QA comments addressed.
NAV E 501 and NAV E 101 • Setup Guide
This guide provides instructions for an experienced installer to install the Extron NAV E 501 and
NAV E 101 streaming encoders and to make all connections. One or more NAV encoders and one or more compatible Extron NAV decoders form an AV distribution and switching matrix on a managed
1G IP network.
IMPO
RTAN
T:
Go to www user guide
.extron.com f
, installation instructions, specifications bef
NOTE: For more information on any subject in this guide, see the NAV E 501 and NAV E 101 User Guide , available at www.extron.com
.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and rack or furniture mount the encoder as required.
Step 2 — Rear Panel Connections
POWER
12V
2.0 A MAX
INPUT
L
AUDIO
R
CONTROL
CONT RS-232 IR
USB 2.0
NAV E 501
RESET
HDMI LOOP THRU C T Tx Rx G S G 5V/200 mA NAV 1G/PoE+ EXT
POWER
12V
1.5 A MAX
INPUT
L
AUDIO
R
CONTROL
CONT RS-232 IR
NAV E 101
RESET
HDMI LOOP THRU C T Tx Rx G S G
NAV 1G/PoE+
Figure 1. NAV E 501 and NAV E 101 Rear Panel Features
A HDMI input port — Connect an HDMI cable between this port and the HDMI output port (or DVI port, with an appropriate adapter) of the digital video source.
B HDMI Loop Thru port — Connect a display to this female HDMI connector for local loop-through monitoring of the source signal.
NOTE:
See ® Lacing Brackets
on page 6 to securely fasten the HDMI connectors to the encoder for A and B .
C AUDIO input port
— Connect balanced or unbalanced stereo audio input to this 5-pole, 3.5 mm captive screw connector (see Analog audio input on page 6 to wire the connector).
D Control Contact Closure port — Connect an Extron Show Me ® cable to the port to allow the encoder to select itself as the input to the decoder, using the control system.
E Control RS-232/IR port — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 and IR communication with connected remote controlled devices. Control is accomplished using
an Extron control system (see Control connector
on page 6 to wire the connector).
F USB 2.0 port (NAV E 501 only) — Connect a USB Type-C cable from a USB host or a USB device. See
LockIt ®
securely fasten the USB connector to the encoder.
Lacing Brackets
to
NOTE: This connector is limited to supplying 200 mA in USB device mode.
G NAV 1G/PoE+ port — Connect to an Ethernet LAN on which one or more decoders also reside for streaming and control. This port
can also receive Power over Ethernet (PoE+) to power the encoder (see Power on page 3 for power options).
H Extension port (NAV E 501 only) — If desired, connect another networked device to this port. The port acts as a networked switch to the NAV 1G/PoE+ port.
NOTE: The Extension port cannot provide PoE.
I Reset button and LED — This button initiates three modes of reset (see the NAV E 501 and NAV E 101 User Guide , available at www.extron.com
, for details).
J Power connector (optional) — Plug the included external 12 VDC power supply into this 2-pole connector for local power (see
Power connector
on page 6 to wire the connector and Power
for power options).
1
2
NAV E 501 / NAV E 101 • Setup Guide (Continued)
Step 3 — Front Panel Configuration Port Connection
CONFIG
HDMI
HDCP
INPUTS
HDMI AUDIO
ANALOG
AUDIO
NAV
STREAM
USB
USB
HOST
ACTIVE
LAN
NAV
-LNK-
EXT
-ACT-
ID
NAV E 501
F G
LAN ID
HDMI
HDCP
INPUTS
HDMI AUDIO
ANALOG
AUDIO
NAV
STREAM
CONFIG
LNK
ACT
NAV E 101
Figure 2. NAV E 501 and NAV E 101 Front Panel Features
A Configuration (CONFIG) port — Connect a PC to the encoder via this front panel USB Mini-B connector for configuration of the unit.
The port uses IP over USB technology. The IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also discoverable via Extron Toolbelt (see the NAV E 501 and NAV E 101 User Guide . The guide and Toolbelt are available for download at www.extron.com
).
Indicators
B Power LED — Indicates power and startup status, as follows:
• Blinking — The unit is receiving power, either locally or remotely (via PoE) and is booting up.
• Lit steadily — The unit is receiving power, either locally or remotely (via PoE) and is operational.
C INPUTS — Indicate status of the signal inputs, as follows:
• HDMI LED — The encoder is detecting an HDMI input.
• HDCP LED — The HDMI signal is HDCP encrypted.
• HDMI Audio LED — The embedded HDMI audio input is selected.
• Analog Audio LED — The analog audio input is selected.
D NAV LEDs — Indicate the output status of the AV and USB streams, as follows:
• Stream
• Lit steadily – The encoder is actively streaming a NAV output consisting of video, audio, or both.
• Blinking – The encoder is actively streaming a NAV output, but network errors are present.
• Unlit - The encoder is not actively streaming a NAV output.
• USB (NAV E 501 only)
• Lit steadily – The encoder is actively sending and receiving a NAV USB stream.
• Blinking – The encoder is unable to establish a NAV USB stream.
• Unlit — The encoder is not actively sending and receiving a NAV USB Stream.
E USB LEDS (NAV E 501 only)— Indicates the status of the USB stream, as follows:
• Host
• Lit steadily – The encoder is in USB host mode, the default condition.
• Unlit – The encoder is in USB device mode.
• Active
• Lit steadily – A host or USB device is connected to the rear panel USB port.
• Unlit – No host or USB device is connected to the rear panel USB port.
• Blinking – A USB device or hub is connected to the encoder and is drawing more power than the USB port can supply.
F LAN LEDs (see figure 2 on page 2) —
Indicate the status of the network connections, as follows:
• NAV LED (NAV E 501) or LAN LED (NAV E 101) —
• Link LED — Lit steadily indicates that a network link is established.
• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.
• EXT LED (NAV E 501 only) —
• Link LED — Lit steadily indicates that a network link is established. Blinking indicates a link speed less than 100 Mbps.
• Act LED — Blinking indicates network traffic. The blink rate corresponds to activity.
G ID button and LED
— The recessed ID button identifies the encoder when pressed. The LED blinks when the encoder is in pairing mode (see
Pairing devices on front panel
on page 5 for details).
Operation
Power
The encoder can be powered in one of three ways:
•
Locally, from the included external power supply and via the power connector (see J on page 1).
• Remotely, receiving PoE via the NAV 1G/PoE+ port (see
G ), either from the network switch or from an optional PI 140 Power Injector.
• Locally (
J ) and remotely ( G
), with priority on the NAV 1G/PoE+ port. If PoE voltage drops below a threshold, the encoder immediately transitions to the external power connector with no effect on system operation.
When power is applied, the encoder runs a series of self-tests that blink the front panel Power LED and all other indicators. The encoder then boots the NAV operating system. It can take approximately 45 seconds for self-test and system startup to complete. When the process is complete, the Power LED lights steadily.
NOTE: The encoder is NOT operational until the boot process is complete (the Power LED is lit steadily).
System Operation
The encoder can be configured and controlled using embedded web pages or Toolbelt software (see the NAV E 501 and NAV E 101 User
Guide available at www.extron.com
).
NOTE:
The “Connection via web pages,” Connection settings , and
Pairing devices via front panel
procedures (see page 5) may
NOT be necessary if your system includes a NAVigator System Manager.
Connection via web pages
Connection to the encoder and its embedded web pages can be made via either the front panel Configuration (USB) port (using IP over
USB technology) (see figure 2 ,
A
) or the rear panel NAV 1G/PoE+ port (see figure 1
, G
on page 1).
Access the encoder using HTML pages as follows:
1. Start a web browser.
NOTES:
• Suggested browsers to fully support the NAV system are: Google Chrome™, Mozilla™, Firefox™, and Microsoft ® Edge™.
• The network must be properly configured for multicasting (IGMP). Failure to do so may result in degraded performance.
2. Enter the IP address of the encoder in the browser Address field.
NOTE :
• Default settings:
Port
Config (USB) *
NAV/PoE + (RJ-45)
DHCP IP address
203.0.113.22
Subnet mask
On
* For the Config port , the address for IP over USB CANNOT be changed.
• If you use IP over USB, Extron recommends waiting a minute after plugging in the cable for your PC to identify the USB connection as a valid Ethernet port.
