Zebra HS3100 User Guide
Zebra HS3100 is a rugged, wireless headset designed for use in loud and noisy environments. It features Bluetooth connectivity, allowing you to pair it with your mobile phone or other Bluetooth-enabled devices. With its over-the-head and behind-the-neck configurations and adjustable headband, it provides a comfortable and secure fit for all-day wear. The HS3100 also boasts a long battery life, lasting up to 13 hours of talk time or 10 days of standby time on a single charge.
Advertisement
Advertisement
HS3100
MN-002774-03EN
Rugged Bluetooth Headset
User Guide
HS3100 RUGGED BLUETOOTH HEADSET
USER GUIDE
MN-002774-03EN
Rev. A
January 2020
ii HS3100 Rugged Bluetooth Headset User Guide
Revision History
Changes to the original guide are listed below:
Change Date
Rev A - 01 09/2016 Initial Release
Rev A - 02 11/2016 Update to remove Mute Microphone
Description
TABLE OF CONTENTS
Chapter 2: Pairing the Headset
Chapter 3: Adjusting the Headset
iv HS3100 Rugged Bluetooth Headset User Guide
Chapter 5: Maintenance and Troubleshooting
Appendix B: Technical Specifications
ABOUT THIS GUIDE
Introduction
This guide provides information about using the HS3100 Rugged Bluetooth Over-the Head (OTH) and
Behind-the-Neck (BTN) Headsets.
NOTE Pictures in this guide are samples and can differ from the actual headset.
Chapter Descriptions
Topics covered in this guide are as follows:
•
Chapter 1, Getting Started , provides an overview, features, and getting started.
•
Chapter 2, Pairing the Headset ,
explains the various ways to pair the headset.
•
Chapter 3, Adjusting the Headset ,
explains how to adjust the headset for proper fit and maximum comfort during use.
•
Chapter 4, Using the Headset , provides basic instructions for using the headset.
•
guidelines, cleaning the headset and troubleshooting solutions for potential problems.
•
, describes the accessories available for the headset.
•
Appendix B, Technical Specifications , provides the technical specifications for the headset.
Notational Conventions
The following conventions are used in this document:
• “tablet” refers to the Zebra tablet.
vi HS3100 Rugged Bluetooth Headset User Guide
• Italics are used to highlight the following:
• Chapters and sections in this guide
• Related documents
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Related Documents
The following document provides more information about the HS3100 Rugged Bluetooth Headset.
• HS3100 Rugged Bluetooth Headset Quick Start Guide , p/n MN-002762-xx - describes how to adjust, use, and maintain the headset and also includes required regulatory information.
For the latest version of this guide and all guides, go to: http://www.zebra.com/support .
Service Information
If you have a problem with your equipment, contact Zebra Global Customer Support for your region. Contact information is available at: http://www.zebra.com/support .
When contacting support, please have the following information available:
• Serial number of the unit
• Model number or product name
• Software type and version number.
Zebra responds to calls by email, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Zebra Customer Support, you may need to return your equipment for servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your Zebra business product from a Zebra business partner, contact that business partner for support.
CHAPTER 1 GETTING STARTED
Headset Overview
The HS3100 Rugged Bluetooth Headset comes in two configurations; Over-the-Head (OTH) and Behind-the-Neck
(BTN) headbands.
NOTE This guide applies to both the OTH and BTN headband models, unless otherwise noted.
The HS3100 headset is ideal for the following applications:
Industries
• Warehousing
• Distribution
• Transportation and Logistics
• Manufacturing
Environments
• Freezers
• Outdoor Yards
• Airports
• Seaports
• Railway Yards
1 - 2 HS3100 Rugged Bluetooth Headset User Guide
Headset Configurations
Table 1-1 Headset Configurations
Model
HS3100-OTH
Configuration
Over-the-Head Headband
Left or Right Side Boom Placement
HS3100-BTN-L Behind-the-Neck Headband
Left Side Boom Placement
Includes
HS3100 Boom Module
OTH Headband
Windscreen
Battery
HS3100 Boom Module
BTN Headband
Windscreen
Battery
Over-the-Head (OTH) Features
Adjustable OTH Headband
T-Bar
Battery
Ear Pad
Flexible Microphone Boom
Multi-
Function
Button with LED
Indicator
NFC Tag
Volume Buttons
Disassembly Knob Microphone with Windscreen
Figure 1-1 HS3100-OTH Bluetooth Headset
Behind-the-Neck (BTN) Features
BTN Headband
Flexible Microphone Boom
Microphone with Windscreen
Left Placement
Ear Pad
Battery
NFC Tag
Multi- Function
Button with
LED Indicator
Volume Buttons
Disassembly Knob
Figure 1-2 HS3100-BTN-L Bluetooth Headset
Getting Started 1 - 3
1 - 4 HS3100 Rugged Bluetooth Headset User Guide
Unpacking
Carefully remove all protective material from the headset and save the shipping container for later storage and shipping.
Verify the following items are in the box:
• Headset:
• Headband Module
• Boom Module
• Battery
• Quick Start Guide
Inspect the equipment for damage. if any equipment is missing or damaged, contact the Zebra Support Center immediately. See
Service Information on page ii-vi
for contact information.
Getting Started 1 - 5
Charging
The headset batteries are charged in a toaster which uses either a one slot cradle or a five slot cradle.
Charging Configurations
Table 1-2 Charging Configurations
Model
Battery Toaster 1 Slot-SE Cradle
Battery Toaster 5 Slot-SE Cradle
Includes
1-Slot Base Cradle
Toaster Cup
PS000084A01 adapter plus CBL-DC-388A1-01 DC cable
5-Slot Base Cradle
Toaster Cup
4 WT/WT Charging Cups
PS000086A01 adapter plus CBL-DC-381A1-01 DC cable
Connect the Charger
NOTE Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page
7-1 .
The 8-Slot Battery Charger charges up to eight spare batteries.
To connect the charger:
Connect one end of the power supply to the charging base and the other end into the outlet.
Figure 1-3 Battery Toaster 1 Slot - SE Cradle and Battery Toaster 5 Slot - SE Cradle
1 - 6 HS3100 Rugged Bluetooth Headset User Guide
Charge the Battery in the Battery Charger
Although the batteries come partially charged, it is recommended to fully charge them before first use. Allow up to three and a half hours for a full charge.
To charge the battery:
Insert the battery into the charger with the contacts facing forward.
Figure 1-4 Charging the Battery in 8-Slot Battery Charger or 8-Slot Battery Charger with 8-Slot-WT6000 Charger
Each battery slot has a battery status indicator displaying the charging status.
Battery Charge LED Status
Table 1-3 Battery Charge LED Status
Mode Description
Charge Fault Fast blinking red
Charging (Healthy)
Charge Complete
(Healthy)
Solid Amber
Solid Green
Insert the Battery in the Headset
To insert the battery:
1.
Insert the battery with the contacts facing outward into the battery slot.
2.
Push the battery into the slot until it is firmly secure.
Getting Started 1 - 7
Figure 1-5 Insert the Battery
1 - 8 HS3100 Rugged Bluetooth Headset User Guide
Power On the Headset
To turn the power on:
1.
Press the Multi-Function button (MFB).
2.
Wait for the headset LED to illuminate blue and flash three times.
The headset is ready to use.
Multi-
Function
Button
Figure 1-6 Power On Headset
MFB Actions and Headset States
Table 1-4 MFB Actions and Headset States
Condition
Headset in Low Power Mode
Action
Press Multi-Function Button for two seconds
Headset in Low Power Mode
Headset is ON or Connected
Press Multi-Function Button for three seconds
Press Multi-Function Button for two seconds
Headset State
Headset goes into Pairing Mode or in
Connected state
Headset goes into Pairing Mode
Headset goes into Low Power Mode
Getting Started 1 - 9
LED Indicator and Headset Status
Table 1-5 LED Indicator and Headset Status
LED Indicator
Three Blue Flashes
Three Red Flashes
Blue and Red Alternate Flashes
Slow Blue Flash
Steady Blue
Slow Two Red Flashes
Power On
Power Off
Pairing Mode
Connected
Not Connected
Low Battery
Headset Status
1 - 10 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 2 PAIRING THE HEADSET
Methods of Pairing the Headset
The headset can be paired with other Bluetooth devices in the following ways:
NFC Tag
Figure 2-1 NFC Pairing
• Standard Bluetooth pairing where the headset is discovered by the host.
• Bypassing device discovery using a multi-modal interface:
• Scan-to-pair - the host gets the headset MAC address through a scan and connects with it.
• Tap-to-pair - with hosts having an NFC reader, the host gets the MAC address through NFC and connects with it.
2 - 2 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 3 ADJUSTING THE
HEADSET
Introduction
This chapter explains how to adjust the headset for the proper fit and maximum comfort during use.
Position the Boom
To position the boom:
Rotate the boom for left side or right side placement.
CAUTION Do not rotate the boom beyond the stop point.
Left Side Boom Placement
Figure 3-1 Position the Boom
Right Side Boom Placement
NOTE Applies to OTH model. The BTN model has only left side boom placement.
3 - 2 HS3100 Rugged Bluetooth Headset User Guide
Adjust the OTH Headband
To adjust the OTH headband:
1.
Squeeze the headband for a tighter fit to the head.
Notice that the headband clicks as it is positioned into place.
2.
3.
Position the ear pad in the center of the ear.
Position the T-Bar above the ear, half way between the top of the ear and the top of the head.
Figure 3-2 Adjust the OTH Headband
Adjusting the Headset 3 - 3
Adjust the Microphone
To adjust the microphone:
Position the microphone icon so that it is facing your mouth.
Microphone Icon
Figure 3-3 Adjust the Microphone
Adjust the Microphone Boom
To adjust the microphone boom:
Place the microphone two finger’s width away from the corner of your mouth, so it is slightly to one side.
Figure 3-4 Adjust the Microphone Boom
3 - 4 HS3100 Rugged Bluetooth Headset User Guide
CHAPTER 4 USING THE HEADSET
Introduction
This chapter provides basic instructions for using the headset.
Adjust the Volume
To adjust the volume:
Press the Volume Up (+) or Volume Down (-) buttons as desired.
Volume UP/DOWN
Buttons
Figure 4-1 Adjust the Volume
Audio Tones
The following transitions and states are associated with the audio tones listed.
4 - 2 HS3100 Rugged Bluetooth Headset User Guide
Table 4-1 Audio Tones
Transition or
State
Start Pairing Two short low tones
Three rising tones Successful
Pairing
Headset
Connected
One tone
Link Lost
Low Battery
Mute
Un-mute
Power Up
Power Down
Two low tones followed by a high tone
Audio Tones
Two short tones every two minutes until shutdown
Two descending tones
Two rising tones
Four tones
Four descending tones
CHAPTER 5 MAINTENANCE AND
TROUBLESHOOTING
Introduction
This chapter includes instructions on replacing parts and accessories, safety and battery guidelines, cleaning and storing the headset and provides troubleshooting solutions for potential problems during operation.
Maintaining the HS3100 Headset
For proper maintenance and maximum operating use and comfort, various parts and accessories can be replaced.
Replace T-Bar
To replace the T-Bar:
1.
Pull and remove the T-Bar off the headband.
Figure 5-1 Remove T-Bar
5 - 2 HS3100 Rugged Bluetooth Headset User Guide
2.
Align the T-Bar slot with the end of the headband and push the replacement T-Bar on the headband until firmly secured.
Figure 5-2 Replace T-Bar
NOTE Applies to OTH model.
Replace Headband
To replace the headband:
1.
Loosen the screw.
Figure 5-3 Loosen Screw
2.
Disassemble the headset to replace the headband.
Maintenance and Troubleshooting 5 - 3
Figure 5-4 Disassemble headset
Replace Ear Pad
To replace the ear pad:
1.
Firmly grip and pull the ear pad and inner casing.
Figure 5-5 Remove Ear Pad
5 - 4 HS3100 Rugged Bluetooth Headset User Guide
2.
Align and snap the new ear pad into position.
Figure 5-6 Replace Ear Pad
Remove the Battery
To remove the battery:
Firmly grip the outer battery casing, and pull tightly.
Maintenance and Troubleshooting 5 - 5
Figure 5-7 Remove the battery
Replace Windscreen
To replace the windscreen:
1.
Pull and remove the windscreen off the microphone.
