advertisement
BrightLink
®
Pro 1410Wi User's Guide
Contents
3
4
5
6
7
8
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears................ 229
Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear ......... 234
9
10
BrightLink Pro 1410Wi User's Guide
Welcome to the BrightLink Pro 1410Wi
User's Guide
.
11
Introduction to Your Projector
Refer to these sections to learn more about your projector and this manual.
Notations Used in the Documentation
Where to Go for Additional Information
Projector Features
The BrightLink Pro 1410Wi projector includes these special features:
Unique interactive functions
• Whiteboard annotation without a computer, including saving, printing, and emailing content
• Annotation with two pens at the same time
• Split screen annotation on two sources at the same time
• Computer interaction over a network
• Control pad included for easy connections and operation
• Video conferencing without a flat panel display
Ultra short throw projection system
• Project an 87-inch (221-cm) image (WXGA) from just 9.1 inches (231 mm) away
• Easily mounted on a wall or table for fast, low-cost installations
• Can be mounted vertically to create an interactive workspace directly on a table surface
• Can be placed on a table or desk for portability
• Reduced shadow interference and glare
Bright, high-resolution images
• Up to 3100 lumens of brightness (white light output and color light output)
• Native resolution of 1280 × 800 pixels (WXGA)
Flexible connectivity
• HDMI port for computer or video device connection
• DisplayPort for high-performance computer connection
12
• Plug-and-play 3-in-1 USB projection, audio, and mouse control for instant setup
• Wired and wireless network support for projection and interaction
• Projector monitoring and control via remote network computer
• PC Free presentations via connected USB memory devices
• Port for connecting an external monitor
Innovative display and operation features
• Low total cost of ownership with long-life projector lamp and high-efficiency air filter
• High digital zoom ratio for larger images in shorter projection distances
• 3000:1 contrast ratio and Auto Iris control for sharp, detailed images
• Built-in closed captioning decoder
• 10 W speaker system with audio out port for connecting external speakers
• Epson's Instant Off and Direct Power On features for quick setup and shut down
• Support for Crestron RoomView network monitoring systems
• Network message broadcast system to project timely messages to all networked projectors
Optional Equipment and Replacement Parts
Warranty and Registration Information
Parent topic:
Introduction to Your Projector
Related concepts
Product Box Contents
Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
Make sure your projector box included all of these parts:
13
1 Projector
2 Remote control
3 Remote control batteries (two AA alkaline)
4 2 Pens and batteries (one AA alkaline battery for each pen)
5 USB cables
6 Power cord
7 Battery charger with 2 AA rechargeable pen batteries (included in the US and Canada only)
8 Pen tray
9 Password Protected sticker
10 Projector feet
14
11 Projector software CD-ROM (for network usage)
12 Projector software for Easy Interactive Function CD-ROM
13 Projector documentation CD-ROM
14 Wireless LAN module
15 Control pad and batteries (two AA alkaline)
Parent topic:
Related concepts
Related tasks
Additional Components
Depending on how you plan to use the projector, you may need to obtain the following additional components:
• To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You can purchase one from Epson or an authorized Epson reseller.
• To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller.
• To receive a DisplayPort signal, you need a compatible DisplayPort cable. See your local computer or electronics dealer for purchase information.
• To project with audio from certain ports, you may need a commercially available audio cable compatible with your device. See your local computer or electronics dealer for purchase information.
• If you did not purchase a mount that included a VGA cable, you may need a VGA computer cable. You can purchase one from Epson or an authorized Epson reseller.
Parent topic:
Related references
Optional Equipment and Replacement Parts
15
Optional Equipment and Replacement Parts
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com
(U.S. sales) or www.epson.ca
(Canadian sales).
Epson offers the following optional accessories and replacement parts for your projector:
Option or part
Genuine Epson replacement lamp (ELPLP71)
Air filter replacement (ELPAF40)
Ultra short throw wall mount
Ultra short throw table mount
Replacement wireless LAN module (ELPAP07)
Quick Wireless Connection USB key (ELPAP09)
Additional interactive pen (ELPPN03A/ELPPN03B)
Replacement set of 6 pen tips (ELPPS01)
Active speakers (ELPSP02)
On Wall Cable Management Kit
Kensington security lock
6 ft (1.8 m) VGA computer cable (ELPKC02)
10 ft (3.0 m) VGA computer cable (ELPKC09)
25 ft (20 m) VGA computer cable (ELPKC10)
HD-TV cable
Remote control cable set for control pad
Component-to-VGA video cable (ELPKC19)
1-Year Extended Depot Repair Service Plan
1-Year Extended Exchange Warranty
2-Year Extended Depot Repair Service Plan
Part number
V13H010L71
V13H134A40
V12H517020
V12H516020
V12H418P12
V12H005M09
V12H522001/V12H523001
V12H524001
V12H467020
ELPCK01
ELPSL01
F3H982-06
F3H982-10
F3H982-25
ELPKC22
ELPKC28
V12H005C19
EPPFTPA1
EPPEXPA1
EPPFTPA2
Parent topic:
16
Warranty and Registration Information
Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty that came with your projector.
In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.
Register your product online using the projector CD or at this site: www.epson.com/webreg .
Registering also lets you receive special updates on new accessories, products, and services.
Parent topic:
Notations Used in the Documentation
Follow the guidelines in these notations as you read your documentation:
•
Warnings
must be followed carefully to avoid bodily injury.
•
Cautions
must be observed to avoid damage to your equipment.
•
Notes
contain important information about your projector.
•
Tips
contain additional projection information.
Parent topic:
Introduction to Your Projector
Where to Go for Additional Information
Need quick help on using your projector? Here's where to look for help:
• Built-in help system
Press the
Help
button on the remote control or projector to get quick solutions to common problems.
• Help icon on the bottom whiteboard toolbar
Select the help icon to get a quick summary of the tools and features available.
• www.epson.com/support (U.S) or www.epson.ca/support (Canada)
View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24 hours a day.
• For detailed instructions on using your projector in a network environment, see the
EasyMP Network
Projection Operation Guide
.
17
• For detailed instructions on converting PowerPoint files into a slide show file format that you can display from a USB device connected to your projector (Windows only), see the
EasyMP Slide
Converter Operation Guide
.
• If you still need help after checking this manual and the sources listed above, you can use the Epson
PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Parent topic:
Introduction to Your Projector
Related references
Related tasks
Using the Projector Help Displays
Projector Part Locations
Check the projector part illustrations to learn about the parts on your projector.
Projector Parts - Interface Panel
Projector Parts - Control Panel
Projector Parts - Interactive Pens
Projector Parts - Remote Control
Parent topic:
Introduction to Your Projector
18
Projector Parts - Front/Top
1 Remote control receiver
2 Speaker
3 Control panel
4 Cable cover screw
5 Cable cover
6 Exhaust vent
7 Lamp cover screw
8 Lamp cover
Parent topic:
19
Projector Parts - Side
1 Filter cover switch
2 Security cable installation slot
3 Wireless LAN light
4 Interactive pen receiver
5 Obstacle sensor
6 Remote receiver
7 Projection window
8 Security lock port
9 Air filter cover
20
10 Air intake vent (air filter)
11 Focus lever
Parent topic:
Projector Parts - Interface Panel
1 Wireless LAN unit slot
2
Audio
port for computer audio
3
Computer
port
4
Audio Out
port
5
USB-B
port for control pad or computer
6
Monitor Out
port
7 Network (
LAN
) port
8
HDMI
port
9
DisplayPort
port
10
Audio
port for specific source set in the Extended menu (
Audio Input Setup
)
11
RS-232C
port
21
12 Power inlet
13
USB-A
port for control pad
14
USB-A
port for document camera
15
Video
port
16
Audio
port (for sound from equipment connected to the
Video
port)
17
Remote
port for connecting to the control pad with an optional cable
Parent topic:
Projector Parts - Base
1 Ceiling mount holes (5)
2 Security cable attachment point
3 Rear foot attachment holes (2)
22
4 Wall mount plate holes (4)
5 Front foot attachment hole
Parent topic:
Projector Parts - Control Panel
1 Projector status lights
2
Source Search
button (searches for connected video sources)
3
Enter
button (selects options)
4 Horizontal/Vertical keystone adjustment buttons (display the adjustment screen) and arrow buttons
5 Help button (accesses projector help information)
6
Esc
button (cancels/exits functions)
7
Wide
/
Tele
buttons (adjust projected image size), horizontal keystone adjustment buttons (adjust screen shape), and arrow buttons
8
Menu
button (accesses projector menu system)
9 Power button
23
Parent topic:
Related references
Projector Parts - Interactive Pens
1 Pen tip
2 Attachment for optional strap or cord
3 Battery light
4 Power switch
5 Battery cover
Parent topic:
24
Projector Parts - Remote Control
1 Power button
2
Capture
button (captures projected image in annotation mode)
3
button (prints the projected image)
4 Numeric buttons (enter numbers)
5
Auto
button (automatically adjusts position, tracking, and sync settings)
6
Aspect
button (selects the image aspect ratio)
25
7
Num
button (when held down, switches numeric buttons to number function)
8
Menu
button (accesses projector menu system)
9 Arrow buttons (move through on-screen options and control wireless mouse functions)
10 Enter button (selects options and controls wireless mouse functions)
11
User
button (customizable for different functions; starts auto calibration by default)
12
Page
up/down buttons (control presentation slides)
13
E-Zoom +
/
–
buttons (zoom into and out of the image)
14
A/V Mute
button (turns off picture and sound)
15
Split
button (splits the screen so you can project two images)
16 Strap attachment hole (strap not included)
17
Help
button (accesses projector help information)
18
Freeze
button (stops video action)
19
Volume
up/down buttons (adjust speaker volume)
20
Pointer
button (activates on-screen pointer)
21
Esc
button (cancels/exits functions and controls wireless mouse functions)
22
Pen Mode
button (switches between annotation and computer interactive modes)
23
Color Mode
button (selects display modes)
24
Whiteboard
button (switches to whiteboard mode)
25
Save
button (saves the projected image)
26
Source Search
button (searches for connected sources)
27 Light emitting area (outputs remote control signals)
Parent topic:
26
Projector Parts - Pen Tray
1 Wall attachment holes
2 Optional security lock attachment hole
Parent topic:
27
Projector Parts - Control Pad
1 Power button
2
Whiteboard
button (switches to whiteboard mode)
3
Source Search
button (searches for connected sources)
4
Capture
button (captures projected image in annotation mode)
5
button (prints the projected image)
6
Save
button (saves the projected image)
7 USB-B port for connecting a computer (on bottom of control pad)
8
USB-A
port for connecting a USB thumbdrive or other storage device (under bottom cover)
9
Printer
USB-A port for connecting a printer (under top cover)
10
USB-B
port for connecting to the projector for printing or thumbdrive access (under top cover)
11
USB-A
port for connecting to the projector for interactive functions (under top cover)
12
Remote
port for connecting the optional remote control cable (under top cover)
28
13 Light emitting areas (output remote control signals)
14 Bottom cover (open to connect a USB thumbdrive or other storage device)
15 Top cover (open to connect cables or replace batteries)
16 Cable cover (open when cables are wired along a wall)
Parent topic:
29
Setting Up the Projector
Follow the instructions in these sections to set up your projector for use.
Removing and Attaching the Cable Cover
Connecting a Printer to the Control Pad
Installing Batteries in the Remote Control
Installing Batteries in the Pens
Installing Batteries in the Control Pad
Projector Placement
Your ultra-short throw projector is designed to be installed on a wall or vertically on a table to create an interactive tabletop workspace.
You can also place the projector on a flat surface such as a desk or table to project in a portable setup.
Keep these considerations in mind as you select a projector location:
• Follow the instructions in the
Installation Guide
to install the projector using the included mounting equipment.
• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents.
• Position the projector within reach of a grounded electrical outlet or extension cord.
• If the projector is not mounted, place it on a sturdy, level surface.
Projector Setup and Installation Options
Parent topic:
Projector Setup and Installation Options
You can set up or install your projector in the following ways:
Mounted on the wall or ceiling
30
Mounted vertically on a table to create an interactive workspace.
Front projection from a table or portable cart
Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an angle.
If you project from a table or portable cart, be sure to select the correct
Projection
option in the projector's menu system.
31
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Projection Distance
The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.
Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image. (Conversion figures may have been rounded up or down.) For more detailed information and installation instructions for the wall mount, see the
Installation Guide
. You can also use the projector Throw Distance Calculator at www.epson.com/support (U.S.) or www.epson.ca/support (Canada).
16:10 Aspect Ratio
Diagonal Min. ceiling Image width Image height Min. projection Distance from top image height distance from of image to wall size front of projector plate
6.9 inches (17.4 cm) 60 inches 78.7 inches 50.9 inches
(199.8 cm) (129.2 cm)
70 inches 85.0 inches 59.4 inches
(215.9 cm) (150.8 cm)
31.8 inches
(80.8 cm)
37.1 inches
(94.2 cm)
2.5 inches
(6.2 cm)
4.9 inches
(12.4 cm)
7.9 inches (20.1 cm)
9.0 inches (22.7 cm) 80 inches 91.4 inches 67.8 inches
(232.0 cm) (172.3 cm)
88 inches 96.4 inches 74.6 inches
(245.0 cm) (189.5 cm)
90 inches 97.7 inches 76.3 inches
(248.2 cm) (193.9 cm)
100 inches 104.1 inches 84.8 inches
(264.3 cm) (215.4 cm)
42.4 inches
(107.7 cm)
46.6 inches
(118.5 cm)
47.7 inches
(121.2 cm)
53.0 inches
(134.6 cm)
7.3 inches
(18.7 cm)
9.3 inches
(23.6 cm)
9.8 inches
(24.9 cm)
12.2 inches
(31.1 cm)
9.8 inches (24.9 cm)
10.0 inches
(25.4 cm)
11.1 inches
(28.1 cm)
16:9 Aspect Ratio
32
Diagonal Min. ceiling Image width Image height Min. projection Distance from top image height distance from of image to wall size front of projector plate
8.5 inches (21.7 cm) 59 inches 77.5 inches 51.5 inches
(196.8 cm) (130.6 cm)
60 inches 78.1 inches 52.3 inches
(198.3 cm) (132.8 cm)
28.9 inches
(73.5 cm)
29.4 inches
(74.7 cm)
2.6 inches
(6.6 cm)
2.9 inches
(7.3 cm)
8.7 inches (22.0 cm)
70 inches 84.3 inches 61.0 inches
(214.2 cm) (155.0 cm)
77 inches 88.7 inches 67.1 inches
(225.3 cm) (170.5 cm)
80 inches 90.6 inches 69.7 inches
(230.1 cm) (177.1 cm)
90 inches 96.8 inches 78.4 inches
(246.0 cm) (199.2 cm)
97 inches 101.2 inches 84.5 inches
(257.1 cm) (214.7 cm)
34.3 inches
(87.2 cm)
37.8 inches
(95.9 cm)
39.2 inches
(99.6 cm)
44.1 inches
(112.1 cm)
47.6 inches
(120.8 cm)
5.4 inches
(13.7 cm)
7.1 inches
(18.1 cm)
7.9 inches
(20.0 cm)
10.4 inches
(26.4 cm)
12.2 inches
(30.9 cm)
10.0 inches
(25.4 cm)
11.0 inches
(27.8 cm)
11.4 inches
(28.9 cm)
12.7 inches
(32.3 cm)
13.7 inches
(34.7 cm)
4:3 Aspect Ratio
Diagonal Min. ceiling Image width Image height Min. projection Distance from top image height distance from of image to wall size front of projector plate
6.9 inches (17.4 cm) 53 inches 78.7 inches 42.4 inches
(199.8 cm) (107.7 cm)
60 inches 83.7 inches 48 inches
(212.5 cm) (121.9 cm)
31.8 inches
(80.8 cm)
36 inches
(91.4 cm)
2.5 inches
(6.2 cm)
4.4 inches
(11.2 cm)
7.7 inches (19.5 cm)
8.9 inches (22.5 cm) 70 inches 90.9 inches 56.0 inches
(230.8 cm) (142.2 cm)
77 inches 95.9 inches 61.6 inches
(243.6 cm) (156.5 cm)
80 inches 98.1 inches 64 inches
(249.1 cm) (162.6 cm)
42 inches
(106.7 cm)
46.2 inches
(117.3 cm)
48 inches
(121.9 cm)
7.2 inches
(18.2 cm)
9.1 inches
(23.1 cm)
9.9 inches
(25.2 cm)
9.7 inches (24.7 cm)
10.1 inches
(25.6 cm)
33
Diagonal Min. ceiling Image width Image height Min. projection Distance from top image height distance from of image to wall size front of projector plate
88 inches 103.8 inches 70.4 inches
(263.7 cm) (182.9 cm)
52.8 inches
(134.1 cm)
12.1 inches
(30.8 cm)
11.0 inches
(28.0 cm)
Parent topic:
Installing the Projector Feet
To use the projector on a table or cart, you first need to install the feet. You can then use the feet to adjust the image position.
1.
Turn the projector upside down.
2.
Insert the larger front foot into the hole at the front of the projector.
1 Front foot (larger)
2 Rear feet
3.
Insert the two smaller rear feet into the holes at the back of the projector.
Parent topic:
34
Removing and Attaching the Cable Cover
Before you can connect equipment to your projector, you need to remove the cable cover.
1.
Remove both of the cable cover screws (screwdriver not included).
2.
Slide off the cable cover.
To attach the cable cover, slide it into position, then tighten the screws.
Parent topic:
Projector Connections
You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound.
• Connect any type of computer that has a USB port, standard video output (monitor) port, DisplayPort, or HDMI port.
• For video projection, connect devices such as DVD players, gaming consoles, digital cameras, and smartphones with compatible video output ports.
• If your presentation or video includes sound, you can connect audio input cables, if necessary.
35
• For slide shows or presentations without a computer, you can connect USB devices (such as a flash drive or camera) or an optional Epson document camera.
Caution:
If you will use the projector at altitudes above 4921 feet (1500 m), turn on
High Altitude Mode
to ensure the projector's internal temperature is regulated properly.
Connecting to Computer Sources
Connecting to an External Computer Monitor
Connecting to External Speakers
Connecting to External USB Devices
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Connecting to Computer Sources
Follow the instructions in these sections to connect a computer to the projector.
Connecting to a Computer for USB Video and Audio
Connecting to a Computer for VGA Video
Connecting to a Computer for HDMI Video and Audio
Connecting to a Computer for DisplayPort Video and Audio
Connecting to a Computer for Pen Use or USB Mouse Control
Connecting to a Computer for Sound
Connecting a Computer to the Control Pad
Parent topic:
Connecting to a Computer for USB Video and Audio
If your computer meets the system requirements, you can send video and audio output to the projector through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a
USB cable.
You can also connect your computer to the control pad.
Note:
This also lets you use the interactive pens with your computer. You need to adjust the
USB Type
B
setting in the projector's Extended menu before you can project through the USB port. Note that using
36
USB Display will slow interactive pen function. For the best performance, VGA, HDMI, or DisplayPort connections are recommended.
1.
Turn on your computer.
2.
Connect the cable to your projector's
USB-B
port.
3.
Connect the other end to any available USB port on your computer.
4.
To use USB Display, do one of the following:
•
Windows 8
: Click
EPSON_PJ_UD
in the upper right-corner, then select
Run EMP_UDSE.exe
in the dialog box that appears to install the Epson USB Display software.
•
Windows 7/Windows Vista
: Select
Run EMP_UDSE.exe
in the dialog box that appears to install the Epson USB Display software.
•
Windows XP
: Wait as messages appear on your computer screen and the projector installs the
Epson USB Display software on your computer.
•
Windows 2000
: Select
Computer
,
EPSON_PJ_UD
, and
EMP_UDSE.EXE
to install the Eposn
USB Display software.
•
Mac OS X
: The USB Display setup folder appears on your screen. Select
USB Display Installer
and follow the on-screen instructions to install the Epson USB Display software.
Follow any on-screen instructions. You need to install this software only the first time you connect the projector to the computer.
The projector displays the image from your computer's desktop and outputs sound, if your presentation contains audio.
Parent topic:
Connecting to Computer Sources
37
Related references
Projector Setup Settings - Extended Menu
Related tasks
Connecting a Computer to the Control Pad
Connecting to a Computer for VGA Video
You can connect the projector to your computer using a VGA computer cable.
Note:
To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.
Contact Apple for compatible adapter options.
1.
If necessary, disconnect your computer's monitor cable.
2.
Connect the VGA computer cable to your computer's monitor port.
3.
Connect the other end to a
Computer
port on the projector.
4.
Tighten the screws on the VGA connectors.
Parent topic:
Connecting to Computer Sources
Connecting to a Computer for HDMI Video and Audio
If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Note:
To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's
HDMI
port.
Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the
HDMI
port.
38
1.
Connect the HDMI cable to your computer's HDMI output port.
2.
Connect the other end to the projector's
HDMI
port.
Parent topic:
Connecting to Computer Sources
Connecting to a Computer for DisplayPort Video and Audio
If your computer has a DisplayPort or Mini DisplayPort connector, you can connect it to the projector using an optional DisplayPort cable.
1.
Connect the DisplayPort cable to your computer's DisplayPort or Mini DisplayPort connector.
2.
Connect the other end to the projector's
DisplayPort
connector.
Parent topic:
Connecting to Computer Sources
Connecting to a Computer for Pen Use or USB Mouse Control
If you connected your computer to a
Computer
,
HDMI
, or
DisplayPort
port on the projector, you also need to connect the USB cable so you can use the pens with your computer.
Note:
You can connect you computer to the control pad instead of directly to the projector.
39
Connecting the USB cable also lets you set up the remote control to act as a wireless mouse, but you cannot use this feature at the same time you are using the pens with your computer.
1.
Connect the USB cable to your projector's
USB-B
port.
2.
Connect the other end to any available USB port on your computer.
If you want to use the remote control as a wireless mouse, you need to change the
USB Type B
setting in the projector's Extended menu. You may also need to configure your computer to work with an external USB mouse. See your computer documentation for details.
Parent topic:
Connecting to Computer Sources
Related references
Projector Setup Settings - Extended Menu
Related tasks
Connecting a Computer to the Control Pad
Using the Remote Control as a Wireless Mouse
Connecting to a Computer for Sound
If your computer presentation includes sound and you did not connect it to the projector's
USB-B
,
DisplayPort
, or
HDMI
port, you can still play sound through the projector's speaker system. Just connect an optional 3.5 mm stereo mini-jack audio cable as described here.
1.
Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port.
40
2.
Connect the other end to the
Audio
port that corresponds to the
Computer
port you are using.
Parent topic:
Connecting to Computer Sources
Connecting a Computer to the Control Pad
If your computer meets the system requirements, you can send video and audio output to the projector through the control pad's
USB-B
port (preferably USB 2.0). Connect the projector and your computer to the control pad using USB cables.
Caution:
Make sure the control pad is positioned no more than 6.5 ft (2 m) away from the projector, and no obstacles are blocking the signal from the projector. Do not place the control pad behind the projection surface.
Note:
This also lets you use the interactive pens with your computer. You need to adjust the
USB Type
B
setting in the projector's Extended menu before you can project through the USB port. Note that using
USB Display will slow interactive pen function. For the best performance, VGA, HDMI, or DisplayPort connections are recommended, in addition to the USB connection for interactive pen usage.
1.
Turn on your computer.
2.
Make sure a USB cable is connected between the
USB-B
port on the projector and the
USB-A
port on the control pad.
41
3.
Connect another USB cable to the USB port on the bottom of the control pad and any available USB port on your computer.
4.
To use USB Display, do one of the following:
•
Windows 8
: Click
EPSON_PJ_UD
in the upper right-corner, then select
Run EMP_UDSe.exe
in the dialog box that appears to install the Epson USB Display software.
•
Windows 7/Windows Vista
: Select
Run EMP_UDSE.exe
in the dialog box that appears to install the Epson USB Display software.
•
Windows XP
: Wait as messages appear on your computer screen and the projector installs the
Epson USB Display software on your computer.
•
Windows 2000
: Select
Computer
,
EPSON_PJ_UD
, and
EMP_UDSE.EXE
to install the Epson
USB Display software.
•
Mac OS X
: The USB Display setup folder appears on your screen. Select
USB Display Installer
and follow the on-screen instructions to install the Epson USB Display software.
Follow any on-screen instructions. You need to install this software only the first time you connect the projector to the computer.
The projector displays the image from your computer's desktop and outputs sound, if your presentation contains audio.
Parent topic:
Connecting to Computer Sources
Related references
Projector Setup Settings - Extended Menu
42
Connecting to Video Sources
Follow the instructions in these sections to connect video devices to the projector.
Connecting to an HDMI Video Source
Connecting to a Component-to-VGA Video Source
Connecting to a Composite Video Source
Connecting to a Video Source for Sound
Parent topic:
Connecting to an HDMI Video Source
If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.
The HDMI connection provides the best image quality.
1.
Connect the HDMI cable to your video source's HDMI output port.
2.
Connect the other end to the projector's
HDMI
port.
Parent topic:
Connecting to a Component-to-VGA Video Source
If your video source has component video ports, you can connect it to the projector using a componentto-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable.
1.
Connect the component connectors to your video source's color-coded component video output ports, usually labeled
Y
,
Pb
,
Pr
or
Y
,
Cb
,
Cr
. If you are using an adapter, connect these connectors to your component video cable.
43
2.
Connect the VGA connector to the projector's
Computer
port.
If your image colors appear incorrect, you may need to change the
Input Signal
setting in the projector's
Signal menu.
Parent topic:
Related references
Input Signal Settings - Signal Menu
Optional Equipment and Replacement Parts
Connecting to a Composite Video Source
If your video source has a composite video port, you can connect it to the projector using an optional
RCA-style video or A/V cable.
1.
Connect the cable with the yellow connector to your video source's yellow video output port.
2.
Connect the other end to the projector's
Video
port.
Parent topic:
44
Connecting to a Video Source for Sound
You can play sound through the projector's speaker system if your video source has audio output ports.
Connect the projector to the video source using a stereo mini-jack adapter cable (with one 3.5 mm miniplug and two RCA plugs).
1.
Connect the audio cable to your video source's audio-out ports.
2.
Connect the other end of the cable to the projector's
Audio
port or ports.
Parent topic:
Connecting to an External Computer Monitor
If you connected the projector to a computer using a
Computer
port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible.
Note:
Monitors that use a refresh rate less than 60 Hz may not be able to display images correctly.
1.
Make sure your computer is connected to the projector's
Computer
port. If there are two computer ports, make sure you use the
Computer1
port.
45
2.
Connect the external monitor's cable to your projector's
Monitor Out
port.
Parent topic:
Connecting to External Speakers
To enhance the sound from your presentation, you can connect the projector to external self-powered speakers. You can control the volume using the projector's remote control.
If you want to output audio from the external speakers when the projector is turned off, you need to adjust the
Standby Mode
settings in the projector's Extended menu.
Note:
The projector's built-in speaker system is disabled when you connect external speakers.
Note:
You can also connect the projector to an amplifier with speakers.
1.
Make sure your computer or video source is connected to the projector with both audio and video cables as necessary.
2.
Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pinjack cable, or another type of cable or adapter.
3.
Connect one end of the cable to your external speakers as necessary.
46
4.
Connect the stereo mini-jack end of the cable to your projector's
Audio Out
port.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Connecting to External USB Devices
Follow the instructions in these sections to connect external USB devices to the projector.
Connecting a USB Device to the Control Pad or Projector
Selecting the Connected USB Source
Disconnecting a USB Device From the Control Pad or Projector
Connecting to a Document Camera
Parent topic:
USB Device Projection
You can project images and other content without using a computer or video device by connecting any of these devices to your projector or to the control pad:
• USB flash drive
• Digital camera or smartphone
• USB hard drive
• Multimedia storage viewer
• USB memory card reader
47
Note:
Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices, and must be USB Mass Storage Class-compliant.
Note:
USB hard drives must meet these requirements:
• USB Mass Storage Class-compliant (not all USB Mass Storage Class devices are supported)
• Formatted in FAT or FAT32
• Self-powered by their own AC power supplies (Bus-powered hard drives are not recommended)
• Avoid using hard drives with multiple partitions
You can also use the EasyMP PC Free feature to create your own slide shows containing converted
PowerPoint files and image files, and project them from a connected USB device or memory card reader.
Parent topic:
Connecting to External USB Devices
Related topics
Projecting a PC Free Presentation
Connecting a USB Device to the Control Pad or Projector
You can connect your USB device to the
USB-A
port on the control pad or projector and use it to project images and other content.
1.
If your USB device came with a power adapter, plug the device into an electrical outlet.
2.
Make sure a USB cable is connected between the
USB-A
port on the projector and the
USB-B
port on the control pad.
3.
Connect the USB cable for the device (or USB flash drive or USB memory card reader) into the
USB-A
port on the bottom of the control pad.
48
4.
Connect the other end of the cable (if applicable) to your device.
Note:
You can also connect a USB device directly to the projector's
USB-A
port.
Parent topic:
Connecting to External USB Devices
Related topics
Projecting a PC Free Presentation
Selecting the Connected USB Source
You can switch the projector's display to the source you connected to the
USB-A
port on the control pad or the projector.
1.
Make sure the connected USB source is turned on, if necessary.
2.
Press the
Source Search
button on the remote control or control pad, then select
USB1
.
Parent topic:
Connecting to External USB Devices
Disconnecting a USB Device From the Control Pad or Projector
When you finish presenting with a connected USB device, you must prepare to disconnect the device from the control pad or projector.
1.
If the device has a power button, turn off and unplug the device.
2.
Disconnect the USB device (or cable) from the control pad or projector.
Parent topic:
Connecting to External USB Devices
Connecting to a Document Camera
You can connect the Epson DC-06 document camera to your projector's
USB-A
document camera port to project images viewed by the camera.
Note:
For additional features supported by software, connect the Epson DC-06 document camera to your computer instead of the projector. You may be able to connect different Epson document camera models to your projector's
Computer
port. See the document camera's manual for instructions.
1.
Locate the USB cable that came with the document camera.
49
2.
Connect the USB cable to the projector's
USB-A
document camera port.
3.
Connect the other end of the cable to the document camera's USB Type B port.
Parent topic:
Connecting to External USB Devices
Related references
Optional Equipment and Replacement Parts
Connecting a Printer to the Control Pad
You can connect a printer or all-in-one device to the
Printer
port on the control pad and use it to print your projected and annotated content.
Note:
Make sure the printer meets the control command requirements.
1.
Make sure a USB cable is connected between the
USB-A
port on the projector and the
USB-B
port on the control pad.
2.
Connect another USB cable to the
Printer
port on the control pad. Make sure the cable is no longer than 16.4 ft (5 m).
50
3.
Connect the other end of the cable to the USB type B port on the printer.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
Caution:
Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
1.
Open the battery cover.
51
2.
Insert the batteries with the
+
and
–
ends facing as shown.
3.
Close the battery cover and press it down until it clicks into place.
Warning:
Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic:
Installing Batteries in the Pens
Each pen uses one AA battery.
52
1.
Open the battery cover as shown.
2.
Insert the battery with the
+
and
–
ends facing as shown.
3.
Replace the battery cover and press it down until it clicks into place.
Parent topic:
Installing Batteries in the Control Pad
The control pad uses two AA batteries.
53
Note:
If you have the optional remote control cable set (ELPKC28), you can use it instead of batteries to power the control pad.
1.
Remove the top cover of the control pad by prying it off as shown.
2.
Insert the batteries with the
+
and
–
ends facing as shown.
54
3.
Replace the cover and press it down until it clicks into place.
Parent topic:
Related references
Optional Equipment and Replacement Parts
55
Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Connecting to a Network Projector in Windows
Controlling a Networked Projector Using a Web Browser
Adding Templates from a Web Browser
Registering a Digital Certificate on the Projector
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Network Interactivity
You can use the interactive pens with images projected through a network. Both annotation mode and computer interactive mode are available, even on a wireless connection. You can connect up to 4 projectors at the same time and share one computer image over the network.
You need to use one of the following software applications to use computer interactive mode over a network:
•
EasyMP Network Projection
version 2.81 or later. See the
EasyMP Network Projection Operation
Guide
for instructions.
•
Quick Wireless
version 1.31 or later (Windows only). See the instructions included with the optional
Quick Wireless Connection USB Key.
With either application, you need to select
Use Interactive Pen
on the
General settings
tab and
Transfer layered windows
on the
Adjust performance
settings tab.
If you want to annotate when using computer interactive mode over a network, you need use Easy
Interactive Tools (or another annotation program). You can install Easy Interactive Tools from the CD labeled "Epson Projector Software for Easy Interactive Function." You can also download the software from the Epson website.
In Windows 7 and Windows Vista, you can also use the utility program called "Connect to a Network
Projector." This utility is part of the Windows operating system, and does not require any additional software. You can connect one projector to the computer and annotate on your projected image. You cannot use the pen as a mouse.
56
Note the following restrictions on network interactivity:
• Pen response may be slower over the network.
• You can only use one pen at a time.
Parent topic:
Using the Projector on a Network
Related tasks
Connecting to a Network Projector in Windows
Wired Network Projection
You can send images to your projector through a wired network. To do this, you connect the projector to your network, and then set up your projector and computer for network projection.
After connecting and setting up the projector as described here, install the network software from the
Epson Projector Software
CD-ROM on your computer. Use the following software and documentation to set up, control, and monitor network projection:
•
EasyMP Network Projection
software sets up your computer for network projection. See the
EasyMP Network Projection Operation Guide
for instructions.
•
EasyMP Monitor
software (Windows only) lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your projector.
•
Connect to a Network Projector
(Windows 7 and Windows Vista only)
Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly using the EasyMP Network Projection software.
Selecting Wired Network Settings
Parent topic:
Using the Projector on a Network
Connecting to a Wired Network
To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network cable. To ensure proper data transmission, use a Category 5 shielded cable or better.
1.
Connect one end of the network cable to your network hub, switch, or router.
57
2.
Connect the other end of the cable to the projector's
LAN
port.
Parent topic:
Selecting Wired Network Settings
Before you can project from computers on your network, you must select the network settings for the projector using its menu system.
Note:
Make sure you already connected the projector to your wired network using the
LAN
port.
1.
Turn on the projector.
2.
Press the
Menu
button.
58
3.
Select the
Network
menu and press
Enter
.
4.
Select
Network Configuration
and press
Enter
.
5.
Select the
Basic
menu and press
Enter
.
59
6.
Select the following basic options as necessary:
•
Projector Name
lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
•
Web Remote Password
lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
•
Projector Keyword
lets you turn on a security password to prevent access to the projector by anyone not in the room with it. You must enter a displayed, randomized keyword from a computer using the EasyMP Network Projection software to access the projector.
Note:
Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press
Enter
to select them.
7.
Select the
Wired LAN
menu and press
Enter
.
8.
Select your IP Settings as necessary:
• If your network assigns addresses automatically, turn on the
DHCP
setting.
60
• If you must set addresses manually, turn off
DHCP
and enter the projector's
IP Address
,
Subnet
Mask
, and
Gateway Address
as needed.
Note:
To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press
Enter
.
9.
Specify a
WINS server
address for saving images if necessary.
10. To prevent display of the IP address on the standby screen, turn off
IP Address Display
.
11. When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Connecting to a Network Projector in Windows
In Windows 7 and Windows Vista, you can use the utility program called "Connect to a Network
Projector." This allows you to project over a wired or wireless network without installing additional software. You can use the projector's internal toolbar (annotation mode) to add notes and print or capture your projected content.
1.
Make sure the projector and computer are connected to the same network.
2.
Turn on the projector and select the LAN source.
3.
Select
> All Programs > Accessories > Connect to a Network Projector
.
4.
Follow the instructions on the screen to select the projector and connect.
5.
If necessary, use the pen to select the , , or icon and display the annotation toolbar.
Note:
If you switch to whiteboard mode and then want to switch back to your computer display, you will have to reconnect to the projector.
Parent topic:
Using the Projector on a Network
Wireless Network Projection
You can send images to your projector through a wireless network. To do this, you must install the optional Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection.
61
Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly using the EasyMP Network Projection software.
There are two ways to connect the projector to your wireless network:
• Using the optional Quick Wireless Connection USB Key (Windows only)
• Configuring the connection manually using the projector's
Network
menus
After installing the module and setting up the projector, install the network software from the
Epson
Projector Software
CD on your computer. Use the following software and documentation to set up, control, and monitor wireless projection:
•
EasyMP Network Projection
software sets up your computer for wireless network projection. See the
EasyMP Network Projection Operation Guide
for instructions.
•
EasyMP Monitor
software (Windows only) lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your projector.
Installing the Wireless LAN Module
Using Quick Wireless Connection (Windows Only)
Selecting Wireless Network Settings Manually
Searching for a Wireless Network
Selecting Wireless Network Settings in Windows
Selecting Wireless Network Settings in Mac OS X
Parent topic:
Using the Projector on a Network
Related references
Optional Equipment and Replacement Parts
Installing the Wireless LAN Module
To use the projector over a wireless network, install the Epson 802.11b/g/n wireless module in the projector. Do not install any other type of wireless module.
Caution:
Never remove the module while its indicator light is green or flashing, or while you are projecting wirelessly. You may damage the module or lose data.
1.
Turn off the projector and unplug the power cord.
62
2.
Unscrew and remove the cable cover if it is attached (screwdriver not included).
3.
Insert the wireless LAN module into the port.
4.
Replace the cable cover and tighten the screws.
5.
Plug in and turn on the projector.
Parent topic:
63
Using Quick Wireless Connection (Windows Only)
You can use the optional Quick Wireless Connection USB Key to quickly connect the projector to a
Windows computer wirelessly. Then you can project your presentation and remove the key when you are done.
1.
Turn on the projector.
2.
Connect the USB key to the projector's
USB-A
port.
Note:
If the control pad is connected to the projector, you can also connect the USB key to the
USB-
A
port on the control pad, as shown:
You see a projected message that the network information update is complete.
3.
Remove the USB key.
64
4.
Now connect the USB key to a USB port on your computer or notebook.
Note:
In Windows Vista, if you see the AutoPlay window, select
Run LaunchU3.exe
, then select
Allow
on the next screen.
5.
Follow the on-screen instructions to install the Quick Wireless Connection driver.
Note:
If you see a Windows Firewall message, click
Yes
to disable the firewall.
After a few minutes, your computer image is displayed by the projector. If it does not appear, press the
Source Search
button on your projector remote control and select the
LAN
source, or restart your computer.
6.
Run your presentation as necessary.
7.
When you finish projecting wirelessly, remove the USB key from your computer.
Note:
You may need to restart your computer to reactivate your wireless LAN connection.
Parent topic:
Related references
Optional Equipment and Replacement Parts
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you must select the network settings for the projector using its menu system.
1.
Turn on the projector.
2.
Press the
Menu
button.
65
3.
Select the
Network
menu and press
Enter
.
4.
Select
Network Configuration
and press
Enter
.
5.
Select the
Basic
menu and press
Enter
.
66
6.
Select the following basic options as necessary:
•
Projector Name
lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
•
Web Remote Password
lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web.
•
Projector Keyword
lets you turn on a security password to prevent access to the projector by anyone not in the room with it. You must enter a displayed, randomized keyword from a computer using the EasyMP Network Projection software to access the projector.
Note:
Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow buttons on the remote control to highlight characters and press
Enter
to select them.
7.
Select the
Wireless LAN
menu and press
Enter
.
8.
Select the settings on the Wireless LAN menu as necessary for your network.
9.
When you finish selecting settings, select
Setup complete
and follow the on-screen instructions to save your settings and exit the menus.
After you complete the wireless settings for your projector, you need to select the wireless network on your computer.
67
Parent topic:
Wireless LAN Menu Settings
Note:
See your projector's
EasyMP Network Projection Operation Guide
for details on selecting these settings.
Setting
Wireless LAN Power
Wi-Fi Protected Setup
Wireless LAN System
Connection Mode
SSID Auto Setting
SSID
Options
On
Off
To Setup Wizard
Description
Turns on wireless LAN support
802.11b/g
802.11b/g/n
Quick
Advanced
Select
To Setup Wizard
to start the WPS Connection Setup utility
Sets the type of wireless LAN system the projector is connecting to
Selects the type of wireless connection:
Quick
: lets you quickly connect to one computer or use the optional Quick Wireless
Connection USB key to connect
Advanced
: lets you connect to multiple computers via a wireless network access point
On
Off
Turns on automatic SSID searching in
Quick
connection mode; set to
Off
when connecting to multiple projectors at the same time
Up 32 alphanumeric characters Sets the SSID (network name) of the wireless LAN system the projector is connecting to
68
Setting
Search Access Point
Channel
SSID Display
DHCP
WINS server
IP Address Display
Options
To Search View
1ch
6ch
11ch
On
Off
On
Off
IP address
On
Off
Description
Search for available wireless network access points in
Advanced
connection mode
In
Quick
connection mode, selects the frequency band
(channel) used by the wireless
LAN
Selects whether to display the
SSID on the network standby screen
Turns on DHCP if your network assigns addresses automatically; set to
Off
to manually enter the network's
IP Address
,
Subnet
Mask
, and
Gateway Address
Sets the IP address for the network folder where images are saved; this setting is used
(instead of the UNC address) when the folder is on a different network segment from the projector
Selects whether to display the IP address on the network standby screen
Parent topic:
Selecting Wireless Network Settings Manually
Searching for a Wireless Network
You can use your projector's site survey function to quickly locate and connect to available wireless networks.
1.
Turn on the projector.
2.
Press the
Menu
button on the remote control.
69
3.
Select the
Network
menu and press
Enter
.
4.
Select
Network Configuration
and press
Enter
.
5.
Select the
Wireless LAN
menu and press
Enter
.
6.
Select
Advanced
as the Connection mode and press
Enter
.
70
7.
Select
To Search View
and press
Enter
.
8.
Select the name of the wireless network you want to connect to and press
Enter
.
71
9.
Select a
WPA
or
EAP
setting from the drop-down menu.
10. Select the settings on the security menu as necessary for your network.
11. When you finish selecting settings, select
Setup complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Selecting Wireless Network Settings in Windows
Before connecting to the projector, select the correct wireless network on your computer.
1.
To access your wireless utility software, double-click the network icon on the Windows taskbar.
2.
Do one of the following:
• If your projector is set up on an existing network (Advanced mode), select the network name
(SSID).
• If your projector is configured for Quick mode, select the SSID you assigned to the projector.
3.
Click
Connect
.
Parent topic:
Selecting Wireless Network Settings in Mac OS X
Before connecting to the projector, select the correct wireless network in Mac OS X.
1.
Click the AirPort icon on the menu bar at the top of the screen.
2.
Make sure AirPort is turned on, then do one of the following:
• If your projector is set up on an existing network (Advanced mode), select the network name
(SSID).
• If your projector is configured for Quick mode, select the SSID you assigned to the projector.
Parent topic:
Enabling WPA or EAP Security
Set up the WPA or EAP security settings to match your network's settings. Check with your network administrator for guidance on entering the correct information.
72
1.
Select a
WPA
or
EAP
setting from the drop-down menu.
2.
Select the settings on the security menu as necessary for your network.
3.
When you finish selecting settings, select
Setup complete
and follow the on-screen instructions to save your settings and exit the menus.
Wireless Security Menu Settings
Parent topic:
Wireless Security Menu Settings
Settings on the Security menu let you select the type of security and security settings that match the network you are connecting the projector to.
Setting
Security
Passphrase
Options
Open
WPA2-PSK(AES)
WPA/WPA2-EAP
Description
Selects the type of security used on the wireless network
Various passphrases from 8 to For WPA-2-PSK security, selects
32 characters the pre-shared passphrase used on the network
73
Setting
EAP Method
Options
PEAP
PEAP-TLS
EAP-TLS
EAP-Fast
LEAP
Various user names up to 32 characters
Description
For WPA/WPA2-EAP security, selects the protocol for authentication
User name
Password
Client Certificate
Verify Server Certificate
Various passwords up to 32 characters
None
On
Off
For WPA/WPA2-EAP security, selects the user name; automatically detected when using the
PEAP-TLS
or
EAP-
TLS
EAP methods
For WPA/WPA2-EAP security, selects the password for EAP authentication
For WPA/WPA2-EAP security, displays the certificate's
Issued to
,
Issued by
, and
Validity period
if a client certificate has been set
For WPA/WPA2-EAP security, selects whether to verify the server certificate when a CA certificate has been set
CA certificate
Setting RADIUS Server Name
RADIUS Server Name
None
On
Off
For WPA/WPA2-EAP security, displays the certificate's
Issued to
,
Issued by
, and
Validity period
if a CA certificate has been set
For WPA/WPA2-EAP security, selects whether to verify the authentication server name during certificate verification
Various server names up to 32 For WPA/WPA2-EAP security, characters selects the server name to verify
74
Setting Options
Verify Exp. date of Server Cert. On
Off
Description
For WPA/WPA2-EAP security, selects whether to verify the server certificate's validity period during certificate verification
Parent topic:
Controlling a Networked Projector Using a Web Browser
Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely.
Note:
The web setup and control features support Microsoft Internet Explorer 8.0 or later, and Safari on networks that do not use a proxy server for connection. You cannot select all of the projector menu settings or control all projector functions using a web browser.
Note:
If you want to use a web browser to select settings when the projector is turned off, you need to adjust the
Standby Mode
settings in the Extended menu.
1.
Make sure the projector is turned on.
2.
Start your web browser on a computer connected to the network.
