Workzone Titanium+ AG36 Instruction Manual

Xfinity Li-ION 20V

Cordless Angle Grinder

Instruction Manual

MODEL NUMBER

AG36

Version number: 003

IMPORTANT

Read carefully before use

Keep for future reference

1 x 20V Angle Grinder

Skin

1 x Side Handle

1 x Pin Wrench

5 x Assorted Cutting

Discs

1 x Instruction Manual

1 x Warranty Certificate

1300 889 028

MODEL: AG36 [email protected]

PRODUCT CODE: 8290 06/2019

2

Welcome

Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion

Cordless Angle Grinder (battery / charger not included).

All products bought to you by Workzone® Titanium are manufactured to the highest standards of performance and safety and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 5 Year Warranty. We hope you will enjoy your purchase for many years to come.

When you open your packaging, first remove all items and check there are no parts damaged or missing. If you find anything wrong, do not operate the product until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

AFTER SALES SUPPORT

1300 889 028 (toll free)

2 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

Contents

Application 4

Package Content List

Parts description

Description of symbols

General safety warnings

Important information-Product care

Operation 22

Maintenance 24

Warranty 25

Environmental protection

Accessories and After Sales Parts

26

FAQ/Troubleshooting 28

Technical Specifications

27

30

4

5

6

7

16

Assembly 17

3

AFTER SALES SUPPORT

1300 889 028 (toll free)

3 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

4

20V Li-ion Cordless Angle Grinder

1. Application

First time users or inexperienced operators pay particular attention to the operation of the 20V Li-ion Cordless Angle Grinder, including details of starting and stopping and correct use of the 20V Li-ion Cordless Angle

Grinder on pages 22-23, as well as the maintenance instructions on pages 24.

Intended use of 20V Li-ion Cordless Angle Grinder (battery / charger not included)

NOTE: This product is for private domestic DIY use only. It is not suitable for commercial or trade use.

This 20V Li-ion Cordless Angle Grinder is used for general purpose grinding tasks on metal and stone.

The tool is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse.

2. Package Content List

1 x 20V Li-Ion Cordless Angle Grinder Skin

1 x Carry Case

1 x Auxiliary handle with pin wrench

5 x Grinding discs

1 x Wheel guard for grinding

1 x Instruction manual

1 x Warranty Card & Certificate

• Remove all packing materials

• Ensure all parts on the contents list are present

• Check the appliance, and all accessories for transportation

Damages

WARNING!

Please read and understand this instruction manual before use and keep it for your future reference. Your power tool should only be passed on together with this instruction manual.

WARNING! To reduce risk of injury, only use the ALDI Xfinity Plus range of 20V Li-Ion battery packs. Other type of battery packs may burst causing personal injury and damage. The battery pack must be charged using with ALDI Xfinity Plus 20V Li-Ion battery chargers.

AFTER SALES SUPPORT

1300 889 028 (toll free)

4 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

3. Parts description

1. Spindle lock button

2. Auxiliary handle position x 3

3. On/off switch

4. Main handle

8. Pin wrench

9. Grinding disc x 5

10. Wheel guard for grinding

11. Outer flange

5. Battery release button*

6. Battery pack*

12. Inner flange

13. Carry case

7. Auxiliary handle

* Battery not included. Shown only for instructional purposes.

5

2 3 4

1

6

9

10

11

12

AFTER SALES SUPPORT

1300 889 028 (toll free)

7

2

8

13

5 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

2

5

6

4. Description of symbols

The instruction manual, rating plate, or on the product itself, may show these symbols. These represent important information about the product or instructions on its use.

Warning

To reduce the risk of injury, user must read instruction manual

Wear ear protection

Wear eye protection

Wear breathing protection

Not permitted for face grinding with abrasive cutting off wheels

Do not use broken grinder

Wear protective gloves

Not permitted for wet grinding

Conforms to relevant standards for electrical safety and electromagnetic compatibility.

60 60 Months Warranty

AFTER SALES SUPPORT

1300 889 028 (toll free)

6 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

5. General safety warning

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAFETY INSTRUCTIONS

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water

AFTER SALES SUPPORT

1300 889 028 (toll free)

7 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

7

8 entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on . A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

AFTER SALES SUPPORT

1300 889 028 (toll free)

8 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

f) Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards.

4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

AFTER SALES SUPPORT

1300 889 028 (toll free)

9 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

9

10 g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety instructions for all operations

Safety Warnings Common for Grinding or Abrasive Cutting-

Off Operations:

AFTER SALES SUPPORT

1300 889 028 (toll free)

10 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

a) This power tool is intended to function as a grinder, sander, wire brush, polisher or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

b) Operations such as sanding, wire brushing or polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.

c) Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.

d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory,

AFTER SALES SUPPORT

1300 889 028 (toll free)

11 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

11

12 position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this test time.

h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations . The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.

k) Never lay the power tool down until the accessory has come to a complete stop.

