Panasonic CQVD7003N Operating Instructions
Add to my manuals22 Pages
Panasonic CQ-VD7003N
This guide provides crucial information to help you get the most out of your Panasonic CQ-VD7003N. By following these instructions, you can ensure safe and effective operation.
Key Features:
- Negative grounded 12 V DC battery system compatibility
- Protection against electrical shock and injury due to short circuits
- Safety precautions for installation, grounding, and other functions
- Prevention of airbag interference during installation
- Avoidance of potential hazards from piping, gasoline tank, electric wiring, and other vehicle components
- Assurance of normal operation of other electrical equipment after installation and wiring
advertisement
▼
Scroll to page 2
of 22
English Safety Information 1 ■ Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual. Warning This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in severe injury or death. Warning Observe the following warnings when using this unit. ❑ The driver should neither watch the display nor operate the system while driving. Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents. Always stop the vehicle in a safe location and use the parking brake before watching the display or operating the system. ❑ Use the proper power supply. This product is designed for operation with a negative grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system. ❑ Keep batteries and insulation film out of reach of infants. Batteries and insulation film can be ingested, so keep them out of the reach of infants. If an infant ingests a battery or insulation film, please seek immediate medical attention. ❑ Protect the Deck Mechanism. Do not insert any foreign objects into the slot of this unit. ❑ Do not disassemble or modify the unit. Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Service Centre. ❑ Do not use the unit when it is out of order. If the unit is out of order (no power, no sound) or in an abnormal state (has foreign objects in it, is exposed to water, is smoking, or smells), turn it off immediately and consult your dealer. ❑ The remote control unit should not lie about in the car. If the remote control unit lies about, it could fall on the floor while driving, get wedged under the brake pedal, and lead to a traffic accident. ❑ Refer fuse replacement to qualified service personnel. When the fuse blows out, eliminate the cause and have it replaced with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire, and damage to the product. 2 CQ-VD7003N ■ This manual uses pictographs to show you how to use the product safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly. Caution This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in injury or material damage. Observe the following warnings when installing. ❑ Disconnect the lead from the negative (–) battery terminal before installation. Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit. Some cars equipped with the electrical safety system have specific procedures of battery terminal disconnection. FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH. ❑ Never use safety-related components for installation, grounding, and other such functions. Do not use safety-related vehicle components (fuel tank, brake, suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories. ❑ Installing the product on the air bag cover or in a location where it interferes with airbag operation is prohibited. ❑ Check for piping, gasoline tank, electric wiring, and other items before installing the product. If you need to open a hole in the vehicle chassis to attach or wire the product, first check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole from outside if possible. ❑ Never install the product in a location where it interferes with your field of vision. ❑ Never have the power cord branched to supply other equipment with power. ❑ After installation and wiring, you should check the normal operation of other electrical equipment. The continuation of their using in abnormal conditions may cause fire, electrical shock or a traffic accident. ❑ In the case of installation to an airbag-equipping car, confirm warnings and cautions of the vehicle manufacturer before installation. ❑ Make sure the leads do not interfere with driving or getting in and out of the vehicle. ❑ Insulate all exposed wires to prevent short circuiting. Observe