Toshiba PS100 Owner Manual

PORTÉGÉ S100

TOSHIBA

PORTÉGÉ S100

Portable Personal Computer

User’s Manual

ii

User’s Manual

Copyright

© 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

TOSHIBA PORTÉGÉ S100 Portable Personal Computer User’s Manual

First edition May 2005

Copyright authority for music, movies, computer programs, data bases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author’s rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA

PORTÉGÉ S100 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual. Graphics processor performance may vary considerably from specifications due to design configuration.

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International

Business Machines Corporation.

Intel, Intel SpeedStep, Pentium and Centrino are trademarks or registered trademarks of Intel Corporation.

Windows and Microsoft are registered trademarks of Microsoft Corporation.

Photo CD is a trademark of Eastman Kodak.

Sonic and RecordNow! are registered trademark of Sonic Solutions.

i.LINK is a trademark of Sony Corporation.

InterVideo and WinDVD are registered trademarks of InterVideo Inc.

WinDVD Creator is trademark of InterVideo Inc.

Other trademarks and registered trademarks not listed above may be used in this manual.

User’s Manual

User’s Manual

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related

European Directives. Responsible for CE-Marking is TOSHIBA Europe

GmbH, Hammfelddamm 8, 41460 Neuss, Germany.

The complete and official EU Declaration of Conformity can be found on

TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone

Network (PSTN).

However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17

Greece ATAAB AN005,AN006 and GR01,02,03,04

AN001,005,006,007,011

P03,04,08,10

Spain

Switzerland

ATAAB AN005,007,012, and ES01

ATAAB AN002

All other countries/regions ATAAB AN003,004

Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate national type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.

User’s Manual iii

User’s Manual

Description on Laser specification

The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

APPAREIL A LASER DE CLASSE 1

KLASS 1 LASER APPARAT

The drive with the above label is certified by the manufacturer that the drive complies with the requirement for laser product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the

United States of America, Department of Health & Human Services,

Food and Drug Administration.

In other countries, the drive is certified to comply with the requirement pursuant to IEC 825 and EN60825 on class 1 laser product.

This computer is equipped with the optical drive in the following list according to the model purchased.

Manufacturer

MATSUSHITA

MATSUSHITA

Type

UJDA765

UJ-822 iv User’s Manual

PORTÉGÉ S100

Table of Contents

General Precautions

Preface

Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Chapter 1 :

Introduction

Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Special features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Chapter 2 :

The Grand Tour

Front with the display closed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Underside. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Chapter 3 :

Getting Started

Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Restarting the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Restoring the preinstalled software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

User’s Manual v

Table of Contents

Chapter 4 :

Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Using the USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Changing Ultra Slim Bay modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Writing CDs on DVD-ROM&CD-R/RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

Writing CD/DVDs on DVD Super Multi drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-18

Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-21

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23

LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25

Cleaning the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-31

Chapter 5 :

The Keyboard

Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9

Chapter 6 :

Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3

Care and use of the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14

Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-16

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17

System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17

Chapter 7 :

HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

HW Setup window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Configuring the Execute-Disable Bit Capability and TPM. . . . . . . . . . . . . . . . . . . . .7-8 vi User’s Manual

Table of Contents

Chapter 8 :

Optional Devices

PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

SD card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Hard disk drive pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Ultra Slim Bay HDD adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Advanced Port Replicator IIl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

Parallel printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

Chapter 9 :

Troubleshooting

Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

Appendix A :

Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B :

Display Controller and Modes

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C :

Wireless LAN

Card Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Supported Frequency Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Appendix D :

TOSHIBA RAID

Setting up Windows Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

Starting, Modifying and Ending the BIOS Setup Program . . . . . . . . . . . . . . . . . . . D-4

Appendix E :

AC Power Cord and Connectors

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F :

If your computer is stolen

Glossary

Index

User’s Manual vii

Table of Contents viii User’s Manual

PORTÉGÉ S100

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Stress injury

Carefully read the Instruction Manual for Safety & Comfort . It contains information on prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard use. Chapter 3, Getting Started , also includes information on work space design, posture and lighting that can help reduce physical stress.

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, or if you keep your hands on the palm rest, for example) your skin might suffer low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with the metal plate supporting the I/O ports. It can become hot.

■ The surface of the AC adaptor can become hot when in use. This condition does not indicate a malfunction. If you need to transport the

AC adaptor, disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat.

The material could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.

Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions.

User’s Manual ix

General Precautions

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.

Mobile phones

Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.

Disclaimers

LCD

Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology.

Maximum brightness is only available when operating in AC power mode.

Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.

CPU

Central Processing Unit (“CPU”) Performance Disclaimer.

CPU performance in your computer product may vary from specifications under the following conditions:

■ use of certain external peripheral products

■ use of battery power instead of AC power

■ use of certain multimedia, computer generated graphics or video applications

■ use of standard telephone lines or low speed network connections

■ use of complex modeling software, such as high end computer aided design applications

■ use of several applications or functionalities simultaneously

■ use of computer in areas with low air pressure

(high altitude >1,000 meters or >3,280 feet above sea level)

■ use of computer at temperatures outside the range of 5°C to 30°C

(41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your PC documentation or visit the

Toshiba website at www.pcsupport.toshiba.com for details).

CPU performance may also vary from specifications due to design configuration.

x User’s Manual

User’s Manual

General Precautions

Under some conditions, your computer product may automatically shut-down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in Chapter 9 Troubleshooting for more information.

Copy Protection

Copy protection technology included in certain media may prevent or limit recording or viewing of the media.

HDD Drive Capacity

1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of

1 GB = 1024 × 1024 × 1024 = 1,073,741,824 bytes, and therefore may show less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as

Microsoft Operating System and/or pre-installed software applications, or media content. Actual formatted capacity may vary.

Non-applicable Icons

Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.

xi

General Precautions xii User’s Manual

PORTÉGÉ S100

Preface

Congratulations on your purchase of the PORTÉGÉ S100 computer.

This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing.

This manual tells how to set up and begin using your PORTÉGÉ S100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read over the Introduction and The Grand Tour chapters to familiarize yourself with the computer’s features, components and accessory devices.

Then read Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to look over the

Special features section of the Introduction, to learn about features that are uncommon or unique to the computers and carefully read HW Setup .

If you are going to install PC cards or connect external devices such as a monitor, be sure to read Chapter 8, Optional Devices .

Manual contents

This manual is composed of the following nine chapters, six appendixes, a glossary and an index.

Chapter 1, Introduction , is an overview of the computer’s features, capabilities, and options.

Chapter 2, The Grand Tour , identifies the components of the computer and briefly explains how they function.

Chapter 3, Getting Started , provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.

User’s Manual xiii

Preface

Chapter 4, Operating Basics , includes instructions on using the following devices: Touch Pad, USB floppy disk drive (optional), Ultra Slim Bay modules, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs.

Chapter 5, The Keyboard , describes special keyboard functions including the keypad overlay and hot keys.

Chapter 6, Power and Power-Up Modes , gives details on the computer’s power resources and battery save modes and how to set a password.

Chapter 7, HW Setup , explains how to configure the computer using the

HW Setup program.

Chapter 8, Optional Devices , describes the optional hardware available.

Chapter 9, Troubleshooting , provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.

The Appendixes provide technical information about your computer.

The Glossary defines general computer terminology and includes a list of acronyms used in the text.

The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only

Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key.

xiv User’s Manual

Preface

Key operation

Some operations require you to simultaneously use two or more keys.

We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C . If three keys are used, hold down the first two and at the same time press the third.

ABC When procedures require an action such as clicking an icon or entering text, the icon’s name or the text you are to type in is represented in the type face you see to the left.

Display

S

ABC

Names of windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.

Please read. A note is a hint or advice that helps you make best use of your equipment.

Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.

User’s Manual xv

Preface xvi User’s Manual

PORTÉGÉ S100

Chapter 1

Introduction

This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories.

Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for future use.

Hardware

Check to make sure you have all the following items:

■ PORTÉGÉ S100 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Modular cable for modem (optional)

User’s Manual 1-1

Introduction

Software

Microsoft

®

Windows XP Professional

■ The following software is preinstalled:

■ Microsoft

®

Windows XP Professional

■ Microsoft Internet Explorer

■ TOSHIBA Utilities

■ TOSHIBA SD Memory Boot Utility

■ DVD Video Player

■ TOSHIBA Touch pad On/Off utility

■ TOSHIBA Power Saver

■ TOSHIBA Mobile Extension

■ TOSHIBA Assist

■ TOSHIBA ConfigFree

■ TOSHIBA Zooming Utility

■ TOSHIBA PC Diagnostic Tool

■ TOSHIBA Controls

■ TOSHIBA Mic Effect

■ TOSHIBA Password Utility

■ TOSHIBA RAID Utility

■ Online manual

Documentation and Backup Media

■ PORTÉGÉ S100 Portable Personal Computer User's Manual

■ PORTÉGÉ S100 Quickstart

■ Instruction Manual for Safety & Comfort

■ Warranty information

■ Product Recovery DVD-ROM

If any of the items are missing or damaged, contact your dealer immediately.

1-2 User’s Manual

Introduction

Features

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),

Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:

Processor

Built-in The computer is equipped with an Intel ®

Pentium ® M processor, which incorporates a

64 KB level 1 cache memory and a 2 MB level 2 cache memory. It also supports Enhanced Intel ®

SpeedStep TM technology.

Some models of the computers carry Intel ® Centrino ™ technology, which is based on three separate technologies of Intel ® Pentium ® M,

Intel ® PRO/Wireless Network Connection, and Intel ® 915 Chipset Family.

Intel ® 915 Chipset Family is a model by whom Intel ® Pentium processor is installed.

® M

Memory

Slots

Video RAM

A 256, 512 or 1,024 MB memory module is installed in the main memory slot for system memory.

The expansion memory slot accommodates another 256, 512 or 1,024 MB memory module.

The maximum capacity of installable memory results as follows:

■ Built-in memory is 256 MB: A maximum of

1,280 MB

■ Built-in memory is 512 MB: A maximum of

1,536 MB

■ Built-in memory is 1,024 MB: A maximum of

2,048 MB

64 MB of RAM is provided for video display.

User’s Manual 1-3

Introduction

Power

Battery pack

RTC battery

AC adaptor

The computer is powered by one rechargeable lithium-ion battery pack.

The internal RTC battery backs up the Real Time

Clock (RTC) and calendar.

The AC adaptor provides power to the system and recharges the batteries when they are low.

It comes with a detachable power cord.

It encloses 2-pin plug or 3-pin plug type.

Because it is universal, it can receive a range of

AC voltage from 100 to 240 volts; however, the output current varies among different models.

Using the wrong model can damage your computer. Refer to the AC adaptor section in

Chapter 2, The Grand Tour.

Disks

Hard disk drive

USB floppy disk drive (optional)

Available in three sizes.

■ 40.0 billion bytes (37.26 GB)



Other hard disk drives may be introduced.

Accommodates either 3 1/2" 1.44-megabyte or

720-kilobyte floppy disks. It connects to a USB port.

Computers in this series can be configured with an optical media drive installed in the Ultra Slim Bay. The available optical media drives are described below.

1-4 User’s Manual

User’s Manual

Introduction

DVD-ROM&CD-R/RW drive

DVD Super Multi drive

Some models are equipped with a full-size,

DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads

DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum

24 speed. The drive supports the following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

Some models are equipped with a full-size DVD

Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either

12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum

24 speed. It writes CD-R at maximum 24 speed,

CD-RW at maximum 10 speed, DVD-R at maximum 2 speed, DVD-RW at maximum

2 speed. DVD+R and DVD+RW at maximum

2.4 speed. DVD-RAM at maximum 2 speed. This drive supports the following formats in addition to

DVD-ROM&CD-R/RW drive.

■ DVD-R

■ DVD-RW

■ DVD+R

■ DVD+RW

■ DVD-RAM

1-5

Introduction

Display

The computer’s LCD display panel supports high-resolution video graphics.

The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability.

Built-in 14.1" TFT LCD screen, 16 M colors, with one of the following resolutions:

■ XGA, 1024 horizontal × 768 vertical pixels

■ SXGA+, 1400 horizontal × 1050 vertical pixels

Graphics controller Graphics controller maximizes display performance. Refer to Display Controller and

Modes section in Appendix B for more information.

Keyboard

Built-in 85 keys or 86 keys, compatible with IBM

® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys.

Refer to Chapter 5, The Keyboard , for details.

Pointing Device

Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows.

Ports

External monitor

Universal Serial Bus

(USB 2.0)

Analog VGA port supports VESA DDC2B compatible functions.

The computer has two Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1).

Docking interface This port enables connection of an optional

Advanced Port Replicator III described in the

Options section.

i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras.

1-6 User’s Manual

User’s Manual

Introduction

Infrared The serial infrared port is compatible with

Infrared Data Association (IrDA 1.1) standards.

It enables cableless 4 Mbps, 1.152 Mbps,

115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or

9.6 kbps data transfer with IrDA 1.1 compatible external devices.

Slots

PC card

SD card

The PC card slot accommodates a Type II card.

This slot lets you easily transfer data from devices, such as digital cameras and

Personal Digital Assistants, that use SD card flash-memory.

Refer to Chapter 8, Optional Devices .

Multimedia

Sound system

Headphone jack

Microphone jack

Windows sound system compatible sound system provides internal speakers and a microphone as well as jacks for an external microphone and headphones.

A 3.5 mm mini headphone jack enables connection of stereo headphones.

A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.

Communications

Modem

LAN

An internal modem provides capability for data and fax communication. It supports V.90 (V.92).

The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of

V.90 and V.92 are supported only in USA,

Canada, UK, France, Germany and Australia.

Only V.90 is available in other regions.

The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T),

Fast Ethernet LAN (100 megabits per second,

100BASE-TX) and Gigabit Ethernet LAN

(1000 megabits per second, 1000BASE-T).

1-7

Introduction

Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct

Sequence Spread Spectrum/Orthogonal

Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard

(Revision A, B or G).

■ Theoretical maximum speed:

54Mbps(IEEE802.11a, 802.11g)

■ Theoretical maximum speed:

11Mbps(IEEE802.11b)

■ Frequency Channel Selection

(5 GHz: Revision A / 2.4 GHz: Revision B/G)

■ Roaming over multiple channels

■ Card Power Management

■ Wired Equivalent Privacy (WEP) data encryption, based on 128 bit encryption algorithm (Intel module type).

■ Wi-Fi Protected Access (WPA).

■ The numerical values for display are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the Wireless LAN and the distance over which Wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.

The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard. The actual transmission speed will be lower than the theoretical maximum speed.

Wireless communication switch

Ultra Slim Bay

Modules

Ultra Slim Bay

Weight Saver

This switch turns the Wireless LAN functions on and off.

Ultra Slim Bay is a single-drive bay that accommodates a DVD-ROM&CD-R/RW drive,

DVD Super Multi drive and secondary hard disk drive. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system.

To reduce weight, the Ultra Slim Bay module can be removed and a weight saver installed.

1-8 User’s Manual

Introduction

Security

Security lock slot

Ultra Slim Bay lock

Connects an optional security lock to anchor the computer to a desk or other large object.

Ultra Slim Bay module can be secured by Ultra

Slim Bay lock fixed with a lock screw in the lock position. The lock screw is inserted in the unlock position when purchased.

Special features

The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.

TOSHIBA Assist button

TOSHIBA

Presentation button

Hot keys

Display automatic power off

HDD automatic power off

System automatic

Standby/Hibernation

Keypad overlay

Press this button to launch an application automatically. The default is TOSHIBA Assist.

Press this button to change internal display, external display, simultaneous display, or multi-monitor display.

Key combinations let you quickly change the system configuration directly from the keyboard without running a system configuration program.

This feature automatically cuts off power to the computer’s LCD display panel when there is no keyboard input for a time specified. Power is restored when any key is pressed. You can specify the time in the Monitor power off item of the Basic Setup tab in TOSHIBA Power Saver.

This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified. Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA

Power Saver.

This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System hibernation in the System standby and System item of the Basic

Setup tab in TOSHIBA Power Saver.

A ten-key pad is integrated into the keyboard.

Refer to the Keypad overlay section in Chapter 5,

The Keyboard, for instructions on using the keypad overlay.

User’s Manual 1-9

Introduction

1-10

Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer.

Instant security A hot key function blanks the LCD screen and disables the computer providing data security.

Intelligent power supply

Battery save mode

A microprocessor in the computer’s intelligent power supply detects the battery’s charge and calculates the remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item in

TOSHIBA Power Saver.

This feature lets you save battery power. You can specify the Power Save Mode in the Profile item in TOSHIBA Power Saver.

Panel power on/off This feature turns power to the computer off when the computer’s LCD display panel is closed and turns it back on when the computer’s LCD display panel is opened. You can specify the setting in the When I close the lid item of the

Setup Action tab in TOSHIBA Power Saver.

Low battery automatic hibernation

When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation and shuts down. You can specify the setting in the

Setup Action tab in TOSHIBA Power Saver.

Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.

■ Maximum

Performance

■

■

Performance

Battery optimized

Turns on fan first, then if necessary lowers CPU processing speed.

Uses a combination of fan and lowering the

CPU processing speed.

Lowers the CPU processing speed first, then if necessary turns on the Cooling Method.

User’s Manual

User’s Manual

Introduction

Optical media drive power icon

HDD Protection

Use this to turn the power of the optical media drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off. If the optical media drive power is off, the disc tray will not open even if the eject button is pushed. The power of the optical media drive can be turned on using the optical media drive icon.

Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and those signs in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact. Refer to the Using the Hard

Disk Drive (HDD) Protection section in Chapter 4,

Operating Basics, for details.

This function does not guarantee that the HDD will not be damaged.

Hibernation

Standby

TOSHIBA RAID

This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the

Turning off the power section in Chapter 3,

Getting Started, for details.

If you have to interrupt your work, you can turn off the power without exiting from your software.

Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.

RAID (Redundant Array of Independent Disks) realizes fault tolerance (mirroring = RAID1), which is configured by arraying multiple independent hard disk drives. This feature is only available when a secondary hard disk drive is installed in the Ultra Slim Bay.

1-11

Introduction

Utilities

This section describes preinstalled utilities and tells how to start them.

For details on operations, refer to each utility’s online manual, help files or readme.txt files.

TOSHIBA Power

Saver

HW Setup

TOSHIBA Controls

DVD Video Player

TOSHIBA SD

Memory Boot Utility

TOSHIBA Zooming

Utility

RecordNow! Basic for TOSHIBA

To access this power savings management program, click start , click Control Panel , click Performance and Maintenance and select the TOSHIBA Power Saver icon.

This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, To access this utility, click start , click Control Panel , click Printers and Other

Hardware and select the TOSHIBA HWSetup icon.

This utility have a section to let you do the following:

■ Buttons: Assign applications or functions to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist).

The DVD Video Player is used to play

DVD-Video. It has an on-screen interface and functions. Click start , point to All Programs , point to InterVideo WinDVD , then click

InterVideo WinDVD .

The TOSHIBA SD memory boot utility is a utility which can create SD memory card to a boot disk.

You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows. Click start , point to

All Programs , point to TOSHIBA , point to

Utilities and click SD Memory Boot Utility .

This utility allows you to enlarge or reduce the icon size on the desktop or the application window.

You can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CD/DVDs to store the files and folders on your hard disk drive.

This software can be used on a model with

DVD-ROM&CD-R/RW drive and DVD Super

Multi drive.

1-12 User’s Manual

User’s Manual

Introduction

TOSHIBA Assist

TOSHIBA PC

Diagnostic Tool

TOSHIBA Assist is a graphical user interface that provides easy access to help and services. It is the default function launched by the TOSHIBA

Assist button.

TOSHIBA PC Diagnostic Tool displays the basic information on PC, and the test of built-in devices can also be performed. To start TOSHIBA PC

Diagnostic Tool, click start , point to All

Programs , point to TOSHIBA , point to Utilities and click PC Diagnostic Tool .

TOSHIBA Mobile

Extension

This utility supports docking your computer to an optional Advanced Port Repricator III. To open the property dialog, select TOSHIBA Mobile

Extension from TOSHIBA Assist.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks. To start

ConfigFree, click start , point to All Programs , point to TOSHIBA , point to Networking and click

ConfigFree .

TOSHIBA Touch Pad

On/Off Utility

This utility has the following function.

To disable/enable the Touch Pad with

Fn + F9 key.

TOSHIBA Mic Effect This utility provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network.

Refer to the Sound System section in Chapter 4,

Operating Basics, for details.

1-13

Introduction

TOSHIBA RAID

Console

NVIDIA Rotation

Settings

TOSHIBA Password

Utility

Sound drivers

If a secondary hard disk drive is installed in the

Ultra Slim Bay in addition to the built-in HDD, you can use the TOSHIBA RAID Console to create or manage a RAID array.

To start the utility, click start , point to All

Programs , point to TOSHIBA , point to RAID and click RAID Console .

It is possible to change to RAID1 (mirroring) from a non-RAID configuration (default).

Caution: When RAID1 is set, you cannot change your setting unless you completely restore your preinstalled software.

It is strongly recommended to read the TOSHIBA

RAID Help before you change any of the settings.

This utility let you rotate the desktop by 0 and

180 easily. It can rotate by clicking the icon in a taskbar or pressing Ctrl + Shft + R .

In a multi-monitor setup, the display that contains the cursor is effective.

This utility lets you set a password that restricts access to the computer.

A broad range of audio controls are available through the ADI sound driver, including Software

Synthesize, Mic Volume, Noise Reduction and

Audio Power Management.

Click start , click Control Panel and click

SoundMAX icon to change the Mic Noise

Reduction settings and the Power Management settings. If you are viewing the Control Panel in

Category View, click on Switch to Classic View .

For other sound settings, use the Windows

Device Manager, Multimedia Panel or Volume

Dial.


User’s Manual

Introduction

TOSHIBA

Accessibility

DLA for TOSHIBA

TOSHIBA Hotkey

Utility for Display

Devices

TOSHIBA SD

Memory Card Format

CD/DVD Drive

Acoustic Silencer

This utility lets you make the Fn key sticky, that is, you can press it once, release it, and they press an “ F number ” key. The Fn key remains active until another key is pressed.

DLA (Drive Letter Access) is the packet writing software which provides the function which writes files and/or folders to DVD-RW, CD-RW and

DVD+RW discs via a drive letter like a floppy disk or other removable disks.

This utility has the change of a display device, and the function to change display resolution.

Press Fn + F5 to change the active display device. Press Fn + Space keys to change the display resolution.

This utility has the function which formats SD memory card by SD standard format.

This utility has the function to set up the read speed of CD.

It is ineffective in DVD.

You can set up one of the modes: [Normal Mode] can read data early, and [Quiet Mode] can lessen noise.

1-15

Introduction

Options

You can add a number of options to make your computer even more powerful and convenient to use. The following options are available:

Memory expansion

Battery pack

High capacity battery pack

A 256, 512 or 1,024 MB memory module

(DDR2-533/400) can easily be installed in the computer.

An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.

An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.

AC adaptor

Battery charger

Security lock A slot is available to attach a security cable to the computer to deter theft.

USB floppy disk Kit USB floppy disk drive accommodates

1.44-megabyte or 720-kilobyte floppy disk.

It connects to a USB port. (You cannot format

720-kilobyte floppy disks on Windows XP, but you can use previously formatted disks.)

Advanced Port

Replicator III

If you use your computer at more than one site frequently, it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you.

The battery charger lets you charge extra batteries outside the computer.

Hard disk drive

Wireless LAN Kit

The Advanced Port Replicator III provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™

(IEEE1394) port, line-in jack and line-out jack,

External monitor port, Universal Serial Bus port

(USB2.0) × 4, LAN jack, Modem jack, Serial port,

Parallel port.

You can increase your computer's data storage capacity with additional hard disk drives.

They are available in the following sizes:

■ 40 billion bytes (37.26 GB)



This option enables wireless LAN functions in computers that do not have wireless preinstalled.

It is installed by dealers only.


Introduction

Ultra Slim Bay options

The following modules can be installed in the Ultra Slim Bay. All other modules are options.

DVD-ROM&CD-R/RW Refer to the Features section for details.

DVD Super Multi

Ultra Slim Bay HDD adaptor (Black)

Refer to the Features section for details.

An adaptor lets you install an optional HDD described in Chapter 8, Optional Devices .

Hard disk drive You can increase your computer’s data storage capacity with an additional 40 billion bytes

(37.26 GB), 60 billion bytes (55.89 GB),

80 billion bytes (74.53 GB) hard disk drive in the

Ultra Slim Bay HDD adaptor.

Ultra Slim Bay Case Store the DVD Super Multi drive unit in this case when removing it from the computer or transporting it.

User’s Manual 1-17

Introduction


PORTÉGÉ S100

Chapter 2

The Grand Tour

This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.

Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.

Front with the display closed

The following figure shows the computer’s front with its LCD display panel in the closed position.

System indicators

Microphone jack Headphone jack Display latch

User’s Manual

Wireless communication switch Volume control Infrared port

Front of the computer with LCD display panel closed

Microphone

System indicators

Wireless communication switch

LEDs let you monitor the status of various computer functions. Details are given in the

System indicators section.

Slide this switch to the left to turn off Wireless

LAN function. Slide it to the right to turn on the functions.

Some models are equipped with Wireless communication.

2-1

The Grand Tour

Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off.

Microphone jack

Headphone jack

A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.

A 3.5 mm mini headphone jack enables connection of stereo headphones.

Volume control

Display latch

Infrared port

Microphone

Use this dial to adjust the volume of the stereo speakers and the stereo headphones.

This latch secures the LCD panel in its closed position. Push the latch to open the display.

This infrared port is compatible with Infrared Data

Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.15 Mbps, 115.2 kbps,

57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices.

A built-in microphone lets you record sound into your applications. Refer to the Using the microphone section in Chapter 4, Operating

Basics.

Left side

The following figure shows the computer’s left side.

LAN active indicator (orange)

LAN jack

Cooling vents

Security lock slot

PC card eject button

PC card slot

2-2

Link indicator (green) i.LINK (IEEE1394) port

The left side of the computer

SD card slot

User’s Manual

The Grand Tour

User’s Manual

LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet

LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). The LAN has two indicators. Refer to Chapter 4, Operating Basics , for details.

■ Do not connect any cable other than a LAN cable to the LAN jack.

It could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction.

Link indicator

(green)

LAN active indicator

(orange)

Cooling vents

This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly.

This indicator glows orange when data is being exchanged between the computer and the LAN.

Cooling vents help CPU keep from overheating.

Do not block the cooling vents. Do not insert or allow foreign objects to enter the cooling vents. If pins or similar objects are inserted into the computer, the computer’s circuitry may be damaged.

Security lock slot i.LINK (IEEE1394) port

A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft.

Connect an external device, such as a digital video camera to this port for high-speed data transfer.

PC card slot The PC card slot can accommodate a Type II card. The slot supports 16-bit PC cards and

CardBus PC cards.

PC card eject button This is a button for taking out PC card from a PC card slot.

Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry.

SD card slot SD cards are used in a wide variety of external devices. This slot lets you transfer data from the device to your computer.

2-3

The Grand Tour

Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry.

Right side

The following figure shows the computer’s right side.

Ultra Slim Bay

Ultra Slim Bay

External monitor port

The right side of the computer

External monitor port

A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be installed in the Ultra Slim Bay. A weight saver can be installed when there is no module.

This external monitor port lets you connect an external video display.

Back side

The following figure shows the computer’s back side.

DC IN 15V jack Modem jack

2-4

USB ports

The back side of the computer

Universal Serial Bus

(USB 2.0) ports

Two Universal Serial Bus ports are on the back side. The ports comply with the USB 2.0 standard, which enables data transfer speeds

40 times faster than the USB 1.1 standard

(The ports also support USB 1.1).

User’s Manual

The Grand Tour

Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry.

Operation of all functions of all USB devices has not been confirmed.

Some functions might not execute properly.

DC IN 15V jack

Modem jack

The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.

The modem jack lets you use a modular cable to connect the modem directly to a telephone line.

■ In case of a lightning storm, unplug the modular cable from the telephone jack.

■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.

Underside

The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer.

Notches

Battery lock

Battery pack

Battery release latch

Ultra Slim Bay

Ultra Slim Bay lock

Docking

Interface

Memory module cover

User’s Manual

HDD pack cover screw

The underside of the computer

Ultra Slim Bay lock screw

2-5

The Grand Tour

Battery lock

Battery pack

Notches

Battery release latch

Slide this lock to release the battery pack for removal.

The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to

Chapter 6, Power and Power-Up Modes .

Notches on the computer engage hooks on the

Advanced Port Replicator III to hold the connection securely.

Slide and hold this latch to release the battery pack for removal.

For detailed information on removing the battery packs, refer to Chapter 6, Power and Power-Up

Modes .

Docking interface This port enables connection of an optional

Advanced Port Replicator III described in Chapter 8,

Optional Devices .

Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer's circuitry. A plastic shutter protects the connector.

Ultra Slim Bay See the Right side section in this chapter for details.

Ultra Slim Bay lock

Slide the lock to release or secure the Ultra Slim Bay ejector.

Be sure to lock the Ultra Slim Bay lock before you transport or carry the computer.

Ultra Slim Bay lock screw

Memory module cover

HDD pack cover screw

One screw secures the Ultra Slim Bay lock.

This cover protects one of the memory module sockets. The other memory module is located under the keyboard. Refer to the Memory expansion section in Chapter 8, Optional Devices.

One screw secures the HDD cover.

2-6 User’s Manual

The Grand Tour

Front with the display open

This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, push the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.

Display hinge

LCD screen

Stereo speaker (Right)

User’s Manual

Touch Pad

Stereo speaker

(Left)

Power button

LCD Sensor switch

(Not shown)

Touch Pad control buttons

TOSHIBA Assist Button

TOSHIBA Presentation Button

The front of the computer with the LCD panel open

Display hinge

LCD screen

The display hinge holds the LCD display panel at easy-to-view angles.

The LCD screen displays high-contrast text and graphics.

The available resolution depends on the model. With XGA, you can change the resolution between 800 × 600 and

1024 × 768 pixels. With SXGA, between

800 × 600 and 1400 × 1050 pixels.

Refer to Display Controller and Modes section in

Appendix B.

When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power.

The lower brightness level is intended to save battery power.

2-7

The Grand Tour

Stereo speakers

Touch Pad control buttons

Touch Pad

TOSHIBA

Presentation button

TOSHIBA Assist button

The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.

Control buttons below the Touch Pad let you select menu items or manipulate text and graphics designated by the on-screen pointer.

A Touch Pad located in the center of the palm rest is used to control the on-screen pointer.

Refer to the Using the Touch Pad section in

Chapter 4, Operating Basics.

Press this button to change internal display, simultaneous display, or multi-monitor display.

The default setting is the simultaneous display on

LCD and CRT with resolution of 1024 × 768.

When you press this button twice, the display mode returns to single display on LCD only.

Setting of multi-monitor display in Windows XP, computer changes its display mode to the multi-monitor display on LCD and CRT.

You can also return to single display by pressing this button twice.

The setting of TOSHIBA Presentation button can be changed through the properties of TOSHIBA

Controls. Display mode is changed to the multi-monitor display by selecting “Different

Image” (Windows XP only) or to the simultaneous display on internal and external display by selecting “Same Image”.

Press this button to launch the program automatically. When power-off, stand-by and hibernation, press this button to start the computer and launch the program.

You can select the function on TOSHIBA

Controls properties.

The default is TOSHIBA Assist.

2-8 User’s Manual

The Grand Tour

Power button Press the power button to turn the computer’s power on and off.

LCD Sensor switch This switch senses when the computer’s LCD display panel is closed or opened and activates the Panel Power Off/On feature. When you close the LCD display panel the computer enters

Hibernation mode and shuts down. When you open the computer's LCD display panel the computer starts in Hibernation mode. Use the

TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”.

Refer to the TOSHIBA Power Saver Utility and

Panel Power Off/On items in Chapter 1, Special features , for details on settings.

Do not put a magnetic object close to the switch. The computer will automatically enter Hibernation mode and shut down even if the Panel

Power Off features is disabled.

