Zebra QLn User Guide
Zebra QLn is a mobile printer series designed for businesses that need to print labels, receipts, and other documents on the go. It has a rugged exterior which is important for the longevity of the device. Thanks to its durable construction and compact size, the printer is a good fit for harsh environments and transportation logistics. It also features wireless connectivity options, a long-lasting battery, and a user-friendly interface, making it ideal for a variety of applications, including retail, healthcare, transportation, and more.
Advertisement
Advertisement
QLn Series
TM
Mobile Printers
User Guide
P1028026-005 Rev. A
1
QLn Series User Guide
Table of Contents
Introduction to the QLn™ Series Printers........................................................8
Model UCLI72-4 Quad Charger (AC18177-5).....................................................19
AC Power Adapter (p/n P1031365-024).............................................................21
Loading Media in Peel-off Mode (QLn220/320)...............................................29
Loading Media in Peel-off Mode (QLn420)......................................................30
Home Menu Screen (QLn420 and QLn Healthcare Printers)..........................40
Providing Strain Relief for Communications Cable.........................................47
2
QLn Series User Guide
Wireless Communications with Bluetooth.....................................................49
Memory and Communications Specifications ...............................................71
CPCL Font and Bar Code Specifications and Commands.............................73
ZPL Font and Bar Code Specifications and Commands................................74
Physical, Environmental and Electrical Specifications..................................76
Appendix E.......................................................................................................104
3
QLn Series User Guide
4
QLn Series User Guide
Proprietary Statements
This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.
Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all specifications and signs are subject to change without notice.
Agency Approvals and Regulatory Information
Design Safety certified by TUV
EN60950-1: 2nd Ed. Safety Standard
NOM (Mexico)
FCC part 15 Class B
Canadian STD RSS-210
EN55022 Class B European Electromagnetic
Radiation Standard
EN55024: European Immunity Standard
RCM (Australia/NZ)
RoHS II
Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.
No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental damages, the above limitation may not apply to you.
Copyrights
The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL er ® Circuit; E3 ®
® , ZPL II ® , and ZebraLink tm programs; Element Energy Equaliz-
; and AGFA fonts. Software © ZIH Corp. All rights reserved worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype ® , Intellifont ® and UFST ® are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.
Andy TM
Kai TM
, CG Palacio TM , CG Century Schoolbook TM , CG Triumvirate TM
, Monotype Mincho TM and Monotype Sung TM and may be registered in some jurisdictions.
HY Gothic Hangul TM
, CG Times TM , Monotype
are trademarks of Monotype Imaging, Inc.
Angsana TM
Andale
is a trademark of Hanyang Systems, Inc.
is a trademark of Unity Progress Company (UPC) Limited.
® , Arial ® , Book Antiqua ® , Corsiva ® , Gill Sans ® , Sorts ® and Times New Roman ® are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions.
Century Gothic™, Bookman Old Style TM and Century Schoolbook TM are trademarks of The
Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some jurisdictions.
5
QLn Series User Guide
Univers TM is a trademark of Heidelberger Druckmaschinen AG, which may be registered in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG.
Futura ® is a trademark of Bauer Types SA registered in the United States Patent and Trademark Office and may be registered in some jurisdictions.
TrueType ® is a trademark of Apple Computer, Inc. registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
Bluetooth ® is a registered trademark of the Bluetooth SIG.
© 1996–2009, QNX Software Systems GmbH & Co. KG. All rights reserved. Published under license by QNX Software Systems Co.
All other brand names, product names, or trademarks belong to their respective holders.
© 2015 ZIH Corp.
Certified by:
6
QLn Series User Guide
Document Conventions
The following conventions are used throughout this document to convey certain information:
Cautions, Important, and Note
Caution • Warns you of the potential for electrostatic discharge.
Caution • Warns you of a potential electric shock situation.
Caution • Warns you of a situation where excessive heat could cause a burn
Caution • Advises you that failure to take or avoid a specific action could result in physical harm to you.
Caution • Advises you that failure to take or avoid a specific action could result in physical harm to the hardware.
Important • Advises you of information that is essential to complete a task.
Note • Indicates neutral or positive information that emphasizes or supplements important points of the main text.
7
QLn Series User Guide
Introduction to the QLn™ Series Printers
Thank you for choosing our Zebra ® QLn™ Series Mobile
Printers. You will find these rugged printers will become a productive and efficient addition to your workplace thanks to their innovative design and state of the art features. Zebra
Technologies is the leader in industrial printers with worldclass support for all of your bar code printers, software, and supplies.
This user’s guide gives you the information you will need to operate the QLn420, QLn320, and QLn220 printers, including
QLn Healthcare and Made for iPhone
®
(MFi) printers. MFi printers provide Apple co-processor (MFi) support which allows an
Apple device such as an iPhone or iPad
®
to authenticate and connect over Bluetooth
®
.
These printers use CPCL and ZPL programming languages.
To create and print labels using the CPCL and ZPL languages, refer to the Programming Guide for CPCL and ZPL (p/n
P1012728-008). See Appendix G for instructions on how to access manuals on zebra.com.
QLn Series Software Utilities:
• Zebra Net Bridge™ : printer configuration, fleet management
• Zebra Setup Utility: single printer configuration, quick setup
• Zebra Designer Pro: label design
• Zebra Designer Drivers: Windows ® driver
• OPOS Driver: Windows driver
• Multiplatform SDK
(These utilities can be found on the Zebra website at http://www.zebra.com/us/en/support-downloads.html
.
See Appendix G.)
8
QLn Series User Guide
Unpacking and Inspection
• Check all exterior surfaces for damage.
• Open the media cover (refer to “Loading the Media” in the
Getting Ready to Print section) and inspect the media compartment for damage.
In case shipping is required, save the carton and all packing material.
Reporting Damage
If you discover shipping damage:
• Immediately notify and file a damage report with the shipping company. Zebra Technologies Corporation is not responsible for any damage incurred during shipment of the printer and will not cover the repair of this damage under its warranty policy.
• Keep the carton and all packing material for inspection.
• Notify your authorized Zebra re-seller.
QLn Series Technology
The QLn420, QLn320 and QLn220 use several technologies made popular in other Zebra Mobile Printer product lines, as well as newer technologies.
Smart Battery
The QLn Series battery pack is a high capacity, smart Lithium
Ion battery that contains electronics which allow the printer to monitor its operating parameters. Among these are the number of charge cycles it has undergone and its date of manufacture.
Using these parameters, the printer’s software can monitor the battery’s condition and alert the user when to recharge or remove the battery from service.
Operating Temperature Charging Temperature
-20 0 C to +55 0 C
(-4 o F to 131 o F)
0 0
(32
C to +40 o F to 104
0 o
C
F)
Storage Temperature
-25 0 C to +65 0 C
(-13 o F to 149 o F)
The QLn Series printers will only function properly with genuine Zebra smart battery packs.
9
QLn Series User Guide
The smart battery’s health has three states: GOOD, REPLACE, and POOR. The battery health factor determines whether or not the printer can operate and what is communicated to the user via the display.
# of Charge Cycles
<300
Health
GOOD
REPLACE
Power-up Message
None
“Battery Diminished
Consider Replacing” *
REPLACE
POOR
“Warning-Battery
Is Past Useful Life” *
“Replace Battery
Shutting Down” **
* Warning accompanied by one long beep.
** Warning will flash on and off accompanied by beeping at a rate of once per second. After 30 seconds the printer will shut down.
Note • Power down the printer before removing the battery to minimize the risk of corruption.
Printing Technology
The QLn Series printers use the Direct Thermal method to print human readable text, graphics and barcodes. It incorporates a sophisticated print engine for optimal printing under all operational conditions.
Direct Thermal
Direct thermal printing uses heat to cause a chemical reaction on specially treated media. This reaction creates a dark mark wherever a heated element on the printhead comes in contact with the media. Since the printing elements are arranged very densely at 203 d.p.i. (dots per inch) horizontal and 200 d.p.i. vertical, highly legible characters and graphic elements may be created a row at a time as the media is advanced past the printhead. This technology has the advantage of simplicity, as there is no requirement for consumable supplies such as ink or toner. However, since the media is sensitive to heat, it will gradually loose legibility over long periods of time, especially if exposed to environments with relatively high temperatures.
10
QLn Series User Guide
QR Code
The QR barcode includes human readable text (URL) which links the user to printer information and short videos on topics such as buying supplies, features overview, loading media, printing a configuration report, cleaning instructions, and accessory information. (See Page 13 for each printer’s URL address.)
Made for iPhone (MFi)
QLn printers support communication with Apple devices running iOS 5 or later over a standalone Bluetooth 3.0 radio and the BT3.0 radio included with the 802.11n (dual) radio.
Only printers with the “M” in the ninth digit spot of the part number support this feature, i.e. QNx-xxxxxMxx-xx.
Near Field Communication (NFC)
A passive NFC tag with the Bluetooth printer address will provide instant access to printer-specific information via an NFCenabled smartphone.
11
QLn Series User Guide
QLn Series Overview
Figure 1: QLn320 Shown
13
1
2
14
11
12
4
5
9
3
6
7
8
3
10
1. Platen Roller
2. Black Bar Sensor
3. Media Support Disks
4. Tear Bar
5. Label Presence Sensor
6. Peeler Lever
7. Peeler Bail
8. Latch Release Lever
9. Key Pad
10. Strap Post
11. Status Screen
12. Printhead
13. Media Cover
14. Gap Sensor
15. Belt Clip
16. Battery
17. USB/RS-232 Comm Ports
18. MAC Address Label
19. Docking Contacts
20. DC Input
21.
NFC (Print Touch Icon)
12
QLn Series User Guide
17
15
16
18
19
Note: Scanning the QR code with a smartphone will provide printerspecific information at www.zebra.com/qln220-info and www.zebra.com/qln320-info .
Note: Tapping the Zebra Print Touch TM icon with a Near Field
Communication (NFC) enabled smartphone will provide instant access to printer-specific information. For more information about
NFC and Zebra products, go to http://www.zebra.com/nfc .
Bluetooth pairing applications via NFC is also possible. Please see
Zebra Multi-platform SDK for more information.
21 20
13
QLn Series User Guide
Figure 2: QLn420 Shown
13
1
2
5
7
11
9
4
1. Platen Roller
2. Black Bar Sensor
3. Media Support Disks
4. Tear Bar
5. Label Presence Sensor
6. Peeler Lever
7. Peeler Bail
8. Latch Release Lever
9. Key Pad
10. Strap Post
11. Status Screen
12. Printhead
13. Media Cover
14. Gap Sensor
14
QLn Series User Guide
15. Belt Clip
16. Battery
17. DC Input
18. MAC Address Label
19. Docking Contacts
20. USB/RS-232 Comm Ports
3
14
12
6
8
10
17
15
16
18
19
Note: Scanning the QR code with a smartphone will provide printerspecific information at www.zebra.com/qln420-info.
20
15
QLn Series User Guide
Getting Ready to Print
Battery
Installing the Battery
Important • Batteries are shipped in sleep mode to preserve their maximum capacity while in storage prior to initial use. Plug in the AC adapter (see Pg. 19) or insert the battery into the Smart Charger 2 or
Quad Charger (see Pg. 17) to wake it up before using for the first time.
1. Locate the battery compartment on the bottom of the printer.
2. Swivel the belt clip (if present) to access battery compart-ment.
3. Insert the battery into the printer as shown in Figure 1. (It is not possible to insert the pack in an incorrect orientation.)
4. Rock the battery into the compartment as shown until it locks in place.
When the battery is first installed, the control panel indicators may briefly turn on and then go off which indicates the battery is not fully charged.
Figure 3: Installing the Battery (QLn220 Shown)
Belt Clip
Battery
16
QLn Series User Guide
Battery Safety
Caution • Avoid accidental short circuiting of any battery. Allowing battery terminals to contact conductive material will create a short circuit which could cause burns and other injuries or could start a fire.
Important • Always refer to the Important Safety Information data sheet shipped with each printer and the Technical Bulletin shipped with each battery pack. These documents detail procedures to ensure maximum reliability and safety while using this printer.
Important • Always dispose of used batteries properly. Refer to
Appendix E for more battery recycling information.
Caution • Use of any charger not approved specifically by Zebra for use with its batteries could cause damage to the battery pack or the printer and will void the warranty.
