Miller WIRE FEEDER CART (142382) Owner's Manual

OWNER’S MANUAL

OM-1077

2019

−

11

Wire Feeder Cart (142382) For 20, 22A, 24A, 50, S-60, S-70, And D-60 Series Feeders

144054H

1.

Safety Symbol Definitions

DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text.

DANGER ! - Indique une situation dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves. Les éventuels risques sont représentés par les symboles joints ou expliqués dans le texte.

Fsafe1 2013-10

Indicates a hazardous situation which, if not avoided, could result in death or serious injury . The possible hazards are shown in the adjoining symbols or explained in the text.

Indique une situation dangereuse qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves. Les

éventuels risques sont représentés par les symboles joints ou expliqués dans le texte.

Fsafe2 2013-10

NOTICE Indicates statements not related to personal injury.

Signale des consignes non associées aux dommages corporels.

Indicates special instructions.

Fournit des instructions spéciales.

Fsafe3 2013-10

Beware of electric shock from wiring. Disconnect input power before installing this kit. Reinstall all panels and covers.

Attention aux décharges électriques au contact des câbles. Couper l’alimentation électrique avant d’installer ce kit. Réinstaller tous les panneaux et couvercles.

Fsafe7 2013-10

Wear safety glasses with side shields.

Porter des lunettes de sécurité avec écrans latéraux.

Fsafe8 2013-10

CALIFORNIA PROPOSITION 65 WARNINGS

WARNING: Cancer and Reproductive Harm − www.P65Warnings.ca.gov

PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS

AVERTISSEMENT : cancer et troubles de la reproduction − www.P65Warnings.ca.gov.

Fsafe26 2018-01

©

2019 MILLER Electric Mfg. LLC

.

For S-60, S-70 series feeders, install stand-offs (4) in holes labeled A, and secure with four

10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3).

For D-60 series, install stand-offs (4) in holes labeled B, and secure with four 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3).

For 20 series feeders, install stand-offs (4), in holes labeled C, and secure with four 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3).

For S-22A, install stand-offs (4), in holes labeled D, and secure with three 10-24 x 5/8 in.

screws (1), washers (2), and 3/16 in. flat washers (3).

For 22A, 24A feeders, install stand-offs (4), in holes labeled E, and secure with three 10-24 x 5/8 in. screws (1), washers (2), and 3/16 in. flat washers (3).

For 50 series, line up holes in feeder base with holes in cart labeled A, and secure with four 10-24 x 2 in. screws (1), washers (2), 3/16 in. flat washers (3), and 10-24 in. nuts (4).

Top View Of Cart Base

A C B A C

D

E

D E

B

A C B A

D

C

E

B

Description (Qty)

1 602101 Screw, 10-24 x 5/8 (4)

1 112277 Screw, 10-24 x 2 (4)

2 602203 Washer, No. 10 lock (4)

3 602238 Washer, 3/16 flat (4)

601861 Nut, 10-24 (4)

4 146296 Stand-Off, No. 10-24 x

1-9/16 (4)

4 601861 Nut, 10-24 (4)

5 604126 Screw, 1/2-13 x 1 (2)

6 602247 Washer, 1/2 flat (6)

7 097455 Wheel, 8 in (2)

8 121614 Retaining Ring (2)

9 603995 Washer, 3/4 flat (2)

10 601879 Nut, 1/2-13 (2)

11 602216 Washer, 1/2 lock (4)

12 255489 Axle Mounting Bracket (2)

13 135390 Axle (1)

14 601959 Screw, 5/16 x 1-1/2 (4)

15 604538 Washer, 5/16 flat (8)

16 602211 Washer, 5/16 lock (4)

17 604537 Nut, 5/16-18 (4)

18 123557 Caster, 5 in (2)

19 124115 Nut, 7/16-14 (2)

20 144020 Base (1)

21 144018 Handle (1)

Be sure to provide Model when ordering replacement parts.

1

2

3

4

21

15

20

19

11

6

Tools Needed:

15

16

17

14

3

2

1

18

5/16, 1/2, 9/16, 3/4 in.

13

12

6

10

9

5

11

6

8

7

.

Remove paint from axle grooves (13) before installing retaining rings (8).

Ref. 144021 / 145362

OM-1077 Page 2