Avantree TWS120 User Manual
Add to my manuals
8 Pages
Avantree TWS120 true wireless earbuds provide up to 36 hours of playtime with 8 hours in the earbuds and 3-3.5 charges in the charging case. Enjoy clear phone calls with enhanced noise isolation and a snug fit. Easily control music, volume, and calls with the touch-sensitive areas on the earbuds. The TWS120 can be used together or independently, allowing you to share music or take calls on one earbud while charging the other.
advertisement
User Manual
True Wireless Earbuds for
Clear Phone Calls
TWS120
Product Overview
Earbuds
L R
Charging case
Touch area
LED 1 LED 2
Included accessories
EarGels
L
Micro-USB Cable
M
S
How to wear
Select & replace eartips
To get the optimal experience, we recommend that you give each of the different sized eartips a try and find the pair that fits your ears the best. The medium-sized eartips are pre-mounted onto the earphones. Please ensure that the eartips are firmly attached.
Flip the eartips over and mount them onto the earphones. Then adjust the whole to aim at the microphone hole.
1
Microphone hole Overlapping microphone holes
Fitting adjustment
Insert the earphone into your ear and adjust to a position that you’re comfortable with. The better the fit, the better the noise isolation will be.
How to charge
With up to 8 hours of battery in the earphones, and 3-3.5 charges in the charging case, Avantree TWS120 offers up to 36 hours of playtime.
Charging the earphones
When you start hearing the “battery low” voice prompt, please charge the earphones by putting them back into the charging case. It takes about 1.5 hours to fully charge. The LED indicators on the earphones will illuminate RED while charging. Once the charging has completed, the LED indicators will turn WHITE for 10 seconds before automatically turning off.
battery low
Charging-Illuminate RED Fully charged-Illuminate White then go off
(Note: The earphones will automatically turn off about 10 minutes after the first low battery warning.)
2
Charging the case
Please charge the case if you see its left-side LED (LED 1) flashing RED . Charging the case will also charge the earphones if the earphones are inside the case.
Please use a DC 5V / 0.5-2A USB wall charger /car charger / computer USB port with the included Micro-USB cable to charge.
The left-side LED (LED 1) will illuminate RED while charging. When fully charged, the left-side LED (LED 1) will turn off and the right-side LED (LED 2) will illuminate GREEN .
DC 5V / 0.5-2A
OR
Basic operations
Function
Power On
Power Off
Pairing
Play / Pause
Volume Up
Volume Down
Previous Track
Next Track
Answer / End a Call
Operation
Open the case lid, LED light will illuminate WHITE for about 1s.
Put the earphones back into the charging case and close the case lid; they will power off and start charging. LED light will illuminate RED and then turn off.
Once powered on, the 2 earphones will connect with each other. The R earphone will enter pairing mode with its LED flashing WHITE and RED alternately.
Double tap the touch area on either earphone.
Slide up on the touch area on the L earphone.
Slide down on the touch area on the L earphone.
Slide up on the touch area on the R earphone.
Slide down on the touch area on the R earphone.
Double tap the touch area on either earphone.
LED Indications
For earphones
Connected with mobile device
Not connected with mobile device
LED on the R earphone double-flashes WHITE every 5s.
LED on the R earphone flashes WHITE once every 1s.
3
Earphones connected with each other LED on the L earphone double-flashes WHITE every 5s.
Earphones not connected with each other LED on the L earphone flashes WHITE once every 1s.
Battery low LEDs will flash RED 4 times every 2 mins.
Charging
Fully charged
LEDs stay SOLID RED .
RED LEDs turn to WHITE for about 10s then turn off.
For charging case
Battery low
Charging
Fully charged
Left-side LED (LED 1) flashes RED
Left-side LED (LED 1) stays SOLID RED
Right-side LED (LED 2) turns SOLID GREEN
How to pair
Connect to a Bluetooth device
1. Open the case to turn ON the earphones. Note: LED indicators on the earphones should already be flashing
WHITE .
2. Wait for LED on the R earphone to start flashing WHITE & RED alternately – Pairing Mode. (Fig 1-1)
3. Search & select Avantree TWS120 from the Bluetooth menu on your device, you will see Avantree TWS120 shown as “Connected”. (Fig 1-2)
4. The earphones will auto-reconnect to your device the next time you take them out of the case.
L
R
4:30
Settings Bluetooth
5G
Bluetooth
Now discoverable as “iPhone(2)”
MY DEVICES
Avantree HS134 Not Connected
OTHER DEVICES
Avantree TWS120
To pair an Apple Watch with your iPhone, go to the Watch app .