Figure 5-8 Remove Windscreen
2.
Align and slide the replacement windscreen over the microphone.
Figure 5-9 Replace Windscreen
5 - 6 HS3100 Rugged Bluetooth Headset User Guide
Maintain Headset in a Freezer Environment
1.
2.
When working in a freezer environment, replace the windscreen every four hours, or when it is wet or frozen.
If the microphone stops working, it could be wet. Remove the windscreen, shake the microphone boom, and place a dry windscreen on the microphone boom. Be careful not to squeeze the wet windscreen while it is on the microphone boom.
Safety Guidelines
General Safety Guidelines
• Please read the User Guide carefully and completely before using the product.
• Always keep the product dry and do not expose it to extreme temperatures.
• Use the product with care and store it in a clean, just-free environment.
• Only use the power supply units intended for use with the product.
Battery Safety Guidelines
CAUTION Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
• The area in which the HS3100 headsets are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the headset is charged in a non-commercial environment.
• Do not use incompatible batteries and chargers. If you have any questions about the compatibility of a battery or a charger, contact Zebra Support. See
Service Information on page ii-vi for contact information.
• Do not crush, puncture, or place a high degree of pressure on the battery.
• Follow battery usage, storage, and charging guidelines.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the headset battery, the battery and charger temperatures must be between 32ºF and +113ºF (0ºC and +45ºC).
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
Maintenance and Troubleshooting 5 - 7
• Seek medical advice immediately if a battery has been swallowed.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, call Customer Support to arrange for inspection. See
Service Information on page ii-vi for contact information.
Cleaning the HS3100 Headset
The headset does not require any user preventative maintenance other than cleaning of the keys, microphone and speaker area.
To maintain the headset, it is suggested to adhere to the following guidelines:
• Do not expose the headset to harsh chemicals or cleaning agents.
• Do not immerse the headset in water.
• If the headset becomes dirty, wipe it with a soft damp cloth. Do not use soap, cleaning fluids or chemicals.
• Keep dust, dirt and debris out of the headset battery slot and the battery charger slots.
• When handling the headset battery, keep the battery contacts free of dirt, grease, oil and other substances that can affect the battery from making proper contact with the headset or charger.
All the surfaces that touch a worker’s skin or hair, or that a worker breathes into, are easily replaced in the field.
5 - 8 HS3100 Rugged Bluetooth Headset User Guide
Troubleshooting
This section provides troubleshooting solutions for potential problems during HS3100 operations.
Table 5-1 Troubleshooting
Problem
Operating
Headset does not turn on
No LED’s light on charger when battery is inserted
Solution
- Verify the battery is fully inserted in the headset.
- Verify the battery is charged.
Pairing
Headset does not pair
Headset appears to be paired but cannot communicate with the intended Bluetooth device
- Verify headset is off when beginning the pairing process.
- Verify intended Bluetooth device is on.
- Verify headset is within twelve inches of intended
Bluetooth device.
- Select HS3100 on the Bluetooth device search menu.
The headset may be connected with an incompatible
Bluetooth device.
1. Verify the intended Bluetooth device is within twelve inches of the headset.
2. Verify all other non-intended Bluetooth devices are six feet away from the headset.
3. Turn off the headset and start the pairing process again.
Charging Battery
Battery does not sit properly in the charging slot - Rotate battery and re-insert into the charging slot. The battery cannot be inserted into the cup in the wrong direction.
- Check the power cable connection to the charger.
- The battery may be faulty. Replace the battery.
APPENDIX A ACCESSORIES
This appendix provides information about the HS3100-OTH and HS3100-BTN-L accessories.
Parts and Accessories
The following table lists the part numbers for the headsets and available accessories.
Table A-1 Parts and Accessories
Part/Accessory
Headset and Modules
HS3100 Bluetooth Headset - OTH
Part Number
HS3100-OTH
HS3100 Bluetooth Headset - BTN - Left HS3100-BTN-L
HS3100 Boom Module
HSX100 BTN Headband Left Module
HSX100 OTH Headband Module
HS3100-BOOM-01
HSX100-BTN-L-HB-01
HSX100-OTH-HB-01
Description
HS3100 Rugged Bluetooth Headset
(Over-the-Head Headband)
(Includes HS3100 Boom Module and
HSX100 OTH Headband Module)
HS3100 Rugged Bluetooth Headset
(Behind-the-Neck Headband Left)
(Includes HS3100 Boom Module and
HSX100 BTN Headband Module Left)
HS3100 Boom Module
(Includes Microphone Boom, Battery, and Windscreen)
HSX100 BTN Headband Left Module
(Includes BTN Headband and Ear Pad)
HSX100 OTH Headband Module
(Includes OTH Headband, Ear Pad, and T-Bar with Pad)
Chargers
8-Slot-Battery Charger SAC-HS3100-B8-01 Charges up to eight HS3100 batteries
A - 2 HS3100 Rugged Bluetooth Headset User Guide
Table A-1 Parts and Accessories (Continued)
Part/Accessory
8-Slot-Battery Charger &
8-Slot-WT6000 Charger
Part Number
SAC-HS3100-B8W8-01
Cables
USB Cable CBL-HS3100-CUC1-01
Replacement Parts
8-Slot-Battery Charger Spare Cup A9310272-003
Single Battery
Battery Pack of 8
BTRY-HS3100-HS1-01
BTRY-HS3100-HS1-08
Over-the-Head Headband Pack of 10 KT-HSX100-OTH1-10
Behind-the-Neck Headband Left Pack of 10
KT-HSX100-BTNL1-10
HSX100 Headset Foam Ear Pad Pack of 20
HSX100 Headset Leatherette Ear Pad
Pack of 20
HSX100 Headset Series Microphone
Windscreen Pack of 50
T-Bar with Pad Pack of 20
KT-HSX100-EPF1-20
KT-HSX100-EPL1-20
KT-HSX100-MWS1-50
KT-HSX100-TBP1-20
Description
Charges up to eight HS3100 batteries and up to eight WT6000 devices
USB Type-A 36" (0.9M) Charging and communication cable
Mounts on the 8-Slot Battery Charger or the 8-slot Battery Charger & 8-Slot
WT6000 Charger
Replacement HS3100 battery
Replacement HS3100 battery (8-pack)
Replacement HS3100-OTH headbands
(10-pack)
(Includes Headband, T-Bar and Ear
Pad)
Replacement HS3100-BTN-L headbands (10-pack)
(Includes Headband and Ear Pad)
Replacement foam ear pad (20-pack)
Replacement leatherette ear pad
(20-pack)
Replacement microphone windscreen
(50-pack)
Replacement T-Bar with pad (20-pack)
APPENDIX B TECHNICAL
SPECIFICATIONS
This section provides technical specifications for the HS3100 Bluetooth Headset and charging cradles
HS3100 Technical Specifications
Table B-1 HS3100 Bluetooth Headset Technical Specifications
Item Description
Physical Characteristics
Weight 4 oz./115 g (with battery)
Wearing Styles Over-the-head headband
Behind-the-neck headband
Headband, battery, ear pad, windscreen, T-bar Field
Replaceable
Parts
Power
Performance Characteristics
Speech-Directed
Applications
Can work with all Zebra devices running speech recognition and text-to-speech engines for speech-directed applications
Audio
Li-ion 220 mAh, 3.7V with up to 15 hours of continuous speech use on a single charge using a battery with ≤ 100 charge/discharge cycles
High performance sealed noise canceling microphone with noise immunity greater than 10 dB for high noise environments
50 Hz to 8 kHz Send Frequency
Response
Microphone
Sensitivity
-53 dB @ 1 kHz, 1 Pa
B - 2 HS3100 Rugged Bluetooth Headset User Guide
Table B-1 HS3100 Bluetooth Headset Technical Specifications (Continued)
Item Description
Receive
Frequency
Response
300 Hz to 6 kHz
Speaker
Sensitivity
89 dB SPL with 1.0 Vrms @ 1 kHz
Bluetooth
NFC
Bluetooth Class II, v 3.0; Bluetooth Hands-free Profile (HFP 1.6)
NFC tag used for Tap-to-Pair
User Environment
Zebra Mobile
Computers
Compatibility
Visit www.zebra.com/hsheadsets for the most current list of compatible mobile computers.
User Interfaces LED: Bi-color LED for headset status
Buttons: Three functional buttons
-30°C (-22°F) to +50°C (+122°F) Operating
Temperature
Storage
Temperature
-40°C (-40°F) to +60°C (+140°F) incl. battery
-40°C (-40°F) to +70°C (+158°F) excl. battery
Sealing Rating
Humidity
Drop Rating
Tumble Rating
IEC 60529: IP67
5% to 95% non-condensing
6 ft./1.8 m drop to concrete (36 drops, over operating temperature range)
1,000 tumbles @ 0.5 m (room temperature)
Vibration Since 5-2000Hz, 4g peak, 1 hour per axis; Random 20-2000Hz, 6g RMS or 0.04g2/Hz, 1 hour per axis
+/-20kV air discharge, +/-10kV contact discharge, +/-10kVdc indirect discharge Electrostatic
Discharge (ESD)
Software Compatibility
Software TekSpeech Pro 4, Android EMDK
The HS3100 is optimized for real-time two-way speech applications and uses the BT Hands Free Profile. A host connected to HS3100 can remotely control audio volume and microphone gain of the headset.
The HS3100 sends the host its battery information (Serial Number, State of Charge and State of Health), the power state (main or backup battery) and headset information (Serial Number, HW and FW version, and its capabilities).
8-Slot Battery Charger Technical Specifications
Table B-2 8-Slot Battery Charger Technical Specifications
Item Description
Dimensions Height: 74.1 mm
Width: 97.8 mm
Depth: 134.7 mm
Weight
Input Voltage
439.8 g
12 V
5.82 Watt (Full load), 0.18 Watt (No load) Power
Consumption
Operating
Temperature
Storage
Temperature
Charging
Temperature
0° C (32° F) to 45° C (113° F)
-40° C (-40° F) to 70° C (158° F)
0° C (32° F) to 40° C (104° F)
Humidity
Drop
Electrostatic
Discharge (ESD)
10% to 95% RH
30 inches
+/- 15 k V air (Certificate)
+/- 8 k V Contact and Indirect (Certificate)
Technical Specifications B - 3
B - 4 HS3100 Rugged Bluetooth Headset User Guide
8-Slot-Battery Charger & 8-Slot-WT6000 Charger Technical Specifications
Table B-3 8-Slot Battery Charger & 8-Slot-WT6000 Charger Technical Specifications
Item Description
Dimensions Height: 87.1 mm
Width: 134.7 mm
Depth: 488.4 mm
Weight
Input Voltage
2.2 kg
12 V
60 Watt (Full load), 0.18 Watt (No load) Power
Consumption
Operating
Temperature
Storage
Temperature
Charging
Temperature
0° C (32° F) to 45° C (113° F)
-40° C (-40° F) to 70° C (158° F)
0° C (32° F) to 40° C (104° F)
Humidity
Drop
Electrostatic
Discharge (ESD)
10% to 95% RH
30 inches
+/- 15 k V air (Certificate)
+/- 8 k V Contact and Indirect (Certificate)
INDEX
A
adjust the OTH headband . . . . . . . . . . . . . . . . . . . . . 3-2
audio tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
B
behind-the-neck features . . . . . . . . . . . . . . . . . . . . . . 1-3
bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
buttons/LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
C
charge the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
charger configurations . . . . . . . . . . . . . . . . . . . . . . . . 1-5
clean the headset . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
connect the charger . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
conventions
notational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii-v
H
headset configurations . . . . . . . . . . . . . . . . . . . . . . . 1-2
HS3100 technical specifications . . . . . . . . . . . . . . . . B-1
I
information, service . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
insert the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
O
over-the-head features . . . . . . . . . . . . . . . . . . . . . . . 1-3
overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
P
pairing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . A-1
position the boom . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
power on headset . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
R
related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
remove battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
replace ear pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
replace headband . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
replace t-bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
replace windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
S
safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
T
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
V
volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Index - 2 HS3100 Rugged Bluetooth Headset User Guide
Zebra Technologies Corporation, Inc.
3 Overlook Point
Lincolnshire, IL 60069, U.S.A.
http://www.zebra.com
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
MN-002774-03EN Revision A - January 2020
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