the following cautions when using this unit. ❑ Keep the sound volume at an appropriate level. Keep the volume level low enough to be aware of road and traffic conditions while driving. ❑ Do not insert or allow your hand or fingers to be caught in the unit. To prevent injury, do not get your hand or fingers caught in moving parts or in the disc slot. Especially watch out for infants. ❑ This unit is designed for use exclusively in automobiles. ❑ Do not operate the unit for a prolonged period with the engine turned off. Operating the audio system for a long period of time with the engine turned off will drain the battery. ❑ Do not expose the unit to direct sunlight or excessive heat. Otherwise these will raise the interior temperature of the unit, and it may lead to smoke, fire, or other damage to the unit. ❑ Do not use the product where it will be exposed to water, moisture, or dust. Exposure of the unit to water, moisture, or dust may lead to smoke, fire, or other damage to the unit. Make especially sure that the unit does not get wet in car washes or on rainy days. Observe the following cautions when installing. ❑ Refer wiring and installation to qualified service personnel. Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your own installation of the unit. ❑ Follow the instructions to install and wire the product. Not following the instructions to properly install and wire the product could cause an accident or fire. ❑ Take care not to damage the leads. When wiring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, screws, and moving parts such as seat rails. Do not scratch, pull, bend or twist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by winding them with vinyl tape or similar protection. ❑ Use the designated parts and tools for installation. Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or fire. English Caution 2 ❑ Do not block the air vent or the cooling plate of the unit. Blocking these parts will cause the interior of the unit to overheat and will result in fire or other damage. ❑ Do not install the product where it is exposed to strong vibrations or is unstable. Avoid slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall down while driving and this can lead to an accident or injury. ❑ Installation Angle The product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚. The user should bear in mind that in some areas there may be restrictions on how and where this unit must be installed. Consult your dealer for further details. ❑ Wear gloves for safety. Make sure that wiring is completed before installation. ❑ To prevent damage to the unit, do not connect the power connector until the whole wiring is completed. ❑ Do not connect more than one speaker to one set of speaker leads. (except for connecting to a tweeter) Observe the following cautions when handling the battery for the remote control unit. ● Use only specified battery (CR2025). ● Match the polarity of the battery with the (+) and (–) marks in the battery case. ● Replace a dead battery as soon as possible. ● Remove the battery from the remote control unit when not using it for an extended period of time. ● Insulate the battery (by placing them in a plastic bag or covering them with vinyl tape) before disposal or storage. ● Dispose of the battery according to the local regulations. ● Do not disassemble, recharge, heat or short the battery. Do not throw a battery into a fire or water. In case of battery leakage ● Thoroughly wipe the battery liquid off the battery case and insert new battery. ● If any part of your body or clothing comes into contact with battery liquid, wash it with plenty of water. ● If battery liquid comes into contact with your eyes, wash them with plenty of water and get immediate medical attention. CAUTION: • PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING, INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED. CQ-VD7003N 3 English Before Reading These Instructions 3 Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family. This is a guide book specific to system upgrading. Please refer to the operating instructions for basic operations, menu operations, specifications, etc. System upgrade sample TV Tuner (CY-TUP153N, option) Display Unit Rear Monitor CQ-VD7003N iPod® Hands-Free Kit featuring Bluetooth® technology (CY-BT100N, option) Expansion Module (CY-EM100N, option) CD Changer (CX-DP880N, option) DVD