4:30
Settings Bluetooth
5G
Bluetooth
Now discoverable as “iPhone(2)”
MY DEVICES
Avantree TWS120
Avantree HS134
Connected
Not Connected
OTHER DEVICES
To pair an Apple Watch with your iPhone, go to the Watch app .
Fig 1-1 Fig 1-2
NOTE : to connect with ANOTHER device, please turn off Bluetooth on the previously connected device first.
Mono earphone use
Both R and L earphone can be used independently.
When you want to use the R earphone independently, please:
1. Open the case to turn on both earphones. (Fig 2-1)
2. Pick out the R earphone and close the case. Wait for auto-reconnection to your device. You will see Avantree
TWS120 shown as “Connected” and hear “Connected” from the R earphone. (Fig 2-2)
4
R
R
4G 4:30
Settings Bluetooth
Bluetooth
Now discoverable as “iPhone(2)”
MY DEVICES
Avantree TWS120
Avantree HS134
Connected
Not Connected
OTHER DEVICES
To pair an Apple Watch with your iPhone, go to the Watch app .
&
Connected
L
Fig 2-1 Fig 2-2
When you want to use the L earphone independently, please:
1. Open the case to turn on both earphones. (Fig 3-1)
2. Pick out the L earphone and close the case. Wait for LED on the L earphone to flash WHITE & RED alternately –
PAIRING MODE . (Fig 3-2)
3. Search & select Avantree TWS120S from the Bluetooth menu on your device. (Fig 3-3)
4:30
Settings Bluetooth
4G
L
R
L
Bluetooth
Now discoverable as “iPhone(2)”
MY DEVICES
Avantree TWS120S
Avantree HS134
Connected
Not Connected
OTHER DEVICES
To pair an Apple Watch with your iPhone, go to the app .
Watch
Fig 3-1 Fig 3-2 Fig 3-3
How to clear pairing history / reset
Reset the R earphone
1. Open the case to turn ON the earphones. Note: Earphone LED indicators should already be flashing WHITE. (Fig 4-1)
2. Wait for LED on the R earphone to flash WHITE & RED alternately – Pairing Mode. (Fig 4-2)
3. Long press the R earphone for about 10 seconds until LED lights on WHITE & RED simultaneously (looks like
PINK ) for about 5 seconds. (Fig 4-3)
R
Hold 10s
R
L
Fig 4-1 Fig 4-2 Fig 4-3
5
Reset the L earphone
1. Open the case and pick out the L earphone only. Then close the case. (Fig 5-1)
2. Wait for LED on the L earphone to flash WHITE & RED alternately – Pairing Mode. (Fig 5-2)
3. Long press the L earphone for about 10 seconds, until LED lights on WHITE & RED simultaneously (looks like
PINK ) for about 5 seconds. (Fig 5-3)
L
Hold 10s
R
L
Fig 5-1 Fig 5-2 Fig 5-3
Note: the steps above can only clear the pairing history between TWS120 / TWS120S with your Bluetooth device. If you experience one side sound, please visit here to connect the two earphones manually avantree.
com/tws120/video
Please forget / delete any TWS120 / TWS120S on the Bluetooth list of your device before you want to pair it again.
4:30
Settings Bluetooth
5G
Bluetooth
Now discoverable as “iPhone(2)”
MY DEVICES
Avantree TWS120
Avantree HS134
Connected
Not Connected
OTHER DEVICES
To pair an Apple Watch with your iPhone, go to the Watch app .
4:30
Bluetooth Avantree TWS120
Forget This Device
5G
Support
FAQ
View the FAQs on https://avantree.com/product-support/BTHS-TWS120-BLK .
6
How to take care of your TWS120
- Always store the earphones inside the charging case and make sure that they are safely protected.
- If you would like to clean your earphones, we recommend that you follow these instructions.
- The TWS120 is designed to function optimally between the temperatures of 0°C and 40°C (32-100°F.)
Although it can and will function beyond this temperature range, performance may be impaired.
- Avoid storing the earphones for extended periods of time without recharging them (max. three months.)
- The charging case is designed to charge using standard USB voltage (5v ± 0,25v). It is not recommended to charge this product using power supplies/sources with higher voltage.
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement