SnapScan 5000

-Patent pending-

User Manual

Version 1.15

November 2010

Declaration of Conformity

We declare JOBO International GmbH,

Eintrachtstr. 14,

D-51645 Gummersbach that the “SnapScan 5000” complies with the following directives:

EN 55022:2006+A1:2007 Radio interference suppression (ITE).

Limits and methods of measurement

EN 55024:1998/A2:2003 EMC Immunity to Radiated Fields (ITE)

EN61000-3-2:2006 Elektromagnetic Compatibility (EMC-Part 3-2)

EN61000-3-3:2008 Elektromagnetic Compatibility (EMC-Part 3-3)

This declaration of EC conformity shall become null and void when the assembly is subjected to any modification that has not met with our approval.

Gummersbach, 05. September 2010 Johannes Bockemühl

Geschäftsführer

-2-

Index

1

 

Unpack SnapScan5000

....................................................4

 

2   Install film into the film holder ....................................6

 

3

 

Quick Start

....................................................................9

 

4   Operation Guide .........................................................14

 

5   Capture......................................................................14

 

6   Film Type...................................................................27

 

7   Setting Mode..............................................................30

 

8

 

Specification

...............................................................33

 

9

 

Waste Management

......................................................34

 

10

 

Service

.......................................................................35

 

-3-

1 Unpack SnapScan5000

JOBO SnapScan 5000 Negative Holder User Manual

USB power core USB/Video cable Roll Film Holder Clean brush

2 x Rapid slide feeder

-4-

Note

 We strongly suggest using a clean, dry, non-alcohol cotton swab to clean the glass surface periodically to produce a clear image during operation.

 Clean dust from Film Scanner back light, to use the clean brush to wipe the dust.



Dust or dirt from the negative, slide films and cover trays may affect the scanned image quality, please make sure the materials are cleaned before inserting into the scanner.

 Please find recommend, processional purger from photo store to clean the dust on films if any to avoid damaging the only one copy of old films.

-5-

2

2.1

Install

 

film

 

into

 

the

 

film

 

holder

 

Insert slides into the rapid slide feeder

1. Put a stack of slides into the feeder

Film   Slot  

2.2

After the slides are placed into the holder and the holder is placed into the slot of the scanner (refer to „Quick Start“) the slides can be slide into the scanner by moving the holder backward and forward.

The slides are positioned automatically inside the scanner.

Install the Negative Film into holder

1. Open the film holder as illustrated

2. Install film into negative film slot 3. Close the film holder

-6-

2.3

Install the Roll Film into holder:

1. Take out the roll film holder from package

2. Insert roll film into film slot 3. Pull out the roll film in another side

-7-

Note

 To avoid mirror image, follow the serial numbers (from left to right) on top of film when install negative film into holder

Figure   1  

 If the image is upside down [see fig.2], the image can be corrected by Flip function in Button of device before capture.

Figure   2

-8-

3 Quick Start

Right/+   button  

Left/ ‐   button

SD   card   Slot  

Power   button

USB   port  

TV   out   jack

-9-

Power   status   LED  

OK   button  

Film   Slot  

1. Put Film onto the film cartridge

2. Insert the film cartridge into JOBO SnapScan 5000

-10-

3. Connect power USB cable to SnapScan 5000

4. Turn on Device by pressing the power button

-11-

5. Press OK button to capture the image

6. Follow the menu on display for scanning

-12-

7. After finished the capture, take out the SD card which stored capture images

8. Or read picture from PC by MSDC mode

-13-

4

4.1

Operation

 

Guide

 

Home: Main menu

Capture

Playback

Film   Type

USB   mode Setting

•

Capture: capture mode (default)

•

Playback: playback mode

•

Film Type: define the film type which loaded in cartridge

•

USB mode: MSDC (Mass Storage Device Class) mode

•

Setting: TV out and format option

5 Capture

 

Capture  

After welcome page, above menu will remains for 5 sec. User can press up/down button for desired menu. Or system will auto enter Capture mode if there is no action during this 5 second period.

-14-

5.1

Capture: <Up>/<Down> (Button)

Flip   button   mirror  

Mirror   button

• press <Mirror> Button to mirror image from right to left

•

Press <Down> button to upside down image

-15-

5.3

5.2

Capture mode

Live   view   indicator  

(flashing   at   0.5sec

  rate)  

Once enter capture mode, there will be a red indicator on left top corner to indicate it is in live view mode. When the film cartridge is inserted into the scanner slot, the image always shows the positive image according to previous defined Film Type (after power on. the Film Type is default to negative film). Reconfirm the film position through the display before press OK button.

