Candy CTDF 1306-S, CTDF 1306E-47, CTDF 1306-47 User manual

WASHING MACHINE CTDF 1306
H
V
G
A
B1
C1
A
B2
C2
p
PROGRAMME SELECTOR
Use this control to select the desired wash programme. Turn the selector (it
can be turned in both directions) so that the programme is opposite the
reference indicator (p). The temperature selected will depend on the
programme. (See the Programme Table).
B1
SPIN SPEED SELECTOR
B2
DELAY START
C1
COLD WASH
C2
AQUAPLUS (SENSITIVE KEY)
G
DOOR LIGHT
H
START/PAUSE KEY
V
“DIGITAL” Display
The display’s indicator system allows you to be constantly informed about the status of
the machine
p
CONTROL POSITION INDICATOR
Programme table mod CTDF 1306
programme
COTTONS
MIXED
SYNTHETICS
DELICATES
SPECIAL
programme for
aprox.
time
min.
max.
temp.
setting
ºC
spin
speed
rpm/min
max.
load
Kg.
washing powder option keys
load
C
I
II








6




1300
6




30º
1300
6




display
50º
1000
2




Delicate coloureds
display
40º
1000
2




Delicate coloureds
display
30º
1000
2




Delicates
display
40º
600
1,5



display
30º
800
1



display
30º
800
2



White
display
90º
1300
6
Fast coloureds with prewash
display
60º
1300
6
*Fast coloureds
display
60º
1300
*Fast coloureds
display
40º
Delicate coloureds
display
Fast coloureds
Woollens
Hand wash



Gentle rinse
display
1000
Gentle spin
display
1300
Empty
Mix&wash (M&W)
display
40º
1000
6



Fast 44
display
40º
1000
3



Fast 32
display
30º
1000
2



display

* Cotton wash programme requirements according to (EU) 1015/2010 e nº 1061/2010 regulations
60° Cotton wash programme
40° Cotton wash programme
These wash programmes are recommended for soiled cotton fabrics and are the most effective in terms of both
energy efficiency and water consumption.
These programmes have been designed to comply with the recommended wash temperatures specified on the
labelling: the specified temperature may differ slightly from that indicated on the wash cycle.
Technical data mod.
CTDF 1306
Mains
voltage
220-230V.
50Hz.
Mains fuse
Amp. rating
Water
pressure
Max.
Power input
10 A.
0,05-0,8 Mpa
1500
IMPORTANT: Do not use liquid detergent for programs with a prewash cycle and/or timed start.
PREPARING THE WASH CYCLE
1.- Once the washing is loaded, ensure that the drum doors are properly closed..
2.- Add detergent and additives, not exceeding the maximum level indicator.

detergent for pre-wash I

detergent for wash programme II

fabric conditioner
SELECTING THE DESIRED PROGRAMMES AND OPTIONS
3.- Turn the programme selector (A) to the desired programme.
4.- Press the key or keys for any options desired (C1, C2,).
.- It is advisable to select the required options before pressing the Programme Start key (H).
.- Remember that if the programme has already passed the stage at which an option is activated, that option
will not be implemented.
C1 cold wash key
By pressing this button it is possible to transform every programme into a cold washing one, without
modify other characteristics (water level, times, rythmes, etc..).
Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely washed
thanks to this new device.
C2 aquaplus (sensitive key)
Thanks to the new SENSOR ACTIVA SYSTEM, by pressing the key it is possible to run a special
washing cycle applicable to all programs and types of fabric, caring for their fibres and the delicate skin of
the users who use them.
Taking on much more water, together with the new combined action of drum rotation cycles and taking on
and discharging water allow you to obtain perfectly clean, rinsed clothes. More water is used in the wash
to dissolve the detergent completely, ensuring an effective washing action. The water in the rinses has
also been increased to eliminate all trace of detergent in the fibres.
This function has been specifically studied for people with delicate, sensitive skin, who can suffer irritation
or allergy from the slightest detergent residue.
It is also advisable to use this function for children's clothes and delicate fabrics in general, especially for
washing bathrobes, whose fibres tend to retain detergent.
This option is not available for the wool program.
5- Select spin speed if required (B1)
B1 spin speed
Once the programme has been selected, the maximum spin speed allowed for that programme appears
on the display. Pressing the spin button will reduce the speed by 100 rpm each time the button is
pressed. The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the spin
button repeatedly.
6.-To start the programme, once options have been chosen, press the key H. The washing machine will
begin to operate. If you wish to cancel the option you have selected, press the key again. (The pilot light
will go off).
B2 delay start button
This button allows you to pre-programme the wash cycle to delay the start of the cycle for up to 24 hours.
To delay the start use the following procedure:
Set the required programme.
Press the button once to activate it (h00 appears on the display) and then press it again to set a 1 hour
delay (h01 appears on the display); the pre-set delay increases by 1 hour each time the button is
pressed, until h24 appears on the display, at which point pressing the button again will reset the delay
start to zero.
Confirm by pressing the “START/PAUSE” button (the light on the display starts to flash). The countdown
will begin and when it has finished the programme will start automatically.
It is possible to cancel the delay start by taking the following action:
Press and hold the button for 5 seconds until the display will show the settings for the programme
selected.
At this stage it is possible to start the programme previously selected by pressing the “START/PAUSE”
button or to cancel the process by setting the selector to the OFF position and then selecting another
programme.
cycle duration (V)
When a programme is selected the display automatically shows the cycle duration, which can vary,
depending on the options selected.
Once the programme has started you will be kept informed constantly of the time remaining to the end of
the wash.
door light (G)
Once the START/PAUSE button has been pressed the light first flashes then stops flashing and remains
on until the end of the wash.
2 minutes after the end of the wash the light goes off to show that the door can now be opened.
Cancel-change programs
Once you have started a program, and wish to change or cancel it, you should proceed in the following
manner,
- Put the program selector in the OFF position. At that instant, you have cancelled the program and can
if you wish to do so, select a new one.
- Select the new program.
- Click the key (H) again.
The washing machine will perform the new selected program.
Programme pause
It is possible to momentarily stop the wash programme so that more washing can be added, and to do so,
proceed as follows:
- Hold down the (H) key until the option key lamps begin to flash and the time remaining indicator
display, and pilot lamp lights up.
- When the Door Lock lamp goes out (after approx. 2 minutes), open the door and add the desired
washing.
- Correctly close the doors of the drum and the outer cover.
- Press the key H, and the washing machine will continue with the programme.
When the programme has been completed, the message "END" will appear in the indicator display,
Wait until the Door Lock lamp (G) goes out (after approx. 2 minutes)
“To remove the washing, set the programme selector to the OFF position”, before opening the
washing-machine lid and the drum doors.
10.04.12/ H-46006513 EN