advertisement
Combo
Scanner
II
Combo Scanner II ‐ 5M ‐ 3.0
User Manual
Version 1.02
January 2011
Index
I.
Unpack Combo Scanner II…………………................................2
II.
Install film into the film holder…………..……………………........3
III.
Quick Start.........................................................................6
IV.
Operation Guide..............................................................14
V.
Specification....................................................................33
‐ 1 ‐
I.
Unpack Combo Scanner II
Backlight Holder
Slide Film Holder
Business Card Fixture
Combo Scanner II Negative Film Holder Photo/Business Card Holder
USB/Video Cable
Note
Power Core & Cable Clean Brush User Manual
We strongly suggest using a clean, dry, non-alcohol cotton swab to clean the glass surface on the back-light holder and the business card fixture periodically to produce a clear image.
Make sure all negative films, slide films, cover trays and photos are free of dust and dirt before inserting into the Combo Scanner as this may affect the image quality when scanning.
When cleaning films, please use a professionally recommended purger from a photo store to avoid damaging old or precious films.
‐ 2 ‐
II.
Install film into the film holder
●
Install slide film into the holder entitled “Slides Only”
1.
Open the slide holder as illustrated
2.
Place slide in recessed slot in 3.
Close the slide holder
● Install Negative Film into holder entitled “Negative Film Only”
1.
Open the film holder as illustrated
2.
Install film into negative film slot 3.
Close the film holder
‐ 3 ‐
Note
To avoid mirror image, follow the serial numbers (from left to right) on top of film when install negative film into holder
Figure 2.1
If the image is upside down [Figure 2.2], the image can be corrected by pressing
Down/Flip button before capturing [Figure 2.3].
Alternative, enter the playback mode and press Mode button to select Flip function [Figure 2.4]
Figure 2.2
‐ 4 ‐
Down/Flip button
(Flip hard key)
Flip
● Press hard key on top of device in live view [Figure 2.3]
Playback button
● Press Playback button Mode/Setting to select Flip function (Refer to P.25)
[Figure 2.4]
‐ 5 ‐
III.
Quick Start
Up/Mirror
Left/EV
Right/Color
Down/Flip
Photo/Business
Card slot
Power button
Power status LED
Playback
Mode/Setting
OK/Capture
SD card slot
Film/Slide slot
Slot for Backlight holder
‐ 6 ‐
Power core port
USB Port (For data only)
TV out jack
How to use Combo Scanner II
Scanning Film/Slide
1.
Put Film into Film holder, and Insert the film holder into the right side of the unit.
2.
Insert the back light holder at the rear side of the unit.
3.
Plug in power cable to the power port on the unit and one end to the power outlet
(Figure 3.1).
Figure 3.1
‐ 7 ‐
4.
Press Power button to power on the unit.
Enter media type menu to select the correct media for scanning.
(Refer to P.29)
Power button
Media
Type
5.
Press OK/Capture button to capture the image.
OK/Capture button
6.
Press on Playback button to playback the saved images.
Playback button
‐ 8 ‐
7.
After capturing, take out the SD card which stored the saved images.
8.
Alternative to 7, saved picture can be read directly, without taking out the SD card, from PC by entering MSDC mode .
(Refer to P.31)
‐ 9 ‐
Scanning Photo
1.
Remove the film/slide holder as well as the back light holder from the unit if either
one is attached.
Remove film/slide holder by exiting the sliding to the left hand side.
Remove down
backlight the handle
holder and
by pull
it pressing
out.
2.
Open the photo holder frame as illustrated, place the photo on the base of the photo holder and close the photo holder frame.
‐ 10 ‐
3.
Insert the photo holder into the photo slot of the unit.
4.
Enter Media Type Mode to select the correct media for scanning.
(Refer to P.29)
Media
Type
5.
Press OK/Capture button to capture the image.
‐ 11 ‐
OK /Capture button
Scanning Business Card
1.
Follow step 1 from scanning photo to remove the film/slide holder as well as the back light holder in the previous pages.
2.
Open the photo holder frame and place the business card on the base of the photo holder following the engraved guide line.
3.
Put the business card fixture on the top of photo holder.
‐ 12 ‐
4.
Insert the photo holder with business card fixture into the photo slot of the unit.
5.
Enter media type menu to select the correct media for scanning.
(Refer to P.29)
Media
Type
6.
Press OK/Capture button to capture the image.
OK /Capture button
‐ 13 ‐
IV.
Operation Guide
Live View Mode
Playback Mode
‐ 14 ‐
Capture Mode
Setting Mode
1.
