●

Get EQ 1kHz Status


0xAA 0x53

ID

0x00

Check

Sum

●

Set EQ 1kHz


0xAA 0x53

ID

0x01 1kHz

Check

Sum

1kHz :

1KHz feild data among Equalizer set up in TV/Monitor

(0~20)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x53

1kHz : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x53


Val 1

1kHz

Val 1

ERR

Check

Sum

Check

Sum


●

Fuction


●

Get EQ 3kHz Status


0xAA 0x54

ID

0x00

Check

Sum

●

Set EQ 3kHz


0xAA 0x54

ID

0x01 3kHz

Check

Sum

3kHz :


(0~20)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x54


●

Nak


ID

0xAA 0xFF 0x03 'N' 0x54


Val 1

3kHz

Val 1

ERR

Check

Sum

Check

Sum


●

Function


●

Get EQ 10kHz Status


0xAA 0x55

ID

0x00

Check

Sum

●

Set EQ 10kHz


0xAA 0x55

ID

0x01 10kHz

Check

Sum

10kHz :


(0~20)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x55


●

Nak


ID

0xAA 0xFF 0x03 'N' 0x55


Val 1

10kHz

Val 1

ERR

Check

Sum

Check

Sum

2.1.57 Auto Lamp Control

●

Function

Personal Computer sets Auto Lamp Function of TV / Monitor.

Note :When Manual Lamp Control is on, Auto Lamp Control will automatically turn off.

●

Get Auto Lamp


0xAA 0x57

ID

0x00

Check

Sum

●

Set Auto Lamp

Header Command

ID

Data Length Data 1 Data 2 Data 3

0xAA 0x57 0x08 LMax_H LMax_M

Data 4

LMax_AP LMaxValue

Data 5

LMin_H

Data 6

LMin_M

Data 7 Data 8

LMin_AP LMinValue

Check

Sum

LMax_H : Auto Lamp Max Time Hour set on TV/Monitor (1 ~ 12)

LMax_M : Auto Lamp Max Time Minute set on TV/Monitor (0 ~ 59)

LMax_AP : Auto Lamp Max Time set on TV/Monitor AM/PM (AM :1 / PM:0)

LMaxValue : Auto Lamp Max Value set on TV/Monitor (0 ~ 100)

LMin_H : Auto Lamp Min Time Hour set on TV/Monitor (1 ~ 12)

LMin_M : Auto Lamp Min Time Minute set on TV/Monitor (0 ~ 59)

LMin_AP : Auto Lamp Min Time set on TV/Monitor AM/PM (AM :1 / PM:0)

LMinValue : Auto Lamp Min Value set on TV/Monitor (0 ~ 100)

Note : When LMinValue is returned to 0xFF, Auto Lamp Control is off.

When Dynamic contrast is On, Auto Lamp Control does not operate.

●

Ack

Header Command

ID


0xAA 0xFF 0x0A 'A' 0x57 LMax_H

Val 2

LMax_M

Val 3 Val 4 Val 5

LMax_AP LMaxValue LMin_H


●

Nak

Header Command

ID

0xAA 0xFF

Val 6

LMin_M

Data Length Ack/Nak

3


Val 7 Val 8

LMin_AP LMinValue

'N' r-CMD

0x57

Check

Sum

Val 1

ERR

Check

Sum

2.1.58 Manual Lamp Control

●

Function

Personal Computer sets Manual Lamp Function of TV / Monitor.

Note : When Auto Lamp Control is on, lamp value can be changed based on lamp schedule setting.

●

Get Manual Lamp Status


0xAA 0x58

ID

0x00

Check

Sum

●

Set Manual Lamp


0xAA 0x58

ID

0x01 LampValue

Check

Sum

LampValue : Manual Lamp value to be set on TV/Monitor (0 ~ 100)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x58

Val 1

LampValue

LampValue : Same as above

Note : When LampValue is returned as 0xFF, that means gotten value is invalid.

When Dynamic contrast is on, Manual Lamp Control does not operate.

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x58 ERR

Check

Sum

Check

Sum


2.1.59 Safety Screen Run Control

●

Function

Personal Computer will make Safety Screen function to operate immediately, not by Timer operation.

●

Get Safety Screen Run Status

Header Command

ID

0xAA 0x59

Data Length

0x00

Check

Sum

●

Set Safety Screen Run


0xAA 0x59

ID

0x01

Safety

Screen

Type

Check

Sum

Safety Screen Type : Safety Screen Type to be set on TV/Monitor (1~6)

0x00 Off

0x01 Signal Pattern

0x02

0x03

0x04

0x06

All White

Scroll

Bar

Eraser

0x07

...

0x10

Pixel

Rolling Bar

0x11 Fading Screen

Note : 1(0x01), 2(0x02) only works with PDP models

●

Ack


0xAA 0xFF

ID

0x03 'A' 0x59

Val 1

Safety

Screen

Type

Check

Sum

Safety Screen Type : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x59

Val 1

ERR

Check

Sum


2.1.5A Inverse Control

●

Function

Personal Computer Set Inverse On/Off.

●

Get Inverse Status


ID

0xAA 0x5A 0x00

●

Set Inverse


ID

0xAA 0x5A 0x01

Check

Sum

Data 1

Inverse

Check

Sum

Inverse : Inverse On/Off Code to be set on TV/Monitor

0x00 OFF 0x01

●

Ack


ID

0xAA 0xFF 0x03 'A'

ON r-CMD

0x5A

Inverse : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x5A


Val 1

Inverse

Val 1

ERR

Check

Sum

Check

Sum

2.1.5B Safety Screen Control

●

Function

Personal Computer sets Screen Burn Protection Timer of TV/Monitor.

●

Get Safety Screen Status


0xAA 0x5B

ID

0x00

Check

Sum

●

Set Safety Screen

When the Timer is Repeat


ID

0xAA 0x5B 0x03 Type T.Period

When the Timeris Interval


0xAA 0x5B

ID

0x07 Type

Data 3

T.Time

Data 2

StartTime-

Hour

Data 3

StartTime-

Min.

Data 5

EndTime

-Hour

Data 6

EndTime

-Min.

Data 7

EndTime

-am/pm

Check

Sum

Type :Timer type to set TV / Monitor

Note :

- If the valueix 0x00, means timer is off.(It dosen’t matter the length 3/7)

- If the value is not 0x00 and the MSB is 00 means timer type is Repeat and the MSB is 1 means timer type is interval

- If the command has make like below condition, it will be get ACK

(1) Data Length is 3 and timer typeis Interval

(2) Data Length is 7and timer type is Repeat

0x00 OFF 0x00 OFF

... ...

0x03

0x04

0x05

0x06

0x09

0x0A

...

Scroll

(Timer : Repeat)

Pixel

(Timer : Repeat)

Bar

(Timer : Repeat)

Eraser

(Timer : Repeat)

All White

(Timer : Repeat)

Pattern

(Timer : Repeat)

0x83

0x84

0x85

0x86

0x89

0x8A

...

Scroll

(Timer : Interval)

Pixel

(Timer : Interval)

Bar

(Timer : Interval)

Eraser

(Timer : Interval)

All White

(Timer : Interval)

Pattern

(Timer : Interval)

Check

Sum

Data 4

StartTimeam/pm

0x10

Rolling Bar

(Timer : Repeat)

0x90

Rolling Bar

(Timer : Interval)

0x11

Fading Screen

(Timer : Repeat)

0x91

Fading Screen

(Timer : Interval)

Note : 9(0x09), 10(0x0A)는 PDP 모델에서만 동작한다.

T.Period

: Timer periode hour data to set TV / Monitor (1 ~ 10 Hr.)

T.Time

:Timer periode code to set TV / Monitor (10 ~ 50 sec.)

0x01 10 sec

0x02

0x03

0x04

0x05

20 sec

30 sec

40 sec

50 sec

Note : If the timer type is Rolling Bar or Fading Scree, timer will work only 1 cycleregardless it’s type

If the timer periode is 0 or timer time is 0, timer will turn off

(IF the timer type is Rolling Bar or Fading Scree it will not turns off)

Start Time-Hour : The value of Start Time Hour (1 ~ 12)

Start Time-Min : The value of Start Time Minute ( 0 ~ 59 )

Start Time-am/pm : The value of Start Time AM/PM (1 : AM, 0 : PM)

End Time-Hour : The value of End Time Hour ( 1 ~ 12 )

End Time-Min : The value of End Time Minute 값 ( 0 ~ 59 )

End Time-am/pm : The value of End Time AM/PM (1 : AM, 0 : PM)

●

Ack

When the Timer is Repeat

Header Command

ID

Data Length Ack/Nak r-CMD Val 1 Val 2

0xAA 0xFF 0x05 'A' 0x5B Type T.Period

Val 3

Check

Sum

T.Time

Type, T.Period, T.Time : Same as above

When the Timeris Interval


ID


0x5B

Val 1

Type

Val 2

StartTime-

Hour

Val 3 Val 4 Val 5

End Time-

Hour

Val 6

End Time-

Min

Val 7

End Timeam/pm

Check

Sum

StartTime-

Min

StartTimeam/pm

Val 1 ~ Val 7 : 상동

●

Nak


0xAA 0xFF

ID

0x03 'N' 0x5B ERR

Check

Sum


2.1.5C Video Wall Mode Control

●

Function

Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON.

●

Working Condition

- Only works with TV/Monitor where Video Wall is on.

- Does not operate in MagicNet.

●

Get Video Wall Mode


0xAA 0x5C

ID

0x00

Check

Sum

●

Set Video Wall Mode


0xAA 0x5C

ID

0x01 WallMode

Check

Sum

WallMode : Video Wall Mode code to be set on TV/Monitor

0x00 Natural 0x01 Full

●

Ack

Header Command

ID

Data Length Ack/Nak


0x5C

WallMode : same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x5C

Val 1

WallMode

Val 1

ERR


Check

Sum

Check

Sum

2.1.5D Safety Lock

●

Function

Personal Computer turns Safety Lock function of TV/Monitor On/Off.

Note :Can operate regardless of whether power is on/off.

●

Get Safety Lock Status


0xAA 0x5D

ID

0x00

Check

Sum

●

Set Safety Lock Enable/Disable

Header Command

ID

0xAA 0x5D

Data Length

0x01

Data 1

Lock

Check

Sum

Lock : Lock code to be set on TV/Monitor

0x00 Off 0x01

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x03 'A'

On r-CMD

0x5D

Lock : Same as above

●

Nak

Header Command

ID


0xAA 0xFF 0x03 'N' 0x5D


Val 1

Lock

Val 1

ERR

Check

Sum

Check

Sum

2.1.5F Panel Lock

●

Function

Personal Computer turns Panel function Key Lock of TV/Monitor On/OFF.

Note : Can operate regardless of whether power is on/off.

●

Get Button Lock Status


0xAA 0x5F

ID

0x00

Check

Sum

●

Set Button Lock


0xAA 0x5F

ID

0x01 ButtonLock

Check

Sum

Button Lock : Panel Key Lock On/Off code to be set on TV/Monitor

0x00 Unlock 0x01 Lock

●

Ack


ID


Button Lock : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x5F


Val 1

ButtonLock

Val 1

ERR

Check

Sum

Check

Sum

2.1.61 Channel Up/Down

●

Function

Personal Computer can control TV Channel.

Note : If PIP is on and pip source is TV, it also should work.

Only works with models include TV.

●

Set TV Channel Up/Down


ID

0xAA 0x61 0x01

Channel

Up/Down

Check

Sum

Channel Up/Down : Channel UP or Down to be set on TV / Monitor (0~1)

0x00 Up 0x01 Down

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x61

Val 1

Channel

Up/Down

Channel Up/Down : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03


'N' r-CMD

0x61

Val 1

ERR

Check

Sum

Check

Sum

2.1.62 Volume Up/Down

●

Function

Personal Computer changes volume of TV / Monitor.

●

Get Volume Up/Down Status

Nothing

●

Set Volume Up/Down


ID

0xAA 0x62 0x01

Volume

Up/Down

Check

Sum

Volume Up/Down : Volume UP or Down to be set on TV / Monitor ( 0 ~ 100 )

0x00 Up 0x01 Down

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x62

Volume

Up/Down

Volume Up/Down : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x62

Val 1

ERR

ERR : Error Code showing what occurred error is.

Check

Sum

Check

Sum

2.1.63 Ticker

●

Function

Personal Computer control the ticker of LFD

●

Get Ticker Status


ID

0xAA 0x63 0x00

●

Set Ticker


ID

0xAA 0x63 Length

Check

Sum

Data 1

Ticker

On/Off

Data 2 Data 3

Start Hour Start Minute

Data 4

Start

AM/PM

Data 5

End Hour End Minute End AM/PM

Data 13

Data 6

Data 14

Data 7

Data 15

Data 8

Position

Horizontal

Data 16

Font Size

Data 9

Position

Vertical

Data 17

Foreground

Color

Background

Color

Foreground

Opacity

Background

Opacity

Data 10

Motion

On/Off

Data 18

Message

Date 1

Data 11

Motion

Direction

Data 19

Message

Date 2

Data 12

Motion

Speed

Data 20

Message

Date 3

Data 21 Data 22 Data N

Message

Date 4

...

Message

Date N

Check

Sum

Length : It means the variable length of data that is going to be sent.

You can set it differently depending on the length of message data and you need to input messages according to length that already set. ( 0 ~ 128 )

Ticker On/Off :Ticker's On/Off Code that is going to be set in TV / Monitor( 0 ~ 1 )

0x00 Ticker Off 0x01 Ticker On

Start Hour : The value of Start Time Hour that operate Ticker in TV / Monitor ( 1 ~ 12 )

Strat Minute : The value of Start Time Minute that operate Ticker in TV / Monitor ( 0 ~ 59 )

Start AM/PM : Start Time AM/PM that operate Ticker in TV / Monitor( 0 ~ 1 )

0x00 PM 0x01 AM

End Hour : The value of End Time Hour that operate Ticker in TV / Monitor( 1 ~ 12 )

End Minute : The value of End Time Minute that operate Ticker in TV / Monitor ( 0 ~ 59 )

End AM/PM : End Time AM/PM that operate Ticker in TV / Monitor( 0 ~ 1 )

0x00 PM 0x01 AM

Position Horizontal : Value of horizontal position of message that is presented in TV / Monitor (0 ~ 2)

Position Vertical : The value of vertical position of message that is presented in TV / Monitor ( 0 ~ 2 )

Position Horizontal Position Vertical

0x00 Center 0x00 Center

0x01

0x02

Left

Right

0x01

0x02

Left

Right

Motion On/Off : On/Off Code of Motion that is set in TV / Monitor ( 0 ~ 1 )

0x00 Motion Off 0x01 Motion On

Motion Direction : The direction which motion that is set in TV / Monitor moves ( 0 ~ 3 )

0x00 Left

0x01

0x02

0x03

Right

Up

Down

Motion Speed : The speed which motion that is set in TV / Monitor moves ( 0 ~ 2 )

Font Size : The font size of message that is set in TV / Monitor ( 0 ~ 2 )

Motion Speed Font Size

Normal

Slow

0x00

0x01

Standard

Small

0x00

0x01

Fast 0x02 Large 0x02

Foreground Color : Foreground Color of message that is set in TV / Monitor ( 0 ~ 7 )

Background Color : Background Color of message that is set in TV / Monitor ( 0 ~ 7 )

Foreground Color Background Color

0x00

0x01

0x02

0x03

0x04

0x05

0x06

0x07

Black

White

Red

Green

Blue

Yellow

Magenta

Cyan

0x00

0x01

0x02

0x03

0x04

0x05

0x06

0x07

Black

White

Red

Green

Blue

Yellow

Magenta

Cyan

Foreground Opacity : Foreground Opacity of message that is set in TV / Monitor ( 0 ~ 5)

Background Opacity : Background Opacity of message that is set in TV / Monitor ( 0 ~ 5 )

Foreground Opacity Background Opacity

0x00

0x01

0x02

Solid

Transparent

Translucent

0x00

0x01

0x02

Black

White

Red

0x03

0x04

0x05

Flashing

Flash All

Off

0x03

0x04

0x05

Green

Blue

Yellow

Message Data : Enter Ticker Message that is displayed in TV / Monitor.

It is sent as hexadecimal value of unicode and it can be entered up to 111 words.

ex) Hello => 0x48 0x65 0x6C 0x6C 0x6F

Font Style Reset : If font size reset is chosen in MDC Application, all values from Data 13 to Data 17

will be 0x00 and Set command is sent to get Default value.

●

Ack

Header Command ID Data Length Ack/Nak r-CMD Val 1 Val 2

0xAA 0xFF Length 'A' 0x63

Ticker

On/Off

Val 3

Start Minute

Val 11

Motion

Direction

Val 19

Val 4

Start

AM/PM

Val 12

Motion

Speed

Val 20

Message

Date 2

Message

Date 3

Val1 ~ ValN : Same as above

●

Nak

Header Command

...

ID

0xAA 0xFF

Val 5

End Hour End Minute End AM/PM

Val 13

Val 6

Val 14

Val 7

Val 15

Val 8

Position

Horizontal

Val 16

Font Size

Val 21

Val 9

Position

Vertical

Val 17

Foreground

Color

Background

Color

Foreground

Opacity

Background

Opacity

Val 22

...

Val N

Message

Date N

Check

Sum

Data Length Ack/Nak

0x03 'N' r-CMD

0x63

Val 1

ERR


Start Hour

Val 10

Motion

On/Off

Val 18

Message

Date 1

Check

Sum

2.1.65 Sound Select Control

●

Function

The PC changes the sound when the PIP of a TV or monitor is set to On.

Note : Same function is also exist on 0x47

●

Get the Sound Select


0xAA 0x65

ID

0x00

Check

Sum

●

Set the Sound Select


0xAA 0x65

ID

0x01 S.Selct

Check

Sum

S.Select

: The Sound Select code to set for the TV or monitor

0x00 Sub 0x01 Main

●

Ack

Header Command

ID

Data Length Ack/Nak

0x03 'A' 0xAA 0xFF

S.Select

: Same as above.

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x65 r-CMD

0x65

Val 1

S.Select

Val 1

ERR


Check

Sum

Check

Sum

2.1.66 PC Module Detect

●

Function

Check ths connection status of PC Modules

●

Get Only


ID

0xAA 0x66 0x00

●

Ack

Header Command

Check

Sum

Data Length Ack/Nak

ID

0xAA 0xFF 0x03 'A'

Detection Source : Information of detected Source

0x00 Not Detected

0x01

0x02

MagicInfo

Plug In Module

●

Nak


ID

0xAA 0xFF 0x03 'N'

ERR : Error Code showing what occurred error is. r-CMD

0x66

Val 1

Detection

Source

Check

Sum r-CMD

0x66

Val 1

ERR

Check

Sum

2.1.67 Device Name

●

Function

It reads the device name which user set up in network.

●

Get Only

Header Command

0xAA 0x67

ID

Data Length

0x00

Check

Sum

●

Ack


0xAA 0xFF

ID

Length 'A' 0x67

Device

Name

Data1

Device

Name

Data 2

Val 3 Val 4 Val 5 Val N

Device

Name

Data 3

...

...

Device

Name

Data N

Check

Sum

Length : It means the variable length of data transmitted.

It can be answered differently depending on the length of message data and the maximum length of device name is 15.

Device Name : It shows the information about entered device name.

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x03

Ack/Nak

'N' r-CMD

0x67

Val 1

ERR

Check

Sum


2.1.68 Speaker Select

●

Function

Personal Computer chooses a Speaker in TV / Monitor

●

Get Speaker Select


0xAA 0x68

ID

0x00

Check

Sum

●

Set Speaker Select

Header Command

ID

Data Length Data 1

0xAA 0x68 0x01 S.Selct

Check

Sum

S.Select

: Speaker Select Code that is going to be set in TV / Monitor

0x00 Internal 0x01 External

●

Ack


ID

0x03 'A' 0x68 0xAA 0x68

S.Select

: Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x68


Val 1

S.Select

Val 1

ERR

Check

Sum

Check

Sum

2.1.70 OSD On/Off

●

Function

Personal Computercontrol OSD on/off of TV / Monitor

Note : In case OSD on Set display ODS on it’s screen and in the case off there will be no ODS

●

Get OSD Enable Status


0xAA 0x70

ID

0x00

Check

Sum

●

Set OSD Enable/Disable


0xAA 0x70

ID

0x01 OSD

Check

Sum

OSD : OSD code to set TV / Monitor

0x00 OSD Off

●

Ack

Header Command

ID

0xAA 0xFF

0x01

Data Length Ack/Nak

0x03 'A'

OSD On r-CMD

0x70

Val 1

Check

Sum

OSD

OSD : Same as above

Note : Depends on HongKong airport protocol option, ACK/NAK will returned in opposite way

●

Nak


0xAA 0xFF

ID

0x03 'N' 0x70 ERR

Check

Sum


2.1.71 P.Mode Control

●

Function

Personal Computercontrol picture mode of the TV / Monitor

●

Get Picture Mode Status


0xAA 0x71

ID

0x00

Check

Sum

●

Set Picture Mode


ID

0xAA 0x71 0x01 PMode

PMode : Picture mode to set MFM/LFD

Source Data Mode

AV

S-Video

Component

HDCP

(TV)

PC

BNC

DVI

DisplayPort

(MagicNet)

All

0x12

0x13

0x14

0x15

0x16

0x50

0x20

0x21

0x00

0x01

0x02

0x03

0x04

0x05

0x50

0x10

0x11

0x22

0x23

0x24

0x25

Dynamic

Standard

Movie

Custom

Natural

Calibration

Off

Entertain

Internet

Text

Custom

Advertisement

Information

Calibration

Off

Shop & Mall - Video

Shop & Mall - Text

Office & School - Video

Office & School - Text

Terminal & Station - Video

Terminal & Station - Text

Check

Sum

0x26 Videowall - Video

0x27 Videowall - Text

Note :

- Dynamic contrast will work only the picture mode is off

- Depends on each model spec it will support the picture mode : 0x16 and 0x20~0x27 only

●

Ack


0xAA 0xFF

ID

0x03 'A' 0x71 PMode

Check

Sum

PMode : 상동

●

Nak


ID

0xAA 0xFF 0x03 'N'


r-CMD

0x71

Val 1

ERR

Check

Sum

2.1.72 S.Mode Control

●

Function

Personal Computer Set sound mode on TV / Monitor

●

Get Sound Mode Status


0xAA 0x72

ID

0x00

Check

Sum

●

Set Sound Mode


ID

0xAA 0x72 0x01 SMode

SMode : Sound Mode Code

0x00 Standard

0x01

0x02

0x03

0x04

Music

Movie

Speech

Custom

Amplify

Optimized

0x05

0x06

●

Ack


0xAA 0xFF

SMode : Same as above

●

Nak

Header Command

ID

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N'

Check

Sum r-CMD

0x72 r-CMD

0x72

Val 1

SMode

Val 1

ERR

Check

Sum

Check

Sum

2.1.73 Digital NR Control

●

Function

Personal Computer changes Digital NR mode.

●

Working Condition



it will not affect by the 1st condition and instead,



Note : It will work as Digital Clean View in the menu depends on each model spec

●

Get NR Mode Status


0xAA 0x73

ID

0x00

Check

Sum

●

Set NR Mode


0xAA 0x73

ID

0x01 NR Mode

Check

Sum

NR Mode : NR Mode On/Off code to set in TV / Monitor

0x00 NR Mode Off

0x01

0x02

NR Mode Low(On)

NR Mode Medium

0x03

0x04

0x05

NR Mode High

NR Mode Auto

NR Mode Auto

Visualization

●

Ack

Header Command

ID

0xAA 0xFF

NR Mode : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03

Data Length Ack/Nak

0x03

'A'

'N'

ERR : Error Code showing what occurred error is. r-CMD

0x73 r-CMD

0x73

Val 1

NR Mode

Val 1

ERR

Check

Sum

Check

Sum

2.1.75 PC Color Tone Control

●

Function

Personal Computer can change color tone of Monitor.

●

Working Condition



it will not affected by the 1st condition and instead,

It will work with **** Text of picture mode in the menu

●

Get Color Tone Status


0xAA 0x75

ID

0x00

Check

Sum

●

Set Color Tone


0xAA 0x75

ID

0x01 Color Tone

Check

Sum

Color Tone : Color Tone value code to set on TV/Monitor (0 ~ 3)

0x00 Custom

0x01

0x02

Cool

Normal

0x03

0x50

Warm

Off

●

Ack

Header Command

ID

0xAA 0xFF

Color Tone : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03


'N' r-CMD

0x75 r-CMD

0x75

Val 1

Color Tone

Val 1

ERR

Check

Sum

Check

Sum

2.1.76 Auto AutoAdjustment

●

Function

Personal Computer can Enable/Disable Auto Adjustment function.

Note : If this value is Disable. then Auto Adjustment is not work.

●

Get A.Adjustment Status


0xAA 0x76

ID

0x00

Check

Sum

●

Set A.Adjustment


0xAA 0x76

ID

0x01

A.Adjustme

nt

Check

Sum

A. Adjustment : Auto Auto Adjustment Enable/Disable Value Code to be set on TV/Monitor

0x00 Disable 0x01 Enable

●

Ack


0xAA 0xFF

ID

0x03 'A' 0x76

Val 1

A.Adjustme

nt

Check

Sum

A.Adjustment

: Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x76

Val 1

ERR

Check

Sum


2.1.77 All Keys Lock

●

Function

rsonal Computer turns both REMOCON and Panel Key Lock function on/off.

Note : Can operate regardless of whether power is on/off.

●

Get All Key Status


0xAA 0x77

ID

0x00

Check

Sum

●

Set All Key Lock/Unlock


0xAA 0x77

ID

0x01 AKL

Check

Sum

All Key : Lock On/Off code of every Key to be set on TV/Monitor

0x00 OFF 0x01 ON

●

Ack


ID

0xAA 0xFF 0x03 'A'

All Key : Same as above

●

Nak


ID

0xAA 0xFF 0x03


'N' r-CMD

0x77 r-CMD

0x77

Val 1

AKL

Val 1

ERR

Check

Sum

Check

Sum

2.1.78 SRS TSXT Control

●

Function

Personal Computer turns SRS TS XT of TV / Monitor on/off.

●

Get SRS TS XT Status


0xAA 0x78

ID

0x00

Check

Sum

●

Set SRS TSXT


ID

0xAA 0x78 0x01 SRS

Check

Sum

SRS : SRS TS XT code to be set on TV/Monitor

0x00 SRS OFF 0x01

●

Ack

Header Command

SRS ON


ID

0x03 'A' 0x78 0xAA 0xFF

SRS : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0x78


Val 1

SRS

Val 1

ERR

Check

Sum

Check

Sum

2.1.79 Film Mode Control

●

Function

Personal Computer turns Film Mode of TV / Monitor on/off.

●

Get Film Mode Status


0xAA 0x79

ID

0x00

Check

Sum

●

Set Film Mode


ID

0xAA 0x79 0x01 FMode

FMode : Film Mode code to be set on TV/Monitor

0x00 Film Mode OFF

0x01

0x02

0x03

●

Ack

Header

Film Mode Auto1

Film Mode Auto2

Film Cinema Smooth


ID

0x03 'A' 0xAA 0xFF

FMode : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


Check

Sum r-CMD

0x79 r-CMD

0x79

Val 1

FMode

Val 1

ERR

Check

Sum

Check

Sum

2.1.83 Panel On Time

●

Function

Personal Computer shows Panel On Time of TV / Monitor.

●

Get Panel On Time Status


0xAA 0x83

ID

0x00

Check

Sum

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x04 'A'

Check

Sum

PTime_H : Panel On Time data High byte.

PTime_L : Panel On Time data Low byte.

Note : Return value will increase every 10 mins.

●

Nak


ID

0xAA 0xFF 0x03 'N'


0x83

Val 1

PTime_ H

Val 2

PTime_L r-CMD

0x83

Val 1

ERR

Check

Sum

2.1.84 Video Wall On

●

Function

Personal Computer turns Video Wall of TV / Monitor ON/OFF.

●

Working Condition

- Does not operate in MagicNet source.

●

Get Video Wall On/Off Status


0xAA 0x84

ID

0x00

Check

Sum

●

Set Video Wall On/Off


ID

0xAA 0x84 0x01 V.Wall_On

V.Wall_On : Video Wall Code to set on TV / Monitor

0x00 Video Wall OFF 0x01

Check

Sum

Video Wall ON

●

Ack

Header Command

ID

0xAA 0xFF

V.Wall_On : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03 'N' r-CMD

0x84 r-CMD

0x84


Val 1

V.Wall_On

Val 1

ERR

Check

Sum

Check

Sum

2.1.85 Temperature Control

●

Function

Personal Computer sets the maximum value of TV / Monitor temperature.

●

Working Condition

- Only supports models with Temperature notification function.

●

Get Temperature Status


0xAA 0x85

ID

0x00

Check

Sum

●

Set Temperature Status


0xAA 0x85

ID

0x01

Temperatur e

Check

Sum

Temperature : Temperature code to be set on TV/Monitor(75 ~ 124 ℃)

●

Ack


ID

0xAA 0xFF 0x03 'A' 0x85

Val 1

Temperatur e

Temperature : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x85

Val 1

ERR


Check

Sum

Check

Sum

2.1.86 Brightness Sensor

●

Function

Personal Computer turns Brightness Sensor of TV / Monitor on/off.

●

Get Brightness Sensor ON/OFF Status


0xAA 0x86

ID

0x00

Check

Sum

●

Set Brightness Sensor ON/OFF

Header Command

ID

0xAA 0x86

Data Length

0x01

Data 1

BR_Sensor

Check

Sum

BR_Sensor : Brightness Sensor Code to be set on TV/Monitor

0x00 Brightness Sensor OFF 0x01 Brightness Sensor ON

●

Ack

Header Command

0xAA 0xFF

BR_Sensor : Same as above

●

Nak

ID

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03


'N' r-CMD

0x86 r-CMD

0x86

Val 1

BR_Sensor

Val 1

ERR

Check

Sum

Check

Sum

2.1.87 Dynamic Contrast

●

Function

Personal Computer changes Dynamic Contrast of TV/Monitor.

Note : It will be work or not depends on the Picture mode

●

Get Dynamic Contrast Status


0xAA 0x87

ID

0x00

Check

Sum

●

Set Dynamic Contrast


ID

0xAA 0x87 0x01 DY_Cont

Check

Sum

DY_Cont : Dynamic Contrast code to be set on TV/Monitor

0x00 Dynamic Contrast OFF

0x01

0x02

0x03

Dynamic Contrast Low(ON)

Dynamic Contrast Medium

Dynamic Contrast High

●

Ack


0xAA 0xFF

_Cont : Same as above

●

Nak

Header Command

ID

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N' r-CMD

0x87 r-CMD

0x87

Val 1

DY_Cont

Val 1

ERR

Check

Sum

Check

Sum

2.1.89 Video Wall User Control

●

Function

Personal Computer turns Video Wall function of TV / Monitor on/off.

●

Working Condition

Does not operate in MagicNet mode.

●

Get Video Wall Status


0xAA 0x89

ID

0x00

Check

Sum

●

Set Video Wall


ID

0xAA 0x89 0x02 Wall_Div

Wall_Div : Video Wall Divider code set on TV/Monitor


5x5 Video Wall

Data 2

Wall_SNo

Check

Sum

10x10 Video Wall

15x15 Video Wall

H

V

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

OFF

0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00

1

0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F

2


3


4


5


6

0x61

0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F

7

0x71


8 0x81


9


10

0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF

11

0xB1

0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF

12

0xC1

0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF

13

0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC 0xDD 0xDE 0xDF

14

0xE1

0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE 0xEF

15

0xF1

0xF2 0xF3 0xF4 0xF5 0xF6 0xF7 0xF8 0xF9 0xFA 0xFB 0xFC 0xFD 0xFE 0xFF

Wall_SNo : TV / Monitor 에 설정된 TV/Monitor 의 Number code.

- 5x5 Video Wall Model : ( 1 ~ 25 )



●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 0x04 'A'

Check

Sum

Wall_Div, Wall_SNo : Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N'


0x89

Val 1

Wall_Div

Val 2

Wall_SNo r-CMD

0x89

Val 1

ERR

Check

Sum

2.1.8A Model Name Control

●

Function

Personal Computer grasps TV / Monitor Model Name and display.

●

Get Model Number Status


0xAA 0x8A

ID

0x00

Check

Sum

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

Length 'A' r-CMD

0x8A

Val 1 Val 2

M_Name1 M_Name2

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 Val 9 Val 10

M_Name3 M_Name4 M_Name5 M_Name6 M_Name7 M_Name8 M_Name9 M_Name10

Val 11 Val 12 Val 13 Val 14 Val 15 Val 16 Val 17 Val ...

M_Name11 M_Name12 M_Name13 M_Name14 M_Name15 M_Name16 M_Name17 M_Name...

Check

Sum

M_Name1 ~ M_Name...

: TV / Monitor's Model Name.

Length : Length means number of M_Name elements & Ack/Nak & r-CMD.

Ex) SyncMaster400DXn

M_Name1 'S'

M_Name2

M_Name3

'y'

'n'

M_Name4

M_Name5

M_Name6

M_Name7

M_Name8

'c'

'M'

'a'

's'

't'

M_Name9

M_Name10

M_Name11

M_Name12

M_Name13

M_Name14

M_Name15

M_Name16

'e'

'r'

'4'

'0'

'0'

'D'

'X'

'n'

●

Nak

Header Command ID Data Length Ack/Nak r-CMD Val 1 Check

0xAA 0xFF 0x03


'N' 0x8A ERR

Sum

2.1.8B Video Wall Direct User Control

●

Function

The PC turns the Video Wall of a TV or monitor on/off.

●

Working Condition

This does not operate while PIP is operating.

●

Get the Video Wall Status

Header Command

ID

Data Length

0xAA 0x8B 0x00

Check

Sum

●

Set the Video Wall

Header Command

ID

Data Length Data 1

0xAA 0x8B 0x05

Data 2 Data 3

V.Wall_On

WallMode Wall_Div

Data 5

Input

Check

Sum

V.Wall_On

: The Video Wall code to set for the TV or monitor.

0x00 Video Wall OFF 0x01 Video Wall ON

Data 4

Wall_SNo

WallMode : The Video Wall mode code to set for the TV or monitor.

0x00 Natural 0x01 Full

Wall_Div : The Video Wall Divider code set for the TV or monitor.

- Please refer Wall_Div table of Command 0x89,


Wall_SNo : The TV/Monitor serial number code set for the TV or monitor.

- Please refer Wall_SNo table of Command 0x89,


Input : The input source code to set for the TV or monitor.

- Please refer Input table of Command 0x14,

Input Source Control (MFM)

.

●

Ack


ID

0xAA 0xFF 0x07 'A' 0x8B

Val 2

V.Wall_On

WallMode

Val 3

Wall_Div

Val 4

Wall_SNo

Val 5

Input

Check

Sum


●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0x8B

Val 1

ERR

Check

Sum


2.1.8C Video Wall Feature Control

●

Function

Control video wall related function

●

Get Video Wall Feature info

Header Command

ID

0xAA 0x8c

Sub CMD

: Function

Sub CMD Function

0x81 Frams Alignment

●

Set Video Wall Feature - Overall

Header Command

ID

0xAA 0x8c

Data Length Sub CMD

0x01 Function

Data Length xx

Sub CMD

Function

Check

Sum

Data1 xx

...

...

Check

Sum

.

Set Video Wall Feature - Sub CMD : Frame Alignment

Header Command Data Length Sub CMD

ID

0xAA 0x8c 0x02 0x81

Data1

Frame

Alignment

Mode

Frame Alignment Mode

0x00 Off

0x02 Auto

●

Ack

.

Sub CMD : Get/Set Frame Alignment

Header Command

0x01

-

Data Length

ID

0xAA 0xFF 0x04

Ack

'A'

On

- r-CMD

0x8c

Check

Sum

Sub CMD

0x81

DataN xx

Val1

Frame

Alignment

Mode

Check

Sum

●

Nak

Header Command

0xAA 0xFF

Check

Sum

ID

Data Length

0x04

Nak

'N' r-CMD r-Sub Cmd Val1

0x8c Function ERR

2.1.8F Fan Control

●

Function

The PC adjusts the Fan Control of a TV or monitor.

●

Get Fan Control Status


0xAA 0x8F

ID

0x00

Check

Sum

●

Set Fan Control


ID

0xAA 0x8F 0x01 FAN

Check

Sum

FAN : Fan Control code to be set on TV/Monitor

0x0 0 Fan Control Manual 0x0 1

●

Ack

Header Command

Fan Control Auto


ID


FAN : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'


0x8F

Val 1

FAN

Val 1

ERR

Check

Sum

Check

Sum

2.1.92 Energy Saving Control

●

Function

The PC adjusts the Energy Saving of a TV or monitor.

●

Get Energy Saving Status


0xAA 0x92

ID

0x00

Check

Sum

●

Set Energy Saving


ID

0xAA 0x92 0x01 E_SAV

Energy Saving : Energy Saving code to be set on TV/Monitor

0x00 Energy Saving Control OFF

0x01

0x02

Energy Saving Control Low(ON)

Energy Saving Control Medium

0x03

●

Ack

0x04

Header

Energy Saving Control High

Energy Saving Picture Off

Command

0xAA 0xFF

E_SAV : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

ID

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

0x03 'N'

Check

Sum r-CMD

0x92 r-CMD

0x92


Val 1

E_SAV

Val 1

ERR

Check

Sum

Check

Sum

2.1.94 HDMI Black Level Control

●

Function

Personal Computer turns HDMI Black Level function of TV / Monitor.

●

Get HDMI Black Level Status


0xAA 0x94

ID

0x00

Check

Sum

●

Set HDMI Black Level


0xAA 0x94

ID

0x01

HDMI Black

Level

Check

Sum

HDMI Black Level : HDMI Black Level Control code set on TV/Monitor

0x00 Normal

0x01

0x02

●

Ack

Header

Low

Auto

Command Data Length Ack/Nak r-CMD

ID

0xAA 0xFF 0x03 'A' 0x94

HDMI Black Level

: Same as above

●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N'


0x94

Val 1

HDMI Black

Level

Val 1

ERR

Check

Sum

Check

Sum

2.1.95 Black Adjust Control

●

Function

Personal Computer changes Black Adjust of TV / Monitor.

●

Working Condition

- Depends on each model spec it will be supported or not

●

Get Black Adjust Status


0xAA 0x95

ID

0x00

Check

Sum

●

Set Black Adjust


ID

0xAA 0x95 0x01 B_ADJ

B_ADJ : Black Adjust Control Value

0x00

Black Adjust Control OFF or Off

0x01

0x02

0x03

Black Adjust Control Low(ON) or Dark

Black Adjust Control Medium or Darker

Black Adjust Control High or Darkest

●

Ack


0xAA 0xFF

B_ADJ : Same as above

●

Nak

Header Command

ID

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N'

Check

Sum r-CMD

0x95 r-CMD

0x95

Val 1

B_ADJ

Val 1

ERR

Check

Sum

Check

Sum

2.1.96 Gamma Control

●

Function

The PC adjusts the Gamma Control of a TV or monitor.

●

Get Gamma Status


0xAA 0x96

ID

0x00

Check

Sum

●

Set Gamma


ID

0xAA 0x96 0x01 GAMMA

GAMMA : Gamma code to be set on TV/Monitor

0x00 Natural (0)

0x01

0x02

0x03

0x04

0x05

0x11

0x12

0x13

0x14

0x15

0x20

●

Ack

Header

Mode1 (1)

Mode2 (2)

Mode3 (3)

Mode4 (4)

Mode5 (5)

-1

-2

-3

-4

-5

Custom


ID

0x03 'A' 0xAA 0xFF

GAMMA : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'


Check

Sum r-CMD

0x96 r-CMD

0x96

Val 1

GAMMA

Val 1

ERR

Check

Sum

Check

Sum

2.1.9C Edge Enhancement Control

●

Function

Personal Computer changes Edge Enhancement of TV/Monitor.

●

Working Condition


●

Get Edge Enhancement Status


0xAA 0x9C

ID

0x00

Check

Sum

●

Set Edge Enhancement


0xAA 0x9C

ID

0x01 EDGE

Check

Sum

EDGE : Edge Enhancement Control value set on TV/Monitor

0x00 Edge Enhancement Control OFF 0x01

●

Ack


ID

0x03 'A' 0xAA 0xFF

EDGE : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


Edge Enhancement Control ON r-CMD

0x9C r-CMD

0x9C

Val 1

EDGE

Val 1

ERR

Check

Sum

Check

Sum

2.1.9D Color Space Control

●

Function

Personal Computer changes Color Space of TV/Monitor.

●

Working Condition




●

Get Color Space Status


0xAA 0x9D

ID

0x00

Check

Sum

●

Set Color Space


0xAA 0x9D

ID

0x01 COS

Check

Sum

COS : Color Space Control value set on TV/Monitor

0x00 Color Space Control Auto

0x01

0x02

●

Ack

Header

Color Space Control Native

Color Space Control Custom


ID

0x03 'A' 0xAA 0xFF

COS : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N' r-CMD

0x9D r-CMD

0x9D

Val 1

COS

Val 1

ERR

Check

Sum

Check

Sum


2.1.9E xvYCC Control

●

Function

Personal Computer changes xvYCC of TV/Monitor.

●

Working Condition


●

Get xvYCC Status


0xAA 0x9E

ID

0x00

Check

Sum

●

Set xvYCC


ID

0xAA 0x9E 0x01 XVYCC

XVYCC : xvYCC Control code set on TV/Monitor

0x00 xvYCC Control OFF 0x01

Check

Sum xvYCC Control ON

●

Ack

Header Command

0xAA 0xFF xvYCC : Same as above

●

Nak

Header Command

ID

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N' r-CMD

0x9E r-CMD

0x9E

Val 1

XVYCC

Val 1

ERR

Check

Sum

Check

Sum

2.1.9F Reset Control

●

Function

The PC adjusts the Reset Control of a TV or monitor.

●

Get Reset

It will always returns as NAK

●

Set Reset


ID

0xAA 0x9F 0x01 RST

RST : Reset code to be set on TV/Monitor

0x00 Picture Reset

0x01

0x02

0x03

0x04

Sound Reset

Setup Reset(System Reset)

Reset All

Screen Display Reset

●

Ack

Header Command

0xAA 0xFF

RST : Same as above

●

Nak

Header Command

ID

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N'

Check

Sum r-CMD

0x9F r-CMD

0x9F

Val 1

RST

Val 1

ERR

Check

Sum

Check

Sum

2.1.A1 Ambient Brightness Mode

●

Function

The PC adjusts Ambient Brightness Mode On/Off of a TV or monitor.

And, Setting Lamp value for Ambient Brightness On.

●

Get Ambient Brightness Mode Status


0xAA 0xA1

ID

0x00

Check

Sum

●

Set Ambient Brightness Mode, Set Lamp Value


ID

0xAA 0xA1 0x03

Data 1

AB_Mode

Data 2 Data 3

Valid_

LampValue

Lamp Value

Check

Sum

AB_Mode : Ambient Mode On/Off code to be set on TV/Monitor

0x00 Ambient Brightness Mode Off 0x01 Ambient Brightness Mode On

Valid_LampValue : Lamp Value Apply/Not apply to be set on TV/Monitor

0x00 Invalid Lamp Value(Don't apply) 0x01 Valid Lamp Value (Apply)

Lamp Value : Lamp Value to be set on TV/Monitor (0 ~ 100),

●

Ack

Header Command

ID

Data Length Ack/Nak


0xA1

Val 1 Val 2

AB_Mode Lamp Value

Check

Sum

AB_Mode, Valid_LampValue,Lamp Value : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'


0xA1

Val 1

ERR

Check

Sum

2.1.A3 OSD Display Type On/Off

●

Function

The PC adjusts the OSD Display Control of a TV or monitor.

"OSD On" means, Display OSD which is set on OSD Type.

"OSD Off" means, Does not display which is set on OSD Type.

●

Get OSD Enable Status


0xAA 0xA3

ID

0x00

Check

Sum

●

Set OSD Enable/Disable


ID

0xAA 0xA3 0x02

OSD

Type

OSD On/Off

Check

Sum

OSD Type : Select OSD Type code to be set on TV/Monitor

0x00 Source OSD 0x01 Not Optimum Mode OSD

0x02

0x04

No Signal OSD

Schedule Channel Info

0x03

-

MDC OSD

-

OSD ON/OFF: Adjust OSD On/Off code to be set on TV/Monitor

0x00 OSD Off 0x01 OSD On

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'A' r-CMD

0xA3

Val 1

BIT7 BIT6

Reserved Reserved

Val 1

BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 Check

Sum

Reserved Reserved

Type 3

On/Off

Type(OSD Type)

: Same as Above

Type 2

On/Off

Type 1

On/Off

Type 0

On/Off

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x03 'N'


0xA3

Val 1

ERR

Check

Sum

2.1.A4 Timer1 Control_MFM

●

Function:

Personal Computer controls the Timer1 that TV / Monitor.


●

Get Timer1 Status


0xAA 0xA4

ID

0x00

Check

Sum

●

Set Timer1

On Timer/Off Timer Integrated.

Header Command

ID

0xAA 0xA4

Data Length

0x0D

Data 1

On H

Data 5 Data 6 Date 7 Data 8 Data 9

Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12

Off H Off M Off AM/PM Off_Act Repeat

Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum

On Timer/Off Timer Seperated (Added two Items, Data Length is different)

Header Command

ID


0xAA 0xA4 0x0F On H On M

Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M

Date 7 Data 8 Data 9 Data 10 Data 11 Data 12

Off AM/PM Off_Act Repeat_On

Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff

Data 13 Data 14 Data 15

Volume Source

Holiday

Apply

Check

Sum

On H : On Time Hour value to be set on TV/Monitor ( 1 ~ 12 )

On M : On Time Minute value to be set on TV/Monitor ( 0 ~ 59 )

On AM/PM :On Time AM/PM value to be set on TV/Monitor (0~1)

0x00 PM 0x01 AM

On_Act : On Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))

Off H : Off Time Hour value to be set on TV/Monitor ( 1 ~ 12 )

Off M : Off Time Minute value to be set on TV/Monitor ( 0 ~ 59 )

Off AM/PM : Off Time AM/PM value to be set on TV/Monitor (0~1)

0x00 PM 0x01 AM

Off_Act : Off Time Inactivated /Activated to be set on TV/Monitor (0(off)~1(on))

Repeat_On/Repeat Off : Repeat value to be set on TV/Monitor (0~5)

0x00 Once 0x01 Everyday

0x02 Mon~Fri 0x03 Mon~Sat

0x04 Sat~Sun 0x05 Manual Weekday

ManualWeekday/ManualWeekdayOn/ManualWeekdayOff : Weekday value to be set on TV/Monitor.

BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0

Mon Sun X Sat Fri Thu

Note : Don’t care for BIT7

Volume : Volume to be set on TV/Monitor.

Wed Tue

Source : Source to be set on TV/Monitor.

Note : 0x61, WiDi is not available, 0x62 : Internal/USB, USB

Holiday Apply : Apply or not the Holiday to On/Off Timer1 ( 0 ~ 3 )

0x00 Dont't Apply(Both) 0x01 Apply(Both)

Off Timer1 only Apply 0x02 On Timer1 only Apply

●

Ack

On Timer/Off Timer Integrated

Header Command

ID

0xAA 0xFF

Val 3 Val 4 Val 5

0x03

Data Length Ack/Nak

0x0F 'A'

Val 6 Val 7

On AM/PM On_Act Off H Off M Off AM/PM r-CMD

0xA4

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday

Val 11 Val 12 Val 13

Volume Source

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xFF 0x11 'A' 0xA4

Val 1

On H

Va 3 Val 4 Val 5 Val 6 Val 7 Val 8 Val 9

On AM/PM On_Act Off H Off M Off AM/PM Off_Act Repeat_On

Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply

Val1 ~ Val15 : Same as above

Note : If H/M Time values are 0xFF, Time didn't set in LFD.

●

Nak


ID

0xAA 0xFF 0x03 'N'

Check

Sum r-CMD

0xA4

Val 1

ERR

Check

Sum



●

Function:



●

Get Timer2 Status


0xAA 0xA5

ID

0x00

Check

Sum

●

Set Timer2


Header Command

ID

0xAA 0xA5

Data Length

0x0D

Data 1

On H

Data 5

Off H

Data 6

Off M

Date 7

Off AM/PM

Data 8

Off_Act

Data 9

Repeat

Data 2

On M

Data 10

Manual

Weekday

Data 3

Data 11

Volume

Data 4

On AM/PM On_Act

Data 12

Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID



Data 3 Data 4

On AM/PM On_Act

Data 5 Data 6

Off H Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xA5

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday

Val 11

Volume

Val 12

Source

Val 13

Holiday

Apply

Check

Sum


Header Command

ID



Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'


Check

Sum r-CMD

0xA5

Val 1

ERR

Check

Sum


●

Function:



●

Get Timer3 Status


0xAA 0xA6

ID

0x00

Check

Sum

●

Set Timer3


Header Command

ID

0xAA 0xA6

Data Length

0x0D

Data 1

On H


Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12


Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID



Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xA6

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday


Volume Source

Holiday

Apply

Check

Sum


Header Command

ID



Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'

ERR

: Error code that shows what occurred error is

Check

Sum r-CMD

0xA6

Val 1

ERR

Check

Sum

2.1.A7 Clock Control_MFM

●

Function

Personal Computer controls current time of TV / Monitor


●

Working Condition

- model is developed until 2013, For after 2014 refer to 0xC5

●

Get Time Status


0xAA 0xA7

ID

0x00

Check

Sum

●

Set Time

Header Command

ID

Data Length Data 1

0xAA 0xA7 0x07 Day

Data 2

H Time


Check

Sum

Year1 Year2 AP Time

Day : Day value to be set on TV/Monitor ( 1 ~ 31 )

Month : Month value to be set on TV/Monitor ( 1 ~ 12 )

Year1 : Year value to be set on TV/Monitor (High Byte)

Year2 : Year value to be set on TV/Monitor (Low Byte) ex) Current year is 2010.

2010(Dec) → 0x07DA(Hex) => Year1: 0x07, Year2: 0xDA

Hour : Hour value to be set on TV/Monitor ( 1 ~ 12 )

Minute : Minute value to be set on TV/Monitor ( 0 ~ 59 )

AmPm : AM/PM value to be set on TV/Monitor (0 ~ 1)

0x00 PM 0x01 AM

●

Ack

Header Command

ID



Val 3

M Time

Val 4

Month

Val 5

Year1

Val 6

Year2

Val 7

AP Time

Check

Sum


Note : Hour , Minute if current time was not set on Monitor, 0xFF

●

Nak


ID

0xAA 0xFF 0x03 'N' 0xA7


Data 3

M Time

Val 1

Day

Val 1

ERR

Data 4

Month

Val 2

H Time

Check

Sum

2.1.A8 Holiday Add/Delete Control

●

Function

Personal Computer controls Holiday List of TV / Monitor.

●

Set Holiday Status


ID

0xAA 0xA8 0x05

Managemen t command

Data 2

Month1

Data 5

Check

Sum

Day2

Management Command : Adjust Command Holiday List of TV / Monitor.

0x00 Add Holiday

Data 3

Day1

Data 4

Month2

0x01

0x02

Delete Holiday

Delete All

Note :

- If param is Delete All, Data 2 ~ Data 5 must be set 0.

- Add Holiday : Add New Holiday Information "Month1/Day1 ~ Month2/Day2".

- Delete Holiday : Delete one Holiday Information "Month1/Day1 ~ Month2/Day2".

- Delete All : Delete All Holiday Information.("Data2 ~ Data5" must be 0x00.)

●

Ack


ID


Managemen t command

Val 2

Month1

Val 3 Val 4 Val 5

Check

Sum

Day1 Month2 Day2


●

Nak

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x03 'N' r-CMD

0xA8

Val 1

ERR

Check

Sum


2.1.A9 Holiday Get Control

●

Function

Personal Computer get Holiday List of TV / Monitor.


.

●

Get Total Number of Holiday

Request Total number of Holiday information of TV/Monitor.


0xAA 0xA9

ID

0x00

Check

Sum

●

Get Holiday Date


ID

0xAA 0xA9 0x01 Index

Index : Index value on Holiday List.

●

Ack

Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x07 'A'

Val 3

Day1

Val 4

Month2

Val 5

Day2

Check

Sum

Check

Sum r-CMD

0xA9

Val 1

Index

Val 2

Month1

When the value of Val 2 ~ Val 5 is 0, "Get Holiday" is an ACK, Val 1 is number of Holiday information set on TV/Monitor

When the value of Val 2 ~ Val 5 is 0xFF, requested information of index that doesn't set holiday.

Rule of Ack Command.

Input Type Index Month 1 Day 1 Month 2 Day 2

Get Number of Holiday

Total number

0 0 0 0

Index which is set

Holiday

Set Index

Month1

(Index's data)

Day1

(Index's data)

Month2

(Index's data)

Day2

(Index's data)

Index which is not set

Holiday

●

Nak

Header Command

0xAA 0xFF

Set Index

ID

0xFF 0xFF

Data Length Ack/Nak

0x03 'N'

0xFF r-CMD

0xA9

0xFF

Val 1

ERR

Check

Sum


2.1.AB Timer4 Control

●

Function:



●

Get Timer4 Status


0xAA 0xAB

ID

0x00

Check

Sum

●

Set Timer4


Header Command

ID

0xAA 0xAB

Data Length

0x0D

Data 1

On H


Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12


Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xAB 0x0F On H On M

Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xAB

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday


Volume Source

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xFF 0x11 'A' 0xAB

Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'

Check

Sum r-CMD

0xAB

Val 1

ERR

Check

Sum


2.1.AC Timer5 Control

●

Function:



●

Get Timer5 Status


0xAA 0xAC

ID

0x00

Check

Sum

●

Set Timer5


Header Command

ID

0xAA 0xAC

Data Length

0x0D

Data 1

On H


Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12


Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xAC 0x0F On H On M

Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xAC

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday


Volume Source

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xFF 0x11 'A' 0xAC

Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'

Check

Sum r-CMD

0xAC

Val 1

ERR

Check

Sum


2.1.AD Timer6 Control

●

Function:



●

Get Timer6 Status


0xAA 0xAD

ID

0x00

Check

Sum

●

Set Timer6


Header Command

ID

0xAA 0xAD

Data Length

0x0D

Data 1

On H


Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12


Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xAD 0x0F On H On M

Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xAD

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday


Volume Source

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xFF 0x11 'A' 0xAD

Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'

Check

Sum r-CMD

0xAD

Val 1

ERR

Check

Sum


2.1.AE Timer7 Control

●

Function:



●

Get Timer7 Status


0xAA 0xAE

ID

0x00

Check

Sum

●

Set Timer7


Header Command

ID

0xAA 0xAE

Data Length

0x0D

Data 1

On H


Data 2

On M

Data 10

Data 3

Data 11

Data 4

On AM/PM On_Act

Data 12


Manual

Weekday

Volume Source

Data 13

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xAE 0x0F On H On M

Data 3 Data 4

On AM/PM On_Act

Data 5

Off H

Data 6

Off M



Manual

WeekdayOn

Repeat_Off

Manual

WeekdayOff


Volume Source

Holiday

Apply

Check

Sum




0x00 PM 0x01 AM





0x00 PM 0x01 AM











Wed Tue






●

Ack


Header Command

ID

0xAA 0xFF

Data Length Ack/Nak

0x0F

0x03

'A'



0xAE

Val 8

Off_Act

Val 1

On H

Val 9

Repeat

Val 2

On M

Val 10

Manula

Weekday


Volume Source

Holiday

Apply

Check

Sum


Header Command

ID


0xAA 0xFF 0x11 'A' 0xAE

Val 1

On H



Val 2

On M

Val 10

Manual

WeekdayOn


Repeat_Off

Manual

Week dayOff

Volume Source

Holiday

Apply



●

Nak


ID

0xAA 0xFF 0x03 'N'

Check

Sum r-CMD

0xAE

Val 1

ERR

Check

Sum


2.1.AF Edit Name Control

●

Function

Personal Computer sets Edit Name for the present input of TV/Monitor.

●

Get Edit Name Status


0xAA 0xAF

ID

0x00

Check

Sum

●

Set Edit Name

Header Command

0xAA 0xAF

ID

Data Length

0x01

Data 1

EName

Check

Sum

EName : TV 가 설정할 Edit Name Code

0x00 NONE 0x10

0x01 VCR 0x11

DMA

DVD Receiver

0x02 DVD 0x12 HD STB

0x0B

0x0C

0x0D

0x0E

0x0F

●

Ack

Header

0x03

0x04

0x05

0x06

0x07

0x08

0x09

0x0A

Cable STB

Satelite STB

PVR STB

AV Receiver

Game

Camcorder

PC

DVI PC

DVI Devices

TV

IPTV

Blu-ray

HD DVD

Command

0x13

0x14

Data Length Ack/Nak

ID

0xAA 0xFF

EName : Same as Above

●

Nak

Header Command

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N'

DVD Combo

DHR r-CMD

0xAF r-CMD

0xAF

Val 1

EName

Val 1

ERR

Check

Sum

Check

Sum

2.1.B0 Virtual Remote Control

●

Function

This function support that MDC command can work same as remote control.

●

Set Virtual Remote Control

Header Command Data Length Val 1

0xAA 0xB0

ID

0x01 KeyCode

Check

Sum

KeyCode

0X01 KEY_SOURCE 0x02 KEY_POWER

0x04 KEY_1 0x05 KEY_2

0x06 KEY_3

0x08 KEY_4

0x0A KEY_6

0x0C KEY_7

0x0E KEY_9

0x10 KEY_CHANNEL_DOWN

0x12 KEY_CHANNEL_UP

0x15 KEY_YELLOW

0x1A KEY_MENU

0x23 KEY_DIGIT

0x2D KEY_EXIT

0x46 KEY_STOP

0x48 KEY_FF

0x4B KEY_TOOLS

0x5B KEY_MAGICINFO_LITE

0x61 KEY_CURSOR_DOWN

0x65 KEY_CURSOR_LEFT

0x6C KEY_RED

0x79 KEY_CONTENT

0x07 KEY_VOLUME_UP

0x09 KEY_5

0x0B KEY_VOLUME_DOWN

0x0D KEY_8

0x0F KEY_MUTE

0x11 KEY_0

0x14 KEY_GREEN

0x16 KEY_CYAN

0x1F

KEY_DISPLAY

(or KEY_INFO)

0x24

KEY_PIP_TV_VIDEO

(or KEY_BLANK)

0x45 KEY_REW

0x47 KEY_PLAY

0x4A KEY_PAUSE

0x58 KEY_RETURN

0x60 KEY_CURSOR_UP

0x62 KEY_CURSOR_RIGHT

0x68 KEY_ENTER

0x77 KEY_LOCK

0x98 DISCRET_POWER_OFF

0x9F KEY_3D

Note : In a certain model, 0x79 content key works as Home and 0x1f Display key works as Info

●

Ack

Header Command

0xAA 0xFF

KeyCode : Same as above

●

Nak

Header Command

ID

Data Length Ack/Nak

0x03 'A'

Data Length Ack/Nak

ID

0xAA 0xFF 0x03


'N' r-CMD

0xB0

Val 1

KeyCode r-CMD

0xB0

Val 1

ERR

Check

Sum

Check

Sum

2.1.B1 Display Port Daisy Chain

●

Function

Value of Display Port Daisy Chain sets Clone or Expand.

●

Get Display Port Daisy Chain Clone/Expand


ID

0xAA 0xB1 0x00

Check

Sum

●

Set Display Port Daisy Chain Clone/Expand


ID

0xAA 0xB1 0x01

Data 1

Value

Check

Sum

Value : The Value of set for Display Port Daisy Chain.

0x00 Clone 0x01

●

Ack

Header Command

Expand


ID

0xAA 0xFF 0x03 'A' 0xB1

Value : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N'

ERR : Error Code which is displayed when error is occured.

r-CMD

0xB1

Val 1

Value

Val 1

ERR

Check

Sum

Check

Sum

2.1.B3 Video Conference Sound Mode Control

●

Function

Personal Computer set Video Conference sound mode of TV/Monitor.

●

Working Condition

In case of PIP is on and the C.Sound is on PIP sound select will not work

When S.Sound mode set off, PIP sound will change as it’s last memory value

C.Sound will support last memory

●

Get Conference Sound Mode Status


0xAA 0xB3

ID

0x00

Check

Sum

●

Set Conference Sound Mode Status

Header Command

ID

0xAA 0xB3

Data Length

0x01

Data 1

C.Sound

On/Off

Check

Sum

C.Sound On/Off : Video Conference Sound On/Off set Value.

0x00 Video Conference Sound Off 0x01

●

Ack


Video Conference Sound On r-CMD Val 1

0xAA 0xFF

ID

0x03 'A' 0xB3

C.Sound

On/Off

Status

Check

Sum

C.Sound On/Off Status : Video Conference Sound On/Off set Value.

●

Nak


ID

0xAA 0xFF 0x03 'N' 0xB3

Val 1

ERR

Check

Sum


2.1.B5 Network Standby Control

●

Function

In Network supported Model, Control Network Standby function.

●

Get Network Standby Status


0xAA 0xB5

ID

0x00

Check

Sum

●

Set Network Standby Status


0xAA 0xB5

ID

0x01

Network

Standby

On/Off

Check

Sum

Network Standby On/Off : Network Standby Value

0x00 Network Standby Off 0x01 Network Standby On

●

Ack


ID



●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'

ERR : Error Code which is displayed when error is occured. r-CMD

0xB5

Val 1

Network

Standby

On/Off

Val 1

ERR

Check

Sum

Check

Sum

2.1.B6 DST (Daylight Saving Time) Control

●

Function

Control function of DST ( Daylight Saving Time )

●

Get DST Value


ID

0xAA 0xB6 0x00

●

Set DST Value


0xAA

Data 5

0xB6

Data 6

Time H of

Start date

Time M of

Start date

Check

Sum

ID

0x0C

Data 1

DST On/Off

Data 2

Month of

Start Date

Data 3

Value1 of

Day on

Start Date

Data 11 Data 7

Month of

End Date

Data 8 Data 9

Value1 of

Day on End

Date

Value2 of

Day on End

Date

Data 10

Time H of

End date

Time M of

End date

Check

Sum

DST On/Off : DST Value

Tunerless Model

0x00

0x01

DST Off

--

Tuner supported Model

0x00 DST Off

0x01 Auto

0x02 DST On 0x02 Manual

Note : Data2 ~12 are valid in case of DST On or Manual

Month of Start Date : Month in which DST starts(0x00 : Jan ~ 0x0b : Dec)

Month of End Date : Month in which DST ends (0x00 : Jan ~ 0x0b : Dec)

Value1 of Day on Start Date : Order of the day of the week in which DST start.

Value1 of Day on End Date : Order of the day of the week in which DST ends.

0x00 1st

0x01

0x02

0x03

2nd

3rd

4th

0x04 Last

Value2 of Day on Start Date : Day of week in which DST starts(0x00 : Sun ~ 0x06 : Sat)

Value2 of Day on End Date : Day of week in which DST ends(0x00 : Sun ~ 0x06 : Sat)

Time H of Start date : Hours of the time that DST starts ( 0 ~ 23 )

Time M of Start date : Minutes of the time that DST starts ( 0 ~ 59 )

Time H of End date : Hours of the time that DST ends ( 0 ~ 23 )

Time M of End date : Minutes of the time that DST ends ( 0 ~ 59 )

Time Off Set : Value of Time offset

Data 4

Value2 of

Day on

Start Date

Date 12

Time Off

Set

0x00

●

Ack

Header

+1:00 0x01 +2:00

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x0F 'A' r-CMD

0xB6

Val 1 Val 2

DST On/Off

Val 9

Month of

Start Date

Val 10 Val 3 Val 4 Val 5 Val 6 Val 7 Val 8

Value1 of

Day on

Start Date

Value2 of

Day on

Start Date

Time H of

Start date

Time M of

Start date

Month of

End Date


Time M of

End date

Time Off

Set

Tuner/Tuner less Model

Check

Sum

Tuner/Tunerless Model : Tuner - 1, Tunerless - 0

●

Nak


ID

0xAA 0xFF 0x03 'N'


Value1 of

Day on End

Date

Value2 of

Day on End

Date r-CMD

0xB6

Val 1

ERR

Time H of

End date

Check

Sum

2.1.B7 Custom PIP Control

●

Function

When PIP Size is set to "Custom", control the value of custom PIP.

●

Get Custom PIP status


0xAA 0xB7

ID

0x00

Check

Sum

●

Set Custom PIP


ID

0xAA 0xB7 0x08

H Position

High-Byte

H Position

Low-Byte

Data 3

V Position

High-Byte

Data 4

V Position

Low-Byte

Data 5 Data 6 Data 7 Data 8

H Size

High-Byte

H Size

Low-Byte

V Size

High-Byte

V Size

Low-Byte

Check

Sum

H Position High-Byte : The Position value code for PIP H-Start High-Byte.

H Position Low-Byte : The Position value code for PIP H-Start Low-Byte.

V Position High-Byte : The Position value code for PIP V-Start High-Byte.

V Position Low-Byte : The Position value code for PIP V-Start Low-Byte.

H Size High-Byte : The Size value code for PIP H-width High-Byte.

H Size Low-Byte : The Size value code for PIP H-width Low-Byte.

V Size High-Byte : The Size value code for PIP V-width High-Byte.

V Size Low-Byte : The Size value code for PIP V-width Low-Byte.

Note :

- The PIP Start Position and Size can not over panel H, V size

- H/V Size : 512 * 288 ~ 1632 * 918 (H Interval : 160 pixel, V Interval : 90 pixel)

●

Ack

512*288, 672*378, 832*468, 992*558, 1152*648, 1312*738, 1472*828, 1632*918

- H/V Position : Interval 10 Pixel


ID

0xAA 0xFF 0x0A 'A' 0xB7

H Position

High-Byte

H Position

Low-Byte


V Position

Low-Byte

H Size

High-Byte

H Size

Low-Byte

V Size

High-Byte

V Size

Low-Byte

Check

Sum

V Position

High-Byte

●

Nak


0xAA 0xFF

ID

3 'N' 0xB7 ERR

Check

Sum


2.1.B8 Auto ID Setting Status Control

●

Function

Control Start/End of Auto ID Setting.

●

Get Auto ID Setting Status


ID

0xAA 0xB8 0x00

●

Set Auto ID Setting Status


ID

0xAA 0xB8 0x01

Check

Sum

Data 1

Status

Check

Sum

Status : value of Auto ID settings status.

0x00 Auto ID Setting START 0x01

●

Ack

Header Command

Auto ID Setting END


ID



●

Nak


ID

0xAA 0xFF 0x03 'N'


r-CMD

0xB8

Val 1

Status

Val 1

ERR

Check

Sum

Check

Sum

2.1.B9 Display ID Information

●

Function

Displaying function ID of Monitor.

●

Set Monitor ID

Header Command

ID

0xAA 0xB9

Data Length

0x01

Data 1

ID Display

On/Off

Check

Sum

ID Display On/Off : Monitor ID

0x00 Monitor ID Display Off

●

Ack

Header Command

ID

0xAA 0xFF

0x01

Data Length Ack/Nak

0x03

Monitor ID Display On

'A'


●

Nak

Header Command

0xAA 0xFF

ID

Data Length Ack/Nak

0x03 'N'


0xB9 r-CMD

0xB9

Val 1

ID Display

On/Off

Val 1

ERR

Check

Sum

Check

Sum

2.1.C5 Clock Control_MFM (Second field can be set)

●

Function

Personal Computer controls clock of TV / Monitor

●

Working Condition

It will work on the signage device which is product after 13year

●

Get Time Status


0xAA 0xC5

ID

0x00

Check

Sum

●

Set Time

Header Command

ID

Data Length Val 1 Val 2

0xAA 0xC5 0x08 Day H Time

Val 5

Month

Val 6

Year1

Val 7

Year2

Val 8

AP Time

Check

Sum

Day : Day value to be set on TV/Monitor ( 1 ~ 31 )

Month : Month value to be set on TV/Monitor ( 1 ~ 12 )

Year1 : Year value to be set on TV/Monitor (High Byte)

Year2 : Year value to be set on TV/Monitor (Low Byte) ex) Current year is 2010.

2010(Dec) → 0x07DA(Hex) => Year1: 0x07, Year2: 0xDA

H Time : Hour value to be set on TV/Monitor ( 1 ~ 12 )

M Time : Minute value to be set on TV/Monitor ( 0 ~ 59 )

S Time : Second value to be set on TV/Monitor ( 0 ~ 59 )

AP Time : AM/PM value to be set on TV/Monitor ( 0 ~ 1 )

0x00 PM 0x01 AM

●

Ack

Header Command

ID


0xAA 0xFF 0x0A 'A' 0xC5


M Time S Time Month Year1 Year2 AP Time

Hour, Minute : Same as above

Note : Hour , Minute if current time was not set on Monitor, 0xFF

●

Nak


ID

0xAA 0xFF 0x03 'N' 0xC5


Val 3

M Time

Val 1

Day

Check

Sum

Val 1

ERR

Val 4

S Time

Val 2

H Time

Check

Sum

2.1.C6 EcoSolution control in MDC Protocol

●

Function

Control Eco Solution by MDC Protocol.

●

Get Eco Solution info

Header Command

ID

Data Length Sub CMD

0xAA 0xc6 0x01 Function

Sub CMD

: Function

No Sub CMD Function

1 0x81

●

Set Eco Solution – Overall

Header Command

0xAA 0xc6

Auto Power Off

ID

Data Length xx

Sub CMD

Function

Check

Sum

Check

Sum

AutoPowerOff Mode : Same as above

●

Nak

Header Command

ID

Data Length

0xAA 0xFF 0x03


Nak

'N'

Data1 xx r-CMD

0xc6

...

...

Val1

ERR

DataN xx

Check

Sum

.

Set Eco Solution - Sub CMD : Auto Power Off

Header Command

0xAA 0xc6

ID

Data Length Sub CMD

0x02 Function

Data1

AutoPower

Off Mode

Check Sum

AutoPowerOff Mode

0x00

0x01

0x02

Off

4 Hour(On)

6 Hour

●

Ack

0x03 8 Hour

Note : If the model has On/Off value only, Data 0 is Off and Data 1 is On. ,

. Sub CMD : Get/Set Auto Power Off

Header Command

ID

0xAA 0xFF

Data Length

0x04

Ack

'A' r-CMD

0xc6

Sub CMD

0x81

Val1

AutoPower

Off Mode

Check

Sum

2.1.C7 Control Launcher by MDC Protocol

●

Function

Control Launcher by MDC Protocol.

●

Working Condition


●

Get Launcher Info


ID

0xAA 0xc7

Sub CMD

: Function

Sub CMD Function

0x01 Function

0x81 Play Via Mode

0x82 URL Address

●

Set Launcher - Overall

Header Command

ID

Data Length Sub CMD

0xAA 0xc7 xx Function

Check

Sum

Data1 xx

...

...

DataN xx

Check

Sum

. Set Launcher - Sub CMD : Set Play Via Mode

Header Command

ID

Data Length Sub CMD

0xAA 0xc7 0x02

Data1

0x81 Play Via Mode

Check

Sum

Play Via Mode

0x00 MagicInfo

0x01 URL Launcher

0x02 MagicIWB

Note : When the Magicinfo S or MagicIWB or URL Launcher is running,

"Set Play via command" will return NAK.

. Set Launcher - Sub CMD : Set URL

Header Command Data Length Sub CMD Data1

ID

0xAA 0xc7 Variable 0x82

...

URL Address

DataN

Check

Sum

URL Address

:

ASCII code data, support 200 characters.

●

Ack

. Sub CMD : Get/Set Play Via

Header Command

ID

0xAA 0xFF

Data Length

0x04

Ack

'A'

Check

Sum

. Sub CMD : Get/Set URL

Header Command

0xAA 0xFF

ID

Data Length

Variable

Val2 ...

URL Address

●

Nak

Header Command

0xAA 0xFF

ID

ValN

Check

Sum

Data Length

0x03


Nak

'N'

Ack

'A' r-CMD

0xc7 r-CMD

0xc7 r-CMD

0xc7

Sub CMD

0x81 Play Via Mode

Sub CMD

0x82

Val1

ERR

Val1

Val1

URL

Address

Check

Sum

2.1.C8 OnScreen Display Menu Control

●

Function

Control the features of OnScreen Display Menu.

●

Working Condition


●

Get OnScreen Display info

Header Command

ID

Data Length Sub CMD

0xAA 0xc8 0x01 Function

Sub CMD

: Function

Sub CMD Function Sub CMD

0x82

0x84

0x81 Menu Orientation

0x83 Aspect Ratio

●

Set OnScreen Display – Overall

Header Command

ID

0xAA 0xc8

Data Length xx

Sub CMD

Function

Check

Sum

Function

Source Content Orientation

PIP Rotation

Data1 xx

...

...

DataN xx

Check

Sum

. Set OnScreen Display - Sub CMD : Menu Orientation

Header Command

0xAA 0xc8

ID

Data Length

0x02

Sub CMD

0x81

Data1

Menu

Orientation

Mode

Check

Sum

Menu Orientation Mode

0x00 Landscape(0) 0x01 Portrait(270)

0x02 180 0x03 90

.

Set OnScreen Display - Sub CMD : Source Content Orientation

Header Command Data Length Sub CMD Data1

0xAA 0xc8

ID

0x02 0x82

Source

Orientation

Mode

Check

Sum

Source Orientation Mode

0x00 Landscape(0) 0x01 Portrait(270)

90 0x02 180 0x03

.

Set OnScreen Display - Sub CMD : Aspect Ratio


ID

0xAA 0xc8 0x02

Sub CMD

0x83

Data1

Aspect

Ratio Mode

Check

Sum

Aspect Ratio Mode

0 Full Screen 1 Original

.

Set OnScreen Display - Sub CMD : PIP Rotation

Header Command

0xAA 0xc8

ID

Data Length Sub CMD

0x02 0x84

Data1

PIP Rotation

Mode

Check

Sum

PIP Rotation Mode

0x00 Landscape(0)

0x02 180

0x01

0x03

Portrait(270)

90

Note : PIP rotation will work properly when PIP is set as off.

If anyone wants to make a PIP rotation with PIP on status, below sequence is need

1. PIP Off 2. PIP Rotation set 3. PIP on

●

Ack

. Sub CMD : Get/Set Menu Orientation

Header Command Data Length Ack r-CMD Sub CMD Val1

0xAA 0xFF

ID

0x04 'A' 0xc8 0x81

Menu

Orientation

Mode

Check

Sum

. Sub CMD : Get/Set Source Content Orientation


ID

0xAA 0xFF 0x04

Ack

'A' r-CMD

0xc8

Sub CMD

0x82

Val1

Source

Orientation

Mode

Check

Sum

. Sub CMD : Get/Set Aspect Ratio

Header Command

ID

0xAA 0xFF

Data Length

0x04

Ack

'A' r-CMD

0xc8

Sub CMD

0x83

Val1

Aspect

Ratio Mod e

Check

Sum

. Sub CMD : Get/Set NetPIP Rotation

Header Command

0xAA 0xFF

ID

Data Length

0x04

Check

Sum

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x03

ERR

: Error code that shows what occurred error is

Nak

'N'

Ack

'A' r-CMD

0xc8 r-CMD

0xc8

Val1

ERR

Sub CMD

0x84

Val1

PIP

Rotation

Mode

Check

Sum

2.1.CA System Menu Control

●

Function

Control the features of System Menu.

●

Working Condition

Depends on each model spec it will be supported or not

●

Sub Command Table

Sub CMD Function Sub CMD

0x81

0x91

0xa1

Auto Source Switch On/Off

Power Button

No Signal Power Off

0x82

0x92

-

Function

Auto Source Switch Control

Touch control Admin Lock

-

2.1.CA.81 Auto Source Switch On/Off

●

Function

Control the Auto Source Switch On/Off setting of the device

●

Get Auto Source Switch On/Off

Header Command

ID

0xAA 0xCA

Data Length

0x01

Sub CMD

0x81

●

Set Auto Source Switch On/Off


0xAA 0xCA

ID

0x02 0x81

Check

Sum

Data1

Auto Source

Switch

OnOff

Auto Source Switch On/Off

0x00 Off

●

Ack

Header Command

0x01

Data Length Ack

On r-CMD

Check

Sum

Sub CMD

ID

0xAA 0xFF 0x04 ‘A’ 0xCA 0x81

Val1

Auto

Source

Switch

OnOff

Check

Sum

Auto Source Switch On/Off : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x04

Check

Sum


No Signal Power Off : Same as above

Nak

‘N’ r-CMD

0xCA r-Sub Cmd

0x81

Val1

ERR

2.1.CA.82 Auto Source Switch Control

●

Function

Control the Auto Source Switch setting of the device

●

Get Auto Source switch On/Off

Header Command

ID

0xAA 0xCA

Data Length

0x01

Sub CMD

0x82

●

Set Auto Source switch On/Off


ID

0xAA 0xCA 0x04 0x82

Check

Sum

Data 1

Primary

Source

Recovery

Data 2

Primary

Source

Data 3

Secondary

Source

Check

Sum

Primary Source recovery

0x00 Off 0x01 On

Primary Source : Source code to set as primary.

Code value is same with the code of 0x14 Input Source Control command

* Note : When try to set as “All” for primary source, it needs to set as 0x00.

Secondary Source : Source code to set as secondary.

Code value is same with the code of 0x14 Input Source Control command

●

Ack

Header Command Data Length Ack r-CMD Sub CMD Val1

0xAA 0xFF

ID

0x06 ‘A’ 0xCA 0x82

Primary

Source

Recovery

Val 3

Primary

Source

Val 4

Secondary

Source

Check

Sum

Primary Source recovery, Primary Source, Secondary Source : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x04

Nak

‘N’ r-CMD

0xCA r-Sub Cmd

0x82

Val1

ERR

Check

Sum


2.1.CA.91 Power Button

●

Function

Control the Power Button setting of the device

●

Get Power Button

Header Command

ID

Data Length Sub CMD

0xAA 0xCA 0x01 0x91

●

Set Power Button


ID

0xAA 0xCA 0x02 0x91

Power Button

0x00

●

Ack

Header

Power On Only

Command

ID

0xAA 0xFF

0x01

Data Length

0x04

Check

Sum

Data 1

Power

Button

Power On/Off

Ack

‘A’ r-CMD

0xCA

Check

Sum

Sub CMD

0x91

Val1

Power

Button

Check

Sum

Power Button : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x04

Check

Sum


Nak

‘N’ r-CMD

0xCA r-Sub Cmd

0x91

Val1

ERR

2.1.CA.92 Touch control Admin Lock

●

Function

Control the Power Button setting of the device

●

Get Touch control Admin Lock

Header Command

ID

0xAA 0xCA

Data Length

0x01

Sub CMD

0x92

●

Set Touch control Admin Lock

Header Command

ID

0xAA 0xCA

Data Length

0x02

Sub CMD

0x92

Admin Lock

0x00

●

Ack

Header Command

Off 0x01

Data Length Ack

On

ID

Check

Sum

Data 1

Admin

Lock r-CMD

0xAA 0xFF 0x04 ‘A’ 0xCA

Check

Sum

Sub CMD

0x92

Val1

Admin

Lock

Check

Sum

Admin Lock : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x04

Check

Sum


Nak

‘N’ r-CMD

0xCA r-Sub Cmd

0x92

Val1

ERR

2.1.CA.A1 No Signal Power Off

●

Function

Control the No signal Powr Off setting of the device

●

Get No Signal Power Off

Header Command

ID

Data Length Sub CMD

0xAA 0xCA 0x01 0xA1

●

Set No Signal Power Off


ID

0xAA 0xCA 0x02 0xA1

Check

Sum

Data 1

No Signal

Power Off

No Signal Power Off

0x00

0x02

Off

30 min

●

Ack

Header Command

ID

0xAA 0xFF

0x01

0x03

Data Length

0x04

Ack

‘A’

15 min

60 min r-CMD

0xCA

Check

Sum

Sub CMD

0xA1

Val1

No Signal

Power Off

Check

Sum

No Signal Power Off : Same as above

●

Nak

Header Command

0xAA 0xFF

ID

Data Length

0x04

Check

Sum


Nak

‘N’ r-CMD

0xCA r-Sub Cmd

0xA1

Val1

ERR

2.1.E0 Net PIP (MagicInfo Only)

●

Function

The Computer turns the PIP function ON/OFF at MagicInfo.

※ 1. The possible PIP composition and PIP size depends on H/W spec.

2. After Net PIP turns on, if user changes other sources and come back to Magicinfo,

Net PIP also should be shown.

●

Get MagicInfo PIP status

Not Support

●

Set MagicInfo PIP On –

Header Command Data Length PIP ON Data 1 Data 2

ID

0xAA 0xE0 0x14 0x01

H Position

High-Byte

H Position

Low-Byte


V Position

Low-Byte

Data 12

Country

Data 5

H Size

High-Byte

Data 13

ATV/

DTV

Data 6

H Size

Low-Byte

Data 14

AirCable

Data 7

V Size

High-Byte

Data 15

CH_NUM

High_Byte

Data 8

V Size

Low-Byte

Data 16

CH_NUM

Low_Byte

Data 3

V Position

High-Byte

Data 11

P.Source

TV Channel S.Select

Data 17

Sel_Minor

Data 18

Minor_CH

High_Byte

Data 19

Minor_CH

Low_Byte

Check

Sum

H Position High-Byte : The Position value code for PIP H-Start High-Byte.

H Position Low-Byte : The Position value code for PIP H-Start Low-Byte.

V Position High-Byte : The Position value code for PIP V-Start High-Byte.

V Position Low-Byte : The Position value code for PIP V-Start Low-Byte.

H Size High-Byte : The Size value code for PIP H-width High-Byte.

H Size Low-Byte : The Size value code for PIP H-width Low-Byte.

V Size High-Byte : The Size value code for PIP V-width High-Byte.

V Size Low-Byte : The Size value code for PIP V-width Low-Byte.

Note : The PIP Start Position and Size do not over panel H, V size

P.Source : The input source code to set for the TV or monitor.

- Please refer Input table of Command 0x14,

Input Source Control (MFM)

.

TV Channel : Channel Number ( 0 ~ 99 )

Note : 460Txn Only (Platform LFD don't use this byte)

S.Select : The Sound select Code

0x00 MagicInfo Sound 0x01 PIP Sound

Country : The value code for the country of the TV / Monitor(0 : Korea, 1 : U.S.A, ...)

ATV_DTV : The value code for the ATV/DTV of the TV / Monitor(0 : Analog TV, 1 : Digital TV)

AirCable : The value code for the Air/Cable of the TV / Monitor(0 : Air, 1 : Cable)

CH_NUM High_Byte : The value code for the Major Channel High-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)

CH_NUM Low_Byte : The value code for the Major Channel Low-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)

Sel_Minor : The value code for the Minor Channel Enable/Disable of the TV / Monitor

(0 : Enable, 1 : Disable)(DTV Only)

Minor_CH High_Byte : The value code for the Minor Channel High-Byte of the TV /

Monitor( 0 ~ 999 )(DTV Only)

Minor_CH Low_Byte : The value code for the Minor Channel Low-Byte of the TV /

Monitor( 0 ~ 999 )(DTV Only)

Note :

CH_NUM High_Byte = 0xFF, CH_NUM Low_Byte = 0xFF, Sel_Minor =

0x01, Minor_CH High_Byte = 0xFF, Minor_CH Low_Byte = 0xFF

=> Net PIP tune as last Memory channel of TV source

●

Set MagicInfo PIP Off

Header Command Data Length PIP Off

0xAA 0xE0

ID

0x01 0x00

Check

Sum

●

Ack

Header

0xAA

Command

0xFF

Val 2

H Position

High-Byte

Val 10

Val 3

V Position

Low-Byte

Val 11

Val 4

V Position

High-Byte

Val 12

TV Channel S.Select

ID

Country

Data Length Ack/Nak

0x16

Val 5

H Size

Low-Byte

Val 13

Val 6

H Size

High-Byte

Val 14

ATV_DTV

'A'

AirCable r-CMD

0xE0

PIP ON

0x01

Val 7

V Size

Low-Byte

Val 15

CH_NUM

High_Byte

Val 8

V Size

High-Byte

Val 16

CH_NUM

Low_Byte

Val 1

H Position

Low-Byte

Val 9

P.Source

Val 17

Sel_Minor

Val 18

Minor_CH

High_Byte


●

Nak

Header Command

0xAA

Val 19

Minor_CH

Low_Byte

0xFF

Check

Sum

ID

Data Length Ack/Nak

3 'N'


0xE0

Val 1

ERR

Check

Sum

2.1.E4 Apply To Status Control On Video Wall

●

Function

Control source for displaying on video wall.

●

Get Apply to status


ID

0xAA 0xE4 0x00

Check

Sum

●

Set Apply to Status

Header Command

ID

Data Length Data 1

Check

Sum

0xAA 0xE4 0x01 Status

Status : value of Apply to settings status.

0x00 Current Source 0x01

●

Ack

Header Command

MagicInfo Player S


ID

0xAA 0xFF 0x03 'A' 0xE4

Status : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0xE4


Val 1

Status

Val 1

ERR

Check

Sum

Check

Sum

2.1.F9 Panel On/Off

●

Function

Personal Computer turns Panel of TV / Monitor on/off.

●

Get Panel ON/OFF Status


0xAA 0xF9

ID

0x00

Check

Sum

●

Set Panel ON/OFF


ID

0xAA 0xF9 0x01 PN_State

Check

Sum

PN_State : Panel ON/OFF code to be set on TV/Monitor

0x01 PANEL OFF 0x00 PANEL ON

●

Ack


ID

0xAA 0xFF 0x03 'A' 0xF9

PN_State : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' 0xF9


Val 1

PN_State

Val 1

ERR

Check

Sum

Check

Sum

2.1.FD Auto ID Setting MDC Control Command

●

Function

●

Get Auto ID

Header Command

ID

Data Length

Check

Sum

0xAA 0xFD 0x00

●

Set Auto ID


ID

0xAA 0xFD 0x02 RS_Status

Note : If M_ID is 0, can't chage ID. (previous value.)

RS_Status : RS232 Output , ID information

Data 2

M_ID

Check

Sum

Bit7

0

Bit6

0

Bit5

0

Bit4

1 or 0

Bit3

0

Bit2

0

Bit1

0

1 : Initialize Monitor ID

1 : RS232 Loop Out Disable

(Initiailize Monitor ID to 0)

0 : RS232 Loop Out Enable

0 : -

Note : In Get Auto ID,can't know Monitor ID's reset status.

M_ID : ID

Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1

Change ID(1~225)

Note : If Monitor ID reset bit of RS_Status is set, ignore M_ID

●

Ack


ID


0xFD

Val 1

RS_Status

Check

Sum

RS_Status : Same as above

M_ID

: Same as above

Note : Get cmd - In Ack, M_ID is current ID which is set.

●

Nak


ID

0xAA 0xFF 0x03 'N'


ex) 1. All ID Reset : aa fd fe 02 10 00

2. All Loopout disable : aa fd fe 02 01 00

3. Set ID #1 : aa fd 00 02 01 01

4. Enable ID #1 : aa fd 01 02 00 01 r-CMD

0xFD

Val 1

ERR

Bit0

1 or 0

Bit0

Val 2

M_ID

Check

Sum

2.1.FF ACK/NAK

●

Function

Acknowledge or Negative acknowledge packet for other command

Note : Daetail format is defined on ezch command

Annex A. Reference TV MDC Command

●

Function

Describe function about This RTV Command

●

Set Status

Header Command Data Length Sub Cmd

ID

0xAA 0xC0(RTV) 2 0x00

●

Get Status

Header

●

Ack

0xAA

Header

Command

0xC0(RTV)

Command

ID

Data Length

1

Sub Cmd

0x00

Data Length Ack/Nak

ID

0xAA 0xFF 4 'A'

Data1

Sub Cmd

Data 1

Check

Sum

Check

Sum r-CMD r-SUBCMD

0xC0 0x00

Val 1

Sub Cmd

Val 1

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum

ERR : The error code indicating which error occurred. r-CMD r-SUBCMD

0x0C 0x00

Val 1

ERR

balanceA.C0.01 3D Mode Control

●

Function

The PC displays the 3D Mode settings of a TV or monitor.

●

Set the 3D Mode Status

Header Command Data Length Sub Cmd Data1

ID

0xAA 0xC0(RTV) 2 0x01 3D Mode

3D Mode: 3D Mode value code ( 0 ~ 7 ) to be set on TV / Monitor

0x00 3D

0x01 2D->3D

0x02

0x03

0x04

SBS

TNB

LBL

0x05

0x06

VS

CheckerBD

0x07 Frame Seq.

●

Get the 3D Mode Status

Header Command

ID

●

Ack

0xAA 0xC0(RTV)

Header Command

ID

0xAA 0xFF

Data Length

1

Sub Cmd

0x01

Data Length Ack/Nak

4 'A'

Check

Sum

Check

Sum r-CMD r-SUBCMD

0xC0 0x01

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x01

Val 1

3D Mode

Val 1

ERR

A.C0.02 3D Effect Control

●

Function

The PC Sets the 3D Effect settings of a TV or monitor.

●

Set the

3D Effect

Status


ID

0xAA 0xC0(RTV) 2 0x02 3D Effect

3D Effect 3D Effect value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00 Auto 0x01 Manual

●

Get the

3D Effect

Status

Header Command

0xC0(RTV)

ID

Data Length

1

Sub Cmd

0x02

Check

Sum

0xAA

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'A' r-CMD r-SUBCMD

0xC0

Check

Sum

0x02

Val 1

3D Effect

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x02

Val 1

ERR

A.C0.03 3D Perspective Control

●

Function

The PC Sets the 3D Perspective settings of a TV or monitor.

●

Set the 3D Perspective Status


0xAA 0xC0

ID

2 0x03

3D

Perspective

Check

Sum

3D Perspective: 3D Perspective value code ( 0 ~ 10 ) to be set on TV / Monitor

●

Get the 3D Perspective Status


0xC0

ID

1 0x03

Check

Sum

0xAA

●

Ack

Header Command Data Length Ack/Nak r-CMD r-SUBCMD

ID

0xAA 0xFF 4 'A' 0xC0 0x03

Val 1

3D

Perspective

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x03

Val 1

ERR

A.C0.04 3D Effect Depth Control

●

Function

The PC Sets the 3D Perspective settings of a TV or monitor.

●

Set the 3D Effect Depth Status


0xAA 0xC0(RTV)

ID

2 0x04

3D Effect

Depth

Check

Sum

3D Effect Depth: 3D Effect Depth value code ( 1 ~ 10 ) to be set on TV / Monitor

●

Get the 3D Effect Depth Status


0xC0

ID

1 0x04

Check

Sum

0xAA

●

Ack


ID


Val 1

3D Effect

Depth

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x04

Val 1

ERR

A.C0.05 3D L/R Change Control

●

Function

The PC Sets the 3D L/R Change settings of a TV or monitor.

●

Set the 3D L/R Change Status


0xAA 0xC0(RTV)

ID

2 0x05

3D L/R

Change

Check

Sum

3D L/R Chnage: 3D L/R Change value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00

Header

0xAA

●

Ack

L/R Image

●

Get the 3D L/R Change Status

Command

0xC0

ID

0x01

Data Length

1

R/L Image

Sub Cmd

0x05

Check

Sum


ID


Val 1

3D L/R

Change

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x05

Val 1

ERR

A.C0.06 3D->2D Control

●

Function

The PC Sets the 3D->2D settings of a TV or monitor.

●

Set the 3D->2D Status


ID

0xAA 0xC0 2 0x06

Data1

3D->2D

3D->2D: 3D->2D value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00 Off 0x01 On

●

Get the 3D->2D Status

Header Command

0xC0

ID

Data Length

1

Sub Cmd

0x06

Check

Sum

0xAA

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak


0xC0

Check

Sum

0x06

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x06

Val 1

3D->2D

Val 1

ERR

A.C0.07 3D Auto View Control

●

Function

The PC Sets the 3D Auto View settings of a TV or monitor.

●

Set the 3D Auto View Status


0xAA 0xC0

ID

2 0x07

3D Auto

View

3D Auto View: 3D Auto View value code ( 0 ~ 2 ) to be set on TV / Monitor

0x00 Off

Check

Sum

0x01 Message Notice

0x02 On

●

Get the 3D Auto View Status

Header Command

ID

0xAA

●

Ack

0xC0

Header Command

ID

0xAA 0xFF

Data Length

1

Sub Cmd

0x07

Data Length Ack/Nak

4 'A'

Check

Sum r-CMD r-SUBCMD

0xC0 0x07

Val 1

3D Auto

View

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x07

Val 1

ERR

A.C0.08 3D Optimization Control

●

Function

The PC Sets the 3D Optimization settings of a TV or monitor.

●

Set the 3D Optimization Status


0xAA

●

Ack

Header

0xC0

Check

Sum

3D Optimization: 3D Optimization value code ( 0 ~ 2 ) to be set on TV / Monitor

●

Get the

3D Optimization

Status


0xAA 0xC0

ID

1 0x08

Check

Sum

Command

ID

2 0x08

Data Length Ack/Nak

3D

Optimizatio n r-CMD r-SUBCMD

0xAA 0xFF

ID

4 'A' 0xC0 0x08

Val 1

3D

Optimizatio n

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x08

Val 1

ERR

A.C0.09 Expert Pattern Control

●

Function

The PC Sets the Expert Pattern View settings of a TV or monitor.

●

Set the Expert Pattern Status


0xAA 0xC0

ID

2 0x09

3D Expert

Pattern

Check

Sum

3D Expert Pattern: Expert Pattern value code ( 0 ~ 9 ) to be set on TV / Monitor

0x00 Off

0x01

0x02

Pattern1

Pattern2

0x03

0x04

0x05

0x06

0x07

Pattern3(Color Bar)

Pattern4(HRamp)

Pattern5(VRamp)

Pattern6(White)

Pattern7(RED)

0x08 Pattern8(BLUE)

0x09 Pattern9(Green)

●

Get the Expert Pattern Status

Header Command

ID

0xAA

●

Ack

Header

0xC0

Command

ID

0xAA 0xFF

Data Length

1

Sub Cmd

0x09

Data Length Ack/Nak

4 'A'

Check

Sum r-CMD r-SUBCMD

0xC0 0x09

Val 1

3D Expert

Pattern

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x09

Val 1

ERR

A.C0.0A RGB Mode Only Control

●

Function

The PC Sets the RGB Mode Only View settings of a TV or monitor.

●

Set the RGB Mode Only Status


0xAA 0xC0

ID

0x02 0x0A

RGB Mode

Only

Check

Sum

RGB Mode Only: RGB only mode value code ( 0 ~ 9 ) to be set on TV / Monitor

0x00 Off

0x01

0x02

Red

Green

0x03 Blue

●

Get the RGB Mode Only Status

Header Command

ID

0xAA

●

Ack

Header

0xC0

Command

ID

0xAA 0xFF

Data Length

0x01

0x04

Sub Cmd

0x0A

Data Length Ack/Nak

'A'

Check

Sum r-CMD r-SUBCMD

0xC0 0x0A

Val 1

RGB Mode

Only

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

0x04 'N'

Check

Sum


0xC0 0x0A

Val 1

ERR

A.C0.0B Color Space Control

●

Function

The PC Sets the Color Space settings of a TV or monitor.

●

Set the Color Space Status


0xAA 0xC0

ID

2 0x0B

Color

Space

Color Space: Color Space value code ( 0 ~ 2 ) to be set on TV / Monitor

0x00 Auto

0x01 Native

0x02 Custom

●

Get the Color Space Status

Header Command

ID

0xAA

●

Ack

Header

0xC0

Command

ID

0xAA 0xFF

Data Length

1

Sub Cmd

0x0B

Data Length Ack/Nak

4 'A'

Check

Sum

Check

Sum r-CMD r-SUBCMD

0xC0 0x0B

●

Nak

Check

Sum

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x0B

Val 1

Color

Space

Val 1

ERR

A.C0.0C Color Space Color Control

●

Function

The PC Sets the

Color Space

Color settings of a TV or monitor.

●

Set the Color Space Color Status


0xAA 0xC0

ID

2 0x0C

Color

Space

Color

Check

Sum

Color Space Color: Color Space Color value code ( 0 ~ 5 ) to be set on TV / Monitor

0x00 Red

0x01 Green

0x02

0x03

0x04

Blue

Yellow

Cyan

0x05 Magenta

●

Get the Color Space Color Status

Header Command

ID

0xAA

●

Ack

Header

0xC0

Command

Data Length

1

Sub Cmd

0x0C

Data Length Ack/Nak

Check

Sum r-CMD r-SUBCMD

ID

0xAA 0xFF 4 'A' 0xC0 0x0C

Val 1

Color

Space

Color

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x0C

Val 1

ERR

A.C0.0D Color Space Red Control

●

Function

The PC Sets the Color Space Red settings of a TV or monitor.

●

Set the

Color Space

Red Status


0xAA 0xC0

ID

2 0x0D

Color

Space Red

Check

Sum

Color Space Red: Color Space Red value code ( 0 ~ 100 ) to be set on TV / Monitor

●

Get the Color Space Red Status


0xC0

ID

1 0x0D

Check

Sum

0xAA

●

Ack


ID

0xAA 0xFF 4 'A' 0xC0 0x0D

Val 1

Color

Space Red

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x0D

Val 1

ERR

A.C0.0E Color Space Green Control

●

Function

The PC Sets the

Color Space

Green settings of a TV or monitor.

●

Set the Color Space Green Status


0xAA 0xC0

ID

2 0x0E

Color

Space

Green

Check

Sum

Color Space Green:

Color Space

Green value code ( 0 ~ 100 ) to be set on TV / Monitor

●

Get the Color Space Green Status


0xAA 0xC0

ID

1 0x0E

Check

Sum

●

Ack

Header Command Data Length Ack/Nak r-CMD r-SUBCMD Val 1

0xAA 0xFF

ID

4 'A' 0xC0 0x0E

Color

Space

Green

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x0E

Val 1

ERR

A.C0.0F Color Space Blue Control

●

Function

The PC Sets the

Color Space Blue

settings of a TV or monitor.

●

Set the Color Space Blue Status


0xAA 0xC0

ID

2 0x0F

Color

Space Blue

Check

Sum

Color Space Blue:

Color Space Blue

value code ( 0 ~ 100 ) to be set on TV / Monitor

●

Get the Color Space Blue Status


0xAA 0xC0

ID

1 0x0F

Check

Sum

●

Ack

Header Command Data Length Ack/Nak r-CMD r-SUBCMD Val 1

ID

0xAA 0xFF 4 'A' 0xC0 0x0F

Color

Space Blue

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x0F

Val 1

ERR

A.C0.10 Color Space Reset

●

Function

This command will reset the color space for TV or monitor.

●

Set the Color Reset


ID

0xAA 0xC0 2 0x10

●

Ack


ID

0xAA 0xFF 4 'A'

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


Data1

TBD

Check

Sum r-CMD r-SUBCMD

0xC0 0x10

Val 1

TBD r-CMD r-SUBCMD

0xC0 0x10

Val 1

ERR

A.C0.11 White Balance RGB Offset

●

Function

The PC displays the White Balance RGB Offset of a TV or monitor.

