advertisement
▼
Scroll to page 2
OWNER’S MANUAL OM-1077 144054G 2018−12 Wire Feeder Cart (142382) For 20, 22A, 24A, 50, S-60, S-70, And D-60 Series Feeders 1. Safety Symbol Definitions DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. DANGER ! - Indique une situation dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves. Les éventuels risques sont représentés par les symboles joints ou expliqués dans le texte. Beware of electric shock from wiring. Disconnect input power before installing this kit. Reinstall all panels and covers. Attention aux décharges électriques au contact des câbles. Couper l’alimentation électrique avant d’installer ce kit. Réinstaller tous les panneaux et couvercles. Fsafe7 2013-10 Fsafe1 2013-10 Indicates a hazardous situation which, if not avoided, could result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. Indique une situation dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves. Les éventuels risques sont représentés par les symboles joints ou expliqués dans le texte. Wear safety glasses with side shields. Porter des lunettes de sécurité avec écrans latéraux. Fsafe8 2013-10 Fsafe2 2013-10 NOTICE Indicates statements not related to personal injury. CALIFORNIA PROPOSITION 65 WARNINGS Signale des consignes non associées aux dommages corporels. Indicates special instructions. WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov Fournit des instructions spéciales. Fsafe3 2013-10 PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov. Fsafe26 2018-01 © 2018 MILLER Electric Mfg. LLC . For S-60, S-70 and 20 series feeders, install stand-offs (4) in holes labeled A, and secure Item No. with four 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3). For D-60 series, install stand-offs (4) in holes labeled B, and secure with four 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3). 1 1 2 3 For S-22A, install stand-offs (4), in holes labeled C, and secure with three 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3). For 22A, 24A feeders, install stand-offs (4), in holes labeled D, and secure with three 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3). For 50 series, line up holes in feeder base with holes in cart labeled A, and secure with four 10-24 x 2 in. screws (1), washers (2), 3/16 in. flat washers (3), and 10-24 in. nuts (4). Top View Of Cart Base A C B A C D B A C D B D A B 1 2 Part No. Description (Qty) 4 602101 112277 602203 602238 601861 146296 4 601861 Screw, 10-24 x 5/8 (4) Screw, 10-24 x 2 (4) Washer, No. 10 lock (4) Washer, 3/16 flat (4) Nut, 10-24 (4) Stand-Off, No. 10-24 x 1-9/16 (4) Nut, 10-24 (4) 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 604126 602247 097455 121614 603995 601879 602216 255489 135390 601959 604538 602211 604537 123557 124115 144020 144018 Screw, 1/2-13 x 1 (2) Washer, 1/2 flat (6) Wheel, 8 in (2) Retaining Ring (2) Washer, 3/4 flat (2) Nut, 1/2-13 (2) Washer, 1/2 lock (4) Axle Mounting Bracket (2) Axle (1) Screw, 5/16 x 1-1/2 (4) Washer, 5/16 flat (8) Washer, 5/16 lock (4) Nut, 5/16-18 (4) Caster, 5 in (2) Nut, 7/16-14 (2) Base (1) Handle (1) Be sure to provide Model when ordering replacement parts. 3 4 5 11 6 15 21 20 13 7 19 11 6 14 15 16 17 Tools Needed: 12 . Remove paint from axle 6 3 2 8 10 1 grooves (13) before installing retaining rings (8). 9 18 5/16, 1/2, 9/16, 3/4 in. Ref. 144021 / 145362 OM-1077 Page 2
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement