Shure MXCIC Microflex Complete Interpreter Console () User guide

MXCIC
Microflex Complete Interpreter Console (MXCIC)
Version: 6 (2019-H)
Shure Incorporated
Table of Contents
Normal Operation
10
Selection of Incoming Languages
10
Showing Quality of Incoming Language
11
Selection of Outgoing Channels
11
Language Interpretation
11
Wireless Language Distribution
12
Tech Menu
12
Error Indication
13
Power and Configuration Requirements
13
Specifications
14
Language List
17
Important Product Information
20
MXCICMicroflex Complete Interpreter Console (MXCIC) 3
Safety Information
3
IMPORTANT SAFETY INSTRUCTIONS
3
SAFETY PRECAUTIONS
4
WARNING
4
Description
Features
Hardware
Connections
Interpreter Navigation and Menu Screens
4
5
5
7
7
Back/Cancel
8
Settings
8
Agenda
8
Messages
8
Speak List
9
Home
9
Warning:
21
9
Compliance
22
Certifications
22
Interpretation Setup
Interpretation Channels
10
Language Setup
10
Booth Channel Setup
10
Information to the user
21
2/22
Shure Incorporated
MXCIC
Microflex Complete Interpreter Console (MXCIC)
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4.
5.
6.
7.
8.
9.
10.
11.
12.
FOLLOW all instructions.
DO NOT use this apparatus near water.
CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance
with the manufacturer’s instructions.
DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (in­
cluding amplifiers) that produce heat. Do not place any open flame sources on the product.
DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace­
ment of the obsolete outlet.
PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
ONLY USE attachments/accessories specified by the manufacturer.
USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the
apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connec­
tion.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.
21. Operate this product within its specified operating temperature range.
3/22
Shure Incorporated
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in the literature accom­
panying this unit.
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified
service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting.
SAFETY PRECAUTIONS
The possible results of incorrect use are marked by one of the two symbols—"WARNING" and "CAUTION"—depending on the
imminence of the danger and the severity of the damage.
WARNING: Ignoring these warnings may cause severe injury or death as a result of incorrect operation.
CAUTION: Ignoring these cautions may cause moderate injury or property damage as a result of incor­
rect operation.
WARNING
LISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOL­
UME AS POSSIBLE. Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced
hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA)
on maximum time exposure to sound pressure levels before hearing damage occurs.
90 dB SPL
95 dB SPL
100 dB SPL
105 dB SPL
at 8 hours
at 4 hours
at 2 hours
at 1 hour
110 dB SPL
115 dB SPL
120 dB SPL
at ½ hour
at 15 minutes
Avoid or damage may occur
Note: Use this product only with an agency approved power supply which meets local regulatory requirements (e.g., UL, CSA, VDE, CCC, INMETRO).
1. 經審驗合格之射頻電信終端設備，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。
2. 射頻電信終端設備之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得
繼續使用。所謂合法通信，係指依電信法規定作業之無線電信。
3. 輸入、製造射頻電信終端設備之公司、商號或其使用者違反本辦法規定，擅自使用或變更無線電頻率、電功率者，除依電
信法規定處罰外，國家通訊傳播委員會並得撤銷其審驗合格證明。
4. 減少電磁波影響，請妥適使用
Description
®
The MXCIC provides comprehensive facilities for professional interpretation in the Microflex Complete Conference System. It
is a portable, multi-channel console for simultaneous interpretation during a conference. Up to 31 interpretation channels can
be used simultaneously by connecting multiple MXCIC consoles.
The console provides consistent, high­quality audio performance, irrespective of the individual interpreter’s speech level. The
digital design virtually eliminates background noise, distortion and crosstalk. Participants simply select the channel from their
conference unit and use headphones to monitor the conference in their language.
4/22
Shure Incorporated
The MXCIC connects to any unit in the DCS-LAN chain, transporting power, audio, and control data over a single Cat5e cable.
Translation channels are carried alongside the floor channel and are accessible at any conference unit with a channel selector.
The integrated loudspeaker allows the interpreter to listen to the floor during operation.
A large backlit display is provided for easy identification of the language used to monitor, and the outgoing languages from the
interpreter. The relay level of each pre-selected language is shown, indicating if the monitored language is original from the
talker, a direct interpretation, or an interpretation with two relays.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fully digital audio transmission
DCS-LAN connection with built-in data refresh and cable redundancy
Up to 150 interpreter consoles per system
Support for up to 31 interpretation channels
Three outgoing channels
Eight incoming language channels + floor audio
Support for multiple interlocking modes
Audible cues for visually-impaired interpreters
Independent volume and tone controls
"Slow" button
Light indication in buttons
Lockable gooseneck microphone input
Dedicated "mute" button
Integrated loudspeaker
Multiple jacks for headphones, headsets, or external headphone interfaces
Remotely controllable from the SW6000 Conference Management Software
ISO 20109 compliant
5/22
Shure Incorporated
Hardware
① Loudspeaker Volume
Controls loudspeaker output level
② EQ
Treble/Bass control for headphone audio
③ Volume Knob
Controls the headphone output level
④ Audible Cues
Toggles headphone audible cues for visually-impaired interpreters
⑤ Floor Audio
Selects floor as headphone audio source
⑥ Microphone
Turns microphone on/off
⑦ Mute
Momentary button mutes microphone audio
⑧ Slow
Sends a message to SW6000 that the speaker is talking too fast
⑨ Outgoing Channel Selectors
Determines outgoing channel for audio
◦ A: Primary (booth) language
6/22
Shure Incorporated
◦ B: Secondary interpreter language
◦ C: Tertiary interpreter language
⑩ Navigation
⑪ Selector Knob
Rotate to highlight menu options, push to select
⑫ Incoming Channel Selectors
Programmable buttons for direct selection of incoming audio (relay) channels
⑬ Display
Backlit LCD screen
⑭ Headphone/Headset Jack
TRRS jack for interpreter listening
⑮ NFC Slot
Slot for utilizing NFC-card features (for future use)
⑯ USB Port
Alternate method of loading preferences (for future use)
⑰ Audio Jack
TRS output to external headphone interface
⑱ DCS-LAN Ports
In/out ports for connecting Cat5E shielded cables
⑲ Microphone Connector
Lockable connector for Shure MXC gooseneck microphone
⑳ Integrated Loudspeaker
For audio playback (automatically mutes when any booth microphone is activated)
Connections
Microphone connector
Allows a Shure Microflex gooseneck microphone to connect to the unit.
TRS/TRRS connectors
A mini jack is located on each side of the interpreter unit for connecting a headset or headphones (connecting a headset
will automatically disconnect the audio from a connected gooseneck microphone). A single mini jack is also located on the
bottom of the unit, for connecting to an external headphone interface.
DCS-LAN connector
Two RJ45 sockets are located at the bottom of the console for connecting to the DIS-CCU and other units in the DCS-LAN
network.
Interpreter Navigation and Menu Screens
Use the dedicated buttons to the left of the display to navigate the menus on the MXCIC. Where applicable, rotate the selector
knob to highlight the desired function and press to select the highlighted option.
7/22
Shure Incorporated
Back/Cancel
Returns to the previous step or menu screen.
Settings
From the Settings menu, interpreters can interact with the following options:
• Brightness: Adjust the backlight on the LCD display
• Headphone Sensitivity: Adjust the overall volume range to account for differences in individual headphones
For safety reasons, sensitivity defaults to Low
Agenda
This button is reserved for future use.
Messages
This buttons are reserved for future use.
8/22
Shure Incorporated
Speak List
View the Speak, Request, and Reply lists.
Note: Interpreter units are always active and do not impact the speaker list.
The Speak list settings can be modified through the DIS-CCU web interface.
Home
The Home screen contains the following interface elements:
① Basic Information
Identifies the current screen.
② Incoming Channel Selector
Indicators
Displays the channel number, language, and interpretation quality (see below) of select­
ed relay channels
③ Outgoing Channel Selector
Indicators
Displays the channel number and language for outgoing audio channels
④ Loudspeaker Channel Indi­
cator
Shows the channel the integrated loudspeaker is set to
⑤ Notifications
Indicates incoming messages, hardware connections, etc.
9/22
Shure Incorporated
Interpretation Setup
Multi-language interpretation can be set up through the DIS-CCU web interface in standalone systems, or in SW6000. If more
than 4 languages are needed, purchase and install an additional feature license before setting up interpretation.
Interpretation Channels
Assign the number of interpretation channels needed (0 to 31) at Interpretation > Interpretation channels.
Note: When 0 is selected, only Floor audio (Channel 0) is available.
The Channel display setting determines whether the channel selectors on participant conference units display channel number
or language abbreviation.