3.
Type the projector's IP address into the browser's address box and press the computer's
Enter
key.
You see the Web Control screen and a prompt to enter a user ID and password.
4.
Enter the following information in uppercase or lowercase letters, exactly as shown:
• For the user ID, enter
EPSONWEB
. (You cannot change the user ID.)
• For the password, enter the default password
admin
. (You can change the Web Control password using the projector's Network menu.)
5.
To select projector menu settings, select the name of the menu and follow the on-screen instructions to select settings.
6.
To control projection remotely, select the
Web Remote
option.
You see this screen:
75
1 Power button control
2 Captures the projected image. Switch to whiteboard mode to paste the image into a new page.
3 Prints the projected image.
4
Freeze
button control
5
A/V Mute
button control
6
Page Up
and
Page Down
button controls
7 Searches for sources
8 Switches to whiteboard mode.
9 Saves the projected image in .png format.
10
Volume
button controls
11 Closed Caption control
7.
Select the icon corresponding to the projector function you want to control.
Parent topic:
Using the Projector on a Network
Related references
Projector Setup Settings - Extended Menu
76
Adding Templates from a Web Browser
You can use a web browser to add templates for use in Whiteboard mode. You can add up to 5 images, which must be in .png format to be used as templates.
1.
Make sure the projector is turned on.
2.
Start your web browser on a computer connected to the network.
3.
Type the projector's IP address into the browser's address box and press the computer's
Enter
key.
You see the Web Control screen and a prompt to enter a user ID and password.
4.
Enter the following information in uppercase or lowercase letters, exactly as shown:
• For the user ID, enter
EPSONWEB
. (You cannot change the user ID.)
• For the password, enter the default password
admin
. (You can change the Web Control password using the projector's Network menu.)
5.
Under
Whiteboard Settings
, select
Administrator Settings
.
You see a screen like this:
6.
Under
Template Settings
, select the number of the template you are uploading.
7.
Select the
Browse
button, select the .png image on your computer, and select
Open
.
8.
Select
Set
to upload the template to the projector.
77
Parent topic:
Using the Projector on a Network
Related tasks
Selecting Background Templates
Registering a Digital Certificate on the Projector
Follow the instructions here if you need to install a digital certificate on the projector to provide security for your presentation files.
Note:
You can register a digital certificate over a network or from a connected USB device. However, be sure to register just once from either a USB device or network, or the certificate may not install correctly.
Registering Digital Certificates from a Web Browser
Parent topic:
Using the Projector on a Network
Secure HTTP
You can use the HTTPS protocol to increase security between the projector and a web browser communicating with it. To do this, you create a server certificate, install it on the projector, and turn on the
Secure HTTP
setting in the projector menus to verify the reliability of the web browser.
Even if you do not install a server certificate, the projector automatically creates a self-signed certificate and allows communication. However, because the self-signed certificate cannot verify reliability from a web browser, you see a warning about the server's reliability when you access the projector from a web browser. This warning does not prevent communication.
Parent topic:
Registering a Digital Certificate on the Projector
Registering Digital Certificates from a Web Browser
You can register the digital certificates on the projector for wireless LAN authentication.
1.
Make sure your digital certificate file is compatible with projector registration.
2.
Make sure the projector is turned on.
3.
Start your web browser on a computer connected to the network.
4.
Type the projector's IP address into the browser's address box and press the computer's
Enter
key.
You see the Web Control screen and a prompt to enter a user ID and password.
78
5.
Enter the following information in uppercase or lowercase letters, exactly as shown:
• For the user ID, enter
EPSONWEB
. (You cannot change the user ID.)
• For the password, enter the default password
admin
. (You can change the Web Control password using the projector's Network menu.)
6.
Under
Network
, select the
Administrator Settings
option and select
Manage Certificates
.
You see a screen like this:
7.
Click the
Browse
button, select the certificate file, and click
Open
.
8.
Enter a password in the
Password
box.
9.
Click
Set
to adjust the certificate validity period.
10. When you finish registering the certificate, click
Apply
to finalize your changes and complete the registration.
Digital Certificate Types for Registration via Web Control
Parent topic:
Registering a Digital Certificate on the Projector
Digital Certificate Types for Registration via Web Control
You can register these types of digital certificates using the projector's Web Control feature.
Client Certificate (PEAP-TLS/EAP-TLS)
79
Specification
Format
Extension
Encryption
Hashes
Key length
Password
Description
PKCS#12
PKCS, P12
RSA
MD5/SHA-1/SHA-256/SHA-384/SHA-512
512/1024/2048/4096 bit
Up to 32 alphanumeric characters; required
Server Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-Fast)
Specification
Format
Extension
Encryption
Hashes
Key length
Encoding
Description
X509v3
DER/CER/PEM
RSA
MD5/SHA-1/SHA-256/SHA-384/SHA-512
512/1024/2048/4096 bit
BASE64/Binary
Web Server Certificate (Secure HTTP)
Specification
Format
Extension
Encryption
Hashes
Key length
Common name
Organization
Password
Description
PKCS#12
PKCS, P12
RSA
MD5/SHA-1/SHA-256/SHA-384/SHA-512
512/1024/2048/4096 bit
Network host name
Optional
Up to 32 alphanumeric characters; required
80
Parent topic:
Registering Digital Certificates from a Web Browser
Setting Up Projector Network E-Mail Alerts
You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector.
1.
Press the
Menu
button.
2.
Select the
Network
menu and press
Enter
.
3.
Select
Network Configuration
and press
Enter
.
4.
Select the
Administrator Settings
menu and press
Enter
, then select
Mail Notification
and press
Enter
.
5.
Enter the IP address for the
SMTP Server
option.
Note:
Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
6.
Select a number for the SMTP server
Port Number
, from 1 to 65535 (default is 25).
81
7.
Choose an
Email Address
field, enter the e-mail address, and select the alerts you want to receive there. Repeat for up to three addresses.
Note:
Your e-mail address can be up to 32 alphanumeric characters long.
8.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Note:
If a critical problem causes the projector to shut down, you may not receive an e-mail alert.
Network Projector E-mail Alert Messages
Parent topic:
Using the Projector on a Network
Network Projector E-mail Alert Messages
When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you receive an e-mail containing the following information:
•
Epson Projector
on the subject line
• The name of the projector experiencing a problem
• The IP address of the affected projector
• Detailed information about the problem
Note:
If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Parent topic:
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Network administrators can install SNMP (Simple Network Management Protocol) software on network computers so they can monitor projectors. If your network uses this software, you can set up the projector for SNMP monitoring.
1.
Press the
Menu
button.
2.
Select the
Network
menu and press
Enter
.
3.
Select
Network Configuration
and press
Enter
.
82
4.
Select the
Administrator Setting
menu and press
Enter
, then select the
SNMP
menu and press
Enter
.
5.
Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field.
Note:
Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255).
6.
Enter the community name of SNMP (up to 32 single-byte alphanumeric characters).
7.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Using the Projector on a Network
Crestron RoomView Support
If you are using the Crestron RoomView network monitoring and control system, you can set up your projector for use on the system. Crestron RoomView lets you control and monitor your projector using a web browser.
Note:
You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP
Monitor when you use Crestron RoomView.
83
For additional information on Crestron RoomView, contact Crestron.
Setting Up Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView
Parent topic:
Using the Projector on a Network
Setting Up Crestron RoomView Support
To set up your projector for monitoring and control using a Crestron RoomView system, make sure your computer and projector are connected to the network. If you are connecting wirelessly, set up the projector using the Advanced network connection mode.
Note:
If you want to use the Crestron RoomView system when the projector is turned off, you need to adjust the
Standby Mode
settings in the Extended menu.
1.
Press the
Menu
button.
2.
Select the
Network
menu and press
Enter
.
3.
Select
Network Configuration
and press
Enter
.
4.
Select the
Administrator Setting
menu and press
Enter
.
5.
Set the
Crestron RoomView
setting to
On
to allow the projector to be detected.
84
6.
When you finish selecting settings, select
Complete
or
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
7.
Turn off the projector, then turn it on again to enable the setting.
Parent topic:
Controlling a Networked Projector Using Crestron RoomView
Once you have set up your projector to use Crestron RoomView, you can control and monitor projection using a compatible web browser.
1.
Start your web browser on a computer connected to the network.
2.
Type the projector's IP address into the browser's address box and press the computer's
Enter
key.
You see this screen:
3.
Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box.
4.
To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons. You can scroll through button options at the bottom of the screen.
Note:
These on-screen buttons do not directly correspond to the projector's remote control buttons:
•
OK
acts as the
Enter
button
•
Menu
displays the projector's menu
85
5.
To view information about the projector, click the
Info
tab.
6.
To change projector, Crestron, and password settings, click the
Tools
tab, select settings on the displayed screen, and click
Send
.
7.
When you finish selecting settings, click
Exit
to exit the program.
Parent topic:
86
Using Basic Projector Features
Follow the instructions in these sections to use your projector's basic features.
Selecting the Language for the Projector Menus
Resizing the Image with the Wide and Tele Buttons
Controlling the Volume with the Volume Buttons
Projecting a PC Free Presentation
Turning On the Projector
Turn on the computer or video equipment you want to use before you turn on the projector so it can display the image source.
Note:
For whiteboard mode, you do not need an image source.
1.
Connect the power cord to the projector's power inlet.
2.
Plug the power cord into an electrical outlet.
The projector's power light turns orange. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode).
Note:
With Direct Power On turned on, the projector turns on as soon as you plug it in.
3.
Press the power button on the projector, remote control, or control pad to turn on the projector.
87
The projector beeps and the power light flashes green as the projector warms up. After about 30 seconds, the power light stops flashing and turns green.
Warning:
Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children and pets.
If you do not see a projected image right away, try the following:
• Turn on the connected computer or video device.
• Insert a DVD or other video media, and press the play button (if necessary).
• Press the
Source Search
button on the projector or remote control (or control pad) to detect the video source.
Parent topic:
Using Basic Projector Features
Turning Off the Projector
Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
Note:
Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
1.
Press the power button on the projector or the remote control (or control pad).
The projector displays a shutdown confirmation screen.
2.
Press the power button again. (To leave it on, press any other button.)
The projector beeps twice, the lamp turns off, and the power light turns orange.
Note:
With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away (if necessary).
88
Caution:
Do not turn the projector on immediately after turning it off. Turning the projector on and off frequently may shorten the life of the lamp.
3.
To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord.
Caution:
To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange.
Parent topic:
Using Basic Projector Features
Selecting the Language for the Projector Menus
If you want to view the projector's menus and messages in another language, you can change the
Language setting.
1.
Turn on the projector.
2.
Press the
Menu
button.
3.
Select the
Extended
menu and press
Enter
.
4.
Select the
Language
setting and press
Enter
.
5.
Select the language you want to use and press
Enter
.
6.
Press
Menu
or
Esc
to exit the menus.
89
Parent topic:
Using Basic Projector Features
Adjusting the Image Height
If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. Make sure the feet have been installed.
Caution:
Tilting the projector will distort the image shape and may cause difficulty focusing the image.
Do not tilt the projector at an angle of more than 1.5º.
1.
Turn on the projector and display an image.
2.
To raise the image, extend the rear feet by rotating them.
3.
To lower the image, extend the front foot by rotating it.
90
4.
If the image is tilted, rotate the rear feet to adjust their height.
If the projected image is unevenly rectangular, you need to adjust the image shape.
Parent topic:
Using Basic Projector Features
Related concepts
Related references
Projector Setup Settings - Extended Menu
Image Shape
You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
Correcting Image Shape with the Keystone Buttons
Correcting Image Shape with Quick Corner
Parent topic:
Using Basic Projector Features
Correcting Image Shape with the Keystone Buttons
You can use the projector's keystone correction buttons to correct the shape of an image that is unevenly rectangular on the sides.
91
Note:
The horizontal and vertical correction angle should be no more than ± 3º, with keystone correction up to ± 6.
1.
Turn on the projector and display an image.
Note:
You can display a pattern to aid in adjusting the projected image using the Settings menu.
2.
Press one of these keystone buttons on the control panel to display the Keystone adjustment screen.
3.
Press a keystone button on the projector's control panel to adjust the image shape.
92
Note:
The horizontal keystone adjustment buttons are labeled
Wide
and
Tele
.
After correction, your image is slightly smaller.
Note:
If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus.
Parent topic:
Related references
Projector Feature Settings - Settings Menu
Correcting Image Shape with Quick Corner
You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular on all sides.
1.
Turn on the projector and display an image.
Note:
You can display a pattern to aid in adjusting the projected image using the Settings menu.
2.
Press the
Menu
button.
93
3.
Select the
Settings
menu and press
Enter
.
4.
Select the
Keystone
setting and press
Enter
.
5.
Select the
Quick Corner
setting and press
Enter
. Then press
Enter
again.
You see the Quick Corner adjustment screen.
94
6.
Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press
Enter
.
7.
Press the arrow buttons to adjust the image shape as necessary.
8.
When you are finished, press
Esc
.
95
Parent topic:
Resizing the Image with the Wide and Tele Buttons
1.
Turn on the projector and display an image.
2.
To enlarge the image size, press the
Wide
button on the projector's control panel.
3.
To reduce the image size, press the
Tele
button.
After you adjust the image size, the Image Shift screen is displayed automatically.
Note:
If the projector is installed out of reach, you can also adjust the image size with the remote control using the Zoom setting in the projector menus.
Parent topic:
Using Basic Projector Features
Related references
Projector Feature Settings - Settings Menu
Adjusting the Image Position
You can use the Image Shift feature to adjust the image position without moving the projector.
96
1.
Turn on the projector and display an image.
2.
Adjust the image size using the
Wide
and
Tele
buttons.
After you adjust the image size, the Image Shift screen is displayed automatically.
3.
Use the arrow buttons on the projector or remote control to adjust the image position.
Note:
You can also use the Settings menu to adjust the
Image Shift
.
Parent topic:
Using Basic Projector Features
Related references
Projector Feature Settings - Settings Menu
97
Focusing the Image
1.
Turn on the projector and display an image.
Note:
You can display a pattern to aid in adjusting the projected image using the Settings menu.
2.
Slide the switch to open the air filter cover on the side of the projector.
3.
Raise or lower the focus lever to sharpen the image.
Parent topic:
Using Basic Projector Features
Related references
Projector Feature Settings - Settings Menu
Remote Control Operation
The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen or board, or the front or back of the projector.
Make sure that you aim the remote control at the projector's receivers within the angles listed here.
98
1 19.7 feet (6 m)
2 ± 30º
3 ± 55º
4 ± 60º
5 ± 15º
Note:
Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Using the Remote Control as a Wireless Mouse
Using the Remote Control as a Pointer
Parent topic:
Using Basic Projector Features
Related tasks
Replacing the Remote Control Batteries
99
Using the Remote Control as a Wireless Mouse
You can use the projector's remote control as a wireless mouse so you can control projection at a distance from the computer.
Note:
This feature cannot be used at the same time as the interactive pens. If you want to use the remote control as a wireless mouse, you need to change the
USB Type B
setting in the projector's
Extended menu.
1.
Connect the projector to a computer using the projector's
USB-B
,
Computer
,
HDMI
, or
DisplayPort
port to display video.
2.
If you connected your computer to the
Computer
,
HDMI
, or
DisplayPort
port, also connect a USB cable to the projector's
USB-B
port and to a USB port on your computer (for wireless mouse support).
3.
Start your presentation.
4.
Use the following buttons on the remote control to control your presentation:
• To move through slides or pages, press the up or down
Page
buttons.
• To move the cursor on the screen, use the arrow buttons.
• To left-click, press the button once (press it twice to double-click).
• To right-click, press the
Esc
button.
• To drag-and-drop, hold the button as you move the cursor with the arrow buttons, then release at the destination.
Parent topic:
100
Related references
Projector Setup Settings - Extended Menu
Using the Remote Control as a Pointer
You can use the projector's remote control as a pointer to help you call out important information on the screen. The default pointer shape is an arrow, but you can select an alternative shape using the Settings menu.
1.
Press the
Pointer
button on the remote control.
2.
Use the arrow buttons on the remote control to move the pointer on the screen.
3.
Press
Esc
to clear the pointer from the screen.
Parent topic:
Related references
Projector Feature Settings - Settings Menu
Selecting an Image Source
If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
101
1.
Make sure the connected image source you want to use is turned on.
2.
For video image sources, insert a DVD or other video media and press its play button (if necessary).
3.
Press the
Source Search
button on the projector, remote control, or control pad, then select the source you want.
102
Parent topic:
Using Basic Projector Features
Projection Modes
Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly.
•
Front/Upside Down
(default setting) flips the image over top-to-bottom to project upside-down from a wall or ceiling mount. This mode should also be used when you mount the projector vertically on a table to create an interactive work surface.
•
Front
lets you project from a table in front of the screen.
•
Rear/Upside Down
flips the image over top-to-bottom and horizontally to project from the wall or ceiling and behind a translucent screen.
•
Rear
flips the image horizontally to project from behind a translucent screen.
Note:
The two Rear modes cannot be used with the interactive pens.
You can change the projection mode using the remote control or by changing the
Projection
setting in the
Extended
menu.
Changing the Projection Mode Using the Remote Control
Changing the Projection Mode Using the Menus
Parent topic:
Using Basic Projector Features
Changing the Projection Mode Using the Remote Control
You can change the projection mode to flip the image over top-to-bottom.
1.
Turn on the projector and display an image.
2.
Hold down the
A/V Mute
button on the remote control for five seconds.
103
The image disappears briefly and reappears flipped top-to-bottom.
3.
To change projection back to the original mode, hold down the
A/V Mute
button for five seconds again.
Parent topic:
Changing the Projection Mode Using the Menus
You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus.
1.
Turn on the projector and display an image.
2.
Press the
Menu
button.
3.
Select the
Extended
menu and press
Enter
.
4.
Select the
Projection
setting and press
Enter
.
5.
Select a projection mode and press
Enter
.
6.
Press
Menu
or
Esc
to exit the menus.
Parent topic:
104
Image Aspect Ratio
The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.
If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Changing the Image Aspect Ratio
Parent topic:
Using Basic Projector Features
Related references
Input Signal Settings - Signal Menu
Changing the Image Aspect Ratio
You can change the aspect ratio of the displayed image to resize it.
1.
Turn on the projector and switch to the image source you want to use.
2.
Press the
Aspect
button on the remote control.
The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen.
3.
To cycle through the available aspect ratios for your input signal, press the
Aspect
button repeatedly.
Note:
To display 4:3 images without black bars, you can use the Signal menu to select
Normal
for the
Resolution
setting.
105
Parent topic:
Available Image Aspect Ratios
You can select the following image aspect ratios, depending on the input signal from your image source.
Note:
Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal.
Aspect ratio setting
Auto
Normal
16:9
Full
Zoom
Native
Description
Automatically sets the aspect ratio according to the input signal and the
Resolution
setting.
Displays images using the full projection area and maintains the aspect ratio of the image.
Converts the aspect ratio of the image to 16:9.
Displays images using the full width of the projection area, but does not maintain the aspect ratio.
Displays images using the full width of the projection area and maintains the aspect ratio of the image.
Displays images as is (aspect ratio and resolution are maintained).
Note:
The
Auto
aspect ratio setting is available only for HDMI image sources.
Parent topic:
Color Mode
The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select a mode designed to match your image and environment, or experiment with the available modes.
If you always want to use a particular color mode for a certain video input source, you can select it using the projector menus.
106
Parent topic:
Using Basic Projector Features
Changing the Color Mode
You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment.
1.
Turn on the projector and switch to the image source you want to use.
2.
If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary.
3.
Press the
Color Mode
button on the remote control to change the Color Mode.
The image appearance changes and the name of the Color Mode appears briefly on the screen.
4.
To cycle through all the available Color Modes for your input signal, press the
Color Mode
button repeatedly.
Parent topic:
Available Color Modes
You can set the projector to use these Color Modes, depending on the input source you are using:
Color Mode
Dynamic
Presentation
Theatre
Photo
Sports
Description
Best for video games in a bright room
Best for color presentations in a bright room
Best for movies projected in a dark room
Best for still images projected in a bright room
Best for television images in a bright room
107
Color Mode sRGB
Blackboard
Whiteboard
DICOM SIM
Customized
Description
Best for standard sRGB computer displays
Best for presentations onto a green chalkboard (adjusts the colors accordingly)
Best for presentations onto a whiteboard (adjusts the colors accordingly)
Best for projecting X-rays and other medical images (shows clear shadows)
Best for customizing a color mode using manual Color Adjustment settings in the Image menu
Note:
The projector is not a medical device and cannot be used for medical diagnosis.
Parent topic:
Turning On Auto Iris
In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project.
1.
Turn on the projector and switch to the image source you want to use.
2.
Press the
Menu
button.
108
3.
Select the
Image
menu and press
Enter
.
4.
Select the
Auto Iris
setting and select
On
.
Note:
You can turn
Auto Iris
on or off for each Color Mode that supports the feature. You cannot change the
Auto Iris
setting when you are using a
Closed Caption
setting.
5.
Press
Menu
or
Esc
to exit the menus.
Parent topic:
Controlling the Volume with the Volume Buttons
The volume buttons control the projector’s internal speaker system or any external speakers you connected to the projector.
You must adjust the volume separately for each connected input source.
1.
Turn on the projector and start a presentation that includes audio.
109
2.
To lower or raise the volume, press the
Volume
buttons on the remote control.
A volume gauge appears on the screen.
3.
To set the volume to a specific level for an input source, use the projector menus.
Parent topic:
Using Basic Projector Features
Related references
Projector Feature Settings - Settings Menu
Projecting a PC Free Presentation
You can use your projector's
PC Free
feature whenever you connect a USB device that contains compatible presentation files. This lets you quickly and easily display a presentation and control it using the projector's remote control.
Starting a Slide Show or Presentation
Parent topic:
Using Basic Projector Features
Related concepts
Related tasks
Connecting a USB Device to the Control Pad or Projector
Supported PC Free File Types
You can project these types of files using the projector's PC Free feature.
Note:
For best results, place your files on media that is formatted in FAT16/32. If you have trouble projecting from media formatted for non-Windows file systems, try formatting the media for Windows
110
instead. You may not be able to use the security features on certain USB storage devices with PC Free features.
Graphic and Text File Formats
File contents File type
(extension)
Image .jpg
Scenario
.bmp
.gif
.png
.fse
.sit
Details
Make sure the file is not:
• CMYK format
• Progressive format
• Highly compressed
• Above 8192 × 8192 resolution
• Over 12MB in size
• Named with a .jpeg extension
Make sure the file resolution is not above 2048 × 2048
Make sure the file is not:
• Above 2048 × 2048 resolution
• Animated
Make sure the file resolution is not above 2048 × 2048
Main format for files converted from PowerPoint using EasyMP Slide
Converter
Compressed format for files converted from PowerPoint using
EasyMP Slide Converter (also called scenario files)
Make sure the file is not:
• Saved in PDF version 1.7 or earlier format
• Encrypted
Movie File Formats
111
File type
(extension)
.mpg
Movie codec
MPEG-2
Audio codec Recording quality
MPEG-1 Layer 1/2 Maximum bit rate: 12 Mbps
You can play back audio from Maximum resolution: 1280 ×
MPEG contents.