The spinning accessory may grab the surface and pull the power tool out of your control.

l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

m)Regularly clean the power tool’s air vents. of powdered metal may cause electrical hazards.

The motor’s fan will draw the dust inside the housing and excessive accumulation

AFTER SALES SUPPORT

1300 889 028 (toll free)

12 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

n) Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.

Further safety instructions for all operations

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces.

Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up.

The operator can control torque reactions or kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of

AFTER SALES SUPPORT

1300 889 028 (toll free)

13 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

13

14 snagging.

d) Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specific for Grinding and Abrasive Cutting-

Off Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.

c) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.

d) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

AFTER SALES SUPPORT

1300 889 028 (toll free)

14 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

15 f) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive Cutting-Off

Operations: a) Do not “jam” the cut-off wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

f) Use extra caution when making a “pocket cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

AFTER SALES SUPPORT

1300 889 028 (toll free)

15 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

16

6.Important information – Product care

NOTE: Xfinity Battery and Charger not included. For any issuses related directly to your purchased ALDI Xfinity Plus 20V Li-Ion

Battery / charger, contact the Customer Service of the manufacturer as listed on the battery / charger packaging, manual or on the label on the battery / charger.

This Impact driver uses Lithium Ion Battery Cells. Care MUST be taken to ensure both the safety and life of the pack is maintained.

Ensure you have read all of the safety notes in the previous pages before using the Impact driver.

Treat the battery pack with care and within the guidelines of this manual.

If the battery pack does become immersed in water or any fluids, or is subject to a severe drop or it does not operate within the guidelines of this manual or the supplied manual, immediately STOP using the battery pack and have it checked.

Use only ALDI Xfinity Plus 20V Li-Ion range of chargers and 20V Li-

Ion batteries.

AFTER SALES SUPPORT

1300 889 028 (toll free)

16 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

7. Assembly

7.1 Attaching / removing auxiliary handle (7) (see fig. A1-A3)

NOTE: The grinder must only be operated with the auxiliary handle

(7) mounted.

You have the option of three auxiliary handle positions (2) to provide the safest and most comfortable control of your angle grinder depending on how you work. The handle (7) can be screwed clockwise into anyone of the auxiliary handle positions (2) on the top, left or right sides of the machine head.

A1 A2 A3

17

7.2 Fitting the grinding disc (9) (see fig. B1-B6 )

WARNING: Always ensure that the grinder is switched off and the battery pack (6) is removed before making any adjustments.

1) Take out the pin wrench (8) from the auxiliary handle (7).

NOTE: Please pay attention to the inserting direction of the pin wrench (8) while storing it in the auxiliary handle (7).

The raised pins on the side of the pin wrench (8) only allow the pin wrench to be inserted one way inside the auxiliary handle (7). If the pin wrench doesn’t fit when inserting one way, turn it around and insert the other way.

2) Remove the outer flange by rotating it in an anti-clockwise

AFTER SALES SUPPORT

1300 889 028 (toll free)

17 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

18 direction.

3) Place the grinding disc (9) onto the inner flange (12).

4) Place the outer flange (11) onto the grinding disc (9).

NOTE: Fit the threaded outer flange (11) making sure it is facing in the correct direction. For grinding discs, the flange is fitted with the raised portion facing towards the disc. See Fig. B5 for reference.

5) Rotate the outer flange (11) in a clockwise direction until it is secure by hand. To further fully secure the outer flange, press in and engage the spindle lock button (1) then use the pin wrench (8) on the outer flange (11) holes and further secure in a clockwise direction.

B1 B2 B3

B4 B5 B6

AFTER SALES SUPPORT

1300 889 028 (toll free)

18 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

7.3Adjusting the wheel guard (10) (see fig. C1-C7)

WARNING:Always ensure that the grinder is switched off and the battery pack (6) is removed before making any adjustments.

• The grinder must only be operated with the wheel guard

(10) installed.

WARNING: When using the angle grinder with a cutting disc, a wheel guard for cutting (not included) must be fitted prior to operation. Failure to do so may result in serious injury.

This angle grinder is supplied with a wheel guard for grinding, to be used with the grinding discs supplied. The size of the supplied grinding discs are: 125mm diamater x 22.23mm bore x 6mm thickness.

The supplied wheel guard for grinding is not suitable for cutting discs.

NOTE: Before using, adjust the wheel guard (10) so that any flying sparks or detached parts will not hit either the user or bystanders.

1) Take out the pin wrench (8) from the auxiliary handle (7).