Caution • Do not incinerate, disassemble, short circuit, or expose to temperatures higher than 65 o C (149 o F).
Charger Safety
Do not place any charger in locations where liquids or metallic objects may be dropped into the charging bays.
17
QLn Series User Guide
Smart Charger-2 (SC2) Single Battery Charger (P1031365-063)
The Smart Charger-2 (SC2) is a charging system for use with the 2-cell and 4-cell lithium-ion smart batteries used in the
QLn Series printers.
Charging Status Indicators
The SC2 uses a LED indicator to indicate the charge state in either Green, Yellow, or Amber as detailed below.
DC Power Input
Present
Present
Present
Present
Present
Indicator
Green
Green
Yellow
Amber
Off
Battery Status
Battery not present
Fully charged
Charging
Fault
Present and Battery
Health = POOR
There will also be a battery charging graphic to indicate that this LED is the charging status indicator .
Battery Health Indicator
The SC2 features a tri-color (Yellow/Green/Amber) LED to indicate the health of the battery pack. An evaluation of the battery health begins upon insertion of the battery in the charger and results in the appropriate LED being illuminated as shown below. The LED will remain illuminated as long as input power is applied.
Battery
None or non-smart
Smart battery present
Smart battery present
Smart battery present
Smart battery present
Indicator
Off
Green
Yellow
Flashing yellow
Amber
Health Status
GOOD
CAPACITY DIMINISHED
PAST USEFUL LIFE
UNUSABLE-REPLACE
(discard per Instructions in
Appendix E
Note • For detailed information on the SC2, refer to the
Smart Charger 2 User Guide (p/n P1040985-001).
18
QLn Series User Guide
Figure 2: Smart Charger-2 (SC2)
Smart Battery Charge Status
LED Indicator
Health Status
LED Indicator
Charge Status Icon Health Status Icon
SC2 Dimensions
Height
65.1 mm (2.56 in.)
Width
101.5 mm (4 in.)
Length
120.9 mm (4.75 in.)
Model UCLI72-4 Quad Charger (AC18177-5)
The UCLI72-4 Quad Charger is designed to charge up to four (4)
QLn Series battery packs simultaneously. Batteries must be removed from the printer to be charged in the Quad Charger.
1. Ensure that the charger has been installed properly per the
Quad Charger instruction manual. Ensure that the power indicator on the front panel is on.
2. Plug a battery pack into any one of the four charging bays as shown in Figure 3, noting the orientation of the battery pack.
Slide the battery pack into the charging bay until it stops and then rock the battery pack back until it snaps into place. The amber indicator directly under the battery being charged will turn on if the battery is properly inserted.
19
QLn Series User Guide
The indicators under the battery will allow you to monitor the charging process per the table below:
Amber Green
On Off
On
Off
Flashing
Flashing
On
Off
Battery Status
Charging
80% charged (O.K. to use)
Completely Charged
Fault-Replace
Battery
Important • A fault condition is caused by a problem with the battery.
The charger may indicate a fault because the battery is too hot or cold to charge reliably. Try to charge the battery again when it returns to the room’s ambient temperature. If the amber indicator starts flashing on the second attempt, the battery should be discarded. Always dispose of batteries in a proper manner as described in Appendix F.
Figure 3: Quad Charger
1. Slide Battery Pack into Charger bay.
Power Supply
2. Rock Battery Pack into place.
Amber
Indicator
Green
Indicator
Charger Bay
Power Indicator
Quad Charger Cycle Times :
Battery Status
Battery 80% Charged
Battery Fully Charged
Standard Pack
<2 Hrs.
< 3 Hrs.
Extended Pack
<4 Hrs.
<5 Hrs.
Note • These times are for completely discharged batteries.
20
QLn Series User Guide
Battery packs which are only partially discharged will take less time to reach their charged state. Batteries which have reached
80% of their charge capacity may be used, however, it is recommended that you allow the batteries to reach a full charge to maintain maximum battery life.
The UCLI72-4 Quad Charger has a safety feature which stops charging a battery after six hours regardless of its charge state. If not fully charged, it might be indicative of a battery that needs to be replaced.
Use care when installing the UCLI72-4 Quad Charger so that you do not block the ventilating slots on the top and bottom covers. Ensure that the charger is plugged into a power source which will not accidently be turned off if you will be charging batteries overnight.
AC Power Adapter (p/n P1031365-024)
Figure 4: Charging the Battery Pack with the AC Power Adapter
AC Adapter
DC Input
AC Power Cord
(varies with geographic location)
21
QLn Series User Guide
• Open the protective cover on the printer to expose the DC input charger jack.
• Connect the appropriate AC power cord for your location to the adapter and then plug the power cord into an AC receptacle.
• Plug the barrel plug from the AC adapter into the charger jack on the printer.
• The printer will power up and begin charging. The printer can be left on or turned off at this point. Charging will continue in either state.
Note • Batteries are shipped in sleep mode to preserve their maximum capacity while in storage prior to initial use. Plug in the AC adapter (see
Pg. 19) or insert the battery into the Smart Charger 2 or Quad Charger (see
Pg. 17) to wake it up before using for the first time.
While it’s possible to charge the battery when using the printer, charge times will increase under this condition.
Ethernet and Charging Cradles
The cradle is an expansion base intended for use with the
QLn Series printers. There is a four bay cradle (QLn-EC4) or a single bay option (QLn-EC) for use with the QLn220 and
320, as shown on pages 23 and 24. There is also a single bay
Ethernet and charging option for the QLn420 (QLn420-EC) as shown on page 24.
The QLn-EC/EC4 cradles provide charging power to the docked printer as well as providing a standard 10/100Mb/S
Ethernet port for communication to the printer. The QLn420-
EC also provides charging power to the docked printer, as well as a standard 10/100Mb/T Ethernet port for communication to the printer. All cradles also supply battery charging power to the docked printer and acts as a supplementary power source for a functioning QLn printer.
All QLn Ethernet cradles feature two LED’s to indicate the status of the cradle: Solid green to indicate when power is provided to the input of the cradle; and blinking green to indicate Ethernet activity.
The cradle allows the user to dock the printer easily and remove it with the push of a button. The printer shall remain
22
QLn Series User Guide
operable while docked, i.e. display is viewable, charge LED status is viewable, and printer controls and data entry are available.
The printer will still print while docked and the user shall be able to replace the media as well.
LED Status
Solid Green
Blinking Green
Indication
Power On
Ethernet Activity
Note • Remove the “Docking Cradle Access” label on the bottom of the
QLn320 or QLn220 printers before docking the printer in the cradle.
DOCKING CRADLE ACCESS
Note • Clean the docking contacts with a Zebra cleaning pen to remove any residue left behind by the label.
The QLn420 does not use the above label over the docking contacts, but instead includes a plastic docking contacts cover secured by two screws. Remove the screws to remove the docking contacts cover from the printer and expose the docking contacts (as shown below).
Docking Contacts
Cover
23
QLn Series User Guide
Docking Contacts
Figure 5: Ethernet Cradle (4-Bay for QLn220/320)
Docking Bay
Ethernet
Status Indicator
Release
Button
Power Status
Indicator
Height
66,7 mm (2.62 in.)
Width
579,9 mm (22.83 in.)
Length
150,57 mm (5.93 in.)
Note • The QLn220 and 320 extended battery capacity is not compatible with the QLn-EC and EC4 cradles.
24
QLn Series User Guide
Figure 6: Ethernet Cradle Single Bay (QLn220/320)
Cradle
Release Button
QLn-EC
QLN420-EC
Height
66,7 mm
(2.62 in.)
66,2 mm
(2.60 in.)
Ethernet Status
Indicator
Release Button
Width
171,28 mm
(6.74 in.)
137,7 mm
(5.42 in.)
Length
150,57 mm
(5.93 in.)
219,6 mm
(8.64 in.)
Figure 7: Ethernet Cradle (QLn420)
Release Button
AC Adapter
Ethernet Status
Indicator
Power Status
Indicator
25
QLn Series User Guide
Printer Operation with Cradle
• All QLn Series printers will charge when placed in their supported cradles.
• Only QLn Series printers that have the Ethernet option installed will connect to an Ethernet network. Check the
PCC code on the back of the printer (see Appendix
D for location). Codes of the form QNx-xxxxx0xx-xx do not support Ethernet, and codes of the form QNxxxxxxExxxx or QNx-xxxxxMxx-xx do support Ethernet
(where “x” means don’t care). You can also check the
“Communications” sub-menu on the LCD (see Main
Menu Screen on page 38). After selecting this sub-menu, any communication options not installed will be so indicated.
• When power is applied to the cradle and the printer is docked, the printer charge LED indicates the charge status of the printer (see Figure 18).
• Docking the printer in the cradle will automatically turn the printer on to ensure it is available to be managed remotely.
• When the printer detects input power from the cradle, and the presence of a live Ethernet link, it will automatically reboot and connect to the Ethernet network.
• For printers with an 802.11 radio, this interface will be turned off when the Ethernet link is active. It will turn back on if the Ethernet link is no longer active.
• For printers with a Bluetooth radio, this interface will remain active while the printer is in the cradle.
• The serial and USB ports will remain active while the printer is in the cradle.
• The DC input barrel jack connector (see Figure 7) cannot be used while the printer is in the cradle. The DC barrel jack should be plugged directly into the cradle instead.
Note • The printer provide over voltage protection such that no damage occurs when voltages from 0-36V are applied at the DC Power jack. Upon application of voltage greater than 36V, the DC line fuse will permanently open to reduce fire hazard. The battery is only charged when 12VDC is applied using the Zebra AC adapter.
26
QLn Series User Guide
Loading the Media in the QLn Series Printers
You can operate QLn Series printers in one of two different modes: Tear-Off or Peel-Off. Tear-Off mode allows you to tear off each label (or a strip of labels) after it is printed. In Peel-Off mode, the backing material is peeled away from the label as it is printed. After you remove this label, the next one is printed.
Loading Media Procedure
1. Open the printer (Refer to Figure 7).
• Press the Media Cover Button on the side of the printer as shown in “1” below. The Media Cover will open automatically.
• Rotate the Media Cover back completely as shown in “2”, exposing the media compartment and adjustable media supports.
Figure 8: Opening the Printer
Media Cover
Media
Compartment
Media Supports
(opposite support not visible)
Latch Release
Lever
27
QLn Series User Guide
2. Pull the media supports apart as shown in Figure below. Insert the roll of media (in the orientation shown) between the supports and let the supports secure the media in place. The supports will adjust themselves to the width of the media, and the media roll should be able to spin freely on the supports.
Figure 9: Loading Media
3. If you plan to use the printer in tear-off mode, close the media coveras shown below.
4
Pull Media out of
Printer
Close Media Cover
Note • Please refer to the Programming Guide (P1012728-xxx) for information on changing the setting to adjust the media feed length via a
Set-Get-Do (SGD).
28
QLn Series User Guide
Loading Media in Peel-off Mode (QLn220/320)
• If you plan to use the printer in the peel-off mode, peel a few labels off of the media and load the media as previously described.
• Push the peeler lever forward to release the peeler bail into the “up” position as shown at “3” and “4” in Figure 10.
• Close the media cover to lock the peeler bail in place. The media will feed between the peeler bail and platen.
Figure 10: Activating Peeler Bar (QLn320 Shown)
Peeler Bail (Pull up and flip down if using media in pell-off mode
4
Peeler Lever
Latch Release
Lever
• Turn on the printer or press the Feed button on the front of the printer if the printer is already on. The printer will advance the media to the next label, if printing labels. If you are printing on journal media, the printer will advance a short strip of media.
To disengage the peeler bail, first open the media cover as previously described. The peeler bail will automatically return to the
Up position.
Press straight down on the peeler bail to lock it in place in its original home position.
29
QLn Series User Guide
Loading Media in Peel-off Mode (QLn420)
• If you plan to use the printer in the peel-off mode, peel a few labels off of the media and load the media as previously described.
• Close the media cover.
• Lift up on the peeler lever located on the side of the printer below the media cover button.
• Lock the peeler lever in the “up” position to fully engage the peeler bail.
Figure 11: Activating Peeler Bar (QLn420 Shown)
Peeler Bail
Media Cover
Button
Peeler Lever
• Turn on the printer or press the Feed button on the front of the printer if the printer is already on. The printer will advance the media to the next label, if printing labels.
If you are printing on journal media, the printer will advance a short strip of media.
Note • Peeler will not work with most synthetic label stock since that media is softer and tends to adhere to its liner. However, the QLn420 printer is fully capable of printing on synthetic labels.
30
QLn Series User Guide
• To disengage the peeler bail, press the peeler release while pressing straight down on the peeler lever. This will disengage the peeler bail and return it to its original home position.
Note • Before disengaging the peeler, be sure there are no peeled labels present on the peeler bail. This could cause a label jam if you were to disengage with the peeled label present.
QLn Healthcare Printers
Zebra QLn Healthcare 2” and 3” printers are designed to meet the specific and unique needs of the healthcare environment. The healthcare application is based on the QLn220 and
QLn320 printers primarily for barcode label printing, but also retaining the QLn’s ability to print receipts.
The QLn220 and 320 Healthcare printers also offer a few key enhancements to these existing printers:
• Provide printers with distinctive gray and white healthcare colors (see Page 32) and performance plastics that can also be disinfected with the most common cleaners used in hospitals.
• Leverage the technology advancements made on the QLn platform, i.e. new User Interface, NFC, QR code.
• Add the MFi chip to the QLn main logic board to support
Bluetooth connectivity between the printer and an iOS device as Apple devices are expected to grow in popularity in this segment.
31
QLn Series User Guide
Figure 12: QLn Healthcare Printers
Since the QLn220 and 320 Healthcare are based on the
QLn220 and 320 platform, they are designed to be direct thermal printers which support variable print widths. They will provide a print experience compatible to the QLn220 and 320, specifically in the following areas:
• They will support the same barcodes, barcode quality, and visual print quality.
• They will offer equal wireless performance in terms of range, reliability, and speed.
• They will be compatible with all QLn220 and 320 accessories.
Due to the nature of the healthcare environment, QLn
Healthcare printers feature more rugged plastics designed and tested to withstand constant cleaning with all major hospital cleaners for the life of the printer.
Note • Refer to the Guide to Disinfecting and Cleaning QLn Healthcare
Printers (P1066640-001) for detailed cleaning instructions.
Note • Refer to the QLn Healthcare Printers Quick Start Guide (P1067208-
001) for more detailed information on these printers.
32
QLn Series User Guide
Operator Controls
The QLn Series printers come equipped with a keypad control panel and LCD graphical user interface. The standard control panel is illustrated in Figure 13, 13a, and 14. The LCD interface allows easy display and selection of many printer functions as detailed on following pages.
Standard Control Panel
The standard control panel has multiple control buttons and two multipurpose indicators.
• The Power Button turns the printer on and off.
Note • When turning on the QLn420 printer, press and hold the Power
Button between 1.5 and 2.5 seconds. When the LCD illuminates, release the Power Button. To turn off the printer, press and hold the Power Button until the printer shuts down.
• The Media Feed Button advances a length of media which is determined by the type of media being used. Label media will be advanced to the next gap or bar sense marker. Journal
(plain) media will be advanced by a length determined by the printer’s software.
• The LED Charge Indicator shows solid Yellow when charging, solid Green when fully charged, and is turned off when there’s a fault condition and the printer is plugged in.
• Four Way Navigation Buttons allow the user to scroll between functions on the LCD user space. (The Navigation Buttons do not apply to the Status Bar and Navigation Bar.)
• Enter Button allows the user to select the desired function highlighted on the LCD interface and is indicated by the word
“OK”.
• Two software defined function keys allow the user to select a function listed on the navigation bar.
33
QLn Series User Guide
Figure 13: Standard Control Panel (QLn320/220)
LED Charge Indicator
Solid Yellow: Charging
Solid Green: Fully charged
Off: No DC Power Applied
Off: With DC Power Applied: Charge Fault
Power Button
Press to turn unit on. There will be a 10 second boot up time.
Press again to turn unit off
Feed Button
Press to advance a blank label or a software determined length of journal media.
Figure 13a: Standard Control Panel (QLn420)
LED Charge Indicator
Solid Yellow: Charging
Solid Green: Fully charged
Off: No DC Power Applied
Off: With DC Power Applied: Charge Fault
Power Button
Press to turn unit on. There will be a 10 second boot up time.
Press again to turn unit off
34
QLn Series User Guide
Feed Button
Press to advance a blank label or a software determined length of journal media.
LCD Control Panel
The 240x128 pixel LCD control panel allows the user to view the status of the QLn Series printer and have access to various printer alerts and messages. It also has multi-directional keys which allow navigation and selection of menu options affecting printer functions. These keys allow scrolling through the various options and settings. The “OK” button allows selection of the option or function displayed on the screen.
The top of the screen has a row of status icons, or a Status
Bar, which indicate the state of various printer functions. The
Status Bar is located above the Status Screen shown below along with a Navigation Bar. The Status Screen is the default display and is shown at power up. When navigating the menus, the printer will automatically return to this screen when the user is done navigating after an appropriate delay.
Figure 14: LCD Control Panel (QLn320/220)
Printer Status Bar
I ndicates the status of several printer functions.**
Status Screen
Default screen the printer will display when the user is not navigating the main menu screen.
Navigation Bar
Displays user-selectable options.
Soft Keys
Press to select a function on the Navigation Bar.
Select Button
Press to select a menu choice on the Status Screen.
Four Way Navigation
Buttons
Scroll through menu choices on Status Screen
Press “OK” to enter.
** Not every icon will be displayed on the Status Bar at one time, only those applicable to the printer’s configuration.
35
QLn Series User Guide
Status Bar Icons
Indicates Bluetooth® connection status. The icon will blink to show that the printer is receiving label data via
Bluetooth, and is solid when link is established. This icon appears only on printers with the Bluetooth wireless option installed.
Indicates that the printer is connected to a radio network via 802.11 protocols. The antenna icon will blink with no parentheses when looking for an access point. One set of solid parentheses with blinking antenna indicates WLAN is associated and attempting authentication.
Two sets of solid parentheses and solid antenna indicate the printer is successfully connected to the WLAN.
The icon and two parentheses will blink to show the printer is receiving printer data via WLAN. The four (4) bars indicate the strength of the WLAN connection to the access point. These icons appear only with the
802.11 radio installed.
The Ethernet icon will blink when the printer is receiving label data via the Ethernet connection. It will not be displayed on the status bar when the Ethernet is inactive.
This icon appears only when the Ethernet option is installed and the printer is docked in Ethernet cradle.
The Data icon indicates data being sent to the printer, i.e. the icon will blink when there is a label data transmission via the serial or USB ports.
The Media Out icon will blink when there is no media in the printer and will not blink when there is media in the printer.
The Head Latch icon indicates if the media cover is closed or not properly latched. It will appear unlocked and blinking if open and will not appear if the cover is closed.
36
QLn Series User Guide
The Error icon will be displayed and blink if an error condition exists. The icon will not be displayed if no printer error exists. Since there are separate icons for Media
Out and Head Latch Open, these two alerts do not apply to the Error icon.
The Battery Charge Level icon indicates the reported state of charge from the battery pack. In a non-charging state, four (4) bars indicates the battery level is greater than 80%. Three (3) bars indicates if the battery level is less than or equal to 80% but greater than 60%. Two (2) bars indicates if the level is less than or equal to 60% but greater than 40%. One (1) bar indicates if the battery level is less than or equal to 40% but greater than 20%. And zero (0) bars indicates if the level is less than or equal to
20%.
While the battery is charging, a lightning bolt will appear in the battery icon to indicate that charging is taking place.
When the battery is charging and fully charged, four bars will be displayed. When the battery is charging and the level is greater than 80%, the battery icon will alternate between four bars and three bars. When the battery is charging and the level is less than or equal to 80% but greater than 60%, the icon will alternate between three bars and two bars. When the battery is charging and the level is less than or equal to 60% but greater than 40%, the icon will alternate between two bars and one bar. When the battery is charging and the level is less than or equal to 40% the icon will alternate between one bar and zero bars.
37
QLn Series User Guide
Main Menu Screen (QLn320/220)
The user can select options on the Main Menu screen by pressing the soft key located beneath the Menu option on the navigation bar. The Main Menu screen displays graphical options including Communication, Display, Media, Settings,
Battery, and Help.
Note • The QLn Healthcare printers feature a different menu system. See
Page 40 for details.
Figure 15: Main Menu Screen (QLn320/220)
Info (Help)
Icon
The user can scroll between icons using the four-way arrow buttons. When an icon is highlighted, its text description will be displayed in the middle of the navigation bar, and can be selected by pressing the “OK” button. This will take the user to the screen with status information specific to that option. The
Info (or Help) menu provides useful information on a variety of topics. Please explore this menu to become more familiar with your printer and how it operates.
The QLn Series printers will also display various alerts, such as “Media Out”, “Media Cover Open”, or “Battery Low”. The user can respond to questions by pressing one of the soft keys to indicate that an action has been taken to address the alert in question. Once the condition causing the alert has been addressed (i.e. loading media), the alert message will be cleared. (See Appendix H for a complete list of alerts for the
QLn Series printers.)
38
QLn Series User Guide
Soft Keys
Programmable LCD Settings
In addition to the status icons, the LCD control panel can display other printer settings and functions as text. Applications can be written to allow the user to view and /or modify these settings using the scroll and select keys on the display. The menu that comes with the printer provides access to the most commonly used parameters. Refer to the Programming Guide
(p/n P1012728-008) for a complete list of the parameters, and for details on how to change the front panel display at www.zebra.com/manuals).
The LCD backlighting option allows viewing of the screen in a dark environment, or provides better contrast in a very bright environment. The QLn320 and QLn220 can be programmed to enter a low power mode (Backlight Off) during periods of front panel inactivity. While in low power mode, the screen is populated with menus and status icons, data which may or may not be readable depending on ambient light conditions. The QLn
Series printers provide a configurable time delay from the time the backlight is turned on to when it turns off. The time range for this delay is 5 to 1200 seconds with a default time of 10 seconds. The backlight can be activated within one second after any of the cursor, select, or soft keys is pressed. (The feed button does not activate the backlight.) The status bar icons, the user space content, and the navigation bar will remain on the screen with the backlight off. Extensive use of the display backlight will decrease the time the printer can run between charges. Refer to the section “Extending Battery Life” for more information.
39
QLn Series User Guide
Home Menu Screen (QLn420 and QLn Healthcare Printers)
The QLn420 and QLn Healthcare printers share the same control panel. The printer’s control panel includes a display where the user can view the printer’s status or change its operating parameters. After the printer completes the power-up sequence, it moves to the Idle Display screen
(Figure 21). This screen includes the printer’s current status, information such as firmware version and IP address, and a
Home menu shortcut.
The Home Menu for the printer uses a different set of icons than the standard QLn320 and QLn220, uses larger fonts for enhanced readability, and also provides support for multiple languages. The Home Menu screen displays graphical parameter options including Settings, Tools, Network, Battery,
Language, Sensors, Ports, and Bluetooth (as shown in Figure
22). These options allow the user to view the printer’s status or change its operating parameters.
Figure 16: Idle Display Screen (QLn420 and QLn Healthcare)
PRINTER READY
V68.18.3z
Current
Status
Home
Icon menu (Figure 22). Click on the Home icon located on the Idle
Display screen to proceed to the Home Menu.
The user can scroll between icons using the four-way arrow buttons. When an icon is highlighted, its text description will be displayed in the middle of the navigation bar, and can be selected by pressing the “OK” button. This will take the user to the screen with status information specific to that option.
40
QLn Series User Guide
Figure 17: Home Display Screen (QLn420 and QLn Healthcare)
SETTINGS
Icon Parameter
See Settings menu in Appendix D
See Toolss menu in Appendix D
See Network menu in Appendix D
See Battery menu in Appendix D
See Language menu in Appendix D
See Sensors menu in Appendix D
See Ports menu in Appendix D
See Bluetooth menu in Appendix D
41
QLn Series User Guide
Whereas the QLn320 and 220 printers have multiple line items per screen, the QLn420 and QLn Healthcare printers display one setting per screen using larger fonts (as shown below). In order to navigate to the next setting, click on the right arrow button. Click on the soft key below the Home icon to return to the Home Menu screen to choose a different parameter.
Figure 18: Print Settings Example
DARKNESS
-49
Some parameter settings have a scroll option to view multiple setting choices. This option is identifiable by the presence of up and down arrows located on either side of the display
(Figure 24). For example, the Tools parameter has a Help option for many printer functions such as media, battery icon, error icon, latch icon, media icon, receive data icon, ethernet icon, signal icon, WLAN icon, Bluetooth icon, power LED, printhead, and battery.
42
QLn Series User Guide
Press the up and down arrows on the keypad to scroll through a setting’s various options. Press the left and right arrows to scroll to the next setting.
Figure 19: Scroll Option (Help Settings)
Scroll
Indicator
HELP FOR
MEDIA
GET HELP
Scroll
Indicator
Soft Key
Keypad
Press the soft key beneath the “GET HELP” command on the display in this example to receive basic help information for loading media in the printer (Figure 20).
Figure 20: Scroll Details (Help For Media) screen.
1: Open media cover by pressing down on the gold release button on right hand side of the printer.
BACK
OK
43
QLn Series User Guide
Verify the Printer is Working
Before you connect the printer to your computer or portable data terminal, make sure that the printer is in proper working order. You can do this by printing a configuration label using the “two key” method. If you can’t get this label to print, refer to
“Troubleshooting”.
Printing a Configuration Label
1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back)
2. Press and hold the Feed Button.
3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button. The unit will print a line of interlocking “x” characters to ensure all elements of the print head are working, print out the version of software loaded in the printer and then print the report.
Note that the report can also be printed from the Info (Help) menu on the LCD.
The report indicates model, serial number, baud rate, and more detailed information on the printer’s configuration and parameter settings. (See the Troubleshooting Section for sample printouts and a further discussion on how to use the configuration label as a diagnostic tool.)
44
QLn Series User Guide
Connecting the Printer
The printer must establish communications with a host terminal which sends the data to be printed. Communications occur in four basic ways:
• QLn Series printers can communicate by cable via either
RS-232C or USB 2.0 protocols. USB drivers are included in the Zebra Designer Driver which can be downloaded from www.zebra.com/drivers.
• By means of a wireless LAN (Local Area Network) per
802.11 specifications. (Optional)
• By means of the Ethernet when docked on the Ethernet cradle. (Optional)
• By means of a Bluetooth short range radio frequency link.
(Optional)
• WinMobile®, Blackberry®, and Android® devices use standard Bluetooth protocol.
• QLn Series printers are compatible with iOS devices, therefore printing via Bluetooth to an Apple® device is possible.
45
QLn Series User Guide
Cable Communication
Caution • The printer should be turned off before connecting or disconnecting a communications cable.
The QLn Series printers can communicate by cable; the specific cable supplied with your printer will vary with the host terminal and your model printer.
RS-232C Communications
The 14-pin serial connector on your communications cable plugs into the serial communications port on the side of the printer. QLn Series printers also have a USB port.
USB Communications
The small 5-pin connector on the USB cable plugs into the printer. The connectors are keyed to assure correct alignment; do not try to force the cable if it does not plug in.
Figure 21: Communication Options (QLn320 Shown)
Communications
Port
Communications Cable to Terminal.
Part #’s vary. Refer to Appendix A.
RS-232C or USB Communications
Cable to Computer.
(Refer to Appendix A for part #’s.
46
QLn Series User Guide
The other end of the cable must be plugged into the host terminal as shown in Figure 21, or to a serial or USB port on a computer (Figure 21). The QLn Series is configured with the
USB Open HCI interface driver allowing it to communicate with Windows® based devices.
USB drivers are included in the Zebra Designer Driver which can be downloaded from the Zebra Web site. Other terminals or communications devices may require the installation of special drivers to use the USB connection. Consult the factory for further details.
Providing Strain Relief for Communications Cable
If you are connecting either a USB or RS-232 communications cable to the printer permanently, access the communications port on the side of the printer next to the latch release lever.
Plug the connector into the appropriate port and align the plastic locking cap with the cut outs shown below. Rotate the locking cap clockwise to lock the cable in place. (Turn counter clockwise to unlock the cable.) Once locked in place, this provides strain relief for the cable and will prevent the cable from disconnecting from the printer.
Note • Only one cabel can be present in the USB/RS-232 communications port at a time for strain relief purposes.
Figure 22: Communications Port (QLn420 Shown)
Align locking connector with these cut-outs.
RS-232 Port
USB Port
Align locking connector with these cut-outs.
47
QLn Series User Guide
Figure 23: Communications Port Strain Relief (QLn420 Shown)
Rotate locking cap in a clockwise direction to lock cable in place..
48
QLn Series User Guide
Wireless Communications with Bluetooth
Bluetooth is a worldwide standard for the exchange of data between two devices via radio frequencies. This form of point- topoint communication does not require access points or other infrastructure. Bluetooth radios are relatively low powered to help prevent interference with other devices running at similar radio frequencies. This limits the range of a Bluetooth device to about
10 meters (32 feet). Both the printer and the device it communicates with must follow the Bluetooth standard. Other than conditions specified elsewhere in this manual, only one of the radio options can be installed in the printer at one time and the antenna used for these transmitters must not be co-located or must not operate in conjunction with any other antenna.
Bluetooth Networking Overview
Each Bluetooth enabled QLn Series printer is identified by a unique Bluetooth Device Address (BDADDR). This address resembles a MAC address whereby the first three bytes are vendor, and the last three bytes are device (e.g. 00:22:58:3C:B8:CB).
This address is labeled on the back of the printer via a barcode for ease of pairing. (See Page 34.) In order to exchange data, two
Bluetooth enabled devices must establish a connection.
Bluetooth software is always running in the background, ready to respond to connection requests. One device (known as the master or the client) must request/initiate a connection with another. The second device (the slave or the server) then accepts or rejects the connection. A Bluetooth enabled QLn Series printer will normally act as a slave creating a miniature network with the terminal sometimes referred to as a “piconet”.
Discovery identifies Bluetooth devices that are available for pairing whereby the master device broadcasts a discovery re- quest and devices respond. If a device is not discoverable, the master cannot pair unless in knows the BDADDR or has previously paired with the device.
Bluetooth 2.1 or higher uses Security Level 4 Secure Simple
Pairing (SSP), a mandatory security architecture that features four
(4) association models: Numeric Comparison, Passkey Entry, Just
Works (no user confirmation), and Out of Band (pairing info transmitted OOB, e.g. via Near Field Communication).
49
QLn Series User Guide
Figure 24: Bluetooth Security Modes
Security Mode 1
If a BT>/= 2.1 device is pairing with a BT</= 2.0 device, it falls back to BT 2.0 compatibility mode and behaves the same as
BT 2.0. If both devices are BT
>/= 2.1, Secure Simple Pairing must be used according to the
BT spec.
Security Mode 2
If a BT >/= 2.1 device is pairing with a BT </= 2.0 device, it falls back to BT 2.0 compatibility mode and behaves the same as
BT 2.0. If both devices are BT
>/= 2.1, Secure Simple Pairing must be used according to the
BT spec.
Security Mode 3
If a BT >/= 2.1 device is pairing with a BT </= 2.0 device, it falls back to BT 2.0 compatibility mode and behaves the same as
BT 2.0. If both devices are BT
>/= 2.1, Secure Simple Pairing must be used according to the
BT spec.
Security Mode 4: Simple Secure Pairing
Simple Secure Pairing: a new security architecture introduced supported in BT >= 2.1.
Service-level enforced, similar to mode 2. Mandatory when both devices are BT >= 2.1.
There are four association models currently supported by mode 4. Security requirements for services must be classified as one of the following: authenticated link key required, unauthenticated link key required, or no security required. SSP improves security through the addition of ECDH public key cryptography for protection against passive eavesdropping and man-inthe-middle (MITM) attacks during pairing.
Numeric Comparison
Designed for situation where both devices are capable of displaying a six-digit number and allowing user to enter
“yes” or “no” response.
During pairing, user enters “yes” if number displayed on both devices matches to complete pairing. Differs from the use of PINs in legacy (BT<=2.0) pairing because the number displayed for comparison is not used for subsequent link key generation, so even if it is viewed or captured by an attacker, it could not be used to determine the resulting link or encryption key.
Passkey Entry
Designed for situation where one device has input capability but no display (e.g. keyboard), while other device has a display. The device with a display shows a six-digit number, then the user enters this key on the device with input. As with numeric comparison, the six-digit number is not used in link key generation.
Just Works
Designed for situation where one (or both) of the pairing devices has neither a display nor keyboard for entering digits (e.g. Bluetooth headset). It performs authentication step 1 in the same manner as as numeric comparison, but the user cannot verify that both values match, so MITM
(man-in-the-middle) protection is not provided.
This is the only model in SSP that does not provide authenticated link keys.
Out of Band (OOB)
Designed for devices that support a wireless technology other than
Bluetooth (e.g. NFC) for the purposes of device discovery and cryptographic value exchange. In the case of NFC, the OOB model allows devices to pair securely by simply tapping one device against the other, followed by the user accepting the pairing via a single button push. Security against eavesdropping and MITM attacks is dependant on the OOB technology.
Each mode, except for Just Works, has Man-In-The-Middle
(MITM) protection, meaning no third device can view the data being passed between the two devices involved. The SSP mode is usually negotiated automatically based on the capabilities of both the master and slave. Lower security modes can be disabled via the bluetooth.minimum _ security _ mode SGD. The bluetooth.minimum _ security _ mode SGD sets the lowest security level at which the printer will establish a Bluetooth connection. The printer will always connect at a higher security level if requested by the master device. To change the security mode and security settings in the QLn Series printers, use Zebra Setup
Utilities.
50
QLn Series User Guide
Figure 25: Bluetooth Minimum Security Modes
BT Version of Master Device (>2.1) bluetooth.minimum_security_mode=1 bluetooth.minimum_security_mode=2 bluetooth.minimum_security_mode=3 bluetooth.minimum_security_mode=4
Secure Simple Pairing
Just Works/Numeric Comparison
Secure Simple Pairing
Just Works/Numeric Comparison
Secure Simple Pairing
Numeric Comparison
Secure Simple Pairing
Numeric Comparison bluetooth.bluetooth_PIN
Not Used bluetooth.minimum _ security _ mode sets the lowest security level at which the printer will establish a Bluetooth connection. The printer will always connect at a higher security level if requested by the master device.
The QLn Series printers also feature bonding for Bluetooth. The printer caches pairing info so devices stay paired through power cycles and disconnects. This eliminates the need to re- pair on every connection establishment.
The bluetooth.bonding SGD is on by default.
Note • For detailed information on Bluetooth, please refer to the
Bluetooth Wireless User Guide (P1068791-001) at: http://www.zebra.com/us/en/support-downloads.html
In addition, the QLn Series printers support Near Field
Communication (NFC) technology. Using the “Print Touch” feature located on the side of the printer, end-users can automatically connect via Bluetooth from a handheld device that supports
NFC technology. The NFC tag has the printer’s BDADDR encoded in a URL on the tag. Simply touching the NFC handheld device to the “Print Touch” icon on the printer will connect and pair the handheld device to the printer.
51
QLn Series User Guide
WLAN Overview
QLn Series printers can be equipped with a radio that uses the industry standard 802.11 protocols. They will have the FCC ID number on the serial number label on the back of the unit.
• QLn Series Wireless Network Printers with the Zebra
802.11 WLAN radio module can be identified by the text
“Wireless Network Printer” on the serial number label on the back of the printer.
• These printers allow communication as a node within a wireless local area network (WLAN). Methods of establishing communications to the printer will vary with each application.
More information and LAN configuration utilities are included in the Zebra Net Bridge™ program (version 2.8 and later). Zebra
Setup Utilities (ZSU) can also be used to configure WLAN communications settings. Both Net Bridge and ZSU may be downloaded from the Zebra Web site.
Setting Up the Software
QLn Series printers use Zebra’s CPCL and ZPL Programming languages which were designed for mobile printing applications.
CPCL and ZPL are fully described in the ZPL Programming Guide
(p/n P1012728-008) available on-line at www.zebra.com/manuals.
You can also use Designer Pro, Zebra’s Windows
®
based label creation program which uses a graphical interface to create and edit labels in either language.
Refer to Appendix F for tips on downloading the Designer Pro application from Zebra’s Web site.
52
QLn Series User Guide
Setting Up the Software
QLn Series printers use Zebra’s CPCL and ZPL Programming languages which were designed for mobile printing applications.