System indicators

LEDs beneath icons, light when various computer operations are in progress.

User’s Manual

SD card

DC IN

Power

System indicators

The SD card indicator glows green when the computer is accessing the SD card slot.

The DC IN indicator glows in green when DC power is supplied from the AC power adaptor.

If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.

The Power indicator glows in green when the computer is on. If you select Standby from Shut

Down Windows , this indicator blinking orange

(one second on, two seconds off) while the computer shuts down.

2-9

The Grand Tour

Battery

HDD

Wireless communication

The Battery indicator shows the condition of the battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to

Chapter 6, Power and Power-Up Modes .

The HDD indicator glows green when the computer is accessing the built-in hard disk.

The Wireless communication indicator glows when the wireless LAN function is turned on.

Some models are equipped with a Wireless communication.

Keyboard indicators

The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator.

When the Arrow mode indicator glows the keypad overlay lets you control the cursor.

When the Numeric mode indicator glows the keypad overlay lets you enter numbers.

When the Caps Lock indicator glows the keyboard is in all-caps mode.

Caps Lock

Caps Lock indicator

Caps Lock indicator

This indicator glows green when the alphabet keys are locked in uppercase.


The Grand Tour

Arrow mode indicator

Numeric mode indicator

Keypad overlay indicators

Arrow mode

Numeric mode

When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.

You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard.

USB floppy disk drive (optional)

The optional USB floppy disk drive accommodates 1.44-megabyte or

720-kilobyte floppy disks. It connects to a USB port.

USB connector

User’s Manual

Disk-In-Use

Indicator

Floppy disk slot

Eject button

USB floppy disk drive

USB connector Insert this connector to the USB port of your computer.

Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed.

2-11

The Grand Tour

Floppy disk slot

Eject button

Insert a floppy disk in this slot.

When a floppy disk is fully seated in the drive, the eject button pops out. To remove a floppy disk, push in the eject button and the floppy disk pops out partially for removal.

Check the Disk-In-Use indicator when you use the USB floppy disk drive.

Do not press the eject button or turn off the computer while the light is glowing. Doing so could destroy data and damage the floppy disk or the drive.

■ The USB floppy disk drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 o is operating.

while it

■ Do not set anything on top of the floppy disk drive.

Optical media drives

One of the following optical media drives is installed in the computer:

DVD-ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.

For information on loading and unloading discs refer to the Using optical media drives section in Chapter 4, Operating Basics.

Region codes for DVD drives and media

DVD-ROM&CD-R/RW, DVD Super Multi drives and media are manufactured according to the specifications of six marketing regions.

When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.

Code

1

2

3

4

5

6

Region

Canada, United States

Japan, Europe, South Africa, Middle East

Southeast Asia, East Asia

Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

Russia, Indian Subcontinent, Africa, North Korea, Mongolia

China


The Grand Tour

Writable discs

This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use

RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics .

CDs

■ CD-R discs can be written only once. The recorded data cannot be erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs, ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.

Formats

The drives support the following formats:

■ CD-ROM

■ DVD-ROM

■ CD-DA

■ Photo CD TM (single/multi-session)

■ CD-ROM XA Mode 2

(Form1, Form2)

■ DVD -Video

■ CD-Text

■ CD-ROM Mode 1, Mode 2

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

DVD-ROM&CD-R/RW drive

The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer edge.

DVD read

CD read

CD-R write

CD-RW write

8 speed (maximum)

24 speed (maximum)

24 speed (maximum)

24 speed (maximum, Ultra-speed media)


The Grand Tour

DVD Super Multi drive

The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer edge.

DVD read 8 speed (maximum)

DVD-R write

DVD-RW write

DVD+R write

DVD+RW write

2 speed (maximum)

2 speed (maximum)

2.4 speed (maximum)

2.4 speed (maximum)

DVD-RAM write 2 speed (maximum)

CD read 24 speed (maximum)

CD-R write

CD-RW write

24 speed (maximum)

10 speed (maximum, Ultra-speed media)

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from

100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. And the adaptor converts

AC power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes for details.

The AC adaptor (2-pin plug)


User’s Manual

The Grand Tour

The AC adaptor (3-pin plug)

■ The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled.

■ Do not use a 3-pin to 2-pin conversion plug.

The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.

For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.

Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.

2-15

The Grand Tour


PORTÉGÉ S100

Chapter 3

Getting Started

This chapter provides basic information to get you started using your computer. It covers the following topics:

■ Setting up your work space — for your health and safety

Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ Restoring the preinstalled software

All users should be sure to read the section Starting up for the first time .

Setting up your work space

Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation. This section discusses the following topics:

■ General conditions

■ Placement of the computer

■ Seating and posture

■ Lighting

■ Work habits


Getting Started

General conditions

In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment.

■ Make sure there is adequate space around the computer for proper ventilation.

■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

■ The temperature should be 5 to 35 degrees Centigrade

(41 to 95 degrees Fahrenheit) and the relative humidity should be

20 to 80 percent.

■ Avoid areas where rapid or extreme changes in temperature or humidity may occur.

■ Keep the computer free of dust, moisture, and exposure to direct sunlight.

■ Keep the computer away from heat sources, such as electric heaters.

■ Do not use the computer near liquids or corrosive chemicals.

■ Do not place the computer near objects that create strong magnetic fields (e.g., stereo speakers).

■ Some computers in the computer, including data storage media, can be damaged by magnets. Do not place the computer near magnetic objects or bring magnetic objects close to the computer. Be careful of objects, such as stereo speakers, that produce strong magnetic fields during operation. Also, be careful with metal objects, such as bracelets, which can be inadvertently magnetized.

■ Do not operate the computer in close proximity to a mobile phone.

■ Leave ample ventilation room for the fan. Do not block the vents.

Placement of the computer

Position the computer and peripheral devices to provide comfort and safety.

■ Set the computer on a flat surface at a comfortable height and distance.

The LCD display panel should be no higher than eye level to avoid eyestrain.

■ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices.

■ Allow adequate space behind the computer to let you freely adjust the

LCD display panel. The LCD display panel should be angled to reduce glare and maximize visibility.

■ If you use a paper holder, set it at about the same height and distance as the computer.

3-2 User’s Manual

Getting Started

Seating and posture

The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain.

Refer to the following tips.

Below eye level

90°angles

Foot rest

Posture and positioning of the computer

■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed.

■ Your knees should be slightly higher than your hips. If necessary, use a foot rest to raise the level of your knees to ease pressure on the back of your thighs.

■ Adjust the back of your chair so it supports the lower curve of your spine.

■ Sit straight so that your knees, hips and elbows form approximately

90 degree angles when you work. Do not slump forward or lean back too far.

Lighting

Proper lighting can improve legibility of the LCD screen and reduce eyestrain.

■ Position the computer so that sunlight or bright indoor lighting does not reflect off the LCD screen. Use tinted windows, shades or other screen to eliminate sun glare.

■ Avoid placing the computer in front of bright light that could shine directly in your eyes.

■ If possible, use soft, indirect lighting in your computer work area. Use a lamp to illuminate your documents or desk, but be sure to position the lamp so that it does not reflect off the LCD screen or shine in your eyes.

User’s Manual 3-3

Getting Started

Work habits

A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.

■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain.

■ Vary your posture frequently.

■ Occasionally stand up and stretch or exercise briefly.

■ Exercise and stretch your wrists and hands a number of times during the day.

■ Frequently, look away from the computer and focus your eyes on a distant object for several seconds, for example 30 seconds every

15 minutes.

■ Take frequent short breaks instead of one or two long breaks, for example, two or three minutes every half hour.

■ Have your eyes examined regularly and visit a doctor promptly, if you suspect you might be suffering from a repetitive strain injury.

A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome. For more information on these topics or for pointers on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer’s

Instruction Manual for Safety & Comfort.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.

The AC adaptor can be connected to any power source supplying from

100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes .

Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.

3-4 User’s Manual

Getting Started

■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical change and cause an electrical shock or minor bodily injury when touched.

As a general safety precaution, avoid touching any metal parts.

1. Connect the power cord to the AC adaptor.

Connecting the power cord to the AC adaptor (2-pin plug)

User’s Manual

Connecting the power cord to the AC adaptor (3-pin plug)

The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled.

3-5

Getting Started

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer.

DC IN 15V jack

Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.

Opening the display

The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing.

1. Push the display latch on the front of the computer to unlatch the display panel.

2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity.

Use reasonable care when opening and closing the LCD display panel.

Opening it vigorously or slamming it shut could damage the computer.

LCD display panel

Display latch

Opening the LCD display panel

3-6 User’s Manual

Getting Started

Turning on the power

This section describes how to turn on the power.

The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes.

■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time .

■ If the USB floppy disk drive is connected, make sure it is empty. If a floppy disk is in the drive, press the eject button and remove the floppy disk.

1. Open the computer’s LCD display panel.

2. Press and hold the computer’s power button for two or three seconds.

Turning on the power

Starting up for the first time

When you first turn on the power, the computer’s initial screen is the

Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.

Be sure to read the Windows End User License Agreement display carefully.

Be sure to read the License Agreement carefully.

User’s Manual 3-7

Getting Started

Turning off the power

The power can be turned off in one of the following modes:

Shut down (Boot), Hibernation or Standby mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.

1. If you have entered data, save it to the hard disk or to a floppy disk.

2. Make sure all disk (disc) activity has stopped, then remove the

CD/DVDs or floppy disk.

Make sure the HDD and Ultra Slim Bay’s module indicators are off.

If you turn off the power while a disk (disc) is being accessed, you can lose data or damage the disk (disc).

3. Click start then click Turn Off Computer . From the Turn Off

Computer menu select Turn Off .

4. Turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Hibernation mode

The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices.

■ Save your data. While entering hibernation mode, the computer saves the contents of memory to the HDD. However, for safety sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed. Wait for the HDD indicator to go out.

■ Do not install or remove a memory module while the computer is in hibernation mode. Data will be lost.

3-8 User’s Manual

User’s Manual

Getting Started

Benefits of hibernation

The hibernation feature provides the following benefits:

■ Saves data to the hard disk when the computer automatically shuts down because of a low battery.

For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and

Setup Action tab in TOSHIBA Power Saver.

Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.

■ You can return to your previous working environment immediately when you turn on the computer.

■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature.

■ You can use the panel power off feature.

Starting Hibernation

You can also enable Hibernation by pressing Fn + F4 . Refer to Chapter 5,

The Keyboard , for details.

To enter Hibernation mode, follow the steps below.

1. Click start .

2. Select Turn Off Computer .

3. Open the Turn Off Computer dialog box. Hibernate is not displayed.

4. Press the Shift key. The Standby item will change to Hibernate .

5. Select the Hibernate .

Automatic Hibernation

The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below.