2) Press in the spindle lock button (1) ensuring it is engaged and keep it pressed in, then, loosen the outer flange (11) in an anticlockwise direction with the pin wrench (8).

3) Remove the outer flange (11), grinding disc (9) and the inner flange (12).

4) Loosen the 3 screws a little, using a philips head screwdriver (not supplied) in an anti-clockwise direction.

5) Hold the wheel guard (10) and rotate it to the required position.

NOTE: The notches must be located in each groove while positioning.

AFTER SALES SUPPORT

1300 889 028 (toll free)

19 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

19

20

6) Re-tighten the 3 screws. Replace the inner flange (12), grinding disc (9) and outer flange (11) per previous instructions.

7) Press in the spindle lock button (1) and rotate the outer flange

(11) by hand until it is locked. Keeping the spindle lock button (1) pressed in, tighten the outer flange (11) with the spanner (8) per previous instructions.

C1 C2 C3

C4 C5 C6

C7

AFTER SALES SUPPORT

1300 889 028 (toll free)

20 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

7.4 Installing and removing the battery pack (6) a) To remove the battery pack (6) (see fig. D1)

Depress the battery pack release button (5) firmly, then slide the battery pack (6) out away from the tool.

b) To install the battery pack (6) (see fig. D2)

Slide the fully charged battery pack (6) onto the tool with sufficient force until it clicks into position.

D1 D2

21

AFTER SALES SUPPORT

1300 889 028 (toll free)

21 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

22

8.Operation

IMPORTANT: Before starting the angle grinder, ensure that the workpiece is secure i.e clamp the work piece so it is securely held down. A non secured work piece can cause injury to the user during operation.

8.1 Switch on/off (see fig. E1, E2)

To start the grinder, first press back the rear of the on/off switch (3), then push the on/off switch (3) forward.

To lock the on/off switch (3), press the on/off switch down at the front until it engages.

To switch off the grinder, briefly press down the back of the on/off switch (3) and then release it.

E1 E2

8.2 To use the grinder (see fig. F)

Attention: Do not switch the grinder on while the disc is in contact with the workpiece. Allow the disc to reach full speed before starting grinding.

1) Hold your angle grinder with one hand on the main handle (4) and other hand firmly around the auxiliary handle (7).

2) Ensuring that your work piece is secure, place the grinding disc

(9) with a light, even pressure on the work surface for maximum grinding efficiency. It should never be necessary to operate

AFTER SALES SUPPORT

1300 889 028 (toll free)

22 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

the product with increased force. The weight of the product generates enough pressure. Too much pressure will overload the motor, slow down the grinding process, and put dangerous pressure on the grinding disc (9) causing damage.

3) Move the grinder evenly back and forth.

4) Always position the guard (10) so that as much of the exposed disc (9) as possible is pointing away from you.

5) Be prepared for a stream of sparks when the disc touches the material.

6) For best tool control, material removal and minimum overloading, keep an angle between the disc (9) and the workpiece surface at approximately 15° to 30° when grinding.

7) Use cautiously when working into corners as contacting with the intersecting surface may cause the grinder to jump or twist.

8) When grinding is complete, allow the workpiece to cool. Do not touch the hot surface.

F

23

15°-30°

AFTER SALES SUPPORT

1300 889 028 (toll free)

23 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

24

9.Maintenance

Warning! Always ensure that the grinder is switched off and the battery pack (6) is removed before making any adjustments.

There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots.

This is normal and will not damage your power tool. Temperature range for the charging system during charging is 0°C-40°C.

AFTER SALES SUPPORT

1300 889 028 (toll free)

24 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

10.Warranty

Your new WORKZONE ® TITANIUM 20V Li-ion Cordless Angle Grinder will more than satisfy your expectations.

It has been manufactured under stringent WORKZONE ®

Quality Standards to meet superior performance criteria.

TITANIUM

You will find your new 20V Li-ion Cordless Angle Grinder easy and safe to operate, and, with proper care, it will give you many years of dependable service.

CAUTION. Carefully read through this entire instruction manual before using your new WORKZONE ® TITANIUM 20V Li-ion Cordless

Angle Grinder. Take special care to heed the Cautions and Warnings.

Your WORKZONE ® TITANIUM 20V Li-ion Cordless Angle Grinder has many features that will make your job faster and easier. Safety, performance, and dependability have been given top priority in the development of this 20V Li-ion Cordless Angle Grinder, making it easy to maintain and operate.

Use only WORKZONE ® TITANIUM replacement parts for your product. Non-conforming parts or modifications made to parts will void your warranty.

25

AFTER SALES SUPPORT

1300 889 028 (toll free)

25 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

26

What your 5 year warranty means

Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly.

In the event of product failure within its intended use over the course of as quickly as possible once it has been brought to our attention. In the unlikely event of such an occurrence, or if you require any information about the product please contact us via our after sales support services, details of which can be found in this manual and on the product itself.