CPCL and ZPL are fully described in the ZPL Programming Guide
(p/n P1012728-008) available on-line at www.zebra.com/manuals.
You can also use Designer Pro, Zebra’s Windows
®
based label creation program which uses a graphical interface to create and edit labels in either language.
Refer to Appendix G for tips on downloading the Designer Pro application from Zebra’s Web site.
Near Field Communication (NFC)
Much like Bluetooth and Wi-Fi technologies, Near Field
Communication (NFC) allows wireless communication and data exchange between digital devices like smartphones. Yet NFC utilizes electromagnetic radio fields while technologies such as
Bluetooth and Wi-Fi focus on radio transmissions instead.
NFC is an offshoot of Radio Frequency Identification (RFID), with the exception that NFC is designed for use by devices within close proximity to each other, i.e. a smartphone and a QLn Series printer. NFC allows these devices to establish communication with each other by touching them together or bringing them into proximity, usually no more than 7.62 centimeters (3 inches). Three forms of NFC technology exist: Type A, Type B, and FeliCa. All are similar but communicate in slightly different ways. FeliCa is commonly found in Japan.
Devices using NFC may be
active
or
passive
. A passive device, such as a QLn Series printer with an NFC tag, contains information that other devices can read but does not read any information itself.
An active device, such as a smartphone, can read the information on the printer’s NFC tag, but the tag itself does nothing except transmit the info to authorized devices.
53
QLn Series User Guide
Active devices can read information and send it. An active NFC device, like a smartphone, would not only be able to collect information from NFC tags, but it would also be able to exchange information with other compatible phones or devices. An active device could even alter the information on the NFC tag if authorized to make such changes. To ensure security, NFC often establishes a secure channel and uses encryption when sending sensitive information.
Figure 26: Near Field Communication (NFC) Pairing http://www.zebra.com/nfc
Note • Tapping the Zebra Print Touch TM icon with a Near Field
Communication (NFC) enabled smartphone will provide instant access to printer-specific information. For more information about NFC and Zebra products, go to http://www.zebra.com/nfc.Bluetooth pairing applications via NFC is also possible. Please see Zebra Multi-platform SDK for more information.
54
QLn Series User Guide
QLn Series Accessories
Swivel Belt Clip
Most QLn Series printers have a plastic swivel belt clip installed as a standard feature. (It should be noted that QLn220
& 320 printers with extended capacity battery do not come equipped with a belt clip.) To use: hook the clip over your belt, and ensure that the clip is securely attached to the belt. The belt clip will pivot to allow you to move freely while wearing the printer. The QLn420 also provides a more rigid metal belt clip as an option.
In order to install or remove the plastic Belt Clip you will need to remove the battery pack.
Figure 27: Using the Belt Clip (QLn420 Shown)
Plastic Belt Clip Metal Belt Clip
Clip printer to belt
Printer can pivot freely
55
QLn Series User Guide
Soft Case
QLn Series printers have soft case options that also allow you to carry the printer from your belt. The QLn420 soft case can be ordered through accessory kit number P1050667-017, the QLn320 is P1031365-029, and the QLn220 accessory kit is
P1031365-044.
Figure 28: Using the Soft Case
Hard Case
The QLn420 printer has a two piece hard case option that also allows you to carry the printer from your belt, while also providing increased protection for the printer. It pivots via a hinge located on the back and snaps into place in front as shown above. The metal belt clip is mounted to the hard case and printer with two screws. If no belt clip is used, two shorter screws are used to hold the printer to the hard case.
Figure 29: Using the QLn420 Hard Case
56
QLn Series User Guide
Adjustable Shoulder Strap
Refer to Figure 30 if your printer is equipped with the shoulder strap option (p/n P1031365-092).
Figure 30: Using the Optional Shoulder Strap
1. Insert the end of the shoulder strap behind the post on the front side of the printer and loop it around the post.
2. Slide the end of the strap under the plastic buckle (circled).
3. Slide the end of the strap under the opposite side of the plastic buckle (as shown). Pull to tighten the strap inside the buckle.
4. Repeat the same steps on the opposite side of the printer.
57
QLn Series User Guide
Hand Strap
The QLn Series hand strap accessory (p/n P1031365-027) attaches to the printer’s cut-outs as does the shoulder strap to provide the user with a convenient and secure method of carrying the printer. To attach the hand strap to the printer:
• Insert the end of the strap through the cut out on the front of the printer as shown below.
• Loop the end of the strap back around the cut out and secure it over the button.
• Repeat this process for the opposite end of the strap.
Figure 31: Hand Strap (QLn420 Shown)
The QLn Series printers also feature two mounting holes on the base of the printer to accommodate future mounting options. Refer to RAM Mount Installation Procedure
(p/n AA17518-003) on zebra.com.
58
QLn Series User Guide
Preventive Maintenance
Extending Battery Life
• Never expose the battery to direct sunlight or temperatures over 40° C (104° F) when charging.
• Always use a Zebra charger designed specifically for Lithium-
Ion batteries. Use of any other kind of charger may damage the battery.
• Use the correct media for your printing requirements. An authorized Zebra re-seller can help you determine the optimum media for your application.
• If you print the same text or graphic on every label, consider using a pre-printed label.
• Choose the correct print darkness, and print speed for your media.
• Use software handshaking (XON/XOFF) whenever possible.
• Remove the battery if the printer won’t be used for a day or more and you’re not performing a maintenance charge.
• Consider purchasing an extra battery.
• Remember that any rechargeable battery will lose its ability to maintain a charge over time. It can only be recharged a finite number of times before it must be replaced. Always dispose of batteries properly. Refer to Appendix E for more information on battery disposal.
General Cleaning Instructions
Caution • Avoid possible personal injury or damage to the printer. Never insert any pointed or sharp objects into the printer. Always turn off the printer before performing any cleaning procedures. Use care when working near the tear bars as the edges are very sharp.
Warning • The printhead can get very hot after prolonged printing. Allow it to cool off before attempting any cleaning procedures.
Only use a Zebra cleaning pen (not supplied with the printer) or a cotton swab with 90% medical grade alcohol for cleaning the printhead.
Caution • Use only cleaning agents specified in the following tables.
Zebra Technologies Corporation will not be responsible for damage caused by any other cleaning materials used on this printer.
59
QLn Series User Guide
QLn Series Cleaning
Printhead
Area Method
Use a Zebra cleaning pen to swab the thin gray line on the printhead, cleaning the print elements from the center to the outside edges of the printhead.
Interval
After every five rolls of media (or more often, if needed). When using l i n e r l e s s t y p e m e d i a , cleaning is required after every roll of media.
Platen Surface
(Linered)
Platen Surface
(Linerless)
Scraper (Linerless Units
Only)
Rotate the platen roller and clean it thoroughly with a fiber-free swab, or lint free, clean, damp cloth lightly moistened with medical grade alcohol (90% pure or better) (Fig. 32a/Fig. 32b).
Rotate platen roller and clean with a fiber-free swab and 1 part liquid soap
(Palmolive or Dawn) and 25 parts water. Use pure water to clean after soap/water mixture.
Use adhesive side of media to clean scraper on linerless units. (Fig. 32b)
After every five rolls of media (or more often, if needed)
Clean platen only if there is an issue during printing, i.e. media not releasing from the platen. (*See Note below.)
After every five rolls of media (or more often, if needed).
Tear Bar
Printer Exterior
Printer Interior
Interior of units with
Linerless Platens
Clean thoroughly with 90% medical grade alcohol and a cotton swab. (Fig. 32a)
Water-dampened cloth or
90% medical grade alcohol wipe.
Gently brush out printer.
Ensure the Bar Sensor and
Gap Sensor windows are free of dust. (Fig. 32a)
Clean thoroughly with 90% medical grade alcohol and a fiber-free swab. (See Fig.
32b for specific target areas for interior cleaning.)
As needed
As needed
As needed
After every five rolls of media (or more often, if needed).
Note: This is an emergency procedure only to remove foreign contaminates (oils, dirt) from the platen that can damage the printhead or other printer components. This procedure will shorten or even exhaust the linerless platen’s useable life. If the linerless media continues to jam after cleaning and feeding 1 to 2 meters (3 to 5 feet) of media, replace the platen.
60
QLn Series User Guide
Important: The above cleaning procedures are not for QLn Healthcare printers. Refer to the Guide to Disinfecting and Cleaning QLn Healthcare
Printers (p/n P1066640-001) for detailed cleaning instructions.
Figure 32a: Cleaning the QLn Series Printers (Linered)
Peeler Bar
Platen Roller
Bar Sensor
Gap Sensor
Printhead
Elements
Tear Bar
Peeler Bail
Figure 32b: Cleaning the QLn Series Printers (Linerless)
Label Presence-
Sensor
Scraper
Platen Roller
Platen Holder
Printhead
Elements
Media Support
Disk
Media Support
Media Support
Disk
Media Support
61
QLn Series User Guide
Troubleshooting
Figure 33: Control Panels
Front Control Panel
QLn420
Green/Yellow
LED
QLn320/220
Status Icons
LCD Control Panel
Front Control Panel
If the printer is not functioning properly, refer to the chart below to find the state of the LED charge indicator on the
Front Control Panel. Then refer to the Troubleshooting topic referenced in the chart to resolve the problem. Please note that the charge LED is only on when DC power is applied to the printer. If no DC power is applied the LED is off, which does not apply to the table below.
Green
Solid
Off
Off
Yellow
Off
Solid
Off
Indication
Fully Charged
Charging
Fault
Ref. to Topic n/a n/a
1
62
QLn Series User Guide
LCD Control Panel Indicators
The top of the display shows several icons which indicate the status of various printer functions. Check the indicator status, then refer to the Troubleshooting topic referenced in the chart to resolve the problem.
Icon Status
On
Not Present
Blinking
Antenna Blinking
Antenna Blinking/1 Parenthesis
Steady
Antenna and 2 Parentheses
Steady
Antenna and 2 Parentheses
Blinking
Not Present
4 Bars
3 Bars
2 Bars
1 Bar
0 Bars
4 Blinking w/ Lightning Bolt
3 Blinking w/ Lightning Bolt
2 Blinking w/ Lightning Bolt
1 Blinking w/ Lightning Bolt
0 Bars w/ Lightning Bolt
Indication
Bluetooth link established
Bluetooth link inactive
Connecting or transmitting labels
Looking for AP
WLAN Associated & Attempting
Authentication
WLAN Associated and
Authenticated
Receiving Data
No Radio Present
>80% charged
60%-80% charged
40%-60% charged
20%-40% charged
Low Battery
Charging >80% Capacity
Charging 60-80% Capacity
Charging 40-60% Capacity
Charging 20-40% Capacity
Charging <20% Capacity
Blinking
Blinking
Steady
Not Present
Blinking
Steady
Media cover open
Receiving data
Ethernet Connected
No Ethernet Connection
Data processing in progress
No data being processed
63
QLn Series User Guide
Blinking
Steady
Blinking
Not Present
4 Bars
3 Bars
2 Bars
1 Bar
0 Bars
Out of Media
Media present
Error exists (excluding
Media Out and Head
Latch Open)
No error exists
802.11 signal strength
> 75%
802.11 signal strength
</= 75%
802.11 signal strength </= 50% but
>25%
802.11 signal strength
</= 25%
No Signal Strength
Troubleshooting Topics
1. No power:
• Check that battery is installed properly.
• Recharge or replace battery as necessary.
Caution: Always dispose of batteries properly. Refer to Appendix F for more information on proper battery disposal.
2. Media does not feed:
• Be sure media cover is closed and latched.
• Check spindle holding media for any binding.
• Ensure most recently printed label is removed (only in peel mode).
• Ensure label sensor is not blocked.
3. Poor or faded print:
• Clean print head.
• Check quality of media.
4. Partial or missing print:
• Check media alignment.
• Clean print head.
• Ensure media cover is properly closed and latched.
64
QLn Series User Guide
5. Garbled print:
• Check baud rate.
6. No print:
• Check baud rate.
• Replace battery.
• Check cable to terminal.
•Establish RF Link and/or restore LAN associativity.
•Invalid label format or command structure. Place printer in
Communications Diagnostic (Hex Dump) Mode to diagnose problem.
7. Reduced battery charge life:
• If battery is older than 1 year old, short charge life may be due to normal aging.
• Check battery health.
• Replace battery.
8. flashing:
• Flashing Data icon is normal while data is being received.
9. or flashing:
• Check that media is loaded and that the media cover is closed and securely latched.
10. Communication error:
•Check baud rate.
•Replace cable to terminal.
11. Label jam:
•Open head release latch and media cover.
•Remove and reinstall media.
12. Skip Labels:
• Check media for top of form sense mark or label gap.
• Check that the maximum print field has not been exceeded on label.
• Ensure bar or gap sensor is not blocked or malfunctioning.
65
QLn Series User Guide
13. Blank LCD screen:
• Make sure printer is turned on.
• No application loaded or application corrupted: reload program.
14. No NFC Connectivity
• Ensure smartphone is positioned 3 inches (7.62 cm) or closer to the Print Touch icon on the side of the printer.
Troubleshooting Tests
Printing a Configuration Label
To print out a listing of the printer’s current configuration fol- low these steps:
1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back).
2. Press and hold the Feed Button.
3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button.
Note: The configuration report can also be printed from the Info (Help) menu on the LCD.
Refer to Figures 34, 34a, and 34b for sample configuration printouts.
Communications Diagnostics
If there is a problem transferring data between the computer and the printer, try putting the printer in the Communications
Diagnostics Mode (also referred to as the “DUMP” mode). The printer will print the ASCII characters and their text representation
(or the period ‘.’, if not a printable character) for any data received from the host computer.
To enter Communications Diagnostics Mode:
1. Print a configuration label as described above.
2. At the end of the diagnostics report, the printer will print:
“Press FEED key to enter DUMP mode”.
3. Press the FEED key. The printer will print: “Entering DUMP mode”.
66
QLn Series User Guide
To enter Communications Diagnostics Mode:
1. Print a configuration label as described above.
2. At the end of the diagnostics report, the printer will print:
“Press FEED key to enter DUMP mode”.
3. Press the FEED key. The printer will print: “Entering DUMP mode”.
Note • If the FEED key is not pressed within 3 seconds, the printer will print “DUMP mode not entered” and will resume normal operation.
4. At this point, the printer is in DUMP mode and will print the ASCII hex codes of any data sent to it, and their text representation (or “.” if not a printable character).
Additionally, a file with a “.dmp” extension containing the
ASCII information will be created and stored in the printer’s memory. It can be viewed, “cloned” or deleted using the Net
Bridge application. (Refer to the Net Bridge documentation for more information.)
To terminate the Communications Diagnostics Mode and re- turn the printer to normal operations:
1. Turn the printer OFF.
2. Wait 5 seconds.
3. Turn the printer ON.
Contacting Technical Support
If the printer fails to print the configuration label, or you en- counter problems not covered in the Troubleshooting Guide, contact Zebra Technical Support. Technical Support addresses and phone numbers for your area can be found in Appendix H of this manual. You will need to supply the following information:
• Model number and type (e.g. QLn320)
• Unit serial number (Found on the large label on the back of the printer, also found in the configuration label printout.
• Product Configuration Code (PCC) (15 digit number found on the label on the back of the unit)
67
QLn Series User Guide
Figure 34: QLn320 Configuration Label
Printhead Test
Identifies Printer as a QLn320
Printer Serial
Number
MFi Supported
68
QLn Series User Guide
Figure 34a: QLn320 Configuration Label (cont.)
802.11 radio option /n installed. This section details the radio’s network settings
Ethernet Information
Network Information
69
QLn Series User Guide
Peripherals Installed
Figure 34b: QLn320 Configuration Label (cont.)
Flash and RAM Memory
Installed
Maximum Label Size
Resident Human Readable
Fonts Installed
Files loaded in printer memory (includes prescaled or scalable fonts)
70
QLn Series User Guide
Specifications
Note • Printer specifications are subject to change without notice.
Printing Specifications
Parameter QLn320
Print Width Up to 74 mm
(2.91 in.)
Print Speed 101.6 mm (4 in.)/second without peeler
50.8 mm (2 in.)/second with peeler
QLn220
Up to 48 mm
(1.89 in.)
Same
Same
QLn420
Up to 104 mm
(4.1 in.)
Same
Same
Printhead
Burn Line to
Tear Edge
Distance
Printhead
Life
5.08 mm (0.20 in.)
2 million inches of paper feed
4.31 mm (0.17 in.)
Same
Print Density
203 dots/in. or better Same
Memory and Communications Specifications
Parameter
Flash Memory
QLn Series Printers
256 MB 1
4.06 mm (0.16 in.)
Same
Same
RAM Memory
Standard
Communications
Optional Wireless
Communication
Real Time Clock
(RTC)
Ethernet
128 MB 1
RS-232 serial port (14 Pin serial connector)
Configurable Baud rate (from 9600 to 115.2 Kbps), parity and data bits.
Software (X-ON/X-OFF) or hardware (DTR/
STR) communication handshake protocols.
USB 2.0 Full Speed Interface (12 Mbps)
Bluetooth v2.1 compatible 2.4 GHz SRRF link
Optional wireless LAN capabilities comply with
802.11a/b/g/n protocols
QLn420: BT 3.0 and 802.11a/b/g/n
Time and date under application control. Refer to
ZPL Programming Manual, available at www.zebra.com/manuals for RTC commands.
10 or 100 mps Ethernet auto detect when docked in cradle.
1. Memory configuration on your printer may be ascertained by printing a configuration label as detailed on page 66.
71
QLn Series User Guide
Label Specifications
Parameter
Max Media
Width
Max/Min Label
Length
Black Bar Sensor to Printhead
Burnline Distance
Label Thickness
QLn320
25.4 to 79.4 mm
(1.0 to 3.125 in.)
12.7 to 812.8 mm
(0.5 to 32 in.) maximum
15.87 mm (0.62 in.)
+/-
0.635 mm (0.025 in.)
0.058 to 0.165 mm
(0.002 to .0065 in.)
Max Tag/Receipt
Thickness
Max Label Roll
Outer Diameter
Inner Core
Diameters**
Black Mark
Location
Black Mark
Dimensions
0.152 mm
(0.006 in.)
66.8 mm (2.6 in.)
19 mm (0.75 in.) or
35.05 mm (1.38 in.) min. for linered
35.05 mm (1.38 in.) min. for linerless
The reflective media black marks should be centered on media roll
Minimum mark width:
12,7 mm (0.5 in.) perpendicular to inside edge of media, centered within the width of the roll.
Mark length: 3-11 mm (0.12 to 0.43 in.) parallel to inside edge of media.)
QLn220
16 to 55.37 mm
(.63 to 2.18 in.)
Same
QLn420
50.8 to 111.76 mm
(2.0 to 4.4 in.)
Same
13,46 mm (0.53 in.) 15.87 mm (0.62 in.)
+/-
0.635 mm (0.025 in.)
0.058 to 0.140 mm
(0.002 to .0055 in.)
0.061 to 0.190 mm
(0.0024 to 0.0075 in.)
0.152 mm
(0.006 in.)
55.8 mm (2.2 in.)
0.190 mm
(0.0075 in.)
66.8 mm (2.6 in.)
Same
Same
Same
Same
Same
Same
Same
Same
Note • Use Zebra brand direct thermal media that is outside wound. Media may be reflective (black mark) sensing, or transmissive (gap) sensing, diecut, continuous or linerless. For die-cut labels, use only full auto dies.
** QLn Series printers support coreless media which is 19 mm (0.75 in.) in inner diameter.
72
QLn Series User Guide
CPCL Font and Bar Code Specifications and Commands
Standard Fonts 25 bit-mapped fonts; 1 scalable font (CG Trimvirate
Bold Condensed*) *Contains UFST from Agfa Monotype Corporation Downloadable optional bit-mapped & scalable fonts via Net Bridge software.
Available Optional Fonts Optional International character sets: Chinese 16 x 16
(trad), 16 x 16 (simplified),24 x 24 (simplified); Japanese 16 x 16, 24 x 24
Linear Bar Codes Available
Barcode (CPCL Command)
Aztec (AZTEC)
Codabar (CODABAR, CODABAR 16)
UCC/EAN 128 (UCCEAN128)
Code 39 (39, 39C, F39, F39C)
Code 93 (93)
Code 128 (128)
EAN 8, 13, 2 and 5 digit extensions (EAN8, EAN82,
EAN85, EAN13, EAN132, and EAN135)
EAN-8 Composite (EAN8)
EAN-13 Composite (EAN13)
Plessey (PLESSEY) lnterleaved 2 of 5 (I2OF5)
MSI (MSI, MSI10, MSI1110)
FIM/POSTNET (FIM)
TLC39 (TLC39)
UCC Composite A/B/C (128(Auto))
UPCA, 2 and 5 digit extensions (UPCA2 and UPCA5)
UPCA Composite (UPCA)
UPCE, 2 and 5 digit extensions (UPCE2 and UPCE5)
UPCE Composite (UPCE)
MaxiCode (MAXICODE)
PDF 417 (PDF-417)
Datamatrix (using ZPL emulation) (DATAMATRIX)
QR Code (QR)
2-D Bar Codes Available
Rotation Angles
RSS:
RSS-14 (RSS-Subtype 1)
RSS-14 Truncated (RSS-Subtype 2)
RSS-14 Stacked (RSS-Subtype 3)
RSS-14 Stacked Omnidirectional
(RSS-Subtype 4)
RSS Limited (RSS-Subtype 5)
RSS Expanded (RSS-Subtype 6)
0°, 90°, 180°, and 270°
73
QLn Series User Guide
ZPL Font and Bar Code Specifications and Commands
Standard Fonts
Available Optional Fonts
15 bit-mapped fonts; 1 scalable font (CG Trimvirate
Bold Condensed*) Downloadable optional bitmapped & scalable fonts via Net Bridge software.
Zebra offers font kits covering multiple languages including Simplified and Traditional Chinese, Japanese,
Korean, Hebrew/Arabic, and others.
Linear Bar Codes Available
2-D Bar Codes Available
Rotation Angles
Barcode (CPCL Command)
Aztec (^B0)
Codabar (^BK)
Codablock (^BB)
Code 11 (^B1)
Code 39 (^B3)
Code 49 (B4)
Code 93 (^BA)
Code 128 (^BC)
DataMatrix (^BX)
EAN-8 (^B8)
EAN-13 (^BE)
GS1 DataBar Omnidirectional (^BR)
Industrial 2 of 5 (^BI) lnterleaved 2 of 5 (^B2)
ISBT-128 (^BC)
LOGMARS (^BL)
Micro-PDF417 (^BF)
MSI (^BM)
PDF-417 (^B7)
Planet Code (^B5)
Plessey (^BP)
Postnet (^BZ)
Standard 2 of 5 (^BJ)
TLC39 (^BT)
UPC/EAN extensions (^BS)
UPC-A (^BU)
UPC-E (^B9)
Maxi Code (^BD)
QR Code (^BQ)
0°, 90°, 180°, and 270°
74
QLn Series User Guide
9
10
11
12
13
14
Communication Ports
RS-232C
Pin # Signal Name
3
4
1
2
CTS
TXD
RXD
DSR
Type input output input input
7
8
5
6
GND
DTR
N/A
RTS
N/A
N/A
N/A
N/A
N/A
N/A output output
Description
Clear To Send from host
Transmit Data
Receive Data
Data Set Ready: low to high transition turns printer on, high to low transition turns printer off (if enabled)
Ground
Data Terminal Ready: set high when printer is on. Switched 5V (300mA max)
Do Not Use
Request To Send set high when printer is ready to accept a command or data
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
Do Not Use
10 12
Figure 35: RS-232C Communications Port
75
QLn Series User Guide
USB
Pin #
3
4
5
1
2
Signal Name
VBUS
USB-
USB+
USB_ID
Return
Type
bi-directional bi-directional
-
Description
USB Bus Power
I/O signals
I/O signals
Identifies A/B connector
Ground
5 1
Figure 36: USB Communications Port
Physical, Environmental and Electrical Specifications
Parameter
Weight w/ battery
Temperature
QLn320
1.6 lbs. (0.75 kg)
Operating: -20 °C to
50 °C
(-4 °F to 122 °F)
(Healthcare is 0 °C to 50
°C (32 °F to 122 °F
QLn220
1.35 lbs. (0.61 kg)
Operating:-20 °C to
55 °C
(-4 °F to 131 °F)
(Healthcare is 0 °C to
50 °C (32 °F to 122 °F
QLn420
2.2 lbs. (0.99 kg)
Operating: -20 °C to
50 °C
(-4 °F to 122 °F)
Relative Humidity
Battery
Storage: -25 °C to 65 °C
(-13 °F to 149 °F)
Charging: 0 °C to 40°C
(32 °F to 104 °F)
Operating/Storage:
10% to 90% non-condensing
Smart Battery (2 or 4 cell) Lithium-Ion, 7.4
VDC (nominal);
2.45 AHr min.
Same
Same
Same
Same
Same
Same
Same
Same
Intrusion
Protection (IP)
Rating
4 cell Extended Smart
Battery
(Optional)
IP43 (without optional environmental case)
IP54 (with case)
4 cell Extended Smart
Battery
(Optional)
IP43 (without optional environmental case)
IP54 (with case)
76
QLn Series User Guide
IP43 (without optional environmental case)
IP54 (with case)
Figure 37: QLn420 Overall Dimensions
82.5 mm
(3.25 in.)
Height
165.1 mm
(6.5 in.)
Width
77
QLn Series User Guide
Length
186.7 mm
(7.35 in.)
Figure 38: QLn320 Overall Dimensions
76.9 mm
(3.15 in.)
Height
117.9 mm
(4.65 in.)
Width
78
QLn Series User Guide
Length
173.7 mm
(6.85 in.)
Figure 39: QLn220 Overall Dimensions
72.4 mm
(2.85 in.)
Height
91.4 mm
(3.5 in.)
Width
79
QLn Series User Guide
Length
170.9 mm
(6.73 in.)
P1031365-050
P1031365-052
P1031365-053
P1031365-054
P1031365-055
P1031365-056
P1031365-057
P1031365-058
P1031365-059
P1031365-060
P1031365-061
P1031365-062
P1031365-063
P1031365-069
P1031365-092
Part #
P1031365-006
P1031365-018
P1031365-019
P1031365-022
P1031365-024
P1031365-027
P1031365-028
P1031365-029
P1031365-033
P1031365-038
P1031365-044
P1031365-045
QLn Series Accessories
Description
KIT ACC QLn220 RUBBER DOOR I/O (15)
KIT ACC QLn320 RUBBER DOOR I/O (15)
KIT ACC QLn220/QLn320 RUBBER DOOR DC JACK (15)
KIT ACC QLn220/320 PLATEN GEAR 48P 22T (25)
KIT ACC Mobile AC ADAPTER US (type A) cord
KIT ACC QLn HAND STRAP
KIT ACC QLn BELT CLIP REPLACEMENT (20)
KIT ACC QLn320 SOFT CASE (Includes Shoulder Strap)
KIT ACC QLn-EC AC ADAPTER US (type A) CORD (see
Sales for other countries)
KIT ACC QLN-EC
KIT ACC QLn220 SOFT CASE (Includes Shoulder Strap)
KIT ACC QLN-EC4 AC ADAPTER US CORD (see Sales for other countries)
KIT ACC EC4 WALL MOUNT
KIT ACC QLn Serial Cable (with strain relief) QL Adapter
(female DIN)
KIT ACC QLn Serial Cable, 6’ (with strain relief) PC-DB9
KIT ACC QLn Serial Cable (with strain relief) to MC9000
KIT ACC QLn PC-USB Cable, 6’ (with strain relief)
KIT ACC QLn Serial Cable (with strain relief) RJ45 to Telzon
Adapter
KIT ACC QLn Serial Cable (with strain relief) to LS2208
Scanner
KIT ACC QLn 16 PIN Serial Cable (with strain relief) to
MC3000
KIT ACC QLN220/QLN320 Spare Battery Smart
KIT ACC QLn 11 PIN Serial Cable (with strain relief) to
MC3000
KIT ACC QLn Serial DEX Cable (with strain relief)
KIT ACC QLn Serial Cable (with strain relief) to RJ45
Kit ACC SC2 Li-ION Smart Charger, US (type A) cord (see
Sales for other countries)
KIT, Acc QLn220/320 and ZQ500 Series Spare Extended
Battery with LED’s
KIT ACC QLn SERIES SHOULDER STRAP
80
QLn Series User Guide
QLn Series Accessories cont.
P1031365-104
P1050667-007
P1050667-010
P1050667-016
P1050667-017
P1050667-018
P1050667-026
P1050667-029
P1050667-030
P1050667-031
P1050667-032
P1050667-033
P1050667-034
P1050667-035
P1050667-036
P1050667-037
P1050667-038
P1050667-039
P1050667-040
P1050667-041
P1050667-042
P1050667-047
P1024458-002
AC18177-5
P1051378-002
KIT ACC QLn Serial Cable (with strain relief) to LS2208
Scanner Extended
KIT ACC QLn420 RUBBER DOOR I/O (15)
KIT ACC QLn420 RUBBER DOOR DC JACK (15)
KIT ACC QLn420 SPARE BATTERY
KIT ACC QLn420 SOFT CASE (Includes Shoulder Strap)
KIT ACC QLn420-EC AC ADAPTER US (type A) CORD (see
Sales for other countries)
KIT ACC QLn420-VC – 15V – 60V to 12V
KIT ACC QLn420-EC (NO ADAPTER, NO CORD
KIT ACC QLn420-VC (no adapter, no cord)
KIT ACC QLn420 METAL BELT CLIP
KIT ACC QLn420 Handi-Mount (compact, flexible RAM arm) with Base Plate
KIT ACC QLn420 Handi-Mount (compact, flexible RAM arm) without Base Plate
KIT ACC QLn420 ASSY HARD CASE W/METAL BELT CLIP
KIT ACC QLn420 Mobile Mount for Forklifts (with U-arm bracket and fanfold bin)
KIT ACC QLn420 SCREEN SCRATCH PROTECTOR OVERLAY
(25)
KIT ACC QLn420 MOBILE MOUNT PLATE
KIT ACC QLn420 DESKTOP STAND
KIT ACC QLn420 SOFT CASE W/O SHOULDER STRAP
KIT ACC QLn420 BATTERY ELIMINATOR WITH POWER
ADAPTER
KIT ACC QLn420 BATTERY ELIMINATOR NO ADAPTER
KIT, Acc Power Adapter for Mobile Battery Eliminator,
12~48V, open ended
KIT ACC QLn420 RAM MOUNT PLATE
BELT,CLIP,QLN,HC
Model UCLI72-4 Quad Battery Charger (US line cord, see
Sales for others)
BATTERY,PACK,LITHIUM,SMART,QLN HC
Note • Refer to Appendix A for additional information on Data I/O cables.
81
QLn Series User Guide
Appendix A
Interface Cables (RS-232 Cables)
Part Number P1031365-053; DB-9 to 14-Pin Serial
Part Number P1031365-052; 8-Pin DIN to 14-Pin Serial Cable
82
QLn Series User Guide
USB Cables
Part Number AT17010-1; USB A to USB Mini B Cable
- GND
- D+
- D-
- VBUS
- VBUS
- D-
- D+
- NC
- GND
Part Number P1031365-055; 4 Position USB Mini to 4-Pin USB
(w/ Strain Relief)
Note • Visit the Zebra website at: www.zebra.com/accessories for a listing of interface cables for all Zebra mobile printers.
83
QLn Series User Guide
Appendix B
Media Supplies
To insure maximum printer life and consistent print quality and performance for your individual application, it is recom- mended that only media produced by Zebra be used.
Advantages include:
• Consistent quality and reliability of media products.
• Large range of stocked and standard formats.
• In-house custom format design service.
• Large production capacity which services the needs of many large and small media consumers including major retail chains world wide.
• Media products that meet or exceed industry standards.
For more information go the Zebra website ( www.zebra.com
) and select the Products tab, or refer to the CD included with the printer.
Appendix C
Maintenance Supplies
In addition to using quality media provided by Zebra, it is recommended that the printer be cleaned as prescribed in the maintenance section. The following item is available for this purpose:
• Cleaning Pen (12 pack): p/n 105950-035
84
QLn Series User Guide
Appendix D
Note • The following menus in this Appendix apply only to QLn420 and
QLn Healthcare printers.
SETTINGS Menu
DARKNESS
-49
Set the darkness to the lowest setting that provides good print quality. If you set darkness too high, the label image may print unclearly, bar codes may not scan correctly, or the printhead may wear prematurely.
PRINT SPEED
4.0
Select the speed for printing a label
(given in inches per second). Slower print speeds typically yield better print quality.
Select the type of media that you are using.
MEDIA TYPE
MARK
TEAR OFF
0
If necessary, adjust the position of the media over the tear-off bar after printing.
85
QLn Series User Guide
PRINT WIDTH
576
Specify the width of the labels being used. The default value is the maximum width for the printer based on the printhead’s DPI value.
PRINT MODE
REWIND
Select a print mode that is compatible with your printer options.
LABEL TOP
0
LEFT POSITION
0
REPRINT MODE
OFF
If necessary, shift the print position horizontally on the label. Positive numbers move the left edge of the image toward the center of the label by the number of dots selected, while negative numbers move the left edge of
the image toward the left edge of the label.
When reprint mode is enabled, you can reprint the last label printed either by issuing certain commands or by pressing the DOWN ARROW on the keypad.
86
QLn Series User Guide
LABEL LENGTH MAX
39
LANGUAGE
ENGLISH
Set the maximum label length to a value that is at least 1.0 in. (25,4 mm) greater than the actual label length plus the interlabel gap. If yu set the value to one that is smaller than the label length, the printer assumes that continuous media is loaded, and the printer cannot
calibrate.
If necessary, change the language that the printer displays.
Note • The selections for this parameter are displayed in the actual language to make it easier to find one that you are able to read.
If necessary, shift the print position horizontally on the label. Positive numbers move the left edge of the image toward the center of the label by the number of dots selected, while negative numbers move the left edge of
the image toward the left edge of the label.
When reprint mode is enabled, you can reprint the last label printed either by issuing certain commands or by pressing the LEFT ARROW on the keypad.
87
QLn Series User Guide
TOOLS Menu
HELP FOR
MEDIA
GET HELP
Use scrolling feature to select from a variety of help topics including how to load media, location and removal of battery, and cleaning the printhead.
There are also explanations of various icons including battery, error, latch, media, RCV data, Ethernet, signal,
WLAN, and Bluetooth.
PRINT INFORMATION
SETTINGS
Prints a printer configuration label, sensor profile, barcode information, font information, images, formats, two-key report, and network settings..
LCD CONTRAST
10
Changes the contrast on the printer’s display (i.e. the higher the number, the darker the contrast).
LCD BACKLIGHT
ON
Allows the user to turn the LCD backlight on or off.
88
QLn Series User Guide
BACKLIGHT TIMEOUT
10
Sets the duration of the LCD backlight in seconds.
Select the information shown on the printer’s display when the printer is idle.
IDLE DISPLAY
FW VERSION
POWER UP ACTION
NO MOTION
Set the action for the printer to take during the power-up sequence, i.e. no motion, calibrate, etc.
HEAD CLOSE ACTION
FEED
Set the action for the printer to take when you close the printhead, i.e. feed, calibrate, etc.
LABEL LENGTH CAL
89
QLn Series User Guide
DIAGNOSTIC MODE
ENABLED
Use this diagnostic tool to cause the printer to output the hexadecimal values for all data received by the printer.
ZBI ENABLED?
NO
This menu item indicates if the Zebra
Basic Interpreter (ZBI 2.0TM.) option is enabled on your printer.
90
QLn Series User Guide
NETWORK Menu
ACTIVE PRINT SERVER
NONE
Informs the user of the presence of an active server. Only one print server can be installed at a time, therefore the print server installed is the active print server.
WLAN STATUS
NOT ASSOCIATED
Informs the user if WLAN is associated or not associated.
WLAN IP ADDRESS
0.0.0.0
View, and if necessary, change the printer’s WLAN IP address.
WLAN SUBNET MASK
255.255.255.0
View, and if necessary, change the
WLAN subnet mask.
WLAN GATEWAY
0.0.0.0
View, and if necessary, change the default WLAN gateway.
91
QLn Series User Guide
WLAN IP PROTOCOL
ALL
This parameter tells if the user or the server selects the WLAN IP address.
WLAN MAC ADDRESS
00:19:70:7A:20:44
View the WLAN Media Access Control
(MAC) address of the wireless print server that is installed in the printer.