●

Set the White Balance RGB Offset


ID

0xAA 0xC0 2 0x11 R Offset

Data2

G Offset

Data3

B Offset

Check

Sum

R Offset : R Offset value code ( 0 ~ 50 ) to be set on TV / Monitor

G Offset : G Offset value code ( 0 ~ 50 ) to be set on TV / Monitor

B Offset : B Offset value code ( 0 ~ 50 ) to be set on TV / Monitor

●

Get the White Balance RGB Offset


0xC0

ID

1 0x11

Check

Sum

0xAA

●

Ack


ID


Data2 Data3

G Offset B Offsett

●

Nak

Header Command

0xAA 0xFF

Check

Sum

ID

Data Length Ack/Nak

4 'N' r-CMD r-SUBCMD

0xC0 0x11

Check

Sum


Data1

R Offset

Val 1

ERR

A.C0.12 White Balance RGB Gain

●

Function

The PC displays the White Balance RGB Gain of a TV or monitor

●

Set the White Balance RGB Gain


ID

0xAA 0xC0 0x04 0x12 R Gain

Data2

G Gain

Data3

B Gain

Check

Sum

R Gain : R Gain value code ( 0 ~ 50 ) to be set on TV / Monitor

G Gain : G Gain value code ( 0 ~ 50 ) to be set on TV / Monitor

B Gain : B Gain value code ( 0 ~ 50 ) to be set on TV / Monitor

●

Get the White Balance RGB Gain


ID

Check

Sum

0xAA 0xC0 0x01 0x12

●

Ack

Header Command

ID

Data Length Ack/Nak r-CMD r-SUBCMD

0xAA 0xFF 0x06 'A' 0xC0 0x12

Data2

G Gain

●

Nak

Header

0xAA

Data3

B Gain

Command

0xFF

Check

Sum

ID

Data Length Ack/Nak

0x04 'N' r-CMD r-SUBCMD

0xC0 0x12

Check

Sum


Data1

R Gain

Val 1

ERR

A.C0.13 White Balance Reset

●

Function

This command will reset the White Balance for a TV or monitor.

●

Set the White Balance Reset


ID

0xAA 0xC0 2 0x13 TBD

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak


0xC0

Check

Sum

0x13

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x13

Val 1

TBD

Val 1

ERR

A.C0.14 Set Flesh Tone

●

Function

This command will set the Flesh Tone for a TV or monitor.

●

Set the Flesh Tone


ID

0xAA 0xC0 2 0x14 Flesh Tone

Flesh Tone: Flesh Tone value code ( 0 ~ 30 ) to be set on TV / Monitor

●

Get the Flesh Tone


0xC0

ID

1 0x14

Check

Sum

0xAA

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak


0xC0

Check

Sum

0x14

Val 1

Flesh Tone

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x14

Val 1

ERR

A.C0.15 Set motion Lighting

●

Function

This command will set the Motion Lighting for a TV or monitor.

●

Set the Motion Lighting


0xAA 0xC0

ID

2 0x15

Motion

Lighting

Check

Sum

Motion Lighting: Motion Lighting value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00 Off 0x01 On

●

Get the Motion Lighting


0xAA 0xC0

ID

1 0x15

Check

Sum

●

Ack


ID


Val 1

Motion

Lighting

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x15

Val 1

ERR

A.C0.16 Set LED Motion Plus

●

Function

This command will set the LED Motion Plus for a TV or monitor.

●

Set the LED Motion Plus

5

Command

ID

Data Length Sub Cmd Data1

0xAA 0xC0 2 0x16

LED Motion

Plus

Check

Sum

LED Motion Plus: LED Motion Plus value code ( 0 ~ 3 ) to be set on TV / Monitor

0x00 Off

0x01

0x02

0x03

●

Get the LED Motion Plus

Header Command

Normal

Cinema

Ticker

ID

0xAA

●

Ack

Header

0xC0

Command

ID

0xAA 0xFF

Data Length

1

4

Sub Cmd

0x16

Data Length Ack/Nak

'A'

Check

Sum r-CMD r-SUBCMD

0xC0 0x16

Val 1

LED Motion

Plus

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x16

Val 1

ERR

A.C0.17 Set MPEG Noise Filter

●

Function

This command will set the MPEG Noise Filter for a TV or monitor.

●

Set the MPEG Noise Filter


0xAA 0xC0

ID

2 0x17

MPEG

Noise Filter

Check

Sum

MPEG Noise Filter: MPEG Noise Filter value code ( 0 ~ 4 ) to be set on TV / Monitor

0x00

Off

0x01

0x02

0x03

Low

Medium

High

0x04

Auto

●

Get the MPEG Noise Filter


ID

Check

Sum

0xAA

●

Ack

Header

0xC0

Command

1 0x17

Data Length Ack/Nak

0xAA 0xFF

ID


0xC0 0x17

Val 1

MPEG

Noise Filter

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x17

Val 1

ERR

A.C0.18 Set Smart LED

●

Function

This command will set the Smart LED for a TV or monitor.

●

Set the Smart LED


0xAA 0xC0

ID

2 0x18

SMART

LED

SMART LED: Smart LED value code ( 0 ~ 4 ) to be set on TV / Monitor

0x00 Off

0x01

0x02

Low

Standard

0x03 High

0x04

●

Get the Smart LED

Header

Demo

Command Data Length Sub Cmd

ID

Check

Sum

0xAA

●

Ack

Header

0xC0

Command

1 0x18

Data Length Ack/Nak

Check

Sum r-CMD r-SUBCMD

ID


Val 1

SMART

LED

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x18

Val 1

ERR

A.C0.19 Set Cinema Black

●

Function

This command will set the Cinema Black for a TV or monitor.

●

Set the Cinema Black


0xAA 0xC0

ID

2 0x19

CINEMA

BLACK

Check

Sum

CINEMA BLACK: Cinema Black value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00

Off 0x01 On

●

Get the Cinema Black


ID

Check

Sum

0xAA

●

Ack

Header

0xC0

Command

1 0x19


ID


Val 1

CINEMA

BLACK

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x19

Val 1

ERR

A.C0.1A Marker On/Off

●

Function

This command will On/Off the Marker for a TV or monitor.

●

Set the Marker


0xAA 0xC0

ID

2 0x1A

MARKER

ON/OFF

Check

Sum

MARKER ON/OFF: Marker On Off value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00 Off 0x01 On

●

Get the Marker


ID

Check

Sum

0xAA

●

Ack

Header

0xC0

Command

1 0x1A


ID

0xAA 0xFF 4 'A' 0xC0 0x1A

Val 1

MARKER

ON/OFF

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1A

Val 1

ERR

A.C0.1B Set Overlay Aspect Ratio

●

Function

This command will set the Overlay aspect ratio for a TV or monitor.

●

Set the Overlay Aspect Ratio


0xAA 0xC0

ID

2 0x1B

Overlay

Aspect

Ratio

Check

Sum

Overlay Aspect Ratio: Overlay Aspect ratio value code ( 0 ~ 9 ) to be set on TV / Monitor

0x00 OFF

0x01

0x02

0x03

0x04

16:9

4:3

15:9

14:9

0x05

0x06

0x07

13:9

1.85:1

2.35:1

0x08 1.85:1 & 4:3

●

Get the Overlay Aspect Ratio

Header Command

ID

0xAA

●

Ack

Header

0xC0

Command

Data Length

1

Sub Cmd

0x1B

Data Length Ack/Nak

Check

Sum r-CMD r-SUBCMD

0xAA 0xFF

ID

4 'A' 0xC0 0x1B

Val 1

Overlay

Aspect

Ratio

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1B

Val 1

ERR

A.C0.1C Set Cross Marker

●

Function

This command will set the cross marker for a TV or monitor.

●

Set the Cross Marker


0xAA 0xC0

ID

2 0x1C

Cross

Marker

Cross Marker: Cross Marker value code ( 0 ~ 1 ) to be set on TV / Monitor

0x00 Off 0x01 On

Check

Sum

●

Get the Cross Marker


ID

Check

Sum

0xAA

●

Ack

Header

0xC0

Command

1 0x1C


ID

0xAA 0xFF 4 'A' 0xC0 0x1C

Val 1

Cross

Marker

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1C

Val 1

ERR

A.C0.1D Set Safety Area

●

Function

This command will set the Safety Area for a TV or monitor.

●

Set the Safety Area


ID

0xAA 0xC0 2 0x1D

Data1

Safety Area

Safety Area : Cross Marker value code ( 0 ~ 5 ) to be set on TV / Monitor

●

Get the Safety Area


0xAA 0xC0

ID

1 0x1D

Check

Sum

●

Ack

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak


0xC0

Check

Sum

0x1D

Val 1

Safety Area

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1D

Val 1

ERR

A.C0.1E Set Black Matte

●

Function

This command will set the Safety Area for a TV or monitor.

●

Set the Black Matte


ID

0xAA 0xC0 2 0x1E

Data1

Black Matte

Black Matte : Black Matte value code ( 0 ~ 2 ) to be set on TV / Monitor

●

Get the Black Matte


ID

Check

Sum

0xAA

●

Ack

Header

0xAA

0xC0

Command

0xFF

ID

1 0x1E

Data Length Ack/Nak


0xC0

Check

Sum

0x1E

Val 1

Black Matte

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1E

Val 1

ERR

A.C0.1F Set Marker Color

●

Function

This command will set the Marker Color for a TV or monitor.

●

Set the Marker Color


ID

0xAA 0xC0 2 0x1F

●

Get the Marker Color


ID

0xAA 0xC0 1 0x1F

●

Ack

Header Command

ID

Data Length Ack/Nak

0xAA 0xFF 4 'A'

Data1

Check

Sum

Check

Sum r-CMD r-SUBCMD

0xC0 0x1F

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x1F

Val 1

TBD

Val 1

ERR

A.C0.20 Set Marker Thickness

●

Function

This command will set the Marker Thickness for a TV or monitor.

●

Set the Marker Thickness


0xAA 0xC0

ID

2 0x20

Marker

Thickness

Check

Sum

Marker Thickness : Marker Thickness value code ( 0 ~ 7 ) to be set on TV / Monitor

●

Get the Marker Thickness


0xAA 0xC0

ID

1 0x20

Check

Sum

●

Ack


ID


Val 1

Marker

Thickness

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0x20

Val 1

ERR

A.C0.A0 Send Calibration Command

●

Function

This command will send the start command for a TV or monitor.

●

Set the Calibration Command


0xAA 0xC0

ID

2 0xA0

Start

Command

Check

Sum

Start Command : Start Command value code ( 0 ~ 2 ) to be set on TV / Monitor

0x00 Start

0x01 Stop

0x02 Finish

●

Get the Calibration Command

Header Command

ID

0xAA 0xC0

●

Ack

Header Command

ID

0xAA 0xFF

Data Length

1

Sub Cmd

0xA0

Data Length Ack/Nak

4 'A'

Check

Sum r-CMD r-SUBCMD

0xC0 0xA0

Val 1

Start

Command

Check

Sum

●

Nak

Header

0xAA

Command

0xFF

ID

Data Length Ack/Nak

4 'N'

Check

Sum


0xC0 0xA0

Val 1

ERR

Annex B. Model dependency

B.1 PIC_MODE definition

●

A model which is support **** Text , **** Video/Image and Calibration as picture mode on the menu

1. If the picture mode on the menu is calibration, it will be treat as PIC_MODE_CALIB

In case of picture mode in the menu is not calibration

2. If current source is AV, TV or Component then the picture mode is treat as PIC_MODE_VIDEO regardless picture mode on the menu

3. If current source is PC then the picture mode is treat as PIC_MODE_PC regardless picture mode on the menu

4. if current source is others(not listed in 2 or 3) then it will be treat as PIC_MODE_VIDEO when the picture mode in the menu is *** Video/Image or treat as PIC_MODE_PC when the picture mode in the menu is *** Text.

B.2 H-Position Control

●

Function

Personal Computer adjusts Horizontal Position of TV / Monitor.

●

Working Condition



- HKIA support option is on

●

Get H-Position Status

Header

Command

ID

Data Length

Check

Sum

0xAA 0x31 0x00

●

Set H-Position


0xAA 0x31

ID

0x01 H-Pos

Check

Sum

H-Pos : Value of 0 ~ 100

0 leftside max position

1 ~ 49 percentage position between leftside max ~ default

50 default position

51 ~ 99 percentage position between default ~ rightnside max

100

●

Ack

Header rightnside max position

Command Data Length Ack/Nak r-CMD

ID

0xAA 0xFF

H-Pos : Same as above

●

Nak

Header Command

0x03 'A'

Data Length Ack/Nak

0x31 r-CMD

ID

0xAA 0xFF 0x03 'N' 0x31


Val 1

H-Pos

Val 1

ERR

Check

Sum

Check

Sum

B.3 V-Position Control

●

Function

Personal Computer adjusts Vertical Position of TV/Monitor.

●

Working Condition



- HKIA support option is on

●

Get V-Position Status


0xAA 0x32

ID

0x00

Check

Sum

●

Set V-Position


0xAA 0x32

ID

0x01 V-Pos

Check

Sum

V-Pos : Value of 0 ~ 100

0 upside max position

1 ~ 49 percentage position between upside max ~ default

50 default position

51 ~ 99 percentage position between default ~ downside max

100 downside max position

●

Ack


ID

0x03 'A' 0xAA 0xFF

V-Pos : Same as above

●

Nak


ID

0xAA 0xFF 0x03 'N' r-CMD

0x32 r-CMD

0x32


Val 1

V-Pos

Val 1

ERR

Check

Sum

Check

Sum

Multiple Display Control Protocol

SEC-VD-DSW Multiple Display Control

Ver. 14.1c

2017-04-20

Multiple Display Control Protocol

SEC-VD-DSW Multiple Display Control

Ver. 14.1c

2017-04-20

0

Copyright notice

This document is Copyright © Samsung Electronics, Co. - all rights reserved.

1. INTERFACE

1.1. Connection Method

There are 2 available ways of connecting. one is RS232, the other is RJ45.

1.2. Connection Spec

-

→

2. Command

2.1 Common Protocol

:

T

:

:

-

Video Wall User Control

Video Wall User Control

Input Source Control (MFM)

.

Not Support

Input Source Control (MFM)

Annex A. Reference TV MDC Command

3D Effect

3D Effect

3D Optimization

Color Space

Color Space

Color Space

Color Space

Color Space Blue

Color Space Blue

Annex B. Model dependency

Related manuals

Samsung

700DRN

Sony

PFM-42V1

Infocus

TD30

Sony

FWD-S47H1

Samsung

403t

Samsung

320PX

Sony

fwd-50px2

Sony

FWD-50PX1

Sony

FWD-42PX2

Dell

D7523QT