After Sales Support TEL: 1300 889 028

Service Support

If you have any issues with the operation of your product, please call our Customer Service on 1300 889 028 for advice, or email us at [email protected]

11.Environmental protection

Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be sorted, taken to the local recycling centre and disposed of in an environmentally safe way.

AFTER SALES SUPPORT

1300 889 028 (toll free)

26 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

12.Accessories and After Sales Parts

The following is available for purchase by visiting https://help.tools/ or calling our customer service hotline on: 1300 889 028

27

1. 8290-GDG: Grinding Disc Guard 2. 8290-GD: 5 x Grinding Discs

AFTER SALES SUPPORT

1300 889 028 (toll free)

27 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

28

13. FAQ/Troubleshooting

Working hints for your angle grinder

1) Always start at no load to achieve maximum speed then start working.

2) Do not force the disc to work faster; reducing the disc’s moving speed means longer working time.

3) Always work with a 15-30 degrees between disc and workpiece.

Larger angles will cut ridges into the workpiece and affect the surface finish. Move the angle grinder across and back and forth over the workpiece.

4) When using a cutting disc never change the cutting angle otherwise you will stall the disc and angle grinder motor or break the disc. When cutting, only cut in the opposite direction to the disc rotation. If you cut in the same direction as the disc rotation the disc may push itself out of the cut slot.

5) When using a diamond disc it will become very hot. If this happens you will see a full ring of sparks around the rotating disc.

Stop cutting and allow to cool at no load speed for 2-3 minute

AFTER SALES SUPPORT

1300 889 028 (toll free)

28 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

Troubleshooting

Symptom

Grinding disc wobbles or vibrates

Cause

The outer flange is not tightened.

Solution

Tighten the outer flange

The disc is not correctly located on the flange plate.

Disc disintegrates Disc is old

The Battery pack gets warm when charging.

The fault cannot be rectified.

Re-locate the disc on the flange plate.

Remove it and replace with a new disc

This is normal.

It’s a result of the stepping down of the chemical reactions inside the batteries during the charging process.

The tool needs to Contact Customer be repaired.

Service

For further inquiries or issues associated with your tool, call our

Customer Service on 1300 889 028 or email us at [email protected]

29

AFTER SALES SUPPORT

1300 889 028 (toll free)

29 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

30

14. Technical Specification

Voltage

Rated speed

Disc diameter

Disc thickness

Disc bore

Spindle thread

Product Dimensions (L x W x H):

Machine weight

20V d.c.

10000 /min

125 mm

6 mm

22.23

M14

315*270*120

1.8 kg

This 20V Li-ion Cordless Angle Grinder complies with the following Standards:

Safety: EN 60745-1

EN 60745-2-3

AS/NZS 60745.1

AS/NZS 60745.2.3

EMC: EN 55014-1:2017

EN 55014-2: 2015

AFTER SALES SUPPORT

1300 889 028 (toll free)

30 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

20V Li-Ion Cordless Angle Grinder

Warranty Details

REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion. T conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

31

AFTER SALES SUPPORT

1300 889 028 (toll free)

31 e-mail: [email protected]

MODEL No.: AG36 • 8290• 06/2019

32

20V Li-Ion Cordless Angle Grinder

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such as les stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console or es stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or use refurbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they meet

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint.

Please call us on 1300 889 028, or email us at [email protected]

Positec Australia Pty Limited, 10 Corporate Blvd, Bayswater Victoria, Australia 3153

Positec Help Desk 1300 889 028 (Operating Hours: Mon-Fri 09:00AM to 05:00PM EST)

EMAIL: [email protected]

INTERNET: https://help.tools/

AFTER SALES SUPPORT

1300 889 028 (toll free)

32 e-mail: [email protected]

MODEL No.: AG36 • 8290 • 06/2019

This is a blank page

This is a blank page

This is a blank page

ALDI guarantees that our exclusive brand products are developed store within 60 days from the date of purchase for a full refund or replacement, or take advantage of our after sales support by calling the supplier‘s Customer Service Hotline.

WORKZONE TITANIUM ® is a registered t rademark of ALDI Stores

Made in China

WORKZONE TITANIUM ® is a registered t rademark of ALDI Stores

DISTRIBUTED BY:

ALDI STORES

1 SARGENTS ROAD, MINCHINBURY NSW 2770 www.aldi.com.au

1 x 20V Angle Grinder

Skin

1 x Side Handle

1 x Pin Wrench

5 x Assorted Cutting

Discs

1 x Instruction Manual

1 x Warranty Certificate

1300 889 028

MODEL: AG36 [email protected]

PRODUCT CODE: 8290 06/2019