720
You cannot play back audio from Linear PCM and AC-3 content.
Make sure the file is not named with an .mpeg
extension.
MPEG-4 AAC-LC .mp4
.wmv
.avi
MPEG-4 ASP
MPEG-4 AVC
WMV9
Motion JPEG
WMA
Linear PCM
ADPCM
Note:
For best results, do not use a USB storage device with a slow access speed or the movies may not play back correctly. You cannot project files to which DRM (Digital Rights Management) is applied.
Parent topic:
Projecting a PC Free Presentation
Starting a Slide Show or Presentation
After connecting a USB device to the control pad or projector, you can switch to the USB input source and start your slide show, video, or presentation.
Note:
You can change the
Slideshow
operation options or add special effects by highlighting
Option
at the bottom of the screen and pressing
Enter
.
1.
Change the source to
USB1
.
The
PC Free
screen appears.
112
2.
Do the following as necessary to locate your files:
• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the
Enter
button.
• To move back up a folder level on your device, highlight
Back to Top
and press
Enter
.
• To view additional images in a folder, highlight
Next page
or
Previous page
and press
Enter
.
3.
Do one of the following to start your slide show or presentation:
• To display an individual image, press the arrow buttons to highlight the image and press
Enter
.
(Press the
Esc
button to return to the file list screen.)
• To display a PDF file, press the arrow buttons to highlight the image and press
Enter
. To enlarge the view of a displayed page, press
Enter
again. (Press the
Esc
button to display a menu of pages to select from.)
• To display a presentation from a scenario file, press the arrow buttons to select the scenario file and press
Enter
. (The scenario might open automatically.)
113
• To play a movie, press the arrow buttons to select the movie file and press
Enter
. Press
Enter
again to pause the movie and display a list of other buttons for controlling playback.
Note:
If any file names are longer than 8 characters or include unsupported symbols, the file names may be shortened or changed only in the screen display.
4.
While projecting, use the following commands to control the display as necessary:
• To move to the next or previous image, press the left or right arrow button. To rotate a displayed image, press the up or down arrow button.
• To display the next or previous PDF page, press the up or down arrow button. To rotate a PDF page, press the left or right arrow button.
• To switch screens in a presentation from a scenario file (.fse file type), press one of these buttons on the remote control.
1 Next slide
2 Previous slide
3 Next slide or animation
4 Next slide or animation (animation effects are not played)
5 Previous slide or animation (animation effects are not played)
5.
To stop the display, slide show, or presentation, follow the on-screen instructions or press the
Esc
button.
114
Note:
You cannot do the following while presenting a PDF file from a USB device:
• Release a password
• Display e-signatures, transparent effects, 3D artwork, or comments
• Play multimedia content
Parent topic:
Projecting a PC Free Presentation
Related tasks
Disconnecting a USB Device From the Control Pad or Projector
Slideshow Display Options
You can select these display options when using the projector's Slideshow feature.
Setting
Display Order
Sort Order
Options
Name Order
Date Order
In Ascending
In Descending
115
Description
Displays files in name order
Displays files in date order
Sorts files in first-to-last order
Sorts files in last-to-first order
Setting
Continuous Play
Screen Switching
Time
Options
On
Off
No
1 Second to 60 Seconds
Effect Wipe
Dissolve
Random
Parent topic:
Starting a Slide Show or Presentation
Description
Displays a slide show continuously
Displays a slide show one time through
Does not display the next file automatically
Displays files for the selected time and switches to the next file automatically; high resolution images may switch at a slightly slower rate
Transitions between images with a wipe effect
Transitions between images with a dissolve effect
Transitions between images using a random variety of effects
116
Adjusting Projector Features
Follow the instructions in these sections to use your projector's feature adjustments.
Shutting Off the Picture and Sound Temporarily
Stopping Video Action Temporarily
Zooming Into and Out of Images
Creating a User Pattern to Display
Shutting Off the Picture and Sound Temporarily
You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it.
If you want to display an image such as a company logo or picture when the presentation is stopped, you can set up this feature using the projector's menus.
1.
Press the
A/V Mute
button on the remote control to temporarily stop projection and mute any sound.
2.
To turn the picture and sound back on, press
A/V Mute
again.
Parent topic:
Related tasks
Saving a User's Logo Image to Display
117
Stopping Video Action Temporarily
You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it.
Note:
You can also stop video action using the interactive pens.
1.
Press the
Freeze
button on the remote control to stop the video action.
2.
To restart the video action in progress, press
Freeze
again.
Parent topic:
Zooming Into and Out of Images
You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen.
Note:
You can also zoom into your image using the interactive pens.
118
1.
Press the
E-Zoom +
button on the remote control.
You see a crosshair on the screen indicating the center of the zoom area.
2.
Use the following buttons on the remote control to adjust the zoomed image:
• Use the arrow buttons to position the crosshair in the image area you want to zoom into.
• Press the
E-Zoom +
button repeatedly to zoom into the image area, enlarging it as necessary.
• To pan around the zoomed image area, use the arrow buttons.
• To zoom out of the image, press the
E-Zoom –
button as necessary.
• To return to the original image size, press
Esc
.
Parent topic:
Related tasks
Zooming Images in Whiteboard Mode
Zooming Images in Annotation Mode
Projector Security Features
You can secure your projector to deter theft or prevent unintended use by setting up the following security features:
• Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings.
• Button lock security to block operation of the projector using the buttons on the control panel.
• Security cabling to physically cable the projector in place.
Locking the Projector's Buttons
119
Parent topic:
Password Security Types
You can set up these types of password security using one shared password:
•
Power On Protect
password prevents anyone from using the projector without first entering a password.
•
User's Logo Protect
password prevents anyone from changing the custom screen the projector can display when it turns on or when you use the A/V Mute feature. The presence of the custom screen discourages theft by identifying the projector’s owner.
•
Network Protect
password prevents anyone from changing the network settings in the projector menus .
Selecting Password Security Types
Entering a Password to Use the Projector
Saving a User's Logo Image to Display
Parent topic:
Setting a Password
To use password security, you must set a password.
1.
Hold down the
Freeze
button on the remote control until you see the Password Protect menu. This takes about five seconds.
2.
Press the down arrow to select
Password
and press
Enter
.
You see the prompt "Change the password?".
120
3.
Select
Yes
and press
Enter
.
4.
Hold down the
Num
button on the remote control and use the numeric buttons to set a four-digit password.
The password displays as **** as you enter it. Then you see the confirmation prompt.
5.
Enter the password again.
You see the message "Password accepted."
6.
Press
Esc
to return to the Password Protect menu.
7.
Make a note of the password and keep it in a safe place in case you forget it.
Parent topic:
Selecting Password Security Types
After setting a password, you see the Password Protect menu. Select the password security types you want to use.
121
If you do not see this menu, hold down the
Freeze
button on the remote control for five seconds until the menu appears.
1.
To prevent unauthorized use of the projector, select
Power On Protect
, press
Enter
, select
On
, press
Enter
again, and press
Esc
.
2.
To prevent changes to the User's Logo screen or related display settings, select
User's Logo
Protect
, press
Enter
, select
On
, press
Enter
again, and press
Esc
.
3.
To prevent changes to network settings, select
Network Protect
, press
Enter
, select
On
, press
Enter
again, and press
Esc
.
You can attach the Password Protect sticker to the projector as an additional theft deterrent.
Note:
Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the password required to use the projector.
Parent topic:
Entering a Password to Use the Projector
If a password is set up and a
Power On Protect
password is enabled, you see a prompt to enter a password whenever you turn on the projector.
You must enter the correct password to use the projector.
122
1.
Hold down the
Num
button on the remote control while you enter the password using the numeric buttons.
The password screen closes.
2.
If the password is incorrect, the following may happen:
• You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed.
• If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support. When you contact Epson Support, provide the displayed request code and proof of ownership for assistance in unlocking the projector.
Parent topic:
Related references
Saving a User's Logo Image to Display
You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature). This transferred image is called the User's Logo screen.
The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in identifying the projector's owner to help deter theft. You can prevent changes to the User's Logo by setting up password protection for it.
1.
Display the image you want to project as the User's Logo.
123
2.
Press the
Menu
button, select the
Extended
menu, and press
Enter
.
3.
Select the
User's Logo
setting and press
Enter
.
You see a prompt asking if you want to use the displayed image as a user's logo.
4.
Select
Yes
and press
Enter
.
You see a selection box overlaying your image.
5.
Use the arrow buttons on the remote control to surround the image area you want to use as the
User's Logo and press
Enter
.
You see a prompt asking if you want to select this image area.
6.
Select
Yes
and press
Enter
. (If you want to change the selected area, select
No
, press
Enter
, and repeat the last step.)
You see the User's Logo zoom factor menu.
124
7.
Select a zoom percentage and press
Enter
.
You see a prompt asking if you want to save the image as the User's Logo.
8.
Select
Yes
and press
Enter
.
Note:
It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished.
You see a completion message.
9.
Press
Esc
to exit the message screen.
10. Select the
Extended
menu and press
Enter
.
11. Select
Display
and press
Enter
.
12. Select when you want to display the User's Logo screen:
• To display it whenever there is no input signal, select
Display Background
and set it to
Logo
.
• To display it whenever you turn the projector on, select
Startup Screen
and set it to
On
.
• To display it whenever you press the
A/V Mute
button, select
A/V Mute
and set it to
Logo
.
To prevent anyone from changing the User's Logo settings without first entering a password, set a password and enable User's Logo security.
Parent topic:
Locking the Projector's Buttons
You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button.
125
1.
Press the
Menu
button.
2.
Select the
Settings
menu and press
Enter
.
3.
Select the
Control Panel Lock
setting and press
Enter
.
4.
Select one of these lock types and press
Enter
:
• To lock all of the projector's buttons, select
Full Lock
.
• To lock all buttons except the power button, select
Partial Lock
.
You see a confirmation prompt.
5.
Select
Yes
and press
Enter
.
Unlocking the Projector's Buttons
Parent topic:
Unlocking the Projector's Buttons
If the projector's buttons have been locked, hold the
Enter
button on the projector's control panel for seven seconds to unlock them.
Parent topic:
Locking the Projector's Buttons
Installing a Security Cable
You can install two types of security cables on the projector to deter theft.
126
• Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson.
• Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.
Parent topic:
Creating a User Pattern to Display
You can transfer an image to the projector and then display it as a pattern to aid in presentations when you use the Pattern Display feature. This transferred image is called the User Pattern.
1.
Display the image you want to project as the User Pattern from a connected computer or video source.
127
2.
Press the
Menu
button, select the
Settings
menu, and press
Enter
.
3.
Select the
Pattern
setting and press
Enter
.
4.
Select the
User Pattern
setting and press
Enter
.
You see a prompt asking if you want to use the displayed image as a User Pattern.
5.
Select
Yes
and press
Enter
.
Note:
It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished.
You see a completion message.
6.
Press
Esc
to exit the message screen.
Parent topic:
Related references
Projector Feature Settings - Settings Menu
128
Using the Interactive Pens
Follow the instructions in these sections to use the interactive pens.
Windows Pen Input and Ink Tools
Three Interactive Modes
The BrightLink interactive pens turn any wall into an interactive whiteboard, either with or without a computer. Three interactive modes are available:
• In whiteboard mode, you can use one or both interactive pens to write on the projected "whiteboard."
You can insert images from a thumbdrive or scanner and save, print, or email your "pages," without connecting a computer.
• In annotation mode (PC free annotation), you can add notes to content projected from a computer, tablet, document camera, or other source. You can capture your annotated pages, then save or print them. You can even split the screen and annotate on two images at the same time, using one or both pens.
• In interactive computer mode (PC interactive), you can use the pen as a mouse to navigate, select, and scroll through content from your computer. You can split the screen and interact with two projected images at the same time. It's easy to shift between interactive computer mode and annotation mode.
Parent topic:
Related concepts
129
Using the Pens
Your projector came with a blue pen and an orange pen, identified by the color on the end of the pen.
You can use either pen, or both at the same time (one of each color).
Make sure the pen batteries are installed.
Note:
The pens turn off automatically after 20 minutes of inactivity. Slide the switch to turn the pen back on.
1 Pen tip
2 Attachment for optional strap or cord
3 Battery light
4 Power switch
5 Battery cover
1.
To turn on the pen, slide the power switch.
The green light comes on for a few seconds, then turns off. If the battery is low, the light flashes.
Note:
For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the black section near the tip of the pen.
130
2.
Do the following to use the pen as a mouse:
• To left-click, tap the board.
• To double-click, tap twice.
• To right-click, press the board with the pen for about 3 seconds.
• To click and drag, tap and drag with the pen.
• To move the cursor, hover over the board without touching it.
Note:
If you do not want to use the hovering feature, you can turn it off using the
Easy Interactive
Function
in the projector's Extended menu.
3.
When you are finished using the pen, slide the power switch to turn it off.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Related tasks
Calibrating Automatically
Calibration coordinates the positioning of the pen with the location of your cursor. You only need to calibrate the first time you use your projector, and you do not need the pens or a computer for calibration. You should not need to calibrate again unless the projector or image is moved, or the image is resized.
131
Note:
You can start Auto Calibration by pressing the
User
button on the remote control or by pressing the
Menu
button on the remote control as described here.
1.
Press the
Menu
button, select the
Extended
menu, and press
Enter
.
2.
Select the
Easy Interactive Function
setting and press
Enter
.
132
3.
Select
Auto Calibration
and press
Enter
.
4.
Adjust the focus if necessary, by opening the cover on the side of the projector and sliding the focus lever.
5.
Press
Enter
to select
Yes
.
A pattern appears then disappears, and the system is calibrated. If you see a message that calibration failed, you need to calibrate manually.
The cursor location and pen position should match after calibration. If not, you may need to calibrate manually.
Parent topic:
Related tasks
Calibrating Manually
If the cursor location and pen position do not match after auto calibration, you can calibrate manually.
133
1.
Press the
Menu
button, select the
Extended
menu, and press
Enter
.
2.
Select the
Easy Interactive Function
setting and press
Enter
.
134
3.
Select
Manual Calibration
and press
Enter
.
4.
Adjust the focus if necessary, by opening the cover on the side of the projector and sliding the focus lever.
5.
Press
Enter
to select
Yes
.
A flashing green circle appears in the upper left corner of your projected image.
6.
Touch the center of the circle with the tip of the pen.
The circle disappears, and you see another circle below the first one.
Note:
For the most accurate calibration, make sure you touch the center of the circle.
135
7.
Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next circle appears at the top of a new column.
Note:
Make sure you are not blocking the signal between the pen and the interactive receiver (next to the projection window on the projector).
If you make a mistake, press the
Esc
button on the remote control to go back to the previous circle.
To restart the calibration process, press and hold the
Esc
button for 2 seconds.
8.
Continue until all of the circles disappear.
Parent topic:
Related tasks
136
Whiteboard Mode
You can use the pens to write or draw on the projection surface just as you would on a chalkboard or dry erase board.
You can also do the following:
• Insert images from a thumbdrive or scanner and resize, rotate, or crop the images
• Insert a background pattern or template, or a variety of shapes
• Save, print, or email your whiteboard pages
Selecting Background Templates
Zooming Images in Whiteboard Mode
Inserting and Working With Images
Selecting Line Width and Color
Inserting a Document or Image From a Scanner
Saving Pages in Whiteboard Mode
Emailing Your Whiteboard Pages
Parent topic:
Using the Whiteboard Toolbars
You can use both pens at the same time in whiteboard mode.
1.
Press the
Whiteboard
button on the remote control or control pad.
You see the whiteboard screen, with the main toolbar and the bottom toolbar:
137
2.
To move the main toolbar to the other side of the screen, select the
Note:
You can use the pen to move the arrow up or down.
arrow.
3.
To add a new page, select the New page icon on the bottom toolbar.
Your current page appears as a thumbnail image on the bottom toolbar.
4.
To close the main toolbar, select the icon at the bottom of the toolbar.
Note:
If you want to hide the toolbar automatically after drawing, select the the toolbar.
icon at the bottom of
5.
To show or hide the bottom toolbar, select one of the
Parent topic:
Related references
138
arrows.
The Main Whiteboard Toolbar
The main whiteboard toolbar lets you draw, write, and insert images and backgrounds. The toolbar also lets you easily switch to annotation or computer interactive mode.
Switch to annotation mode
Switch to whiteboard mode
Undo the last annotation
Redo the last undo
139
Insert a background pattern or template
Zoom into and out of image
Crop or trim an inserted image
Select an inserted image to move, resize, or rotate
Insert a .jpg or .png image from a thumbdrive or network folder
Insert a circle, square, triangle, or other shape
Change custom pen color and width
Write or draw free-form lines with custom pen
Change highlighter pen color
Write or draw free-form lines with transparent highlighter pen
Black pen (fine point on left, thick on right)
Red pen (fine point on left, thick on right)
Blue pen (fine point on left, thick on right)
Eraser (thin width on left, thick on right)
Clear all annotations
Hide the toolbar after each annotation
140
Close the toolbar
Parent topic:
Selecting Background Templates
In whiteboard mode, you can insert horizontal lines, a graph-paper grid, or other background template.
You can select from 10 preinstalled patterns. In addition, you can add 5 custom template patterns by accessing the projector through your web browser. Once your custom template patterns are registered, you can place them on your whiteboard pages whenever you want.
1.
In whiteboard mode, select the
You see three additional icons.
2.
Select one of the following:
Template tool on the main toolbar.
• To add horizontal lines, select the the lines.
• To add a graph-paper grid, select the spacing.
Ruler icon. Select the icon again to change the spacing of
Grid icon. Select the icon again to change the grid
• To choose from a variety of template patterns, select the Select pattern icon.
If you selected the ruler lines or grid pattern, you see the pattern projected. If you selected the icon, you see additional template patterns (with either light or dark backgrounds).
3.
Select one of the template patterns. If you want to use the pattern for all the pages in the current session, select
Apply to all pages
.
Parent topic:
Related tasks
Adding Templates from a Web Browser
Zooming Images in Whiteboard Mode
You can use the pen to zoom in and pan around your enlarged image, then zoom out when you are done.
141
1.
Select the Zoom tool.
2.
Do one of the following to adjust the image if necessary:
• Select the
• Select the icon to enlarge the image.
icon to shrink the image.
• Select the icon to return to the original size.
• Select the icon to pan around the enlarged area.
Parent topic:
Inserting and Working With Images
In whiteboard mode, you can use the Insert tool to insert an image from a thumbdrive or a network folder. Images can be in .png or .jpg format, with a maximum size of 2048 × 2048 pixels. Once the image is projected, you can move, resize, rotate, or crop it.
Note:
You can also use the whiteboard mode.
tool on the bottom toolbar to import files (including pdf files) in
1.
Select the Insert tool.
2.
Select the image you want to add, then select
Insert Image
.
After a moment, the image appears on the whiteboard page.
3.
If you want to move or edit the image, tap the Select tool.
4.
Once you have selected the image, do any of the following as necessary:
• To move the image, touch inside it and drag with the pen.
• To resize the image, touch the edge and drag inward to shrink or outward to enlarge.
• To rotate the image, touch the top, then drag any of the 4 blue handles in the corners.
142
• To crop the image, select the
Parent topic:
Trim tool, then drag the corner of the image.
Using the Shapes Tool
You can add a variety of shapes to your projected image and select the color and line width.
1.
Select the Shapes tool.
The Shapes box opens:
2.
Select the line width, color, and shape you want to create, or select the own shape.
3.
Drag the pen on the projection surface to draw the shape you want.
Parent topic:
Line tool to define your
Selecting Line Width and Color
You can select the color and line width for both the custom Pen and the Highlighter tools.
1.
Select the icon next to the custom Pen or Highlighter annotation tool.
A box like the following appears:
143
2.
Select the line width and color you want to use for the Pen or Highlighter tools.
3.
Select the or tool, then use the pen to write or draw on the projection surface.
Parent topic:
The Bottom Whiteboard Toolbar
The bottom whiteboard toolbar lets you add scanned or imported images, and view, save, print, or email your pages.
Show or hide bottom toolbar
Start a new meeting or whiteboard session
Open a .jpg, .png, or .pdf file from a thumbdrive or network folder. When you open a multipage pdf, each page in the document appears on a separate whiteboard page.
Scan and insert an image
144
Open a new page. The current page appears as a thumbnail on the bottom toolbar.
Display the previous page thumbnail
Display the next page thumbnail
Print one or more pages
Save a page or a series of pages on a thumbdrive or network folder
Email a page or series of pages
Display a help screen for the toolbar functions
Parent topic:
Related tasks
Inserting a Document or Image From a Scanner
Saving Pages in Whiteboard Mode
Emailing Your Whiteboard Pages
Selecting Whiteboard Settings
Follow the instructions in these sections to select settings for capturing, scanning, saving, printing, and emailing in whiteboard mode.
Selecting Basic Whiteboard Settings and Policies
Selecting Whiteboard Print Settings
Selecting Settings for Saving Whiteboard Pages
Selecting Settings for Emailing Whiteboard Pages
Parent topic:
145
Selecting Basic Whiteboard Settings and Policies
You can select the whiteboard features you want to use and control the way whiteboard pages are saved in the projector.
1.
Press the
Menu
button on the remote control.
2.
Select the
Extended
menu and press
Enter
.
3.
Select
Whiteboard Settings
and press
Enter
.
146
4.
Select
Basic
and press
Enter
.
5.
Select the following basic options as necessary:
•
Administrator Password
lets you enter a password up to 16 alphanumeric characters long for controlling whiteboard settings. This password is also used for network settings.
•
Clock Display Settings
lets you control the date and time display on the bottom whiteboard toolbar.
•
Delete All Internal Data
lets you delete data stored in the projector. Use this option if you have problems with internal storage, or you need to dispose of the projector or have it repaired.
Note:
Use the displayed keyboard to enter the password. Press the arrow buttons on the remote control to highlight characters and press
Enter
to select them.
147
6.
Select the
Policy
menu and press
Enter
.
7.
Select the following policy options as necessary:
•
Policy Setting
options let you disable capturing, printing, scanning, USB storage, network storage, or emailing from the projector. All features are enabled by default.
•
Internal Storage
settings let you control the use of the projector's internal storage. In most cases, you should leave this setting
On
, and select
Retain
for saved data. The
Backup Time for Saved
Data
setting determines how often whiteboard pages are backed up automatically in case of a power outage.
8.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Selecting Whiteboard Print Settings
You can select the default settings for printing whiteboard pages from the projector.
