JUNG 244EX Rotary dimmer insert 60 – 400 W Operating instructions
Add to My manuals5 Pages
JUNG 244EX:
The JUNG 244EX is a rotary dimmer designed for incandescent and HV halogen lamps. It features a phase cut-on dimming principle, soft locking on operation, and short-circuit protection through a fine-wire fuse. The dimmer is suitable for mixed operation, allowing you to connect both incandescent and halogen lamps up to the specified output. It can be installed in an appliance box according to DIN 49073.
Here are some of the key features and use cases of the JUNG 244EX:
- Dimming: The dimmer allows you to adjust the brightness of your connected lamps from minimum to maximum brightness.
advertisement
![JUNG 244EX Rotary dimmer insert 60 – 400 W Operating instructions | Manualzz JUNG 244EX Rotary dimmer insert 60 – 400 W Operating instructions | Manualzz](http://s3.manualzz.com/store/data/054085743_1-bd48f37b3c95bd4e568713f234833810-360x466.png)
Light Management
Rotary dimmer for incandescent lamps
Rotary dimmer for incandescent lamps
Art.-No.: 244 EX
Operationsmanual
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and other hazards.
Always disconnect before carrying out work on the devise or load. At the same time, take into account all circuit breakers that supply dangerous voltage to the device or load.
The device is not suitable for disconnection from supply voltage.
Do not connect electronic lamps, e.g. switchable or dimmable energy-saving lamps or
LED lamps. Otherwise the possibility of a device defect cannot be ruled out.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
picture 1: Device components
(1) Dimmer
(2) Frame
(3) Central plate
(4) Control button
(5) Fuse holder
(6) Screw terminals
3 Function
Intended purpose
- Switching and dimming incandescent lamps and HV halogen lamps
- Suitable for mixed operation up to the specified output (see section Technical data)
- Installation in appliance box acc. to DIN 49073 i No operation with transformers.
32542213
J:0082542213
1/5 19.08.2010
Light Management
Rotary dimmer for incandescent lamps
Product characteristics
- Phase cut-on dimming principle
- Soft locking on operation
- Short-circuit protection through fine-wire fuse
- Changeover switching possible in combination with changeover switch
- Operation on 60 Hz mains possible i Flickering of the connected lamps due to undershoot of the specified minimum load or through centralised pulses from the power stations and soft humming of the device due to the radio interference suppressor. These are not device faults.
4 Operation
Switch light o Press the control button.
Adjust the brightness
Light is switched on. o Turn the control button in the clockwise direction.
The light gets brighter up to maximum brightness. o Turn the control button in the anti-clockwise direction.
Light gets darker to minimum brightness.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the corresponding circuit breakers. Cover up live parts in the working environment.
Connecting and mounting the dimmer picture 2: Connection diagram o Connect the dimmer (1) according to the connection diagram (picture 2).
32542213
J:0082542213
2/5 19.08.2010
Light Management
Rotary dimmer for incandescent lamps o Mount the dimmer in the accessory socket. o Attach the frame and the central plate. o Attach the control button.
Connection in changeover switch i No changeover switch possible with two dimmers. picture 3: Changeover switch o Connect the dimmer (1) and the changeover switch (7) according to the connection diagram (picture 3).
5.2 Commissioning
Setting basic brightness in operation on 60 Hz mains
The basic brightness is set ex works for operation on 50 Hz mains. If the dimmer is used on
60 Hz mains, the basic brightness must be reset by an electrically skilled person.
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Use only insulated tools to set the basic brightness. Cover up live parts in the working environment.
32542213
J:0082542213
3/5 19.08.2010
Light Management
Rotary dimmer for incandescent lamps picture 4: Adjusting basic brightness
(1) Dimmer
(8) Basic brightness setter o Switch off the mains voltage. o Connect dimmer as described above, but do not install in the appliance box yet. When doing this, ensure insulation of the cables in accordance with regulations. o Switch on mains voltage. o Press the rotary axle to switch on the lighting and turn it left to the minimum brightness. o Adjust basic brightness by turning the lateral adjuster (8) (picture 4). i According to EN 60669-2-1 (01.2000), lamp brightness should be detectable over the whole load area, with darkness at – 10 % rated voltage. o Switch off the mains voltage. o Mount the dimmer in the accessory socket. o Mount the frame and the central plate. o Attach the control button. o Switch on mains voltage again.
6 Appendix
6.1 Technical data
Rated voltage
Mains frequency
Ambient temperature
Connected load at 25 °C
Incandescent lamps
HV halogen lamps
Power reduction per 5°C in excess of 25°C when installed in wooden or dry construction walls when installed in multiple combinations
Connection
Single stranded
Power boosters
Fine-wire fuse
AC 230 / 240 V ~
50 / 60 Hz
+5 ... +25 °C
60 ... 400 W
60 ... 400 W
-10 %
-15 %
-20 % max. 4 mm² none
D 1.6 H 250
32542213
J:0082542213
4/5 19.08.2010
Light Management
Rotary dimmer for incandescent lamps
The symbols used to label the dimmer load shows the load type that can be connected to a dimmer and the electric behaviour of a load: R = ohmic
6.2 Troubleshooting
Device switches load off and remains switched off.
Short-circuit protection has tripped.
Check the fine-wire fuse
Replace the fine-wire fuse Use only original fuses (see chapter 6.1. Technical data).
6.3 Warranty
We reserve the right to make technical and formal changes to the product in the interest of technical progress.
We provide a warranty as provided for by law.
Please send the unit postage-free with a description of the defect to our central customer service office:
ALBRECHT JUNG GMBH & CO. KG
Service Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +49 (0) 23 55 . 80 65 51
Telefax: +49 (0) 23 55 . 80 61 89 [email protected]
General equipment
Service-Line: +49 (0) 23 55 . 80 65 55
Telefax: +49 (0) 23 55 . 80 62 55 [email protected]
KNX equipment
Service-Line: +49 (0) 23 55 . 80 65 56
Telefax: +49 (0) 23 55 . 80 62 55 [email protected]
The Œ symbol is a free trade symbol, which is solely intended for the authorities and does not guarantee any properties.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
D-58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-1 89
E-mail: [email protected]
Internet: www.jung.de
www.jung-katalog.de
32542213
J:0082542213
5/5 19.08.2010
advertisement