1. Click start and open the Control Panel .

2. Open Performance and Maintenance and open Power Options .

3. Select the Hibernate window in the Power Options Properties , select the Enable hibernation check box and click the Apply button.

4. Open TOSHIBA Power Saver .

5. Select the Setup Action window.

6. Enable the desired Hibernation settings for When I press the power button and When I close the lid .

7. Click the OK button.

3-9

Getting Started

Data save in hibernation mode

When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD indicator will light.

After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Standby mode

If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory.

When you turn on the power again, you can continue working right where you left off.

■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility.

■ To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

■ If the computer automatically enters Standby mode while a network application is active, the application might not be restored when the computer wakes up from Standby.

■ To prevent the computer from automatically entering Standby mode, disable Standby in TOSHIBA Power Saver. That action, however, will nullify the computer’s Energy Star compliance.

■ Before entering Standby mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in standby mode. The computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in standby mode

(unless the computer is connected to an AC power source). Data in memory will be lost.

■ If you carry the computer on board an aircraft or into a hospital, be sure to shut down the computer in hibernation mode or in shutdown mode to avoid radio signal interference.

Benefits of standby

The standby feature provides the following benefits:

■ Restores the previous working environment more rapidly than does hibernation.

■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature.

■ You can use the panel power off feature.


Getting Started

Executing standby

You can also enable Standby by pressing Fn + F3 . See Chapter 5, The

Keyboard , for details.

You can enter standby mode in one of three ways:

1. Click start , click Turn Off Computer and click Stand By .

2. Close the computer’s LCD display panel. This feature must be enabled.

Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel.

Open Performance and Maintenance and open TOSHIBA Power

Saver.

3. Press the power button. This feature must be enabled. Refer to the

Setup Action tab in TOSHIBA Power Saver Utility described in the

Control Panel.

Open Performance and Maintenance and open TOSHIBA Power

Saver.

When you turn the power back on, you can continue where you left when you shut down the computer.

■ When the computer is shut down in standby mode, the power indicator blinking orange.

■ If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power.

Standby limitations

Standby will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Restarting the computer

Certain conditions require that you reset the system. For example, if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard commands.

■ There are three ways to reset the computer system:

1. Click start then click Turn off computer . From the Turn off computer menu select Restart .

2. Press Ctrl + Alt + Del to display the Windows Task Manager , then select Shut Down and Restart .

3. Press the power button and hold it down for five seconds. Wait 10 to

15 seconds, then turn the power on again by pressing the power button.


Getting Started

Restoring the preinstalled software

Restoring the complete system

To restore the operating system and all preinstalled software, follow the steps below.

When sound mute is turned ON by the Fn + Esc key, turn OFF before starting restore. Refer to Chapter 5, The Keyboard , for details.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Load the Product Recovery DVD-ROM in the optical media drive and turn off the computer’s power.

2. Hold down the F12 key and turn on the power. When In Touch with

Tomorrow TOSHIBA appears, release the F12 key.

3. Use the left or right cursor key to select the CD-ROM icon in the displayed menu. For details, refer to the Boot Priority section in Chapter

7, HW Setup.

4. Follow the on-screen instructions.

5. If your computer came with additional software installed, this software can not be recovered from the Product Recovery DVD-ROM. Re-install these applications (e.g. Works Suite, DVD Player, Games, etc.) separately from other media.

Restoring TOSHIBA utilities and drivers

If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.

Create a copy of this folder to an external media for more convenience.


PORTÉGÉ S100

Chapter 4

Operating Basics

This chapter gives information on basic operations including using the

Touch Pad, USB floppy disk drive (optional), changing Ultra Slim Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on caring for your computer, floppy disks and CD/DVDs.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.

Touch Pad

User’s Manual

Touch Pad control buttons

Touch Pad and Touch Pad control buttons

Two buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.

You can also tap the Touch Pad to perform functions similar to those of the left button.

Click: Tap once

Double-click: Tap twice

Drag and drop: Tap to select the material you want to move.

Leave your finger on the Touch Pad after the second tap and move the material.

4-1

Operating Basics

Using the USB floppy disk drive (optional)

USB floppy disk drive connects to the computer’s USB port.

It accommodates 1.44-megabyte or 720-kilobyte floppy disks.

Refer to Chapter 2, The Grand Tour , for more information.

Option or provided with some models.

Connecting USB floppy disk drive

To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port.

Make sure the connector is back side up and properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.

USB port

USB connector

4-2

Connecting the USB floppy disk drive

If you connect the USB floppy disk drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive.

Do not disconnect and reconnect before 10 seconds has elapsed.

Disconnecting USB floppy disk drive

When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it:

1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped.

If you disconnect the USB floppy disk drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy disk or the drive.

2. Click the Safely Remove Hardware icon on the Task Bar.

3. Click USB floppy disk drive that you want remove.

4. Pull the floppy disk drive’s USB connector out of the computer’s USB port.

User’s Manual

Operating Basics

Changing Ultra Slim Bay modules

This section explains how to change modules in the Ultra Slim Bay.

The illustrations show replacement of the optical media drive with the

Ultra Slim Bay HDD adaptor. Therefore, the text refers to those modules.

However, the procedures are the same for any of the modules:

DVD-ROM&CD-R/RW drive, DVD Super Multi drive, HDD adaptor and

Ultra Slim Bay weight saver.

To avoid injury, do not put your hand into the Ultra Slim Bay slot.

The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction , for information on using this utility to change modules while the computer’s power is on.

Removing a module

Remove the optical media drive as described below.

1. You can confirm that the disks are not operating with indicators.

If all indicators are off, it means that no disks are operating currently.

2. Turn the computer upside down.

Wait for all disk indicators to go out before you turn over the computer and do not lay the computer down gently. Shock can damage the HDD or other components.

3. Remove the screw near the icon securing the Ultra Slim Bay.

4. Make sure the screw in the Ultra Slim Bay lock is set in the hole for the unlock position.

5. Slide the Ultra Slim Bay latch to the unlock position.

User’s Manual 4-3

Operating Basics

6. Grasp the optical media drive and slide it out.

■ The optical media drive and other Ultra Slim Bay modules can become hot with use. Be careful when removing the module.

■ Store the DVD Super Multi drive unit in the Ultra Slim Bay Case when removing it from the computer or transporting it.

Lock screw

Ultra Slim

Bay latch

Optical media drive

Removing the optical media drive

Inserting a module

Insert the Ultra Slim Bay HDD adaptor as described below.

1. Insert the Ultra Slim Bay HDD adaptor in the computer as shown below and press until the ejector clicks.

2. If you want to lock the Ultra Slim Bay HDD adaptor, set the Ultra Slim

Bay lock screw in the hole for the lock position ( ➁ ). The lock screw is inserted in the unlock position ( ➀ ) at the time of purchasing.

Lock screw

4-4

Ultra Slim Bay

HDD adaptor

Inserting the Ultra Slim Bay HDD adaptor

User’s Manual

Operating Basics

Using optical media drives

The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. You can run either 12 cm (4.72") or 8 cm (3.15")

CD/DVDs without an adaptor. An ATAPI interface controller is used for

CD/DVD-ROM operation. When the computer is accessing a

CD/DVD-ROM, an indicator on the drive glows and the Ultra Slim Bay indicator glows.

Use the WinDVD application to view DVD-Video discs.

If you have a DVD-ROM&CD-R/RW drive, refer also to the Writing CDs on

DVD-ROM&CD-R/RW drive section for precautions on writing to CDs.

If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on

DVD Super Multi drive section for precautions on writing to CDs.

When the power of the optical media drive is off, pressing the Fn + Tab keys will turn the power of the optical media drive on. Furthermore, it is possible to set it to turn the power of the optical media drive on and eject the tray at the same time.

Loading discs

To load CD/DVDs, follow the steps below.

1. When the computer’s power is on, press the eject button to open the disc tray slightly.

Eject Button

Pressing the eject button

User’s Manual 4-5

Operating Basics

2. Grasp the disc tray gently and pull until it is fully opened.

Pulling the disc tray open

3. Lay the CD/DVD, label side up, in the disc tray.

Disc tray

4-6

Laser lens

Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat.

■ Do not touch a laser lens and its circumference portion. Doing so could cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive.

4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base.

User’s Manual

Operating Basics

5. Push the center of the disc tray to close it. Press gently until it locks into place.

If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.

Closing the CD/DVD disc tray

Removing discs

To remove the CD/DVD, follow the steps below.

Do not press the eject button while the computer is accessing the media drive. Wait for the Ultra Slim Bay indicator to go out before you open the disc tray. Also, if the CD/DVD is spinning when you open the disc tray, wait for it to stop before you remove it .

1. To pop the disc tray partially open, press the eject button. Gently pull the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the

CD/DVD has stopped spinning before pulling the disc tray fully open.

2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out.

User’s Manual

Removing a CD/DVD

3. Push the center of the disc tray to close it. Press gently until it locks into place.

4-7

Operating Basics

How to remove CD/DVD when the disk tray will not open

Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.

Eject hole

Manual release with the eject hole

Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the disc tray, the CD/DVD could fly off the spindle and cause injury.

Writing CDs on DVD-ROM&CD-R/RW drive

Depending on the type of drive installed, you may be able to write CDs.

The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs.

Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the

Using optical media drives section.

■ CD-R discs can be written to only once. CD-RW discs can be rewritten many times.

■ When the power of the optical media drive is off, the disc tray will not open even if the eject button is pushed. Use the optical media drive power icon to turn the power of the optical media drive on. Refer to

Chapter 1, Special features .

■ Do not turn off the power of the optical media drive while the computer is accessing the drive. If you turn off the power, you may lose data.

4-8 User’s Manual

Operating Basics

Before writing or rewriting

Please observe the following points when you write or rewrite the data.

■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates.

CD-R:

TAIYO YUDEN CO., LTD.

MITSUBISHI CHEMICAL CORPORATION

RICOH Co., Ltd.

Hitachi Maxell Ltd.

Multi-Speed and High-Speed CD-RW:


RICOH Co., Ltd.

Ultra-Speed CD-RW:


TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed.

■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.

■ Be sure to connect the AC adaptor when you write or rewrite.

■ Be sure to close all other software programs except the writing software.

■ Do not run software such as a screen saver which can put a heavy load on the CPU.

■ Operate the computer at full power. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and damage data.

■ Write from the computer's HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device.

■ Writing with software other than Sonic RecordNow! has not been confirmed. Therefore, operation with other software cannot be guaranteed.

User’s Manual 4-9

Operating Basics

When writing or rewriting

Note the following when you write or rewrite a CD-R or CD-RW.

■ Always copy data from the HDD to the CD. Do not use cut-and-paste.

The original data will be lost if there is a write error.

■ Do not perform any of the following actions:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, USB devices, external monitor, i.LINK devices, optical digital devices.

■ Open the optical media drive.

■ Remove the optical media drive from the Ultra Slim Bay.

■ If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur.

■ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand.

■ Keep mobile phones and other wireless communication devices away from the computer.

Writing CD/DVDs on DVD Super Multi drive

You can use the DVD Super Multi drive to write data to either CD-R/RW or

DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: RecordNow!, and DLA licensed by Sonic Solutions.

■ CD-R discs can be written to only once. CD-RW discs can be rewritten many times.

■ When the power of the optical media drive is off, the disc tray will not open even if the eject button is pushed. Use the optical media drive power icon to turn the power of the optical media drive on. Refer to

Chapter 1, Special features .

■ Do not turn off the power of the optical media drive while the computer is accessing the drive. If you turn off the power, you may lose data.

Important message

Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc, read and follow all setup and operating instructions in this section.

If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.


Operating Basics

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/RW or

DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.

■ Damage that may be caused by using third party equipment or software.

Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents.

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.

CD-R:



RICOH Co., Ltd.

Hitachi Maxell Ltd.

CD-RW: (Multi-Speed and High-Speed)


RICOH Co., Ltd.

CD-RW: (Ultra-Speed)


DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0


Matsushita Electric Industrial Co., Ltd.

DVD+R:


RICOH Co., Ltd.


Operating Basics

4-12

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or version 1.2

VICTOR COMPANY OF JAPAN.LIMITED


DVD+RW:


RICOH Co., Ltd.

DVD-RAM:

DVD Specifications for DVD-RAM Disc for Version 2.0 or

Version 2.1

Matsushita Electric Industrial Co., Ltd.

Hitachi Maxell Ltd.

This drive cannot use discs that allow writing faster than 8 speed

(DVD-R,DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM).

■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or

DVD-RAM is affected by the quality of the disc and the way it is used.

■ There are two types of DVD-R discs: authoring and general use discs.

Do not use authoring discs. Only general use discs can be written to by a computer drive.

■ You can use DVD-RAM discs that can be removed from a cartridge and

DVD-RAM discs designed without a cartridge. You cannot use a disc with a 4.7 GB single-sided capacity or 9.4 GB double-sided capacity.

■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW or DVD+R/+RW discs.

■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in whole or in part.

■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and

DVD-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.

■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc.

■ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data.

■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without DVD-RAM Driver Software.

User’s Manual

Operating Basics

■ When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive.

■ Be sure to connect the AC adaptor before you write or rewrite.

■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media.

■ Be sure to close all other software programs except the writing software.

■ Do not run software such as a screen saver, which can put a heavy load on the CPU.

■ Operate the computer in the full-power mode. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and data damage.

■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost or damaged.

■ Write from the computer’s HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device.

■ Writing with software other than RecordNow! and InterVideo WinDVD

Creator Platinum are not recommended.

When writing or rewriting

Please observe/consider the following when you write or rewrite to a

CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, USB devices, external monitor, i.LINK devices, optical digital devices.

■ Use the Audio/Video control button to reproduce music or voice.

■ Open the optical media drive.

■ Remove the optical media drive from the Ultra Slim Bay.

■ Do not use shut down/log off and standby/hibernation while writing or rewriting.

■ Make sure writing or rewriting is completed before going into standby/hibernation. Writing is completed if you can open the

DVD-ROM&CD-R/RW or DVD Super Multi drive tray.


Operating Basics

■ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand.

■ Keep mobile phones and other wireless communication devices away from the computer.

■ Always copy data from the HDD to the DVD-RAM. Do not use cut-and-paste. The original data will be lost if there is a write error.

RecordNow! Basic for TOSHIBA

Note the following limitations when you use RecordNow!:

■ DVD-Video cannot be created using RecordNow!.

■ DVD-Audio cannot be created using RecordNow!.

■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-RW or DVD+R/+RW disc.

■ Do not use the “Exact Copy” function of RecordNow! to copy

DVD-Video and DVD-ROM with copyright protection.

■ DVD-RAM disc cannot be backed up with the “Exact Copy” function of

RecordNow!.

■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or

DVD+R/+RW using the “Exact Copy” function of RecordNow!.

■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or

DVD+R/+RW to CD-R/RW using the “Exact Copy” function of

RecordNow!.

■ RecordNow! cannot record in packet format.

■ You might not be able to use the “Exact Copy” function of RecordNow! to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder.

■ If you add data to a DVD-R and DVD+R disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as

Windows 98SE and Windows Me. In Windows NT4, you will need

Service Pack 6 or later to read added data. In Windows 2000, you will need Service Pack 2 or later to read it. Some DVD-ROM and

DVD-ROM&CD-R/RW drives cannot read added data regardless of the operating system.

■ RecordNow! does not support recording to DVD-RAM discs.

To record to a DVD-RAM, use Explorer or other utility.

■ When you back up a DVD disc, be sure the source drive supports recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive does not support recording to DVD-R/-RW or DVD+R/+RW discs, it might not be backed up correctly.

■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to use the same type of disc.

■ You cannot partially delete any data written to a CD-RW, DVD-RW or

DVD+RW disc.


Operating Basics

Data Verification

To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD.

1. Click the Options button (

Options panels.

) on the RecordNow! Console to open the

2. Select the Data in the left-side menu.

3. Mark the Verify data written to the disc after burning check box in the

Data Options.

Click the OK button.

DLA for TOSHIBA

Note the following limitations when you use DLA:

■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable.

■ DLA does not support formatting a DVD-RAM disc and writing to it.

They are performed by DVD-RAM Driver Software. If DLA Format menu may appear when inserting a DVD-RAM disc into the drive and right-clicking the drive icon in Windows Explorer, please use

“DVDForm” to format this disc. You can run “DVDForm” by clicking the

Start button on the taskbar to display the Start menu and then selecting

“All Programs”, “DVD-RAM”, “DVD-RAM Driver” and “DVDForm” sequentially.

■ Do not use any discs that have been formatted with packet writing software other than DLA. Similarly, do not use any discs that have been formatted with DLA with any packet writing software other than DLA.

When using a disc you are not familiar with, format it by selecting

“Full Format” before using it.

■ Do not use the Cut & Paste function for files and folders. A file or folder that has been cut may be lost if writing fails due to an error on the disc.

■ When writing the Setup files for the program to a disc formatted by DLA and starting Setup from this disc, an error may occur. In this case, please copy them to your hard disk and then run Setup.

Video

As for InterVideo WinDVD Creator Platinum. Only the model that can be written in to DVD is attached.


Operating Basics

When using WinDVD Creator Platinum

You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy.

1. Click start and select the Control Panel .

2. Click the Performance and Maintenance icon in the Control Panel.

3. Click the System icon in the Performance and Maintenance window.

4. Click the Advanced tab in the System Properties window.

5. Click the Settings icon in the “Performance” section.

6. Click the Advanced tab in the Performance Options window.

7. Click the Change icon in the “virtual memory” section.

8. Select the Custom size button in the Virtual Memory window.

9. Specify much higher values for “Initial size” and “Maximum size.”

10. Click the Set button in the Virtual Memory window.

11. Click the OK button in the Virtual Memory window.

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a

DV-Camcorder:

1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] -

[InterVideo WinDVD Creator] to launch WinDVD Creator.

2. Click [Capture] button then capture the video data from the

DV-Camcorder via IEEE1394.

3. Click [Edit] button then drag the video clips from [Video Library] tab to the edit track.

4. Click [Make Movie] button in the top bar.

5. Double Click the Right arrow button icon in the center of right side.

6. Put a blank DVD-R/+R disc or an erased DVD-RW/+RW disc in the drive.

7. Click [Start] to record to the disc.

8. When recording is finished, the tray opens.

How to learn more about InterVideo WinDVD Creator

Please refer to the on-line Help for additional InterVideo WinDVD Creator information.


Operating Basics

Important information for use

Note the following limitations when you write video DVD:

1. Editing digital video

■ Log in with Administrator rights to use WinDVD Creator.

■ Make sure that your computer is running on AC power when using

WinDVD Creator.

■ Operate the computer at Full Power. Do not use power-saving features.

■ While you are editing DVD, you can display previews. However, if another application is running, the preview might not display properly.

■ WinDVD Creator cannot show video on the external monitor when in simultaneous mode.

■ WinDVD Creator cannot edit or play copy protected content.

■ Do not change display settings while using WinDVD Creator.

■ Do not enter standby/hibernation mode while using WinDVD

Creator.

■ Do not operate WinDVD Creator immediately after turning on the computer. Please wait until all Disc Drive activity has stopped.

■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data.

■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD functions are not supported in this version.

■ While recording video to DVD or tape, please close all other programs.

■ Do not run software like a screen saver because it can put a heavy load on the CPU.

■ Do not run communication applications like a modem or a LAN.

2. Before recording the video to DVD

■ When you record to DVD disc, please use only discs recommended by the Drive manufacturer.

■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD.

■ Do not perform any of the following actions:

■ Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel.

■ Bump or cause vibration to the computer.

■ Use the Mode control button and Audio/Video control button to reproduce music or voice.

■ Open the DVD drive.

■ Install, remove or connect external devices, including the following: PC card, SD card, USB devices, external monitor, i.LINK devices, optical digital devices.


Operating Basics

■ Please verify your disc after recording important data.

■ DVD-R/+R/-RW disc cannot be written in VR format.

■ WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD format.

■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the disc may only play on your computer.

■ When writing to DVD disc, WinDVD Creator requires 2GB or more over disk space every one hour of video.

■ When you make a fully recorded DVD, the chapter sequence may not play correctly.

3. About Disc Manager

■ WinDVD Creator can edit one play list on a disc.

■ WinDVD Creator might show a different a thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder.

■ Using the Disc Manager, you can edit DVD-VR format on

DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW.

4. About recorded DVDs

■ Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.

■ When playing your recorded disc on your computer, please use the

WinDVD software application.

■ If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc.

Media care

This section provides tips on protecting data stored on your CD/DVDs and floppy disks.

Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them:

CD/DVDs

1. Store your CD/DVDs in the container they came in to protect them and keep them clean.

2. Do not bend the CD/DVD.

3. Do not write on, apply a sticker to, or otherwise mar the surface of the

CD/DVD that contains data.

4. Hold the CD/DVD by its outside edge or the edge on the center hole.

Fingerprints on the surface can prevent the drive from properly reading data.

5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs.


Operating Basics

6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner.

Floppy disks

1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid.

Clean it with a soft damp cloth.

2. Do not slide back the floppy disk’s protective metal covering or touch the floppy disk’s magnetic surface. Fingerprints may prevent the floppy disk drive from reading data from the floppy disk.

3. Data may be lost if the floppy disk is twisted; bent; or exposed to direct sunlight, extreme heat or cold.

4. Do not place heavy objects on your floppy disks.

5. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface.

6. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields.

Sound System

Using the microphone

Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions.

Since your computer has a built-in microphone and speaker, “howling” may be heard under certain conditions. Howling occurs when sound from the speaker is picked up in the microphone and amplified back to the speaker, which amplifies it again to the microphone.

This howling occurs repeatedly and causes a very loud, high-pitched noise.

It is a common phenomenon that occurs in any sound system when the microphone input is output to the speaker (throughput) and the speaker volume is too loud or too close to the microphone. You can control throughput by adjusting the volume of your speaker or through the Mute function.

To adjust the volume or activate Mute, click start , point to All Programs , point to Accessories , point to Entertainment and click Volume Control .

In the Volume Control panel, you can use the slide bars to adjust the volume level or click Mute at the bottom of the panel.


Operating Basics

SoundMAX control panel

The SoundMAX control panel lets you control additional functions for the

Microphone Enhancement and Audio Power Management. To launch the

SoundMAX Control Panel, follow the steps below.

1. Click start and click Control Panel.

2. If you are viewing the Control Panel in Category View, click on Switch to Classic View .

3. Double-click the SoundMAX icon.

The Microphone Setup allows you to optimize the microphone input settings for your particular configuration. Choose Standard Microphone if you have an ordinary desktop microphone. Choose Headset if you have a wearable microphone that is positioned directly in front of your mouth.

You can launch the Setup Wizard from the Control Panel to help you to automatically set proper microphone input volumes and ensure that your voice input(s) are working correctly. As you speak into the microphone, the Sound Meter indicates the audio signal that your PC is receiving.

The Noise Reduction enhancement helps to eliminate ambient noise from the voice input signal to provide a clean and clear signal to applications.

This feature can be used with any microphone.

The audio controller can be powered down when the audio function is idle.

To enable the Audio Power Management, follow the steps below.

1. Click the Power Management tab.

2. Select the Normal Power Savings in the Power Mode pull-down list.

If the No Power Savings is selected, the audio controller always runs.

If you want to a more effect for the power management, you can select another mode, the High Power Savings which can save the power than the Normal Power Savings. To select it, follow the steps below.

1. Click the Power Management tab.

2. Select the High Power Savings in the Power Mode pull-down list.

3. Input a time in Power Save Delay (Seconds) .

If the High Power Saving is selected, you need to play an audio file once before you use a microphone or play an audio CD by the analog CD audio.

Mic Effect

TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area

Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone.

TOSHIBA Mic Effect will reduce these echoes generated on your computer.

Form more information on using the TOSHIBA Mic Effect, refer to its help.


Operating Basics

Modem

This section describes how to connect and disconnect the internal modem to and from a telephone jack.

The internal modem does not support voice functions. All data and fax functions are supported.


■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.

Region selection

Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used.

To select a region, follow the steps below.

1. Click start , point to All Programs , point to TOSHIBA , point to

Networking and click Modem Region Select .

Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the

Country/Region in the Control Panel, the change may not take effect.

2. The Region Selection icon will appear in the Windows Task Bar.

3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.

4. Select a region from the region menu or a telephony location from the sub-menu.

■ When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically.

■ When you select a telephony location, the corresponding region is automatically selected and it becomes the modem’s current region setting.

Properties menu

Click the icon with the secondary mouse button to display properties menu on the screen.


Operating Basics

Setting

You can enable or disable the following settings:

AutoRun Mode

The Region Select utility starts automatically when you start up the operating system.

Open the Dialing Properties dialog box after selecting region.

The dialing properties dialog box will be displayed automatically after you select the region.

Location list for region selection.

A submenu appears displaying location information for telephony.

Open dialog box, if the modem and Telephony Current

Location region code do not match.

A warning dialog box is displayed if current settings for region code and telephony location are incorrect.

Modem Selection

If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use.

Dialing Properties

Select this item to display the dialing properties.

If you are using the computer in Japan, the Telecommunications Business

Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.

Connecting

To connect the modular cable, follow the steps below.

The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer.


■ Do not connect the modem to a digital telephone line.

A digital line will damage the modem.


Operating Basics

1. Plug one end of the modular cable into the computer’s modem jack.

2. Plug the other end of the modular cable into a telephone jack.

Modular cable

Telephone jack

Connecting the internal modem

Do not pull on the cable or move the computer while the cable is connected.

If you use a storage device such as an optical drive or HDD connected to a

16-bit PC card, you might experience the following modem problems:

■ Modem speed is slow or communication is interrupted.

■ Skips may occur in sound.

Disconnecting

To disconnect the internal modular cable, follow the steps below.

1. Pinch the lever on the connector in the telephone jack and pull out the connector.

2. Disconnect the cable from the computer’s modem jack in the same manner.

Wireless communications

The computer’s wireless communication function supports Wireless LAN.

Wireless LAN

The Wireless LAN is compatible with other LAN systems based on Direct

Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard

(Revision A, B or G).

■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g)

■ Theoretical maximum speed: 11Mbps (IEEE802.11b)

■ Frequency Channel Selection (Revision A:5 GHz, Revision B/G:

2.4 GHz)

■ Roaming over multiple channels

■ Card Power Management


Operating Basics

■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit encryption algorithm (Intel module type).

■ Wi-Fi Protected Access (WPA).

■ The numerical values for display are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.

The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard. The actual transmission speed will be lower than the theoretical maximum speed.

Security

■ Be sure to enable WEP (encryption) function. Otherwise your computer will allow the illegal access by outsider through Wireless LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data.

TOSHIBA strongly recommend the customer to enable the WEP function.

■ TOSHIBA is not liable for the eavesdropping of data due to the use of

Wireless LAN and the damage thereof.

Wireless communication switch

You can enable or disable Wireless LAN function, with the on/off switch.

No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off.

■ Set the switch to off in airplanes and hospitals. Check the indicator.

It will stop glowing when the wireless communication function is off.

■ Turn the computer off when you enter an airplane and check the carrier's regulations before you use a computer on board.


Operating Basics

LAN

Wireless communication Indicator

The wireless communication indicator indicates the status of the wireless communication functions.

Indicator status

Indicator off

Indication

Wireless communication switch is set to off.

Automatic power down because of overheating.

Power malfunction

Indicator glows Wireless communication switch is on. Wireless

LAN is turned on by an application.

If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN. Open or click the following: Start , Control Panel , System , Hardware Device

Manager , Network adapters , Intel ® PRO/Wireless 2200BG/2915ABG

Network Connection and enable.

The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second,

100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second,

1000BASE-T).

This section describes how to connect/disconnect to a LAN.

Do not install or remove an optional memory module while Wake-up on

LAN is enabled.

The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.

LAN cable types

The computer must be configured properly before connecting to a LAN.

Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.

If you are using Gigabit Ethernet LAN (1000 megabits per second,

1000BASE-T), be sure to connect with a CAT5E cable or higher.

You cannot use a CAT3 or CAT5 cable.

If you are using Fast Ethernet LAN (100 megabits per second,

100BASE-TX), be sure to connect with a CAT5 cable or higher.

You cannot use a CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher.


Operating Basics

Connecting LAN cable

To connect the LAN cable, follow the steps below.

■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the

AC Adaptor while the computer is accessing a LAN, the system may hang up.

■ Do not connect any other cable to the LAN jack except the LAN cable.

Otherwise, malfunctions or damage may occur.

■ Do not connect any power supplying device to the LAN cable that is connected to the LAN jack. Otherwise, malfunctions or damage may occur.

1. Turn off the power to the computer and to all external devices connected to the computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.

LAN connector

4-26

LAN jack

Connecting the LAN cable

3. Plug the other end of the cable into a LAN hub connector.

Check with your LAN administrator before connecting to a hub.

When the computer is exchanging data with the LAN, the LAN Active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green.

Disconnecting LAN cable

To disconnect the LAN cable, follow the steps below.

Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN.

1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector.

2. Disconnect the cable from the LAN hub in the same manner.

Check with your LAN administrator before disconnecting from the hub.

User’s Manual

Operating Basics

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer.

■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen. Spray a small amount of cleaner on a soft, clean cloth and wipe the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.

Moving the computer

The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation.

■ Before moving the computer, it recommends changing the function of

HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD)

Protection , in this chapter.

■ Make sure all disk activity has ended before moving the computer.

Check the HDD indicator on the computer.

■ If a CD/DVD is in the drives, remove it. Also make sure the disc tray is securely closed.

■ Turn off the power to the computer.

■ Disconnect the AC adaptor and all peripherals before moving the computer.

■ Close the LCD display panel. Do not pick up the computer by its panel.

■ Close all port covers.

■ Use the carrying case when transporting the computer.

■ When carrying your computer, be sure to hold it securely so that it does not fall or hit anything.

■ Do not carry your computer by holding protruded portions.


Operating Basics

Using the Hard Disk Drive (HDD) Protection

There is a function for reducing the risk of damage on HDD in this computer.

Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact.

This function does not guarantee that the HDD will not be damaged.

When vibration is detected, the following message is displayed, and the icon in the notification area of the taskbar is changed to the protection state. This message is displayed until the OK button is pressed or

30 seconds pass. When vibration subsides, the icon returns to the normal state.

HDD Protection Message

Taskbar Icon

State

Normal

Icon Description

HDD Protection is enabled.

Protection

OFF

HDD Protection is active.

The HDD head is at a safe position.

HDD Protection is disabled.


Operating Basics

TOSHIBA HDD Protection Properties

You can make the HDD Protection settings by using the TOSHIBA HDD

Protection Properties window. To open the window, click start point to All

Programs point to TOSHIBA point to Utilities and click HDD Protection setting . The window can also be started from the icon on the Taskbar, or from the Control Panel.

User’s Manual

TOSHIBA HDD Protection Properties

HDD Protection

You can choose whether to enable or disable HDD Protection.

Detection Level

This function can be set to four levels. The sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF,

1, 2, and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used as handheld or in other unstable conditions, setting the detection level to 3 could result in frequent execution of HDD Protection, which will slow HDD reading and writing. Set a lower detection level when the speed of HDD reading and writing is a priority.

Different detection levels can be set depending on whether the computer is used as handheld or mobile usages, or whether it is used in a stable environment such as on a table in the workplace or at home. By setting different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode.

4-29

Operating Basics

Detail Properties

To open the Detail Properties window, click the Setup Detail button in the

TOSHIBA HDD Protection Properties window.

Detail Properties

Detection Level Amplification

When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.

HDD Protection Message

Specify whether to display a message when HDD Protection is active.

■ This function does not work when the computer is starting, in standby, in hibernation, in transition to hibernation, recovering from hibernation, or powered off. Be sure to not subject the computer to vibration or impact while the function is disabled.

■ This function supports only Windows ® XP.


Operating Basics

Heat dispersal

To protect from overheating, the CPU has an internal temperature sensor.

If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the

Basic Setup tab in TOSHIBA Power Saver.

Maximum

Performance

Turns on the fan first, then if necessary, lowers the CPU processing speed.

Performance Uses a combination of the fan and lowering the CPU processing speed.