1.
Press the
Menu
button on the remote control.
148
2.
Select the
Extended
menu and press
Enter
.
3.
Select
Whiteboard Settings
and press
Enter
.
4.
Select
and press
Enter
.
149
5.
Select the following printing options as necessary:
•
Default Printer
lets you select either
USB
or
Network
for the printer connection. You can change this setting when you print in whiteboard mode, but not in annotation mode.
•
Paper Size
lets you select either
Letter
or
A4
as the default paper size.
•
Network Printer Settings
let you enter the IP address for a printer connected to the same network as the projector. Once this is set, you can select
Get printer information
to have the projector communicate with the printer and automatically determine the printer type. You can also select the
Printer Type
manually.
•
Test Print
lets you send a test page to the connected printer.
Note:
Use the displayed keyboard to enter the IP address if necessary. Press the arrow buttons on the remote control to highlight numbers and press
Enter
to select them.
6.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Related tasks
Selecting Settings for Saving Whiteboard Pages
You can select the default settings for saving whiteboard pages from the projector.
1.
Press the
Menu
button on the remote control.
150
2.
Select the
Extended
menu and press
Enter
.
3.
Select
Whiteboard Settings
and press
Enter
.
4.
Select
Save
and press
Enter
.
151
5.
Select the following options for saving as necessary:
•
Default Save Location
lets you select either
USB
or
Network
for saving on a USB thumb drive or network folder. You can change this setting when you save in whiteboard mode, but not in annotation mode.
•
Network Folder Settings
let you enter a network folder name, user name, and password for saving whiteboard pages. The
UNC Address
setting (Universal Naming Convention) lets you set a folder and path in the following format: \\host name\share name\relative path. You can enter up to 116 alphanumeric characters for the address and 64 characters for the user name or password.
Note:
The folder must be on a shared network drive. To save to a folder on a different network segment, use the
WINS server
setting on the wired or wireless network menu.
•
Check Connection
lets you test the network connection.
Note:
Use the displayed keyboard to enter the address, user name, and password if necessary.
Press the arrow buttons on the remote control to highlight numbers and press
Enter
to select them.
6.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Related tasks
Saving Pages in Whiteboard Mode
Selecting Wired Network Settings
Selecting Wireless Network Settings Manually
Saving Images in Annotation Mode
Selecting Settings for Emailing Whiteboard Pages
You can select the settings for emailing whiteboard pages from the projector.
1.
Press the
Menu
button on the remote control.
152
2.
Select the
Extended
menu and press
Enter
.
3.
Select
Whiteboard Settings
and press
Enter
.
4.
Select
and press
Enter
.
153
5.
Select the following options for emailing as necessary:
•
SMTP Server
lets you enter the mail server address for sending emails from the projector. If you don't know this information, check with your IS department or ISP.
•
Port Number
lets you enter a port number for the SMTP server. The default port is 25.
•
Reply to
lets you enter an email address to use when an error occurs while sending an email. You can enter up to 64 alphanumeric characters.
•
Default e-mail address
lets you enter an optional address for testing. You can enter up to 64 alphanumeric characters.
•
Send a test e-mail
connects to the SMTP server and sends a test email to the address you set as the default.
Note:
Use the displayed keyboard to enter the addresses. Press the arrow buttons on the remote control to highlight numbers or characters and press
Enter
to select them.
6.
When you finish selecting settings, select
Setup Complete
and follow the on-screen instructions to save your settings and exit the menus.
Parent topic:
Related tasks
Emailing Your Whiteboard Pages
Inserting a Document or Image From a Scanner
You can scan a paper document into a new page in whiteboard mode. Make sure a supported Epson allin-one printer is connected to the control pad (or to your network).
Note:
Standalone scanners are not supported.
1.
Place your document on the scanner glass or in the automatic document feeder (if available).
Note:
You can place up to 10 sheets in the ADF. If you want to scan a longer document, scan the pages in batches of 10.
2.
Select the Scan tool on the bottom toolbar.
You see the Scan screen:
154
3.
Select the following settings:
• Select
Color
or
Monochrome
• Select the orientation for the scanned document.
• Under ADF, select
On
if you placed your document in the automatic document feeder.
4.
Select
Advanced
to access additional options.
5.
Select
Scan
on the Scan screen.
After a moment, you see your document or image on the screen.
Note:
Multi-page documents appear on multiple whiteboard pages.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Saving Pages in Whiteboard Mode
You can save your pages as .png or .pdf files and select the location (network folder or thumbdrive) where you want to store your files.
1.
Press the
Save
button on the control pad or remote control, or select the bottom toolbar.
Save tool on the
155
2.
Select the location where you want to save your file, then select
OK
.
You see a screen like the following:
3.
To enter a file name, select the
File Name
text box.
The on-screen keyboard appears.
4.
Use the keyboard to enter a file name, then select
OK
.
5.
Select the location where you want to save the file.
6.
Select the format for saving. If you choose
, you can encrypt the file and add a password.
7.
Select one of the following under
Range
:
•
All
to save all the pages in the current whiteboard session (available for PDF format only)
•
Current
to save only the current whiteboard page
•
Selection
if you want to save a range of pages. Tap the numbers in the boxes to select the range of pages (available for PDF format only).
8.
When you are ready, select
Save
.
Parent topic:
Related tasks
Saving Images in Annotation Mode
Selecting Settings for Saving Whiteboard Pages
156
Working With Thumbnail Pages
Thumbnail pages are displayed on the bottom toolbar in whiteboard mode. You can scroll through your pages with the pen, select a page to display at full size, and copy or delete individual pages. The 5 rectangles in the center of the bottom toolbar shown here are thumbnail pages:
1.
To display a page at full size, select its thumbnail.
2.
To scroll through the thumbnail pages, select the next page.
3.
Do any of the following as necessary: to move to the previous page or to move to
• To add a new page, select the New page icon. A blank page opens, and this page appears as the current thumbnail on the bottom toolbar.
• To duplicate the current page, select the page displayed.
icon. The duplicate page appears after the last
• To delete the current page, select the
Parent topic:
Delete icon.
Printing in Whiteboard Mode
You can print your pages directly from the projector to a supported printer (USB or networked). You can also select settings for your printed pages, including page numbers, time and date, and collation of multiple copies.
Make sure your printer meets the control command requirements for printing from the projector.
1.
Press the
button on the control pad or remote control, or select the bottom toolbar.
You see a screen like the following:
Print tool on the
157
2.
Select the number of copies and whether you want to print in color or black only (monochrome).
3.
Select one of the following under
Range
:
•
All
to print all the pages in the current whiteboard session
•
Current
to print only the current whiteboard page
•
Range
if you want to print selected pages. Tap the numbers in the boxes to select the range of pages.
4.
To make additional settings, select
Advanced
.
5.
Select any of the following settings:
•
Paper Size
, based on the size paper loaded in the printer (Letter or A4)
•
Pages per sheet
- to print multiple reduced pages on one sheet of paper
•
Page Border
- to add a border around each page
•
Page Number
- to print the page number on each page
•
Date & Time
- to print the time and date stamp on each page
•
Collate
- to collate pages when printing multiple copies
6.
When you are ready, select
.
158
Your page or pages are printed.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Related tasks
Selecting Whiteboard Print Settings
Emailing Your Whiteboard Pages
If your projector is set up on your network, you can email your pages directly from the projector.
Note:
Mail server settings must be configured before you can email from the projector. Use the
Whiteboard Settings
function on the projector's Extended menu to configure email options.
1.
Select the Email tool on the bottom toolbar.
You see a screen like the following:
2.
To enter the email address for the recipient, tap the
E-mail Address
text box.
The on-screen keyboard appears.
3.
Use the keyboard to enter the email address, then select
OK
.
4.
Use the on-screen keyboard to enter the subject that you want to appear on the
Subject
line.
159
5.
Use the on-screen keyboard to enter a file name for the attachment.
6.
Select the file format for emailing. If you choose PDF, you can encrypt the file and add a password.
7.
Select any of the following under
Range
:
•
All
to send all the pages in the current whiteboard session (available for PDF format only)
•
Current
to send only the current whiteboard page
•
Selection
if you want to send a range of pages (available for PDF format only). Tap the numbers in the boxes to select the range of pages.
8.
When you are ready, select
Send
.
Your page or pages are sent.
Parent topic:
Related tasks
Selecting Settings for Emailing Whiteboard Pages
Annotation Mode (PC Free)
Annotation mode lets you project from a computer, tablet, video device, or other source and add notes to your projected content. You can easily switch between sources and capture, save, or print the images with annotations. You can also split the screen to annotate on two images at the same time.
Zooming Images in Annotation Mode
Saving Images in Annotation Mode
Parent topic:
Using the Annotation Toolbars
You can use both pens at the same time in annotation mode.
1.
Project an image from a connected device.
2.
Turn on one of the pens and hover near or tap the projected image.
You see the main toolbar and the bottom toolbar on the projected image, for example:
160
3.
To move the main toolbar to the other side of the screen, select the
Note:
You can use the pen to move the arrow icon up or down.
4.
To switch to one of the other modes, do one of the following:
• To switch to whiteboard mode, select the Whiteboard tool.
arrow.
• To switch to computer interactive mode, select
5.
To close the main toolbar, select the
, then select .
icon at the bottom of the toolbar.
Note:
If you want to hide the toolbar automatically after drawing, select the the toolbar.
icon at the bottom of
6.
To show or hide the bottom toolbar, select the
Parent topic:
arrow.
161
Related references
The Main Annotation Toolbar
The main annotation toolbar lets you draw and write on your projected image. The toolbar also lets you easily switch to whiteboard or computer interactive mode.
Switch to annotation mode (PC free annotation)
162
Switch to whiteboard mode
Undo the last annotation
Redo the last undo
Freeze or continue video action
Zoom into and out of the projected image. You can move the zoomed area by dragging it with the pen.
Change custom pen color and width
Write or draw free-form lines with custom pen
Change highlighter pen color
Write or draw free-form lines with transparent highlighter pen
Black pen (fine point on left, thick on right)
Red pen (fine point on left, thick on right)
Blue pen (fine point on left, thick on right)
Eraser (thin width on left, thick on right)
Clear all annotations
Hide the toolbar after each annotation
163
Close the toolbar
Switch modes. Select interactive). Select then then to switch to computer interactive mode (PC to switch back to annotation mode (PC free annotation).
Parent topic:
Zooming Images in Annotation Mode
You can use the pen to zoom in on a portion of your image, the same as you can using the
E-Zoom
button on the remote control.
1.
Select the Zoom tool.
You see a crosshair on the screen indicating the center of the enlarged area.
2.
Do one of the following to adjust the image if necessary:
• Use the pen to move the enlarged area.
• Select the
• Select the
• Select the icon to close the zoom toolbar, but leave the image enlarged.
icon to further enlarge the image.
icon to shrink the image.
• Select the icon to return to the original size.
Parent topic:
The Bottom Annotation Toolbar
The bottom annotation toolbar lets you split the screen and capture, print, or save your images.
164
Show or hide bottom toolbar
Capture the projected image. Switch to whiteboard mode to paste the image onto a new page.
Print the projected image
Save the projected image in .png format
Split the screen and project two images. When the screen is split, select the tool again to return to a single image.
Parent topic:
Related tasks
Saving Images in Annotation Mode
Printing in Annotation Mode
You can print the projected image directly from the projector to a supported printer (USB or networked).
Make sure your printer meets the control command requirements for printing from the projector.
1.
Press the
button on the control pad or remote control, or select the bottom annotation toolbar.
2.
Select the number of copies you want.
3.
When you are ready, select
.
Your page is printed.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Related tasks
Selecting Whiteboard Print Settings
Print tool on the
165
Saving Images in Annotation Mode
You can save your images as .png files in the default location set in the projector's menu system.
1.
Press the
Save
button on the control pad or remote control, or select the bottom annotation toolbar.
You see a confirmation message.
2.
Select
Yes
.
Your image is named and saved automatically.
Parent topic:
Related tasks
Saving Pages in Whiteboard Mode
Selecting Settings for Saving Whiteboard Pages
Save tool on the
Splitting the Screen
You can split the screen and project from two sources at the same time. You can annotate and interact with both sources.
Note:
Whiteboard mode is not available when the screen is split, and the following combinations of sources are not supported:
• DisplayPort and HDMI
• Any combination of LAN, USB Display, and USB1
1.
Press the
Split
button on the remote control or select the toolbar.
Split tool on the bottom annotation
The current image is reduced and appears on one side of the projection surface.
2.
Press the
Menu
button on the remote control.
You see a screen like the following:
166
3.
Select
Source
and press the
Enter
button.
You see a screen like the following:
4.
Select the source you want to use for the right half of the screen. If you want to write on a blank screen, select any unused source.
5.
Select
Execute
, then press the
Enter
button.
167
6.
Do any of the following as necessary:
• To change to a different source at any time, press the
Menu
button on the remote control, select
Source
, then select the source you want.
• To annotate on the right screen, press the
Menu
button on the remote control, select
Target Pen
Mode
, then select
Screen Right
. Set the
Pen Mode
setting to
PC Free Annotation
.
• To use computer interactive mode on the right screen, press the
Menu
button on the remote control, select
Target Pen Mode
, then select
Screen Right
. Set the
Pen Mode
setting to
PC
Interactive
.
• To reverse the left and right images, press the
Menu
button on the remote control and select
Swap Screens
.
• To make one image larger, press the
Menu
button on the remote control, select
Screen Size
, then select
Larger Left
or
Larger Right
.
Note:
When you select LAN as the source for one of the screens, you cannot change the
Pen Mode
setting.
7.
To return to displaying one image, press the
Esc
button on the remote control.
Note:
The following operations cannot be performed during split screen projection:
• Menu settings
• E-Zoom
• Switching aspect mode
• Operations made by the
User
button on the remote control
• Auto Iris
Parent topic:
Computer Interactive Mode
You can connect your computer to the projector with a USB cable, then use the pen as a mouse to navigate, select, and interact with your programs.
You can use computer interactive mode in Windows without installing any special software. For Mac
OS X, you need to install the Easy Interactive Driver.
168
Note:
To use computer interactive mode wirelessly, you need to install Easy MP Network Projection software, version 2.81 (or later), or Quick Wireless version 1.31 (or later).
You can also do the following in computer interactive mode:
• Use the Tablet PC input panel in Windows 7 or Windows Vista
• Use Ink Tools for annotation in Microsoft Office applications
Switching to Computer Interactive Mode
Adjusting the Pen Operation Area
Parent topic:
Related concepts
Windows Pen Input and Ink Tools
Switching to Computer Interactive Mode
You can easily switch between annotation and computer interactive modes. Although you can use both pens in computer interactive mode, this may cause interference in some applications. To avoid interference, turn off the unused pen or move it away from the projection surface.
• To switch to computer interactive mode, select the
Mouse icon.
Pen mode icon on the toolbar, then select the
• To switch back to annotation mode, select the
Parent topic:
Related tasks
Mouse icon, then select the Pen mode icon.
Adjusting the Pen Operation Area
The pen operation area is normally adjusted automatically if you connect a different computer or adjust the computer's resolution. If you notice that the pen position is incorrect, you can adjust the pen area manually.
Note:
Manual adjustment is not available when projecting from a LAN source.
169
1.
Project your computer's desktop.
2.
Press the
Menu
button, select the
Extended
menu, and press
Enter
.
3.
Select the
Easy Interactive Function
setting and press
Enter
.
170
4.
Select
Advanced
and press
Enter
.
5.
Select
Manual Adj. Pen Area
and press
Enter
.
6.
Press
Enter
to select
Yes
.
The mouse pointer moves toward the top left corner.
7.
When the mouse pointer stops at the top left corner of the image, touch the tip of the pointer with the pen.
The mouse pointer moves toward the bottom right corner.
8.
When the mouse pointer stops at the bottom right corner of the image, touch the tip of the pointer with the pen.
Parent topic:
171
Windows Pen Input and Ink Tools
If you are using Windows 8, Windows 7, or Windows Vista, you can use the pen input and Ink tools to add handwritten input and annotations to your work.
Note:
These features are not available when you are projecting from a LAN source.
Enabling Windows Pen Input and Ink Features
Using Windows Pen Input and Ink Features
Parent topic:
Enabling Windows Pen Input and Ink Features
If you want to use the pen input and Ink features in Windows 8, Windows 7, or Windows Vista, you need to adjust the pen settings in the Extended menu.
1.
Press the
Menu
button, select the
Extended
menu, and press
Enter
.
2.
Select the
Easy Interactive Function
setting and press
Enter
.
172
3.
Select
Number of Pen Users
and press
Enter
.
4.
Select
One User
and press
Enter
.
5.
Press
Esc
on the remote control to return to the Easy Interactive Function screen.
6.
Select
Pen Operation Mode
and press
Enter
.
7.
Select
Pen
and press
Enter
.
Parent topic:
Windows Pen Input and Ink Tools
Using Windows Pen Input and Ink Features
If you are using Windows 8, Windows 7, or Windows Vista, you can add handwritten input and convert it to text.
If you have Microsoft Office 2003 or later, you can also use the Ink function to add handwritten notes to a
Word document, Excel spreadsheet, or PowerPoint presentation.
Note:
Option names for the annotation functions may vary depending on your version of Microsoft
Office.
• To open the Touch Keyboard in Windows 8, right-click or tap and hold on the Taskbar, then select
Toolbars > Touch Keyboard
. Select the keyboard icon on the screen, then select the pen icon.
173
• To open the Tablet PC input panel in Windows 7 or Windows Vista, select
> All Programs >
Accessories > Tablet PC > Tablet PC Input Panel
.
You can write in the box using the pen, then select from a variety of options to edit and convert the text.
• To add Ink annotations in Microsoft Office applications, select the
Review
menu, then select
Start
Inking
.
Note:
In Microsoft Word or Excel, select the
Insert
tab and then click on
Start Inking
.
You can select from a variety of Ink Tools:
• To annotate your PowerPoint slides in Slideshow mode, press and hold the pen against the projection surface to right-click, then select
Pointer Options > Pen
from the pop-up menu.
Note:
This also works in Windows XP.
For more information about these features, see your Windows Help.
174
Parent topic:
Windows Pen Input and Ink Tools
175
Adjusting the Menu Settings
Follow the instructions in these sections to access the projector menu system and change projector settings.
Image Quality Settings - Image Menu
Input Signal Settings - Signal Menu
Projector Feature Settings - Settings Menu
Projector Setup Settings - Extended Menu
Projector Network Settings - Network Menu
Projector Information Display - Info Menu
Projector Reset Options - Reset Menu
Using the Projector's Menus
You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen.
1.
Press the
Menu
button on the control panel or remote control.
You see the menu screen displaying the Image menu settings.
176
2.
Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right.
Note:
The available settings depend on the current input source.
3.
To change settings in the displayed menu, press
Enter
.
4.
Press the up or down arrow button to move through the settings.
5.
Change the settings using the buttons listed on the bottom of the menu screens.
6.
To return all the menu settings to their default values, select
Reset
.
7.
When you finish changing settings on a menu, press
Esc
.
8.
Press
Menu
or
Esc
to exit the menus.
Parent topic:
Image Quality Settings - Image Menu
Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source.
177
To change settings for an input source, make sure the source is connected and select that source.
Setting
Color Mode
Brightness
Contrast
Color Saturation
Tint
Sharpness
Abs. Color Temp.
color temperature)
(absolute
Options
See the list of available Color
Modes
Varying levels available
Varying levels available
Varying levels available
Varying levels available
Varying levels available
5000 to 10000 ºK (Kelvin)
Description
Adjusts the vividness of image colors for various image types and environments
Lightens or darkens the overall image
Adjusts the difference between light and dark areas of the image
Adjusts the intensity of the image colors
Adjusts the balance of green to magenta tones in the image
Adjusts the sharpness or softness of image details
Sets the color tone based on color temperature
178
Setting
Advanced
Auto Iris
Options
Various options available
On
Off
Description
Adjusts the gamma levels and intensity of individual hues in the image
Adjusts the projected luminance based on the image brightness when certain Color Modes are selected
Note:
The
Brightness
setting does not affect lamp brightness. To change the lamp brightness mode, use the
Power Consumption
setting.
Parent topic:
Related references
Projector Feature Settings - Settings Menu
Input Signal Settings - Signal Menu
Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
179
Note:
You can restore the default settings of the
Position
,
Tracking
, and
Sync
settings by pressing the
Auto
button on the remote control.
To change settings for an input source, make sure the source is connected and select that source.
Setting
Auto Setup
Resolution
Tracking
Options
On
Off
Auto
Normal
Wide
Varying levels available
Description
Automatically optimizes computer image quality (when
On)
Sets the input signal resolution if not detected automatically using the
Auto
option
Sync.
Position
Progressive
Noise Reduction
Varying levels available
Up, down, left, right
Off
Video
Film/Auto
Off
NR1
NR2
Adjusts signal to eliminate vertical stripes in computer images
Adjusts signal to eliminate fuzziness or flickering in computer images
Adjusts the image location on the screen
Sets whether to convert interlaced-to-progressive signals for certain video image types
Off
: for fast-moving video images
Video
: for most video images
Film/Auto
: for movies, computer graphics, and animation
Reduces flickering in analog images in two levels
180
Setting
HDMI Video Range
Options
Normal
Expanded
Auto
DisplayPort Video Range
DisplayPort EQ
Input Signal
1
2
Normal
Expanded
Auto
Auto
RGB
Component
Description
Sets the video range to match the setting of the device connected to the HDMI input port
Auto
: detects the video range automatically
Expanded
: normally for images from a computer; can also be selected if the image is too dark
Normal
: normally for images from a device other than a computer; can also be selected if the black areas of the image are too bright
Sets the video range to match the setting of the device connected to the DisplayPort connector
Adjusts the input signal level for the device connected to the
DisplayPort connector. Change the setting to reduce interference or other image problems.
Specifies the signal type from input sources connected to computer ports
Auto
: detects signals automatically
RGB
: corrects color for computer/RGB video inputs
Component
: corrects color for component video inputs
181
Setting
Video Signal
Aspect
Options
Auto
Various video standards
See the list of available aspect ratios
Overscan Auto
Off
4%
8%
Parent topic:
Related references
Projector Feature Settings - Settings Menu
Options on the Settings menu let you customize various projector features.
Description
Specifies the signal type from the input sources connected to the video ports
Auto
: detects signals automatically
Sets the aspect ratio (width-toheight ratio) for the selected input source
Changes the projected image ratio to make the edges visible by a selectable percentage or automatically
182
Setting
Keystone
Split Screen
Zoom
Image Shift
Control Panel Lock
Pointer Shape
Options
H/V Keystone
Quick Corner
Screen Size
Source
Swap Screens
Audio Source
Varying levels available
Varying positions available
Full Lock
Partial Lock
Off
Three shapes available
Description
Adjusts image shape to rectangular (horizontally and vertically)
H/V Keystone
: lets you manually correct horizontal and vertical sides
Quick Corner
: select to correct image shape and alignment using an on-screen display
Divides the viewing area horizontally and displays two images side-by-side (press
Esc
to cancel split screen display)
Adjusts the size of the projected image
Adjusts the position of the projected image
Controls projector button locking to secure the projector
Full Lock
: locks all buttons
Partial Lock
: locks all buttons except the power button
Off
: no buttons locked
Changes the shape of the remote control pointer feature
183
Setting
Power Consumption
Volume
Remote Receiver
User Button
Options
Normal
ECO
Varying levels available
Front
Rear
Front/Rear
Off
Power Consumption
Info
Progressive
Closed Caption
Test Pattern
Resolution
Pattern Display
Auto Calibration
Description
Selects the brightness mode of the projector lamp
Normal
: sets maximum lamp brightness
ECO
: reduces lamp brightness and fan noise, and saves power and lamp life
Adjusts the volume of projector’s speaker system or external speakers
Limits reception of remote control signals by the selected receiver;
Off
turns off all receivers
Assigns a menu option to the
User
button on the remote control for one-touch access
184
Setting
Pattern
Options
Pattern Display
Pattern Type
User Pattern
Test Pattern
Description
Selects various pattern display options
Pattern Display
: lets you display the selected pattern type on the screen to aid in presentation
Pattern Type
: selects the type of grid or line pattern to display
User Pattern
: captures a projected screen and saves it as a pattern for display
Test Pattern
: displays a test pattern to assist in focusing and zooming the image and correcting image shape
Parent topic:
Projector Setup Settings - Extended Menu
Settings on the Extended menu let you customize various projector setup features that control its operation.
185
Setting
Easy Interactive Function
Whiteboard Settings
Options
Auto Calibration
Manual Calibration
Pen Mode
Hovering
Distance of Projectors
Number of Pen Users
Pen Operation Mode
Enable Right Click
Advanced
Description
The
Auto Calibration
and
Manual Calibration
options start calibration
Pen Mode
: selects
PC Free
Annotation
or
PC Interactive
Hovering
: lets you turn off this feature
Distance of Projectors
: adjusts pen operation when using multiple projectors in the same room. If pen operations are unstable, try changing modes.
Number of Pen Users
: selects
One User
(for compatibility with
Windows Tablet PC and Ink features) or
Two Users
Pen Operation Mode
: selects
Mouse
or
Pen
mode when one pen user is selected
Enable Right Click
: lets you use a long pen press as a right click when mouse mode is selected
Advanced
: lets you assign
Right
Click
or
Left Click
to the
Pen
Tip Button
and select either
Auto Adjust Pen Area
or
Manual Adj. Pen Area
Accesses additional whiteboard Configures your whiteboard menus settings
186
Setting
Display
Closed Caption
User's Logo
Off
CC1
CC2
–
Options
Messages
Display Background
Startup Screen
A/V Mute
Pen Toolbar Tab
Pen Mode Icon
Description
Selects various display options
Messages
: controls whether messages are displayed on the screen
Display Background
: selects the screen color or logo to display when no signal is received
Startup Screen
: controls whether a special screen appears when the projector starts up
A/V Mute
: selects the screen color or logo to display when A/V
Mute is turned on
Pen Toolbar Tab
: controls whether the tab is always displayed in annotation mode
Pen Mode Icon
: controls the display and position of the pen icon in interactive computer mode
Controls use of closed captions and selects the closed caption type (closed captions are only visible for NTSC signals connected through the
S-Video
or
Video
ports)
Creates a screen that the projector displays to identify itself and enhance security
187
Setting
Projection
Audio Input Setup
Operation
Options
Front
Front/Upside Down
Rear
Rear Upside Down
Audio Input
DisplayPort Audio Input
HDMI Audio Input
Direct Power On
Sleep Mode
Sleep Mode Timer
High Altitude Mode
Description
Selects the way the projector faces the screen so the image is oriented correctly (rear settings cannot be used with the interactive pens)
Selects the audio input source for various image sources:
Audio Input
selects the audio source when the image source is
Computer
,
Video
, or
USB-B
(if not set to
Auto
);
Audio1
,
Audio2
, or
Audio3
select the specified port regardless of the input source
Selects various operation options
Direct Power On
: lets you turn on the projector without pressing the power button
Sleep Mode
: automatically places the projector in standby mode after an interval of inactivity
Sleep Mode Timer
: sets the interval for Sleep Mode
High Altitude Mode
: regulates the projector’s operating temperature at altitudes above
4921 feet (1500 m)
188
Setting
Standby Mode
USB Type B
Time/Schedule Settings
Options
Energy Saving
Networked Standby
A/V Standby
Easy Interactive Function
USB Display/Easy Interactive
Function
Wireless Mouse/USB Display
Access additional menus
Description
Selects the following when the projector is in standby mode
(turned off):
Energy Saving
: saves power by turning off Standby Mode features
Networked Standby
: lets you monitor the projector over a network
A/V Standby
: lets you output audio to an external speaker, change the volume over the network, and output computer signals on an external monitor
Selects what happens when you connect your computer to the projector's
USB-B
port
Easy Interactive Function
: lets you use the interactive pens with your computer
USB Display/Easy Interactive
Function
: lets you display your computer's image through the
USB port and use the interactive pens with your computer
Wireless Mouse/USB Display
: lets you use the wireless mouse feature and display your computer's image through the
USB port (interactivity not available)
Sets the date and time and schedules certain projector operations to take place automatically
189
Setting
Language
Options
Various languages available
Description
Selects the language for projector menu and message displays (not changed by
Reset
option)
Parent topic:
Projector Network Settings - Network Menu
Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
190
Setting
Net. Info - Wireless LAN
Net. Info - Wired LAN
Network Configuration
Options
Connection mode
Antenna level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code
Projector Name
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Accesses additional network menus
Description
Displays wireless network status and details
Displays wired network status and details
Configures your network settings
Parent topic:
Projector Information Display - Info Menu
You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu.
191
Note:
Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Information item
Lamp Hours
Source
Input Signal
Resolution
Video Signal
Refresh Rate
Sync Info
Status
Serial Number
Description
Displays the number of hours (
H
) the lamp has been used in
Normal
and
ECO
Power Consumption modes; if the information is displayed in yellow, obtain a genuine Epson replacement lamp soon
Displays the name of the port to which the current input source is connected
Displays the input signal setting of the current input source
Displays the resolution of the current input source
Displays the video signal format of the current input source
Displays the refresh rate of the current input source
Displays information that may be needed by a service technician
Displays information about projector problems that may be needed by a service technician
Displays the projector's serial number
192
Information item
Event ID
Description
Displays the Event ID number corresponding to a specific projector problem; see the list of Event ID codes
Parent topic:
Related references
Event ID Code List
If the
Event ID
option on the Info menu displays a code number, check this list of Event ID codes for the solution to the projector problem associated with the code.
Event ID code Cause and solution
0432
0435
The EasyMP Network Projection program did not start. Turn the projector off and then on again.
0434
0482
Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again.
0484
0485
0433
0481
Cannot display the transferred images. Restart the EasyMP Network Projection program.
Communication with computer was disconnected. Restart the EasyMP Network
Projection program.
The EasyMP Network Projection program quit unexpectedly. Check the network communication status, then turn the projector off and then on again.
0483
04FE
0479
04FF
0891
A projector system error has occurred. Turn the projector off and then on again.
Cannot find an access point with the same SSID. Set your computer, access point, and projector to the same SSID.
193
Event ID code Cause and solution
0892 The WPA/WPA2 authentication type does not match. Make sure the wireless network security settings are correct.
0893
0894
The WEP/TKIP/AES encryption type does not match. Make sure the wireless network security settings are correct.
Communication with unauthorized access point was disconnected. Contact your network administrator.
0898
0899
Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you are not using DHCP, turn off the
DHCP
setting in the Network menus.
A communication error has occurred. Try restarting the EasyMP Network Projection program and restarting your projector. If that does not solve the problem, contact
Epson for help.
089A
089B
089C
089D
0B01
0BFF
The EAP authentication type does not match the network. Check the wireless LAN security settings and make sure that the security certificate is installed correctly.
EAP server authentication failed. Check the wireless LAN security settings and make sure that the security certificate is installed correctly.
EAP client authentication failed. Check the wireless LAN security settings and make sure that the security certificate is installed correctly.
Key exchange failed. Check the wireless LAN security settings and make sure that the security certificate is installed correctly.
The internal storage could not be detected correctly. Perform
Delete All Internal
Data
(Basic menu under Whiteboard Settings). Turn off the projector, disconnect the power cord, then reconnect and turn the projector back on. If that does not solve the problem, contact Epson for help.
An error has occurred in the whiteboard function. Restart the projector.
Parent topic:
Projector Information Display - Info Menu
Related references
Projector Reset Options - Reset Menu
You can reset most of the projector settings to their default values using the
Reset All
option on the
Reset menu.
194
You can also reset the projector's lamp usage timer to zero when you replace the lamp using the
Reset
Lamp Hours
option.
You cannot reset the following settings using the
Reset All
option:
• Input Signal
• User's Logo
• Language
• Network menu items
• Lamp Hours
• Password
• User Button
Parent topic:
195
Maintaining and Transporting the Projector
Follow the instructions in these sections to maintain your projector and transport it from place to place.
Projector Maintenance
Your projector needs little maintenance to keep working at its best.
You may need to clean the projection window and obstacle sensor periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
The only parts you should replace are the lamp, air filter, pen batteries and tips, and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer.
Warning:
Before cleaning any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except as specifically explained in this manual. Dangerous electrical voltages in the projector can injure you severely.
Warning:
Do not try to service this product yourself, except as specifically explained in this manual.
Refer all other servicing to qualified servicers.
Cleaning the Projection Window
Air Filter and Vent Maintenance
Replacing the Remote Control Batteries
Replacing the Control Pad Batteries
Parent topic:
Maintaining and Transporting the Projector
Cleaning the Projection Window
Clean the projection window periodically, or whenever you notice dust or smudges on the surface.
196
• To remove dust or smudges, gently wipe the projection window with lens-cleaning paper.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the projection window.
Warning:
Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Caution:
Do not used canned air, or the gases may leave a residue.
Parent topic:
Cleaning the Obstacle Sensor
Clean the projector's obstacle sensor glass (circled in red) periodically, or if you see a message telling you to remove any obstacles that are interfering with the projection area.
• To remove dust or smudges, gently wipe the obstacle sensor glass with lens-cleaning paper.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the obstacle sensor glass.
Warning:
Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Caution:
Do not used canned air, or the gases may leave a residue.
197
Parent topic:
Cleaning the Projector Case
Before cleaning the projector case, turn off the projector and unplug the power cord.
• To remove dust or dirt, use a soft, dry, lint-free cloth.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector.
Caution:
Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a residue.
Parent topic:
Air Filter and Vent Maintenance
Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.
If regular maintenance is not performed, your Epson projector will notify you when the temperature inside the projector has reached a high level. Do not wait until this warning appears to maintain your projector filter as prolonged exposure to high temperatures may reduce the life of your projector or lamp.
Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties.
Cleaning the Air Filter and Vents
Parent topic:
Related references
Cleaning the Air Filter and Vents
Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them.
1.
Turn off the projector and unplug the power cord.
198
2.
Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush).
Note:
You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it.
Caution:
Do not use canned air. The gases may leave a residue or push dust and debris into the projector's optics or other sensitive areas.
3.
If dust is difficult to remove or the air filter is damaged, replace the air filter.
Parent topic:
Air Filter and Vent Maintenance
Replacing the Air Filter
You need to replace the air filter in the following situations:
• After cleaning the air filter, you see a message telling you to clean or replace it
• The air filter is torn or damaged
You can replace the air filter while the projector is mounted on the wall or ceiling.
1.
Turn off the projector and unplug the power cord.
199
2.
Slide the air filter cover switch and open the air filter cover.
200
3.
Pull the air filter out of the projector.
Note:
Air filters contain polypropylene. Dispose of used air filters according to local regulations.
201
4.
Place the new air filter in the projector as shown.
202
5.
Close the air filter cover.
Parent topic:
Air Filter and Vent Maintenance
Related references
Optional Equipment and Replacement Parts
203
Projector Lamp Maintenance
The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replace the lamp as soon as possible when the following occurs:
• The projected image gets darker or starts to deteriorate
• A message appears when you turn on the projector telling you to replace the lamp
• The projector's lamp light is flashing orange
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Projector Information Display - Info Menu
Optional Equipment and Replacement Parts
Replacing the Lamp
Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot.
Warning:
Let the lamp fully cool before replacing it to avoid injury.
You can replace the lamp while the projector is mounted on the wall or ceiling.
1.
Turn off the projector and unplug the power cord.
2.
Allow the projector lamp to cool down for at least one hour.
Warning:
If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. If the projector is mounted on the wall or ceiling, stand to the side in case the lamp is broken.
204
3.
Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover.
4.
Slide off the lamp cover.
205
5.
Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6.
Lift up the lamp handle and gently pull the lamp out of the projector.
Note:
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
206
7.
Gently insert the new lamp into the projector along the guide rail. If it does not fit easily, make sure it is facing the right way. Press the handle down.
Caution:
Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8.
Tighten the screws to secure the lamp.
207
9.
Replace the lamp cover and tighten the screw to secure it.
Note:
Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp’s usage.
Parent topic:
Related references
Optional Equipment and Replacement Parts
Related tasks
Resetting the Lamp Timer
You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
Note:
Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information.
1.
Turn on the projector.
2.
Press the
Menu
button.
208
3.
Select the
Reset
menu and press
Enter
.
4.
Select
Reset Lamp Hours
and press
Enter
.
You see a prompt asking if you want to reset the lamp hours.
5.
Select
Yes
and press
Enter
.
6.
Press
Menu
or
Esc
to exit the menus.
Parent topic:
Related tasks
Replacing the Remote Control Batteries
The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out.
Caution:
Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
209
1.
Open the battery cover as shown.
2.
Remove the old batteries.
Warning:
If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury.
3.
Insert the batteries with the
+
and
–
ends facing as shown.
210
4.
Close the battery cover and press it down until it clicks into place.
Warning:
Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic:
Related references
Replacing the Pen Batteries
Each pen uses one AA alkaline or Sanyo Eneloop rechargeable battery. Replace the battery as soon as it runs out.
When the battery is low, the pen light flashes as you turn on the switch. When the battery runs out, the pen light goes out.
Caution:
Use only the type of batteries specified in this manual.
1.
Open the battery cover as shown.
211
2.
Remove the old battery.
Warning:
If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury.
3.
Insert the battery with the
+
and
–
ends facing as shown.
4.
Replace the battery cover and press it down until it clicks into place.
Warning:
Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic:
Replacing the Pen Tips
If the pen tips become damaged or no longer work correctly, you can replace them.
212
1.
Twist off the tip of the pen to remove it.
2.
Twist on the new tip.
Parent topic:
Related references
Optional Equipment and Replacement Parts
Replacing the Control Pad Batteries
If the control pad stops working after it has been used for a period of time, you may need to replace the batteries. The control pad uses two AA alkaline batteries.
Caution:
Use only the type of batteries specified in this manual.
Note:
If you have the optional remote control cable set (ELPKC28), you can use it instead of batteries to power the control pad.
213
1.
Remove the top cover of the control pad by prying it off as shown.
2.
Remove the old batteries.
Warning:
If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury.
3.
Insert the batteries with the
+
and
–
ends facing as shown.
214
4.
Replace the cover and press it down until it clicks into place.
Warning:
Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic:
Related references
Optional Equipment and Replacement Parts
Transporting the Projector
The projector contains precision parts, some of which are glass. Follow these guidelines to transport or ship the projector safely:
• Remove any equipment connected to the projector.
• When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile."
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box "Fragile."
Note:
Epson shall not be liable for any damages incurred during transportation.
Parent topic:
Maintaining and Transporting the Projector
215
Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Using the Projector Help Displays
Solving Image or Sound Problems
Solving Projector or Remote Control Operation Problems
Projection Problem Tips
If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
If this does not solve the problem, check the following:
• The lights on the projector may indicate what the problem is.
• The projector's Help system can display information about common problems, if the projector is operating.
• The solutions in this manual can help you solve many problems.
If none of these solutions help, you can contact Epson for technical support.
Parent topic:
Related references
Related tasks
Using the Projector Help Displays
Projector Light Status
The lights on the projector's control panel indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table below.
216
1 Power light
2 Lamp light
3 Temperature light
Power light Lamp light
Green Off
Flashing green Off
Orange Off
Flashing orange Off
Flashing red Off
Temperature light
Off
Off
Status and solution
Normal operation.
Warming up. Wait for an image to appear.
Off
Off
Standby or sleep mode.
Preparing network monitoring or shutting down.
(Wait for the light to remain orange before unplugging the projector.)
Flashing orange Projector is too hot.
• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental temperature is not too hot.
217
Power light
Red
Red
Varies
Flashing red
Red
Lamp light
Off
Temperature light
Red
Flashing red
Flashing orange
Off
Off
Flashing red Flashing red
Off Flashing red
Status and solution
Projector has overheated and turned off. Leave it turned off to cool down for five minutes.
• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
• Clean or replace the air filter.
• If operating the projector at high altitude, turn on
High Altitude Mode
.
• If the problem persists, unplug the projector and contact Epson for help.
Lamp has a problem.
• Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary.
• Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
• Clean or replace the air filter.
• If operating the projector at high altitude, turn on
High Altitude Mode
.
• If the problem persists, unplug the projector and contact Epson for help.
Replace the lamp soon to avoid damage. Do not continue using the projector.
Auto iris error. Turn the projector off, unplug it, and contact Epson for help.
A fan or sensor has a problem. Turn the projector off, unplug it, and contact Epson for help.
218
Power light
Varies
Red
Lamp light
Flashing orange
Temperature light
Status and solution
Flashing orange An obstacle has been detected around the projection window. Remove the obstacle, or clean the obstacle sensors. If the problem persists, unplug the projector and contact Epson for help.
Flashing red Flashing red Internal projector error. Turn the projector off, unplug it, and contact Epson for help.
Note:
If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help.
Parent topic:
Related references
Projector Feature Settings - Settings Menu
Projector Setup Settings - Extended Menu
Related tasks
Cleaning the Air Filter and Vents
Using the Projector Help Displays
You can display information to help you solve common problems using the projector's Help system.
1.
Turn on the projector.
2.
Press the
Help
button on the projector or the remote control.
You see the Help menu.
3.
Use the up and down arrow buttons to highlight the problem you want to solve.
Note:
You can also display image adjustment recommendations by pressing the left arrow button.
4.
Press
Enter
to view the solutions.
219
5.
When you are finished, do one of the following:
• To select another problem to solve, press
Esc
.
• To exit the help system, press
Help
.
Parent topic:
Solving Image or Sound Problems
Check the solutions in these sections if you have any problems with projected images or sound.
Solutions When No Image Appears
Solutions When Image is Incorrect Using the USB Display Function
Solutions When "No Signal" Message Appears
Solutions When "Not Supported" Message Appears
Solutions When Only a Partial Image Appears
Solutions When the Image is Not Rectangular
Solutions When the Image Contains Noise or Static
Solutions When the Image is Fuzzy or Blurry
Solutions When the Image Brightness or Colors are Incorrect
Parent topic:
Solutions When No Image Appears
If no image appears, try the following solutions:
• Press the
A/V Mute
button on the remote control to see if the image was temporarily turned off.
• Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
• Press the projector's power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver.
• Check the settings on the Signal menu to make sure they are correct for the current video source.
• Adjust the
Brightness
setting or select the
Normal
Power Consumption setting.
• Check the
Display
setting to make sure
Messages
is set to
On
.
• If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons.
220
• If the projector does not respond when you press buttons on the remote control, make sure the remote receivers are turned on.
• For images projected with Windows Media Center, reduce the screen size from full screen mode.
• For images projected from applications using Windows DirectX, turn off DirectX functions.
Parent topic:
Solving Image or Sound Problems
Related references
Projector Feature Settings - Settings Menu
Projector Setup Settings - Extended Menu
Input Signal Settings - Signal Menu
Image Quality Settings - Image Menu
Related tasks
Unlocking the Projector's Buttons
Solutions When Image is Incorrect Using the USB Display Function
If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions:
• Press the
Source Search
button on the remote control or control pad and select
USB Display
.
• Make sure the USB Display software has installed correctly. Install it manually if necessary.
• Make sure the
USB Type B
setting in the Extended menu is set to one of the
USB Display
options.
• With Mac OS X, select the
USB Display
icon in the Dock or from the
Applications
folder.
• Change the computer's resolution to 1280 × 800.
• For images projected with Windows Media Center, reduce the screen size from full screen mode.
• For images projected from applications using Windows DirectX, turn off DirectX functions.
• If the mouse cursor flickers, select
Make the movement of the mouse pointer smooth
in the Epson
USB Display Settings program on your computer (feature not available with Windows 2000).
• Turn off the
Transfer layered window
setting in the Epson USB Display Settings program on your computer.
Parent topic:
Solving Image or Sound Problems
Related references
Projector Setup Settings - Extended Menu
221
Solutions When "No Signal" Message Appears
If the "No Signal" message appears, try the following solutions:
• Press the
Source Search
button and wait a few seconds for an image to appear.
• Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary.
• Check the connection from the projector to your video sources.
• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.
• If necessary, turn the projector and the connected computer or video source off and then on again.
Parent topic:
Solving Image or Sound Problems
Displaying From a PC Laptop
If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor.
1.
Hold down the laptop's
Fn
key and press the key labelled with a monitor icon or
CRT/LCD
. (See your laptop manual for details.) Wait a few seconds for an image to appear.
2.
To display on both the laptop's monitor and the projector, try pressing the same keys again.
3.
If the same image is not displayed by the laptop and projector, check the Windows
Display
utility to make sure the external monitor port is enabled and extended desktop mode is disabled. (See your computer or Windows manual for instructions.)
4.
If necessary, check your video card settings and set the multiple display option to
Clone
or
Mirror
.
Parent topic:
Solutions When "No Signal" Message Appears
Related tasks
Using the Projector Help Displays
Displaying From a Mac Laptop
If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop for mirrored display. (See your laptop manual for details.)
1.
Open the
System Preferences
utility and select
Displays
.
2.
Select the
Display
or
Color LCD
option, if necessary.
3.
Click the
Arrange
or
Arrangement
tab.
222
4.
Select the
Mirror Displays
checkbox.
Parent topic:
Solutions When "No Signal" Message Appears
Solutions When "Not Supported" Message Appears
If the "Not Supported" message appears, try the following solutions:
• Make sure the correct input signal is selected on the Signal menu.
• Make sure the computer's display resolution does not exceed the projector's resolution and frequency limit. If necessary, select a different display resolution for your computer. (See your computer manual for details.)
Parent topic:
Solving Image or Sound Problems
Related references
Input Signal Settings - Signal Menu
Supported Video Display Formats
Solutions When Only a Partial Image Appears
If only a partial computer image appears, try the following solutions:
• Press the
Auto
button on the remote control to optimize the image signal.
• Try adjusting the image position using the
Position
menu setting.
• Press the
Aspect
button on the remote control to select a different image aspect ratio.
• If you zoomed into or out of the image using the
E-Zoom
buttons, press the
Esc
button twice to return to a full display.
• Check your computer display settings to disable dual display and set the resolution within the projector's limits. (See your computer manual for details.)
• Check the resolution assigned to your presentation files to see if they are created for a different resolution than you are projecting in. (See your software help for details.)
Parent topic:
Solving Image or Sound Problems
Related references
Input Signal Settings - Signal Menu
Supported Video Display Formats
223
Solutions When the Image is Not Rectangular
If the projected image is not evenly rectangular, try the following solutions:
• If the projector is not mounted on the wall or ceiling, place it directly in front of the center of the screen, facing it squarely, if possible.
• Use the
Image Shift
setting to adjust the image position, rather than moving the projector.
• If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape.
• Adjust the
Quick Corner
or
Keystone
setting to correct the image shape.
Parent topic:
Solving Image or Sound Problems
Related references
Projector Feature Settings - Settings Menu
Related tasks
Correcting Image Shape with the Keystone Buttons
Correcting Image Shape with Quick Corner
Solutions When the Image Contains Noise or Static
If the projected image seems to contain electronic interference (noise) or static, try the following solutions:
• Check the cables connecting your computer or video source to the projector. They should be:
• Separated from the power cord to prevent interference
• Securely connected at both ends
• Not connected to an extension cable
• Check the settings on the projector's Signal menu to make sure they match the video source. If available for your video source, adjust the
Progressive
and
Noise Reduction
settings.
• Select a computer video resolution that is compatible with the projector.
• If you are projecting from a computer, press the
Auto
button on the remote control to automatically adjust the
Tracking
and
Sync
settings.
• If you adjusted the image shape using the projector controls, try decreasing the
Sharpness
setting to improve image quality.
224
• If you are using the USB Display function, turn off the
Transfer layered window
setting in the Epson
USB Display Settings program on your computer.
Parent topic:
Solving Image or Sound Problems
Related references
Input Signal Settings - Signal Menu
Supported Video Display Formats
Related tasks
Solutions When the Image is Fuzzy or Blurry
If the projected image is fuzzy or blurry, try the following solutions:
• Adjust the image focus.
• Position the projector close enough to the screen, and directly in front of it.
• Position the projector so the keystone adjustment angle is not so wide that it distorts the image.
• Adjust the
Sharpness
setting to improve image quality.
• If you are projecting from a computer, press the
Auto
button on the remote control to automatically adjust the tracking and sync. If any bands or overall blurriness remain, display a uniformly patterned image on the screen and manually adjust the
Tracking
and
Sync
settings.
• If you are projecting from a computer, use a lower resolution.
Parent topic:
Solving Image or Sound Problems
Related references
Input Signal Settings - Signal Menu
Image Quality Settings - Image Menu
Related tasks
Cleaning the Projection Window
225
Solutions When the Image Brightness or Colors are Incorrect
If the projected image is too dark or light, or the colors are incorrect, try the following solutions:
• Press the
Color Mode
button on the remote control to try different color modes for the image and environment.
• Adjust the available settings on the Image menu for the current input source, such as
Brightness
,
Contrast
,
Tint
,
Color Adjustment
, and/or
Color Saturation
.
• Make sure you selected the correct
Input Signal
or
Video Signal
setting on the Signal menu, if available for your image source.
• Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.
• If you are using the
ECO
Power Consumption setting, try selecting
Normal
in the Settings menu.
• If the image has been progressively darkening, you may need to replace the projector lamp soon.
Parent topic:
Solving Image or Sound Problems
Related concepts
Related references
Input Signal Settings - Signal Menu
Image Quality Settings - Image Menu
Projector Feature Settings - Settings Menu
Solutions to Sound Problems
If there is no sound when you expect it or the volume is too low or high, try the following solutions:
• Adjust the projector's volume settings.
• Press the
A/V Mute
button on the remote control to resume video and audio if they were temporarily stopped.
• Press the
Source Search
button to switch to the correct input source, if necessary.
• Check your computer or video source to make sure the volume is turned up and the audio output is set for the correct source.
• Check the audio cable connections between the projector and your video source.
• Make sure any connected audio cables are labeled "No Resistance".
226
• If you are using the USB Display function, turn on the
Output audio from the projector
setting in the
Epson USB Display Settings program on your computer.
• If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac supports audio through the HDMI port. If not, you need to connect an audio cable.
• If you do not hear sound from an HDMI source, set the source to PCM output.
• Make sure the
Audio Input Setup
option is set correctly in the Extended menu.
• If you want to use a connected audio source when the projector is off, set the
Standby Mode
option to
A/V Standby
.
• If you turn the projector on immediately after turning it off, the cooling fans may run at high speed momentarily and cause an unexpected noise. This is normal.
Parent topic:
Solving Image or Sound Problems
Related references
Projector Setup Settings - Extended Menu
Solving Projector or Remote Control Operation Problems
Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Projector Power or Shut-Off Problems
Solutions to Problems with the Remote Control
Solutions to Password Problems
Solutions When the Source Cannot Be Changed
Parent topic:
Solutions to Projector Power or Shut-Off Problems
If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions:
• Make sure the power cord is securely connected to the projector and to a working electrical outlet.
• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector.
• The power cord may be defective. Disconnect the cord and contact Epson.
• If the projector's lamp shuts off unexpectedly, it may have entered standby mode after a period of inactivity. Press the power button to wake the projector.
227
• If the projector's lamp shuts off and the power and
Temp
lights are red, the projector has overheated and shut off. Check the solutions for this light status.
• If the power button on the remote control does not turn on the projector, check its batteries and make sure the
Remote Receiver
setting is turned on in the projector's menu, if available.
Parent topic:
Solving Projector or Remote Control Operation Problems
Related references
Projector Feature Settings - Settings Menu
Related tasks
Unlocking the Projector's Buttons
Solutions to Problems with the Remote Control
If the projector does not respond to remote control commands, try the following solutions:
• Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries.
• Make sure you are operating the remote control within the reception angle and range of the projector.
• Make sure the projector is not warming up or shutting down.
• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release the button to wake the remote control up.
• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the projector's remote receivers. Dim the lights or move the projector away from the sun or interfering equipment.
• If available, turn off one of the remote receivers in the projector's menu system, or check if all the remote receivers were turned off.
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to check or change the ID setting (feature not available with all projectors).
• If you lose the remote control, you can order another one from Epson.
Parent topic:
Solving Projector or Remote Control Operation Problems
Related references
Projector Feature Settings - Settings Menu
Optional Equipment and Replacement Parts
228
Solutions to Password Problems
If you cannot enter or remember a password, try the following solutions:
• You may have turned on password protection without first setting a password. Try entering
0000
using the remote control.
• If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson. Provide the request code and proof of ownership for assistance in unlocking the projector.
• If you lose the remote control you cannot enter a password. Order a new one from Epson.
Parent topic:
Solving Projector or Remote Control Operation Problems
Solutions When the Source Cannot Be Changed
If you are having trouble changing the source, make sure the projector is not opening an image, scanning, saving, or printing at the same time. These processes may take time to complete, and the source cannot be changed during processing.
Parent topic:
Solving Projector or Remote Control Operation Problems
Solving Interactive Problems
Check the solutions in these sections if you have problems using the interactive system.
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears
Solutions When the Interactive Pens Do Not Work
Solutions When the Interactive Pen Position Is Not Accurate
Solutions When Manual Calibration is Difficult
Solutions When the Interactive Pens Are Slow or Difficult to Use
Solutions When the Interactive Pens Cause Interference or Unwanted Effects
Solutions for Problems With Capturing, Printing, Saving, or Scanning
Solutions When Inking Does Not Appear in Microsoft Office
Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear
Solutions When the Time Is Incorrect in Whiteboard Settings
Parent topic:
Solutions When "Error Occurred in the Easy Interactive Function" Message Appears
If the "Error occurred in the Easy Interactive Function" message appears, contact Epson for help.
229
Parent topic:
Related references
Solutions When the Interactive Pens Do Not Work
If the pens do not work, try the following solutions:
• The pens turn off automatically if you forget to turn them off. Slide the switch to turn the pen back on.
• Make sure you are not covering the black section near the tip of the pen.
• Make sure nothing is blocking the signal between the pen and the interactive pen receiver on the projector.
• Try holding the pen at a different angle so that your hand is not blocking the signal.
• Make sure the cable cover is in place to keep cables from blocking the signal.
• Make sure the pen battery has enough power. Try replacing the battery.
• If you are projecting from a computer, make sure the USB cable is connected to the computer and projector.
• Dim the room lights and turn off any fluorescent lights. Make sure the projection surface and pen receiver are not in direct sunlight or other sources of bright lighting.
• Do not place any type of decorative lights around the projector or projection surface.
• If the pen tip is worn out or damaged, you may need to replace it.
• Make sure the pen receiver on the projector is clean and free from dust.
• Make sure there is no interference from infrared remote controls, mice, or infrared microphones.
• Make sure the
USB Type B
option on the Extended menu is set to
Easy Interactive Function
or
USB
Display/Easy Interactive Function
.
• Make sure you have calibrated the system. Try recalibrating.
• If you are projecting from a laptop computer, make sure the battery has enough power, or connect the laptop to a power outlet.
• Make sure
Pen Mode
and
Pen Operation Mode
are set correctly in
Easy Interactive Function
on the Extended menu.
• If you are using multiple projectors in the same room, change the
Distance of Projectors
setting in
Easy Interactive Function
on the Extended menu.
Parent topic:
230
Related references
Projector Setup Settings - Extended Menu
Related tasks
Solutions When the Interactive Pen Position Is Not Accurate
If the pen position is not the same as the cursor, try the following solutions:
• Make sure you have calibrated the system. Try manual calibration.
• Make sure the cable cover is in place to keep cables from blocking the signal.
• Try adjusting the pen operation area.
• If you use the
E-Zoom +
button on the remote control to enlarge the image, the pen position is not accurate. When you return the image to the original size, the position should be correct.
• Try changing the computer's resolution to 1280 × 800.
Parent topic:
Related tasks
Adjusting the Pen Operation Area
Solutions When Manual Calibration is Difficult
If you are having trouble calibrating manually, try the following solutions:
• If the circle does not move to the next position, or it moves automatically, dim or turn off any bright lights near the projection surface.
• Make sure the projector is not too close to the projection surface.
Parent topic:
231
Solutions When the Interactive Pens Are Slow or Difficult to Use
If the pens are difficult to use or respond too slowly, try the following solutions:
• For easier operation, hold the pen perpendicular to the projection surface.
• For the best performance, connect your computer to the projector using a VGA, HDMI, or DisplayPort cable for display and the USB cable for interactivity.
• If you are using a computer, try setting your computer's display to 1280 × 800.
• If you are using USB display in Windows, you may need to disable Windows Aero in the Epson USB
Display Settings program on your computer.
• If you are projecting over a network, refer to the
EasyMP Network Projection Operation Guide
for performance adjustment instructions.
Parent topic:
Related concepts
Related tasks
Solutions When the Interactive Pens Cause Interference or Unwanted Effects
If the pens are causing interference or unwanted effects, try the following solutions:
• When both pens are used at the same time, make sure they are approximately 4 inches (10.16 cm) apart.
• Turn off the pens when they are not in use.
• Do not rest the pens on the image area of an interactive table, to avoid interference with your computer's mouse.
• Try changing the
Number of Pen Users
setting from
One User
to
Two Users
.
• Turn off hovering.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
232
Solutions for Problems With Capturing, Printing, Saving, or Scanning
If you are having trouble capturing and pasting, or printing, saving, or scanning, try the following solutions:
• If you start a process using one of the pens, you must complete it using the pen. If you start using the remote control or control pad, you must complete the process using the remote control or control pad.
• If you are having trouble pasting a captured image, make sure the image is not protected.
• If a black frame appears around a pasted image, it may be because the image was shifted or resized.
• If you are having trouble printing or scanning, make sure the printer is not out of ink, jammed, or in any other error state.
• For USB printing or scanning, make sure a USB cable is connected between the projector's
USB-A
port and the
USB-B
port on the control pad. Make sure another USB cable is connected between the
Printer
port on the control pad and the printer itself.
• For USB printing or scanning, try connecting a different USB cable, and make sure the cables are less than 16 ft (4.9 m) long.
• Connect only one printer or multifunction device at a time, and make sure the device is supported by the projector.
• Check the
Whiteboard Settings
on the Extended menu.
Parent topic:
Related references
Printer and All-in-One Control Command Requirements
Related tasks
Connecting a Computer to the Control Pad
Connecting a Printer to the Control Pad
Related topics
Solutions When Inking Does Not Appear in Microsoft Office
If
Start Inking
does not appear on the Review tab in your Microsoft Office application, try this solution.
Open the projector's Extended menu and change the following settings in
Easy Interactive Function
:
• Set the
Number of Pen Users
to
One User
.
• Set the
Pen Operation Mode
to
Pen
.
233
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Related tasks
Enabling Windows Pen Input and Ink Features
Using Windows Pen Input and Ink Features
Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear
If you are having trouble using the pen with a network connection, or the toolbars do not appear on your projected image, try the following solutions:
• If you are using EasyMP Network Projection software, select
Options
, then make sure
Use
Interactive Pen
is enabled. Also, select the
Adjust performance
tab and select
Transfer layered window
.
• If you are using the Quick Wireless Connection USB Key, start the Epson Quick Wireless Connections
Settings program on your computer, select the
General settings
tab, then make sure
Use Interactive
Pen
is enabled. Also, select the
Adjust performance
tab and select
Transfer layered window
.
Parent topic:
Related concepts
Solutions When the Time Is Incorrect in Whiteboard Settings
If the time is incorrect on internal storage settings for whiteboard mode, you may need to update the
Time/Schedule Settings
on the Extended menu.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Solving Network Problems
Check the solutions in these sections if you have problems using the projector on a wired or wireless network.
Solutions When Wireless Authentication Fails
Solutions When You Cannot Access the Projector Through the Web
Solutions When Network Alert E-Mails are Not Received
234
Parent topic:
Solutions When Wireless Authentication Fails
If the wireless settings are correct, but authentication fails, you may need to update the
Time/Schedule
Settings
on the Extended menu.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Solutions When You Cannot Access the Projector Through the Web
If you are unable to access the projector through a web browser, make sure you are using the correct ID and password, which are case sensitive.
• For the user ID, enter
EPSONWEB
. (You cannot change the user ID.)
• For the password, enter the password set in the projector's Network menu. The default password is
admin
.
• Make sure you have access to the network the projector is on.
Parent topic:
Solutions When Network Alert E-Mails are Not Received
If you do not receive an e-mail alerting you to problems with a projector over the network, try the following solutions:
• Make sure the projector is turned on and connected to the network correctly. (If an error shut down the projector, it cannot send an e-mail.)
• Make sure you set up the projector e-mail alert settings correctly on the projector's network Mail menu or in the network software.
• Set the
Standby Mode
setting to
Network Standby
so the network software can monitor the projector in standby mode.
Parent topic:
Related references
Projector Setup Settings - Extended Menu
Related tasks
Setting Up Projector Network E-Mail Alerts
235
Where to Get Help
If you need to contact Epson for technical support services, use the following support options.
Internet Support
Visit Epson's support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems with your projector. You can download utilities and documentation, get
FAQs and troubleshooting advice, or e-mail Epson with your questions.
Speak to a Support Representative
To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562)
276-4394 (U.S.) or (905) 709-3839 (Canada).
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time,
Saturday.
Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Before you call, have the following information ready:
• Product name
• Product serial number (located on the bottom or rear of the projector, or in the menu system)
• Proof of purchase (such as a store receipt) and date of purchase
• Computer or video configuration
• Description of the problem
Purchase Supplies and Accessories
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com
(U.S. sales) or www.epson.ca
(Canadian sales).
To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).
Parent topic:
236
Technical Specifications
These sections list the technical specifications of your projector.
General Projector Specifications
Projector Dimension Specifications
Projector Electrical Specifications
Projector Environmental Specifications
Projector Safety and Approvals Specifications
Supported Video Display Formats
USB Display System Requirements
Printer and All-in-One Control Command Requirements
General Projector Specifications
Type of display
Resolution
Lens
Color reproduction
Brightness
Contrast ratio
Image size
Projection distance
Poly-silicon TFT active matrix
1280 × 768 pixels (WXGA)
F= 1.80
Focal length: 3.71 mm
Full color, 16.77 million colors
Normal Power Consumption mode:
White light output 3100 lumens (ISO 21118 standard)
Color light output 3100 lumens
ECO Power Consumption mode:
White light output 1800 lumens (ISO 21118 standard)
3000 to 1 with Auto Iris on and Normal Power Consumption mode
60 to 100 inches (1.52 to 2.54 m)
13.7 to 23.5 inches (0.35 to 0.60 m)
237
Projection methods
Optical aspect ratio
(width-to-height)
Focus adjustment
Zoom adjustment
Zoom ratio
(Tele-to-Wide)
Internal sound system
Noise level
Front, wall, or ceiling-mounted
16:10
Manual
Digital
1:1.35
Keystone correction angle
USB-B port compatibility
USB-A port compatibility
10 W monaural
35 dB (Normal Power Consumption mode)
28 dB (ECO Power Consumption mode)
Vertical: ± 3º (manual);
Horizontal: ± 3º (manual);
Meets USB 2.0 specification
2 ports that meet USB 2.0 specification
Parent topic:
Projector Lamp Specifications
Type
Power consumption
Lamp life
UHE (Ultra High Efficiency)
215 W
Normal Power Consumption mode:
Up to about 3500 hours
ECO Power Consumption mode:
Up to about 5000 hours
Note:
Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Parent topic:
238
Remote Control Specifications
Reception range
Batteries
19.7 feet (6 m)
Two alkaline or manganese AA
Parent topic:
Projector Dimension Specifications
Height
(excluding feet)
Width
Depth
Weight
6.1 inches (155 mm)
14.4 inches (367 mm)
14.8 inches (375 mm)
12.3 lb (5.6 kg)
Parent topic:
Control Pad Specifications
Height
Maximum Height
(excluding rubber feet)
Width
Depth
Maximum Depth
Weight
(excluding batteries)
5.9 inches (149 mm)
6.0 inches (153.5 mm)
5.4 inches (136 mm)
1.1 inches (29 mm)
1.2 inches (29.9 mm)
0.53 lb (240 g)
Parent topic:
239
Projector Electrical Specifications
Rated frequency
Power supply
Power consumption
(110 to 120 V)
Power consumption
(220 to 240 V)
50/60 Hz
100 to 240 VAC
3.2 to 1.5 A
Operating:
Normal Power Consumption mode: 322 W
ECO Power Consumption mode: 231 W
Standby:
0.20 W (Communication Off), 4.6 W (Communication On)
Operating:
Normal Power Consumption mode: 307 W
ECO Power Consumption mode: 222 W
Standby:
0.27 W (Communication Off), 5.0 W (Communication On)
Parent topic:
Projector Environmental Specifications
Temperature
Humidity
(relative, non-condensing)
Operating altitude
Operating: 41 to 95 ºF (5 to 35 ºC)
Storage: 14 to 140 ºF (–10 to 60 ºC)
Operating: 20 to 80%
Storage: 10 to 90%
Up to 4921 feet (1500 m)
Up to 7500 feet (2286 m) with High Altitude Mode enabled
Parent topic:
240
Projector Safety and Approvals Specifications
United States
Canada
FCC Part 15 Class B (DoC)
UL60950-1
ICES-003 Class B
CSA C22.2 No. 60950-1
Parent topic:
Supported Video Display Formats
For best results, your computer monitor or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
Your computer's monitor or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.)
The table here lists the compatible refresh rate and resolution for each compatible video display format.
Display format
Computer signals (analog RGB)
Refresh rate (in Hz)
VGA
SVGA
60/72/75/85
56/60/72/75/85
XGA
WXGA
60/70/75/85
60
60
60/75/85
WXGA+
WXGA++
SXGA
60/75/85
60
70/75/85
60/75/85
60/75/85
Resolution (in pixels)
640 × 480
800 × 600
1024 × 768
1280 × 768
1366 × 768
1280 × 800
1440 × 900
1600 × 900
1152 × 864
1280 × 1024
1280 × 960
241
Display format
SXGA+
WSXGA+*
UXGA
Refresh rate (in Hz)
60/75
60
60
MAC13"
MAC16"
MAC19"
67
75
75
59
75 MAC21"
Composite video
TV (NTSC)
TV (SECAM)
60
50
50/60 TV (PAL)
Component video
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
60
50
60
50
50/60
50/60
HDMI and DisplayPort input signals
VGA 60
SVGA
XGA
WXGA
60
60
60
60
60
242
720 × 480
720 × 576
720 × 480
720 × 576
1280 × 720
1920 × 1080
640 × 480
800 × 600
1024 × 768
1280 × 800
1280 × 768**
1366 × 768
Resolution (in pixels)
1400 × 1050
1680 × 1050
1600 × 1200
640 × 480
832 × 624
1024 × 768
1024 × 768
1152 × 870
720 × 480
720 × 576
720 × 576
Display format
WXGA+
WXGA++
WSXGA+
SXGA
SXGA+
UXGA
SDTV (480i***/480p)
SDTV (576i***/576p)
HDTV (720p)
HDTV (1080i)***
HDTV (1080p)
60
60
60
60
Refresh rate (in Hz)
60
60
60
60
50
50/60
50/60
24***/30***/50/60
Resolution (in pixels)
1440 × 900
1600 × 900
1680 × 1050
1280 × 960
1280 × 1024
1400 × 1050
1600 × 1200
720 × 480
720 × 576
1280 × 720
1920 × 1080
1920 × 1080
* Only compatible when
Wide
is selected as the Resolution.
** DisplayPort input only.
*** HDMI input only.
Parent topic:
USB Display System Requirements
Your computer system must meet the system requirements here to use the projector's USB Display software.