Language Setup
The Language setup list shows the channels defined in the Interpreter channels settings. Assign a language from the dropdown menu for each language.
Booth Channel Setup
To simplify managing multiple languages, interpreter consoles are grouped into Booths.
By default, Booth 1 is assigned to Channel 1, Booth 2 to Channel 2 etc., but languages can be manually assigned to booths at
Interpretation > Booth channel setup. Multiple booths can be assigned to the same interpretation channel.
Normal Operation
• Incoming Channel Selector Assignment
To display available channel sources, press and hold an incoming channel selector button (below the screen). Rotate the
selector to highlight the desired language source, and confirm the selection by releasing the selector. This workflow also
applies to outgoing channels B and C, if permission is granted by the system administrator.
Note: Interpreters can only select from languages programmed into the system from the DIS-CCU or SW6000.
• Volume Control
Headphone and loudspeaker volume controls are adjusted using their respective volume knobs. Headphone sensitivity
can be adjusted in the Settings menu.
Note: A double-beep in the headphones indicates the volume has exceeded safe levels for over a minute. Reduce headphone volume to safe listening
levels to dismiss this audible warning.
Selection of Incoming Languages
When interpreting, the interpreter will listen to either the floor audio, or to one of the other interpreted language channels. The
Floor button will select the floor language, and the relay buttons select the predetermined languages, as shown on the display.
The two first characters in the display show the channel number and the following three characters show the corresponding
language in short (see language list). When the Floor button is pressed, the Floor channel is selected and the Floor LED is lit.
When one of the relay channels is selected, the Floor LED goes out, the relay button indicator is lit, and the incoming audio
from the selected channel replaces the floor audio.
10/22
Shure Incorporated
Only the number of channels set at the Channel Set-up menu at the DIS-CCU can be selected and shown.
A complete list of supported languages is available at the end of this manual.
Showing Quality of Incoming Language
To the right of the relay language display, the quality of the source interpretation is indicated:
•
•
•
•
O : Floor audio (no interpretation)
+ : Direct interpretation of floor audio
- : Single relay interpretation
= : Two or more relays
Actual quality of interpretation channels is displayed at all times.
An S (Self) is shown as the quality indication when an incoming channel is set to the same language as an active outgoing channel on the unit.
Selection of Outgoing Channels
The A, B and C buttons select the outgoing channel. Pressing a button overrides the previously-selected outgoing channel. The
A channel is configured in the system settings as the primary language for that interpretation booth; B and C channels can be
selected as secondary interpretation languages.
The highlight and icon on the display screen next to each button shows the status of the respective interpretation channel.
• Yellow indicates that the corresponding outgoing channel is occupied.
• Red highlight indicates that the microphone in the interpreter console is active on the selected channel.
• Blue indicates that the channel is selected and there is no interpretation activity on the channel.
Note: If the status is changed temporarily, such as the microphone on an active channel being muted, the icon will reflect the temporary state while the high­
light color indicates the normal behavior.
Language Interpretation
Up to 31 channels are available for simultaneous interpretation of the meeting. The MXCIC interpretation unit connects to the
DCS­LAN network from the DIS­CCU, transmitting audio to independent language channels. Participants listen to their lan­
guage on headphones connected to their respective conference unit. See the MXCIC User Guide for more information.
Four languages are provided with the FL6000 mode license, and can be expanded to 8, 16, or 31 with an additional license.
11/22
Shure Incorporated
Wireless Language Distribution
Provide additional monitoring access by connecting a wireless language distribution system to the one of the DIS-CCU audio
outputs. Use the browser interface to route the desired interpretation channels or a subset of microphones to that group output.
The DIR Digital Infrared Language System transmits this audio signal to a number of portable listening devices.
Wireless Language Distribution
12/22
Shure Incorporated
Tech Menu
The unit settings in the Tech Menu can be accessed by pressing the second incoming channel selector and the B outgoing
channel selector at the same time.
This menu should only be accessed by a technician or administrator, and access can be blocked from the DIS-CCU if desired.
The Unit menu is accessible from this screen.
• Booth Number: Determines which booth the console is assigned to
• Desk Number: Determines which desk the console is assigned to
• Out B/C Language: Option to make the following selections:
◦ Not allowed
◦ Select from one
◦ Select from all
If Select from one is chosen, that language has to be selected first for the outgoing channel
•
•
•
•
Floor Toggle: Floor button can be set to toggle between floor audio and last selected relay channel
Out A/B/C Switch: Choose if interpreters can switch between outgoing channels while the microphone is active
Unit Stats: Displays the error log and gives option to reset
Unit Info: Displays version, serial number and IP address
Error Indication
Communication errors between the MXCIC and DIS-CCU are indicated in the MXCIC. The first error threshold is reached when
audio data from the DIS-CCU contains too many errors for the sound to be reproduced correctly, which is indicated by a black
matrix in the normal operation display, and by the communication display when the set is uninitialised.
The second threshold is reached when the frame error rate reaches a predefined upper value. When this happens, the unit will
enter the communication status display regardless of the state the console was in before errors occurred.
The error status is checked every 5 seconds. If no errors have occurred since the last check, the MXCIC enters the operation
mode it was in before errors were detected.
13/22
Shure Incorporated
Power and Configuration Requirements
Connect the IN socket on the MXCIC to the OUT port on the previous unit or DIS-CCU using Cat5e FTP or STP cables, and
the OUT port on MXCIC to the IN on the next unit in the network.
For cable length and power requirements, please refer to the MXC Power Calculator, available at https://dcslan.shure.com.
Specifications
Latency
Microphone Input to Headphone Output
5.5ms
Microphone Input to Analog out
6.25ms
Analog in to Headphone Output
7.25ms
Audio Frequency Response
Loudspeaker Output
200 Hz - 16 kHz (+0.5/-10 dB)
Headphone Output
110 Hz - 16 kHz (+0.5/-3 dB)
THD+N
0.2%
Digital Signal Processing
24-bit, 32 kHz
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 (DIS-CCU Out­
put)
Mean Time Between Failures
>400,000 hours
Microphone Connector
10-pin gooseneck
Pin Assignments
Proprietary Shure Pinout
Input Connector
Unbalanced
Output Connector
dual mono (will drive stereo phones)
Network Connections
DCS-LAN
14/22
Shure Incorporated
Power Supply
DCS-LAN (DIS-CCU, EX6010, PI6000)
Voltage At Source
20 to 48 V
Cable Requirements
Cat 5e or higher
NFC Carrier Frequency
13.56 MHz
Antenna Type
Internal NFC Loop
NFC Card Compatibility
ACOS3 dual interface and contactless
Color
Black
Housing
Molded Plastic, Aluminum
Operating Temperature Range
−6.7℃ (20℉) - 40℃ (104℉)
Storage Temperature Range
−29℃ (−20℉) - 74℃ (165℉)
Relative Humidity
95%
Audio Output Type
3.5mm female socket (x2, dual mono, TRRS) 6.35mm female socket (x1, stereo, TRS)
Dimensions
198 x 324 x 96 mm (7.8 x 12.8 x 3.8 in.) H x W x D
Weight
2250 g (79.4 oz.)
Screen Type
Color TFT Display
Screen Size
160 mm (6.3 in.)
15/22
Shure Incorporated
Display Resolution
800 x 240 (134 PPI)
Power Consumption
Typical
5.5 W
Maximum
7.0W
Number of Incoming Channels
Up to 32 (31 + Floor)
Number of Outgoing Channels
3 (A/B)
Maximum Units Per Booth
32
Maximum Number of Booths
150
Maximum Number of Units (total)
128
Audio Input
Nominal Input Level
−60 dBV
Maximum Audio Input Level
Microphone
−1.5 dBV at 1% THD
Headset
−5.5 dBV at 1% THD
Audio Frequency Response
20 Hz - 16 kHz (+0.5/-10 dB)
THD+N
Microphone Input
0.04%
Headset Input
0.07%
Dynamic Range
Microphone Input , Unweighted
110 dB
Microphone Input , A-Weighted
112 dB
Headset Input , Unweighted
92 dB
Headset Input , A-Weighted
94 dB
16/22
Shure Incorporated
Preamplifier Equivalent Input Noise (EIN)
−115.8 dBV
Input Impedance
Microphone
26 kΩ
Headset
2.2 kΩ
Audio Output
Nominal Output Level
70 dB SPL at 0.5m
Maximum Audio Output Level
Loudspeaker Output
82 dB SPL­A at 0.5m
Headphone Output
1.7 dBV
Audio Frequency Response
Speaker Output
200 Hz - 16 kHz (+0.5/-10 dB)
Headphone Output