Live View Mode
Live View indicator
(flashing at 0.5sec
rate)
After a quick display of welcome page, system will enter the Live View mode.
A flashing red dot appears on the top left hand corner indicating the state in Live View.
(Note:
select correct media type (Refer to P.29) before capturing.
By default the setting is at
Negative Film.
Unit will reset back to the default setting after power off)
1.1
Mirror (Hard Key)
Save & Exit
Up /Mirror
OK /Capture
Up /Mirror button
● Press Up /Mirror button to turn the image left to right, press again vice versa
‐ 15 ‐
1.2
Flip (Hard Key)
Down /Flip
Down /Flip button
Save & Exit
OK /Capture
● Press Down /Flip button to turn the image upside down, press again vice versa
1.3
EV (Hard Key)
Left
Up
/EV
Down
/+
/
‐
Save & Exit
OK /Capture
● Press Left /EV button to enter EV(Brightness) control
‐ 16 ‐
Up /+ button
● Press Up /+ button to increase exposure(brightness) with ranges of ‐ 3 to 3
Down /- button
●
Press Down / ‐ button to decrease exposure(brightness) with ranges of ‐ 3 to 3
1.4
Color (Hard Key)
Up /+
Right /Color
Down / ‐
Save & Exit
OK /Capture
● Press Right /Color button to enter color control
‐ 17 ‐
Up /+ button
● Press Up /+ button to increase Color with ranges of ‐ 3 to 3
Down /- button
● Press Down / ‐ button to decrease Color with ranges of ‐ 3 to 3
Left /Go Previous Right /Go Next
● Press arrow hard key Left and Right to move between R, G, B
‐ 18 ‐
2.
Capture Mode
Right /Go Next
Left /Go Previous
OK /Capture mode
Once user presses the OK/Capture hard key, the live view image is selected and wait for
2 ‐ 3 seconds to enter the Capture mode shown with four icons on the display.
Save to Memory
Rotate +90 Rotate ‐ 90
Selected image
Cancel
●
Save to Memory : save selected image to memory
● Rotate +90 : rotate +90 degrees
●
Rotate ‐ 90 : continue rotate ‐ 90 degrees
(this is for adjusting the user who took the portrait picture)
●
Cancel : cancel all action and return to Live View
‐ 19 ‐
2.1
Save to Memory
Save icon will be highlighted for user to confirm the saving by pressing the OK/Capture button.
After save action the display returns back to Live View.
2.2
Rotate +/ ‐ 90 degrees
OK button
User can manipulate rotate +90 or rotate ‐ 90 with the Left or Right button to highlight
on the rotate +90/ ‐ 90 icon.
Press OK/Capture button to do a clockwise or anti ‐ clockwise rotation and move to Save and Exit screen page.
Press again the OK/Capture button to
save the rotated image or exit without save.
The screen will return back to Live View.
‐ 20 ‐
2.3
Cancel
With Cancel icon highlighted, pressing the OK/Capture button to cancel all action and
return back to the state of Live View.
Nothing will be saved onto the SD card.
2.4
Memory full
OK button
Once the internal memory or SD card is full, user can see a FULL icon showing on the display.
User can either upload the saved images to PC or replace with another SD card for continuing capture.
‐ 21 ‐
2.5
SD card locked
SD card locked icon
If the SD card is locked, press the OK/Capture button will show up a SD Card Locked icon at the center of screen.
Unlock the SD card by switching the bar to unlock position to continue use of the SD card.
2.6
SD card erro r
SD card error indicator
If scanner cannot detect a good working SD card in the SD slot, a warning icon with question mark will appear at the center of screen.
Either format the SD card (Refer to
P.30) or replace with another good SD card for continue operation.
‐ 22 ‐
3.
Playback Mode
Right /Go Next
Left /Go Previous
Press the Playback button to enter the Playback Mode.
3.1
Playback Auto Slide Show
Playback
Mode /Setting
Slide Show Indicator
Once user enters the playback mode, a slide show indicator is showing at the top left hand corner of screen.
The display will start playing all images stored in SD card or internal memory with 2 seconds interval between saved images.
User can pause the slide show by pressing either the Left or Right or Mode hard key.
‐ 23 ‐
3.2
Playback Manual Control
Pausse
Left Left
OR
Right
AND
Right
Auto Slide Show
Press Left OR
Right button to scroll picture
Left
Right
Auto Slide Show
Press Left AND Right button together to resume to Slide Show
3.3
Playback Exit
Playback button
Press the Playback button to exit the Playback Mode to return to Live View Mode.
‐ 24 ‐
3.4
Playback Edit: Rotate+90/Rotate ‐ 90/Mirror/Flip/Delete
Left /Go Previous
Right /Go Next
Mode
OK
/Setting
/Capture
While at the Playback Mode, press the Mode button to enter Playback Manual Control
Mode.
Press the Mode button one more time to enter Playback Edit.
Use Left and Right
button to move to the desired icons and press OK button to confirm the action.
Rotate +90 Delete
Rotate ‐ 90 Mirror Flip
● Rotate +90 : rotate image +90 degrees
●
Rotate ‐ 90 : rotate image ‐ 90 degrees
● Mirror : turn image left to right
● Flip : turn image upside down
● Delete : delete selected image stored in memory
Press the Mode button to resume back to Playback Manual Control Mode.
‐ 25 ‐
3.5
Playback Edit Exit
Mode button
Press the Mode button while at the Playback Edit Mode the display will go back to
Playback Manual Control Mode on current selected picture.
3.6
Playback: Delete
OK button
Delete
With highlight on the Delete icon press OK button will delete the current selected picture and resume back to Playback Manual Control Mode.
If user intends to continue to delete
the images, repeat the process by pressing the Mode button and move to delete icon again and press OK button to confirm.
‐ 26 ‐
3.7
Playback: No Picture
Playback button
If there is no picture inside the internal memory or SD card when pressing the Playback button, a page with Question Mark symbol at the screen center will show up.
The page will remain for 2 seconds and resume back to Live View Mode.
‐ 27 ‐
4.
Setting Mode
Mode (Hard Key)
While in Live View Mode, press the Mode hard key to enter the Setting Mode.
Media Type
Format TV Out
USB Mode
● Media Type : Select the type of media loaded in holder
●
Format : Format Internal memory or SD card
● TV out : select NTSC or PAL according to TV system
●
USB mode : MSDC (Mass Storage Device Class)
‐ 28 ‐
4.1
Setting: Media Type
Color Negative film
Color Negative film
Slide film
B&W Negative film
Slide
B&W Negative
Photo
Photo
Business Card
Plastic Card
Business/Plastic card
‐ 29 ‐
4.2
Setting: Format
OK button
If the internal memory or SD card requires format by scanner, user can enter Format
Mode by pressing the Mode button while under the Live View Mode.
Scroll to the second icon from the left and press OK button to enter format confirmation page.
The highlight is at the Cancel icon by default.
User can press Left or Right button to move to
Confirm or Cancel icon and press the OK button.
Note
If there is no SD card inside the unit, the internal memory will be formatted once processing the Formatting action.
Vice versa, the SD card will be formatted
4.3
Setting: TV out
OK button
‐ 30 ‐
User is able to view the images from a TV display instead of the unit’s own LCD display for bigger viewing pleasure.
By connecting the AV cable to unit’s TV out jet and one end to TV, confirm by pressing OK button to select PAL or NTSC matching to TV system.
The
TV is now working as an alternative display to perform all tasks like scan, capture, edit
and playback.
4.4
Setting: USB Mode
OK button
After capture user can upload the saved images from internal memory or SD card to PC by selecting USB Mode.
Make sure the USB cable is connected between the unit and PC.
Scroll to the USB Mode icon and press the OK button.
The display is showing a USB status icon at the center of screen confirming the unit is now becoming a mass storage device.
User can review or edit images on the external storage device.
Or just take out the SD card from device into PC to read the images directly.
‐ 31 ‐
Good bye page
‐ 32 ‐
V.
Specification
Image Sensor:
Lens:
LCD:
Internal memory:
Focus Range:
Exposure Control:
Color Balance:
Power:
Dimensions:
Weight:
External memory:
5 mega CMOS sensor
F no.=2.0, 4 Glass elements,
3.0’’
24MB
2x
6
6
Color
NAND
Predefined levels levels
of of
TFT
LCD
Flash
Focuses control control
(for
AC adapter power
190x145x205mm
0.90kg
SD/MMC compatible
saving images)
Scan
Data
Scan
Light
Quality:
Method:
Source:
Conversion:
1,800 dpi
10 bits per color channel
Single pass
Film/Slide scanning:
Light bar (3 white LEDs)
Photo/Business Card scanning:
Interface:
Light bar (8 white LEDs)
USB 2.0, TV ‐ out (video 3.5mm
jack)
USB Configuration: Mass Storage Device Class/MSDC
‐ 33 ‐
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: WFZSCND503H1231
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
advertisement
Related manuals
advertisement