243
Requirement
Operating system
USB version
CPU
Memory
Hard disk space
Display
Windows
Windows 2000 (Service Pack 4 only)
Windows XP Professional, Home
Edition, and Tablet PC Edition (32-bit); except for Service Pack 1
Windows Vista Ultimate, Enterprise,
Business, Home Premium, and Home
Basic (32-bit)
Mac
Mac OS X 10.5.8, 10.6.x, 10.7.x, or
10.8.x
Windows 7 Ultimate, Enterprise,
Professional, and Home Premium (32and 64-bit); Home Basic and Starter (32bit)
Windows 8, Windows 8 Enterprise and
Pro (32- and 64-bit)
USB 1.1 and above (USB 2.0 recommended)
Mobile Pentium III 1.2 GHz or faster
(1.6 GHz or faster recommended)
Power PC G4 1 GHz or faster (Core
Duo 1.83 GHz or faster recommended)
512MB or more 256MB or more (512MB or more recommended)
20MB or more
Resolution between 640 × 480 and
1600 × 1200, 16-bit color or greater
Resolution between 640 × 480 and
1680 × 1200, 16-bit color or greater
Parent topic:
Printer and All-in-One Control Command Requirements
To print or scan directly from the projector, your printer or all-in-one device must support the following control commands:
• ESC/P-R (USB or networked)
• ESC/Page, ESC/Page-Color (networked only)
• PCL6 (networked only)
Parent topic:
244
Notices
Check these sections for important notices about your projector.
Wireless Telegraphy Act Regulations
Recycling
Epson offers a recycling program for end of life products. Please go to www.epson.com/recycle for information on how to return your products for proper disposal.
Parent topic:
Important Safety Information
Caution:
Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
Except as specifically explained in this
User's Guide
, do not attempt to service this product yourself.
Refer all servicing to qualified service personnel.
Warning:
The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.
Caution:
When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Parent topic:
245
Important Safety Instructions
Follow these safety instructions when setting up and using the projector:
• Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.
• Do not place your hand or any object near the projection window. The high temperature of this area could cause burns, fire, or other damage.
• Do not place the projector on an unstable cart, stand, or table.
• Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than
1.5° forward or back.
• If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using mounting hardware designed for use with this projector.
• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants. This may cause the projector case to crack and the projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and could damage the projector.
• Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of magnetic fields.
• Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not insert the plug into a dusty outlet. Insert the plug firmly into the outlet. Do not pull the power cord when disconnecting the plug; always be sure to hold the plug when disconnecting it. Do not overload wall outlets, extension cords, or power strips. Failure to comply with these precautions could result in fire or electric shock.
• Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.
• Unplug the projector from the wall outlet before cleaning. Use a dry cloth (or, for stubborn dirt or stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol cleaners, any sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.
• Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers. Do not cover the projector with a blanket, curtain, or tablecloth. If you are
246
setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and the air exhaust vent.
• Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector.
• If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation.
• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue.
• Do not store the projector outdoors for an extended length of time.
• Except as specifically explained in this manual, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
• Never open any covers on the projector except as specifically explained in this manual. Never attempt to disassemble or modify the projector. Refer all repairs to qualified service personnel.
• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: if it does not operate normally when you follow the operating instructions, or exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been damaged.
• Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.
• Unplug the projector when it will not be used for extended periods.
• Do not use the projector where it may be exposed to rain, water, or excessive humidity.
• Do not use or store the projector where it may be exposed to smoke, steam, corrosive gases, excessive dust, vibration, or shock.
• Do not use the projector where flammable or explosive gases may be present.
• Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.
• If you use the projector in a country other than where you purchased it, use the correct power cord for that country.
• Do not stand on the projector or place heavy objects on it.
247
• Do not use the projector outside of the required temperature range of 41 to 95 ºF (5 to 35 ºC). Doing so may cause an unstable display and could lead to projector damage. Do not use or store the projector where it may be exposed to sudden changes in temperature.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case.
• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
• Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected.
• Never try to remove the lamp immediately after use because it will be extremely hot. Before removing the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely.
• Do not disassemble the lamp or subject it to impacts.
• Do not place the source of an open flame, such as a lit candle, on or near the projector.
• Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or pull it excessively. Keep the power cord away from hot electrical appliances.
• If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or coming in contact with your eyes or mouth. If you do inhale gases or gases come in contact with your eyes or mouth, seek medical advice immediately.
• If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes or mouth when you open the lamp cover. If pieces of glass do get into your eyes or mouth, seek medical advise immediately.
• Always lower the volume before turning off the projector. Turning on the projector with the volume too high can damage your ears.
• Do not store the interactive pens or the batteries in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.
• Remove the batteries from the interactive pens if you will not be using the pens for a long time.
Note:
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
WARNING
: The cords included with this product contain chemicals, including lead, known to the State of
California to cause birth defects or other reproductive harm.
Wash hands after handling.
(This notice is provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.)
248
Parent topic:
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care, please make your own judgment on this product's suitability after a full evaluation.
Parent topic:
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do
249
not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Parent topic:
Wireless Telegraphy Act Regulations
The following acts are prohibited by the Wireless Telegraphy Act:
• Modifying and disassembling (including the antenna)
• Removing the label of conformance
Parent topic:
Trademarks
EPSON
®
, Instant Off
®
, and Quick Corner
® are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
BrightLink
® is a registered trademark, SizeWise
TM are service marks of Epson America, Inc.
is a trademark, and Epson Store
SM and Extra Care
SM
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI
Licensing LLC.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
Parent topic:
Open Source Software License
GNU GPL
250
This projector product includes the open source software programs which apply the GNU General Public
License Version 2 or later version ("GPL Programs").
We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product.
If you desire to receive the source code of the GPL Programs, contact Epson as described in the
User's
Guide
.
These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
The list of GPL Programs is as follows and the names of author are described in the source code of the
GPL Programs
The list of GPL Programs busybox-1.13.4
iptables-1.4.4
libgcc1(gcc-4.3.3) libstdc++-6.0.10
linux-2.6.27
patches udhcp 0.9.8
uvc rev.219
wireless_tools 29
EPSON original drivers
The GNU General Public License Version 2 is as follows. You also can see the GNU General Public
License Version 2 at http://www.gnu.org/licenses/.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
251
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the
Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".
252
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
253
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program
(or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
254
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this
License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the
Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
255
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL
ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE
THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR
DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the
"copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU
General Public License as published by the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
256
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY
NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General
Public License. Of course, the commands you use may be called something other than `show w' and
`show c'; they could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a
"copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License.
GNU LGPL
This projector product includes the open source software programs which apply the GNU Lesser
General Public License Version 2 or later version ("LGPL Programs").
We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product.
If you desire to receive the source code of the LGPL Programs, please see the "EPSON Projector
Contact List" in the User's Guide, and contact the customer support of your region.
These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
257
The list of LGPL Programs is as follows and the names of author are described in the source code of the
LGPL Programs.
LGPL Programs glibc-2.8
SDL-1.2.13
SDL-Image cairo-1.10.2
podofo-0.91
wcecompat-1.2
The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser
General Public License Version 2 at http://www.gnu.org/licenses/.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library
Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
You can use it too, but we suggest you first think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
258
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library.
Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.
This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General
Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The
Lesser General Public License permits more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.
259
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in nonfree programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these terms. A "work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
260
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
261
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4.You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the
Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the
Library and its use are covered by this License. You must supply a copy of this License. If the work
262
during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable
"work that uses the Library", as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.
263
b) Give prominent notice with the combined library of the fact that part of it is a work based on the
Library, and explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this
License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
264
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General
Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this
License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the
Library does not specify a license version number, you may choose any version ever published by the
Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR
THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,
YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL
ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE
THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A
FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
265
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General
Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser
General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a
"copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That's all there is to it!
BSD License (Berkeley Software Distribution License)
This projector product includes the open source software program "University of California, Berkeley
License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".
The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of BSD License programs
266
busybox-1.13.4
License terms of conditions of each program which are provided by owner of the copyright to the ÒBSD
LicenseÓ are as follows.
Copyright (c) The Regents of the University of California. All rights reserved.
This code is derived from software contributed to Berkeley by Kenneth Almquist.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
libjpeg
This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg".
The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of libjpeg programs libjpeg-6b
License terms of conditions of each program which are provided by owner of the copyright to the
"libjpeg" are as follows.
Copyright (C) 1994-1997, Thomas G. Lane. This file is part of the Independent JPEG Group's software.
For conditions of distribution and use, see the accompanying README file.
267
This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.
You are welcome to redistribute this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.
LEGAL ISSUES
============
In plain English:
1. We don't promise that this software works. (But if you find any bugs, please let us know!)
2. You can use this software for whatever you want. You don't have to pay us.
3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent JPEG Group".
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author's name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as
"the Independent JPEG Group's software".
We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.
268
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.)
However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does not limit you more than the foregoing paragraphs do.
The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free
Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.
It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM,
AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software.
(Since arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware, there are no patent restrictions on the remaining code.
The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the
Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders.
We are required to state that "The Graphics Interchange Format(c) is the Copyright property of
CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated." libpng
This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng".
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of libpng programs libpng-1.2.49
License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows.
For conditions of distribution and use, see copyright notice in png.h Copyright (c) 1998-2012 Glenn
Randers-Pehrson (Version 0.96 Copyright (c) 1996, 1997 Andreas Dilger) (Version 0.88 Copyright (c)
1995, 1996 Guy Eric Schalnat, Group 42, Inc.)
269
This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this sentence.
This code is released under the libpng license.
libpng version 1.2.6, August 15, 2004, through 1.2.49, March 29, 2012, are Copyright (c) 2004, 2006-
2009 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors
Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn
Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or against infringement.
There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn
Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger
Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
270
Magnus Holmgren
Greg Roelofs
Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric
Schalnat, Group 42, Inc.
For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the
PNG Reference Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and "pngbar.jpg
(88x31) and "pngnow.png" (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the
Open Source Initiative.
271
Glenn Randers-Pehrson [email protected]
March 29, 2012 zlib
This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib".
The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
List of zlib programs zlib-1.1.4
zlib-1.2.3
License terms of conditions of each program which are provided by owner of the copyright to the ÒzlibÓ are as follows.
Copyright notice:
(C) 1995-1998 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly [email protected]
Mark Adler [email protected]
272
If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.
If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
mDNSResponder
This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January 2004".
List of "mDNSResponder" mDNSResponder-107.6 (only mDNSResponderPosix is used)
License terms ÒApache License Version 2.0, January 2004" are as follows.
Apache License
Version 2.0, January 2004 http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
1. Definitions.
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by
Sections 1 through 9 of this document.
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the
License.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.
"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.
273
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the
License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.
"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to
Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity
(including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions:
(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and
274
(b) You must cause any modified files to carry prominent notices stating that You changed the files; and
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the
Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the
License.
You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such
Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this
License, without any additional terms or conditions.
Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.
6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR
A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this
License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of
275
the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof,
You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations,
You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other
Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
APPENDIX: How to apply the Apache License to your work.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!)
The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.
Copyright [yyyy] [name of copyright owner]
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License.
You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under the License.
newlib
This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib".
The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of newlib programs newlib 1.17.0
276
License terms of conditions of each program which are provided by owner of the copyright to the "newlib" are as follows.
The newlib subdirectory is a collection of software from several sources.
Each file may have its own copyright/license that is embedded in the source file. Unless otherwise noted in the body of the source file(s), the following copyright notices will apply to the contents of the newlib subdirectory:
(1) Red Hat Incorporated
Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved.
This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express permission of Red Hat, Inc.
(2) University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
*
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
*
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
*
Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
277
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(3) David M. Gay (AT&T 1991, Lucent 1998)
The author of this software is David M. Gay.
Copyright (c) 1991 by AT&T.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED
WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR AT&T MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF
THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE.
-----------
The author of this software is David M. Gay.
Copyright (C) 1998-2001 by Lucent Technologies
All Rights Reserved
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that the copyright notice and this permission notice and warranty disclaimer appear in supporting documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR
ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
(4) Advanced Micro Devices
Copyright 1989, 1990 Advanced Micro Devices, Inc.
278
This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD.
AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS
SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR
USE OF THIS SOFTWARE.
So that all may benefit from your experience, please report any problems or suggestions about this software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-
89-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.
Advanced Micro Devices, Inc.
29K Support Products
Mail Stop 573
5900 E. Ben White Blvd.
Austin, TX 78741
800-292-9263
(5)
C.W. Sandmann
Copyright (C) 1993 C.W. Sandmann
This file may be freely distributed as long as the author's name remains.
(6) Eric Backus
(C) Copyright 1992 Eric Backus
This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software.
(7) Sun Microsystems
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
(8) Hewlett Packard
(c) Copyright 1986 HEWLETT-PACKARD COMPANY
279
To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of
Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company makes no representations about the suitability of this software for any purpose.
(9) Hans-Peter Nilsson
Copyright (C) 2001 Hans-Peter Nilsson
Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.
THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
(11) Christopher G. Demetriou
Copyright (c) 2001 Christopher G. Demetriou
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(12) SuperH, Inc.
280
Copyright 2002 SuperH, Inc. All rights reserved
This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH.
SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS
SOFTWARE. IN NO EVENT SHALL SUPERH BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING,
PERFORMANCE, OR USE OF THIS SOFTWARE.
So that all may benefit from your experience, please report any problems or suggestions about this software to the SuperH Support Center via e-mail at [email protected] .
SuperH, Inc.
405 River Oaks Parkway
San Jose
CA 95134
USA
(13) Royal Institute of Technology
Copyright (c) 1999 Kungliga Tekniska Hšskolan (Royal Institute of Technology, Stockholm, Sweden).
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
281
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(14) Alexey Zelkin
Copyright (c) 2000, 2001 Alexey Zelkin <[email protected]>
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(15) Andrey A. Chernov
Copyright (C) 1997 by Andrey A. Chernov, Moscow, Russia.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
282
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(16) FreeBSD
Copyright (c) 1997-2002 FreeBSD Project.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(17) S. L. Moshier
Author: S. L. Moshier.
Copyright (c) 1984,2000 S.L. Moshier
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
283
THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED
WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NO REPRESENTATION OR WARRANTY OF
ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR
ANY PARTICULAR PURPOSE.
(18) Citrus Project
Copyright (c)1999 Citrus Project,
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(19) Todd C. Miller
Copyright (c) 1998 Todd C. Miller <[email protected]>
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
284
THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
(20) DJ Delorie (i386)
Copyright (C) 1991 DJ Delorie
All rights reserved.
Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms.
This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
(23) Intel (i960)
Copyright (c) 1993 Intel Corporation
Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.
Intel grants this permission provided that the above copyright notice appears in all copies and that both the copyright notice and this permission notice appear in supporting documentation. In addition, Intel grants this permission provided that you prominently mark as "not part of the original" any modifications made to this software or documentation, and that the name of Intel Corporation not be used in advertising or publicity pertaining to distribution of the software or the documentation without specific, written prior permission.
Intel Corporation provides this AS IS, WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Intel makes no guarantee or representations regarding the use of, or the results of the use of, the software and documentation in terms of correctness, accuracy, reliability, currentness, or otherwise; and you rely on the software, documentation and results solely at your own risk.
IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF
PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN
NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE
PRODUCT LICENSED HEREUNDER.
285
(26) Mike Barcroft
Copyright (c) 2001 Mike Barcroft <[email protected]>
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(27) Konstantin Chuguev (--enable-newlib-iconv)
Copyright (c) 1999, 2000
Konstantin Chuguev. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
286
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
iconv (Charset Conversion Library) v2.0
(28) Artem Bityuckiy (--enable-newlib-iconv)
Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic
Publishers.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(30) - Alex Tatmanjants (targets using libc/posix)
Copyright (c) 1995 Alex Tatmanjants <[email protected]> at Electronni Visti IA, Kiev, Ukraine.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
287
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(31) - M. Warner Losh (targets using libc/posix)
Copyright (c) 1998, M. Warner Losh <[email protected]>
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(32) - Andrey A. Chernov (targets using libc/posix)
Copyright (C) 1996 by Andrey A. Chernov, Moscow, Russia.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
288
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(33) - Daniel Eischen (targets using libc/posix)
Copyright (c) 2001 Daniel Eischen <[email protected]>.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(35) - ARM Ltd (arm and thumb variant targets only)
Copyright (c) 2009 ARM Ltd
289
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the company may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY ARM LTD "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(36) - CodeSourcery, Inc.
Copyright (c) 2009 CodeSourcery, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
*
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
*
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
*
Neither the name of CodeSourcery nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
290
/*
*
THIS SOFTWARE IS PROVIDED BY CODESOURCERY, INC. "AS IS" AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AREDISCLAIMED. IN NO
EVENT SHALL CODESOURCERY BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
(37) MIPS Technologies, Inc
Copyright (c) 2009 MIPS Technologies, Inc.
*
*
*
*
All rights reserved.
*
*
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
*
*
*
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
*
*
291
Neither the name of MIPS Technologies Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
*
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
/*
WPA Supplicant
The copyright owner of the WPA Supplicant open source software provides terms and conditions
(hereinafter referred to as "WPA Supplicant License"). The projector uses this product in compliance with the BSD License, as part of the WPA Supplicant License.
The "WPA Supplicant License" is WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of WPA Supplicant License programs
WPA Supplicant-0.7.3
License terms of conditions of each program which are provided by owner of the copyright to the "WPA
Supplicant License" are as follows.
Copyright (c) 2003-2011, Jouni Malinen <[email protected]> and contributors All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name(s) of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
292
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
For MPEG-4 ASP:
With respect to a Licensee offering MPEG-4 Video Decoders and/or Encoders the following notice shall be given: THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO
LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i)
ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO")
AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR
SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE
OBTAINED FROM MPEG LA,LLC. SEE HTTP://WWW.MPEGLA.COM.
For MPEG-4 AVC:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
For WMV/WMA (Microsoft):
This product is protected by certain intellectual property rights of Microsoft.
Use or distribution of such technology outside of this product is prohibited without a license from
Microsoft.
For VC-1
THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE VC-1 STANDARD ("VC-1 VIDEO") AND/OR (ii)DECODE VC-1 VIDEO THAT
293
WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
MIT License
This projector product includes the open source software program which applies the terms and conditions provided by owner of the copyright to the "MIT License".
The "MIT License" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of MIT License programs pixman-0.21.6
License terms of conditions of each program which are provided by owner of the copyright to the "MIT
License" are as follows.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
The following is the MIT license, agreed upon by most contributors.
Copyright holders of new code should use this license statement where possible. They may also add themselves to the list below.
Copyright 1987, 1988, 1989, 1998 The Open Group
Copyright 1987, 1988, 1989 Digital Equipment Corporation
Copyright 1999, 2004, 2008 Keith Packard
Copyright 2000 SuSE, Inc.
294
Copyright 2000 Keith Packard, member of The XFree86 Project, Inc.
Copyright 2004, 2005, 2007, 2008, 2009, 2010 Red Hat, Inc.
Copyright 2004 Nicholas Miell
Copyright 2005 Lars Knoll & Zack Rusin, Trolltech
Copyright 2005 Trolltech AS
Copyright 2007 Luca Barbato
Copyright 2008 Aaron Plattner, NVIDIA Corporation
Copyright 2008 Rodrigo Kumpera
Copyright 2008 Andre Tupinamb‡
Copyright 2008 Mozilla Corporation
Copyright 2008 Frederic Plourde
Copyright 2009, Oracle and/or its affiliates. All rights reserved.
Copyright 2009, 2010 Nokia Corporation.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice (including the next paragraph) shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
TOPPERS/JSP
This projector product includes the open source software program " TOPPERS/JSP " which applies the terms and conditions provided by owner of the copyright to the " TOPPERS/JSP ".
The " TOPPERS/JSP " are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of TOPPERS/JSP programs
295
jsp-1.4.3
License terms of conditions of each program which are provided by owner of the copyright to the "
TOPPERS/JSP " are as follows.
TOPPERS/JSP Kernel
Toyohashi Open Platform for Embedded Real-Time Systems/Just Standard Profile Kernel
Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of
Technology, JAPAN
Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory
Graduate School of Information Science, Nagoya Univ., JAPAN.
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the conditions described in Version 2 of the GNU Public License officially announced by the Free Software
Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization) of this software (this software includes alterations, likewise below) without compensation.
(1) When this software is utilized in the form of source code, the above copyright declaration, these conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged form inside the source code.
(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).
(3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc., one of the following conditions shall be satisfied.
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).
(b) The TOPPERS Project shall be notified owing to a method in which the form of distribution is decided otherwise.
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
This software is something that is provided with no guarantee. The above copyright holder and the
TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
296
Note: The TOPPERS License has been revised several times; what is shown above is the latest version that is to be applied to software made public hereafter.
TINET
This projector product includes the open source software program " TINET" which applies the terms and conditions provided by owner of the copyright to the " TINET ".
The " TINET " are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of TINET programs tinet-1.4.4
License terms of conditions of each program which are provided by owner of the copyright to the " TINET
" are as follows.
(1) FreeBSD
Copyright (c) 1980, 1986, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement:
This product includes software developed by the University of California, Berkeley and its contributors.
4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
297
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
(6) TINET and TOPPERS
TINET (TCP/IP Protocol Stack)
Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of
Technology, JAPAN
TINET (TCP/IP Protocol Stack)
Copyright (C) 2001-2006 by Dep. of Computer Science and Engineering Tomakomai National College of
Technology, JAPAN
The above copyright holder, limited to cases in which one satisfies conditions (1) ~ (4) below, or the conditions described in Version 2 of the GNU Public License officially announced by the Free Software
Foundation, consents to the use, reproduction, alteration, and redistribution (hereafter called utilization) of this software (this software includes alterations, likewise below) without compensation.
(1) When this software is utilized in the form of source code, the above copyright declaration, these conditions of utilization, and the following stipulation of no guarantee shall be included in unchanged form inside the source code.
(2) When this software is redistributed in a form in which it can be used in the development of other software, library form, etc., the above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).
(3) When this software is redistributed in a form in which it cannot be used in the development of other software, embedded in devices, etc., following conditions shall be satisfied.
(a) The above copyright display, these terms of utilization, and the following stipulation of no guarantee shall be inserted in documentation accompanying redistribution (user's manual, etc.).
(4) The above copyright holder and the TOPPERS Project shall be exempt from responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
This software is something that is provided with no guarantee. The above copyright holder and the
TOPPERS Project make no guarantee whatsoever in regard to this software, including the possibility of its application. In addition, the above copyright holder and the TOPPERS Project shall also not bear responsibility for whatever damages occur either directly or indirectly through the utilization of this software.
Parent topic:
298
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
This information is subject to change without notice.
A Note Concerning Responsible Use of Copyrighted Materials
Parent topic:
A Note Concerning Responsible Use of Copyrighted Materials
Epson encourages each user to be responsible and respectful of the copyright laws when using any
Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.
Parent topic:
Copyright Attribution
This information is subject to change without notice.
© 2014 Epson America, Inc.
2/14
CPD-38228R2
Parent topic:
299
advertisement
Key Features
- Short throw Short throw projector White
- 3LCD 3100 ANSI lumens
- Lamp 3500 h
- WXGA (1280x800) 16:10 3000:1
- Screen size compatibility: 1524 - 2540 mm (60 - 100") Number of colours: 1.073 billion colours
- Focus: Manual
- Ethernet LAN Wi-Fi
- Built-in speaker(s) 10 W
- AC 322 W
Related manuals
advertisement