Battery optimized

Lowers the CPU processing speed first, then if necessary turns on the fan.

When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.

If the CPU temperature reaches an unacceptably high level with either setting, the system automatically shuts down to prevent damage.

Data in memory will be lost.


Operating Basics


PORTÉGÉ S100

Chapter 5

The Keyboard

The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the

101/102-key keyboard functions can be executed on the computer.

The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.

There are six types of keys: typewriter keys, function keys, soft keys,

Hot keys, Windows special keys and keypad overlay.

Typewriter keys

The typewriter keys produce the upper- and lower-case letters, numbers, punctuation marks, and special symbols that appear on the screen.

There are some differences, however, between using a typewriter and using a computer keyboard:

■ Letters and numbers produced in computer text vary in width. Spaces, which are created by a “space character,” may also vary depending on line justification and other factors.

■ The lowercase l (el) and the number 1 (one) are not interchangeable on computers as they are on a typewriter.

■ The uppercase O (oh) and the 0 (zero) are not interchangeable.

■ The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position.

■ The Shift keys, the Tab key, and the BkSp (backspace) key perform the same function as their typewriter counterparts but also have special computer functions.


The Keyboard

Function keys: F1 … F12

The function keys (not to be confused with Fn ) are the 12 keys at the top of your keyboard. These keys function differently from other keys.

F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer.

Refer to the section, Soft keys: Fn key combinations , in this chapter.

The function executed by individual keys depends on the software you are using.

Soft keys: Fn key combinations

The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

Some software may disable or interfere with soft-key operations.

Soft-key settings are not restored by the Standby feature.

Emulating keys on enhanced keyboard

Esc F1

F2

F3 F4 F5 F6 F7 F8 F9 F10 F11 F12

PrtSc

SysReq

Scroll

lock

Pause

Break

~

`

Tab

!

1

@

2

#

3

$

4

%

5

^

6

&

7

*

8

(

9

)

0

_

-

CapsLock

Ctrl

Shift

Q

A

Z

W

S

Alt

X

E

D

C

R

F

V

T

G

Y

B

H

U

N

J

I

M

K

O

<

,

P

L

>

.

:

;

Alt

?

/

[

{

,

,,

+

=

]

}

Enter

Bk Sp

Shift

Ctrl

\

Ins

Home

PgUp

Del End PgDn

Num

Lock

7

Home

4

/

8

5

2

9

PgUp

6

+

1

End

0

Ins

3

PgDn

.

Del

Enter

101-key enhanced keyboard layout

The keyboard is designed to provide all the features of the 101-key enhanced keyboard. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.

Your software may require you to use keys that the keyboard does not have. Pressing the Fn key and one of the following keys simulates the enhanced keyboard’s functions.

5-2 User’s Manual

The Keyboard

Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys ( Fn + F11 ) or cursor control keys ( Fn + F10 ). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off.

Press Fn + F12 ( ScrLock ) to lock the cursor on a specific line. The power on default is off.

Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad.

Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.

Hot keys

Hot keys ( Fn + a function or Esc key) let you enable or disable certain features of the computers.

User’s Manual

Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon.

5-3

The Keyboard

Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK .

If no password is set, the screen will be restored when you press any key or press the Touch Pad.

Power save mode: Pressing Fn + F2 changes the power save mode.

If you press Fn + F2 in a Windows environment, the settings dialog box for the Power Save Mode, similar to the one below, is displayed. Continue holding down Fn , and release and press F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power

Saver.

Standby : When you press Fn + F3 , the computer enters the Standby mode. Before entering Standby, a dialog box appears asking for your confirmation. This dialog box will not be displayed in the future when you click the check box in it.

Hibernation : When you press Fn + F4 , the computer enters the

Hibernation mode. Before entering Hibernation, a dialog box appears asking for your confirmation. This dialog box will not be displayed in the future when you click the check box in it.

5-4 User’s Manual

The Keyboard

Display selection: Press Fn + F5 to change the active display device.

When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5 , the selected device will change.

If you hold down these hot keys for five seconds the selection will return to the internal LCD .

Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements. When you press these hot keys, the current setting will be displayed for two seconds by an icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver.

Internal LCD screen Brightness: Pressing Fn + F7 increases the LCD screen brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Screen brightness item of the Basic

Setup tab in TOSHIBA Power Saver.

■ The brightness level is always set at the maximum value for about

18 seconds, when the internal LCD screen turns on. After 18 seconds, the brightness level will appear at the Power Save Mode setting or you can change it manually.

■ LCD screen clarity increases with the brightness level.

Wireless setting: Fn + F8 are not used.

User’s Manual

Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the Touch Pad function. When you press these hot keys, the current setting will change and be displayed as an icon.

5-5

The Keyboard

LCD screen resolution selection: Press Fn + Space keys to change the display resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: The available resolution depends on the model. With XGA, you can change the resolution between

800 × 600 and 1024 × 768 pixels. With SXGA, between 800 × 600 and

1400 × 1050 pixels.

Optical media drive power icon: Press the Fn + Tab keys to turn the power of the optical media drive on or eject the disc tray. A dialog box is displayed when this hotkey is pressed. To choose between the functions, press the Tab key while holding down the Fn key. The chosen function is executed when the Fn + Tab keys are released.

TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down the

Fn key.

TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the

Fn key.

Fn Sticky key

You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “ F number ” key.

To start the TOSHIBA Accessibility Utility, click start , point to All

Programs , point to TOSHIBA, point to Utilities and click Accessibility .

5-6 User’s Manual

The Keyboard

Windows special keys

The keyboard provides two keys that have special functions in Windows:

Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button.

This key activates the Windows start menu.

This key has the same function as the secondary mouse button.

Keypad overlay

Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.

The keys in the center of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in the figure below.

Turning on the overlays

The numeric keypad overlay can be used for numeric data input or cursor and page control.

Arrow mode

To turn on the Arrow mode, press Fn + F10 . The Arrow mode indicator lights. Now try cursor and page control using the keys shown in the figure below. Press Fn + F10 again to turn off the overlay.

User’s Manual 5-7

The Keyboard

Numeric mode

To turn on the Numeric mode, press Fn + F11 . The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below.

Press Fn + F11 again to turn off the overlay.

5-8

The numeric keypad overlay

Temporarily using normal keyboard (overlay on)

While using the overlay, you can temporarily access the normal keyboard without turning off the overlay:

1. Hold Fn and press any other key. All keys will operate as if the overlay were off.

2. Type upper-case characters by holding Fn + Shift and pressing a character key.

3. Release Fn to continue using the overlay.

Temporarily using overlay (overlay off)

While using the normal keyboard, you can temporarily use the keypad overlay without turning it on:

1. Press and hold down Fn .

2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control.

3. Release Fn to return to normal keyboard operation.

User’s Manual

The Keyboard

Temporarily changing modes

If the computer is in Numeric mode , you can switch temporarily to Arrow mode by pressing a shift key.

If the computer is in Arrow mode , you can switch temporarily to Numeric mode by pressing a shift key.

Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes.

With the overlay on:

1. Hold down Alt .

2. Using the overlay keys, type the ASCII code.

3. Release Alt , and the ASCII character appears on the display screen.

With the overlay off:

1. Hold down Alt + Fn .

2. Using the overlay keys, type the ASCII code.

3. Release Alt + Fn , and the ASCII character appears on the display screen.

User’s Manual 5-9

The Keyboard


PORTÉGÉ S100

Chapter 6

Power and Power-Up Modes

The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.

Power conditions

The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery pack is installed and what the charge level is for the battery.

Table 6-1 Power conditions

Power on Power off

(no operation)

• LED: Battery green

DC IN green

AC adaptor connected

Battery fully charged

Battery partially charged or no charge

• Operates

• LED: Battery green

DC IN green

• Operates

• Quick Charge

• LED: Battery orange

DC IN green

No battery installed

• Operates

• No charge

• LED: Battery off

DC IN green

• Quick charge

• LED: Battery orange

DC IN green

• No charge


DC IN green



Table 6-1 Power conditions continued

Power on Power off

(no operation)

AC adaptor not connected

Battery charge is above low battery trigger point

Battery charge is below low battery trigger point

Battery charge is exhausted

No battery installed

• Operates


DC IN off

• Operates

• LED: Battery flashes orange

DC IN off

Computer goes into resume mode shuts down

• Cannot operate


DC IN off

Power indicators

As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status.

Battery indicators

Check the Battery indicator to determine the status of the battery pack.

The following indicator lights indicate the battery status:

Flashing orange

The battery charge is low. The AC adaptor must be connected to recharge the battery.

Orange

Green

No light

Indicates the AC adaptor is connected and charging the battery.

Indicates the AC adaptor is connected and the battery is fully charged.

Under any other conditions, the indicator does not light.

If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out. When the battery pack’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off.

6-2 User’s Manual


DC IN indicator

Check the DC IN indicator to determine the power status with the AC adaptor connected:

Green

Flashing orange

No light

Indicates the AC adaptor is connected and supplying proper power to the computer.

Indicates a problem with the power supply.

Plug the AC adaptor into another power outlet.

If it still does not operate properly, contact your dealer.


Power indicator

Check the Power indicator to determine the power status:

Green

Indicates power is being supplied to the computer and the computer is turned on.

Blinking orange

No light

Indicates power is being supplied to the computer while the computer is in Standby mode. The indicator turns on for one second and off for two seconds.


Battery types

The computer has three types of batteries:

■ Battery pack

■ High capacity battery pack (option)

■ Real Time Clock (RTC) battery

Battery pack

When the AC adaptor is not connected, the computer’s main power source is a removable lithium ion battery pack, also referred to in this manual as the main battery. You can purchase additional battery packs for extended use of the computer away from an AC power source.

Before you remove the battery pack, set the computer to Hibernation mode or save your data and shut down the computer. Do not change the battery pack while the AC adaptor is connected.

User’s Manual 6-3


■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.

■ Do not remove the battery pack while the computer is in Standby mode.

Data is stored in RAM, so if the computer loses power it will be lost.

When the computer is powered off in Standby mode, and the AC adaptor is not connected, the battery pack supply power to maintain data and program in memory. If the battery pack is completely discharged, Standby mode does not function and the computer loses all data in memory .

To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge. It may not function efficiently over the expected life of the battery and the Battery indicator may not indicate a low-battery condition.

High capacity battery pack (option)

An optional High capacity battery pack is installable instead of a main battery pack. The connection method of High capacity battery pack is the same as that of main battery pack.

■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.

■ Do not remove the battery pack while the computer is in Standby mode.

Data is stored in RAM, so if the computer loses power it will be lost.

When the computer is powered off in Standby mode, and the AC adaptor is not connected, the main battery pack supply power to maintain data and program in memory. If the battery pack is completely discharged, Standby mode does not function and the computer loses all data in memory.

■ Do not have only High capacity battery pack, when having connected

High capacity battery pack with the computer.

6-4 User’s Manual

No results