110 Hz - 16 kHz (+0.5/-3 dB)
THD+N
Loudspeaker Output
<1%
Headphone Output
<0.2%
Dynamic Range
Speaker Output , Unweighted
92 dB
Speaker Output , A-Weighted
MXCIC = 95 dB
Headphone Output , Unweighted
MXCIC = 91 dB
Headphone Output , A-Weighted
MXCIC = 93 dB
Load Impedance
>8 Ω
Language List
Language
ISO 639-2/B-abbreviation
Floor language
FLO
Afrikaans
AFR
Albanian
ALB
Arabic
ARA
17/22
Shure Incorporated
Armenian
ARM
Azerbaijani
AZE
Basque
BAQ
Belarusian
BEL
Bengali
BEN
Bulgarian
BUL
Burmese
BUR
Cantonese
CAN
Catalan
CAT
Chinese
CHI
Corsican
COR
Croatian
SCR
Czech
CZE
Danish
DAN
Dutch
DUT
English
ENG
Estonian
EST
Finnish
FIN
French
FRE
Gallegan
GLG
Georgian
GEO
German
GER
Greek
GRE
Hausa
HAU
Hebrew
HEB
Hindi
HIN
Hungarian
HUN
Icelandic
ICE
Indonesian
IND
Irish
GLE
18/22
Shure Incorporated
Italian
ITA
Japanese
JAP
Javanese
JAV
Kazakh
KAZ
Khmer
KHA
Kirghiz
KIR
Korean
KOR
Kurdish
KUR
Lao
LAO
Latvian
LAV
Lithuanian
LIT
Macedonian
MAC
Malay
MAY
Maltese
MAL
Marathi
MAR
Mongolian
MON
Nepali
NEP
Norwegian
NOR
Panjabi
PAN
Persian
PER
Polish
POL
Portuguese
POR
Raetoroman
ROH
Romanian
RUM
Russian
RUS
Serbian
SCC
Sinhalese
SIN
Slovak
SLO
Slovenian
SLV
Spanish
SPA
19/22
Shure Incorporated
Swahili
SWA
Swedish
SWE
Tagalog
TGL
Tajik
TGK
Tamil
TAM
Telugu
TEL
Thai
THA
Tibetan
TIB
Turkish
TUR
Turkmen
TUK
Ukrainian
UKR
Urdu
URD
Uzbek
UZB
Vietnamese
VIE
Welsh
WEL
Yoruba
YOR
Other no 1
N1
Other no 2
N2
Other no 3
N3
Other no 4
N4
Other no 5
N5
Other no 6
N6
Other no 7
N7
Other no 8
N8
Other no 9
N9
Other no 10
N10
Other no 11
N11
Other no 12
N12
20/22
Shure Incorporated
Important Product Information
The equipment is intended to be used in professional audio applications.
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.
Note: This device is not intended to be connected directly to a public internet network.
EMC conformance to Environment E2: Commercial and Light Industrial. Testing is based on the use of supplied and recommended cable types. The use of
other than shielded (screened) cable types may degrade EMC performance.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Information to the user
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip­
ment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol­
lowing measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
This device contains licence­exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Develop­
ment Canada’s licence­exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Warning:
Operation is subject to the following conditions: (1) The device may not cause harmful interference, and (2) the device must ac­
cept any interference received, including interference that may cause undesired operation.
21/22
Shure Incorporated
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
residential, commercial or light industrial environments. The equipment generates, uses, and can radiate radio frequency ener­
gy and if not installed and used in accordance with the user manual it may cause harmful interference to radio communica­
tions.
Operation of this equipment in residential areas is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense. Intentional or unintentional changes or modifications not expressly ap­
proved by the party responsible for compliance shall not be made. Any such changes or modifications could void the user’s au­
thority to operate the equipment.
If necessary, the user should consult a dealer or an experienced radio/ television technician for corrective action. The user may
find the following booklet prepared by the Federal Communications Commission helpful: "How to identify and Resolve RadioTV Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock
No. 004-000-00345-4.
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Compliance
This equipment has been tested and found to comply with the limits of the following for a Class A digital device:
•
•
•
•
•
•
EN55103-1 (Emission)
EN55103-2 (Immunity)
FCC rules part 15, class A (Emission)
ICES-003 of Industry Canada
IEC 60065
ISO 20109
Certifications
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: [email protected]
22/22
">