Capture: Edit Menu

Save  

Selected   image

Rotate   +90  

Rotate  ‐ 90  

Cancel Home

•

Save: save captured image

•

Rotate +90: continue rotate +90 degrees

•

Rotate -90: continue rotate -90 degrees

(this is for adjusting the user who took the portrait picture)

•

Cancel: cancel any editing with this image

•

Home: Back to main menu

-16-

5.4

Live View -> Capture/Edit Menu

Live View Capture/Edit Menu

OK

OK

Once press OK button in live view, the edit menu will be appeared. When user press OK button again, the current image will be saved into SD card. The display will return to live view again.

5.5

Capture: Save

Save  

Once user press OK button on top of SnapScan 5000, preview (live view) image will be selected and shown on the TFT which will take between 3-4 second with 4 icons shown on the left side of the screen. Save icon will be highlighted for user to confirm the saving by OK button. After the above step, display goes back to live view mode

(preview).

-17-

5.6

Capture: Rotate +/-90 degrees

OK

User can apply the up/down button for further editing (rotate +90/-90). Once user confirm rotate +90 degrees, they can press the OK button, the image will be rotate +90 degrees and cursor will remain at Save. Press OK button again will save the rotated image to SD card and screen will return to live view. For continuously rotate +90 degrees, move cursor to rotate again and press OK.

5.7

Capture: Cancel

Playback  

/captured   image

Or select Cancel and press OK button to cancel any of the editing step with present selected image and SnapScan 5000 goes to live view mode (nothing will be saved onto the SD card).

-18-

5.8

Capture: Home

OK

Go back to main menu, press OK button when select Home icon.

5.9

Exit from Edit mode back to Capture mode (Live View)

Next   image   in   film   cartridge

Once User presses OK button for save or cancel option, display will return to capture mode/live view. Then, user can move the film cartridge to next target film to capture.

-19-

5.10

Memory full

OK

Once the internal memory or SD card is full, user can see a SD card full once press OK button. User has to down load the images to PC or replace another SD card for continue capture.

5.11

SD card locked

SD   card   locked    indicator

If the SD was locked, once press the OK button, a SD Card locked icon displays on screen.

Please do slide the switch of SD card to unlock before insert into device.

-20-

5.12

SD card error

SD   card   error indicator

  

If scanner cannot detect SD card in good condition, a warning icon with question mark will be shown on display. Please try to format the SD card or replace another proper SD card for continue further operation. (Refer to Setting section)

-21-

5.13

Playback

Playback

Press Down button to Playback mode when power on SnapScan 5000 or access the main menu by Home icon if during operation. Press OK button to confirm the selection.

5.14

Playback: Auto Slide Show

Slide show mode

Once user enter playback mode (default to slide show), 2.4 TFT will auto display all images stored in SD card with 2 seconds interval from previous captured image. User can also stop the slide show mode by press OK button.

-22-

5.15

Playback: Edit Menu

Press 2x OK during playback

Rotate   +90

Rotate  ‐ 90

Mirror

Flip

•

Rotate +90: captured image rotate +90 degrees

•

Rotate -90: captured image rotate -90 degrees

•

Mirror: change image left to right

•

Flip: upside down image

•

Exit: returns to Slide show

•

Delete: delete this picture stored in SD card

•

Save: save the modified image onto SD card

•

Home: returns to main menu

Exit

Delete

Save

Hom

5.16

Playback: Slide mode -> Edit mode

User can interrupt (stop) the slide show mode to stand alone playback mode (single picture playback) by press OK button. (Pause slide show) Then user is able to scroll each picture by up/down button. Once user select the picture stored in SD card which intended to be modified, then use OK button again to bring out the edit mode for

-23-

modification

5.17

Slide Show -> Single picture -> Edit mode

Pausse

OK OK

Single   picture   mode   to  

Use   Up/Down   button   scroll   picture   to   be   modified

5.18

Playback: Rotate/Mirror/Flip/Save

OK

If user wants to Rotate +90 degrees by OK button, the image will be rotate +90 degrees and cursor will remains at Save. Press OK button again to save modified result and next picture will be shown (N+1). For continuously Rotate +90 degrees, move cursor to

Rotate again and press OK. (Same for Rotate -90, Mirror, and Flip function)

-24-

5.19

Playback: Exit

OK

Once user select the EXIT function in edit menu, the display will go back to slide show starting with the current picture in internal memory or SD card without saving any change of present picture

5.20

Playback: Delete

OK

Delete will delete the present selected picture and next picture will be shown (N+1).

Cursor goes to Exit icon. If user intend to process continuously delete, just move to delete icon again and press OK to confirm.

-25-

5.21

Playback: Home

OK

Go back to main menu, press OK button when select Home icon

5.22

Playback: No Picture

OK

If there’s no picture inside internal memory or SD card when enter playback mode, a No picture symbol will show on display.

-26-

6 Film

 

Type

 

Film Type

Change film type definition by enter Film Type menu when power on SnapScan 5000 or access the main menu by Home icon if during operation. Press down button for Film

Type and press OK to confirm.

6.1

Film Type: Select Film Type

Color   Negative   film

B&W  

Slide   film

Negative

•

Negative film: select Negative film when cartridge loaded with negative film

•

Slide: select Slide type when load slide in holder

•

B&W film: select B&W when cartridge loaded with Black&White negative film

-27-

6.2

Film Type: Example

Color   Negative   film

B&W  

Negative   film

Slide

Loaded   

Into   

Cartridge

-28-

6.3

USB Mode

USB   mode  

After finished capture, user can download the stored images from internal memory or SD card to PC by selecting USB mode. Press OK button when connect USB cable to PC,

SnapScan 5000 becomes a mass storage device. User can review or edit images once PC detected the external storage device. Or just take out the SD card from device into PC to read the images directly.

6.4

USB Mode: Status

Once user select USB mode, SnapScan 5000 becomes a mass storage device and then a status icon shows on display, then user can find an external USB disk device from my computer and review the images in internal memory or SD card with PC.

-29-

7 Setting

 

Mode.

 

Setting   mode

The setting mode covers TV out and format option. User can connect the device to TV and finish the operation with TV display. Moreover, the scanned images can be playback on TV display to share with family.

If the SD card was formatted by the other devices and not readable by scanner, user can apply the format function in scanner to correct required format.

7.1

Setting Mode

TV   out

Format

Exit

•

TV out: select NTSC or PAL according to required interface

•

Format: format internal memory or SD card

•

Exit: returns to main menu

-30-

7.2

Setting: TV out

OK

When user want to switch the display from on device LCD to TV display, user can connect device to TV and select PAL or NTSC as required in TV out menu by OK button.

Then, the TV display will show the same option for scanning operation. Or directly enter playback mode to slide show captured images on TV.

7.3

Setting: Format

OK

If the internal memory or SD card requires format by scanner, user can enter format mode by press OK button. The default setting will be cancel format. User can press

OK button again to cancel the format or select confirm icon to confirm format the memory.

-31-

Note

If there’s no SD card inside device, the internal memory will be formatted once process

Format. Instead, if SD card is inserted in device, SD card will be formatted.

Good bye page

-32-

8 Specification

Image Sensor: 9 mega CMOS sensor

LCD:

Internal memory:

Focus Range:

Exposure Control:

Color Balance:

Scan Quality:

Data Conversion:

2.4’’ Color TFT LCD (2.5” optional)

24MB NAND Flash (for saving images)

Fixed focus

6 levels of control

6 levels of control

2,400 dpi 3,600 interpolated

10 bits per color channel

Scan Method:

Light Source:

Interface:

Single pass

Back light (3 white LEDs)

USB 2.0, TV-out (video 3.5mm jack)

USB Configuration: Mass Storage Device Class/MSDC

Power: 5V adapter, or USB power

Dimensions: 82x86x152mm

Weight: 0.41kg

External memory: SD/MMC compatible

-33-

9 Waste Management

9.1

Packaging

To avoid damage and pollution of the product the Photoframe will be delivered within a packaging. Zum Schutz vor Schäden wird das Gerät in einer Transportverpackung ausgeliefert. These Packaging can be recycled.

9.2

Disposal of WEEE (Waste Electrical and Electronic Equipment)

Devices marked with the WEEE logo are subject to the European Community

Directive 2002/96/EC.

Waste Electrical and Electronic Equipment must be separated from household rubbish and disposed at sites that collect WEEE.

By orderly disposing WEEE you will avoid damage caused to the environment.

Service: To guarantee a product always at the best standard this manual as well as the product itself are subject to alterations.

-34-

10 Service

Within the uncommon situation of failures further Information for Service can found at the Homepage www.jobo.com

-35-