3
4
NAV E 501 / NAV E 101 • Setup Guide (Continued)
3. Press the keyboard < Enter > key. The browser displays
a privacy error message (see figure 3 at right for an
example in the Chrome browser).
4. Click Advanced (see figure 3, appear below the button.
1 ). The button changes to Hide Advanced and explanatory text and a link
5. Click Proceed to < IP address > (unsafe) ( 2 ). The browser opens to the Login dialog box (see figure 4).
Figure 3. Privacy Error Message (in Chrome Browser)
Figure 4. Login Dialog Box
6. Complete the Username (see figure 4, 1 ) and Password the embedded web pages (see figure 5 on page 5).
( 2 ) fields and click Sign In ( 3 ). The browser opens to the home page of
NOTES:
• The default username is admin .
• The factory configured passwords for all accounts on this device have been set to the device serial number. If the password is reset, the encoder defaults to the default password, which is extron .
• Usernames and passwords are case sensitive.
2
1
*
* NAV E 501 only
Figure 5. Home Page
NOTE: Detailed descriptions of communication, configuration, and monitoring are provided in the NAV E 501 and NAV E 101 User
Guide , available at www.extron.com
.
Connection settings
View and change connection settings as follows:
1. On the home page, click Settings (see figure 5, 1 ) > Network
Connection ( 2 ). The Network Connection pane opens (see figure 6 at right), showing protected views of the network connection settings.
NOTE: Editing of connection settings is disabled when the device is assigned to an Extron NAVigator System Manager.
2. To change the settings , click Edit (see figure 6, changes to Save .
1 ). The Edit button
3. Click in the desired field ( 2 ) and edit it as desired.
4. Repeat step 3 as necessary for other values.
5. Click Save .
Pairing devices via front panel
Pair devices from the front panel as follows:
ID
1. Use an Extron Tweeker or other small screwdriver to press and hold the encoder front panel ID button for approximately 3 seconds, until the ID LED blinks. The encoder enters pairing mode, which allows decoders to receive the AV stream (NAV E 101) or AV and USB streams (NAV E 501 only) from encoders.
2. One at a time, use a Tweeker or other small screwdriver to press and hold the decoder front panel ID button for approximately 3 seconds, until the
ID LED blinks. The decoder is now paired to the encoder.
3. Repeat step 2 for each decoder.
*
* NAV E 501 only
Figure 6. Network Connection Pane
5
6
NAV E 501 / NAV E 101 • Setup Guide (Continued)
4. Use a Tweeker or other small screwdriver to press and release the encoder front panel ID button. The encoder exits pairing mode.
5. Repeat steps 1 through 4 to pair decoders to other encoders.
After all devices are connected, powered on, and paired, the system is fully operational.
Operation in a System with a NAVigator
The Extron NAVigator is a system manager that easily configures and controls the NAV System. The NAVigator can support a 16 endpoint system by default, but if a LinkLicense is installed, it can support up to 240 endpoints.
See the NAVigator User Guide , available at www.extron.com
for details.
Connection Details
LockIt
®
Lacing Brackets
1. Plug the HDMI cable or USB (NAV E 501 only) into the panel connection (see 1 , at right).
2. Loosen the connection mounting screw from the panel enough to allow the LockIt lacing bracket to be placed over it ( 2 ). The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the connector ( 3 ).
4. Tighten the screw to secure the bracket.
ATTENTION
:
• Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel elle est attachée est très fin et peut facilement être dénudé.
3
5. Loosely place the included tie wrap around the connector and the LockIt lacing bracket as shown ( 4 ).
6. While holding the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any excess length ( 5 ).
Analog audio input Control connector
Do not tin the wires!
Tip
Sleeve
Tip
Sleeve
Unbalanced Stereo Input
Tip
Ring
Sleeves
Tip
Ring
Balanced Stereo Input
IR Device
Rx Tx
NAV and EXT connectors
Pins:
12345678
4
5
6
7
Pin
1
2
3
TIA/EIA T568B
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
8
White-brown
Brown
TP Wires
Tx Rx Gnd
RS-232 Device
Power connector
Smooth
Ridges
SECTION A–A
Power Supply
Output Cord
A
Captive
Screw
Connector
3"
16 (5 mm) MAX
A
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance
Guide on the Extron website.
© 2020 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
68-2751-50 Rev. B
09 20