Changer (CX-DH801N, option) Car Navigation System (CN-DV2300N, option) 4 CQ-VD7003N English Connectable devices ■ DVD Changer ■ Hands-Free Phone System The optional adapter (Conversion Cable for DVD/CD Changer: CA-CC30N) allows you to connect the optional Panasonic DVD changer unit (CX-DH801N). For details, refer to the operating instructions for the DVD changer unit. You can connect the optional Hands-Free Phone System (Hands-Free Kit featuring Bluetooth® technology: CY-BT100N). For details, refer to the operating instructions for the Hands-Free Phone System. Note: This unit is designed only for receiving calls. It cannot send calls. Bluetooth® The Bluetooth word mark and logo are owned by the Bluetooth SIG, Inc. and any use of such marks by Matsushita Electric Industrial Co.,Ltd. is under license. Other trademarks and trade name are those of their respective owners. ■ CD Changer The optional adapter (Conversion Cable for DVD/CD Changer: CA-CC30N) allows you to connect the optional Panasonic CD changer unit (CX-DP880N). For details, refer to the operating instructions for the CD changer unit. ■ TV tuner You can connect the optional Panasonic TV tuner unit (CYTUP153N). For details, refer to the operating instructions for the TV tuner unit. ■ iPod® The optional adapter (Direct Cable for iPod: CA-DC300N) allows you to connect the optional iPod series. The iPod equipped with a dock connector is exclusively connectable. Further information about the controllable iPod is described below. Controllable iPod/software version ¡ 3rd generation iPod/ver. 2.3 ¡ 4th generation iPod/ver. 3.1 ¡ iPod Photo/ver. 1.2 ¡ iPod mini/ver. 1.4 ¡ iPod nano/ver. 1.0 * Operation check has been completed with software available at the end of October, 2005. We do not guarantee the operation with our future products or upgraded software. iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. 4 ■ Expansion Module (hub unit) You can connect the optional Expansion Module (hub unit) (CY-EM100N). Connection of the Expansion Module allows you to simultaneously connect optional devices mentioned before as well as other AV devices. For details, refer to the operating instructions for the Expansion Module. Connectable devices ¡ CD/DVD changer (max. 1) ¡ iPod (max. 2) ¡ Hands-Free Phone System (max. 1) ¡ TV tuner (max. 1) Note: Market conditions regarding optional devices vary with countries and regions. For further information, consult your dealer. CQ-VD7003N 5 English Before Reading These Instructions (continued) 5 System upgrade sample ■ Simultaneous Multi-Device Connection CQ-VD7003N CD Changer (CX-DP880N, option) DVD Changer (CX-DH801N, option) System-up Connector Only 1 unit Conversion Cable for DVD/CD Changer (CA-CC30N, option) iPod Up to 4 units Direct cable for iPod (CA-DC300N, option) Expansion Module (CY-EM100N, option) Note: ¡ Refer to individual instruction and installation manuals for each device for detailed installation and wiring. Cellular Phone CY-BT100U Hands-Free Kit featuring Bluetooth® technology (CY-BT100N, option) TV Tuner (CY-TUP153N, option) 6 CQ-VD7003N English ■ 5.1-channel Surround System This unit has a built-in 4-channel amplifier. The procedure for setting up a 5.1-channel surround system in order to play DVD software in a way that creates a “you are there” feel in a car is described below. 6 Note: ¡Even if you are using this unit without installing a centre speaker, surround speakers, or a subwoofer, it is still necessary to make the speaker settings in order to adjust the sound balance. Centre Speaker: EAB-CF2 Panasonic Power amplifier CQ-VD7003N Front Speakers: CJ-DA1733 Surround Speakers: CJ-DA6923 Power amplifier Subwoofer: CJ-SW3003 Contents Common Safety Information................................................2 Before Reading These Instructions....................4 Contents................................................................7 Touch Panel Operation Overview.......................8 Settings Settings ...............................................................20 As needed Troubleshooting.................................................22 Each Source TV Tuner Control................................................10 CD Changer Control...........................................12 DVD Changer Control ........................................13 Car Navigation System ......................................15 Bluetooth Hands-Free Kit .................................16 iPod Control........................................................18 CQ-VD7003N 7 English Touch Panel Operation Overview 7 ❒ Notes on the Touch Panel Before operation ¡Clean the surface of the touch panel. (a Operating Instructions) Operation ¡Use only your fingers to operate the touch panel. ¡Do not press the panel forcefully. ¡Do not scratch the panel with fingernails or any hard objects. ¡Do not use a pen or other sharp implements to operate the touch panel. ¡Do not bump the front panel. a Failure to observe the above may damage or break the glass on the surface of the touch panel. Note: ¡The navigation system (CN-DV2300N, option) is not operable with the touch panel of this unit. The State of Operation Screen Example: CD Changer Note: ¡The following picture is partly darkened for explanation. ¡Displaying contents and their positions partly vary with each mode. Refer to the description of each mode for details. Display Button (a next page) Source Button Menu Button (Content varies with each source) Displays the Source Selection Screen. Displays the Menu Screen. Source Selection Screen Source Selection Screen appears. Touch desired source button. Touch to quit. Menu Screen Menu Screen appears. Select desired setting. Menu Setting, (a Operating Instructions) Press [SRC] to change to desired mode. Note: ¡When an , , or is connected to this unit without involving the Expansion Module (CYEM100N, option), any of them appears at the AV2 position. 8 CQ-VD7003N Press [MENU] to let Menu Screen appear. ¡When is selected on the condition that the Expansion Module is connected to this unit, the video and audio of the source connected to AUDIO IN/VIDEO IN of the Expansion Module come out. English Switching the display Touching allows users to switch between screens as follows. ❏ How to Call up Operation Screen Source Standard Screen 8 Operation Screen CD Changer (a page 12) iPod (a page 18) ❏ How to Cancel OSD (On Screen Display) Source Standard Screen OSD OFF *2 TV tuner (*1) (a page 10) DVD Changer (*1) (a page 13) *1 To switch Operation Screen ON, touch the center of touch panel or press [ENTER]. *2 The operation screen is not available in the video mode. Note: ¡Refer to the description of each mode for how to operate the operation screen. CQ-VD7003N 9 English TV Tuner Control 9 Preparation: ¡Connect a TV tuner (CY-TUP153N, option) to the unit. ¡It is required to install the TV antenna to receive TV broadcasts. TV Mode Selection ¡For receiving TV broadcasts, stop your car where there is no obstacle to broadcast reception around. Source Button q Touch “Source Button”. TILT CLOSE d (TV) w Touch on the Source Selection Screen. (Content varies with connected devices) Channel selection/ Channel seeking TV menu Preset channel selection OPEN / CLOSE ASPECT ASP Press [SRC] to change to the TV mode. CQ-VD7003N TILT O/C TEXT P·MODE CQ-VD7001U Band selection VOL ENTER To switch Operation Screen ON, touch the center of touch panel or press [ENTER]. MUTE PWR SRC TA NAVI [SRC] Note: ¡For the operations of the TV tuner with its remote control, aim the remote control at the remote control sensor of this unit. ¡The remote control of the TV tuner (CY-TUP153N, option) cannot turn on or off the power of the TV tuner. [ENTER] [] ] [[ ] [}] [{] Tuning Operations Band Selection [BAND] [ENTER] END DVD VTR RADIO CH-C TV 1 Channel Selection [[] [[] Up []] []] Down Channel Seeking [[] [[] Up []] []] Down – – [}] [{] [}] [{] Up/down [] ] [[ ] [] ] [[ ] Left/right Displaying TV Menu Selecting an Item on the TV Menu …… Touch/Press and hold 10 TV 2 CQ-VD7003N Calls up the menu of the tuner. To cancel, touch again. English Preset Memory Operations Auto Preset Memory 12 channels with first to 12th highest in signal strength will be preset to each band. 10 END [BAND] DVD VTR RADIO CH-C [ENTER] Select a band. ¡Touch/press and hold for more than 2 seconds. ¡ “–” appears if the number of receivable channels is less than 12. New channels overwrite existing saved channels. Writing Preset Memory Favorite preset channels can be written after you have set the preset channel once. Select a band and a channel. d Preset Channel Calling Favorite preset channels can be deleted after you have set the preset channel once. [}] d d ¡Preset channel writing mode display appears. d Deleting Preset Memory [}] [] ] [[ ] [] ] [[ ] d d [BAND] [ENTER] – – Select a channel that you want to exchange. Determine. ¡Exit from the preset writing. [}] [}] Down [{] [{] Up Select a band and a channel. d [{] [{] d d ¡Preset channel deleting mode display appears. d [}] [{] [}] [{] d d [BAND] [ENTER] – – Select a preset number that you want to delete. Determine. ¡Exit from the preset channel deletion. …… Touch/Press and hold for more than 2 seconds CQ-VD7003N 11 English CD Changer Control 11 ¡CD changer functions are designed for optional Panasonic CD changer unit. (CX-DP880N) Preparation: ¡Connect the CD changer, and load a magazine (discs). Source Button Current track CD Changer Mode Selection q Touch “Source Button”. d TILT CLOSE Disc number (CHw Touch C) on the Source Selection Screen. (Content varies with connected devices) Title scroll OPEN / CLOSE ASPECT ASP CQ-VD7003N TILT O/C TEXT P·MODE Press [SRC] to change to the CD Changer mode. CQ-VD7001U Random Play Scan Play Repeat Play VOL ENTER MUTE PWR SRC TA NAVI [SRC] Disc selection Track selection [] ] [[ ] [}] [{] Basic Operations Operations Disc Selection [}] [}] Next disc [{] Previous disc [d] [[] [s] []] [d] [[] [s] []] Next track Beginning of the current track Previous track (Touch/press twice.) Fast forward Release to resume playback. Fast reverse Release to resume playback. – – To cancel, touch again. – – To cancel, touch and hold for more than 2 seconds again. – – To cancel, touch again. – – The first 10 seconds of the all the discs is played. To cancel, touch and hold for more than 2 seconds again. – – To cancel, touch again. – – To cancel, touch and hold for more than 2 seconds again. – – Scrolls the title once [{] Track Selection Fast Forward/ Fast Reverse Repeat Play Repeat Play within the current Disc * Scan Play Disc Scan Play * Random Play Random Play within the Current Disc Title Scroll …… Touch/Press and hold 12 CQ-VD7003N * END DVD VTR RADIO CH-C * Touch panel symbols will change to indicate these current mode. , , {D= DISC (disc)} Preparation: ¡Connect the DVD changer, and load a magazine (discs). ¡DVD changer functions are designed for optional Panasonic DVD changer unit. (CX-DH801N) DVD Changer Mode Selection English DVD Changer Control 12 q Touch “Source Button”. d Source Button (CHw Touch C) on the Source Selection Screen. (Content varies with connected devices) TILT CLOSE Operation Buttons Press [SRC] to change to the DVD Changer mode. Disc/folder selection OPEN / CLOSE ASPECT ASP CQ-VD7003N TILT O/C TEXT P·MODE To switch Operation Screen ON, touch the center of touch panel or press [ENTER]. CQ-VD7001U VOL ENTER MUTE Note: ¡Be sure to connect RCA cord (video)(yellow) of the Panasonic DVD Changer to AV2-IN and set CH VIDEO INPUT to ON (a page 20). Otherwise the changer cannot be controlled through this unit. ¡Refer to the operating instructions and installation instructions of CX-DH801N as well. PWR SRC TA NAVI [SRC] [ENTER] [] ] [[ ] [}] [{] Basic Operations Operations Operations Track/file Selection Compatible Discs DVD VCD [d] CD [s] MP3 DVD Fast Forward/ Fast Reverse DVD VCD CD Folder Selection MP3 – Next track/file – Beginning of the current track/file Previous track/file (Touch/press twice.) END DVD VTR RADIO CH-C Note: ¡When playing a DVD, there are cases where it is not possible to return to the start of a chapter that spans 2 titles. (a Operating Instructions) Fast forward Release to resume playback. Fast reverse [s] – Release to resume playback. The speed changes if the button is held down as follows. Regular speed / 2 times / 5 times / 10 times / 30 times [d] – – – Next folder – – Previous folder [3] – To resume playback, touch/press / [5]. [y] – To resume playback, touch/press / [5]. MP3 DVD VCD Stop CD Pause MP3 DVD VCD CD MP3 …… Touch/Press and hold CQ-VD7003N 13 English DVD Changer Control (continued) Basic Operations (continued) Slow Playback [d] DVD VCD [d] 13 ¡Touch/press and hold in the pause mode. Playback is at about 1/4 normal speed. To resume normal playback, touch/press / [5]. Note: ¡Reverse slow playback is not possible. Disc Selection DVD VCD – – Next disc CD – – Previous disc MP3 …… Touch/Press and hold Chapter/title/track Selection Showing menu and selecting an item * Note on VCD: For VCD, press [RETURN] instead of [DVD MENU] . 14 CQ-VD7003N DVD VCD * – [DVD MENU] – d d []] [[] []] [[] [}] [{] [}] [{] d d q Menu appears. [ENTER] [ENTER] e Determine the setting. [RETURN] Returns to the previous display. – d w Select the desired item. d Preparation: ¡Connect the Car Navigation System. ¡Specify the correct terminal that is connected to the car navigation system in the NAVI INPUT Car Navigation Mode Selection English Car Navigation System . (a page 20) TILT CLOSE 14 Press [NAVI] to change to the car navigation mode. Press [NAVI] again to cancel. To switch Operation Screen ON, press [ENTER]. Note: ¡If the navigation mode is ON, only the audio signal is switched while the video signal remains as it is. ¡The volume of the voice guidance from the car navigation system can be set. (a page 20) ¡Press [NAVI] after making sure that the power button on the main unit is set to on. Pressing [NAVI] allows the navigation mode to be activated even if the power button of the main unit is set to off, but operations may be different from those in other modes in this case. ¡The position adjustment of navigation screen shall be performed at the navigation unit side. OPEN / CLOSE ASPECT ASP CQ-VD7003N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER MUTE PWR SRC TA NAVI NAVI [NAVI] [ENTER] Connecting with Panasonic Car Navigation System (e.g. CN-DV2300N, option) Connect a Panasonic car navigation system to RGB connector. CQ-VD7003N 15 English Bluetooth Hands-Free Kit 15 Preparation: ¡Connect the Bluetooth hands-free kit (CY-BT100N) and establish the pairing. Refer to the instruction manual for the Bluetooth hands-free kit for further information. Connection of the optional Bluetooth hands-free kit allows users to talk on a handsfree cellular phone in a car. Note: ¡CY-BT100N is designed only for receiving calls. It cannot send calls. Bluetooth Hands-Free Mode This mode is not selectable by pressing [SRC] or touching an item on the panel, but activated by receiving an incoming call. (To pick up the phone, press [Hang-on] on the hands-free kit.) Note: ¡ The telephone number of the calling party is displayed. ¡ “CONNECT” is displayed when information of the calling party cannot be acquired. ¡ We shall not guarantee all the functions of the Bluetooth-ready mobile phone to be connected. TILT O/C TEXT ENTER MUTE [Hang-up]/Red LED When receiving a call... CQ-VD7003N TILT CQ-VD7001U VOL [Hang-on]/Blue LED 16 CQ-VD7003N P·MODE Status indicator (Blue LED) Lights: Call waiting/Talking Stays out: Not connected Blinks rapidly: Receiving a call Blinks slowly: Pairing/Reconnecting Example: DVD mode OPEN / CLOSE ASPECT ASP [VOL] Switch unit CLOSE PWR SRC TA NAVI [] ] [[ ] English Useful Function Operations Adjustment of Ring Volume 16 Adjust the volume when a call is comming in. END – When the ringtone is the same as that of the cellular phone, DVD VTR RADIO CH-C down [–] [VOL] – [+] up [VOL] When the ringtone is not the same as that of the cellular phone (but this unit-specific sound), Adjust the volume when a call is comming in. [–] or []] mute [VOL] [+] or [[] ¡ Adjustment of phone receiver volume on [VOL] and appear only at no-inband ringing. The buttons disappear when communication starts. – down [–] [VOL] – [+] [VOL] Back to Previous Source – – – up ¡Press [Hang-Up] on the hands-free kit. ¡When [Hang-up] on the hands-free kit is pressed to hang up the phone, the previous mode resumes. Note: ¡ Reception of a call during the camera or navigation system is activated does not call up the Hands Free screen but displays only the telephone number of the calling party. Pressing [Hang-on] deletes the telephone number from the screen. does not appear. ¡ Reception of a call at MUTE-on temporarily cancels the mute function and disables operations. After end of phone communication, the mute function resumes. ¡ Source change and AUDIO -related operations in the menu are not feasible during reception of a call. But volume is adjustable and the power can be turned off even during reception of a call. ¡ Reception of a call at power-off does not turn on the power of this unit. CQ-VD7003N 17 English iPod Control 17 Preparation: ¡Connect the iPod through connecting cable (CA-DC300N, option). iPod Mode Selection Source Button q Touch “Source Button”. Information of current track/file TILT CLOSE d w Touch (iPod) on the Source Selection Screen. (Content varies with connected devices) text/title scroll operation buttons OPEN / CLOSE ASPECT ASP Press [SRC] to change to the iPod mode. CQ-VD7003N TILT O/C TEXT P·MODE CQ-VD7001U VOL ENTER To switch Operation Screen ON, touch MUTE . PWR SRC TA NAVI [SRC] [] ] [[ ] [}] [{] Note: ¡ “NO iPod” appears until the iPod is recognized after connecting the iPod, turning on the power of the main unit, or performing source selection on the main unit side. This indicates there is nothing wrong with the main unit. ¡ We shall not guarantee all the functions of the iPod to be connected. ¡ The iPod equipped with a dock connector is exclusively connectable. Controllable iPod/software version ¡ 3rd generation iPod/ver. 2.3 ¡ 4th generation iPod/ver. 3.1 ¡ iPod Photo/ver. 1.2 ¡ iPod mini/ver. 1.4 ¡ iPod nano/ver. 1.0 * Operation check has been completed with software available at the end of October, 2005. We do not guarantee the operation with our future products or upgraded software. Basic Operations Operations Track/file Selection [[] Next track/file []] Beginning of the current track/file Previous track/file (Touch/press twice.) [d] [[] [s] []] Fast forward Release to resume playback. Fast reverse Release to resume playback. – – Scrolls the title once [y] – To resume playback, touch/press again or touch/press / [5]. [d] [s] Fast Forward/ Fast Reverse Title Scroll Pause …… Touch/Press and hold 18 CQ-VD7003N DVD VTR RADIO CH-C END – – To cancel, touch again. English – – To cancel, touch and hold again. 18 Useful Function Shuffle Songs * Shuffle Albums * Note: ¡The shuffle function of iPod corresponds to the RANDOM function of this unit. Repeat Play – To cancel, touch again. – Note: ¡The All Repeat Play function of iPod is always activated and cannot be canceled from this unit. …… Touch/Press and hold Touching * Touch panel symbols will change to indicate these current mode. {A= ALBUM (album), {S= SONG (song)} allows users to switch between screens as follows. Standard Screen File indicator A number up to 999 is displayable. Current state File up/down Operation Screen File indicator A number up to 999 is displayable. Title scroll Play/pause Play setting File up/down Folder List/File List Screen Back to 1-upper directory Playback category selection button Playback by playlist (default) Playback by album Playback by song Playback by artist Folder list/file list CQ-VD7003N 19 English Settings 19 This is a guide book specific to system upgrading. Please refer to the operating instructions for basic operations, menu operations, specifications, etc. USER SCREEN AUDIO DVD INPUT/OUTPUT RADIO CAMERA SETUP Rear View Camera set up NAVI SETUP (Navigation set up) CAMERA Navigation Setting NAVI SP Selection of the terminal that connects to the rear view camera. (Navigation Speaker) Preparation: Connect the reverse lead. (a Installation Instructions) : Front Left/Right speaker BOTH L ch : Front Left only R ch : Front Right only default: NAVI MUTE : – 20 dB LEV 2 : – 30 dB LEV 3 : no sound : unconnected ON : connected to the CAMERA-IN default: Note: ¡Make sure to select connected. (Navigation mute level) SCALE OFF OFF when no rear view camera is (Rear view camera scale) Images through the rear view camera can be shown in scale display mode. : unchanged LEV 1 OFF BOTH Preparation: Connect the navi mute lead. OFF (Rear view camera set up) OFF : scale display off ON : scale display on default: default: Note: ¡You can set the navigation mute level when selected on NAVI INPUT (navigation input). OFF LEV 1 SCALE ADJUST RGB is (Scale adjustment) ] or [ : adjust INPUT SELECT NAVI VOLUME (Navigation Volume) Volume adjustment of the car navigation system. ] : down, [ : up Setting range: 0 to 40 default: 20 Input selection NAVI INPUT (Navigation Input) RGB : connected to the RGB input cord, or a car navigation system not connected AV1 : connected to the AV1-IN default: CH VIDEO INPUT RGB (Video input for DVD Changer) OFF : unconnected ON : connected to the AV2-IN default: OFF Note: ¡The audio output should be connected to the AV2-IN. 20 CQ-VD7003N English Note: OUTPUT SELECT 20 Output Selection REAR MONITOR (Rear Monitor Set up) You can have different picture and sound on the front and rear monitors at the same time. Preparation: Connect another optional rear monitor. (a Installation Instruction) ❑ When the Expansion Module (CY-EM100N, option) is disconnected: AUTO : same as front monitor DVD : DVD/VCD/CD/MP3/WMA AV1 : AV1 AV2 : AV2 default: ¡The screen above shows the case that no device is connected to the Expansion Module. In such a case, the additional buttons are displayed gray and not selectable. ¡Only single source of audio and video can come out through the Expansion Module (CY-EM100N, option). Therefore, if the audio and video from the changer are played on the front monitor, the audio and video from the TV cannot be played on the rear monitor at the same time. Example: When a DVD changer and a TV are connected to the Expansion Module (CY-EM100N, option), AUTO Note: ¡This menu can also be opened by touching/pressing and holding /[MENU]. ¡Images are not displayed on the rear monitor in the DVD changer mode even if AUTO is selected. ❑ When the Expansion Module (CY-EM100N, option) is connected: is selectable. However, the setting is not ¡ feasible because the changer is in operation on the front monitor. ¡To play the TV on the rear monitor, select for the front monitor, or select a source other than the Expansion Module. H-F SETUP (Hands-free Set Up) Hands-free Set Up H-F SP ¡Connection of the Expansion Module (CY-EM100N, option) provides two additional source buttons. ¡Connection of audio-only source to the Expansion Module (CY-EM100N, option) provides no additional button. (Hands-free speaker) Preparation: Connect Bluetooth hands-free kit (CYBT100N). (a Installation Instructions) BOTH : Front Left/Right speaker L ch : Front Left only R ch : Front Right only default: BOTH CQ-VD7003N 21 English Troubleshooting ❑ If You Suspect Something Wrong Check and take steps as described below. 21 If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service Centre. The product should be serviced only by qualified personnel. Please refer checking and repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking. Never take measures especially those other than indicated by italic letters in “Possible Solution” described below because those are too dangerous for users to handle themselves. Warning ¡Do not use the unit in an irregular condition, for example, without sound, or with smoke or a foul smell, which can cause ignition or electric shock. Immediately stop using the unit and consult your dealer. ¡Never try to repair the unit by yourself because it is dangerous to do so. ■ Car Navigation, VCR, Camcorder, Rear View Camera, Rear Monitor Problem The picture from a car navigation system is not displayed. The connection of a car navigation system is not correct. aConnect it correctly. The picture from a VCR or a camcorder is not displayed. A VCR or Camcorder is not connected correctly. aConnect a VCR or Camcorder correctly. The picture from a rear view camera is not displayed. Rear view camera is not connected correctly. aConnect a rear view camera correctly. The picture or the sound of the rear monitor is not switchable. 22 Possible cause a Possible solution CQ-VD7003N Input setting of a car navigation system is not correct. aCorrect the input setting. Input setting of camera is not correct. aCorrect the input setting. AUTO is not selected as the rear monitor setting. aSelect AUTO for the setting. English ❑ Error Display Messages ■ CD Changer/DVD Changer Control Display NON PLAYABLE DISC MECHANISM ERROR Possible cause a Possible solution Disc has scratches. aCheck disc. No operation by some cause. aPress [u]. If failure persists, press the reset switch. (Press the reset switch in the CD changer). If normal operation is not restored, call the store where you purchased the unit or the nearest Panasonic Service Centre. FILE ERROR The type of the file that is selected is not supported. aCheck disc. PROTECTED A WMA file can be copyrighted. aThe file protected by copyright is not playable. NO DISC NO MAGAZINE REGION ERROR 22 Disc is dirty, or is upside down. aCheck disc. No disc is in the player. aInsert disc into the disc slot. No magazine is in the changer. aLoad the changer with CD-loaded magazine. An attempt was made to play a disc with a region number other than “2” or “ALL”. aPress [u] and check the disc. Note: ¡There may be cases when the disc numbers affected by an error are displayed before “NON PLAYABLE DISC”. ¡Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the Operating Instructions for the changer used. ■ iPod Control NO iPod NO SONGS The iPod cable was disconnected in the iPod mode. aReconnect the iPod cable. Your iPod has no playable music. aDownload playable music to your iPod. CQ-VD7003N 23
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project