ESSID
DSF802LESS54
AP MAC ADDRESS
00:05:9A:3C:78:00
The Extended Service Set Identification
(ESSID) is an identifier for your wireless network. This setting, which cannot be modified from the control panel, gives the ESSID for the current wireless configuration.
View the AP MAC address associated with the printer.
CHANNEL
View the network channel.
92
QLn Series User Guide
SIGNAL
0
View, and if necessary, change the printer’s network signal.
WIRED IP ADDRESS
0.0.0.0
View, and if necessary, change the printer’s wired IP address.
WIRED SUBNET MASK
255.255.255.0
View, and if necessary, change the printer’s wired subnet mask.
WIRED GATEWAY
0.0.0.0
View, and if necessary, change the wired gateway setting.
WIRED IP PROTOCOL
ALL
This parameter tells if the user
(permanent) or the server (dynamic) selects the IP address. If a dynamic option is chosen, this parameter tells the method(s) by which the wired or wireless server receives the IP address from the server.
93
QLn Series User Guide
WIRED MAC ADDRESS
00:07:4D:3F:D3:B2
View, and if necessary, change the printer’s network signal.
IP PORT
6101
View, and if necessary, change the printer’s wired IP address.
IP ALT PORT
9100
View, and if necessary, change the printer’s wired subnet mask.
94
QLn Series User Guide
BATTERY Menu
BATTERY ELIMINATOR
INSTALLED
Indicates if a battery eliminator has been installed.
Indicates the current health of the battery, i.e. Good, Past Useful Life, etc.
HEALTH
GOOD
CYCLE COUNT
3
View the current cycle count of the battery.
FIRST USED
7-12-2012
View the date on which the battery was first used in the printer.
SERIAL NUMBER
1509
View the serial number of the battery pack.
95
QLn Series User Guide
TIMEOUT
0 SECONDS
VOLTAGE
8.39
View, and if necessary, change the battery timeout.
View the current voltage level of the battery pack.
WARNING
6.87 (176)
DTR CONTROL
OFF
96
QLn Series User Guide
LANGUAGES Menu
LANGUAGE
ENGLISH
If necessary, change the language that the printer displays.
Note • The selections for this parameter are displayed in the actual languages to make it easier to find one that you are able to read.
COMMAND LANGUAGE
HYBRID_XML_ZPL
ZPL OVERRIDE
DISABLED
Enable this menu item to allow certain
ZPL commands to override the printer’s current settings.
COMMAND CHAR
^ (5E)
Set the format command character to match what is used in your label formats.
CONTROL CHAR
~ (7E)
Set the control prefix character to match what is used in your label formats.
97
QLn Series User Guide
DELIMETER CHAR
, (2E)
Set the delimiter character to match what is used in your label formats.
ZPL MODE
ZPL II
Select the mode that matches what is used in your label formats.
VIRTUAL DEVICE
NONE
98
QLn Series User Guide
SENSORS Menu
MEDIA STATUS
OK
Informs the user of the presence or absence of media in the printer.
LABEL LENGTH CAL
TAKE LABEL
0
Important • This value is set during sensor calibration. Do not change this setting unless you are told to do so by Zebra
Technical Support or by an authorized service technician.
99
QLn Series User Guide
PORTS Menu
BAUD RATE
19200
Select the baud value that matches the one being used by the host computer.
DATA BITS
8
Select the data bits value that matches the one being used by the host computer.
PARITY
NONE
Select the parity value that matches the one being used by the host computer.
STOP BITS
1
Select the stop bits value that matches the one being used by the host computer.
HOST HANDSHAKE
RTS/CTS
Select the handshake protocol that matches the one being used by the host computer.
100
QLn Series User Guide
HALT ON ERROR
YES
Select YES or NO to halt printing upon the occurrence of an error.
101
QLn Series User Guide
BLUETOOTH Menu
BLUETOOTH ADDRESS
NO BLUETOOTH RADIO
View the Bluetooth address for the presence of a BT radio.
View the mode of the BT radio.
MODE
SLAVE
DISCOVERY
ON
View the discovery status, i.e. ON or
OFF.
View the connection status of the BT radio, i.e. YES or NO.
CONNECTED
NO
BT SPEC VERSION
NO RADIO
View the Bluetooth spec version.
102
QLn Series User Guide
MIN SECURITY MODE
1
View, and change if necessary, the minimum security mode of the BT radio.
MFI CAPABILITY
PRESENT
Informs the user of the presence or availability of Made for iPhone (MFi) capability
103
QLn Series User Guide
Appendix E
Serial and PCC Number Locations for QLn Series Printers
PCC Barcode
Serial Number
Barcode
XXX-XXXXXXXX-XX
PLACE BAR CODE HERE
XXXXSYYWWNNNNN
PCC:
S/N:
PLACE BAR CODE HERE
15A 7,4V cove
QLn320
Made
中
QLn320
(Bottom View)
QLn420
(Bottom View)
104
QLn Series User Guide
Serial Number Barcode
PCC Barcode
Appendix F
Battery Disposal
The EPA certified RBRC® Battery Recycling
Seal on the Lithium-Ion (Li-Ion) battery supplied with your printer indicates Zebra Technologies
Corporation is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Li-Ion batteries into the trash or the municipal waste stream, which may be illegal in your area.
Important • When the battery is depleted, insulate the terminals with tape before disposal.
Please call 1-800-8-BATTERY for information on Li-Ion battery recycling and disposal bans/restrictions in your area.
Zebra Technologies Corporation’s involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.
Outside North America, please follow local battery recycling guidelines.
Product Disposal
The majority of this printer’s components are recyclable. Do not dispose of any printer components in unsorted municipal waste. Please dispose of the battery according to your local regulations, and recycle the other printer components accordingto your local standards.
For more information, please see our web site at: http://www.zebra.com/environment.
105
QLn Series User Guide
Appendix G
Alert Messages
The QLn Series printers will display the following alert messages to inform the user of various fault conditions that might occur with the QLn220, QLn320 and QLn420 printers.
Line One (Status)
MEDIA OUT
Line Two (Action)
LOAD MEDIA
Notes
MEDIA COVER OPEN CLOSE MEDIA COVER
MAINTENANCE NEEDED
HEAD MAINTEN. NEEDED
PAPER JAM
PRINTHEAD OVERTEMP
BATTERY DIMINISHED
WARNING - BATTERY
REPLACE BATTERY
BATTERY FAILED
BATTERY LOW
CHARGING TEMP FAULT
CHARGING TEMP FAULT
CHARGING FAULT
DOWNLOADING
DOWNLOAD FAILED
FIRMWARE
LOOKING FOR UPDATES
RETRIEVING FIRMWARE
RETRIEVING NEW FILES
SENDING FEEDBACK
CLEAN PRINTHEAD
PRINTING HALTED
REMOVE MEDIA
PRINTING HALTED
CONSIDER REPLACING
IS PAST USEFUL LIFE
SHUTTING DOWN
REPLACE BATTERY
CHARGE BATTERY
MUST BE 0-40o C
MUST BE 0-40o C
REPLACE BATTERY
FIRMWARE
PLEASE REBOOT
WRITING TO FLASH
PLEASE WAIT. . .
DO NOT POWER OFF!
PLEASE WAIT. . .
PLEASE WAIT. . .
Battery Over Temp
Battery Under Temp
When searching for updates
When retrieving an
application
When downloading files
When sending feedback
MIRRORING COMMANDS
MIRROR PROCESSING
LOSS OF SIGNAL
N/A
FINISHED
MOVE IN RANGE OF AP
SIGNAL RESTORED N/A
For 802.11 models only
For 802.11 models only
Note • Highlighted rows indicate Mirror Alert Messages. The mirror function is only available on units with either an 802.11 radio, Ethernet, or both.
106
QLn Series User Guide
Appendix H
Using Zebra.com
The following examples illustrate the search function on Zebra’s website for finding specific documents and downloads.
Example 1: Find the QLn Series User Guide.
Go to http://www.zebra.com/us/en/support-downloads.html
Type the appropriate printer name in search box.
Type Printer Name (i.e.
QLn320
Click on the link for the desired QLn printer as indicated below.
107
QLn Series User Guide
Click on the “Manuals” tab and select QLn Series User Guide to download the manual.
To download Software, Firmware, or Drivers, click on the appropriate tab listed below and choose the necessary tools.
108
QLn Series User Guide
Appendix I
Product Support
When calling with a specific problem regarding your printer, please have the following information on hand:
• Model number/type (e.g. QLn320)
• Unit serial number (refer to Appendix E)
• Product Configuration Code (PCC) (refer to Appendix E)
In the Americas contact:
Regional Headquarters
Zebra Technologies Corporation
3 Overlook Point
Lincolnshire, Illinois 60069 U.S.A.
T: +1 847 634 6700
Toll Free: +1 866 230 9494
F: +1 847 913 8766
Technical Support
T: +1 877 275 9327
F: +1 847 913 2578
Hardware: [email protected]
Software: [email protected]
Customer Service Dept.
For printers, parts, media, and ribbon, please call your distributor, or contact us.
T: +1 877 275 9327
In Europe, Africa, the Middle East, and India contact:
Regional Headquarters Technical Support Customer Service Dept.
Zebra Technologies Europe Limited
Dukes Meadow
Millboard Road
Bourne End
Buckinghamshire SL8 5XF, UK
T: +44 (0)1628 556000
F: +44 (0)1628 556001
T: +44 (0) 1628 556039
F: +44 (0) 1628 556003
For printers, parts, media, and ribbon, please call your dis tributor, or contact us.
T: +44 (0) 1628 556032
F: +44 (0) 1628 556001
In the Asia Pacific region contact:
Regional Headquarters Technical Support
Zebra Technologies Asia Pacific
Pte. Ltd.
120 Robinson Road
#06-01 Parakou Building
Singapore 068913
T: +65 6858 0722
F: +65 6885 0838
T: +65 6858 0722
F: +65 6885 0838
E: (China) [email protected]
All other areas: [email protected]
Customer Service Dept.
For printers, parts, media, and ribbon, please call your distributor, or contact us.
T: +65 6858 0722
F: +65 6885 0836
E: (China) order-csr@zebra.
com
All other areas: [email protected]
109
QLn Series User Guide
Index
CPCL Font and Bar Code Specifica-
Cradles, Ethernet and Charging 22
A
AC Power Adapter (included in kit p/n
Appendix C, Maintenance Supplies 84
Appendix D, Menus 85
Appendix E, Serial and PCC 104
Appendix F, Battery Disposal 105
Appendix G, Alert Messages 106
Appendix H, Using Zebra.com 107
Appendix I, Product Support 109
D
E
G
General Cleaning Instructions 59
B
Battery pack
Hard Case 56
Healthcare Printers 31,32
I
H
Introduction to the QLn™ Series Print-
L
LCD Control Panel Indicators 63
C
Cable Communication 46
Charger, battery
charging times 20 front panel indicators 20
Configuration Label, sample 68
M
N
Near Field Communication (NFC)
O
110
QLn Series User Guide
P
Preventive Maintenance 59
Printer Status Indicators 63
Printing Method
Programming language
Q
Quad Charger, cycle times 20
S
Shoulder Strap 57
Smart Charger-2 (SC2) Single Battery
Soft Case 56
Specifications, label 72
Specifications, memory and communications 71
Specifications, physical, environmental and electrical 76
Specifications, printing 71
Status Bar Icons 36
T
Troubleshooting 62
Troubleshooting, topics 64
Troubleshooting, tests 66
V
Verify printer is working 44
Z
ZPL Font and Bar Code Specifications
W
WLAN, overview 52
111
QLn Series User Guide
Zebra Technologies Corporation
3 Overlook Point
Lincolnshire, IL 60069 USA
3φ +1 847.634.6700 RU F: +1 847.913.8766
112
QLn Series User Guide
Download
Advertisement
Key features
Rugged exterior for harsh environments
Compact size for easy portability
Wireless connectivity options for easy setup
Long-lasting battery for extended use
User-friendly interface for simple operation
Frequently asked questions
Refer to the Loading Media Procedure section of the User Guide.
You can connect the printer using a cable or wirelessly via Bluetooth or WLAN.
Press the Feed button and hold it for 5 seconds to print a configuration label.
Print a configuration label to verify that the printer is working properly.