advertisement
MANUAL
ENGLISH
Helix S5000 Q4 V1
Ordercode: 43725
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Helix S5000 Q4
Table of contents
Ordercode: 43725 1
Helix S5000 Q4
Ordercode: 43725 2
Helix S5000 Q4
Ordercode: 43725 3
Helix S5000 Q4
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Showtec Helix S5000 Q4
● Schuko to Neutrik PowerCON True1 power cable (1,5 m)
● 6 x quick-locks
● 2 x quick-lock brackets
● 4 x rubber feet
● 1 x mounting bracket
● User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is significantly reduced. If improving your lifespan expectancy is of a higher priority, place care in providing for lower operational temperatures. This may include climatic-environmental and the reduction of overall projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Ordercode: 43725 4
Helix S5000 Q4
Before your initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
● Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution!
● Never remove warning or informative labels from the unit.
● Never use anything to cover the ground contact.
● Never place any material over the lens.
● Never look directly into the light source.
● Never leave any cables lying around.
● Do not insert objects into air vents.
● Do not connect this device to a dimmer pack.
● Do not switch the device on and off in short intervals, as this would reduce the device’s life.
● Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at least 5 minutes before handling.
● Do not shake the device. Avoid brute force when installing or operating the device.
● Only use device indoors, avoid contact with water or other liquids.
● Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly fastened.
● Only operate the device after having familiarized with its functions.
● Avoid flames and do not put close to flammable liquids or gases.
● Always keep case closed while operating.
● Always allow free air space of at least 50 cm around the unit for ventilation.
● Always disconnect power from the mains, when device is not used or before cleaning! Only handle
● the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
● Make sure that the available voltage is not higher than stated on the rear panel.
● Make sure that the power cord is never crimped or damaged. Check the device and the power cord from time to time.
● If the lens is obviously damaged, it has to be replaced, so that its functions are not impaired due to cracks or deep scratches.
● If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer inspect for safety before operating.
● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
● If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
● For adult use only. Device must be installed out of the reach of children. Never leave the unit running unattended.
● Never attempt to bypass the thermostatic switch or fuses.
● The user is responsible for correct positioning and operating of the Helix. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
Ordercode: 43725 5
Helix S5000 Q4
● This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
● Repairs, servicing and electric connection must be carried out by a qualified technician.
● WARRANTY: Till one year after date of purchase.
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
● The minimum distance between light output and the illuminated surface must be bigger than 0,5 meter.
● The maximum ambient temperature ta = 40°C must never be exceeded.
● In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely disconnect from power source via breaker or by unplugging.
● The relative humidity must not exceed 50 % with an ambient temperature of 40°C.
● If this device is operated in any other way, than the one described in this manual, the product may
● suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other safety issues.
Do not attempt the installation yourself!
Always let the installation be carried out by an authorized dealer!
Procedure:
● If the Helix is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the Helix, with the mounting bracket, to the trussing system.
● The Helix must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety cable.
● When rigging, derigging or servicing the Helix, always make sure, that the area below the installation place is blocked and staying in the area is forbidden.
Ordercode: 43725 6
Helix S5000 Q4
The Helix S5000 Q4 can be placed on a flat stage floor, by means of the included mounting bracket, or be mounted to any kind of truss with clamps and quick-locks.
Improper installation can cause serious damage to people and property!
Ordercode: 43725 7
Helix S5000 Q4
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
L
EU Cable
BROWN
UK Cable
RED
US Cable
YELLOW/COPPER
N BLUE
YELLOW/GREEN
BLACK
GREEN
SILVER
GREEN
Pin
PHASE
NEUTRAL
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [email protected]
and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting.
Ordercode: 43725 8
Helix S5000 Q4
Description of the device
Features
The Showtec Helix S5000 Q4 is a high-power panel light with IP65 protection grade. It has an extremely high light output and is very suitable for illumination of larger indoor and (temporarily) outdoor areas.
● Wireless DMX (Wireless Solutions)
● Quick-locks for fast rigging and mounting
● DMX control via standard DMX controller
● Onboard: OLED display for easy setup
● Input voltage: 100-240V AC, 50/60Hz
Power consumption: 415W ●
● Peak power: 810W
● Light source: 40 x Prolight Opto RGBW 4-in-1 10W LEDs
● Light output @ 2m: 54000 lux
● Refresh rate: 3.0 kHz
● DMX modes: 4, 6, 8, 20, 24 channels
● Dimmer: 0-100%
● Strobe: 0-20Hz
● Beam angle: 10°
● Control mode: Auto, Built-in programs, Manual, Master/Slave, DMX512, W-DMX
● Housing: Die-cast aluminum
● Power connectors: Neutrik PowerCON True1 IN/OUT
● Data connectors: 5-pin XLR-HD DMX IN/OUT
●
● IP rating: IP65
● Working temperature: -10°C ~40°C
●
Cooling: Cooling fans
Dimensions: 530 x 125 x 318 mm (LxWxH)
● Weight: 11,5 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
43726 – Barndoor for Helix S5000 Q4
43727 – Beamshaper for Helix S5000 Q4 (20°)
43728 – Beamshaper for Helix S5000 Q4 (45°)
43729 – Beamshaper for Helix S5000 Q4 (15°x60°)
43730 – Tophat for Helix S5000 Q4
50177 – W-DMX™ BlackBox F-1 G5 Transceiver
50178 – W-DMX™ BlackBox F-2 G5 Transceiver
D7249 – Case for 4 x Helix 4000
Ordercode: 43725 9
Helix S5000 Q4
Overview
Fig. 01
01) 40 x Prolight Opto RGBW 4-in-1 10W LEDs
02) 5-pin DMX connector IN
03) 5-pin DMX connector OUT
04) 100-240V Neutrik PowerCON True1 power connector OUT
05) 100-240V Neutrik PowerCON True1 power connector IN
06) OLED display + control buttons
07) Pressure valve
This valve manages the air pressure within the Helix’s enclosure. It allows the enclosure to breathe, equalizes pressure and reduces condensation while filtering out liquids and other contaminants. By doing so, it increases the Helix’s performance and durability.
08) Antenna for wireless DMX
09) Adjustment screw
Ordercode: 43725 10
Helix S5000 Q4
Installation
Remove all packing materials from the Helix S5000 Q4. Check that all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Installing the Barndoor (43726)
01) Pull on the spring-loaded locking screws, on both sides of the barndoor, to unlock the mechanism.
Fig. 02
02) Place the barndoor on the Helix, to secure the barndoor’s screws in the Helix’s mounting holes.
03) Release both locking screws to lock the barndoor in position.
Ordercode: 43725 11
Fig. 03
Helix S5000 Q4
Installing the Beamshapers (43727/43728/43729)
01) In order to install the beamshaper, place it on the lens of the Helix. The beamshaper is equipped with
02) multiple magnets which keep it firmly in position.
In order to remove the beamshaper, pull it by the handles located on its sides.
Fig. 04
Ordercode: 43725 12
Helix S5000 Q4
Installing the Tophat (43730)
01) Pull on the spring-loaded locking screws, on both sides of the tophat, to unlock the mechanism.
02) Place the tophat on the Helix, to secure the tophat’s screws in the Helix’s mounting holes.
Fig. 05
03) Release both locking screws to lock the tophat in position.
Fig. 06
Ordercode: 43725 13
Helix S5000 Q4
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Control Modes
There are 6 modes: ● Auto
● Built-in Programs
● Manual
● Master/Slave
● DMX512 (4CH, 6CH, 8CH, 20CH, 24CH)
● Wireless DMX control
One Helix (Auto, Built-in Programs)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Helix is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see pages 25-27 for more information about Auto and Built-in programs.
One Helix (Manual Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Helix is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 25 for more information about Manual mode.
Multiple Helixes (Master / Slave Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 5-pin XLR cable to connect the Helix.
The pins: 01) Earth
02) Signal (-)
03) Signal (+)
04) N/C
05) N/C
05) Link the units as shown in fig. 07. Connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second and third units. You can use the same functions on the master device as described on pages 23-27. This means that you can set your desired operation mode on the master device and all slave devices will react the same as the master device.
Multiple Helixes (Master/Slave Set Up)
Ordercode: 43725 14
Fig. 07
Helix S5000 Q4
Multiple Helixes (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 5-pin XLR cable to connect the Helix and other devices.
05) Link the units as shown in fig. 08. Connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second and third units.
06) Supply electric power: Plug electric mains power cords into each unit's PowerCON True1 socket, then plug the other end of the mains power cord into proper electric power supply sockets, starting with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Helixes (DMX Set Up)
Note: Link all cables before connecting electric power!
Fig. 08
Ordercode: 43725 15
Helix S5000 Q4
Multiple Helixes (Wireless DMX Control)
You can use the Helix in a wireless DMX setup. Make sure the device is operating in wireless DMX mode, which can be set in the main menu (see pages 24-25 for more information).
Sweden 2.4GHz Wireless Communication Module
Communication distance:
Test conditions: depending on the transmitting power or transmitter module
W-DMX TRx Transmitter module, 2dBi Antenna, transmitting power
20dBm (100mW)
Range indoor:
Range outdoor:
60 m (approx. through three concrete walls)
250 m
Wireless DMX Connection
The wireless receiving module “Nano G5 Receiver, 2.4GHz”, provided by Swedish WIRELESS SOLUTION, only has a 2.4 GHz wireless signal receiving function. In order to establish a wireless connection, please use the Wireless DMX BlackBox F-1 G5 Transceiver (50177) or the Wireless DMX BlackBox F-2 G5 Transceiver
(50178). To control the status of the wireless communication, please look at the green LED indicator light on the left side of the display.
Note: When the Helix receives a wireless DMX signal, then this signal will also be present at its 5-pin DMX output (03). However, the Helix has not been designed to send wireless signals. Therefore, always connect the Helix devices to each other using a DMX cable.
Wireless DMX Problems
01) No signal from the W-DMX transmitter.
The LED indicator will blink quickly.
Proper connection with the W-DMX transmitter, but no DMX signal is present. 02)
The LED indicator will blink slowly.
When the wireless DMX communication is unhindered and a DMX signal is present, the LED indicator will always be on.
The Helix S5000 Q4 cannot receive a Wireless DMX signal and a DMX cable signal at the same time
When the device is in Auto mode or Built-in Programs mode, please ensure that the paired 2.4GHz wireless signal transmitter is OFF.
The Helix S5000 Q4 is only a WDMX receiver and never a WDMX transmitter
Ordercode: 43725 16
Helix S5000 Q4
Example 1
The Helix cannot send any wireless signals. Therefore, the slave Helix fixtures must always be connected via a DMX signal cable.
The Helix S5000 Q4 is only a WDMX receiver and never a WDMX transmitter
When the Helix operates in DMX or Slave mode, it can receive a wireless DMX signal (CH1-512) and at the same time it can also send a DMX signal, via its DMX output (03), through a DMX cable.
Fig. 09
Ordercode: 43725 17
Helix S5000 Q4
Example 2
The Showtec Operator Air (50726) sends out a wireless signal with 512 channels and the Helix picks up this signal.
Connect the Helix to the wireless DMX signal transmitter
The Helix S5000 Q4 cannot actively search for wireless signal transmitters.
In order to pair the Helix with the wireless signal transmitter, please check the manual of the wireless signal transmitter you use.
It is recommended to use the Wireless DMX BlackBox F-1 G5 Transceiver (50177) or the Wireless DMX
BlackBox F-2 G5 Transceiver (50178).
Disconnect from the Wireless DMX signal transmitter
The Helix can be disconnected from the wireless DMX signal transmitter.
It is possible to deactivate W-DMX in the main menu, see pages 24-25 for more information.
Ordercode: 43725 18
Fig. 10
Helix S5000 Q4
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master / slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link @110V: 3 fixtures
Maximum recommended number of fixtures on a power link @240V: 7 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
DAP Audio DMX Data Cables
● DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
●
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
● DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
● DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
● DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin. Ordercode FL08150 (1,5 m),
●
● DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
● DAP Audio DMX Terminator 3-pin. Ordercode FLA42.
●
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
DAP Audio DMX adapter: 5-pin/3-pin. Ordercode FLA29.
DAP Audio DMX Terminator 5-pin. Ordercode FLA43.
Note: connect the Helix S5000 Q4 with the dedicated special XLR cables for outdoor use.
FL83150 – Neutrik DMX Cable 5-pin XLR IP65 (1,5 m)
FL833 – Neutrik DMX Cable 5-pin XLR IP65 (3 m)
FL836 – Neutrik DMX Cable 5-pin XLR IP65 (6 m)
FL8310 – Neutrik DMX Cable 5-pin XLR IP65 (10 m)
FL8320 – Neutrik DMX Cable 5-pin XLR IP65 (20 m)
Ordercode: 43725 19
Helix S5000 Q4
Control Panel
A) DMX LED indicator
B) OLED display
C) MODE button
D) DOWN button
E) UP button
F) SET button
Fig. 11
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign the DMX fixture address, which is the first channel from which the Helix will respond to the controller.
Please note when you use the controller, the unit has 24 channels.
When using multiple Helixes make sure you set the DMX addresses right.
Therefore, the DMX address of the first Helix should be 1(001); the DMX address of the second Helix should be 1+24=25 (025); the DMX address of the third Helix should be 25+24=49 (049), etc. Please, be sure that you do not have any overlapping channels in order to control each Helix correctly. If two or more Helixes are addressed similarly, they will work similarly.
Controlling:
After having addressed all Helix fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Helix will automatically detect whether DMX 512 data is received or not. The problem may be:
● The XLR cable from the controller is not connected with the input of the Helix.
● The controller is switched off or defective, the cable or connector is defective, or the signal wires are swapped in the input connector.
Note: It is necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure proper transmission on the DMX data link.
Display Off after 30 seconds
When no button is pressed for 30 seconds, the display will turn off.
To unlock the display, you have to press and hold down the MODE and SET buttons for 3 seconds. Once you have pressed the buttons, the display will light up.
Ordercode: 43725 20
Helix S5000 Q4
Menu Overview
Ordercode: 43725 21
Helix S5000 Q4
Ordercode: 43725 22
Helix S5000 Q4
Main Menu Options
1.
DMX settings
2.
Manual mode
3.
Auto mode
4.
Built-in programs
5.
Master/Slave mode
6.
Settings
7.
Information
Upon start-up, the display will show the current software version, temperature and the signal type.
1. DMX Settings
With this menu you can set the DMX address, choose the desired DMX mode and activate/deactivate the wireless DMX.
01) While in the main menu, press the UP/DOWN buttons to choose DMX.
02) Press the SET button to enter the menu. The display will show:
03) Press the UP/DOWN buttons to select one of the 4 submenus:
● Address
● Channels
● Signal
● W-DMX unlock
04) Press the SET button to open the desired submenu.
Ordercode: 43725 23
Helix S5000 Q4
1.1. Address
With this menu you can set the desired DMX starting address.
01) Press the UP/DOWN buttons to set the desired DMX address. The adjustment range is between 001-
512.
02) Press the SET button to confirm your choice.
1.2. Channels
With this menu you can set the desired DMX channel mode.
01) Press the UP/DOWN buttons to set the desired DMX channel mode. Choose one of the 5 options:
● 4 channels
● 6 channels
● 8 channels
● 20 channels
● 24 channels
02) Press the SET button to confirm your choice.
1.3. Signal
With this menu you can set the DMX signal type.
Press the SET button to confirm your choice.
01) Press the UP/DOWN buttons to set the desired DMX signal type. Choose one of the 2 options:
● DMX: conventional DMX
● W-DMX: wireless DMX
02)
Ordercode: 43725 24
Helix S5000 Q4
1.4. W-DMX Unlock
With this menu you can unlock the wireless DMX.
01) Press the UP/DOWN buttons to choose YES (to unlock the wireless DMX) or NO (to return to the previous screen).
02) Press the SET button to confirm your choice.
2. Manual Mode
With this menu you can manually set the desired color.
01) While in the main menu, press the UP/DOWN buttons to choose MANUAL.
02) Press the SET button to enter the menu. The display will show:
Press the SET button to enter the menu.
03) Press the UP/DOWN buttons to choose one of the 4 colors: Red, Green, Blue and White.
04)
05) Press the UP/DOWN buttons to set the intensity of the LEDs. The adjustment range for each color is between 0-255, from dark to brightest.
06) Press the SET button to save your settings.
07) You can combine Red, Green, Blue and White to create an infinite range of colors (0-255).
3. Auto Mode
With this menu you can set Auto mode.
01) While in the main menu, press the UP/DOWN buttons to choose AUTO.
02) Press the SET button to enter the menu. The display will show:
03)
04)
Press the UP/DOWN buttons to choose YES (to start the auto show) or NO (to return to the previous screen.
Press the SET button to confirm your choice.
Ordercode: 43725 25
Helix S5000 Q4
4. Built-in Programs
With this menu you can set the built-in programs.
01) While in the main menu, press the UP/DOWN buttons to choose PROGRAM.
02) Press the SET button to enter the menu. The display will show:
03) Press the UP/DOWN buttons to choose MODE and press the SET button to enter the menu.
04) The display will show:
05) Press the UP/DOWN buttons to choose one of the 26 built-in programs. Press the SET button to confirm your choice.
4.1. Program 01
01) If you have chosen program 01, the display will show:
02) Press the UP/DOWN buttons to choose one of the 2 options:
● COLOR
● STROBE
03) Press the SET button to enter the desired menu.
04) If you have chosen COLOR, press the UP/DOWN buttons to choose one of the 38 color macros. Press the SET button to save your settings.
05) If you have chosen STROBE, press the UP/DOWN buttons to set the strobe frequency. The adjustment range is between 0-99, from OFF to high frequency. Press the SET button to save your settings.
Ordercode: 43725 26
Helix S5000 Q4
4.2. Programs 02-26
01) If you have chosen one of the programs 02-26, the display will show:
02) Press the UP/DOWN buttons to choose one of the 2 options:
● SPEED
● STROBE
03) Press the SET button to enter the desired menu.
04) If you have chosen SPEED, press the UP/DOWN buttons to set the built-in program’s speed. The adjustment range is between 1-100, from slow to fast. Press the SET button to save your settings.
05) If you have chosen STROBE, press the UP/DOWN buttons to set the strobe frequency. The adjustment range is between 0-99, from OFF to high frequency. Press the SET button to save your settings.
5. Master/Slave Mode
With this menu you can set the device as a slave.
01) While in the main menu, press the UP/DOWN buttons to choose SLAVE.
02) Press the SET button to enter the menu. The display will show:
05)
03) Press the UP/DOWN buttons to choose YES or NO.
04) Press the SET button to confirm your choice.
If you have chosen YES, the device will be set as a slave and will react the same as the master device.
Ordercode: 43725 27
Helix S5000 Q4
6. Settings
With this menu you can adjust the device’s settings.
01) While in the main menu, press the UP/DOWN buttons to choose SETTINGS.
02) Press the SET button to enter the menu. The display will show:
03) Press the UP/DOWN buttons to choose one of the 11 submenus:
● CURVES SELECT
● DIMMER SPEED
● FAN SPEED
● PIXEL DIR
● PWM FREQUENCY
● BACKLIGHT TIME
● DMX FAIL
● DMX SYNC
● LOCK
● KEY BACKLIGHT
● FACTORY
04) Press the SET button to enter the desired submenu.
6.1. Curves Select
01) Press the UP/DOWN buttons to choose one of the 4 dimming curves.
02) Press the SET button to confirm your choice.
Ordercode: 43725 28
Helix S5000 Q4
6.2. Dimmer Speed
With this menu you can set the dimmer speed.
01) Press the UP/DOWN buttons to select FAST or SMOOTH.
02) Press the SET button to confirm your choice.
6.3. Fan Speed
With this menu you can set the fan speed.
01) Press the UP/DOWN buttons to select AUTO, HIGH or SLOW.
02) Press the SET button to confirm your choice.
Ordercode: 43725 29
Helix S5000 Q4
6.4. Pixel Dir
With this menu you can set the pixel direction.
01) Press the UP/DOWN buttons to select NORMAL or INVERT.
02) Press the SET button to confirm your choice.
6.5. PWM Frequency
With this menu you can set the PWM frequency.
01) Press the UP/DOWN buttons to select 12K, 6K, 4K or 3K.
02) Press the SET button to confirm your choice.
6.6. Backlight Time
With this menu you can set the time which needs to pass before the display turns off, when no buttons are pressed.
01) Press the UP/DOWN buttons to select 5s, 10s, 20s, 30s or ON (display continuously on).
02) Press the SET button to confirm your choice.
Ordercode: 43725 30
Helix S5000 Q4
6.7. DMX Fail
With this menu you can set the device’s behavior in case of a DMX failure.
01) Press the UP/DOWN buttons to select one of the 4 options:
● OFF: the device will black out the light output
● HOLD: the device will use last properly received DMX signal, ensuring undisrupted performance
● MANUAL: the device will switch to Manual mode
● PROGRAM: the device will run the built-in programs
02) Press the SET button to confirm your choice.
6.8. DMX Sync
With this menu you can set the devices’ behavior, while using multiple Helixes.
01) Press the UP/DOWN buttons to select ON (all Helix devices will simultaneously perform the same
02) action, without any delays) or OFF (risk of random delays).
Press the SET button to confirm your choice.
6.9. Lock
With this menu you can set the safety lock, restricting access to the main menu.
01) Press the UP/DOWN buttons to select one of the 2 options:
● ON: when no button is pressed within the time limit set in menu 6.6. Backlight Time (see page 30), the device’s main menu will be locked. In order to unlock it, press and hold down the MODE and
SET buttons for 3 seconds.
● OFF: safety lock is inactive
02) Press the SET button to confirm your choice.
Ordercode: 43725 31
Helix S5000 Q4
6.10. Key Backlight
With this menu you can set whether the 4 buttons (MODE, SET, UP, DOWN) will be illuminated or not.
01) Press the UP/DOWN buttons to select ON or OFF.
02) Press the SET button to confirm your choice.
6.11. Factory
With this menu you can restore the default factory settings.
01) Press the UP/DOWN buttons to select YES or NO.
02) Press the SET button to confirm your choice.
7. Information
With this menu you can view the device’s current software version, temperature, total lifetime, type of
DMX signal and the device’s UID number.
01) While in the main menu, press the UP/DOWN buttons to choose INFORMATION.
02) Press the SET button to enter the menu. The display will show:
03) Press the UP/DOWN buttons to toggle through the screens.
Ordercode: 43725 32
Helix S5000 Q4
DMX Channels
4 Channels
Channel 1 – Red
0-255 Gradual adjustment Red, from dark to brightest
Channel 2 – Green
0-255 Gradual adjustment Green, from dark to brightest
Channel 3 – Blue
0-255 Gradual adjustment Blue, from dark to brightest
Channel 4 – White
0-255 Gradual adjustment White, from dark to brightest
6 Channels
Channel 1 – Dimmer
0-255 Dimmer intensity, from dark to brightest
Channel 2 – Red CH1 must be open
0-255 Gradual adjustment Red, from dark to brightest
Channel 3 – Green CH1 must be open
0-255 Gradual adjustment Green, from dark to brightest
Channel 4 – Blue CH1 must be open
0-255 Gradual adjustment Blue, from dark to brightest
Channel 5 – White CH1 must be open
0-255 Gradual adjustment White, from dark to brightest
Channel 6 – Strobe CH1 must be open; CH2-5 must be open
0-10 Not functional
11-255 Strobe flash frequency, from OFF to highest frequency
Ordercode: 43725 33
Helix S5000 Q4
8 Channels
Channel 1 – Dimmer
0-255 Dimmer intensity, from dark to brightest
Channel 2 – Red CH1 must be open; CH6-7 must be closed
0-255 Gradual adjustment Red, from dark to brightest
Channel 3 – Green CH1 must be open; CH6-7 must be closed
0-255 Gradual adjustment Green, from dark to brightest
Channel 4 – Blue CH1 must be open; CH6-7 must be closed
0-255 Gradual adjustment Blue, from dark to brightest
Channel 5 – White CH1 must be open; CH6-7 must be closed
0-255 Gradual adjustment White, from dark to brightest
166-175
176-185
186-195
196-205
206-215
216-225
226-235
236-245
246-255
Channel 6 – Color switch/Color flow CH1 must be open
0-5 Not functional
6-15
16-25
26-35
36-45
Color switch 1
Color switch 2
Color switch 3
Color switch 4
46-55
56-65
66-75
76-85
Color switch 5
Color switch 6
Color switch 7
Color switch 8
86-95
96-105
106-115
116-125
126-135
136-145
146-155
156-165
Color flow 1
Color flow 2
Color flow 3
Color flow 4
Color flow 5
Color flow 6
Color flow 7
Section switch 1
Section switch 2
Section switch 3
Section switch 4
Section switch 5
Section flow 1
Section flow 2
Section flow 3
Section flow 4
Section flow 5
Channel 7 – Color switch/flow speed CH6 must be set between 6-255
0-255 Gradual speed adjustment, from slow to fast
Channel 7 – Color macros CH1 must be open; CH6 must be closed
0-10 Not functional
11-16
17-22
23-28
Red
Flame Red
Deep Gold Amber
Ordercode: 43725 34
Helix S5000 Q4
179-184
185-190
191-196
197-202
203-208
209-214
215-220
221-226
227-232
233-255
119-124
125-130
131-136
137-142
143-148
149-154
155-160
161-166
167-172
173-178
29-34
35-40
41-46
47-52
53-58
59-64
65-70
71-76
77-82
83-88
89-94
95-100
101-106
107-112
113-118
Millennium Gold
Gold Amber
Yellow
Chrome Yellow
Deep Amber
Spring Yellow
Lime Green
JAS Green
Fern Green
Moss Green
Primary Green
Dark Green
Green
Medium Blue Green
Light Blue
Lighter Blue
Steel Blue
½ CT Blue
Full CT Blue
State Blue
Double CT Blue
Medium Blue
Just Blue
Deep Blue
Blue
Congo Blue
Surprise Pink
Fuchsia Pink
Follies Pink
Special Rose Pink
Pink
Moroccan Pink
Warm White
Cold White
Open White
Channel 8 – Strobe CH1 must be open; CH2-7 must be open
0-10 Not functional
11-255 Strobe flash frequency, from OFF to highest frequency
Ordercode: 43725 35
Helix S5000 Q4
The Helix’s output is divided into 5 sections.
20 Channels
Channel 1 – Red (section 1)
0-255 Gradual adjustment Red, from dark to brightest
Channel 2 – Green (section 1)
0-255 Gradual adjustment Green, from dark to brightest
Channel 3 – Blue (section 1)
0-255 Gradual adjustment Blue, from dark to brightest
Channel 4 – White (section 1)
0-255 Gradual adjustment White, from dark to brightest
Channel 5 – Red (section 2)
0-255 Gradual adjustment Red, from dark to brightest
Channel 6 – Green (section 2)
0-255 Gradual adjustment Green, from dark to brightest
Channel 7 – Blue (section 2)
0-255 Gradual adjustment Blue, from dark to brightest
Channel 8 – White (section 2)
0-255 Gradual adjustment White, from dark to brightest
Channel 17 – Red (section 5)
0-255 Gradual adjustment Red, from dark to brightest
Channel 18 – Green (section 5)
0-255 Gradual adjustment Green, from dark to brightest
Channel 19 – Blue (section 5)
0-255 Gradual adjustment Blue, from dark to brightest
Channel 20 – White (section 5)
0-255 Gradual adjustment White, from dark to brightest
Ordercode: 43725 36
Helix S5000 Q4
The Helix’s output is divided into 5 sections.
24 Channels
Channel 1 – Dimmer
0-255 Dimmer intensity, from dark to brightest
Channel 2 – Strobe CH1 must be open; CH3-24 must be open
0-10 Not functional
11-255 Strobe flash frequency, from OFF to highest frequency
Channel 3 – Color switch/flow speed CH4 must be set between 6-255
0-255 Gradual speed adjustment, from slow to fast
101-106
107-112
113-118
119-124
125-130
131-136
137-142
143-148
149-154
155-160
161-166
167-172
Channel 3 – Color macros CH1 must be open; CH4 must be closed
0-10
11-16
Not functional
Red
17-22
23-28
29-34
35-40
Flame Red
Deep Gold Amber
Millennium Gold
Gold Amber
41-46
47-52
53-58
59-64
65-70
71-76
77-82
83-88
89-94
95-100
Yellow
Chrome Yellow
Deep Amber
Spring Yellow
Lime Green
JAS Green
Fern Green
Moss Green
Primary Green
Dark Green
Green
Medium Blue Green
Light Blue
Lighter Blue
Steel Blue
½ CT Blue
Full CT Blue
State Blue
Double CT Blue
Medium Blue
Just Blue
Deep Blue
Ordercode: 43725 37
Helix S5000 Q4
173-178
179-184
185-190
191-196
197-202
203-208
209-214
215-220
221-226
227-232
233-255
Blue
Congo Blue
Surprise Pink
Fuchsia Pink
Follies Pink
Special Rose Pink
Pink
Moroccan Pink
Warm White
Cold White
Open White
Channel 4 – Color switch/Color flow CH1 must be open
0-5 Not functional
6-15
16-25
Color switch 1
Color switch 2
26-35
36-45
46-55
56-65
66-75
76-85
Color switch 3
Color switch 4
Color switch 5
Color switch 6
Color switch 7
Color switch 8
86-95
96-105
106-115
116-125
126-135
136-145
146-155
156-165
166-175
176-185
186-195
196-205
206-215
216-225
226-235
236-245
246-255
Color flow 1
Color flow 2
Color flow 3
Color flow 4
Color flow 5
Color flow 6
Color flow 7
Section switch 1
Section switch 2
Section switch 3
Section switch 4
Section switch 5
Section flow 1
Section flow 2
Section flow 3
Section flow 4
Section flow 5
Channel 5 – Red (section 1) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Red, from dark to brightest
Channel 6 – Green (section 1) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Green, from dark to brightest
Channel 7 – Blue (section 1) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Blue, from dark to brightest
Channel 8 – White (section 1) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment White, from dark to brightest
Ordercode: 43725 38
Helix S5000 Q4
Channel 9 – Red (section 2) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Red, from dark to brightest
Channel 10 – Green (section 2) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Green, from dark to brightest
Channel 11 – Blue (section 2) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Blue, from dark to brightest
Channel 12 – White (section 2) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment White, from dark to brightest
Channel 21 – Red (section 5) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Red, from dark to brightest
Channel 22 – Green (section 5) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Green, from dark to brightest
Channel 23 – Blue (section 5) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment Blue, from dark to brightest
Channel 24 – White (section 5) CH1 must be open; CH3-4 must be closed
0-255 Gradual adjustment White, from dark to brightest
Maintenance
The Showtec Helix S5000 Q4 requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents. The front glass panel will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light output very quickly. Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
The operator has to make sure that safety-related and machine-technical installations are to be inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Ordercode: 43725 39
Helix S5000 Q4
Troubleshooting
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the internal fuse.
01) Power supply. Check if the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Helix to your Showtec dealer.
03) The internal fuse. Return the Helix to your Showtec dealer.
04) If all appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Helix, as this may damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
01)
03)
Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
Determine whether the controller or light effect is at fault. Does the controller operate properly with other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light effect to a qualified technician.
Problem
One or more fixtures do not function at all
Probable cause(s)
No power to the fixture
Internal fuse blown
Remedy
● Check if power is switched on and cables are plugged in
Fixtures reset correctly, but all respond erratically or not at all to the controller
The controller is not connected
5-pin XLR Out of the controller does not match XLR Out of the first fixture on the link (i.e. signal is reversed)
● Return the device to your Showtec dealer
● Connect controller
● Install a phase reversing cable between the controller and the first fixture on the link
Fixtures reset correctly, but some respond erratically or not at all to the controller
No light or LEDs cuts out intermittently
Poor data quality
Bad data link connection
Data link not terminated with 120
Ohm termination plug
Incorrect addressing of the fixtures
One of the fixtures is defective and disturbs data transmission on the link
5-pin XLR Out on the fixtures does not match (pins 2 and 3 reversed)
Fixture is too hot
LEDs damaged
The power supply settings do not match local AC voltage and frequency
● Check data quality. If much lower than
100 percent, the problem may be a bad data link connection, poor quality or broken cables, missing termination plug, or a defective fixture disturbing the link
● Inspect connections and cables. Correct poor connections. Repair or replace damaged cables
● Insert termination plug in output jack of the last fixture on the link
● Check address setting
● Bypass one fixture at a time until normal operation is regained: unplug both connectors and connect them directly together
● Have the defective fixture serviced by a qualified technician
● Install a phase-reversing cable between the fixtures or swap pin 2 and 3 in the fixture, that behaves erratically
● Allow the fixture to cool down
● Clean the fans
● Make sure air vents are not blocked
● Turn up the air conditioning
● Disconnect fixture and return to your dealer
● Disconnect fixture. Check settings and correct if necessary
Ordercode: 43725 40
Helix S5000 Q4
Product Specifications
Model:
Input voltage:
Power consumption:
Peak power:
Power linking:
DMX linking:
Dimensions:
Weight:
Operating and Programming:
Showtec Helix S5000 Q4
100-240V AC, 50/60Hz
415W
810W
3pcs@110V, 7pcs@240V
30pcs
530 x 125 x 318 mm (LxWxH)
11,5 kg
Signal pin OUT:
DMX Mode:
Signal input:
Signal output:
Electro-mechanical effects:
Light source:
Light output @ 2m:
Refresh rate:
Beam angle:
Dimmer:
Strobe:
Rigging:
Wireless DMX:
IP rating:
DMX control:
Onboard:
Control:
Pin 1 (earth), pin 2 (-), pin 3 (+)
4, 6, 8, 20, 24 channels
5-pin XLR-HD IN
5-pin XLR-HD OUT
40 x Prolight Opto RGBW 4-in-1 10W LEDs
54000 lux
3.0 kHz
10°
0-100%
0-20Hz
Quick-locks for fast rigging and mounting
Wireless Solutions
Housing:
Connections:
Cooling:
Working temperature:
Included:
Max. ambient temperature t a
: 40°C
IP65 via standard DMX controller
OLED display for easy setup
Auto, Built-in programs, Manual, Master/Slave, DMX512,
W-DMX
Die-cast aluminum
Dedicated PowerCON True1 power & data connector
Cooling fans
-10°C~40°C
Schuko to Neutrik PowerCON True1 cable (1,5 m)
Max. housing temperature t
B
: 70°C
Minimum distance:
Minimum distance from flammable surfaces: 0,5 m
Minimum distance to lighted object: 1 m
Design and product specifications are subject to change without prior notice.
Website:
www.Showtec.info
Email:
[email protected]
Ordercode: 43725 41
Helix S5000 Q4
Dimensions
Ordercode: 43725 42
©2018 Showtec
advertisement